ETHTOOL_A_RSS_INDIR attribute returns RSS indrection table where each byte
indicates queue number.
+PLCA_GET_CFG
+============
+
+Gets the IEEE 802.3cg-2019 Clause 148 Physical Layer Collision Avoidance
+(PLCA) Reconciliation Sublayer (RS) attributes.
+
+Request contents:
+
+ ===================================== ====== ==========================
+ ``ETHTOOL_A_PLCA_HEADER`` nested request header
+ ===================================== ====== ==========================
+
+Kernel response contents:
+
+ ====================================== ====== =============================
+ ``ETHTOOL_A_PLCA_HEADER`` nested reply header
+ ``ETHTOOL_A_PLCA_VERSION`` u16 Supported PLCA management
+ interface standard/version
+ ``ETHTOOL_A_PLCA_ENABLED`` u8 PLCA Admin State
+ ``ETHTOOL_A_PLCA_NODE_ID`` u32 PLCA unique local node ID
+ ``ETHTOOL_A_PLCA_NODE_CNT`` u32 Number of PLCA nodes on the
+ network, including the
+ coordinator
+ ``ETHTOOL_A_PLCA_TO_TMR`` u32 Transmit Opportunity Timer
+ value in bit-times (BT)
+ ``ETHTOOL_A_PLCA_BURST_CNT`` u32 Number of additional packets
+ the node is allowed to send
+ within a single TO
+ ``ETHTOOL_A_PLCA_BURST_TMR`` u32 Time to wait for the MAC to
+ transmit a new frame before
+ terminating the burst
+ ====================================== ====== =============================
+
+When set, the optional ``ETHTOOL_A_PLCA_VERSION`` attribute indicates which
+standard and version the PLCA management interface complies to. When not set,
+the interface is vendor-specific and (possibly) supplied by the driver.
+The OPEN Alliance SIG specifies a standard register map for 10BASE-T1S PHYs
+embedding the PLCA Reconcialiation Sublayer. See "10BASE-T1S PLCA Management
+Registers" at https://www.opensig.org/about/specifications/.
+
+When set, the optional ``ETHTOOL_A_PLCA_ENABLED`` attribute indicates the
+administrative state of the PLCA RS. When not set, the node operates in "plain"
+CSMA/CD mode. This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.1
+aPLCAAdminState / 30.16.1.2.1 acPLCAAdminControl.
+
+When set, the optional ``ETHTOOL_A_PLCA_NODE_ID`` attribute indicates the
+configured local node ID of the PHY. This ID determines which transmit
+opportunity (TO) is reserved for the node to transmit into. This option is
+corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.4 aPLCALocalNodeID. The valid
+range for this attribute is [0 .. 255] where 255 means "not configured".
+
+When set, the optional ``ETHTOOL_A_PLCA_NODE_CNT`` attribute indicates the
+configured maximum number of PLCA nodes on the mixing-segment. This number
+determines the total number of transmit opportunities generated during a
+PLCA cycle. This attribute is relevant only for the PLCA coordinator, which is
+the node with aPLCALocalNodeID set to 0. Follower nodes ignore this setting.
+This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.3
+aPLCANodeCount. The valid range for this attribute is [1 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_TO_TMR`` attribute indicates the
+configured value of the transmit opportunity timer in bit-times. This value
+must be set equal across all nodes sharing the medium for PLCA to work
+correctly. This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.5
+aPLCATransmitOpportunityTimer. The valid range for this attribute is
+[0 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_BURST_CNT`` attribute indicates the
+configured number of extra packets that the node is allowed to send during a
+single transmit opportunity. By default, this attribute is 0, meaning that
+the node can only send a sigle frame per TO. When greater than 0, the PLCA RS
+keeps the TO after any transmission, waiting for the MAC to send a new frame
+for up to aPLCABurstTimer BTs. This can only happen a number of times per PLCA
+cycle up to the value of this parameter. After that, the burst is over and the
+normal counting of TOs resumes. This option is corresponding to
+``IEEE 802.3cg-2019`` 30.16.1.1.6 aPLCAMaxBurstCount. The valid range for this
+attribute is [0 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_BURST_TMR`` attribute indicates how
+many bit-times the PLCA RS waits for the MAC to initiate a new transmission
+when aPLCAMaxBurstCount is greater than 0. If the MAC fails to send a new
+frame within this time, the burst ends and the counting of TOs resumes.
