dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
status = "okay";
};
+&pcie {
+ status = "okay";
+};
+
&sai2 {
status = "okay";
};
interrupts = <0 126 IRQ_TYPE_LEVEL_HIGH>;
};
- pcie@3400000 {
+ pcie: pcie@3400000 {
compatible = "fsl,ls1012a-pcie";
reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
0x40 0x00000000 0x0 0x00002000>; /* configuration space */
device_type = "memory";
reg = <0x0 0x80000000 0x1 0x00000000>;
};
+
+ sys_mclk: clock-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "Speaker Ext",
+ "Line", "Line In Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "Microphone Jack", "Mic Bias",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "Speaker Ext", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai1>;
+ frame-master;
+ bitclock-master;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ frame-master;
+ bitclock-master;
+ system-clock-frequency = <25000000>;
+ };
+ };
};
&duart0 {
reg = <0x57>;
};
};
+
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x5>;
+
+ sgtl5000: audio-codec@a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ VDDA-supply = <®_1p8v>;
+ VDDIO-supply = <®_1p8v>;
+ clocks = <&sys_mclk>;
+ };
+ };
};
};
+
+&sai1 {
+ status = "okay";
+};
device_type = "memory";
reg = <0x0 0x80000000 0x1 0x0000000>;
};
+
+ sys_mclk: clock-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "Speaker Ext",
+ "Line", "Line In Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "Microphone Jack", "Mic Bias",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "Speaker Ext", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai4>;
+ frame-master;
+ bitclock-master;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ frame-master;
+ bitclock-master;
+ system-clock-frequency = <25000000>;
+ };
+ };
};
&i2c0 {
#address-cells = <1>;
#size-cells = <0>;
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+
+ sgtl5000: audio-codec@a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ VDDA-supply = <®_1p8v>;
+ VDDIO-supply = <®_1p8v>;
+ clocks = <&sys_mclk>;
+ sclk-strength = <3>;
+ };
+ };
+
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
&enetc_port1 {
status = "disabled";
};
+
+&sai4 {
+ status = "okay";
+};
IRQ_TYPE_LEVEL_LOW)>;
};
+ pmu {
+ compatible = "arm,cortex-a72-pmu";
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
gic: interrupt-controller@6000000 {
compatible= "arm,gic-v3";
#address-cells = <2>;
status = "disabled";
};
+ edma0: dma-controller@22c0000 {
+ #dma-cells = <2>;
+ compatible = "fsl,vf610-edma";
+ reg = <0x0 0x22c0000 0x0 0x10000>,
+ <0x0 0x22d0000 0x0 0x10000>,
+ <0x0 0x22e0000 0x0 0x10000>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "edma-tx", "edma-err";
+ dma-channels = <32>;
+ clock-names = "dmamux0", "dmamux1";
+ clocks = <&clockgen 4 1>,
+ <&clockgen 4 1>;
+ };
+
gpio1: gpio@2300000 {
compatible = "fsl,qoriq-gpio";
reg = <0x0 0x2300000 0x0 0x10000>;
sata: sata@3200000 {
compatible = "fsl,ls1028a-ahci";
reg = <0x0 0x3200000 0x0 0x10000>,
- <0x0 0x20140520 0x0 0x4>;
+ <0x7 0x100520 0x0 0x4>;
reg-names = "ahci", "sata-ecc";
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clockgen 4 1>;
<GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
};
+ sai1: audio-controller@f100000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,vf610-sai";
+ reg = <0x0 0xf100000 0x0 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+ <&clockgen 4 1>, <&clockgen 4 1>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx", "rx";
+ dmas = <&edma0 1 4>,
+ <&edma0 1 3>;
+ status = "disabled";
+ };
+
+ sai2: audio-controller@f110000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,vf610-sai";
+ reg = <0x0 0xf110000 0x0 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+ <&clockgen 4 1>, <&clockgen 4 1>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx", "rx";
+ dmas = <&edma0 1 6>,
+ <&edma0 1 5>;
+ status = "disabled";
+ };
+
+ sai4: audio-controller@f130000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,vf610-sai";
+ reg = <0x0 0xf130000 0x0 0x10000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+ <&clockgen 4 1>, <&clockgen 4 1>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx", "rx";
+ dmas = <&edma0 1 10>,
+ <&edma0 1 9>;
+ status = "disabled";
+ };
+
pcie@1f0000000 { /* Integrated Endpoint Root Complex */
compatible = "pci-host-ecam-generic";
reg = <0x01 0xf0000000 0x0 0x100000>;
model = "LS1043A RDB Board";
aliases {
- crypto = &crypto;
serial0 = &duart0;
serial1 = &duart1;
serial2 = &duart2;
#size-cells = <2>;
aliases {
+ crypto = &crypto;
fman0 = &fman0;
ethernet0 = &enet0;
ethernet1 = &enet1;
interrupts = <0 99 0x4>;
clock-names = "qspi_en", "qspi";
clocks = <&clockgen 4 0>, <&clockgen 4 0>;
- big-endian;
status = "disabled";
};
interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "qspi_en", "qspi";
clocks = <&clockgen 4 1>, <&clockgen 4 1>;
- big-endian;
- fsl,qspi-has-second-chip;
status = "disabled";
};
};
};
+&sata0 {
+ status = "okay";
+};
+
+&sata1 {
+ status = "okay";
+};
+
+&sata2 {
+ status = "okay";
+};
+
+&sata3 {
+ status = "okay";
+};
+
&uart0 {
status = "okay";
};
};
};
+&sata0 {
+ status = "okay";
+};
+
+&sata1 {
+ status = "okay";
+};
+
+&sata2 {
+ status = "okay";
+};
+
+&sata3 {
+ status = "okay";
+};
+
&uart0 {
status = "okay";
};
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster0_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@1 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster0_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@100 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster1_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@101 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster1_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@200 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster2_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@201 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster2_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@300 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster3_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@301 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster3_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@400 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster4_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@401 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster4_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@500 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster5_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@501 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster5_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@600 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster6_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@601 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster6_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@700 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster7_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cpu@701 {
i-cache-line-size = <64>;
i-cache-sets = <192>;
next-level-cache = <&cluster7_l2>;
+ cpu-idle-states = <&cpu_pw20>;
};
cluster0_l2: l2-cache0 {
cache-sets = <1024>;
cache-level = <2>;
};
+
