ARM: dts: sun7i: bananapi-m1-plus: Reindent whole file using tabs

The bananapi-m1-plus dts file was indented using 4 spaces, without
tabs. This does not match the code style.

Reindent the whole file before we do anything else.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
index 89e38e9..edfb5b3 100644 (file)
--- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
+++ b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
@@ -49,182 +49,182 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
-    model = "Banana Pi BPI-M1-Plus";
-    compatible = "sinovoip,bpi-m1-plus", "allwinner,sun7i-a20";
-
-    aliases {
-        serial0 = &uart0;
-    };
-
-    chosen {
-        stdout-path = "serial0:115200n8";
-    };
-
-    leds {
-        compatible = "gpio-leds";
-        pinctrl-names = "default";
-        pinctrl-0 = <&led_pins_bananapi>;
-
-        green {
-            label = "bananapi-m1-plus:green:usr";
-            gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
-        };
-
-        red {
-            label = "bananapi-m1-plus:red:usr";
-            gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
-            linux,default-trigger = "default-on";
-        };
-
-    };
-
-    mmc3_pwrseq: mmc3_pwrseq {
-        compatible = "mmc-pwrseq-simple";
-        pinctrl-names = "default";
-        pinctrl-0 = <&mmc3_pwrseq_pin_bananapim1plus>;
-        reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
-    };
-
-    reg_gmac_3v3: gmac-3v3 {
-        compatible = "regulator-fixed";
-        pinctrl-names = "default";
-        pinctrl-0 = <&gmac_power_pin_bananapi>;
-        regulator-name = "gmac-3v3";
-        regulator-min-microvolt = <3300000>;
-        regulator-max-microvolt = <3300000>;
-        startup-delay-us = <100000>;
-        enable-active-high;
-        gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
-    };
+       model = "Banana Pi BPI-M1-Plus";
+       compatible = "sinovoip,bpi-m1-plus", "allwinner,sun7i-a20";
+
+       aliases {
+               serial0 = &uart0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       leds {
+               compatible = "gpio-leds";
+               pinctrl-names = "default";
+               pinctrl-0 = <&led_pins_bananapi>;
+
+               green {
+                       label = "bananapi-m1-plus:green:usr";
+                       gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+               };
+
+               red {
+                       label = "bananapi-m1-plus:red:usr";
+                       gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "default-on";
+               };
+
+       };
+
+       mmc3_pwrseq: mmc3_pwrseq {
+               compatible = "mmc-pwrseq-simple";
+               pinctrl-names = "default";
+               pinctrl-0 = <&mmc3_pwrseq_pin_bananapim1plus>;
+               reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
+       };
+
+       reg_gmac_3v3: gmac-3v3 {
+               compatible = "regulator-fixed";
+               pinctrl-names = "default";
+               pinctrl-0 = <&gmac_power_pin_bananapi>;
+               regulator-name = "gmac-3v3";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               startup-delay-us = <100000>;
+               enable-active-high;
+               gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
+       };
 };
 
 &ahci {
-    status = "okay";
+       status = "okay";
 };
 
 &codec {
-    status = "okay";
+       status = "okay";
 };
 
 &ehci0 {
-    status = "okay";
+       status = "okay";
 };
 
 &ehci1 {
-    status = "okay";
+       status = "okay";
 };
 
 &gmac {
-    pinctrl-names = "default";
-    pinctrl-0 = <&gmac_pins_rgmii_a>;
-    phy = <&phy1>;
-    phy-mode = "rgmii";
-    phy-supply = <&reg_gmac_3v3>;
-    status = "okay";
-
-    phy1: ethernet-phy@1 {
-        reg = <1>;
-    };
+       pinctrl-names = "default";
+       pinctrl-0 = <&gmac_pins_rgmii_a>;
+       phy = <&phy1>;
+       phy-mode = "rgmii";
+       phy-supply = <&reg_gmac_3v3>;
+       status = "okay";
+
+       phy1: ethernet-phy@1 {
+               reg = <1>;
+       };
 };
 
