Synchronise device tree with linux v6.0-rc1.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
pinctrl-0 = <&spi2_pins_a>;
status = "okay";
- flash: m25p80@0 {
+ flash: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "sst,sst25vf016b", "jedec,spi-nor";
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2021
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+ aliases {
+ spi2 = &ssp3;
+ };
+
+ chosen {
+ bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1";
+ };
+
+ memory@40000000 {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ reg_3v3: regulator-reg-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_usb_5v: regulator-reg-usb-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_fec_3v3: regulator-reg-fec-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "fec-phy";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ #sound-dai-cells = <0>;
+ assigned-clocks = <&clks 53>;
+ assigned-clock-rates = <12000000>;
+ status = "okay";
+};
+
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ #sound-dai-cells = <0>;
+ status = "okay";
+};
+
+&spi3_pins_a {
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART2_RX__SSP3_D4
+ MX28_PAD_AUART2_TX__SSP3_D5
+ MX28_PAD_SSP3_SCK__SSP3_SCK
+ MX28_PAD_SSP3_MOSI__SSP3_CMD
+ MX28_PAD_SSP3_MISO__SSP3_D0
+ MX28_PAD_SSP3_SS0__SSP3_D3
+ MX28_PAD_AUART2_TX__GPIO_3_9
+ >;
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a>;
+ bus-width = <8>;
+ vmmc-supply = <®_3v3>;
+ non-removable;
+ status = "okay";
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+};
+
+&ssp3 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_pins_a>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "env0";
+ reg = <0x80000 0x10000>;
+ };
+
+ partition@90000 {
+ label = "env1";
+ reg = <0x90000 0x10000>;
+ };
+
+ partition@100000 {
+ label = "kernel";
+ reg = <0x100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "swupdate";
+ reg = <0x500000 0x800000>;
+ };
+ };
+ };
+};
+
+&usb0 {
+ vbus-supply = <®_usb_5v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_pins_b>, <&usb0_id_pins_a>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb_5v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_pins_b>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Header providing constants for i.MX28 pinctrl bindings.
*
* Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#ifndef __DT_BINDINGS_MX28_PINCTRL_H__
-// SPDX-License-Identifier: GPL-2.0+
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
- * Copyright 2019
+ * Copyright 2021
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+ or X11
- *
*/
/dts-v1/;
-
-#include "imx28.dtsi"
+#include "imx28-lwe.dtsi"
/ {
- model = "Liebherr (LWE) XEA i.MX28 Board";
- compatible = "lwe,xea", "fsl,imx28";
-
- aliases {
- spi3 = &ssp3;
- };
-
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x10000000>;
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_fec_3v3: regulator-fec-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "fec-3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio0 0 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- };
-
- reg_usb_5v: regulator-usb-5v {
- compatible = "regulator-fixed";
- regulator-name = "usb_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ compatible = "lwn,imx28-xea", "fsl,imx28";
};
-&mac0 {
- phy-mode = "rmii";
+&can0 {
pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-supply = <®_fec_3v3>;
- phy-reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <1>;
- phy-reset-post-delay = <1>;
+ pinctrl-0 = <&can1_pins_a>;
status = "okay";
-
- fixed-link {
- speed = <100>;
- full-duplex;
- };
};
-&ssp0 {
- compatible = "fsl,imx28-mmc";
+&i2c1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- non-removable;
+ pinctrl-0 = <&i2c1_pins_b>;
status = "okay";
};