+Otherwise, the new frame is sent as part of the current burst. This option
+is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.7 aPLCABurstTimer. The
+valid range for this attribute is [0 .. 255]. Although, the value should be
+set greater than the Inter-Frame-Gap (IFG) time of the MAC (plus some margin)
+for PLCA burst mode to work as intended.
+
+PLCA_SET_CFG
+============
+
+Sets PLCA RS parameters.
+
+Request contents:
+
+ ====================================== ====== =============================
+ ``ETHTOOL_A_PLCA_HEADER`` nested request header
+ ``ETHTOOL_A_PLCA_ENABLED`` u8 PLCA Admin State
+ ``ETHTOOL_A_PLCA_NODE_ID`` u8 PLCA unique local node ID
+ ``ETHTOOL_A_PLCA_NODE_CNT`` u8 Number of PLCA nodes on the
+ netkork, including the
+ coordinator
+ ``ETHTOOL_A_PLCA_TO_TMR`` u8 Transmit Opportunity Timer
+ value in bit-times (BT)
+ ``ETHTOOL_A_PLCA_BURST_CNT`` u8 Number of additional packets
+ the node is allowed to send
+ within a single TO
+ ``ETHTOOL_A_PLCA_BURST_TMR`` u8 Time to wait for the MAC to
+ transmit a new frame before
+ terminating the burst
+ ====================================== ====== =============================
+
+For a description of each attribute, see ``PLCA_GET_CFG``.
+
+PLCA_GET_STATUS
+===============
+
+Gets PLCA RS status information.
+
+Request contents:
+
+ ===================================== ====== ==========================
+ ``ETHTOOL_A_PLCA_HEADER`` nested request header
+ ===================================== ====== ==========================
+
+Kernel response contents:
+
+ ====================================== ====== =============================
+ ``ETHTOOL_A_PLCA_HEADER`` nested reply header
+ ``ETHTOOL_A_PLCA_STATUS`` u8 PLCA RS operational status
+ ====================================== ====== =============================
+
+When set, the ``ETHTOOL_A_PLCA_STATUS`` attribute indicates whether the node is
+detecting the presence of the BEACON on the network. This flag is
+corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.2 aPLCAStatus.
+
Request translation
===================
n/a ``ETHTOOL_MSG_PHC_VCLOCKS_GET``
n/a ``ETHTOOL_MSG_MODULE_GET``
n/a ``ETHTOOL_MSG_MODULE_SET``
+ n/a ``ETHTOOL_MSG_PLCA_GET_CFG``
+ n/a ``ETHTOOL_MSG_PLCA_SET_CFG``
+ n/a ``ETHTOOL_MSG_PLCA_GET_STATUS``
=================================== =====================================
F: Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.yaml
F: drivers/iio/chemical/pms7003.c
+PLCA RECONCILIATION SUBLAYER (IEEE802.3 Clause 148)
+M: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
+L: netdev@vger.kernel.org
+S: Maintained
+F: net/ethtool/plca.c
+
PLDMFW LIBRARY
M: Jacob Keller <jacob.e.keller@intel.com>
S: Maintained
struct phy_device;
struct phy_tdr_config;
+struct phy_plca_cfg;
+struct phy_plca_status;
/**
* struct ethtool_phy_ops - Optional PHY device options
* @get_sset_count: Get number of strings that @get_strings will write.
* @get_strings: Return a set of strings that describe the requested objects
* @get_stats: Return extended statistics about the PHY device.
+ * @get_plca_cfg: Return PLCA configuration.
+ * @set_plca_cfg: Set PLCA configuration.
+ * @get_plca_status: Get PLCA configuration.
* @start_cable_test: Start a cable test
* @start_cable_test_tdr: Start a Time Domain Reflectometry cable test
*
int (*get_strings)(struct phy_device *dev, u8 *data);
int (*get_stats)(struct phy_device *dev,
struct ethtool_stats *stats, u64 *data);
+ int (*get_plca_cfg)(struct phy_device *dev,
+ struct phy_plca_cfg *plca_cfg);
+ int (*set_plca_cfg)(struct phy_device *dev,
+ const struct phy_plca_cfg *plca_cfg,
+ struct netlink_ext_ack *extack);
+ int (*get_plca_status)(struct phy_device *dev,
+ struct phy_plca_status *plca_st);
int (*start_cable_test)(struct phy_device *phydev,
struct netlink_ext_ack *extack);
int (*start_cable_test_tdr)(struct phy_device *phydev,
#define PHY_PAIR_ALL -1
/**
+ * struct phy_plca_cfg - Configuration of the PLCA (Physical Layer Collision
+ * Avoidance) Reconciliation Sublayer.
