#define NAND_MASK (AMS_DELTA_LATCH2_NAND_NRE | AMS_DELTA_LATCH2_NAND_NWE | AMS_DELTA_LATCH2_NAND_CLE | AMS_DELTA_LATCH2_NAND_ALE | AMS_DELTA_LATCH2_NAND_NCE | AMS_DELTA_LATCH2_NAND_NWP)
-#define T_NAND_CTL_CLRALE(iob) ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_ALE, 0)
-#define T_NAND_CTL_SETALE(iob) ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_ALE, AMS_DELTA_LATCH2_NAND_ALE)
-#define T_NAND_CTL_CLRCLE(iob) ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_CLE, 0)
-#define T_NAND_CTL_SETCLE(iob) ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_CLE, AMS_DELTA_LATCH2_NAND_CLE)
-#define T_NAND_CTL_SETNCE(iob) ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NCE, 0)
-#define T_NAND_CTL_CLRNCE(iob) ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NCE, AMS_DELTA_LATCH2_NAND_NCE)
-
/*
* Define partitions for flash devices
*/
.size = 3 * SZ_256K },
};
-/*
- * hardware specific access to control-lines
-*/
-
-static void ams_delta_hwcontrol(struct mtd_info *mtd, int cmd)
-{
- switch (cmd) {
-
- case NAND_CTL_SETCLE: T_NAND_CTL_SETCLE(cmd); break;
- case NAND_CTL_CLRCLE: T_NAND_CTL_CLRCLE(cmd); break;
-
- case NAND_CTL_SETALE: T_NAND_CTL_SETALE(cmd); break;
- case NAND_CTL_CLRALE: T_NAND_CTL_CLRALE(cmd); break;
-
- case NAND_CTL_SETNCE: T_NAND_CTL_SETNCE(cmd); break;
- case NAND_CTL_CLRNCE: T_NAND_CTL_CLRNCE(cmd); break;
- }
-}
-
static void ams_delta_write_byte(struct mtd_info *mtd, u_char byte)
{
struct nand_chip *this = mtd->priv;
return 0;
}
+/*
+ * Command control function
+ *
+ * ctrl:
+ * NAND_NCE: bit 0 -> bit 2
+ * NAND_CLE: bit 1 -> bit 7
+ * NAND_ALE: bit 2 -> bit 6
+ */
+static void ams_delta_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ unsigned long bits;
+
+ bits = (~ctrl & NAND_NCE) << 2;
+ bits |= (ctrl & NAND_CLE) << 7;
+ bits |= (ctrl & NAND_ALE) << 6;
+
+ ams_delta_latch2_write(0xC2, bits);
+ }
+
+ if (cmd != NAND_CMD_NONE)
+ ams_delta_write_byte(mtd, cmd);
+}
+
static int ams_delta_nand_ready(struct mtd_info *mtd)
{
return omap_get_gpio_datain(AMS_DELTA_GPIO_PIN_NAND_RB);
this->write_buf = ams_delta_write_buf;
this->read_buf = ams_delta_read_buf;
this->verify_buf = ams_delta_verify_buf;
- this->hwcontrol = ams_delta_hwcontrol;
+ this->cmd_ctrl = ams_delta_hwcontrol;
if (!omap_request_gpio(AMS_DELTA_GPIO_PIN_NAND_RB)) {
this->dev_ready = ams_delta_nand_ready;
} else {
AMS_DELTA_LATCH2_NAND_NCE |
AMS_DELTA_LATCH2_NAND_NWP);
- /* Scan to find existance of the device */
+ /* Scan to find existance of the device */
if (nand_scan(ams_delta_mtd, 1)) {
err = -ENXIO;
goto out_mtd;
return 0;
}
+/* Select the chip by setting nCE to low */
+#define NAND_CTL_SETNCE 1
+/* Deselect the chip by setting nCE to high */
+#define NAND_CTL_CLRNCE 2
+/* Select the command latch by setting CLE to high */
+#define NAND_CTL_SETCLE 3
+/* Deselect the command latch by setting CLE to low */
+#define NAND_CTL_CLRCLE 4
+/* Select the address latch by setting ALE to high */
+#define NAND_CTL_SETALE 5
+/* Deselect the address latch by setting ALE to low */
+#define NAND_CTL_CLRALE 6
static void au1550_hwcontrol(struct mtd_info *mtd, int cmd)
{
ulong flags;
/* Begin command latch cycle */
- this->hwcontrol(mtd, NAND_CTL_SETCLE);
+ au1550_hwcontrol(mtd, NAND_CTL_SETCLE);
/*
* Write out the command to the device.
*/
this->write_byte(mtd, command);
/* Set ALE and clear CLE to start address cycle */
- this->hwcontrol(mtd, NAND_CTL_CLRCLE);
+ au1550_hwcontrol(mtd, NAND_CTL_CLRCLE);
if (column != -1 || page_addr != -1) {
- this->hwcontrol(mtd, NAND_CTL_SETALE);
+ au1550_hwcontrol(mtd, NAND_CTL_SETALE);
/* Serially input address */
if (column != -1) {
*/
ce_override = 1;
local_irq_save(flags);
- this->hwcontrol(mtd, NAND_CTL_SETNCE);
+ au1550_hwcontrol(mtd, NAND_CTL_SETNCE);
}
this->write_byte(mtd, (u8)(page_addr >> 8));
this->write_byte(mtd, (u8)((page_addr >> 16) & 0x0f));
}
/* Latch in address */
- this->hwcontrol(mtd, NAND_CTL_CLRALE);
+ au1550_hwcontrol(mtd, NAND_CTL_CLRALE);
}
/*
udelay(1);
/* Release -CE and re-enable interrupts. */
- this->hwcontrol(mtd, NAND_CTL_CLRNCE);
+ au1550_hwcontrol(mtd, NAND_CTL_CLRNCE);
local_irq_restore(flags);
return;
}
nand_width = au_readl(MEM_STCFG3) & (1 << 22);
/* Set address of hardware control function */
- this->hwcontrol = au1550_hwcontrol;
this->dev_ready = au1550_device_ready;
this->select_chip = au1550_select_chip;
this->cmdfunc = au1550_command;
* Copyright (c) 2002 Thomas Gleixner <tgxl@linutronix.de>
*
* Derived from drivers/mtd/spia.c
- * Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com)
+ * Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com)
*
* $Id: autcpu12.c,v 1.23 2005/11/07 11:14:30 gleixner Exp $
*
* MTD structure for AUTCPU12 board
*/
static struct mtd_info *autcpu12_mtd = NULL;
-
-static int autcpu12_io_base = CS89712_VIRT_BASE;
-static int autcpu12_fio_pbase = AUTCPU12_PHYS_SMC;
-static int autcpu12_fio_ctrl = AUTCPU12_SMC_SELECT_OFFSET;
-static int autcpu12_pedr = AUTCPU12_SMC_PORT_OFFSET;
static void __iomem *autcpu12_fio_base;
/*
#define NUM_PARTITIONS128K 2
/*
