+commit 2d78074d2e806edc380c1464eb9e5df335ece65e
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Jun 22 17:32:28 2007 +0200
+
+ ppc7xx: Update CPCI750 board
+
+ This small CPCI750 update extends the board specific command
+ "show_config" to display the Marvell strapping registers and
+ extends the PCI IDE controller.
+
+ Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 30b52df9e906bf0e465916c2c6bb5192b438e0b8
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Wed Aug 15 11:55:35 2007 -0500
+
+ 86xx: Fix lingering CFG_CMD_* references in sbc8641d.h
+
+ Remove a leftover in net/tftp.c while we're at it.
+
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 4ce917742b1e48faa9bf9a9757545e56fb4cfe44
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Wed Aug 15 12:20:40 2007 -0500
+
+ Move the MPC8641HPCN board under board/freescale.
+
+ Minor path corrections needed to ensure buildability.
+
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 8662577fe36fdb6a44b55b998d9daac6392a736a
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Wed Aug 15 11:46:22 2007 -0500
+
+ 86xx: Fix lingering CFG_CMD_* references in sbc8641d.h
+
+ Remove a leftover in net/tftp.c while we're at it.
+
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 210f463c71917b7a4495c2103c228b9c179ae64d
+Author: Jerry Van Baren <gvb.uboot@gmail.com>
+Date: Wed Aug 15 11:13:15 2007 -0400
+
+ Fix where the #ifdef CFG_BOOTMAPSZ is placed.
+
+ Commit 073e1b509980cefe6f53c2d7fbbcd135df1e3924 "Fix initrd/dtb
+ interaction" put the new code outside of the #if defined(CONFIG_OF_LIBFDT)
+ when it should have gone inside of the conditional. As a result, it
+ broke non-LIBFDT board builds.
+
+ Also added a missing "not." to the comment.
+
+ Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
+
+commit 594e79838ce5078a90d0c27abb2b2d61d5f8e8a7
+Author: Ed Swarthout <Ed.Swarthout@freescale.com>
+Date: Tue Aug 14 14:06:45 2007 -0500
+
+ Fix malloc size error in ahci_init_one.
+
+ Typically this causes scsi init to corrupt the
+ devlist and break the coninfo command.
+ Fix a compiler size warning.
+
+ Signed-off-by: Jason Jin <jason.jin@freescale.com>
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
+commit b361acd64fd2525c081b9b288b0804efe209c0e9
+Author: ksi@koi8.net <ksi@koi8.net>
+Date: Tue Aug 14 10:02:16 2007 -0700
+
+ TI DaVinci - fix unsupported %hhx format
+
+ Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
+
+commit f01dbb5424a81453c81190dd30e945891466f621
+Author: Wolfgang Denk <wd@denx.de>
+Date: Tue Aug 14 18:42:36 2007 +0200
+
+ Coding style cleanup. Update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
commit 073e1b509980cefe6f53c2d7fbbcd135df1e3924
Author: Andy Fleming <afleming@freescale.com>
Date: Tue Aug 14 10:32:59 2007 -0500
Supply spi interface in at45.c
+commit 4ce846ec59f36b85d6644a769690ad3feb667575
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Aug 14 15:12:01 2007 +0200
+
+ POST: Fix merge problem
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 429d9571f60631ae8a2fe12b11be4c75b0c2b37c
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Aug 14 15:03:17 2007 +0200
+
+ Coding style cleanup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 779e975117a75e91fcebe226a63104dbfb924ab1
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Aug 14 14:44:41 2007 +0200
+
+ ppc4xx: Add initial Zeus (PPC405EP) board support
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit c5a172a5fd636c12467429e3f7910e53773979c6
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Aug 14 14:41:55 2007 +0200
+
+ POST: Add option for external ethernet loopback test
+
+ When CFG_POST_ETHER_EXT_LOOPBACK is defined, the ethernet POST
+ is not done using an internal loopback connection, but by assuming
+ that an external loopback connector is plugged into the board.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit eb2b4010ae426245172988804ee8d9193fb41038
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Aug 14 14:39:44 2007 +0200
+
+ POST: Add ppc405 support to cache and UART POST
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 0c42f36f15074bd9808a7dbd7ef611fad9bf537c
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Aug 14 10:46:32 2007 +0100
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
+commit 273db7e1bdd1937e32f1d4507321bb721ebd3118
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Aug 13 09:05:33 2007 +0200
+
+ ppc4xx: Fix problem in PLL clock calculation
+
+ This patch was originall provided by David Mitchell <dmitchell@amcc.com>
+ and fixes a bug in the PLL clock calculation.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 9986bc3e40e899bea372a99a2bca4071bdf2e24b
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 12 21:34:50 2007 +0200
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
+commit 35d22f957a85a22bb3cd1ad084fa5404620d1c42
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Aug 10 10:42:25 2007 +0200
+
+ Coding style cleanup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 3a6d56c20989fe27360afe743bd2a7ad4d76e48f
Author: Dirk Behme <dirk.behme@googlemail.com>
Date: Thu Aug 2 17:42:08 2007 +0200
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
+commit 157cda4d0c3d592ccbb19bbfc07d9251894f0894
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Jul 27 11:31:22 2007 +0200
+
+ Add PPC4xx-HCU4 and HCU5 boards: HCU5 files
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit 6e5de26c6e7580faf16e87745cd488b92b492d0c
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Jul 27 11:30:33 2007 +0200
+
+ Add PPC4xx-HCU4 and HCU5 boards: HCU4 files
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit e8397fc78c9394d71de233a4d810fbc9047e4c76
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Jul 27 11:38:26 2007 +0200
+
+ Add PPC4xx-HCU4 and HCU5 boards: common files
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit ac982ea5a4f2f993efcf52dca122f5a59df047d8
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Jul 27 11:28:44 2007 +0200
+
+ Add PPC4xx-HCU4 and HCU5 boards: make related
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit 137fdd9f474ecb853efdace5200576308c67f18d
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Jul 27 11:28:03 2007 +0200
+
+ Add PPC4xx-HCU4 and HCU5 boards: HCU5 config
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit 714bc55b35b6f6a65cc8740a3842a543e88cdef2
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Jul 27 11:27:15 2007 +0200
+
+ Add PPC4xx-HCU4 and HCU5 boards: HCU4 config
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit 1894dd381124bdbfbdae7cf3a6ca52a8eb1f4421
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Jul 27 11:25:31 2007 +0200
+
+ Add PPC4xx-HCU4 and HCU5 boards: READMEs
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit 641cca9569ce351ddb287fd3343d8b1dcb591db4
+Author: Niklaus Giger <niklausgiger@gmx.ch>
+Date: Fri Jul 27 11:37:40 2007 +0200
+
+ Add PPC4xx-HCU4 and HCU5 boards: Infrastructure
+
+ This series of patches adds support for 2 boards from Netstal Maschinen.
+
+ The HCU4 has a PPC405Gpr and
+ the HCU5 has a PPC440EPX.
