- #gpio-cells : Should be two. The first cell is the pin number and
the second cell is used to specify flags.
See ../../gpio/gpio.txt for more information.
-- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of
+- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of
the cell formats.
- clock-names: should be "refclk"
- pinctrl-0: should contain the pinctrl states described by pinctrl
default.
- #pwm-cells: should be set to 3. This PWM chip use the default 3 cells
- bindings defined in pwm.txt in this directory.
+ bindings defined in pwm.yaml in this directory.
Example:
- "atmel,sama5d2-pwm"
- "microchip,sam9x60-pwm"
- reg: physical base address and length of the controller's registers
- - #pwm-cells: Should be 3. See pwm.txt in this directory for a
+ - #pwm-cells: Should be 3. See pwm.yaml in this directory for a
description of the cells format.
Example:
Required properties:
- compatible: should be "atmel,tcb-pwm"
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The only third cell flag supported by this binding is
PWM_POLARITY_INVERTED.
- tc-block: The Timer Counter block to use as a PWM chip.
- compatible: must be "brcm,bcm7038-pwm"
- reg: physical base address and length for this controller
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description
of the cells format
- clocks: a phandle to the reference clock for this block which is fed through
its internal variable clock frequency generator
- compatible: must be "brcm,iproc-pwm"
- reg: physical base address and length of the controller's registers
- clocks: phandle + clock specifier pair for the external clock
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a
description of the cells format.
Refer to clocks/clock-bindings.txt for generic clock consumer properties.
- compatible: should contain "brcm,kona-pwm"
- reg: physical base address and length of the controller's registers
- clocks: phandle + clock specifier pair for the external clock
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a
description of the cells format.
Refer to clocks/clock-bindings.txt for generic clock consumer properties.
- clock-names: Must include the following entries.
- pwm: PWM operating clock.
- sys: PWM system interface clock.
- - #pwm-cells: Should be 2. See pwm.txt in this directory for the
+ - #pwm-cells: Should be 2. See pwm.yaml in this directory for the
description of the cells format.
- img,cr-periph: Must contain a phandle to the peripheral control
syscon node which contains PWM control registers.
- "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1
- "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27
- reg: physical base address and length of the controller's registers
-- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.txt
+- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.yaml
in this directory for a description of the cells format.
- clocks : Clock specifiers for both ipg and per clocks.
- clock-names : Clock names should include both "ipg" and "per"
Required properties:
- compatible : Should be "fsl,imx7ulp-pwm".
- reg: Physical base address and length of the controller's registers.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format.
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format.
- clocks : The clock provided by the SoC to drive the PWM.
- interrupts: The interrupt for the PWM controller.
See ../clock/clock-bindings.txt for details.
- clock-names: Must include the following entries.
- pwm: PWM operating clock.
- - #pwm-cells: Should be 3. See pwm.txt in this directory for the description
+ - #pwm-cells: Should be 3. See pwm.yaml in this directory for the description
of the cells format.
Example:
Required properties:
- compatible: should be "fsl,imx23-pwm"
- reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
- fsl,pwm-number: the number of PWM devices
- "nvidia,tegra210-pwm", "nvidia,tegra20-pwm": for Tegra210
- "nvidia,tegra186-pwm": for Tegra186
- reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
Required properties:
- compatible: "nxp,pca9685-pwm"
- - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of
+ - #pwm-cells: Should be 2. See pwm.yaml in this directory for a description of
the cells format.
The index 16 is the ALLCALL channel, that sets all PWM channels at the same
time.
- clocks: This clock defines the base clock frequency of the PWM hardware
system, the period and the duty_cycle of the PWM signal is a multiple of
the base period.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Examples:
- compatible: should be "marvell,berlin-pwm"
- reg: physical base address and length of the controller's registers
- clocks: phandle to the input clock
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format.
Example:
- "fsl,vf610-ftm-pwm" for PWM compatible with the one integrated on VF610
- "fsl,imx8qm-ftm-pwm" for PWM compatible with the one integrated on i.MX8QM
- reg: Physical base address and length of the controller's registers
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
- clock-names: Should include the following module clock source entries:
"ftm_sys" (module clock, also can be used as counter clock),
- reg: physical base address and length of the controller's registers.
- clocks: phandle and clock specifier of the PWM reference clock.
- resets: phandle and reset specifier for the PWM controller reset.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Example:
Required properties:
- compatible: "ti,lp3943-pwm"
- - #pwm-cells: Should be 2. See pwm.txt in this directory for a
+ - #pwm-cells: Should be 2. See pwm.yaml in this directory for a
description of the cells format.
Note that this hardware limits the period length to the
range 6250~1600000.
- "mediatek,mt7629-pwm", "mediatek,mt7622-pwm": found on mt7629 SoC.
- "mediatek,mt8516-pwm": found on mt8516 SoC.
- reg: physical base address and length of the controller's registers.
- - #pwm-cells: must be 2. See pwm.txt in this directory for a description of
+ - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of
the cell format.
- clocks: phandle and clock specifier of the PWM reference clock.