+ cpu_pw20: cpu-pw20 {
+ compatible = "arm,idle-state";
+ idle-state-name = "PW20";
+ arm,psci-suspend-param = <0x0>;
+ entry-latency-us = <2000>;
+ exit-latency-us = <2000>;
+ min-residency-us = <6000>;
+ };
};
gic: interrupt-controller@6000000 {
status = "disabled";
};
+ sata0: sata@3200000 {
+ compatible = "fsl,lx2160a-ahci";
+ reg = <0x0 0x3200000 0x0 0x10000>,
+ <0x7 0x100520 0x0 0x4>;
+ reg-names = "ahci", "sata-ecc";
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 3>;
+ dma-coherent;
+ status = "disabled";
+ };
+
+ sata1: sata@3210000 {
+ compatible = "fsl,lx2160a-ahci";
+ reg = <0x0 0x3210000 0x0 0x10000>,
+ <0x7 0x100520 0x0 0x4>;
+ reg-names = "ahci", "sata-ecc";
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 3>;
+ dma-coherent;
+ status = "disabled";
+ };
+
+ sata2: sata@3220000 {
+ compatible = "fsl,lx2160a-ahci";
+ reg = <0x0 0x3220000 0x0 0x10000>,
+ <0x7 0x100520 0x0 0x4>;
+ reg-names = "ahci", "sata-ecc";
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 3>;
+ dma-coherent;
+ status = "disabled";
+ };
+
+ sata3: sata@3230000 {
+ compatible = "fsl,lx2160a-ahci";
+ reg = <0x0 0x3230000 0x0 0x10000>,
+ <0x7 0x100520 0x0 0x4>;
+ reg-names = "ahci", "sata-ecc";
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 3>;
+ dma-coherent;
+ status = "disabled";
+ };
+
smmu: iommu@5000000 {
compatible = "arm,mmu-500";
reg = <0 0x5000000 0 0x800000>;
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ */
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+
+/ {
+ model = "FSL i.MX8MM EVK board";
+ compatible = "fsl,imx8mm-evk", "fsl,imx8mm";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_led>;
+
+ status {
+ label = "status";
+ gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ reg_usdhc2_vmmc: regulator-usdhc2 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ at803x,led-act-blind-workaround;
+ at803x,eee-okay;
+ at803x,vddio-1p8v;
+ };
+ };
+};
+
+&uart2 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
+ >;
+ };
+
+ pinctrl_gpio_led: gpioledgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
+ MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <dt-bindings/clock/imx8mm-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "imx8mm-pinfunc.h"
+
+/ {
+ compatible = "fsl,imx8mm";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ ethernet0 = &fec1;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ spi0 = &ecspi1;
+ spi1 = &ecspi2;
+ spi2 = &ecspi3;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ A53_0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clk IMX8MM_CLK_ARM>;
+ enable-method = "psci";
+ next-level-cache = <&A53_L2>;
+ operating-points-v2 = <&a53_opp_table>;
+ };
+
+ A53_1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x1>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clk IMX8MM_CLK_ARM>;
+ enable-method = "psci";
+ next-level-cache = <&A53_L2>;
+ operating-points-v2 = <&a53_opp_table>;
+ };
+
+ A53_2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x2>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clk IMX8MM_CLK_ARM>;
+ enable-method = "psci";
+ next-level-cache = <&A53_L2>;
+ operating-points-v2 = <&a53_opp_table>;
+ };
+
+ A53_3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clk IMX8MM_CLK_ARM>;
+ enable-method = "psci";
+ next-level-cache = <&A53_L2>;
+ operating-points-v2 = <&a53_opp_table>;
+ };
+
+ A53_L2: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+
+ a53_opp_table: opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <850000>;
+ clock-latency-ns = <150000>;
+ };
+
+ opp-1600000000 {
+ opp-hz = /bits/ 64 <1600000000>;
+ opp-microvolt = <900000>;
+ clock-latency-ns = <150000>;
+ opp-suspend;
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x0 0x40000000 0 0x80000000>;
+ };
+
+ osc_32k: clock-osc-32k {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "osc_32k";
+ };
+
+ osc_24m: clock-osc-24m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc_24m";
+ };
+
+ clk_ext1: clock-ext1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133000000>;
+ clock-output-names = "clk_ext1";
+ };
+
+ clk_ext2: clock-ext2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133000000>;
+ clock-output-names = "clk_ext2";
+ };
+
+ clk_ext3: clock-ext3 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133000000>;
+ clock-output-names = "clk_ext3";
+ };
+
+ clk_ext4: clock-ext4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <133000000>;
+ clock-output-names = "clk_ext4";
+ };
+
+ gic: interrupt-controller@38800000 {
+ compatible = "arm,gic-v3";
+ reg = <0x0 0x38800000 0 0x10000>, /* GIC Dist */
+ <0x0 0x38880000 0 0xC0000>; /* GICR (RD_base + SGI_base) */
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 7
+ (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-affinity = <&A53_0>, <&A53_1>, <&A53_2>, <&A53_3>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Secure */
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Non-Secure */
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Virtual */
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; /* Hypervisor */
+ clock-frequency = <8000000>;
+ arm,no-tick-in-suspend;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x0 0x3e000000>;
+
+ aips1: bus@30000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio1: gpio@30200000 {
+ compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
+ reg = <0x30200000 0x10000>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@30210000 {
+ compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
+ reg = <0x30210000 0x10000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@30220000 {
+ compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
+ reg = <0x30220000 0x10000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio@30230000 {
+ compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
+ reg = <0x30230000 0x10000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio5: gpio@30240000 {
+ compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
+ reg = <0x30240000 0x10000>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wdog1: watchdog@30280000 {
+ compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
+ reg = <0x30280000 0x10000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_WDOG1_ROOT>;
+ status = "disabled";
+ };
+
+ wdog2: watchdog@30290000 {
+ compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
+ reg = <0x30290000 0x10000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_WDOG2_ROOT>;
+ status = "disabled";
+ };
+
+ wdog3: watchdog@302a0000 {
+ compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
+ reg = <0x302a0000 0x10000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_WDOG3_ROOT>;
+ status = "disabled";
+ };
+
+ sdma2: dma-controller@302c0000 {
+ compatible = "fsl,imx8mm-sdma", "fsl,imx7d-sdma";
+ reg = <0x302c0000 0x10000>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SDMA2_ROOT>,
+ <&clk IMX8MM_CLK_SDMA2_ROOT>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
+ };
+
+ sdma3: dma-controller@302b0000 {
+ compatible = "fsl,imx8mm-sdma", "fsl,imx7d-sdma";
+ reg = <0x302b0000 0x10000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SDMA3_ROOT>,
+ <&clk IMX8MM_CLK_SDMA3_ROOT>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