+
+ The HCU4 has a somehow complicated flash setup, as the booteprom is
+ only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
+ elegant solution.
+
+ The HCU5 has only a booteprom as the whole code will be downloaded from a
+ different board which has HD, CD-ROM, etc and where all code is stored.
+
+ This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
+ Thanks them a lot.
+
+ Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
+
+commit 3e4c90c6233618fc1806e63fde68df5f3d6a0171
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Aug 10 08:42:55 2007 +0200
+
+ ppc4xx: Update lwmon5 POST configuration
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 29cb25da56afe18cf5e7072a92a9d98ea8af1fd4
+Author: Yuri Tikhonov <yur@emcraft.com>
+Date: Fri Aug 10 08:25:22 2007 +0200
+
+ POST: Add ppc4xx UART POST support without external uart clock (lwmon5)
+
+ The patch adds support for UART POST on ppc44x-based boards with no
+ external serial clocks installed.
+
+ Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
+ Acked-by: Stefan Roese <sr@denx.de>
+
commit 99c2fdab91bc633e46fb41dbaa629f87ccf6e00f
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Mon Aug 6 18:18:34 2007 -0500
Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit 537223afa61f64480df31ce440a9cb386df4a814
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Aug 6 21:10:17 2007 +0200
+
+ ppc4xx: Update AMCC Bamboo README doc/README.bamboo
+
+ As suggested by Eugene O'Brien <Eugene.O'Brien@advantechamt.com>,
+ here an updated Bamboo README.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 9c7e4b06214db61bb21f1bcbe57c97519669baae
Author: Wolfgang Denk <wd@denx.de>
Date: Mon Aug 6 02:17:36 2007 +0200
Minor cleanup of <board>_nand build rules.
+commit 9ca8d79de096c65b9b9c867259b3ff4685f775ef
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Aug 2 08:33:56 2007 +0200
+
+ ppc4xx: Code cleanup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit c92409812206ac67a7fa7aae298539a9c3804a46
+Author: Grzegorz Bernacki <gjb@semihalf.com>
+Date: Tue Jul 31 18:51:48 2007 +0200
+
+ [ppc440SPe] Graceful recovery from machine check during PCIe configuration
+
+ During config transactions on the PCIe bus an attempt to scan for a
+ non-existent device can lead to a machine check exception with certain
+ peripheral devices. In order to avoid crashing in such scenarios the
+ instrumented versions of the config cycle read routines are introduced, so
+ the exceptions fixups framework can gracefully recover.
+
+ Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
+ Acked-by: Rafal Jaworowski <raj@semihalf.com>
+
+commit dec99558b9ea75a37940d07f41a3565a50b54ad1
+Author: Rafal Jaworowski <raj@semihalf.com>
+Date: Tue Jul 31 18:19:54 2007 +0200
+
+ [ppc4xx] Separate settings for PCIe bus numbering on 440SPe rev.A
+
+ This brings back separate settings for PCIe bus numbers depending on chip
+ revision, which got eliminated in 2b393b0f0af8402ef43b25c1968bfd29714ddffa
+ commit. 440SPe rev. A does NOT work properly with the same settings as for
+ the rev. B (no devices are seen on the bus during enumeration).
+
+ Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
+
commit cdd917a43da6fa7fc8f54a3cc9f420ce5ecf3197
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Aug 2 00:48:45 2007 +0200
Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit d2f68006627eda6cb6c7f364bddf621dbfd2fc68
+Author: Eugene OBrien <eugene.obrien@advantechamt.com>
+Date: Tue Jul 31 10:24:56 2007 +0200
+
+ ppc4xx: Update AMCC Bamboo 440EP support
+
+ Changed storage type of cfg_simulate_spd_eeprom to const
+ Changed storage type of gpio_tab to stack storage
+ (Cannot access global data declarations in .bss until afer code relocation)
+
+ Improved SDRAM tests to catch problems where data is not uniquely addressable
+ (e.g. incorrectly programmed SDRAM row or columns)
+
+ Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules
+ Fixed AM29LV320DT (OpCode Flash) sector map
+
+ Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit ea9f6bce383cc9fbcdee28b5836109b1a6dba574
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Jul 31 08:37:01 2007 +0200
+
+ ppc4xx: Update 440EPx lwmon5 board support
+
+ - Clear ECC status regs after ECC POST test
+ - Set dcbz for ECC generation with caches enabled as default
+ - Code cleanup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 27a528fb41433c4c1e2b5d6bd3fd8d78606fc724
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Jul 30 11:04:57 2007 +0200
+
+ ppc4xx: Only print ECC related info when the error bis are set
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit e36220a4baf1f188ba60f17e9d0f043069b1362a
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Fri Jul 27 16:44:31 2007 +0200
+
+ new FPGA image for PLU405 board
+
+ new FPGA image for PLU405 board with improved CompactFlash timing
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+
commit 8993e54b6f397973794f3d6f47d3b3c0c98dd4f6
Author: Rafal Jaworowski <raj@semihalf.com>
Date: Fri Jul 27 14:43:59 2007 +0200
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
+commit d4024bb72dd81695ec099b2199eda0d27c623e62
+Author: John Otken <john@softadvances.com>
+Date: Thu Jul 26 17:49:11 2007 +0200
+
+ ppc4xx: Add support for AMCC 405EP Taihu board
+
+ Signed-off-by: John Otken <john@softadvances.com>
+
+commit b66091de6c7390620312c2501db23d8391e7cabb
+Author: Anatolij Gustschin <agust@denx.de>
+Date: Thu Jul 26 15:08:01 2007 +0200
+
+ ppc4xx: lwmon5: Update Lime initialization
+
+ Change Lime SDRAM initialization to now support 100MHz and
+ 133MHz (if enabled). Also the framebuffer is initialized to
+ display a blue rectangle with a white border.
+
+ Signed-off-by: Anatolij Gustschin <agust@denx.de>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 9f24a808f17fc0f37b7fb4805f734741335caecc
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Jul 24 09:52:52 2007 +0200
+
+ ppc4xx: lwmon5: Support for 128 MByte NOR FLASH added
+
+ The used Intel NOR FLASH chips have internally two dies, and are now
+ treated as two seperate chips.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit aedf5bde179ecfbd0a96130d18996a96518b785f
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Jul 24 07:20:09 2007 +0200
+
+ ppc4xx: Fix lwmon5 interrupt controller setup (polarity, trigger...)
+
+ As suggested by Hakan Eryigit, here an updated setup for the lwmon5
+ interrupt controller.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit a71d96eac8130b53a91f93cd10c70fca0db18d52
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Jul 20 15:03:44 2007 +0200
+
+ ppc4xx: Fix bug with default GPIO output value
+
+ As spotted by Matthias Fuchs, the default output values for all GPIO1
+ outputs were not setup correctly. This patch fixes this issue.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 531e3e8b831f357056448fa573137d5fb37000fd
+Author: Pavel Kolesnikov <concord@emcraft.com>
+Date: Fri Jul 20 15:03:03 2007 +0200
+
+ POST: Add ECC POST for the lwmon5 board
+
+ This patch adds ECC Post test for the Lwmon5 board based
+ on PPC440EPx to U-Boot.