+ *
+ * @version: read-only PLCA register map version. -1 = not available. Ignored
+ * when setting the configuration. Format is the same as reported by the PLCA
+ * IDVER register (31.CA00). -1 = not available.
+ * @enabled: PLCA configured mode (enabled/disabled). -1 = not available / don't
+ * set. 0 = disabled, anything else = enabled.
+ * @node_id: the PLCA local node identifier. -1 = not available / don't set.
+ * Allowed values [0 .. 254]. 255 = node disabled.
+ * @node_cnt: the PLCA node count (maximum number of nodes having a TO). Only
+ * meaningful for the coordinator (node_id = 0). -1 = not available / don't
+ * set. Allowed values [1 .. 255].
+ * @to_tmr: The value of the PLCA to_timer in bit-times, which determines the
+ * PLCA transmit opportunity window opening. See IEEE802.3 Clause 148 for
+ * more details. The to_timer shall be set equal over all nodes.
+ * -1 = not available / don't set. Allowed values [0 .. 255].
+ * @burst_cnt: controls how many additional frames a node is allowed to send in
+ * single transmit opportunity (TO). The default value of 0 means that the
+ * node is allowed exactly one frame per TO. A value of 1 allows two frames
+ * per TO, and so on. -1 = not available / don't set.
+ * Allowed values [0 .. 255].
+ * @burst_tmr: controls how many bit times to wait for the MAC to send a new
+ * frame before interrupting the burst. This value should be set to a value
+ * greater than the MAC inter-packet gap (which is typically 96 bits).
+ * -1 = not available / don't set. Allowed values [0 .. 255].
+ *
+ * A structure containing configuration parameters for setting/getting the PLCA
+ * RS configuration. The driver does not need to implement all the parameters,
+ * but should report what is actually used.
+ */
+struct phy_plca_cfg {
+ int version;
+ int enabled;
+ int node_id;
+ int node_cnt;
+ int to_tmr;
+ int burst_cnt;
+ int burst_tmr;
+};
+
+/**
+ * struct phy_plca_status - Status of the PLCA (Physical Layer Collision
+ * Avoidance) Reconciliation Sublayer.
+ *
+ * @pst: The PLCA status as reported by the PST bit in the PLCA STATUS
+ * register(31.CA03), indicating BEACON activity.
+ *
+ * A structure containing status information of the PLCA RS configuration.
+ * The driver does not need to implement all the parameters, but should report
+ * what is actually used.
+ */
+struct phy_plca_status {
+ bool pst;
+};
+
+/**
* struct phy_driver - Driver structure for a particular PHY type
*
* @mdiodrv: Data common to all MDIO devices
ETHTOOL_MSG_PSE_GET,
ETHTOOL_MSG_PSE_SET,
ETHTOOL_MSG_RSS_GET,
+ ETHTOOL_MSG_PLCA_GET_CFG,
+ ETHTOOL_MSG_PLCA_SET_CFG,
+ ETHTOOL_MSG_PLCA_GET_STATUS,
/* add new constants above here */
__ETHTOOL_MSG_USER_CNT,
ETHTOOL_MSG_MODULE_NTF,
ETHTOOL_MSG_PSE_GET_REPLY,
ETHTOOL_MSG_RSS_GET_REPLY,
+ ETHTOOL_MSG_PLCA_GET_CFG_REPLY,
+ ETHTOOL_MSG_PLCA_GET_STATUS_REPLY,
+ ETHTOOL_MSG_PLCA_NTF,
/* add new constants above here */
__ETHTOOL_MSG_KERNEL_CNT,
ETHTOOL_A_RSS_MAX = (__ETHTOOL_A_RSS_CNT - 1),