* hardware specific access to control-lines
-*/
-
-static void autcpu12_hwcontrol(struct mtd_info *mtd, int cmd)
+ *
+ * ALE bit 4 autcpu12_pedr
+ * CLE bit 5 autcpu12_pedr
+ * NCE bit 0 fio_ctrl
+ *
+ */
+static void autcpu12_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
{
- switch (cmd) {
+ struct nand_chip *chip = mtd->priv;
- case NAND_CTL_SETCLE: (*(volatile unsigned char *) (autcpu12_io_base + autcpu12_pedr)) |= AUTCPU12_SMC_CLE; break;
- case NAND_CTL_CLRCLE: (*(volatile unsigned char *) (autcpu12_io_base + autcpu12_pedr)) &= ~AUTCPU12_SMC_CLE; break;
+ if (ctrl & NAND_CTRL_CHANGE) {
+ void __iomem *addr
+ unsigned char bits;
- case NAND_CTL_SETALE: (*(volatile unsigned char *) (autcpu12_io_base + autcpu12_pedr)) |= AUTCPU12_SMC_ALE; break;
- case NAND_CTL_CLRALE: (*(volatile unsigned char *) (autcpu12_io_base + autcpu12_pedr)) &= ~AUTCPU12_SMC_ALE; break;
+ addr = CS89712_VIRT_BASE + AUTCPU12_SMC_PORT_OFFSET;
+ bits = (ctrl & NAND_CLE) << 4;
+ bits |= (ctrl & NAND_ALE) << 2;
+ writeb((readb(addr) & ~0x30) | bits, addr);
- case NAND_CTL_SETNCE: (*(volatile unsigned char *) (autcpu12_fio_base + autcpu12_fio_ctrl)) = 0x01; break;
- case NAND_CTL_CLRNCE: (*(volatile unsigned char *) (autcpu12_fio_base + autcpu12_fio_ctrl)) = 0x00; break;
+ addr = autcpu12_fio_base + AUTCPU12_SMC_SELECT_OFFSET;
+ writeb((readb(addr) & ~0x1) | (ctrl & NAND_NCE), addr);
}
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
}
/*
-* read device ready pin
-*/
+ * read device ready pin
+ */
int autcpu12_device_ready(struct mtd_info *mtd)
{
+ void __iomem *addr = CS89712_VIRT_BASE + AUTCPU12_SMC_PORT_OFFSET;
- return ((*(volatile unsigned char *)(autcpu12_io_base + autcpu12_pedr)) & AUTCPU12_SMC_RDY) ? 1 : 0;
-
+ return readb(addr) & AUTCPU12_SMC_RDY;
}
/*
int err = 0;
/* Allocate memory for MTD device structure and private data */
- autcpu12_mtd = kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL);
+ autcpu12_mtd = kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip),
+ GFP_KERNEL);
if (!autcpu12_mtd) {
printk("Unable to allocate AUTCPU12 NAND MTD device structure.\n");
err = -ENOMEM;
}
/* map physical adress */
- autcpu12_fio_base = ioremap(autcpu12_fio_pbase, SZ_1K);
+ autcpu12_fio_base = ioremap(AUTCPU12_PHYS_SMC, SZ_1K);
if (!autcpu12_fio_base) {
printk("Ioremap autcpu12 SmartMedia Card failed\n");
err = -EIO;
/* Set address of NAND IO lines */
this->IO_ADDR_R = autcpu12_fio_base;
this->IO_ADDR_W = autcpu12_fio_base;
- this->hwcontrol = autcpu12_hwcontrol;
+ this->cmd_ctrl = autcpu12_hwcontrol;
this->dev_ready = autcpu12_device_ready;
/* 20 us command delay time */
this->chip_delay = 20;
/* Register the partitions */
switch (autcpu12_mtd->size) {
- case SZ_16M: add_mtd_partitions(autcpu12_mtd, partition_info16k, NUM_PARTITIONS16K); break;
- case SZ_32M: add_mtd_partitions(autcpu12_mtd, partition_info32k, NUM_PARTITIONS32K); break;
- case SZ_64M: add_mtd_partitions(autcpu12_mtd, partition_info64k, NUM_PARTITIONS64K); break;
- case SZ_128M: add_mtd_partitions(autcpu12_mtd, partition_info128k, NUM_PARTITIONS128K); break;
+ case SZ_16M:
+ add_mtd_partitions(autcpu12_mtd, partition_info16k,
+ NUM_PARTITIONS16K);
+ break;
+ case SZ_32M:
+ add_mtd_partitions(autcpu12_mtd, partition_info32k,
+ NUM_PARTITIONS32K);
+ break;
+ case SZ_64M:
+ add_mtd_partitions(autcpu12_mtd, partition_info64k,
+ NUM_PARTITIONS64K);
+ break;
+ case SZ_128M:
+ add_mtd_partitions(autcpu12_mtd, partition_info128k,
+ NUM_PARTITIONS128K);
+ break;
default:
printk("Unsupported SmartMedia device\n");
err = -ENXIO;
goto out;
out_ior:
- iounmap((void *)autcpu12_fio_base);
+ iounmap(autcpu12_fio_base);
out_mtd:
kfree(autcpu12_mtd);
out:
nand_release(autcpu12_mtd);
/* unmap physical adress */
- iounmap((void *)autcpu12_fio_base);
+ iounmap(autcpu12_fio_base);
/* Free the MTD device structure */
kfree(autcpu12_mtd);
writeb(byte, this->IO_ADDR_W + 0x801);
}
-static void cs553x_hwcontrol(struct mtd_info *mtd, int cmd)
+static void cs553x_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
{
struct nand_chip *this = mtd->priv;
void __iomem *mmio_base = this->IO_ADDR_R;
- unsigned char ctl;
-
- switch (cmd) {
- case NAND_CTL_SETCLE:
- ctl = CS_NAND_CTL_CLE;
- break;
-
- case NAND_CTL_CLRCLE:
- case NAND_CTL_CLRALE:
- case NAND_CTL_SETNCE:
- ctl = 0;
- break;
-
- case NAND_CTL_SETALE:
- ctl = CS_NAND_CTL_ALE;
- break;
-
- default:
- case NAND_CTL_CLRNCE:
- ctl = CS_NAND_CTL_CE;
- break;
+ if (ctrl & NAND_CTRL_CHANGE) {
+ unsigned char ctl = (ctrl & ~NAND_CTRL_CHANGE ) ^ 0x01;
+ writeb(ctl, mmio_base + MM_NAND_CTL);
}
- writeb(ctl, mmio_base + MM_NAND_CTL);
+ if (cmd != NAND_CMD_NONE)
+ cs553x_write_byte(mtd, cmd);
}
static int cs553x_device_ready(struct mtd_info *mtd)
goto out_mtd;
}
- this->hwcontrol = cs553x_hwcontrol;
+ this->cmd_ctrl = cs553x_hwcontrol;
this->dev_ready = cs553x_device_ready;
this->read_byte = cs553x_read_byte;
this->write_byte = cs553x_write_byte;
#define DoC_is_Millennium(doc) ((doc)->ChipID == DOC_ChipID_DocMil)
#define DoC_is_2000(doc) ((doc)->ChipID == DOC_ChipID_Doc2k)