+
+ Signed-off-by: Pavel Kolesnikov <concord@emcraft.com>
+ Acked-by: Yuri Tikhonov <yur@emcraft.com>
+ Acked-by: Stefan Roese <sr@denx.de>
+
commit cc3023b9f95d7ac959a764471a65001062aecf41
Author: Rafal Jaworowski <raj@semihalf.com>
Date: Thu Jul 19 17:12:28 2007 +0200
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
+commit 8848ec858f74ed6dab06fb6d5ddc933e0a1328bf
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Jul 16 10:02:12 2007 +0200
+
+ ppc4xx: Code cleanup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 2a49fc17d09020e7ebd9536694d99d20e419fcb8
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Jul 16 10:01:38 2007 +0200
+
+ ppc4xx: AMCC Luan uses the new boardspecific DDR2 controller setup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit df3f17422aeb03fb81a7ac8c78d2b05d05aa4cf9
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Jul 16 10:00:43 2007 +0200
+
+ ppc4xx: Support for Yucca board with 440SPe Rev A added to 44x_spd_ddr2.c
+
+ The new boardspecific DDR2 controller configuration is used for the Yucca
+ board. Now the Yucca board with 440SPe Rev. A chips is also supported.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 6ed14addf97c8cd8f531e9ae7b2d3e222fffd53e
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Jul 16 09:57:00 2007 +0200
+
+ ppc4xx: Add new weak functions to support boardspecific DDR2 configuration
+
+ The new "weak" functions ddr_wrdtr() and ddr_clktr() are added to better
+ support non default, boardspecific DDR(2) controller configuration.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 5743a9207a370b90f09b20ebd61167c806b937f3
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Jul 16 08:53:51 2007 +0200
+
+ ppc4xx: Add remove_tlb() function to remove a mem area from TLB setup
+
+ The new function remove_tlb() can be used to remove the TLB's used to
+ map a specific memory region. This is especially useful for the DDR(2)
+ setup routines which configure the SDRAM area temporarily as a cached
+ area (for speedup on auto-calibration and ECC generation) and later
+ need this area uncached for normal usage.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 3a6cab844cf74f76639d795e0be8717e02c86af7
Author: Wolfgang Denk <wd@denx.de>
Date: Sat Jul 14 22:51:02 2007 +0200
Signed-off-by: Heiko Schocher <hs@denx.de>
+commit a2e1c7098cf9574386b0c96841dfc8ea5cc93578
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Jul 12 16:32:08 2007 +0200
+
+ ppc4xx: Change receive buffer handling in the 4xx emac driver
+
+ This change fixes a bug in the receive buffer handling, that
+ could lead to problems upon high network traffic (broadcasts...).
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 239f05ee4dd4cfe0b50f251b533dcebe9e67c360
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Jul 12 01:45:34 2007 +0200
Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit c8603cfbd4573379a6076c9c208545ba2bbf019a
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Jul 9 11:00:24 2007 +0200
+
+ Small coding style cleanup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 0f92c7e7c9a62755b1457d3c46f93c8c1f6c19fc
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Mon Jul 9 10:10:08 2007 +0200
+
+ Migrate esd 405EP boards to new NAND subsystem
+
+ Remove unused CFG_NAND_LEGACY define
+
+ These boards to not have NAND.
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+
+commit bd84ee4c2020c3a6861f4bb2e7ea0fb49f82e803
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Mon Jul 9 10:10:06 2007 +0200
+
+ Migrate esd 405EP boards to new NAND subsystem
+
+ Migrate esd 405EP boards to new NAND subsystem
+
+ -cleanup
+ -use correct io accessors (in/out_be32())
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+
+commit e09f7ab5749c345f924da272bea0521a73af5b11
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Mon Jul 9 10:10:04 2007 +0200
+
+ Migrate esd 405EP boards to new NAND subsystem
+
+ This patch prepares the migration from the legacy NAND driver
+ to U-Boot's new NAND subsystem for esd boards.
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+
commit c3517f919d0f61650cf3027fd4faf0f631142f6c
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 18:10:08 2007 -0500
Signed-off-by: Jon Loeliger <jdl@freescale.com>
+commit 10e038932f22ee80ebd53de312531e70e6590a2f
+Author: Thomas Knobloch <knobloch@siemens.com>
+Date: Fri Jul 6 14:58:39 2007 +0200
+
+ [NAND] Bad block skipping for command nboot
+
+ The old implementation of command nboot does not support reading the image from
+ NAND flash with skipping of bad blocks. The patch implements a new version of
+ the nboot command: by calling nboot.jffs2 from the u-boot command line the
+ command will load the image from NAND flash with respect to bad blocks (by using
+ nand_read_opts()). This is similar to e.g. the NAND read command: "nand
+ read.jffs2 ...".
