arm64: dts: ti: j721e-common-proc-board: Add uart pinmux

Explicitly define the pinmux rather than depend on bootloader configured
pinmux for the platform.

Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 8433637..fa90943 100644 (file)
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -174,6 +174,36 @@
 };
 
 &main_pmx0 {
+       main_uart0_pins_default: main-uart0-pins-default {
+               pinctrl-single,pins = <
+                       J721E_IOPAD(0x1d4, PIN_INPUT, 1) /* (Y3) SPI1_CS0.UART0_CTSn */
+                       J721E_IOPAD(0x1c0, PIN_OUTPUT, 1) /* (AA2) SPI0_CS0.UART0_RTSn */
+                       J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
+                       J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
+               >;
+       };
+
+       main_uart1_pins_default: main-uart1-pins-default {
+               pinctrl-single,pins = <
+                       J721E_IOPAD(0x1f8, PIN_INPUT, 0) /* (AA4) UART1_RXD */
+                       J721E_IOPAD(0x1fc, PIN_OUTPUT, 0) /* (AB4) UART1_TXD */
+               >;
+       };
+
+       main_uart2_pins_default: main-uart2-pins-default {
+               pinctrl-single,pins = <
+                       J721E_IOPAD(0x1dc, PIN_INPUT, 3) /* (Y1) SPI1_CLK.UART2_RXD */
+                       J721E_IOPAD(0x1e0, PIN_OUTPUT, 3) /* (Y5) SPI1_D0.UART2_TXD */
+               >;
+       };
+
+       main_uart4_pins_default: main-uart4-pins-default {
+               pinctrl-single,pins = <
+                       J721E_IOPAD(0x190, PIN_INPUT, 1) /* (W23) RGMII6_TD3.UART4_RXD */
+                       J721E_IOPAD(0x194, PIN_OUTPUT, 1) /* (W28) RGMII6_TD2.UART4_TXD */
+               >;
+       };
+
        sw10_button_pins_default: sw10-button-pins-default {
                pinctrl-single,pins = <
                        J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
@@ -295,6 +325,22 @@
 };
 
 &wkup_pmx0 {
+       wkup_uart0_pins_default: wkup-uart0-pins-default {
+               pinctrl-single,pins = <
+                       J721E_WKUP_IOPAD(0xa0, PIN_INPUT, 0) /* (J29) WKUP_UART0_RXD */
+                       J721E_WKUP_IOPAD(0xa4, PIN_OUTPUT, 0) /* (J28) WKUP_UART0_TXD */
+               >;
+       };
+
+       mcu_uart0_pins_default: mcu-uart0-pins-default {
+               pinctrl-single,pins = <
+                       J721E_WKUP_IOPAD(0xe8, PIN_INPUT, 0) /* (H29) WKUP_GPIO0_14.MCU_UART0_CTSn */
+                       J721E_WKUP_IOPAD(0xec, PIN_OUTPUT, 0) /* (J27) WKUP_GPIO0_15.MCU_UART0_RTSn */
+                       J721E_WKUP_IOPAD(0xe4, PIN_INPUT, 0) /* (H28) WKUP_GPIO0_13.MCU_UART0_RXD */
+                       J721E_WKUP_IOPAD(0xe0, PIN_OUTPUT, 0) /* (G29) WKUP_GPIO0_12.MCU_UART0_TXD */
+               >;
+       };
+
        sw11_button_pins_default: sw11-button-pins-default {
                pinctrl-single,pins = <
                        J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
@@ -375,32 +421,40 @@
 &wkup_uart0 {
        /* Wakeup UART is used by System firmware */
        status = "reserved";
+       pinctrl-names = "default";
+       pinctrl-0 = <&wkup_uart0_pins_default>;
 };
 
 &mcu_uart0 {
        status = "okay";
-       /* Default pinmux */
+       pinctrl-names = "default";
+       pinctrl-0 = <&mcu_uart0_pins_default>;
 };
 
 &main_uart0 {
        status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&main_uart0_pins_default>;
        /* Shared with ATF on this platform */
        power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
 };
 
 &main_uart1 {
        status = "okay";
-       /* Default pinmux */
+       pinctrl-names = "default";
+       pinctrl-0 = <&main_uart1_pins_default>;
 };
 
 &main_uart2 {
        status = "okay";
-       /* Default pinmux */
+       pinctrl-names = "default";
+       pinctrl-0 = <&main_uart2_pins_default>;
 };
 
 &main_uart4 {
        status = "okay";
-       /* Default pinmux */
+       pinctrl-names = "default";
+       pinctrl-0 = <&main_uart4_pins_default>;
 };
 
 &main_gpio2 {