-static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd);
+static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int bitmask);
static void doc200x_select_chip(struct mtd_info *mtd, int chip);
static int debug = 0;
uint16_t ret;
doc200x_select_chip(mtd, nr);
- doc200x_hwcontrol(mtd, NAND_CTL_SETCLE);
- this->write_byte(mtd, NAND_CMD_READID);
- doc200x_hwcontrol(mtd, NAND_CTL_CLRCLE);
- doc200x_hwcontrol(mtd, NAND_CTL_SETALE);
- this->write_byte(mtd, 0);
- doc200x_hwcontrol(mtd, NAND_CTL_CLRALE);
+ doc200x_hwcontrol(mtd, NAND_CMD_READID,
+ NAND_CTRL_CLE | NAND_CTRL_CHANGE);
+ doc200x_hwcontrol(mtd, 0, NAND_CTRL_ALE | NAND_CTRL_CHANGE);
+ doc200x_hwcontrol(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
/* We cant' use dev_ready here, but at least we wait for the
* command to complete
} ident;
void __iomem *docptr = doc->virtadr;
- doc200x_hwcontrol(mtd, NAND_CTL_SETCLE);
- doc2000_write_byte(mtd, NAND_CMD_READID);
- doc200x_hwcontrol(mtd, NAND_CTL_CLRCLE);
- doc200x_hwcontrol(mtd, NAND_CTL_SETALE);
- doc2000_write_byte(mtd, 0);
- doc200x_hwcontrol(mtd, NAND_CTL_CLRALE);
+ doc200x_hwcontrol(mtd, NAND_CMD_READID,
+ NAND_CTRL_CLE | NAND_CTRL_CHANGE);
+ doc200x_hwcontrol(mtd, 0, NAND_CTRL_ALE | NAND_CTRL_CHANGE);
+ doc200x_hwcontrol(mtd, NAND_CMD_NONE,
+ NAND_NCE | NAND_CTRL_CHANGE);
udelay(50);
chip -= (floor * doc->chips_per_floor);
/* 11.4.4 -- deassert CE before changing chip */
- doc200x_hwcontrol(mtd, NAND_CTL_CLRNCE);
+ doc200x_hwcontrol(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE);
WriteDOC(floor, docptr, FloorSelect);
WriteDOC(chip, docptr, CDSNDeviceSelect);
- doc200x_hwcontrol(mtd, NAND_CTL_SETNCE);
+ doc200x_hwcontrol(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
doc->curchip = chip;
doc->curfloor = floor;
}
-static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd)
+#define CDSN_CTRL_MSK (CDSN_CTRL_CE | CDSN_CTRL_CLE | CDSN_CTRL_ALE)
+
+static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
{
struct nand_chip *this = mtd->priv;
struct doc_priv *doc = this->priv;
void __iomem *docptr = doc->virtadr;
- switch (cmd) {
- case NAND_CTL_SETNCE:
- doc->CDSNControl |= CDSN_CTRL_CE;
- break;
- case NAND_CTL_CLRNCE:
- doc->CDSNControl &= ~CDSN_CTRL_CE;
- break;
- case NAND_CTL_SETCLE:
- doc->CDSNControl |= CDSN_CTRL_CLE;
- break;
- case NAND_CTL_CLRCLE:
- doc->CDSNControl &= ~CDSN_CTRL_CLE;
- break;
- case NAND_CTL_SETALE:
- doc->CDSNControl |= CDSN_CTRL_ALE;
- break;
- case NAND_CTL_CLRALE:
- doc->CDSNControl &= ~CDSN_CTRL_ALE;
- break;
- case NAND_CTL_SETWP:
- doc->CDSNControl |= CDSN_CTRL_WP;
- break;
- case NAND_CTL_CLRWP:
- doc->CDSNControl &= ~CDSN_CTRL_WP;
- break;
+ if (ctrl & NAND_CTRL_CHANGE) {
+ doc->CDSNControl &= ~CDSN_CTRL_MSK;
+ doc->CDSNControl |= ctrl & CDSN_CTRL_MSK;
+ if (debug)
+ printk("hwcontrol(%d): %02x\n", cmd, doc->CDSNControl);
+ WriteDOC(doc->CDSNControl, docptr, CDSNControl);
+ /* 11.4.3 -- 4 NOPs after CSDNControl write */
+ DoC_Delay(doc, 4);
}
- if (debug)
- printk("hwcontrol(%d): %02x\n", cmd, doc->CDSNControl);
- WriteDOC(doc->CDSNControl, docptr, CDSNControl);
- /* 11.4.3 -- 4 NOPs after CSDNControl write */
- DoC_Delay(doc, 4);
+ if (cmd != NAND_CMD_NONE)
+ this->write_byte(mtd, cmd);
}
static void doc2001plus_command(struct mtd_info *mtd, unsigned command, int column, int page_addr)
this->read_buf = doc2001plus_readbuf;
this->verify_buf = doc2001plus_verifybuf;
this->scan_bbt = inftl_scan_bbt;
- this->hwcontrol = NULL;
+ this->cmd_ctrl = NULL;
this->select_chip = doc2001plus_select_chip;
this->cmdfunc = doc2001plus_command;
this->ecc.hwctl = doc2001plus_enable_hwecc;
nand->priv = doc;
nand->select_chip = doc200x_select_chip;
- nand->hwcontrol = doc200x_hwcontrol;
+ nand->cmd_ctrl = doc200x_hwcontrol;
nand->dev_ready = doc200x_dev_ready;
nand->waitfunc = doc200x_wait;
nand->block_bad = doc200x_block_bad;
/*
* hardware specific access to control-lines
+ *
+ * NAND_NCE: bit 0 -> bit 7
+ * NAND_CLE: bit 1 -> bit 4
+ * NAND_ALE: bit 2 -> bit 5
*/
-static void ep7312_hwcontrol(struct mtd_info *mtd, int cmd)
+static void ep7312_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
- switch (cmd) {
-
- case NAND_CTL_SETCLE:
- clps_writeb(clps_readb(ep7312_pxdr) | 0x10, ep7312_pxdr);
- break;
- case NAND_CTL_CLRCLE:
- clps_writeb(clps_readb(ep7312_pxdr) & ~0x10, ep7312_pxdr);
- break;
-
- case NAND_CTL_SETALE:
- clps_writeb(clps_readb(ep7312_pxdr) | 0x20, ep7312_pxdr);
- break;
- case NAND_CTL_CLRALE:
- clps_writeb(clps_readb(ep7312_pxdr) & ~0x20, ep7312_pxdr);
- break;
-
- case NAND_CTL_SETNCE:
- clps_writeb((clps_readb(ep7312_pxdr) | 0x80) & ~0x40, ep7312_pxdr);
- break;
- case NAND_CTL_CLRNCE:
- clps_writeb((clps_readb(ep7312_pxdr) | 0x80) | 0x40, ep7312_pxdr);
- break;
+ struct nand_chip *chip = mtd->priv;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ unsigned char bits;
+
+ bits = (ctrl & (NAND_CLE | NAND_ALE)) << 3;
+ bits = (ctrl & NAND_NCE) << 7;
+
+ clps_writeb((clps_readb(ep7312_pxdr) & 0xB0) | 0x10,
+ ep7312_pxdr);
}
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
}
/*
/* insert callbacks */