+
+ Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 334043f601a90ac53e5ecc846fbb73a1ef38cb1f
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Jul 6 12:26:51 2007 +0200
+
+ ppc4xx: Update lwmon5 default environment
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 5d187430a055d62f17ca84d75e7245439d1f7e75
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Jul 6 11:48:24 2007 +0200
+
+ ppc4xx: Update lwmon5 board
+
+ Add unlock=yes environment variable to default variables to unlock
+ the CFI flash by default.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 6b0a174a1e6f55e1f5a1fbb223cdad7645a4646e
Author: Stefan Roese <sr@denx.de>
Date: Fri Jul 6 09:45:47 2007 +0200
- adapt to the more generic EXCEPTION_PROLOG and CRIT_EXCEPTION macros
- minor 4xx cleanup
+commit d677b32855f577ae2690dcd64a172cdd706e0ffc
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Fri Jun 22 10:34:12 2007 +0200
+
+ [patch] add nand_init() prototype to nand.h
+
+ since nand_init() is expected to be called by other parts of u-boot, there
+ should be a prototype for it in nand.h
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 83b4cfa3d629dff0264366263c5e94d9a50ad80b
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Jun 20 18:14:24 2007 +0200
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
+commit 7ebb4479b07ff294eb4d76e420753a0349f7c93b
+Author: Ulf Samuelsson <ulf@atmel.com>
+Date: Thu May 24 12:12:47 2007 +0200
+
+ [PATCH][NAND] Define the Vendor Id for Micron NAND Flash
+
+ Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
+ Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit d756894722c888d09a9fa1df8323753772d3dcce
Author: Stefan Roese <sr@denx.de>
Date: Thu May 24 09:49:00 2007 +0200
VOH405 PPC405EP
VOM405 PPC405EP
WUH405 PPC405EP
- CMS700 PPC405EP
+ CMS700 PPC405EP
Niklaus Giger <niklaus.giger@netstal.com>
- HCU4 PPC405GPr
- HCU5 PPC440EPx
+ HCU4 PPC405GPr
+ HCU5 PPC440EPx
Frank Gottschling <fgottschling@eltec.de>
ZUMA \
"
+LIST_TSEC=" \
+ ${LIST_85xx} \
+ ${LIST_86xx} \
+ ${LIST_83xx} \
+"
+
LIST_7xx=" \
BAB7xx \
CPCI750 \
mips|mips_el| \
nios|nios2| \
ppc|5xx|5xxx|512x|8xx|8220|824x|8260|83xx|85xx|86xx|4xx|7xx|74xx| \
- x86|I486)
+ x86|I486|TSEC)
for target in `eval echo '$LIST_'${arg}`
do
build_target ${target}
#########################################################################
MPC8641HPCN_config: unconfig
- @$(MKCONFIG) $(@:_config=) ppc mpc86xx mpc8641hpcn
+ @$(MKCONFIG) $(@:_config=) ppc mpc86xx mpc8641hpcn freescale
sbc8641d_config: unconfig
@./mkconfig $(@:_config=) ppc mpc86xx sbc8641d
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o flash.o ../common/misc.o
+COBJS = $(BOARD).o flash.o \
+ ../common/misc.o \
+ ../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
#include <common.h>
#include <asm/processor.h>
+#include <asm/io.h>
#include <command.h>
#include <malloc.h>
#endif
extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+extern void lxt971_no_sleep(void);
/* fpga configuration data - gzip compressed and generated by bin2c */
const unsigned char fpgadata[] =
/*
* Reset external DUARTs
*/
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_DUART_RST);
udelay(10); /* wait 10us */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_DUART_RST);
udelay(1000); /* wait 1ms */
/*
- * Set NAND-FLASH GPIO signals to default
- */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
- /*
* Enable interrupts in exar duart mcr[3]
*/
*duart0_mcr = 0x08;
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
-#if 0
- printf("\nmb0cf=%x\n", val); /* test-only */
- printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
/* ------------------------------------------------------------------------- */
-int testdram (void)
+void reset_phy(void)
{
- /* TODO: XXX XXX XXX */
- printf ("test: 16 MB - ok\n");
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
- nand_probe(CFG_NAND_BASE);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-}
+#ifdef CONFIG_LXT971_NO_SLEEP
+ /*
+ * Disable sleep mode in LXT971
+ */
+ lxt971_no_sleep();
#endif
+}
../common/xilinx_jtag/micro.o \
../common/xilinx_jtag/ports.o
-COBJS = $(BOARD).o flash.o ../common/misc.o $(CPLD)
+COBJS = $(BOARD).o flash.o \
+ ../common/misc.o \
+ $(CPLD) \
+ ../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
/*
- * (C) Copyright 2005
+ * (C) Copyright 2005-2007
* Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
#include <common.h>
#include <asm/processor.h>
+#include <asm/io.h>
#include <command.h>
#include <malloc.h>
/*
* Reset CPLD via GPIO12 (CS3) pin
*/
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_PLD_RESET);
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_PLD_RESET);
udelay(1000); /* wait 1ms */
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_PLD_RESET);
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_PLD_RESET);
udelay(1000); /* wait 1ms */
return 0;
/*
* Setup and enable EEPROM write protection
*/
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
-
- /*
- * Set NAND-FLASH GPIO signals to default
- */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_EEPROM_WP);
return (0);
}
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
-#if 0
- printf("\nmb0cf=%x\n", val); /* test-only */
- printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
switch (state) {
case 1:
/* Enable write access, clear bit GPIO_SINT2. */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_EEPROM_WP);
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_EEPROM_WP);
state = 0;
break;
case 0:
/* Disable write access, set bit GPIO_SINT2. */
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_EEPROM_WP);
state = 0;
break;
default:
/* Read current status back. */
- state = (0 == (in32(GPIO0_OR) & CFG_EEPROM_WP));
+ state = (0 == (in_be32((void *)GPIO0_OR) & CFG_EEPROM_WP));
break;
}
}
/* ------------------------------------------------------------------------- */
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
- nand_probe(CFG_NAND_BASE);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-}
