at91/picotux200: remove commenting usb device and dataflash support

as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index ac1a3b5..55dad3a 100644 (file)
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -74,11 +74,6 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = {
        .ports          = 1,
 };
 
-// static struct at91_udc_data __initdata picotux200_udc_data = {
-//     .vbus_pin       = AT91_PIN_PD4,
-//     .pullup_pin     = AT91_PIN_PD5,
-// };
-
 static struct at91_mmc_data __initdata picotux200_mmc_data = {
        .det_pin        = AT91_PIN_PB27,
        .slot_b         = 0,
@@ -86,21 +81,6 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
        .wp_pin         = AT91_PIN_PA17,
 };
 
-// static struct spi_board_info picotux200_spi_devices[] = {
-//     {       /* DataFlash chip */
-//             .modalias       = "mtd_dataflash",
-//             .chip_select    = 0,
-//             .max_speed_hz   = 15 * 1000 * 1000,
-//     },
-// #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-//     {       /* DataFlash card */
-//             .modalias       = "mtd_dataflash",
-//             .chip_select    = 3,
-//             .max_speed_hz   = 15 * 1000 * 1000,
-//     },
-// #endif
-// };
-
 #define PICOTUX200_FLASH_BASE  AT91_CHIPSELECT_0
 #define PICOTUX200_FLASH_SIZE  SZ_4M
 
@@ -132,21 +112,11 @@ static void __init picotux200_board_init(void)
        at91_add_device_eth(&picotux200_eth_data);
        /* USB Host */
        at91_add_device_usbh(&picotux200_usbh_data);
-       /* USB Device */
-       // at91_add_device_udc(&picotux200_udc_data);
-       // at91_set_multi_drive(picotux200_udc_data.pullup_pin, 1);     /* pullup_pin is connected to reset */
        /* I2C */
        at91_add_device_i2c(NULL, 0);
-       /* SPI */
-       // at91_add_device_spi(picotux200_spi_devices, ARRAY_SIZE(picotux200_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-       /* DataFlash card */
-       at91_set_gpio_output(AT91_PIN_PB22, 0);
-#else
        /* MMC */
        at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
        at91_add_device_mmc(0, &picotux200_mmc_data);
-#endif
        /* NOR Flash */
        platform_device_register(&picotux200_flash);
 }