@end cartouche
@noindent
The result of this attribute is a string that identifies
-the object or component that denotes a given task. If a variable Var has a task
-type, the image for this task will have the form Var_XXXXXXXX, where the
-suffix
+the object or component that denotes a given task. If a variable @code{Var}
+has a task type, the image for this task will have the form @code{Var_@var{XXXXXXXX}},
+where the suffix
is the hexadecimal representation of the virtual address of the corresponding
task control block. If the variable is an array of tasks, the image of each
task will have the form of an indexed component indicating the position of a
-given task in the array, e.g.@: Group(5)_XXXXXXX. If the task is a
+given task in the array, e.g.@: @code{Group(5)_@var{XXXXXXX}}. If the task is a
component of a record, the image of the task will have the form of a selected
component. These rules are fully recursive, so that the image of a task that
is a subcomponent of a composite object corresponds to the expression that
@end smallexample
@noindent
-where the xxx bits correspond to the left-padded bits of the
+where the @var{xxx} bits correspond to the left-padded bits of the
16-bit character value. Note that all lower half ASCII characters
are represented as ASCII bytes and all upper half characters and
other wide characters are represented as sequences of upper-half
@end smallexample
@noindent
-where the xxx bits correspond to the left-padded bits of the
+where the @var{xxx} bits correspond to the left-padded bits of the
21-bit character value. Note that all lower half ASCII characters
are represented as ASCII bytes and all upper half characters and
other wide characters are represented as sequences of upper-half
@iftex
@leftskip=.7cm
@end iftex
-16#0000#-16#007f#: 2#0xxxxxxx#
-16#0080#-16#07ff#: 2#110xxxxx# 2#10xxxxxx#
-16#0800#-16#ffff#: 2#1110xxxx# 2#10xxxxxx# 2#10xxxxxx#
+16#0000#-16#007f#: 2#0@var{xxxxxxx}#
+16#0080#-16#07ff#: 2#110@var{xxxxx}# 2#10@var{xxxxxx}#
+16#0800#-16#ffff#: 2#1110@var{xxxx}# 2#10@var{xxxxxx}# 2#10@var{xxxxxx}#
@end smallexample
@noindent
-where the xxx bits correspond to the left-padded bits of the
+where the @var{xxx} bits correspond to the left-padded bits of the
16-bit character value. Note that all lower half ASCII characters
are represented as ASCII bytes and all upper half characters and
other wide characters are represented as sequences of upper-half
@cindex @option{^-l^/ORDER_OF_ELABORATION^} (@command{gnatbind})
Output chosen elaboration order.
-@item ^-Lxxx^/BUILD_LIBRARY=xxx^
+@item ^-L@var{xxx}^/BUILD_LIBRARY=@var{xxx}^
@cindex @option{^-L^/BUILD_LIBRARY^} (@command{gnatbind})
Bind the units for library building. In this case the adainit and
adafinal procedures (@pxref{Binding with Non-Ada Main Programs})
-are renamed to ^xxxinit^XXXINIT^ and
-^xxxfinal^XXXFINAL^.
+are renamed to ^@var{xxx}init^@var{XXX}INIT^ and
+^@var{xxx}final^@var{XXX}FINAL^.
Implies ^-n^/NOCOMPILE^.
@ifclear vms
(@xref{GNAT and Libraries}, for more details.)
@item ``@option{^in^INVALID^}'' requesting an invalid value where possible
@item ``@option{^lo^LOW^}'' for the lowest possible value
@item ``@option{^hi^HIGH^}'' for the highest possible value
-@item ``@option{xx}'' for a value consisting of repeated bytes with the
-value 16#xx# (i.e., xx is a string of two hexadecimal digits).
+@item ``@option{@var{xx}}'' for a value consisting of repeated bytes with the
+value @code{16#@var{xx}#} (i.e., @var{xx} is a string of two hexadecimal digits).
@end itemize
In addition, you can specify @option{-Sev} to indicate that the value is
to be set at run time. In this case, the program will look for an environment
@cindex GNAT_INIT_SCALARS
-variable of the form @env{GNAT_INIT_SCALARS=xx}, where xx is one
-of @option{in/lo/hi/xx} with the same meanings as above.
+variable of the form @env{GNAT_INIT_SCALARS=@var{xx}}, where @var{xx} is one
+of @option{in/lo/hi/@var{xx}} with the same meanings as above.
If no environment variable is found, or if it does not have a valid value,
then the default is @option{in} (invalid values).
previous section for a full description of this mode.
@ifclear vms
-@item -gnatxxx
-This passes the given @option{-gnatxxx} switch to @code{gnat} which is
-used to parse the given file. Not all @code{xxx} options make sense,
+@item -gnat@var{xxx}
+This passes the given @option{-gnat@var{xxx}} switch to @code{gnat} which is
+used to parse the given file. Not all @var{xxx} options make sense,
but for example, the use of @option{-gnati2} allows @code{gnatchop} to
process a source file that uses Latin-2 coding for identifiers.
@end ifclear
units to be skipped.
@ifclear vms
-@item --GCC=xxxx
+@item --GCC=@var{xxxx}
@cindex @option{--GCC=} (@code{gnatchop})
Specify the path of the GNAT parser to be used. When this switch is used,
no attempt is made to add the prefix to the GNAT parser executable.
@end smallexample
@noindent
-Please note that the library must have a name of the form @file{libxxx.a} or
-@file{libxxx.so} (or @file{libxxx.dll} on Windows) in order to be accessed by
-the directive @option{-lxxx} at link time.
+Please note that the library must have a name of the form @file{lib@var{xxx}.a}
+or @file{lib@var{xxx}.so} (or @file{lib@var{xxx}.dll} on Windows) in order to
+be accessed by the directive @option{-l@var{xxx}} at link time.
@node Installing a library
@subsection Installing a library
projects / platform / upstream / gcc.git / commitdiff