-#endif
-
void reset_phy(void)
{
#ifdef CONFIG_LXT971_NO_SLEEP
#include <command.h>
#include <image.h>
#include <asm/byteorder.h>
+#if defined(CFG_NAND_LEGACY)
#include <linux/mtd/nand_legacy.h>
+#endif
#include <fat.h>
#include <part.h>
rc = nand_legacy_rw(nand_dev_desc, NANDRW_WRITE | NANDRW_JFFS2,
start, nbytes, (size_t *)&total, (uchar *)addr);
debug ("nand_legacy_rw: ret=%x total=%d nbytes=%d\n", rc, total, nbytes);
+#else
+ rc = -1;
#endif
}
if (rc != 0) {
--- /dev/null
+/*
+ * (C) Copyright 2007
+ * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#if defined(CONFIG_CMD_NAND)
+#include <asm/io.h>
+#include <nand.h>
+
+/*
+ * hardware specific access to control-lines
+ */
+static void esd405ep_nand_hwcontrol(struct mtd_info *mtdinfo, int cmd)
+{
+ switch(cmd) {
+ case NAND_CTL_SETCLE:
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_CLE);
+ break;
+ case NAND_CTL_CLRCLE:
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_CLE);
+ break;
+ case NAND_CTL_SETALE:
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_ALE);
+ break;
+ case NAND_CTL_CLRALE:
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_ALE);
+ break;
+ case NAND_CTL_SETNCE:
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_CE);
+ break;
+ case NAND_CTL_CLRNCE:
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_CE);
+ break;
+ }
+}
+
+
+/*
+ * read device ready pin
+ */
+static int esd405ep_nand_device_ready(struct mtd_info *mtdinfo)
+{
+ if (in_be32((void *)GPIO0_IR) & CFG_NAND_RDY)
+ return 1;
+ return 0;
+}
+
+
+int board_nand_init(struct nand_chip *nand)
+{
+ /*
+ * Set NAND-FLASH GPIO signals to defaults
+ */
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_CE);
+
+ /*
+ * Initialize nand_chip structure
+ */
+ nand->hwcontrol = esd405ep_nand_hwcontrol;
+ nand->dev_ready = esd405ep_nand_device_ready;
+ nand->eccmode = NAND_ECC_SOFT;
+ nand->chip_delay = NAND_BIG_DELAY_US;
+ nand->options = NAND_SAMSUNG_LP_OPTIONS;
+ return 0;
+}
+#endif
#define DP(x)
#endif
+static char show_config_tab[][15] = {{"PCI0DLL_2 "}, /* 31 */
+ {"PCI0DLL_1 "}, /* 30 */
+ {"PCI0DLL_0 "}, /* 29 */
+ {"PCI1DLL_2 "}, /* 28 */
+ {"PCI1DLL_1 "}, /* 27 */
+ {"PCI1DLL_0 "}, /* 26 */
+ {"BbEP2En "}, /* 25 */
+ {"SDRAMRdDataDel"}, /* 24 */
+ {"SDRAMRdDel "}, /* 23 */
+ {"SDRAMSync "}, /* 22 */
+ {"SDRAMPipeSel_1"}, /* 21 */
+ {"SDRAMPipeSel_0"}, /* 20 */
+ {"SDRAMAddDel "}, /* 19 */
+ {"SDRAMClkSel "}, /* 18 */
+ {"Reserved(1!) "}, /* 17 */
+ {"PCIRty "}, /* 16 */
+ {"BootCSWidth_1 "}, /* 15 */
+ {"BootCSWidth_0 "}, /* 14 */
+ {"PCI1PadsCal "}, /* 13 */
+ {"PCI0PadsCal "}, /* 12 */
+ {"MultiMVId_1 "}, /* 11 */
+ {"MultiMVId_0 "}, /* 10 */
+ {"MultiGTEn "}, /* 09 */
+ {"Int60xArb "}, /* 08 */
+ {"CPUBusConfig_1"}, /* 07 */
+ {"CPUBusConfig_0"}, /* 06 */
+ {"DefIntSpc "}, /* 05 */
+ {0 }, /* 04 */
+ {"SROMAdd_1 "}, /* 03 */
+ {"SROMAdd_0 "}, /* 02 */
+ {"DRAMPadCal "}, /* 01 */
+ {"SInitEn "}, /* 00 */
+ {0 }, /* 31 */
+ {0 }, /* 30 */
+ {0 }, /* 29 */
+ {0 }, /* 28 */
+ {0 }, /* 27 */
+ {0 }, /* 26 */
+ {0 }, /* 25 */
+ {0 }, /* 24 */
+ {0 }, /* 23 */
+ {0 }, /* 22 */
+ {"JTAGCalBy "}, /* 21 */
+ {"GB2Sel "}, /* 20 */
+ {"GB1Sel "}, /* 19 */
+ {"DRAMPLL_MDiv_5"}, /* 18 */
+ {"DRAMPLL_MDiv_4"}, /* 17 */
+ {"DRAMPLL_MDiv_3"}, /* 16 */
+ {"DRAMPLL_MDiv_2"}, /* 15 */
+ {"DRAMPLL_MDiv_1"}, /* 14 */
+ {"DRAMPLL_MDiv_0"}, /* 13 */
+ {"GB0Sel "}, /* 12 */
+ {"DRAMPLLPU "}, /* 11 */
+ {"DRAMPLL_HIKVCO"}, /* 10 */
+ {"DRAMPLLNP "}, /* 09 */
+ {"DRAMPLL_NDiv_7"}, /* 08 */
+ {"DRAMPLL_NDiv_6"}, /* 07 */
+ {"CPUPadCal "}, /* 06 */
+ {"DRAMPLL_NDiv_5"}, /* 05 */
+ {"DRAMPLL_NDiv_4"}, /* 04 */
+ {"DRAMPLL_NDiv_3"}, /* 03 */
+ {"DRAMPLL_NDiv_2"}, /* 02 */
+ {"DRAMPLL_NDiv_1"}, /* 01 */
+ {"DRAMPLL_NDiv_0"}}; /* 00 */
+
extern void flush_data_cache (void);
extern void invalidate_l1_instruction_cache (void);
extern flash_info_t flash_info[];
dcache_disable ();
}
-
-int do_show_cfg(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+int do_show_config(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
unsigned int reset_sample_low;
unsigned int reset_sample_high;
+ unsigned int l, l1, l2;
GT_REG_READ(0x3c4, &reset_sample_low);
GT_REG_READ(0x3d4, &reset_sample_high);
printf("Reset configuration 0x%08x 0x%08x\n", reset_sample_low, reset_sample_high);
+ l2 = 0;
+ for (l=0; l<63; l++) {
+ if (show_config_tab[l][0] != 0) {
+ printf("%14s:%1x ", show_config_tab[l],
+ ((reset_sample_low >> (31 - (l & 0x1f)))) & 0x01);
+ l2++;
+ if ((l2 % 4) == 0)
+ printf("\n");
+ } else {
+ l1++;
+ }
+ if (l == 32)
+ reset_sample_low = reset_sample_high;
+ }
+ printf("\n");
+
return(0);
}
U_BOOT_CMD(
- show_cfg, 1, 1, do_show_cfg,
- "show_cfg- Show Marvell strapping register\n",
+ show_config, 1, 1, do_show_config,
+ "show_config - Show Marvell strapping register\n",
"Show Marvell strapping register (ResetSampleLow ResetSampleHigh)\n"
);
ide_bus_offset[l] = -ATA_STATUS;
}
devbusfn = pci_find_device (0x1103, 0x0004, 0);
+ if (devbusfn == -1)
+ devbusfn = pci_find_device (0x1095, 0x3114, 0);
if (devbusfn != -1) {
status = 0;
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o flash.o ../common/misc.o ../common/auto_update.o
+COBJS = $(BOARD).o flash.o \
+ ../common/misc.o \
+ ../common/esd405ep_nand.o \
+ ../common/auto_update.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
* (C) Copyright 2005
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
- * (C) Copyright 2006
+ * (C) Copyright 2006-2007
* Matthias Fuchs, esd GmbH, matthias.fuchs@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
/*
- * Set NAND-FLASH GPIO signals to default
- */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
- /*
* Reset touch-screen controller
*/
out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_TOUCH_RST);
#endif /* CONFIG_IDE_RESET */
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
- nand_probe(CFG_NAND_BASE);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-}
-#endif
-
-
#if defined(CFG_EEPROM_WREN)
/* Input: <dev_addr> I2C address of EEPROM device to enable.