+ };
+
+ iomuxc: pinctrl@30330000 {
+ compatible = "fsl,imx8mm-iomuxc";
+ reg = <0x30330000 0x10000>;
+ };
+
+ gpr: iomuxc-gpr@30340000 {
+ compatible = "fsl,imx8mm-iomuxc-gpr", "syscon";
+ reg = <0x30340000 0x10000>;
+ };
+
+ ocotp: ocotp-ctrl@30350000 {
+ compatible = "fsl,imx8mm-ocotp", "fsl,imx7d-ocotp", "syscon";
+ reg = <0x30350000 0x10000>;
+ clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>;
+ /* For nvmem subnodes */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ anatop: anatop@30360000 {
+ compatible = "fsl,imx8mm-anatop", "syscon", "simple-bus";
+ reg = <0x30360000 0x10000>;
+ };
+
+ snvs: snvs@30370000 {
+ compatible = "fsl,sec-v4.0-mon","syscon", "simple-mfd";
+ reg = <0x30370000 0x10000>;
+
+ snvs_rtc: snvs-rtc-lp {
+ compatible = "fsl,sec-v4.0-mon-rtc-lp";
+ regmap = <&snvs>;
+ offset = <0x34>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ snvs_pwrkey: snvs-powerkey {
+ compatible = "fsl,sec-v4.0-pwrkey";
+ regmap = <&snvs>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ linux,keycode = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ clk: clock-controller@30380000 {
+ compatible = "fsl,imx8mm-ccm";
+ reg = <0x30380000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, <&clk_ext2>,
+ <&clk_ext3>, <&clk_ext4>;
+ clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2",
+ "clk_ext3", "clk_ext4";
+ };
+
+ src: reset-controller@30390000 {
+ compatible = "fsl,imx8mm-src", "syscon";
+ reg = <0x30390000 0x10000>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ };
+ };
+
+ aips2: bus@30400000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pwm1: pwm@30660000 {
+ compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
+ reg = <0x30660000 0x10000>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_PWM1_ROOT>,
+ <&clk IMX8MM_CLK_PWM1_ROOT>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@30670000 {
+ compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
+ reg = <0x30670000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_PWM2_ROOT>,
+ <&clk IMX8MM_CLK_PWM2_ROOT>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@30680000 {
+ compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
+ reg = <0x30680000 0x10000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_PWM3_ROOT>,
+ <&clk IMX8MM_CLK_PWM3_ROOT>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm4: pwm@30690000 {
+ compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
+ reg = <0x30690000 0x10000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_PWM4_ROOT>,
+ <&clk IMX8MM_CLK_PWM4_ROOT>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+ };
+
+ aips3: bus@30800000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ ecspi1: spi@30820000 {
+ compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30820000 0x10000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_ECSPI1_ROOT>,
+ <&clk IMX8MM_CLK_ECSPI1_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ecspi2: spi@30830000 {
+ compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30830000 0x10000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_ECSPI2_ROOT>,
+ <&clk IMX8MM_CLK_ECSPI2_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ecspi3: spi@30840000 {
+ compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30840000 0x10000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_ECSPI3_ROOT>,
+ <&clk IMX8MM_CLK_ECSPI3_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@30860000 {
+ compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart";
+ reg = <0x30860000 0x10000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_UART1_ROOT>,
+ <&clk IMX8MM_CLK_UART1_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@30880000 {
+ compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart";
+ reg = <0x30880000 0x10000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_UART3_ROOT>,
+ <&clk IMX8MM_CLK_UART3_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@30890000 {
+ compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart";
+ reg = <0x30890000 0x10000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_UART2_ROOT>,
+ <&clk IMX8MM_CLK_UART2_ROOT>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ i2c1: i2c@30a20000 {
+ compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30a20000 0x10000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_I2C1_ROOT>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@30a30000 {
+ compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30a30000 0x10000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_I2C2_ROOT>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@30a40000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c";
+ reg = <0x30a40000 0x10000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_I2C3_ROOT>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@30a50000 {
+ compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30a50000 0x10000>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_I2C4_ROOT>;
+ status = "disabled";
+ };
+
+ uart4: serial@30a60000 {
+ compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart";
+ reg = <0x30a60000 0x10000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_UART4_ROOT>,
+ <&clk IMX8MM_CLK_UART4_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 28 4 0>, <&sdma1 29 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ usdhc1: mmc@30b40000 {
+ compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
+ reg = <0x30b40000 0x10000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
+ <&clk IMX8MM_CLK_USDHC1_ROOT>;
+ clock-names = "ipg", "ahb", "per";
+ assigned-clocks = <&clk IMX8MM_CLK_USDHC1>;
+ assigned-clock-rates = <400000000>;
+ fsl,tuning-start-tap = <20>;
+ fsl,tuning-step= <2>;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc2: mmc@30b50000 {
+ compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
+ reg = <0x30b50000 0x10000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
+ <&clk IMX8MM_CLK_USDHC2_ROOT>;
+ clock-names = "ipg", "ahb", "per";
+ fsl,tuning-start-tap = <20>;
+ fsl,tuning-step= <2>;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc3: mmc@30b60000 {
+ compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
+ reg = <0x30b60000 0x10000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
+ <&clk IMX8MM_CLK_USDHC3_ROOT>;
+ clock-names = "ipg", "ahb", "per";
+ assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+ assigned-clock-rates = <400000000>;
+ fsl,tuning-start-tap = <20>;
+ fsl,tuning-step= <2>;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ sdma1: dma-controller@30bd0000 {
+ compatible = "fsl,imx8mm-sdma", "fsl,imx7d-sdma";
+ reg = <0x30bd0000 0x10000>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_SDMA1_ROOT>,
+ <&clk IMX8MM_CLK_SDMA1_ROOT>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
+ };
+
+ fec1: ethernet@30be0000 {
+ compatible = "fsl,imx8mm-fec", "fsl,imx6sx-fec";
+ reg = <0x30be0000 0x10000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_ENET1_ROOT>,
+ <&clk IMX8MM_CLK_ENET1_ROOT>,
+ <&clk IMX8MM_CLK_ENET_TIMER>,
+ <&clk IMX8MM_CLK_ENET_REF>,
+ <&clk IMX8MM_CLK_ENET_PHY_REF>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ assigned-clocks = <&clk IMX8MM_CLK_ENET_AXI>,