};
+/* PLCA */
+
+enum {
+ ETHTOOL_A_PLCA_UNSPEC,
+ ETHTOOL_A_PLCA_HEADER, /* nest - _A_HEADER_* */
+ ETHTOOL_A_PLCA_VERSION, /* u16 */
+ ETHTOOL_A_PLCA_ENABLED, /* u8 */
+ ETHTOOL_A_PLCA_STATUS, /* u8 */
+ ETHTOOL_A_PLCA_NODE_CNT, /* u32 */
+ ETHTOOL_A_PLCA_NODE_ID, /* u32 */
+ ETHTOOL_A_PLCA_TO_TMR, /* u32 */
+ ETHTOOL_A_PLCA_BURST_CNT, /* u32 */
+ ETHTOOL_A_PLCA_BURST_TMR, /* u32 */
+
+ /* add new constants above here */
+ __ETHTOOL_A_PLCA_CNT,
+ ETHTOOL_A_PLCA_MAX = (__ETHTOOL_A_PLCA_CNT - 1)
+};
+
/* generic netlink info */
#define ETHTOOL_GENL_NAME "ethtool"
#define ETHTOOL_GENL_VERSION 1
linkstate.o debug.o wol.o features.o privflags.o rings.o \
channels.o coalesce.o pause.o eee.o tsinfo.o cabletest.o \
tunnels.o fec.o eeprom.o stats.o phc_vclocks.o module.o \
- pse-pd.o
+ pse-pd.o plca.o
[ETHTOOL_MSG_MODULE_GET] = ðnl_module_request_ops,
[ETHTOOL_MSG_PSE_GET] = ðnl_pse_request_ops,
[ETHTOOL_MSG_RSS_GET] = ðnl_rss_request_ops,
+ [ETHTOOL_MSG_PLCA_GET_CFG] = ðnl_plca_cfg_request_ops,
+ [ETHTOOL_MSG_PLCA_GET_STATUS] = ðnl_plca_status_request_ops,
};
static struct ethnl_dump_ctx *ethnl_dump_context(struct netlink_callback *cb)
[ETHTOOL_MSG_EEE_NTF] = ðnl_eee_request_ops,
[ETHTOOL_MSG_FEC_NTF] = ðnl_fec_request_ops,
[ETHTOOL_MSG_MODULE_NTF] = ðnl_module_request_ops,
+ [ETHTOOL_MSG_PLCA_NTF] = ðnl_plca_cfg_request_ops,
};
/* default notification handler */
[ETHTOOL_MSG_EEE_NTF] = ethnl_default_notify,
[ETHTOOL_MSG_FEC_NTF] = ethnl_default_notify,
[ETHTOOL_MSG_MODULE_NTF] = ethnl_default_notify,
+ [ETHTOOL_MSG_PLCA_NTF] = ethnl_default_notify,
};
void ethtool_notify(struct net_device *dev, unsigned int cmd, const void *data)
.policy = ethnl_rss_get_policy,
.maxattr = ARRAY_SIZE(ethnl_rss_get_policy) - 1,
},
+ {
+ .cmd = ETHTOOL_MSG_PLCA_GET_CFG,
+ .doit = ethnl_default_doit,
+ .start = ethnl_default_start,
+ .dumpit = ethnl_default_dumpit,
+ .done = ethnl_default_done,
+ .policy = ethnl_plca_get_cfg_policy,
+ .maxattr = ARRAY_SIZE(ethnl_plca_get_cfg_policy) - 1,
+ },
+ {
+ .cmd = ETHTOOL_MSG_PLCA_SET_CFG,
+ .flags = GENL_UNS_ADMIN_PERM,
+ .doit = ethnl_set_plca_cfg,
+ .policy = ethnl_plca_set_cfg_policy,
+ .maxattr = ARRAY_SIZE(ethnl_plca_set_cfg_policy) - 1,
+ },
+ {
+ .cmd = ETHTOOL_MSG_PLCA_GET_STATUS,
+ .doit = ethnl_default_doit,
+ .start = ethnl_default_start,
+ .dumpit = ethnl_default_dumpit,
+ .done = ethnl_default_done,
+ .policy = ethnl_plca_get_status_policy,
+ .maxattr = ARRAY_SIZE(ethnl_plca_get_status_policy) - 1,
+ },
};
static const struct genl_multicast_group ethtool_nl_mcgrps[] = {
extern const struct ethnl_request_ops ethnl_module_request_ops;
extern const struct ethnl_request_ops ethnl_pse_request_ops;
extern const struct ethnl_request_ops ethnl_rss_request_ops;
+extern const struct ethnl_request_ops ethnl_plca_cfg_request_ops;
+extern const struct ethnl_request_ops ethnl_plca_status_request_ops;
extern const struct nla_policy ethnl_header_policy[ETHTOOL_A_HEADER_FLAGS + 1];