* <state> -1: deliver current state
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o flash.o ../common/misc.o
+COBJS = $(BOARD).o flash.o \
+ ../common/misc.o \
+ ../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
out32(GPIO0_OR, val);
/*
- * Set NAND-FLASH GPIO signals to default
- */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
- /*
* check board type and setup AP power
*/
str = getenv("bd_type"); /* this is only set on non prototype hardware */
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
-#if 0
- printf("\nmb0cf=%x\n", val); /* test-only */
- printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
-
-
-int testdram (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("test: 16 MB - ok\n");
-
- return (0);
-}
-
-
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
- nand_probe(CFG_NAND_BASE);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-}
-#endif
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o flash.o ../common/misc.o ../common/auto_update.o
+COBJS = $(BOARD).o flash.o \
+ ../common/misc.o \
+ ../common/esd405ep_nand.o \
+ ../common/auto_update.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
#include <common.h>
#include <asm/processor.h>
+#include <asm/io.h>
#include <command.h>
#include <malloc.h>
#define FPGA_DEBUG
#endif
+DECLARE_GLOBAL_DATA_PTR;
+
extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
extern void lxt971_no_sleep(void);
int index;
int i;
+ /* adjust flash start and offset */
+ gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+ gd->bd->bi_flashoffset = 0;
+
dst = malloc(CFG_FPGA_MAX_SIZE);
if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
printf ("GUNZIP ERROR - must RESET board to recover\n");
/*
* Reset external DUARTs
*/
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_DUART_RST);
udelay(10); /* wait 10us */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
+ out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_DUART_RST);
udelay(1000); /* wait 1ms */
/*
- * Set NAND-FLASH GPIO signals to default
- */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
- /*
* Enable interrupts in exar duart mcr[3]
*/
*duart0_mcr = 0x08;
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
-#if 0
- printf("\nmb0cf=%x\n", val); /* test-only */
- printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
-int testdram (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("test: 16 MB - ok\n");
-
- return (0);
-}
-
-
#ifdef CONFIG_IDE_RESET
void ide_set_reset(int on)
{
#endif /* CONFIG_IDE_RESET */
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
- nand_probe(CFG_NAND_BASE);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-}
-#endif
-
-
-#ifdef CONFIG_AUTO_UPDATE_SHOW
-void board_auto_update_show(int au_active)
-{
- if (au_active) {
- printf("\n Dies ist die board-funktion: Updating!!!\n");
- } else {
- printf("\n Dies ist die board-funktion: Updating done!!!\n");
- }
-}
-#endif
-
void reset_phy(void)
{
#ifdef CONFIG_LXT971_NO_SLEEP
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o flash.o ../common/misc.o
+COBJS = $(BOARD).o flash.o \
+ ../common/misc.o \
+ ../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
udelay(1000); /* wait 1ms */
/*
- * Set NAND-FLASH GPIO signals to default
- */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
- /*
* Enable interrupts in exar duart mcr[3]
*/
*duart0_mcr = 0x08;
}
}
#endif /* CONFIG_IDE_RESET */
-
-
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
- nand_probe(CFG_NAND_BASE);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-}
-#endif
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o flash.o ../common/misc.o
+COBJS = $(BOARD).o flash.o \
+ ../common/misc.o \
+ ../common/esd405ep_nand.o \
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
udelay(1000); /* wait 1ms */
/*
- * Set NAND-FLASH GPIO signals to default
- */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
- /*
* Enable interrupts in exar duart mcr[3]
*/
*duart0_mcr = 0x08;
mtdcr(memcfga, mem_mb0cf);
val = mfdcr(memcfgd);
-#if 0
- printf("\nmb0cf=%x\n", val); /* test-only */
- printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
-
-/* ------------------------------------------------------------------------- */
-
-int testdram (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("test: 16 MB - ok\n");
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
- nand_probe(CFG_NAND_BASE);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-}
-#endif
#undef CONFIG_BOOTARGS
#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#if !defined(CONFIG_MPC885ADS)
#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
+#endif
/*
* New MPC86xADS and MPC885ADS provide two Ethernet connectivity options:
include $(TOPDIR)/config.mk
ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../freescale/common)
+$(shell mkdir -p $(obj)../common)
endif
LIB = $(obj)lib$(BOARD).a
-COBJS := $(BOARD).o sys_eeprom.o \
- ../freescale/common/pixis.o
+COBJS := $(BOARD).o \
+ ../common/sys_eeprom.o \
+ ../common/pixis.o
SOBJS := init.o
extern void ft_cpu_setup(void *blob, bd_t *bd);
#endif
-#include "../freescale/common/pixis.h"
+#include "../common/pixis.h"
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
.text :
{
cpu/mpc86xx/start.o (.text)
- board/mpc8641hpcn/init.o (.bootpg)
+ board/freescale/mpc8641hpcn/init.o (.bootpg)
cpu/mpc86xx/traps.o (.text)
cpu/mpc86xx/interrupts.o (.text)
cpu/mpc86xx/cpu_init.o (.text)
initrd_end = 0;
}
+#if defined(CONFIG_OF_LIBFDT)
+
#ifdef CFG_BOOTMAPSZ
/*
* The blob must be within CFG_BOOTMAPSZ,
- * so we flag it to be copied if it is
+ * so we flag it to be copied if it is not.
*/
if (of_flat_tree >= (char *)CFG_BOOTMAPSZ)
- of_data = of_flat_tree;
+ of_data = (ulong)of_flat_tree;
#endif
-#if defined(CONFIG_OF_LIBFDT)
/* move of_flat_tree if needed */
if (of_data) {
int err;
#endif
#endif /* CONFIG_OF_LIBFDT */
#if defined(CONFIG_OF_FLAT_TREE)
+#ifdef CFG_BOOTMAPSZ
+ /*
+ * The blob must be within CFG_BOOTMAPSZ,
+ * so we flag it to be copied if it is not.
+ */
+ if (of_flat_tree >= (char *)CFG_BOOTMAPSZ)
+ of_data = (ulong)of_flat_tree;
+#endif
+
/* move of_flat_tree if needed */
if (of_data) {
ulong of_start, of_len;
ulong offset, ulong addr, char *cmd)
{
int r;
- char *ep;
+ char *ep, *s;
ulong cnt;
image_header_t *hdr;
+ int jffs2 = 0;
+
+ s = strchr(cmd, '.');
+ if (s != NULL &&
+ (!strcmp(s, ".jffs2") || !strcmp(s, ".e") || !strcmp(s, ".i")))
+ jffs2 = 1;
printf("\nLoading from %s, offset 0x%lx\n", nand->name, offset);
cnt = nand->oobblock;
- r = nand_read(nand, offset, &cnt, (u_char *) addr);
+ if (jffs2) {
+ nand_read_options_t opts;
+ memset(&opts, 0, sizeof(opts));
+ opts.buffer = (u_char*) addr;
+ opts.length = cnt;
+ opts.offset = offset;
+ opts.quiet = 1;
+ r = nand_read_opts(nand, &opts);
+ } else {
+ r = nand_read(nand, offset, &cnt, (u_char *) addr);
+ }
+
if (r) {
puts("** Read error\n");
show_boot_progress (-56);
print_image_hdr(hdr);
cnt = (ntohl(hdr->ih_size) + sizeof (image_header_t));
+ if (jffs2) {
+ nand_read_options_t opts;
+ memset(&opts, 0, sizeof(opts));
+ opts.buffer = (u_char*) addr;
+ opts.length = cnt;
+ opts.offset = offset;
+ opts.quiet = 1;
+ r = nand_read_opts(nand, &opts);
+ } else {
+ r = nand_read(nand, offset, &cnt, (u_char *) addr);
+ }
- r = nand_read(nand, offset, &cnt, (u_char *) addr);
if (r) {
puts("** Read error\n");
show_boot_progress (-58);
if (argc > 3)
goto usage;
if (argc == 3)
- addr = simple_strtoul(argv[2], NULL, 16);
+ addr = simple_strtoul(argv[1], NULL, 16);
else
addr = CFG_LOAD_ADDR;
return nand_load_image(cmdtp, &nand_info[dev->id->num],
U_BOOT_CMD(nboot, 4, 1, do_nandboot,
"nboot - boot from NAND device\n",
- "[partition] | [[[loadAddr] dev] offset]\n");
+ "[.jffs2] [partition] | [[[loadAddr] dev] offset]\n");
#endif
int fdt_chosen(void *fdt, ulong initrd_start, ulong initrd_end, int force)
{
- bd_t *bd = gd->bd;
int nodeoffset;
int err;
u32 tmp; /* used to set 32 bit integer properties */
*
****************************************************************************/
-#include "biosemui.h"
+#include <common.h>
#if defined(CONFIG_BIOSEMU)
+
+#include "biosemui.h"
+
/*------------------------- Global Variables ------------------------------*/
#ifndef __i386__
*
****************************************************************************/
-#include "biosemui.h"
+#include <common.h>
#if defined(CONFIG_BIOSEMU)
+
+#include "biosemui.h"
+
/*----------------------------- Implementation ----------------------------*/
/****************************************************************************
*
****************************************************************************/
-#include "biosemui.h"
#include <malloc.h>
+#include <common.h>
#if defined(CONFIG_BIOSEMU)
+#include "biosemui.h"
+
BE_sysEnv _BE_env = {{0}};
static X86EMU_memFuncs _BE_mem __attribute__((section(".got2"))) = {
BE_rdb,
*
****************************************************************************/
-#include "x86emu/x86emui.h"
#include <stdarg.h>
+#include <common.h>
#if defined(CONFIG_BIOSEMU)
+#include "x86emu/x86emui.h"
+
/*----------------------------- Implementation ----------------------------*/
#ifdef DEBUG
* instruction decoding and accessess of immediate data via IP. etc.