+ <&clk IMX8MM_CLK_ENET_TIMER>,
+ <&clk IMX8MM_CLK_ENET_REF>,
+ <&clk IMX8MM_CLK_ENET_TIMER>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_266M>,
+ <&clk IMX8MM_SYS_PLL2_100M>,
+ <&clk IMX8MM_SYS_PLL2_125M>;
+ assigned-clock-rates = <0>, <0>, <125000000>, <100000000>;
+ fsl,num-tx-queues = <3>;
+ fsl,num-rx-queues = <3>;
+ status = "disabled";
+ };
+
+ };
+
+ aips4: bus@32c00000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usbotg1: usb@32e40000 {
+ compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
+ reg = <0x32e40000 0x200>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>;
+ clock-names = "usb1_ctrl_root_clk";
+ assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>,
+ <&clk IMX8MM_CLK_USB_CORE_REF>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>,
+ <&clk IMX8MM_SYS_PLL1_100M>;
+ fsl,usbphy = <&usbphynop1>;
+ fsl,usbmisc = <&usbmisc1 0>;
+ status = "disabled";
+ };
+
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+ assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
+ clock-names = "main_clk";
+ };
+
+ usbmisc1: usbmisc@32e40200 {
+ compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc";
+ #index-cells = <1>;
+ reg = <0x32e40200 0x200>;
+ };
+
+ usbotg2: usb@32e50000 {
+ compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
+ reg = <0x32e50000 0x200>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>;
+ clock-names = "usb1_ctrl_root_clk";
+ assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>,
+ <&clk IMX8MM_CLK_USB_CORE_REF>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>,
+ <&clk IMX8MM_SYS_PLL1_100M>;
+ fsl,usbphy = <&usbphynop2>;
+ fsl,usbmisc = <&usbmisc2 0>;
+ status = "disabled";
+ };
+
+ usbphynop2: usbphynop2 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+ assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
+ clock-names = "main_clk";
+ };
+
+ usbmisc2: usbmisc@32e50200 {
+ compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc";
+ #index-cells = <1>;
+ reg = <0x32e50200 0x200>;
+ };
+
+ };
+
+ dma_apbh: dma-controller@33000000 {
+ compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
+ reg = <0x33000000 0x2000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+ #dma-cells = <1>;
+ dma-channels = <4>;
+ clocks = <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
+ };
+
+ gpmi: nand-controller@33002000{
+ compatible = "fsl,imx8mm-gpmi-nand", "fsl,imx7d-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "bch";
+ clocks = <&clk IMX8MM_CLK_NAND_ROOT>,
+ <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
+ clock-names = "gpmi_io", "gpmi_bch_apb";
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
+ status = "disabled";
+ };
+ };
+};
reg = <0x00000000 0x40000000 0 0xc0000000>;
};
+ pcie0_refclk: pcie0-refclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
reg_usdhc2_vmmc: regulator-vsd-3v3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_usdhc2>;
gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ buck2_reg: regulator-buck2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_buck2>;
+ compatible = "regulator-gpio";
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1000000>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+ states = <1000000 0x0
+ 900000 0x1>;
+ };
+
+ wm8524: audio-codec {
+ #sound-dai-cells = <0>;
+ compatible = "wlf,wm8524";
+ wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ };
+
+ sound-wm8524 {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "wm8524-audio";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&cpudai>;
+ simple-audio-card,bitclock-master = <&cpudai>;
+ simple-audio-card,widgets =
+ "Line", "Left Line Out Jack",
+ "Line", "Right Line Out Jack";
+ simple-audio-card,routing =
+ "Left Line Out Jack", "LINEVOUTL",
+ "Right Line Out Jack", "LINEVOUTR";
+
+ cpudai: simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ };
+
+ link_codec: simple-audio-card,codec {
+ sound-dai = <&wm8524>;
+ clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2_reg>;
};
&fec1 {
};
};
+&sai2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2>;
+ assigned-clocks = <&clk IMX8MQ_CLK_SAI2>;
+ assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ status = "okay";
+};
+
+&gpio5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_reset>;
+
+ wl-reg-on {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+};
+
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
};
};
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie0>;
+ reset-gpio = <&gpio5 28 GPIO_ACTIVE_LOW>;
+ clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE1_AUX>,
+ <&clk IMX8MQ_CLK_PCIE1_PHY>,
+ <&pcie0_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ status = "okay";
+};
+
+&pgc_gpu {
+ power-supply = <&sw1a_reg>;
+};
+
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
};
&iomuxc {
+ pinctrl_buck2: vddarmgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x19
+ >;
+
+ };
+
pinctrl_fec1: fec1grp {
fsl,pins = <
MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
>;
};
+ pinctrl_pcie0: pcie0grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x76
+ MX8MQ_IOMUXC_UART4_RXD_GPIO5_IO28 0x16
+ >;
+ };
+
pinctrl_qspi: qspigrp {
fsl,pins = <
MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
>;
};
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6
+ MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6
+ MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6
+ MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0xd6
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
>;
};
+
+ pinctrl_wifi_reset: wifiresetgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART4_TXD_GPIO5_IO29 0x16
+ >;
+ };
};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2019 Zodiac Inflight Innovations
+ */
+
+/dts-v1/;
+
+#include "imx8mq-zii-ultra.dtsi"
+
+/ {
+ model = "ZII i.MX8MQ Ultra RMB3 Board";
+ compatible = "zii,imx8mq-ultra-rmb3", "zii,imx8mq-ultra", "fsl,imx8mq";
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ nor_flash: flash@0 {
+ compatible = "st,n25q128a13", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
+
+&i2c2 {
+ temp-sense@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+};
+
+&i2c4 {
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ts>;
+ reg = <0x20>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <2>;
+ };
+
+ rmi4-f11@11 {
+ reg = <0x11>;
+ touchscreen-inverted-x;
+ touchscreen-swapped-x-y;
+ syna,sensor-type = <1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ touchscreen-inverted-x;
+ touchscreen-swapped-x-y;
+ syna,sensor-type = <1>;
+ };
+ };
+
+ touchscreen@2a {
+ compatible = "eeti,exc3000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ts>;
+ reg = <0x2a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+ touchscreen-inverted-x;
+ touchscreen-swapped-x-y;
+ status = "disabled";
+ };
+};
+
+&usbhub {
+ swap-dx-lanes = <0>;
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19
+ MX8MQ_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82
+ MX8MQ_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
+ MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2019 Zodiac Inflight Innovations
+ */
+
+/dts-v1/;
+
+#include "imx8mq-zii-ultra.dtsi"
+
+/ {
+ model = "ZII i.MX8MQ Ultra Zest Board";