this->IO_ADDR_R = ep7312_fio_base;
this->IO_ADDR_W = ep7312_fio_base;
- this->hwcontrol = ep7312_hwcontrol;
+ this->cmd_ctrl = ep7312_hwcontrol;
this->dev_ready = ep7312_device_ready;
/* 15 us command delay time */
this->chip_delay = 15;
/*
* hardware specific access to control-lines
+ *
+ * NAND_NCE: bit 0 - don't care
+ * NAND_CLE: bit 1 - address bit 2
+ * NAND_ALE: bit 2 - address bit 3
*/
-static void h1910_hwcontrol(struct mtd_info *mtd, int cmd)
+static void h1910_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
{
- struct nand_chip *this = (struct nand_chip *)(mtd->priv);
-
- switch (cmd) {
-
- case NAND_CTL_SETCLE:
- this->IO_ADDR_R |= (1 << 2);
- this->IO_ADDR_W |= (1 << 2);
- break;
- case NAND_CTL_CLRCLE:
- this->IO_ADDR_R &= ~(1 << 2);
- this->IO_ADDR_W &= ~(1 << 2);
- break;
-
- case NAND_CTL_SETALE:
- this->IO_ADDR_R |= (1 << 3);
- this->IO_ADDR_W |= (1 << 3);
- break;
- case NAND_CTL_CLRALE:
- this->IO_ADDR_R &= ~(1 << 3);
- this->IO_ADDR_W &= ~(1 << 3);
- break;
-
- case NAND_CTL_SETNCE:
- break;
- case NAND_CTL_CLRNCE:
- break;
- }
+ struct nand_chip *chip = mtd->priv;
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W | ((ctrl & 0x6) << 1));
}
/*
/* insert callbacks */
this->IO_ADDR_R = nandaddr;
this->IO_ADDR_W = nandaddr;
- this->hwcontrol = h1910_hwcontrol;
+ this->cmd_ctrl = h1910_hwcontrol;
this->dev_ready = NULL; /* unknown whether that was correct or not so we will just do it like this */
/* 15 us command delay time */
this->chip_delay = 50;
struct nand_chip *this = mtd->priv;
switch (chip) {
case -1:
- this->hwcontrol(mtd, NAND_CTL_CLRNCE);
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE);
break;
case 0:
- this->hwcontrol(mtd, NAND_CTL_SETNCE);
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
break;
default:
* Send command to NAND device. This function is used for small page
* devices (256/512 Bytes per page)
*/
-static void nand_command(struct mtd_info *mtd, unsigned command, int column,
- int page_addr)
+static void nand_command(struct mtd_info *mtd, unsigned int command,
+ int column, int page_addr)
{
register struct nand_chip *this = mtd->priv;
+ int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE;
- /* Begin command latch cycle */
- this->hwcontrol(mtd, NAND_CTL_SETCLE);
/*
* Write out the command to the device.
*/
column -= 256;
readcmd = NAND_CMD_READ1;
}
- this->write_byte(mtd, readcmd);
+ this->cmd_ctrl(mtd, readcmd, ctrl);
+ ctrl &= ~NAND_CTRL_CHANGE;
}
- this->write_byte(mtd, command);
+ this->cmd_ctrl(mtd, command, ctrl);
- /* Set ALE and clear CLE to start address cycle */
- this->hwcontrol(mtd, NAND_CTL_CLRCLE);
-
- if (column != -1 || page_addr != -1) {
- this->hwcontrol(mtd, NAND_CTL_SETALE);
-
- /* Serially input address */
- if (column != -1) {
- /* Adjust columns for 16 bit buswidth */
- if (this->options & NAND_BUSWIDTH_16)
- column >>= 1;
- this->write_byte(mtd, column);
- }
- if (page_addr != -1) {
- this->write_byte(mtd, (uint8_t)(page_addr & 0xff));
- this->write_byte(mtd, (uint8_t)((page_addr >> 8) & 0xff));
- /* One more address cycle for devices > 32MiB */
- if (this->chipsize > (32 << 20))
- this->write_byte(mtd, (uint8_t)((page_addr >> 16) & 0x0f));
- }
- /* Latch in address */
- this->hwcontrol(mtd, NAND_CTL_CLRALE);
+ /*
+ * Address cycle, when necessary
+ */
+ ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE;
+ /* Serially input address */
+ if (column != -1) {
+ /* Adjust columns for 16 bit buswidth */
+ if (this->options & NAND_BUSWIDTH_16)
+ column >>= 1;
+ this->cmd_ctrl(mtd, column, ctrl);
+ ctrl &= ~NAND_CTRL_CHANGE;
+ }
+ if (page_addr != -1) {
+ this->cmd_ctrl(mtd, page_addr, ctrl);
+ ctrl &= ~NAND_CTRL_CHANGE;
+ this->cmd_ctrl(mtd, page_addr >> 8, ctrl);
+ /* One more address cycle for devices > 32MiB */
+ if (this->chipsize > (32 << 20))
+ this->cmd_ctrl(mtd, page_addr >> 16, ctrl);
}
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
/*
* program and erase have their own busy handlers
case NAND_CMD_ERASE2:
case NAND_CMD_SEQIN:
case NAND_CMD_STATUS:
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE);
return;
case NAND_CMD_RESET:
if (this->dev_ready)
break;
udelay(this->chip_delay);
- this->hwcontrol(mtd, NAND_CTL_SETCLE);
- this->write_byte(mtd, NAND_CMD_STATUS);
- this->hwcontrol(mtd, NAND_CTL_CLRCLE);
+ this->cmd_ctrl(mtd, NAND_CMD_STATUS,
+ NAND_CTRL_CLE | NAND_CTRL_CHANGE);
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE);
while (!(this->read_byte(mtd) & NAND_STATUS_READY)) ;
return;
* @column: the column address for this command, -1 if none
* @page_addr: the page address for this command, -1 if none
*
- * Send command to NAND device. This is the version for the new large page devices
- * We dont have the separate regions as we have in the small page devices.
- * We must emulate NAND_CMD_READOOB to keep the code compatible.
+ * Send command to NAND device. This is the version for the new large page
+ * devices We dont have the separate regions as we have in the small page
+ * devices. We must emulate NAND_CMD_READOOB to keep the code compatible.