*
****************************************************************************/
-
-#include "x86emu/x86emui.h"
+#include <common.h>
#if defined(CONFIG_BIOSEMU)
+#include "x86emu/x86emui.h"
+
/*----------------------------- Implementation ----------------------------*/
/****************************************************************************
*
****************************************************************************/
-#include "x86emu/x86emui.h"
+#include <common.h>
#if defined(CONFIG_BIOSEMU)
+#include "x86emu/x86emui.h"
+
/*----------------------------- Implementation ----------------------------*/
/* constant arrays to do several instructions in just one function */
*
****************************************************************************/
-#include "x86emu/x86emui.h"
+#include <common.h>
#if defined(CONFIG_BIOSEMU)
+#include "x86emu/x86emui.h"
+
/*----------------------------- Implementation ----------------------------*/
/****************************************************************************
*
****************************************************************************/
+#include <common.h>
+
#define PRIM_OPS_NO_REDEFINE_ASM
-#include "x86emu/x86emui.h"
#if defined(CONFIG_BIOSEMU)
+#include "x86emu/x86emui.h"
+
/*------------------------- Global Variables ------------------------------*/
static u32 x86emu_parity_tab[8] =
*
****************************************************************************/
-#include "x86emu/x86emui.h"
+#include <common.h>
#if defined(CONFIG_BIOSEMU)
+#include "x86emu/x86emui.h"
+
/*------------------------- Global Variables ------------------------------*/
X86EMU_sysEnv _X86EMU_env; /* Global emulator machine state */
{NAND_MFR_NATIONAL, "National"},
{NAND_MFR_RENESAS, "Renesas"},
{NAND_MFR_STMICRO, "ST Micro"},
+ {NAND_MFR_MICRON, "Micron"},
{0x0, "Unknown"}
};
#endif
if (dev->enetaddr[0] & 0x01) {
printf("%s: MacAddress is multcast address\n",
__FUNCTION__);
- return -EINVAL;
+ return 0;
}
uec_set_mac_address(uec, dev->enetaddr);
uec->the_first_run = 1;
err = uec_open(uec, COMM_DIR_RX_AND_TX);
if (err) {
printf("%s: cannot enable UEC device\n", dev->name);
- return err;
+ return 0;
}
- return 0;
+ return uec->mii_info->link;
}
static void uec_halt(struct eth_device* dev)
* FEC_PHYIDX
*/
static struct tsec_info_struct tsec_info[] = {
-#if defined(CONFIG_TSEC1)
-#if defined(CONFIG_MPC8544DS) || defined(CONFIG_MPC8641HPCN)
- {TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX},
-#else
- {TSEC1_PHY_ADDR, TSEC_GIGABIT, TSEC1_PHYIDX},
-#endif
+#ifdef CONFIG_TSEC1
+ {TSEC1_PHY_ADDR, TSEC1_FLAGS, TSEC1_PHYIDX},
#else
{0, 0, 0},
#endif
-#if defined(CONFIG_TSEC2)
-#if defined(CONFIG_MPC8641HPCN)
- {TSEC2_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC2_PHYIDX},
-#else
- {TSEC2_PHY_ADDR, TSEC_GIGABIT, TSEC2_PHYIDX},
-#endif
+#ifdef CONFIG_TSEC2
+ {TSEC2_PHY_ADDR, TSEC2_FLAGS, TSEC2_PHYIDX},
#else
{0, 0, 0},
#endif
#ifdef CONFIG_MPC85XX_FEC
- {FEC_PHY_ADDR, 0, FEC_PHYIDX},
+ {FEC_PHY_ADDR, FEC_FLAGS, FEC_PHYIDX},
#else
-#if defined(CONFIG_TSEC3)
- {TSEC3_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC3_PHYIDX},
+#ifdef CONFIG_TSEC3
+ {TSEC3_PHY_ADDR, TSEC3_FLAGS, TSEC3_PHYIDX},
#else
{0, 0, 0},
#endif
-#if defined(CONFIG_TSEC4)
- {TSEC4_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC4_PHYIDX},
+#ifdef CONFIG_TSEC4
+ {TSEC4_PHY_ADDR, TSEC4_FLAGS, TSEC4_PHYIDX},
#else
{0, 0, 0},
-#endif
-#endif
+#endif /* CONFIG_TSEC4 */
+#endif /* CONFIG_MPC85XX_FEC */
};
#define MAXCONTROLLERS (4)
uint mii_parse_sr(uint mii_reg, struct tsec_private * priv)
{
/*
- * Wait if PHY is capable of autonegotiation and autonegotiation
- * is not complete.
+ * Wait if the link is up, and autonegotiation is in progress
+ * (ie - we're capable and it's not done)
*/
mii_reg = read_phy_reg(priv, MIIM_STATUS);
- if ((mii_reg & PHY_BMSR_AUTN_ABLE)
+ if ((mii_reg & MIIM_STATUS_LINK) && (mii_reg & PHY_BMSR_AUTN_ABLE)
&& !(mii_reg & PHY_BMSR_AUTN_COMP)) {
int i = 0;
puts("Waiting for PHY auto negotiation to complete");
- while (!((mii_reg & PHY_BMSR_AUTN_COMP)
- && (mii_reg & MIIM_STATUS_LINK))) {
+ while (!(mii_reg & PHY_BMSR_AUTN_COMP)) {
/*
* Timeout reached ?