+ compatible = "zii,imx8mq-ultra-zest", "zii,imx8mq-ultra", "fsl,imx8mq";
+};
+
+&i2c4 {
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ts>;
+ reg = <0x4a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2019 Zodiac Inflight Innovations
+ */
+
+#include "imx8mq.dtsi"
+
+/ {
+ aliases {
+ mdio-gpio0 = &mdio0;
+ rtc0 = &ds1341;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ mdio0: bitbang-mdio {
+ compatible = "virtual,mdio-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mdio_bitbang>, <&pinctrl_fec1_phy_reset>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio1 14 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ pcie0_refclk: clock-pcie0-refclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ pcie1_refclk: clock-pcie1-refclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ reg_12p0_main: regulator-12p0-main {
+ compatible = "regulator-fixed";
+ regulator-name = "12V_MAIN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_5p0_main: regulator-5p0-main {
+ compatible = "regulator-fixed";
+ vin-supply = <®_12p0_main>;
+ regulator-name = "5V_MAIN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_3p3_main: regulator-3p3-main {
+ compatible = "regulator-fixed";
+ vin-supply = <®_12p0_main>;
+ regulator-name = "3V3V_MAIN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_5p0_user_usb: regulator-5p0-user-usb {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_user_usb>;
+ vin-supply = <®_5p0_main>;
+ regulator-name = "5V_USER_USB";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ startup-delay-us = <1000>;
+ };
+
+ reg_usdhc2_vmmc: regulator-vsd-3v3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2>;
+ compatible = "regulator-fixed";
+ vin-supply = <®_3p3_main>;
+ regulator-name = "3V3_SD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_arm: regulator-arm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_arm>;
+ compatible = "regulator-gpio";
+ vin-supply = <®_12p0_main>;
+ regulator-name = "0V9_ARM";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1000000>;
+ gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ states = <1000000 0x0
+ 900000 0x1>;
+ regulator-always-on;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <®_arm>;
+};
+
+&A53_1 {
+ cpu-supply = <®_arm>;
+};
+
+&A53_2 {
+ cpu-supply = <®_arm>;
+};
+
+&A53_3 {
+ cpu-supply = <®_arm>;
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+
+ phy-handle = <&phy0>;
+ phy-mode = "rmii";
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ switch: switch@0 {
+ compatible = "marvell,mv88e6085";
+ pinctrl-0 = <&pinctrl_switch_irq>;
+ pinctrl-names = "default";
+ reg = <0>;
+ dsa,member = <0 0>;
+ eeprom-length = <512>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "gigabit_proc";
+ phy-handle = <&switchphy0>;
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "netaux";
+ phy-handle = <&switchphy1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "cpu";
+ ethernet = <&fec1>;
+
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "netright";
+ phy-handle = <&switchphy3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "netleft";
+ phy-handle = <&switchphy4>;
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switchphy0: switchphy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ switchphy1: switchphy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ switchphy2: switchphy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ switchphy3: switchphy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ switchphy4: switchphy@4 {
+ reg = <4>;
+ interrupt-parent = <&switch>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+ };
+ };
+};
+
+&gpio3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio3_hog>;
+
+ usb-emulation {
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "usb-emulation";
+ };
+
+ usb-mode1 {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-mode1";
+ };
+
+ usb-mode2 {
+ gpio-hog;
+ gpios = <13 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-mode2";
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pmic@8 {
+ compatible = "fsl,pfuze100";
+ reg = <0x8>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3ab {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <975000>;
+ regulator-always-on;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1675000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1625000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3625000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+
+ ds1341: rtc@68 {
+ compatible = "dallas,ds1341";
+ reg = <0x68>;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ usbhub: usbhub@2c {
+ compatible ="microchip,usb2513b";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbhub>;
+ reg = <0x2c>;
+ reset-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+
+ rave-sp {
+ compatible = "zii,rave-sp-rdu2";
+ current-speed = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ watchdog {
+ compatible = "zii,rave-sp-watchdog";
+ };
+
+ backlight {
+ compatible = "zii,rave-sp-backlight";
+ };
+
+ pwrbutton {
+ compatible = "zii,rave-sp-pwrbutton";
+ };
+
+ eeprom@a3 {
+ compatible = "zii,rave-sp-eeprom";
+ reg = <0xa3 0x4000>;
+ zii,eeprom-name = "dds-eeprom";
+ };
+
+ eeprom@a4 {
+ compatible = "zii,rave-sp-eeprom";
+ reg = <0xa4 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ zii,eeprom-name = "main-eeprom";
+ };
+ };
+};
+
+&usb3_phy0 {
+ vbus-supply = <®_5p0_user_usb>;
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb3_phy1 {
+ vbus-supply = <®_5p0_main>;
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie0>;
+ reset-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE1_AUX>,
+ <&clk IMX8MQ_CLK_PCIE1_PHY>,
+ <&pcie0_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ status = "okay";
+};
+
+&pcie1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie1>;
+ reset-gpio = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE2_AUX>,
+ <&clk IMX8MQ_CLK_PCIE2_PHY>,
+ <&pcie1_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ status = "okay";
+};
+
+&pgc_gpu {
+ power-supply = <&sw1a_reg>;
+};
+
+&pgc_vpu {
+ power-supply = <&sw1c_reg>;
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ vqmmc-supply = <&sw4_reg>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&snvs_rtc {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_TX_CLK 0x1f
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RX_ER 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ >;
+ };
+
+ pinctrl_fec1_phy_reset: fec1phyresetgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_RD3_GPIO1_IO29 0x11
+ >;
+ };
+
+ pinctrl_gpio3_hog: gpio3hoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10 0x6
+ MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x6
+ MX8MQ_IOMUXC_NAND_DATA07_GPIO3_IO13 0x6
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_mdio_bitbang: bitbangmdiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x44
+ MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x64
+ >;
+ };
+
+ pinctrl_pcie0: pcie0grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART4_RXD_PCIE1_CLKREQ_B 0x66
+ MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x6
+ >;
+ };
+
+ pinctrl_pcie1: pcie1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART4_TXD_PCIE2_CLKREQ_B 0x66
+ MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x6
+ >;
+ };
+
+ pinctrl_reg_arm: regarmgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19
+ >;
+ };
+
+ pinctrl_reg_usdhc2: regusdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_reg_user_usb: reguserusbgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x6
+ >;
+ };
+
+ pinctrl_switch_irq: switchgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41
+ >;
+ };
+
+ pinctrl_ts: tsgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x96
+ MX8MQ_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x96
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_usbhub: usbhubgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x41
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x85
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc5
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc5
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc5
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc5
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc5
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x87
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc7
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc7
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc7
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc7
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc7
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+};
#include <dt-bindings/clock/imx8mq-clock.h>
#include <dt-bindings/power/imx8mq-power.h>
+#include <dt-bindings/reset/imx8mq-reset.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
#include "imx8mq-pinfunc.h"
/ {
device_type = "cpu";
compatible = "arm,cortex-a53";
reg = <0x0>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clk IMX8MQ_CLK_ARM>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ operating-points-v2 = <&a53_opp_table>;
+ #cooling-cells = <2>;
};
A53_1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a53";
reg = <0x1>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clk IMX8MQ_CLK_ARM>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ operating-points-v2 = <&a53_opp_table>;
+ #cooling-cells = <2>;
};
A53_2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a53";
reg = <0x2>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clk IMX8MQ_CLK_ARM>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ operating-points-v2 = <&a53_opp_table>;
+ #cooling-cells = <2>;
};
A53_3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a53";
reg = <0x3>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clk IMX8MQ_CLK_ARM>;
enable-method = "psci";
next-level-cache = <&A53_L2>;
+ operating-points-v2 = <&a53_opp_table>;
+ #cooling-cells = <2>;
};
A53_L2: l2-cache0 {
};
};
+ a53_opp_table: opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt = <900000>;
+ clock-latency-ns = <150000>;
+ };
+
+ opp-1300000000 {
+ opp-hz = /bits/ 64 <1300000000>;
+ opp-microvolt = <1000000>;
+ clock-latency-ns = <150000>;
+ opp-suspend;
+ };
+ };
+
pmu {
compatible = "arm,cortex-a53-pmu";
interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
method = "smc";
};
+ thermal-zones {
+ cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu 0>;
+
+ trips {
+ cpu_alert: cpu-alert {
+ temperature = <80000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu-crit {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert>;
+ cooling-device =
+ <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ gpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu 1>;
+
+ trips {
+ gpu-crit {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ vpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu 2>;
+
+ trips {
+ vpu-crit {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */
reg = <0x30200000 0x10000>;
interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_GPIO1_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
reg = <0x30210000 0x10000>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_GPIO2_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
reg = <0x30220000 0x10000>;
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_GPIO3_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
reg = <0x30230000 0x10000>;
interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_GPIO4_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
reg = <0x30240000 0x10000>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_GPIO5_ROOT>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
+ tmu: tmu@30260000 {
+ compatible = "fsl,imx8mq-tmu";
+ reg = <0x30260000 0x10000>;
+ interrupt = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ little-endian;
+ fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>;
+ fsl,tmu-calibration = <0x00000000 0x00000023
+ 0x00000001 0x00000029
+ 0x00000002 0x0000002f
+ 0x00000003 0x00000035
+ 0x00000004 0x0000003d
+ 0x00000005 0x00000043
+ 0x00000006 0x0000004b
+ 0x00000007 0x00000051
+ 0x00000008 0x00000057
+ 0x00000009 0x0000005f
+ 0x0000000a 0x00000067
+ 0x0000000b 0x0000006f
+
+ 0x00010000 0x0000001b
+ 0x00010001 0x00000023
+ 0x00010002 0x0000002b
+ 0x00010003 0x00000033
+ 0x00010004 0x0000003b
+ 0x00010005 0x00000043
+ 0x00010006 0x0000004b
+ 0x00010007 0x00000055
+ 0x00010008 0x0000005d
+ 0x00010009 0x00000067
+ 0x0001000a 0x00000070
+
+ 0x00020000 0x00000017
+ 0x00020001 0x00000023
+ 0x00020002 0x0000002d
+ 0x00020003 0x00000037
+ 0x00020004 0x00000041
+ 0x00020005 0x0000004b
+ 0x00020006 0x00000057
+ 0x00020007 0x00000063
+ 0x00020008 0x0000006f
+
+ 0x00030000 0x00000015
+ 0x00030001 0x00000021
+ 0x00030002 0x0000002d
+ 0x00030003 0x00000039
+ 0x00030004 0x00000045
+ 0x00030005 0x00000053
+ 0x00030006 0x0000005f
+ 0x00030007 0x00000071>;
+ #thermal-sensor-cells = <1>;
+ };
+
wdog1: watchdog@30280000 {
compatible = "fsl,imx8mq-wdt", "fsl,imx21-wdt";
reg = <0x30280000 0x10000>;
status = "disabled";
};
+ sdma2: sdma@302c0000 {
+ compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma";
+ reg = <0x302c0000 0x10000>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_SDMA2_ROOT>,
+ <&clk IMX8MQ_CLK_SDMA2_ROOT>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
+ };
+
iomuxc: iomuxc@30330000 {
compatible = "fsl,imx8mq-iomuxc";
reg = <0x30330000 0x10000>;
};
iomuxc_gpr: syscon@30340000 {
- compatible = "fsl,imx8mq-iomuxc-gpr", "syscon";
+ compatible = "fsl,imx8mq-iomuxc-gpr", "fsl,imx6q-iomuxc-gpr", "syscon";
reg = <0x30340000 0x10000>;
};
+ ocotp: ocotp-ctrl@30350000 {
+ compatible = "fsl,imx8mq-ocotp", "syscon";
+ reg = <0x30350000 0x10000>;
+ clocks = <&clk IMX8MQ_CLK_OCOTP_ROOT>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
anatop: syscon@30360000 {
compatible = "fsl,imx8mq-anatop", "syscon";
reg = <0x30360000 0x10000>;
"clk_ext3", "clk_ext4";
};
+ src: reset-controller@30390000 {
+ compatible = "fsl,imx8mq-src", "syscon";
+ reg = <0x30390000 0x10000>;
+ #reset-cells = <1>;
+ };
+
gpc: gpc@303a0000 {
compatible = "fsl,imx8mq-gpc";
reg = <0x303a0000 0x10000>;
reg = <IMX8M_POWER_DOMAIN_MIPI>;
};
- pgc_pcie1: power-domain@1 {
+ /*
+ * As per comment in ATF source code:
+ *
+ * PCIE1 and PCIE2 share the
+ * same reset signal, if we
+ * power down PCIE2, PCIE1
+ * will be held in reset too.
