Input: add I2C attached EETI EXC3000 multi touch driver

The 3000 series have a new protocol which allows to report up to 5 points
in a single 66 byte frame. One must always read in 66 byte frames.
To support up to 10 points, two consecutive frames need to be read:
The first frame says how many points until sync.
The second frame must say zero points or both frames must be discarded.

To be able to work with the higher 400KHz I2C bus rate, one must
successfully send a special package prior _each_ read or the controller
will refuse to cooperate.

This is a minimal implementation based on egalax_i2c.c (which can be found
on the internet) and egalax_ts.c but without the vendor interface and no
power management support.

Signed-off-by: Ahmet Inan <inan@distec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

diff --git a/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt b/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt
new file mode 100644 (file)
index 0000000..1dcff4a
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt
@@ -0,0 +1,27 @@
+* EETI EXC3000 Multiple Touch Controller
+
+Required properties:
+- compatible: must be "eeti,exc3000"
+- reg: i2c slave address
+- interrupt-parent: the phandle for the interrupt controller
+- interrupts: touch controller interrupt
+- touchscreen-size-x: See touchscreen.txt
+- touchscreen-size-y: See touchscreen.txt
+
+Optional properties:
+- touchscreen-inverted-x: See touchscreen.txt
+- touchscreen-inverted-y: See touchscreen.txt
+- touchscreen-swapped-x-y: See touchscreen.txt
+
+Example:
+
+       touchscreen@2a {
+               compatible = "eeti,exc3000";
+               reg = <0x2a>;
+               interrupt-parent = <&gpio1>;
+               interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+               touchscreen-size-x = <4096>;
+               touchscreen-size-y = <4096>;
+               touchscreen-inverted-x;
+               touchscreen-swapped-x-y;
+       };

diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 16cadc1..26a66bc 100644 (file)
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -316,6 +316,16 @@ config TOUCHSCREEN_EGALAX_SERIAL
          To compile this driver as a module, choose M here: the
          module will be called egalax_ts_serial.
 
+config TOUCHSCREEN_EXC3000
+       tristate "EETI EXC3000 multi-touch panel support"
+       depends on I2C
+       help
+         Say Y here to enable support for I2C connected EETI
+         EXC3000 multi-touch panels.
+
+         To compile this driver as a module, choose M here: the
+         module will be called exc3000.
+
 config TOUCHSCREEN_FUJITSU
        tristate "Fujitsu serial touchscreen"
        select SERIO

diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 6badce8..a129df6 100644 (file)
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -37,6 +37,7 @@ obj-$(CONFIG_TOUCHSCREEN_ELAN)                += elants_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ELO)          += elo.o
 obj-$(CONFIG_TOUCHSCREEN_EGALAX)       += egalax_ts.o
 obj-$(CONFIG_TOUCHSCREEN_EGALAX_SERIAL)        += egalax_ts_serial.o
+obj-$(CONFIG_TOUCHSCREEN_EXC3000)      += exc3000.o
 obj-$(CONFIG_TOUCHSCREEN_FUJITSU)      += fujitsu_ts.o
 obj-$(CONFIG_TOUCHSCREEN_GOODIX)       += goodix.o
 obj-$(CONFIG_TOUCHSCREEN_ILI210X)      += ili210x.o