*
*/
-static void nand_command_lp(struct mtd_info *mtd, unsigned command, int column, int page_addr)
+static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
+ int column, int page_addr)
{
register struct nand_chip *this = mtd->priv;
command = NAND_CMD_READ0;
}
- /* Begin command latch cycle */
- this->hwcontrol(mtd, NAND_CTL_SETCLE);
- /* Write out the command to the device. */
- this->write_byte(mtd, (command & 0xff));
- /* End command latch cycle */
- this->hwcontrol(mtd, NAND_CTL_CLRCLE);
+ /* Command latch cycle */
+ this->cmd_ctrl(mtd, command & 0xff,
+ NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
if (column != -1 || page_addr != -1) {
- this->hwcontrol(mtd, NAND_CTL_SETALE);
+ int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE;
/* Serially input address */
if (column != -1) {
/* Adjust columns for 16 bit buswidth */
if (this->options & NAND_BUSWIDTH_16)
column >>= 1;
- this->write_byte(mtd, column & 0xff);
- this->write_byte(mtd, column >> 8);
+ this->cmd_ctrl(mtd, column, ctrl);
+ ctrl &= ~NAND_CTRL_CHANGE;
+ this->cmd_ctrl(mtd, column >> 8, ctrl);
}
if (page_addr != -1) {
- this->write_byte(mtd, (uint8_t)(page_addr & 0xff));
- this->write_byte(mtd, (uint8_t)((page_addr >> 8) & 0xff));
+ this->cmd_ctrl(mtd, page_addr, ctrl);
+ this->cmd_ctrl(mtd, page_addr >> 8,
+ NAND_NCE | NAND_ALE);
/* One more address cycle for devices > 128MiB */
if (this->chipsize > (128 << 20))
- this->write_byte(mtd, (uint8_t)((page_addr >> 16) & 0xff));
+ this->cmd_ctrl(mtd, page_addr >> 16,
+ NAND_NCE | NAND_ALE);
}
- /* Latch in address */
- this->hwcontrol(mtd, NAND_CTL_CLRALE);
}
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
/*
* program and erase have their own busy handlers
if (this->dev_ready)
break;
udelay(this->chip_delay);
- this->hwcontrol(mtd, NAND_CTL_SETCLE);
- this->write_byte(mtd, NAND_CMD_STATUS);
- this->hwcontrol(mtd, NAND_CTL_CLRCLE);
+ this->cmd_ctrl(mtd, NAND_CMD_STATUS, NAND_NCE | NAND_CLE);
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE);
while (!(this->read_byte(mtd) & NAND_STATUS_READY)) ;
return;
case NAND_CMD_READ0:
- /* Begin command latch cycle */
- this->hwcontrol(mtd, NAND_CTL_SETCLE);
- /* Write out the start read command */
- this->write_byte(mtd, NAND_CMD_READSTART);
- /* End command latch cycle */
- this->hwcontrol(mtd, NAND_CTL_CLRCLE);
- /* Fall through into ready check */
+ this->cmd_ctrl(mtd, NAND_CMD_READSTART, NAND_NCE | NAND_CLE);
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE);
/* This applies to read commands */
default:
}
}
-static void
-ns_hwcontrol(struct mtd_info *mtd, int cmd)
-{
- struct nandsim *ns = (struct nandsim *)((struct nand_chip *)mtd->priv)->priv;
-
- switch (cmd) {
-
- /* set CLE line high */
- case NAND_CTL_SETCLE:
- NS_DBG("ns_hwcontrol: start command latch cycles\n");
- ns->lines.cle = 1;
- break;
-
- /* set CLE line low */
- case NAND_CTL_CLRCLE:
- NS_DBG("ns_hwcontrol: stop command latch cycles\n");
- ns->lines.cle = 0;
- break;
-
- /* set ALE line high */
- case NAND_CTL_SETALE:
- NS_DBG("ns_hwcontrol: start address latch cycles\n");
- ns->lines.ale = 1;
- break;
-
- /* set ALE line low */
- case NAND_CTL_CLRALE:
- NS_DBG("ns_hwcontrol: stop address latch cycles\n");
- ns->lines.ale = 0;
- break;
-
- /* set WP line high */
- case NAND_CTL_SETWP:
- NS_DBG("ns_hwcontrol: enable write protection\n");
- ns->lines.wp = 1;
- break;
-
- /* set WP line low */
- case NAND_CTL_CLRWP:
- NS_DBG("ns_hwcontrol: disable write protection\n");
- ns->lines.wp = 0;
- break;
-
- /* set CE line low */
- case NAND_CTL_SETNCE:
- NS_DBG("ns_hwcontrol: enable chip\n");
- ns->lines.ce = 1;
- break;
-
- /* set CE line high */
- case NAND_CTL_CLRNCE:
- NS_DBG("ns_hwcontrol: disable chip\n");
- ns->lines.ce = 0;
- break;
-
- default:
- NS_ERR("hwcontrol: unknown command\n");
- }
-
- return;
-}
-
static u_char
ns_nand_read_byte(struct mtd_info *mtd)
{
return;
}
+static void ns_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int bitmask)
+{
+ struct nandsim *ns = ((struct nand_chip *)mtd->priv)->priv;
+
+ ns->lines.cle = bitmask & NAND_CLE ? 1 : 0;
+ ns->lines.ale = bitmask & NAND_ALE ? 1 : 0;
+ ns->lines.ce = bitmask & NAND_NCE ? 1 : 0;
+
+ if (cmd != NAND_CMD_NONE)
+ ns_nand_write_byte(mtd, cmd);
+}
+
static int
ns_device_ready(struct mtd_info *mtd)
{
/*
* Register simulator's callbacks.
*/
- chip->hwcontrol = ns_hwcontrol;
+ chip->cmd_ctrl = ns_hwcontrol;
chip->read_byte = ns_nand_read_byte;
chip->dev_ready = ns_device_ready;
chip->write_byte = ns_nand_write_byte;
writel(ccr, ndfc->ndfcbase + NDFC_CCR);
}
-static void ndfc_hwcontrol(struct mtd_info *mtd, int cmd)
+static void ndfc_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
- struct ndfc_controller *ndfc = &ndfc_ctrl;
struct nand_chip *chip = mtd->priv;
- switch (cmd) {
- case NAND_CTL_SETCLE:
- chip->IO_ADDR_W = ndfc->ndfcbase + NDFC_CMD;
- break;
- case NAND_CTL_SETALE:
- chip->IO_ADDR_W = ndfc->ndfcbase + NDFC_ALE;
- break;
- default:
- chip->IO_ADDR_W = ndfc->ndfcbase + NDFC_DATA;
- break;
- }
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ if (ctrl & NAND_CLE)
+ writel(cmd & 0xFF, chip->IO_ADDR_W + NDFC_CMD);
+ else
+ writel(cmd & 0xFF, chip->IO_ADDR_W + NDFC_ALE);
}
static int ndfc_ready(struct mtd_info *mtd)
chip->IO_ADDR_R = ndfc->ndfcbase + NDFC_DATA;
chip->IO_ADDR_W = ndfc->ndfcbase + NDFC_DATA;
- chip->hwcontrol = ndfc_hwcontrol;
+ chip->cmd_ctrl = ndfc_hwcontrol;
chip->dev_ready = ndfc_ready;
chip->select_chip = ndfc_select_chip;
chip->chip_delay = 50;
/*
* hardware specific access to control-lines
*/