+ *
+ * So instead of creating two
+ * separate power domains for
+ * PCIE1 and PCIE2 we create a
+ * link between both and use
+ * it as a shared PCIE power
+ * domain.
+ */
+ pgc_pcie: power-domain@1 {
#power-domain-cells = <0>;
reg = <IMX8M_POWER_DOMAIN_PCIE1>;
+ power-domains = <&pgc_pcie2>;
};
pgc_otg1: power-domain@2 {
status = "disabled";
};
+ sai2: sai@308b0000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx8mq-sai",
+ "fsl,imx6sx-sai";
+ reg = <0x308b0000 0x10000>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_SAI2_IPG>,
+ <&clk IMX8MQ_CLK_SAI2_ROOT>,
+ <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma1 10 24 0>, <&sdma1 11 24 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
i2c1: i2c@30a20000 {
compatible = "fsl,imx8mq-i2c", "fsl,imx21-i2c";
reg = <0x30a20000 0x10000>;
status = "disabled";
};
+ sdma1: sdma@30bd0000 {
+ compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma";
+ reg = <0x30bd0000 0x10000>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_SDMA1_ROOT>,
+ <&clk IMX8MQ_CLK_AHB>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
+ };
+
fec1: ethernet@30be0000 {
compatible = "fsl,imx8mq-fec", "fsl,imx6sx-fec";
reg = <0x30be0000 0x10000>;
};
};
+ gpu: gpu@38000000 {
+ compatible = "vivante,gc";
+ reg = <0x38000000 0x40000>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_GPU_ROOT>,
+ <&clk IMX8MQ_CLK_GPU_SHADER_DIV>,
+ <&clk IMX8MQ_CLK_GPU_AXI>,
+ <&clk IMX8MQ_CLK_GPU_AHB>;
+ clock-names = "core", "shader", "bus", "reg";
+ assigned-clocks = <&clk IMX8MQ_CLK_GPU_CORE_SRC>,
+ <&clk IMX8MQ_CLK_GPU_SHADER_SRC>,
+ <&clk IMX8MQ_CLK_GPU_AXI>,
+ <&clk IMX8MQ_CLK_GPU_AHB>,
+ <&clk IMX8MQ_GPU_PLL_BYPASS>;
+ assigned-clock-parents = <&clk IMX8MQ_GPU_PLL_OUT>,
+ <&clk IMX8MQ_GPU_PLL_OUT>,
+ <&clk IMX8MQ_GPU_PLL_OUT>,
+ <&clk IMX8MQ_GPU_PLL_OUT>,
+ <&clk IMX8MQ_GPU_PLL>;
+ assigned-clock-rates = <800000000>, <800000000>,
+ <800000000>, <800000000>, <0>;
+ power-domains = <&pgc_gpu>;
+ };
+
usb_dwc3_0: usb@38100000 {
compatible = "fsl,imx8mq-dwc3", "snps,dwc3";
reg = <0x38100000 0x10000>;
status = "disabled";
};
+
+ pcie0: pcie@33800000 {
+ compatible = "fsl,imx8mq-pcie";
+ reg = <0x33800000 0x400000>,
+ <0x1ff00000 0x80000>;
+ reg-names = "dbi", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ bus-range = <0x00 0xff>;
+ ranges = <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000 /* downstream I/O 64KB */
+ 0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */
+ num-lanes = <1>;
+ num-viewport = <4>;
+ interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &gic GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &gic GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &gic GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &gic GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,max-link-speed = <2>;
+ power-domains = <&pgc_pcie>;
+ resets = <&src IMX8MQ_RESET_PCIEPHY>,
+ <&src IMX8MQ_RESET_PCIE_CTRL_APPS_EN>,
+ <&src IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF>;
+ reset-names = "pciephy", "apps", "turnoff";
+ status = "disabled";
+ };
+
+ pcie1: pcie@33c00000 {
+ compatible = "fsl,imx8mq-pcie";
+ reg = <0x33c00000 0x400000>,
+ <0x27f00000 0x80000>;
+ reg-names = "dbi", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0x00000000 0x27f80000 0 0x00010000 /* downstream I/O 64KB */
+ 0x82000000 0 0x20000000 0x20000000 0 0x07f00000>; /* non-prefetchable memory */
+ num-lanes = <1>;
+ num-viewport = <4>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &gic GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &gic GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &gic GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,max-link-speed = <2>;
+ power-domains = <&pgc_pcie>;
+ resets = <&src IMX8MQ_RESET_PCIEPHY2>,
+ <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_EN>,
+ <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF>;
+ reset-names = "pciephy", "apps", "turnoff";
+ status = "disabled";
+ };
+
gic: interrupt-controller@38800000 {
compatible = "arm,gic-v3";
reg = <0x38800000 0x10000>, /* GIC Dist */
};
};
+&adma_i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c1 &pinctrl_ioexp_rst>;
+ status = "okay";
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9646", "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+ reset-gpios = <&lsio_gpio1 1 GPIO_ACTIVE_LOW>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ max7322: gpio@68 {
+ compatible = "maxim,max7322";
+ reg = <0x68>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ pressure-sensor@60 {
+ compatible = "fsl,mpl3115";
+ reg = <0x60>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ pca9557_a: gpio@1a {
+ compatible = "nxp,pca9557";