extern const struct nla_policy ethnl_header_policy_stats[ETHTOOL_A_HEADER_FLAGS + 1];
extern const struct nla_policy ethnl_pse_get_policy[ETHTOOL_A_PSE_HEADER + 1];
extern const struct nla_policy ethnl_pse_set_policy[ETHTOOL_A_PSE_MAX + 1];
extern const struct nla_policy ethnl_rss_get_policy[ETHTOOL_A_RSS_CONTEXT + 1];
+extern const struct nla_policy ethnl_plca_get_cfg_policy[ETHTOOL_A_PLCA_HEADER + 1];
+extern const struct nla_policy ethnl_plca_set_cfg_policy[ETHTOOL_A_PLCA_MAX + 1];
+extern const struct nla_policy ethnl_plca_get_status_policy[ETHTOOL_A_PLCA_HEADER + 1];
int ethnl_set_linkinfo(struct sk_buff *skb, struct genl_info *info);
int ethnl_set_linkmodes(struct sk_buff *skb, struct genl_info *info);
int ethnl_set_fec(struct sk_buff *skb, struct genl_info *info);
int ethnl_set_module(struct sk_buff *skb, struct genl_info *info);
int ethnl_set_pse(struct sk_buff *skb, struct genl_info *info);
+int ethnl_set_plca_cfg(struct sk_buff *skb, struct genl_info *info);
extern const char stats_std_names[__ETHTOOL_STATS_CNT][ETH_GSTRING_LEN];
extern const char stats_eth_phy_names[__ETHTOOL_A_STATS_ETH_PHY_CNT][ETH_GSTRING_LEN];
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/phy.h>
+#include <linux/ethtool_netlink.h>
+
+#include "netlink.h"
+#include "common.h"
+
+struct plca_req_info {
+ struct ethnl_req_info base;
+};
+
+struct plca_reply_data {
+ struct ethnl_reply_data base;
+ struct phy_plca_cfg plca_cfg;
+ struct phy_plca_status plca_st;
+};
+
+// Helpers ------------------------------------------------------------------ //
+
+#define PLCA_REPDATA(__reply_base) \
+ container_of(__reply_base, struct plca_reply_data, base)
+
+static void plca_update_sint(int *dst, const struct nlattr *attr,
+ bool *mod)
+{
+ if (!attr)
+ return;
+
+ *dst = nla_get_u32(attr);
+ *mod = true;
+}
+
+// PLCA get configuration message ------------------------------------------- //
+
+const struct nla_policy ethnl_plca_get_cfg_policy[] = {
+ [ETHTOOL_A_PLCA_HEADER] =
+ NLA_POLICY_NESTED(ethnl_header_policy),
+};
+
+static int plca_get_cfg_prepare_data(const struct ethnl_req_info *req_base,
+ struct ethnl_reply_data *reply_base,
+ struct genl_info *info)
+{
+ struct plca_reply_data *data = PLCA_REPDATA(reply_base);
+ struct net_device *dev = reply_base->dev;
+ const struct ethtool_phy_ops *ops;
+ int ret;
+
+ // check that the PHY device is available and connected
+ if (!dev->phydev) {
+ ret = -EOPNOTSUPP;
+ goto out;
+ }
+
+ // note: rtnl_lock is held already by ethnl_default_doit
+ ops = ethtool_phy_ops;
+ if (!ops || !ops->get_plca_cfg) {
+ ret = -EOPNOTSUPP;
+ goto out;
+ }
+
+ ret = ethnl_ops_begin(dev);
+ if (!ret)
+ goto out;
+
+ memset(&data->plca_cfg, 0xff,
+ sizeof_field(struct plca_reply_data, plca_cfg));
+
+ ret = ops->get_plca_cfg(dev->phydev, &data->plca_cfg);
+ ethnl_ops_complete(dev);
+
+out:
+ return ret;
+}
+
+static int plca_get_cfg_reply_size(const struct ethnl_req_info *req_base,
+ const struct ethnl_reply_data *reply_base)