diff --git a/drivers/input/touchscreen/exc3000.c b/drivers/input/touchscreen/exc3000.c
new file mode 100644 (file)
index 0000000..37437a5
--- /dev/null
+++ b/drivers/input/touchscreen/exc3000.c
@@ -0,0 +1,223 @@
+/*
+ * Driver for I2C connected EETI EXC3000 multiple touch controller
+ *
+ * Copyright (C) 2017 Ahmet Inan <inan@distec.de>
+ *
+ * minimal implementation based on egalax_ts.c and egalax_i2c.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/timer.h>
+#include <asm/unaligned.h>
+
+#define EXC3000_NUM_SLOTS              10
+#define EXC3000_SLOTS_PER_FRAME                5
+#define EXC3000_LEN_FRAME              66
+#define EXC3000_LEN_POINT              10
+#define EXC3000_MT_EVENT               6
+#define EXC3000_TIMEOUT_MS             100
+
+struct exc3000_data {
+       struct i2c_client *client;
+       struct input_dev *input;
+       struct touchscreen_properties prop;
+       struct timer_list timer;
+       u8 buf[2 * EXC3000_LEN_FRAME];
+};
+
+static void exc3000_report_slots(struct input_dev *input,
+                                struct touchscreen_properties *prop,
+                                const u8 *buf, int num)
+{
+       for (; num--; buf += EXC3000_LEN_POINT) {
+               if (buf[0] & BIT(0)) {
+                       input_mt_slot(input, buf[1]);
+                       input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
+                       touchscreen_report_pos(input, prop,
+                                              get_unaligned_le16(buf + 2),
+                                              get_unaligned_le16(buf + 4),
+                                              true);
+               }
+       }
+}
+
+static void exc3000_timer(struct timer_list *t)
+{
+       struct exc3000_data *data = from_timer(data, t, timer);
+
+       input_mt_sync_frame(data->input);
+       input_sync(data->input);
+}
+
+static int exc3000_read_frame(struct i2c_client *client, u8 *buf)
+{
+       int ret;
+
+       ret = i2c_master_send(client, "'", 2);
+       if (ret < 0)
+               return ret;
+
+       if (ret != 2)
+               return -EIO;
+
+       ret = i2c_master_recv(client, buf, EXC3000_LEN_FRAME);
+       if (ret < 0)
+               return ret;
+
+       if (ret != EXC3000_LEN_FRAME)
+               return -EIO;
+
+       if (get_unaligned_le16(buf) != EXC3000_LEN_FRAME ||
+                       buf[2] != EXC3000_MT_EVENT)
+               return -EINVAL;
+
+       return 0;
+}
+
+static int exc3000_read_data(struct i2c_client *client,
+                            u8 *buf, int *n_slots)
+{
+       int error;
+
+       error = exc3000_read_frame(client, buf);
+       if (error)
+               return error;
+
+       *n_slots = buf[3];
+       if (!*n_slots || *n_slots > EXC3000_NUM_SLOTS)
+               return -EINVAL;
+
+       if (*n_slots > EXC3000_SLOTS_PER_FRAME) {
+               /* Read 2nd frame to get the rest of the contacts. */
+               error = exc3000_read_frame(client, buf + EXC3000_LEN_FRAME);
+               if (error)
+                       return error;
+
+               /* 2nd chunk must have number of contacts set to 0. */
+               if (buf[EXC3000_LEN_FRAME + 3] != 0)
+                       return -EINVAL;
+       }
+
+       return 0;
+}
+
+static irqreturn_t exc3000_interrupt(int irq, void *dev_id)
+{
+       struct exc3000_data *data = dev_id;
+       struct input_dev *input = data->input;
+       u8 *buf = data->buf;
+       int slots, total_slots;
+       int error;
+
+       error = exc3000_read_data(data->client, buf, &total_slots);
+       if (error) {
+               /* Schedule a timer to release "stuck" contacts */
+               mod_timer(&data->timer,
+                         jiffies + msecs_to_jiffies(EXC3000_TIMEOUT_MS));
+               goto out;
+       }
+
+       /*
+        * We read full state successfully, no contacts will be "stuck".
+        */
+       del_timer_sync(&data->timer);
+
+       while (total_slots > 0) {
+               slots = min(total_slots, EXC3000_SLOTS_PER_FRAME);
+               exc3000_report_slots(input, &data->prop, buf + 4, slots);
+               total_slots -= slots;
+               buf += EXC3000_LEN_FRAME;
+       }
+
+       input_mt_sync_frame(input);
+       input_sync(input);
+
+out:
+       return IRQ_HANDLED;
+}
+
+static int exc3000_probe(struct i2c_client *client,
+                        const struct i2c_device_id *id)
+{
+       struct exc3000_data *data;
+       struct input_dev *input;
+       int error;
+
+       data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
+       if (!data)
+               return -ENOMEM;
+
+       data->client = client;
+       timer_setup(&data->timer, exc3000_timer, 0);
+
+       input = devm_input_allocate_device(&client->dev);
+       if (!input)
+               return -ENOMEM;
+
+       data->input = input;
+
+       input->name = "EETI EXC3000 Touch Screen";
+       input->id.bustype = BUS_I2C;
+
+       input_set_abs_params(input, ABS_MT_POSITION_X, 0, 4095, 0, 0);
+       input_set_abs_params(input, ABS_MT_POSITION_Y, 0, 4095, 0, 0);
+       touchscreen_parse_properties(input, true, &data->prop);
+
+       error = input_mt_init_slots(input, EXC3000_NUM_SLOTS,
+                                   INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
+       if (error)
+               return error;
+
+       error = input_register_device(input);
+       if (error)
+               return error;
+
+       error = devm_request_threaded_irq(&client->dev, client->irq,
+                                         NULL, exc3000_interrupt, IRQF_ONESHOT,
+                                         client->name, data);
+       if (error)
+               return error;
+
+       return 0;
+}
+
+static const struct i2c_device_id exc3000_id[] = {
+       { "exc3000", 0 },
+       { }
+};
+MODULE_DEVICE_TABLE(i2c, exc3000_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id exc3000_of_match[] = {
+       { .compatible = "eeti,exc3000" },
+       { }
+};
+MODULE_DEVICE_TABLE(of, exc3000_of_match);
+#endif
+
+static struct i2c_driver exc3000_driver = {
+       .driver = {
+               .name   = "exc3000",
+               .of_match_table = of_match_ptr(exc3000_of_match),
+       },
+       .id_table       = exc3000_id,
+       .probe          = exc3000_probe,
+};
+
+module_i2c_driver(exc3000_driver);
+
+MODULE_AUTHOR("Ahmet Inan <inan@distec.de>");
+MODULE_DESCRIPTION("I2C connected EETI EXC3000 multiple touch controller driver");
+MODULE_LICENSE("GPL v2");