-static void ppchameleon_hwcontrol(struct mtd_info *mtdinfo, int cmd)
+static void ppchameleon_hwcontrol(struct mtd_info *mtdinfo, int cmd,
+ unsigned int ctrl)
{
- switch (cmd) {
-
- case NAND_CTL_SETCLE:
- MACRO_NAND_CTL_SETCLE((unsigned long)CFG_NAND0_PADDR);
- break;
- case NAND_CTL_CLRCLE:
- MACRO_NAND_CTL_CLRCLE((unsigned long)CFG_NAND0_PADDR);
- break;
- case NAND_CTL_SETALE:
- MACRO_NAND_CTL_SETALE((unsigned long)CFG_NAND0_PADDR);
- break;
- case NAND_CTL_CLRALE:
- MACRO_NAND_CTL_CLRALE((unsigned long)CFG_NAND0_PADDR);
- break;
- case NAND_CTL_SETNCE:
- MACRO_NAND_ENABLE_CE((unsigned long)CFG_NAND0_PADDR);
- break;
- case NAND_CTL_CLRNCE:
- MACRO_NAND_DISABLE_CE((unsigned long)CFG_NAND0_PADDR);
- break;
+ struct nand_chip *chip = mtd->priv;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+#error Missing headerfiles. No way to fix this. -tglx
+ switch (cmd) {
+ case NAND_CTL_SETCLE:
+ MACRO_NAND_CTL_SETCLE((unsigned long)CFG_NAND0_PADDR);
+ break;
+ case NAND_CTL_CLRCLE:
+ MACRO_NAND_CTL_CLRCLE((unsigned long)CFG_NAND0_PADDR);
+ break;
+ case NAND_CTL_SETALE:
+ MACRO_NAND_CTL_SETALE((unsigned long)CFG_NAND0_PADDR);
+ break;
+ case NAND_CTL_CLRALE:
+ MACRO_NAND_CTL_CLRALE((unsigned long)CFG_NAND0_PADDR);
+ break;
+ case NAND_CTL_SETNCE:
+ MACRO_NAND_ENABLE_CE((unsigned long)CFG_NAND0_PADDR);
+ break;
+ case NAND_CTL_CLRNCE:
+ MACRO_NAND_DISABLE_CE((unsigned long)CFG_NAND0_PADDR);
+ break;
+ }
}
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
}
-static void ppchameleonevb_hwcontrol(struct mtd_info *mtdinfo, int cmd)
+static void ppchameleonevb_hwcontrol(struct mtd_info *mtdinfo, int cmd,
+ unsigned int ctrl)
{
- switch (cmd) {
-
- case NAND_CTL_SETCLE:
- MACRO_NAND_CTL_SETCLE((unsigned long)CFG_NAND1_PADDR);
- break;
- case NAND_CTL_CLRCLE:
- MACRO_NAND_CTL_CLRCLE((unsigned long)CFG_NAND1_PADDR);
- break;
- case NAND_CTL_SETALE:
- MACRO_NAND_CTL_SETALE((unsigned long)CFG_NAND1_PADDR);
- break;
- case NAND_CTL_CLRALE:
- MACRO_NAND_CTL_CLRALE((unsigned long)CFG_NAND1_PADDR);
- break;
- case NAND_CTL_SETNCE:
- MACRO_NAND_ENABLE_CE((unsigned long)CFG_NAND1_PADDR);
- break;
- case NAND_CTL_CLRNCE:
- MACRO_NAND_DISABLE_CE((unsigned long)CFG_NAND1_PADDR);
- break;
+ struct nand_chip *chip = mtd->priv;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+#error Missing headerfiles. No way to fix this. -tglx
+ switch (cmd) {
+ case NAND_CTL_SETCLE:
+ MACRO_NAND_CTL_SETCLE((unsigned long)CFG_NAND1_PADDR);
+ break;
+ case NAND_CTL_CLRCLE:
+ MACRO_NAND_CTL_CLRCLE((unsigned long)CFG_NAND1_PADDR);
+ break;
+ case NAND_CTL_SETALE:
+ MACRO_NAND_CTL_SETALE((unsigned long)CFG_NAND1_PADDR);
+ break;
+ case NAND_CTL_CLRALE:
+ MACRO_NAND_CTL_CLRALE((unsigned long)CFG_NAND1_PADDR);
+ break;
+ case NAND_CTL_SETNCE:
+ MACRO_NAND_ENABLE_CE((unsigned long)CFG_NAND1_PADDR);
+ break;
+ case NAND_CTL_CLRNCE:
+ MACRO_NAND_DISABLE_CE((unsigned long)CFG_NAND1_PADDR);
+ break;
+ }
}
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
}
#ifdef USE_READY_BUSY_PIN
/* insert callbacks */
this->IO_ADDR_R = ppchameleon_fio_base;
this->IO_ADDR_W = ppchameleon_fio_base;
- this->hwcontrol = ppchameleon_hwcontrol;
+ this->cmd_ctrl = ppchameleon_hwcontrol;
#ifdef USE_READY_BUSY_PIN
this->dev_ready = ppchameleon_device_ready;
#endif
/* insert callbacks */
this->IO_ADDR_R = ppchameleonevb_fio_base;
this->IO_ADDR_W = ppchameleonevb_fio_base;
- this->hwcontrol = ppchameleonevb_hwcontrol;
+ this->cmd_ctrl = ppchameleonevb_hwcontrol;
#ifdef USE_READY_BUSY_PIN
this->dev_ready = ppchameleonevb_device_ready;
#endif
* Address lines (A24-A22), so no action is required here.
*
*/
-static void rtc_from4_hwcontrol(struct mtd_info *mtd, int cmd)
+static void rtc_from4_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
{
- struct nand_chip *this = (struct nand_chip *)(mtd->priv);
+ struct nand_chip *chip = (mtd->priv);
- switch (cmd) {
+ if (cmd == NAND_CMD_NONE)
+ return;
- case NAND_CTL_SETCLE:
- this->IO_ADDR_W = (void __iomem *)((unsigned long)this->IO_ADDR_W | RTC_FROM4_CLE);
- break;
- case NAND_CTL_CLRCLE:
- this->IO_ADDR_W = (void __iomem *)((unsigned long)this->IO_ADDR_W & ~RTC_FROM4_CLE);
- break;
-
- case NAND_CTL_SETALE:
- this->IO_ADDR_W = (void __iomem *)((unsigned long)this->IO_ADDR_W | RTC_FROM4_ALE);
- break;
- case NAND_CTL_CLRALE:
- this->IO_ADDR_W = (void __iomem *)((unsigned long)this->IO_ADDR_W & ~RTC_FROM4_ALE);
- break;
-
- case NAND_CTL_SETNCE:
- break;
- case NAND_CTL_CLRNCE:
- break;
-
- }
+ if (ctrl & NAND_CLE)
+ writeb(cmd, chip->IO_ADDR_W | RTC_FROM4_CLE);
+ else
+ writeb(cmd, chip->IO_ADDR_W | RTC_FROM4_ALE);
}
/*
this->IO_ADDR_R = rtc_from4_fio_base;
this->IO_ADDR_W = rtc_from4_fio_base;
/* Set address of hardware control function */
- this->hwcontrol = rtc_from4_hwcontrol;
+ this->cmd_ctrl = rtc_from4_hwcontrol;
/* Set address of chip select function */
this->select_chip = rtc_from4_nand_select_chip;
/* command delay time (in us) */
*
*/
-static void s3c2410_nand_hwcontrol(struct mtd_info *mtd, int cmd)
+static void s3c2410_nand_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigend int ctrl)
{
struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd);
struct nand_chip *chip = mtd->priv;
- switch (cmd) {
- case NAND_CTL_SETNCE:
- case NAND_CTL_CLRNCE:
- printk(KERN_ERR "%s: called for NCE\n", __FUNCTION__);
- break;
-
- case NAND_CTL_SETCLE:
- chip->IO_ADDR_W = info->regs + S3C2410_NFCMD;
- break;
-
- case NAND_CTL_SETALE:
- chip->IO_ADDR_W = info->regs + S3C2410_NFADDR;
- break;
-
- /* NAND_CTL_CLRCLE: */
- /* NAND_CTL_CLRALE: */
- default:
- chip->IO_ADDR_W = info->regs + S3C2410_NFDATA;