- clock-names: must contain the following, except for MT7628 which
or "amlogic,meson-g12a-ee-pwm"
or "amlogic,meson-g12a-ao-pwm-ab"
or "amlogic,meson-g12a-ao-pwm-cd"
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Optional properties:
- "mediatek,mt6595-disp-pwm": found on mt6595 SoC.
- "mediatek,mt8173-disp-pwm": found on mt8173 SoC.
- reg: physical base address and length of the controller's registers.
- - #pwm-cells: must be 2. See pwm.txt in this directory for a description of
+ - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of
the cell format.
- clocks: phandle and clock specifier of the PWM reference clock.
- clock-names: must contain the following:
- compatible: Shall contain "ti,omap-dmtimer-pwm".
- ti,timers: phandle to PWM capable OMAP timer. See timer/ti,timer.txt for info
about these timers.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Optional properties:
- For newer hardware (rk3328 and future socs): specified by name
- "pwm": This is used to derive the functional clock.
- "pclk": This is the APB bus clock.
- - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory
+ - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.yaml in this directory
for a description of the cell format.
Example:
Please refer to sifive-blocks-ip-versioning.txt for details.
- reg: physical base address and length of the controller's registers
- clocks: Should contain a clock identifier for the PWM's parent clock.
-- #pwm-cells: Should be 3. See pwm.txt in this directory
+- #pwm-cells: Should be 3. See pwm.yaml in this directory
for a description of the cell format.
- interrupts: one interrupt per PWM channel
- clock-names: Should contain following entries:
"pwmn": used to derive the functional clock for PWM channel n (n range: 0 ~ 3).
"enablen": for PWM channel n enable clock (n range: 0 ~ 3).
-- #pwm-cells: Should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 2. See pwm.yaml in this directory for a description of
the cells format.
Optional properties:
Required parameters:
- compatible: Must be "st,stm32-pwm-lp".
- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells
- bindings defined in pwm.txt.
+ bindings defined in pwm.yaml.
Optional properties:
- pinctrl-names: Set to "default". An additional "sleep" state can be
for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap";
for 66ak2g - compatible = "ti,k2g-ecap", "ti,am3352-ecap";
for am654 - compatible = "ti,am654-ecap", "ti,am3352-ecap";
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The PWM channel index ranges from 0 to 4. The only third
cell flag supported by this binding is PWM_POLARITY_INVERTED.
- reg: physical base address and size of the registers map.
for am654 - compatible = "ti,am654-ehrpwm", "ti-am3352-ehrpwm";
for da850 - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
for dra746 - compatible = "ti,dra746-ehrpwm", "ti-am3352-ehrpwm";
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The only third cell flag supported by this binding is
PWM_POLARITY_INVERTED.
- reg: physical base address and size of the registers map.
- clock-names: "pclk" for PCLK, "wclk" for WCLK to the PWM controller. The
PCLK is for register access, while WCLK is the reference clock for
calculating period and duty cycles.
- - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+ - #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Example:
2) PWM controller nodes
-----------------------
-PWM controller nodes must specify the number of cells used for the
-specifier using the '#pwm-cells' property.
-
-An example PWM controller might look like this:
-
- pwm: pwm@7000a000 {
- compatible = "nvidia,tegra20-pwm";
- reg = <0x7000a000 0x100>;
- #pwm-cells = <2>;
- };
+See pwm.yaml.
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/pwm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PWM controllers (providers)
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+
+properties:
+ $nodename:
+ pattern: "^pwm(@.*|-[0-9a-f])*$"
+
+ "#pwm-cells":
+ description:
+ Number of cells in a PWM specifier.
+
+required:
+ - "#pwm-cells"
+
+examples:
+ - |
+ pwm: pwm@7000a000 {
+ compatible = "nvidia,tegra20-pwm";
+ reg = <0x7000a000 0x100>;
+ #pwm-cells = <2>;
+ };
maxItems: 1
'#pwm-cells':
- # should be 2. See pwm.txt in this directory for a description of
+ # should be 2. See pwm.yaml in this directory for a description of
# the cells format.
const: 2
maxItems: 1
'#pwm-cells':
- # should be 3. See pwm.txt in this directory for a description of
+ # should be 3. See pwm.yaml in this directory for a description of
# the cells format. The only third cell flag supported by this binding is
# PWM_POLARITY_INVERTED.
const: 3
- "st,spear320-pwm"
- "st,spear1340-pwm"
- reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
Example:
Required properties:
- compatible: should be:
- "st,stmpe-pwm"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
Example:
Required properties:
- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
Example:
Required properties:
- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
Example:
Required properties:
- compatible: should be "via,vt8500-pwm"
- reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The only third cell flag supported by this binding is
PWM_POLARITY_INVERTED.
- clocks: phandle to the PWM source clock
- compatible: Must be one of:
* ingenic,jz4740-pwm
* ingenic,jz4725b-pwm
-- #pwm-cells: Should be 3. See ../pwm/pwm.txt for a description of the cell
+- #pwm-cells: Should be 3. See ../pwm/pwm.yaml for a description of the cell
format.
- clocks: List of phandle & clock specifiers for the TCU clocks.
- clock-names: List of name strings for the TCU clocks.
projects / platform / kernel / linux-starfive.git / commitdiff