-&ssp3 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
+&pinctrl {
pinctrl-names = "default";
- pinctrl-0 = <&spi3_pins_b>;
- status = "okay";
- spi-max-frequency = <40000000>;
- num-cs = <2>;
+ pinctrl-0 = <&hog_pins_a &hog_pins_tiva>;
- flash0: s25fl256s@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "jedec,spi-nor";
- spi-max-frequency = <40000000>;
+ hog_pins_a: hog@0 {
reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D00__GPIO_0_0
+ MX28_PAD_GPMI_D02__GPIO_0_2
+ MX28_PAD_GPMI_D05__GPIO_0_5
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_RDY0__GPIO_0_20
+ MX28_PAD_GPMI_RDY1__GPIO_0_21
+ MX28_PAD_GPMI_RDY2__GPIO_0_22
+ MX28_PAD_GPMI_RDN__GPIO_0_24
+ MX28_PAD_GPMI_CLE__GPIO_0_27
+ MX28_PAD_LCD_VSYNC__GPIO_1_28
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP2_SS1__GPIO_2_20
+ MX28_PAD_SSP2_SS2__GPIO_2_21
+ MX28_PAD_LCD_D00__GPIO_1_0
+ MX28_PAD_LCD_D01__GPIO_1_1
+ MX28_PAD_LCD_D02__GPIO_1_2
+ MX28_PAD_LCD_D03__GPIO_1_3
+ MX28_PAD_LCD_D04__GPIO_1_4
+ MX28_PAD_LCD_D05__GPIO_1_5
+ MX28_PAD_LCD_D06__GPIO_1_6
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ hog_pins_tiva: hog@1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_RDY3__GPIO_0_23
+ MX28_PAD_GPMI_WRN__GPIO_0_25
+ >;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
- partition@0 {
- label = "SPL";
- reg = <0x0 0x10000>;
- read-only;
- };
- partition@10000 {
- label = "u-boot";
- reg = <0x10000 0x70000>;
- read-only;
- };
- partition@80000 {
- label = "uboot-env1";
- reg = <0x80000 0x10000>;
- };
- partition@90000 {
- label = "uboot-env2";
- reg = <0x90000 0x10000>;
- };
- partition@A0000 {
- label = "rescue";
- reg = <0xA0000 0xF40000>;
- };
- partition@FE0000 {
- label = "spl-boot-data1";
- reg = <0xFE0000 0x10000>;
- };
- partition@FF0000 {
- label = "spl-boot-data2";
- reg = <0xFF0000 0x10000>;
- };
- };
+ hog_pins_coding: hog@2 {
+ reg = <2>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D01__GPIO_0_1
+ MX28_PAD_GPMI_D03__GPIO_0_3
+ MX28_PAD_GPMI_D04__GPIO_0_4
+ MX28_PAD_GPMI_D06__GPIO_0_6
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
-&usb0 {
- vbus-supply = <®_usb_5v>;
- status = "okay";
+®_fec_3v3 {
+ gpio = <&gpio0 0 0>;
};
-&usbphy0 {
- status = "okay";
+®_usb_5v {
+ gpio = <&gpio0 2 0>;
+};
+
+&spi2_pins_a {
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__SSP2_SCK
+ MX28_PAD_SSP2_MOSI__SSP2_CMD
+ MX28_PAD_SSP2_MISO__SSP2_D0
+ MX28_PAD_SSP2_SS0__GPIO_2_19
+ >;
};
status = "disabled";
};
- gpmi: gpmi-nand@8000c000 {
+ gpmi: nand-controller@8000c000 {
compatible = "fsl,imx28-gpmi-nand";
#address-cells = <1>;
#size-cells = <1>;
interrupt-names = "bch";
clocks = <&clks 50>;
clock-names = "gpmi_io";
+ assigned-clocks = <&clks 13>;
+ assigned-clock-parents = <&clks 10>;
dmas = <&dma_apbh 4>;
dma-names = "rx-tx";
status = "disabled";
fsl,pull-up = <MXS_PULL_DISABLE>;
};
+ usb1_pins_b: usb1@1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ MX28_PAD_PWM2__USB1_OVERCURRENT
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
usb0_id_pins_a: usb0id@0 {
reg = <0>;
fsl,pinmux-ids = <
clocks = <&clks 26>;
};
- dcp: dcp@80028000 {
+ dcp: crypto@80028000 {
compatible = "fsl,imx28-dcp", "fsl,imx23-dcp";
reg = <0x80028000 0x2000>;
interrupts = <52 53 54>;
status = "disabled";
};
- ocotp: ocotp@8002c000 {
+ ocotp: efuse@8002c000 {
compatible = "fsl,imx28-ocotp", "fsl,ocotp";
#address-cells = <1>;
#size-cells = <1>;
status = "disabled";
};
- etn_switch: switch@800f8000 {
+ eth_switch: switch@800f8000 {
reg = <0x800f8000 0x8000>;
status = "disabled";
};
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Header providing constants for i.MX28 pinctrl bindings.
*
* Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#ifndef __DT_BINDINGS_MXS_PINCTRL_H__
projects / platform / kernel / u-boot.git / commitdiff