- break;
- }
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ if (cmd & NAND_CLE)
+ writeb(cmd, info->regs + S3C2410_NFCMD);
+ else
+ writeb(cmd, info->regs + S3C2410_NFADDR);
}
/* command and control functions */
-static void s3c2440_nand_hwcontrol(struct mtd_info *mtd, int cmd)
+static void s3c2410_nand_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigend int ctrl)
{
struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd);
struct nand_chip *chip = mtd->priv;
- switch (cmd) {
- case NAND_CTL_SETNCE:
- case NAND_CTL_CLRNCE:
- printk(KERN_ERR "%s: called for NCE\n", __FUNCTION__);
- break;
-
- case NAND_CTL_SETCLE:
- chip->IO_ADDR_W = info->regs + S3C2440_NFCMD;
- break;
-
- case NAND_CTL_SETALE:
- chip->IO_ADDR_W = info->regs + S3C2440_NFADDR;
- break;
-
- /* NAND_CTL_CLRCLE: */
- /* NAND_CTL_CLRALE: */
- default:
- chip->IO_ADDR_W = info->regs + S3C2440_NFDATA;
- break;
- }
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ if (cmd & NAND_CLE)
+ writeb(cmd, info->regs + S3C2440_NFCMD);
+ else
+ writeb(cmd, info->regs + S3C2440_NFADDR);
}
/* s3c2410_nand_devready()
chip->IO_ADDR_R = info->regs + S3C2410_NFDATA;
chip->IO_ADDR_W = info->regs + S3C2410_NFDATA;
- chip->hwcontrol = s3c2410_nand_hwcontrol;
+ chip->cmd_ctrl = s3c2410_nand_hwcontrol;
chip->dev_ready = s3c2410_nand_devready;
chip->write_buf = s3c2410_nand_write_buf;
chip->read_buf = s3c2410_nand_read_buf;
if (info->is_s3c2440) {
chip->IO_ADDR_R = info->regs + S3C2440_NFDATA;
chip->IO_ADDR_W = info->regs + S3C2440_NFDATA;
- chip->hwcontrol = s3c2440_nand_hwcontrol;
+ chip->cmd_ctrl = s3c2440_nand_hwcontrol;
}
nmtd->info = info;
/*
* hardware specific access to control-lines
+ * ctrl:
+ * NAND_CNE: bit 0 -> bit 0 & 4
+ * NAND_CLE: bit 1 -> bit 1
+ * NAND_ALE: bit 2 -> bit 2
+ *
*/
-static void sharpsl_nand_hwcontrol(struct mtd_info *mtd, int cmd)
+static void sharpsl_nand_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
{
- switch (cmd) {
- case NAND_CTL_SETCLE:
- writeb(readb(FLASHCTL) | FLCLE, FLASHCTL);
- break;
- case NAND_CTL_CLRCLE:
- writeb(readb(FLASHCTL) & ~FLCLE, FLASHCTL);
- break;
-
- case NAND_CTL_SETALE:
- writeb(readb(FLASHCTL) | FLALE, FLASHCTL);
- break;
- case NAND_CTL_CLRALE:
- writeb(readb(FLASHCTL) & ~FLALE, FLASHCTL);
- break;
-
- case NAND_CTL_SETNCE:
- writeb(readb(FLASHCTL) & ~(FLCE0 | FLCE1), FLASHCTL);
- break;
- case NAND_CTL_CLRNCE:
- writeb(readb(FLASHCTL) | (FLCE0 | FLCE1), FLASHCTL);
- break;
+ struct nand_chip *chip = mtd->priv;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ unsigned char bits = ctrl & 0x07;
+
+ bits |= (ctrl & 0x01) << 4;
+ writeb((readb(FLASHCTL) & 0x17) | bits, FLASHCTL);
}
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
}
static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
this->IO_ADDR_R = FLASHIO;
this->IO_ADDR_W = FLASHIO;
/* Set address of hardware control function */
- this->hwcontrol = sharpsl_nand_hwcontrol;
+ this->cmd_ctrl = sharpsl_nand_hwcontrol;
this->dev_ready = sharpsl_nand_dev_ready;
/* 15 us command delay time */
this->chip_delay = 15;
/*
* hardware specific access to control-lines
-*/
+ *
+ * ctrl:
+ * NAND_CNE: bit 0 -> bit 2
+ * NAND_CLE: bit 1 -> bit 0
+ * NAND_ALE: bit 2 -> bit 1
+ */
static void spia_hwcontrol(struct mtd_info *mtd, int cmd)
{
- switch (cmd) {
+ struct nand_chip *chip = mtd->priv;
- case NAND_CTL_SETCLE: (*(volatile unsigned char *) (spia_io_base + spia_pedr)) |= 0x01; break;
- case NAND_CTL_CLRCLE: (*(volatile unsigned char *) (spia_io_base + spia_pedr)) &= ~0x01; break;
+ if (ctrl & NAND_CTRL_CHANGE) {
+ void __iomem *addr = spia_io_base + spia_pedr;
+ unsigned char bits;
- case NAND_CTL_SETALE: (*(volatile unsigned char *) (spia_io_base + spia_pedr)) |= 0x02; break;
- case NAND_CTL_CLRALE: (*(volatile unsigned char *) (spia_io_base + spia_pedr)) &= ~0x02; break;
-
- case NAND_CTL_SETNCE: (*(volatile unsigned char *) (spia_io_base + spia_pedr)) &= ~0x04; break;
- case NAND_CTL_CLRNCE: (*(volatile unsigned char *) (spia_io_base + spia_pedr)) |= 0x04; break;
+ bits = (ctrl & NAND_CNE) << 2;
+ bits |= (ctrl & NAND_CLE | NAND_ALE) >> 1;
+ writeb((readb(addr) & ~0x7) | bits, addr);
}
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
}
/*
this->IO_ADDR_R = (void __iomem *)spia_fio_base;
this->IO_ADDR_W = (void __iomem *)spia_fio_base;
/* Set address of hardware control function */
- this->hwcontrol = spia_hwcontrol;
+ this->cmd_ctrl = spia_hwcontrol;
/* 15 us command delay time */
this->chip_delay = 15;
#include <asm/arch-omap1510/hardware.h>
#include <asm/arch/gpio.h>
+#define CONFIG_NAND_WORKAROUND 1
+
/*
* MTD structure for TOTO board
*/
static unsigned long toto_io_base = OMAP_FLASH_1_BASE;
-#define CONFIG_NAND_WORKAROUND 1
-
-#define NAND_NCE 0x4000
-#define NAND_CLE 0x1000
-#define NAND_ALE 0x0002
-#define NAND_MASK (NAND_CLE | NAND_ALE | NAND_NCE)
-
-#define T_NAND_CTL_CLRALE(iob) gpiosetout(NAND_ALE, 0)
-#define T_NAND_CTL_SETALE(iob) gpiosetout(NAND_ALE, NAND_ALE)
-#ifdef CONFIG_NAND_WORKAROUND /* "some" dev boards busted, blue wired to rts2 :( */
-#define T_NAND_CTL_CLRCLE(iob) gpiosetout(NAND_CLE, 0); rts2setout(2, 2)
-#define T_NAND_CTL_SETCLE(iob) gpiosetout(NAND_CLE, NAND_CLE); rts2setout(2, 0)
-#else
-#define T_NAND_CTL_CLRCLE(iob) gpiosetout(NAND_CLE, 0)
-#define T_NAND_CTL_SETCLE(iob) gpiosetout(NAND_CLE, NAND_CLE)
-#endif
-#define T_NAND_CTL_SETNCE(iob) gpiosetout(NAND_NCE, 0)
-#define T_NAND_CTL_CLRNCE(iob) gpiosetout(NAND_NCE, NAND_NCE)
-
/*
* Define partitions for flash devices
*/
#define NUM_PARTITIONS32M 3
#define NUM_PARTITIONS64M 4
+