+{
+ return nla_total_size(sizeof(u16)) + /* _VERSION */
+ nla_total_size(sizeof(u8)) + /* _ENABLED */
+ nla_total_size(sizeof(u32)) + /* _NODE_CNT */
+ nla_total_size(sizeof(u32)) + /* _NODE_ID */
+ nla_total_size(sizeof(u32)) + /* _TO_TIMER */
+ nla_total_size(sizeof(u32)) + /* _BURST_COUNT */
+ nla_total_size(sizeof(u32)); /* _BURST_TIMER */
+}
+
+static int plca_get_cfg_fill_reply(struct sk_buff *skb,
+ const struct ethnl_req_info *req_base,
+ const struct ethnl_reply_data *reply_base)
+{
+ const struct plca_reply_data *data = PLCA_REPDATA(reply_base);
+ const struct phy_plca_cfg *plca = &data->plca_cfg;
+
+ if ((plca->version >= 0 &&
+ nla_put_u16(skb, ETHTOOL_A_PLCA_VERSION, plca->version)) ||
+ (plca->enabled >= 0 &&
+ nla_put_u8(skb, ETHTOOL_A_PLCA_ENABLED, !!plca->enabled)) ||
+ (plca->node_id >= 0 &&
+ nla_put_u32(skb, ETHTOOL_A_PLCA_NODE_ID, plca->node_id)) ||
+ (plca->node_cnt >= 0 &&
+ nla_put_u32(skb, ETHTOOL_A_PLCA_NODE_CNT, plca->node_cnt)) ||
+ (plca->to_tmr >= 0 &&
+ nla_put_u32(skb, ETHTOOL_A_PLCA_TO_TMR, plca->to_tmr)) ||
+ (plca->burst_cnt >= 0 &&
+ nla_put_u32(skb, ETHTOOL_A_PLCA_BURST_CNT, plca->burst_cnt)) ||
+ (plca->burst_tmr >= 0 &&
+ nla_put_u32(skb, ETHTOOL_A_PLCA_BURST_TMR, plca->burst_tmr)))
+ return -EMSGSIZE;
+
+ return 0;
+};
+
+const struct ethnl_request_ops ethnl_plca_cfg_request_ops = {
+ .request_cmd = ETHTOOL_MSG_PLCA_GET_CFG,
+ .reply_cmd = ETHTOOL_MSG_PLCA_GET_CFG_REPLY,
+ .hdr_attr = ETHTOOL_A_PLCA_HEADER,
+ .req_info_size = sizeof(struct plca_req_info),
+ .reply_data_size = sizeof(struct plca_reply_data),
+
+ .prepare_data = plca_get_cfg_prepare_data,
+ .reply_size = plca_get_cfg_reply_size,
+ .fill_reply = plca_get_cfg_fill_reply,
+};
+
+// PLCA set configuration message ------------------------------------------- //
+
+const struct nla_policy ethnl_plca_set_cfg_policy[] = {
+ [ETHTOOL_A_PLCA_HEADER] =
+ NLA_POLICY_NESTED(ethnl_header_policy),
+ [ETHTOOL_A_PLCA_ENABLED] = NLA_POLICY_MAX(NLA_U8, 1),
+ [ETHTOOL_A_PLCA_NODE_ID] = NLA_POLICY_MAX(NLA_U32, 255),
+ [ETHTOOL_A_PLCA_NODE_CNT] = NLA_POLICY_RANGE(NLA_U32, 1, 255),
+ [ETHTOOL_A_PLCA_TO_TMR] = NLA_POLICY_MAX(NLA_U32, 255),
+ [ETHTOOL_A_PLCA_BURST_CNT] = NLA_POLICY_MAX(NLA_U32, 255),
+ [ETHTOOL_A_PLCA_BURST_TMR] = NLA_POLICY_MAX(NLA_U32, 255),
+};
+
+int ethnl_set_plca_cfg(struct sk_buff *skb, struct genl_info *info)
+{
+ struct ethnl_req_info req_info = {};
+ struct nlattr **tb = info->attrs;
+ const struct ethtool_phy_ops *ops;
+ struct phy_plca_cfg plca_cfg;
+ struct net_device *dev;
+ bool mod = false;
+ int ret;
+
+ ret = ethnl_parse_header_dev_get(&req_info,
+ tb[ETHTOOL_A_PLCA_HEADER],
+ genl_info_net(info), info->extack,
+ true);
+ if (!ret)
+ return ret;
+
+ dev = req_info.dev;
+
+ rtnl_lock();
+
+ // check that the PHY device is available and connected
+ if (!dev->phydev) {
+ ret = -EOPNOTSUPP;
+ goto out_rtnl;
+ }
+
+ ops = ethtool_phy_ops;
+ if (!ops || !ops->set_plca_cfg) {
+ ret = -EOPNOTSUPP;
+ goto out_rtnl;