+ reg = <0x1a>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9557_b: gpio@1d {
+ compatible = "nxp,pca9557";
+ reg = <0x1d>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ light-sensor@44 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isl29023>;
+ compatible = "isil,isl29023";
+ reg = <0x44>;
+ interrupt-parent = <&lsio_gpio1>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };
+ };
+};
+
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
>;
};
+ pinctrl_ioexp_rst: ioexp_rst_grp {
+ fsl,pins = <
+ IMX8QXP_SPI2_SDO_LSIO_GPIO1_IO01 0x06000021
+ >;
+ };
+
+ pinctrl_isl29023: isl29023grp {
+ fsl,pins = <
+ IMX8QXP_SPI2_SDI_LSIO_GPIO1_IO02 0x00000021
+ >;
+ };
+
+ pinctrl_lpi2c1: lpi2c1grp {
+ fsl,pins = <
+ IMX8QXP_USB_SS3_TC1_ADMA_I2C1_SCL 0x06000021
+ IMX8QXP_USB_SS3_TC3_ADMA_I2C1_SDA 0x06000021
+ >;
+ };
+
pinctrl_lpuart0: lpuart0grp {
fsl,pins = <
IMX8QXP_UART0_RX_ADMA_UART0_RX 0x06000020
mmc1 = &usdhc2;
mmc2 = &usdhc3;
serial0 = &adma_lpuart0;
+ mu1 = &lsio_mu1;
};
cpus {
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&A35_L2>;
+ clocks = <&clk IMX_A35_CLK>;
+ operating-points-v2 = <&a35_opp_table>;
+ #cooling-cells = <2>;
};
A35_1: cpu@1 {
reg = <0x0 0x1>;
enable-method = "psci";
next-level-cache = <&A35_L2>;
+ clocks = <&clk IMX_A35_CLK>;
+ operating-points-v2 = <&a35_opp_table>;
+ #cooling-cells = <2>;
};
A35_2: cpu@2 {
reg = <0x0 0x2>;
enable-method = "psci";
next-level-cache = <&A35_L2>;
+ clocks = <&clk IMX_A35_CLK>;
+ operating-points-v2 = <&a35_opp_table>;
+ #cooling-cells = <2>;
};
A35_3: cpu@3 {
reg = <0x0 0x3>;
enable-method = "psci";
next-level-cache = <&A35_L2>;
+ clocks = <&clk IMX_A35_CLK>;
+ operating-points-v2 = <&a35_opp_table>;
+ #cooling-cells = <2>;
};
A35_L2: l2-cache0 {
};
};
+ a35_opp_table: opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-900000000 {
+ opp-hz = /bits/ 64 <900000000>;
+ opp-microvolt = <1000000>;
+ clock-latency-ns = <150000>;
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1100000>;
+ clock-latency-ns = <150000>;
+ opp-suspend;
+ };
+ };
+
gic: interrupt-controller@51a00000 {
compatible = "arm,gic-v3";
reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */
scu {
compatible = "fsl,imx-scu";
mbox-names = "tx0", "tx1", "tx2", "tx3",
- "rx0", "rx1", "rx2", "rx3";
+ "rx0", "rx1", "rx2", "rx3",
+ "gip3";
mboxes = <&lsio_mu1 0 0
&lsio_mu1 0 1
&lsio_mu1 0 2
&lsio_mu1 1 0
&lsio_mu1 1 1
&lsio_mu1 1 2
- &lsio_mu1 1 3>;
+ &lsio_mu1 1 3
+ &lsio_mu1 3 3>;
clk: clock-controller {
compatible = "fsl,imx8qxp-clk";
status = "disabled";
};
+ adma_lpuart1: serial@5a070000 {
+ compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+ reg = <0x5a070000 0x1000>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ clocks = <&adma_lpcg IMX_ADMA_LPCG_UART1_BAUD_CLK>;
+ clock-names = "ipg";
+ power-domains = <&pd IMX_SC_R_UART_1>;
+ status = "disabled";
+ };
+
+ adma_lpuart2: serial@5a080000 {
+ compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+ reg = <0x5a080000 0x1000>;
+ interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ clocks = <&adma_lpcg IMX_ADMA_LPCG_UART2_BAUD_CLK>;
+ clock-names = "ipg";
+ power-domains = <&pd IMX_SC_R_UART_2>;
+ status = "disabled";
+ };
+
+ adma_lpuart3: serial@5a090000 {
+ compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+ reg = <0x5a090000 0x1000>;
+ interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ clocks = <&adma_lpcg IMX_ADMA_LPCG_UART3_BAUD_CLK>;
+ clock-names = "ipg";
+ power-domains = <&pd IMX_SC_R_UART_3>;
+ status = "disabled";
+ };
+
adma_i2c0: i2c@5a800000 {
compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
reg = <0x5a800000 0x4000>;
compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
reg = <0x5d1b0000 0x10000>;
interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
- #mbox-cells = <0>;
+ #mbox-cells = <2>;
status = "disabled";
};
#mbox-cells = <2>;
};
+ lsio_mu2: mailbox@5d1d0000 {
+ compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+ reg = <0x5d1d0000 0x10000>;
+ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
lsio_mu3: mailbox@5d1e0000 {
compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
reg = <0x5d1e0000 0x10000>;
interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
- #mbox-cells = <0>;
+ #mbox-cells = <2>;
status = "disabled";
};
compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
reg = <0x5d1f0000 0x10000>;
interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
- #mbox-cells = <0>;
+ #mbox-cells = <2>;
status = "disabled";
};
power-domains = <&pd IMX_SC_R_GPIO_7>;
};
};
+
+ watchdog {
+ compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt";
+ timeout-sec = <60>;
+ };
};
projects / platform / kernel / linux-starfive.git / commitdiff