/*
* hardware specific access to control-lines
-*/
-
-static void toto_hwcontrol(struct mtd_info *mtd, int cmd)
+ *
+ * ctrl:
+ * NAND_NCE: bit 0 -> bit 14 (0x4000)
+ * NAND_CLE: bit 1 -> bit 12 (0x1000)
+ * NAND_ALE: bit 2 -> bit 1 (0x0002)
+ */
+static void toto_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
{
+ struct nand_chip *chip = mtd->priv;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ unsigned long bits;
- udelay(1); /* hopefully enough time for tc make proceding write to clear */
- switch (cmd) {
- case NAND_CTL_SETCLE: T_NAND_CTL_SETCLE(cmd); break;
- case NAND_CTL_CLRCLE: T_NAND_CTL_CLRCLE(cmd); break;
+ /* hopefully enough time for tc make proceding write to clear */
+ udelay(1);
- case NAND_CTL_SETALE: T_NAND_CTL_SETALE(cmd); break;
- case NAND_CTL_CLRALE: T_NAND_CTL_CLRALE(cmd); break;
+ bits = (~ctrl & NAND_NCE) << 14;
+ bits |= (ctrl & NAND_CLE) << 12;
+ bits |= (ctrl & NAND_ALE) >> 1;
- case NAND_CTL_SETNCE: T_NAND_CTL_SETNCE(cmd); break;
- case NAND_CTL_CLRNCE: T_NAND_CTL_CLRNCE(cmd); break;
+#warning Wild guess as gpiosetout() is nowhere defined in the kernel source - tglx
+ gpiosetout(0x5002, bits);
+
+#ifdef CONFIG_NAND_WORKAROUND
+ /* "some" dev boards busted, blue wired to rts2 :( */
+ rts2setout(2, (ctrl & NAND_CLE) << 1);
+#endif
+ /* allow time to ensure gpio state to over take memory write */
+ udelay(1);
}
- udelay(1); /* allow time to ensure gpio state to over take memory write */
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
}
/*
/* Set address of NAND IO lines */
this->IO_ADDR_R = toto_io_base;
this->IO_ADDR_W = toto_io_base;
- this->hwcontrol = toto_hwcontrol;
+ this->cmd_ctrl = toto_hwcontrol;
this->dev_ready = NULL;
/* 25 us command delay time */
this->chip_delay = 30;
/*
* hardware specific access to control-lines
+ *
+ * ctrl:
+ * NAND_NCE: bit 0 -> bit 2
+ * NAND_CLE: bit 1 -> bit 1
+ * NAND_ALE: bit 2 -> bit 0
*/
-static void ts7250_hwcontrol(struct mtd_info *mtd, int cmd)
+static void ts7250_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
- unsigned long ctrl = TS72XX_NAND_CONTROL_VIRT_BASE;
-
- switch (cmd) {
- case NAND_CTL_SETCLE:
- __raw_writeb(__raw_readb(ctrl) | 0x2, ctrl);
- break;
- case NAND_CTL_CLRCLE:
- __raw_writeb(__raw_readb(ctrl) & ~0x2, ctrl);
- break;
- case NAND_CTL_SETALE:
- __raw_writeb(__raw_readb(ctrl) | 0x1, ctrl);
- break;
- case NAND_CTL_CLRALE:
- __raw_writeb(__raw_readb(ctrl) & ~0x1, ctrl);
- break;
- case NAND_CTL_SETNCE:
- __raw_writeb(__raw_readb(ctrl) | 0x4, ctrl);
- break;
- case NAND_CTL_CLRNCE:
- __raw_writeb(__raw_readb(ctrl) & ~0x4, ctrl);
- break;
+ struct nand_chip *chip = mtd->priv;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ unsigned long addr = TS72XX_NAND_CONTROL_VIRT_BASE;
+ unsigned char bits;
+
+ bits = (ctrl & NAND_CNE) << 2;
+ bits |= ctrl & NAND_CLE;
+ bits |= (ctrl & NAND_ALE) >> 2;
+
+ __raw_writeb((__raw_readb(addr) & ~0x7) | bits, addr);
}
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
}
/*
/* insert callbacks */
this->IO_ADDR_R = (void *)TS72XX_NAND_DATA_VIRT_BASE;
this->IO_ADDR_W = (void *)TS72XX_NAND_DATA_VIRT_BASE;
- this->hwcontrol = ts7250_hwcontrol;
+ this->cmd_ctrl = ts7250_hwcontrol;
this->dev_ready = ts7250_device_ready;
this->chip_delay = 15;
this->ecc.mode = NAND_ECC_SOFT;
/*
* Constants for hardware specific CLE/ALE/NCE function
-*/
+ *
+ * These are bits which can be or'ed to set/clear multiple
+ * bits in one go.
+ */
/* Select the chip by setting nCE to low */
-#define NAND_CTL_SETNCE 1
-/* Deselect the chip by setting nCE to high */
-#define NAND_CTL_CLRNCE 2
+#define NAND_NCE 0x01
/* Select the command latch by setting CLE to high */
-#define NAND_CTL_SETCLE 3
-/* Deselect the command latch by setting CLE to low */
-#define NAND_CTL_CLRCLE 4
+#define NAND_CLE 0x02
/* Select the address latch by setting ALE to high */
-#define NAND_CTL_SETALE 5
-/* Deselect the address latch by setting ALE to low */
-#define NAND_CTL_CLRALE 6
-/* Set write protection by setting WP to high. Not used! */
-#define NAND_CTL_SETWP 7
-/* Clear write protection by setting WP to low. Not used! */
-#define NAND_CTL_CLRWP 8
+#define NAND_ALE 0x04
+
+#define NAND_CTRL_CLE (NAND_NCE | NAND_CLE)
+#define NAND_CTRL_ALE (NAND_NCE | NAND_ALE)
+#define NAND_CTRL_CHANGE 0x80
/*
* Standard NAND flash commands
#define NAND_CMD_STATUS_RESET 0x7f
#define NAND_CMD_STATUS_CLEAR 0xff
+#define NAND_CMD_NONE -1
+
/* Status bits */
#define NAND_STATUS_FAIL 0x01
#define NAND_STATUS_FAIL_N1 0x02
* @select_chip: [REPLACEABLE] select chip nr
* @block_bad: [REPLACEABLE] check, if the block is bad
* @block_markbad: [REPLACEABLE] mark the block bad
- * @hwcontrol: [BOARDSPECIFIC] hardwarespecific function for accesing control-lines
+ * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific funtion for controlling
+ * ALE/CLE/nCE. Also used to write command and address
* @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line
* If set to NULL no access to ready/busy is available and the ready/busy information
* is read from the chip status register
void (*select_chip)(struct mtd_info *mtd, int chip);
int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip);
int (*block_markbad)(struct mtd_info *mtd, loff_t ofs);
- void (*hwcontrol)(struct mtd_info *mtd, int cmd);
+ void (*cmd_ctrl)(struct mtd_info *mtd, int dat,
+ unsigned int ctrl);
int (*dev_ready)(struct mtd_info *mtd);
void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr);
int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this, int state);
projects / kernel / kernel-generic.git / commitdiff