 &i2c0 {
-    pinctrl-names = "default";
-    pinctrl-0 = <&i2c0_pins_a>;
-    status = "okay";
-
-    axp209: pmic@34 {
-        compatible = "x-powers,axp209";
-        reg = <0x34>;
-        interrupt-parent = <&nmi_intc>;
-        interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
-        interrupt-controller;
-        #interrupt-cells = <1>;
-    };
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c0_pins_a>;
+       status = "okay";
+
+       axp209: pmic@34 {
+               compatible = "x-powers,axp209";
+               reg = <0x34>;
+               interrupt-parent = <&nmi_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+               interrupt-controller;
+               #interrupt-cells = <1>;
+       };
 };
 
 &ir0 {
-    pinctrl-names = "default";
-    pinctrl-0 = <&ir0_rx_pins_a>;
-    status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&ir0_rx_pins_a>;
+       status = "okay";
 };
 
 &mmc0 {
-    pinctrl-names = "default";
-    pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
-    vmmc-supply = <&reg_vcc3v3>;
-    bus-width = <4>;
-    cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
-    cd-inverted;
-    status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
+       vmmc-supply = <&reg_vcc3v3>;
+       bus-width = <4>;
+       cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+       cd-inverted;
+       status = "okay";
 };
 
 &mmc3 {
-    #address-cells = <1>;
-    #size-cells = <0>;
-    pinctrl-names = "default";
-    pinctrl-0 = <&mmc3_pins_a>;
-    vmmc-supply = <&reg_vcc3v3>;
-    mmc-pwrseq = <&mmc3_pwrseq>;
-    bus-width = <4>;
-    non-removable;
-    enable-sdio-wakeup;
-    status = "okay";
-
-    brcmf: bcrmf@1 {
-        reg = <1>;
-        compatible = "brcm,bcm4329-fmac";
-        interrupt-parent = <&pio>;
-        interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
-        interrupt-names = "host-wake";
-    };
+       #address-cells = <1>;
+       #size-cells = <0>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc3_pins_a>;
+       vmmc-supply = <&reg_vcc3v3>;
+       mmc-pwrseq = <&mmc3_pwrseq>;
+       bus-width = <4>;
+       non-removable;
+       enable-sdio-wakeup;
+       status = "okay";
+
+       brcmf: bcrmf@1 {
+               reg = <1>;
+               compatible = "brcm,bcm4329-fmac";
+               interrupt-parent = <&pio>;
+               interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
+               interrupt-names = "host-wake";
+       };
 };
 
 &mmc3_pins_a {
-    /* AP6210 requires pull-up */
-    allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+       /* AP6210 requires pull-up */
+       allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 };
 
 &ohci0 {
-    status = "okay";
+       status = "okay";
 };
 
 &ohci1 {
-    status = "okay";
+       status = "okay";
 };
 
 &pio {
-    gmac_power_pin_bananapi: gmac_power_pin@0 {
-        allwinner,pins = "PH23";
-        allwinner,function = "gpio_out";
-        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-        allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-    };
-
-    led_pins_bananapi: led_pins@0 {
-        allwinner,pins = "PH24", "PG2";
-        allwinner,function = "gpio_out";
-        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-        allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-    };
-
-    mmc0_cd_pin_bananapi: mmc0_cd_pin@0 {
-        allwinner,pins = "PH10";
-        allwinner,function = "gpio_in";
-        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-        allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-    };
-
-    mmc3_pwrseq_pin_bananapim1plus: mmc3_pwrseq_pin@0 {
-        allwinner,pins = "PH22";
-        allwinner,function = "gpio_out";
-        allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-        allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-    };
+       gmac_power_pin_bananapi: gmac_power_pin@0 {
+               allwinner,pins = "PH23";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       led_pins_bananapi: led_pins@0 {
+               allwinner,pins = "PH24", "PG2";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       mmc0_cd_pin_bananapi: mmc0_cd_pin@0 {
+               allwinner,pins = "PH10";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+       };
+
+       mmc3_pwrseq_pin_bananapim1plus: mmc3_pwrseq_pin@0 {
+               allwinner,pins = "PH22";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
 };
 
 &uart0 {
-    pinctrl-names = "default";
-    pinctrl-0 = <&uart0_pins_a>;
-    status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pins_a>;
+       status = "okay";
 };