+ }
+
+ ret = ethnl_ops_begin(dev);
+ if (!ret)
+ goto out_rtnl;
+
+ memset(&plca_cfg, 0xff, sizeof(plca_cfg));
+ plca_update_sint(&plca_cfg.enabled, tb[ETHTOOL_A_PLCA_ENABLED], &mod);
+ plca_update_sint(&plca_cfg.node_id, tb[ETHTOOL_A_PLCA_NODE_ID], &mod);
+ plca_update_sint(&plca_cfg.node_cnt, tb[ETHTOOL_A_PLCA_NODE_CNT], &mod);
+ plca_update_sint(&plca_cfg.to_tmr, tb[ETHTOOL_A_PLCA_TO_TMR], &mod);
+ plca_update_sint(&plca_cfg.burst_cnt, tb[ETHTOOL_A_PLCA_BURST_CNT],
+ &mod);
+ plca_update_sint(&plca_cfg.burst_tmr, tb[ETHTOOL_A_PLCA_BURST_TMR],
+ &mod);
+
+ ret = 0;
+ if (!mod)
+ goto out_ops;
+
+ ret = ops->set_plca_cfg(dev->phydev, &plca_cfg, info->extack);
+ if (!ret)
+ goto out_ops;
+
+ ethtool_notify(dev, ETHTOOL_MSG_PLCA_NTF, NULL);
+
+out_ops:
+ ethnl_ops_complete(dev);
+out_rtnl:
+ rtnl_unlock();
+ ethnl_parse_header_dev_put(&req_info);
+
+ return ret;
+}
+
+// PLCA get status message -------------------------------------------------- //
+
+const struct nla_policy ethnl_plca_get_status_policy[] = {
+ [ETHTOOL_A_PLCA_HEADER] =
+ NLA_POLICY_NESTED(ethnl_header_policy),
+};
+
+static int plca_get_status_prepare_data(const struct ethnl_req_info *req_base,
+ struct ethnl_reply_data *reply_base,
+ struct genl_info *info)
+{
+ struct plca_reply_data *data = PLCA_REPDATA(reply_base);
+ struct net_device *dev = reply_base->dev;
+ const struct ethtool_phy_ops *ops;
+ int ret;
+
+ // check that the PHY device is available and connected
+ if (!dev->phydev) {
+ ret = -EOPNOTSUPP;
+ goto out;
+ }
+
+ // note: rtnl_lock is held already by ethnl_default_doit
+ ops = ethtool_phy_ops;
+ if (!ops || !ops->get_plca_status) {
+ ret = -EOPNOTSUPP;
+ goto out;
+ }
+
+ ret = ethnl_ops_begin(dev);
+ if (!ret)
+ goto out;
+
+ memset(&data->plca_st, 0xff,
+ sizeof_field(struct plca_reply_data, plca_st));
+
+ ret = ops->get_plca_status(dev->phydev, &data->plca_st);
+ ethnl_ops_complete(dev);
+out:
+ return ret;
+}
+
+static int plca_get_status_reply_size(const struct ethnl_req_info *req_base,
+ const struct ethnl_reply_data *reply_base)
+{
+ return nla_total_size(sizeof(u8)); /* _STATUS */
+}
+
+static int plca_get_status_fill_reply(struct sk_buff *skb,
+ const struct ethnl_req_info *req_base,
+ const struct ethnl_reply_data *reply_base)
+{
+ const struct plca_reply_data *data = PLCA_REPDATA(reply_base);
+ const u8 status = data->plca_st.pst;
+
+ if (nla_put_u8(skb, ETHTOOL_A_PLCA_STATUS, !!status))
+ return -EMSGSIZE;
+
+ return 0;
+};
+
+const struct ethnl_request_ops ethnl_plca_status_request_ops = {
+ .request_cmd = ETHTOOL_MSG_PLCA_GET_STATUS,
+ .reply_cmd = ETHTOOL_MSG_PLCA_GET_STATUS_REPLY,
+ .hdr_attr = ETHTOOL_A_PLCA_HEADER,
+ .req_info_size = sizeof(struct plca_req_info),
+ .reply_data_size = sizeof(struct plca_reply_data),
+
+ .prepare_data = plca_get_status_prepare_data,
+ .reply_size = plca_get_status_reply_size,
+ .fill_reply = plca_get_status_fill_reply,
+};
projects / platform / kernel / linux-rpi.git / commitdiff