*/
priv->link = 1;
udelay(500000); /* another 500 ms (results in faster booting) */
} else {
- priv->link = 1;
+ if (mii_reg & MIIM_STATUS_LINK)
+ priv->link = 1;
+ else
+ priv->link = 0;
}
return 0;
mii_reg = read_phy_reg(priv, MIIM_88E1011_PHY_STATUS);
- if (!((mii_reg & MIIM_88E1011_PHYSTAT_SPDDONE) &&
- (mii_reg & MIIM_88E1011_PHYSTAT_LINK))) {
+ if ((mii_reg & MIIM_88E1011_PHYSTAT_LINK) &&
+ !(mii_reg & MIIM_88E1011_PHYSTAT_SPDDONE)) {
int i = 0;
puts("Waiting for PHY realtime link");
- while (!((mii_reg & MIIM_88E1011_PHYSTAT_SPDDONE) &&
- (mii_reg & MIIM_88E1011_PHYSTAT_LINK))) {
- /*
- * Timeout reached ?
- */
+ while (!(mii_reg & MIIM_88E1011_PHYSTAT_SPDDONE)) {
+ /* Timeout reached ? */
if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
puts(" TIMEOUT !\n");
priv->link = 0;
}
puts(" done\n");
udelay(500000); /* another 500 ms (results in faster booting) */
+ } else {
+ if (mii_reg & MIIM_88E1011_PHYSTAT_LINK)
+ priv->link = 1;
+ else
+ priv->link = 0;
}
if (mii_reg & MIIM_88E1011_PHYSTAT_DUPLEX)
uint svr; /* 0xe00a4 - System version register */
char res10a[8];
uint rstcr; /* 0xe00b0 - Reset control register */
-#ifdef MPC8568
+#ifdef CONFIG_MPC8568
char res10b[76];
par_io_t qe_par_io[7]; /* 0xe0100 - 0xe01bf */
char res10c[3136];
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_NET_MULTI 1
+#undef CONFIG_HAS_ETH1
+
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS 1
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US 25
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
/*-----------------------------------------------------------------------
#define CONFIG_CMD_EEPROM
-#define CFG_NAND_LEGACY
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS 1
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US 25
+
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
#define CONFIG_SUPPORT_VFAT
-#define CFG_NAND_LEGACY
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
#endif
-#define CFG_NAND_LEGACY
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#define CONFIG_SUPPORT_VFAT
-#define CFG_NAND_LEGACY
-
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#undef CONFIG_AUTO_UPDATE /* autoupdate via compactflash */
-#define CFG_NAND_LEGACY
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
#undef CONFIG_AUTO_UPDATE_SHOW /* use board show routine */
-#define CFG_NAND_LEGACY
-
#undef CONFIG_BZIP2 /* include support for bzip2 compressed images */
#undef CONFIG_WATCHDOG /* watchdog disabled */
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS 1
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US 25
+
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS 1
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US 25
+
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
#define CONFIG_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 0x1c
#define TSEC2_PHY_ADDR 4
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CFG_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 0x1c /* VSC8201 uses address 0x1c */
#define TSEC1_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
#endif
#ifdef CONFIG_TSEC2
#define CONFIG_UNKNOWN_TSEC /* TSEC2 is proprietary */
#define TSEC2_PHY_ADDR 4
#define TSEC2_PHYIDX 0
+#define TSEC2_FLAGS TSEC_GIGABIT
#endif
#define CONFIG_ETHPRIME "Freescale TSEC"
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
#if CONFIG_HAS_FEC
#define CONFIG_MPC85XX_FEC_NAME "FEC"
#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
+#define FEC_FLAGS 0
#endif
/* Options are: TSEC[0-1], FEC */
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define FEC_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define FEC_FLAGS 0
+
/* Options are: TSEC[0-1], FEC */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
-#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
-#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
-#define FEC_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "eTSEC3"
-#undef CONFIG_MPC85XX_FEC
-
-#define CONFIG_TSEC_TBI 1 /* enable internal TBI phy */
-#define CONFIG_SGMII_RISER
-#define TSEC1_SGMII_PHY_ADDR_OFFSET 0x1c /* sgmii phy base */
#define TSEC1_PHY_ADDR 0
#define TSEC3_PHY_ADDR 1
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+
#define TSEC1_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
/* Options are: eTSEC[0-3] */
#define CONFIG_ETHPRIME "eTSEC0"
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
-#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
-#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
-#define FEC_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
-#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_QE /* Enable QE */
+#define CONFIG_QE /* Enable QE */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_DLL /* possible DLL fix needed */
*/
#define CONFIG_UEC_ETH
#ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_ETHPRIME "FSL UEC0"
#endif
#define CONFIG_PHY_MODE_NEED_CHANGE
#define CONFIG_eTSEC_MDIO_BUS
#define CONFIG_TSEC1_NAME "eTSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC1"
-#undef CONFIG_TSEC3
-#undef CONFIG_TSEC4
-#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
-/* Options are: eTSEC[0-3] */
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+
+/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME "eTSEC0"
#endif /* CONFIG_TSEC_ENET */
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define CONFIG_ETHPRIME "eTSEC1"
#define CONFIG_SUPPORT_VFAT
#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
-#define CONFIG_AUTO_UPDATE_SHOW 1 /* use board show routine */
#undef CONFIG_WATCHDOG /* watchdog disabled */
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
-#define CFG_NAND_LEGACY
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS 1
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US 25
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
-#endif
-
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
-#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
-
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
*/
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */
-#if 1 /* test-only */
+
/* CAT24WC08/16... */
#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
/* last 4 bits of the address */
-#else
-/* CAT24WC32/64... */
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
- /* 32 byte page write mode using*/
- /* last 5 bits of the address */
-#endif
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
#define CONFIG_MPC85XX_FEC 1
#define CONFIG_MPC85XX_FEC_NAME "FEC"
#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
+#define FEC_FLAGS 0
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
-#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
#endif /* CONFIG_TSEC_ENET */
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
+#define FEC_FLAGS 0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS 1
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US 25
+
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS 1
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US 25
+
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+
#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
/*-----------------------------------------------------------------------
#define TSEC2_PHY_ADDR 0x1a
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define TSEC3_FLAGS TSEC_GIGABIT
+#define TSEC4_FLAGS TSEC_GIGABIT
#define CFG_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
-#undef CONFIG_MPS85XX_FEC
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 4
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
#define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
-#define CONFIG_MPS85XX_FEC
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 4
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
#define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
#define NAND_MFR_NATIONAL 0x8f
#define NAND_MFR_RENESAS 0x07
#define NAND_MFR_STMICRO 0x20
+#define NAND_MFR_MICRON 0x2c
/**
* struct nand_flash_dev - NAND Flash Device ID Structure
extern int nand_curr_device;
extern nand_info_t nand_info[];
+extern void nand_init(void);
static inline int nand_read(nand_info_t *info, ulong ofs, ulong *len, u_char *buf)
{
#endif /* Multicast TFTP */
-#endif /* CFG_CMD_NET */
+#endif
projects / platform / kernel / u-boot.git / commitdiff