Changes since U-Boot 1.1.4:
======================================================================
+* Enable address translation on MPC83xx
+ Patch by Kumar Gala, 10 Feb 2006
+
+* Decopuled setting of OR/BR and LBLAWBAR/LBLAWAR on MPC83xx
+ Patch by Kumar Gala, 25 Jan 2006
+
+* Fixed defines for MPC83xx SICRL register to match current specs
+ Patch by Kumar Gala, 23 Jan 2006
+
+* Fixed PCI indirect config ops to handle multiple PCI controllers
+ We need to adjust the bus number we are trying to access based
+ on which PCI controller its on
+ Patch by Kumar Gala 12 Jan 2006
+
+* Add helper function for generic flat device tree fixups for mpc83xx
+ Patch by Kumar Gala 11 Jan 2006
+
+* Add support for passing initrd information via flat device tree
+ Patch by Kumar Gala 11 Jan 2006
+
+* Added OF_STDOUT_PATH and OF_SOC
+
+ OF_STDOUT_PATH specifies the path to the device the kernel can use
+ for console output
+
+ OF_SOC specifies the proper name of the SOC node if one exists.
+ Patch by Kumar Gala 11 Jan 2006
+
+* Allow board code to fixup the flat device tree before booting a
+ kernel
+ Patch by Kumar Gala 11 Jan 2006
+
+* Added CONFIG_ options for bd_t and env in flat dev tree
+
+ CONFIG_OF_HAS_BD_T will put a copy of the bd_t
+ into the resulting flat device tree.
+
+ CONFIG_OF_HAS_UBOOT_ENV will copy the environment
+ variables from u-boot into the flat device tree
+
+ Patch by Kumar Gala 11 Jan 2006
+
+* Report back PCI bus when doing table based device config
+ Patch by Kumar Gala 11 Jan 2006
+
+* Added support for PCI prefetchable region and BARs
+ If a host controller sets up a region as prefetchable and
+ a device's BAR denotes it as prefetchable, allocate the
+ BAR into the prefetch region.
+
+ If a BAR is prefetchable and no prefetchable region has
+ been setup by the controller we fall back to allocating
+ the BAR into the normally memory region.
+ Patch by Kumar Gala 11 Jan 2006
+
+* Only disable the MPC83xx watchdog if its enabled out of reset.
+ If its disabled out of reset SW can later enable it if so desired
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Allow config of GPIO direction & data registers at boot on 83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Enable time handling on 83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Make System IO Config Registers board configurable on MPC83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added PCI support for MPC8349ADS board
+ Patch by Kumar Gala 11 Jan 2006
+
* Add basic support for the SMMACO4 Board from PanDaCom.
Patch by Heiko Schocher, 20 Feb 2006
* Fix mkimage bug with multifile images created on 64 bit systems.
* Add support for 28F256J3A flash (=> 64 MB) on PM520 board
+>>>>>>> 6624b687bc2b747233090e67628df37d1c84ed17/CHANGELOG
* Fix compiler problem with at91rm9200dk board.
Patch by Eugen Bigz, 19 Dec 2005
The maximum size of the constructed OF tree.
OF_CPU - The proper name of the cpus node.
+ OF_SOC - The proper name of the soc node.
OF_TBCLK - The timebase frequency.
+ OF_STDOUT_PATH - The path to the console device
+
+ CONFIG_OF_HAS_BD_T
+
+ The resulting flat device tree will have a copy of the bd_t.
+ Space should be pre-allocated in the dts for the bd_t.
+
+ CONFIG_OF_HAS_UBOOT_ENV
+
+ The resulting flat device tree will have a copy of u-boot's
+ environment variables
+
+ CONFIG_OF_BOARD_SETUP
+
+ Board code has addition modification that it wants to make
+ to the flat device tree before handing it off to the kernel
- Serial Ports:
CFG_PL010_SERIAL
LIB = lib$(BOARD).a
-OBJS := $(BOARD).o
+OBJS := $(BOARD).o pci.o
$(LIB): $(OBJS) $(SOBJS)
$(AR) crv $@ $(OBJS)
return 0;
}
-#if defined(CONFIG_PCI)
-/*
- * Initialize PCI Devices, report devices found
- */
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_mpc83xxads_config_table[] = {
- {PCI_ANY_ID,PCI_ANY_ID,PCI_ANY_ID,PCI_ANY_ID,
- pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMON_MEMORY | PCI_COMMAND_MASTER
- } },
- {}
-}
-#endif
-
-
-volatile static struct pci_controller hose[] = {
- {
-#ifndef CONFIG_PCI_PNP
- config_table:pci_mpc83xxads_config_table,
-#endif
- },
- {
-#ifndef CONFIG_PCI_PNP
- config_table:pci_mpc83xxads_config_table,
-#endif
- }
-};
-#endif /* CONFIG_PCI */
-
-
-void
-pci_init_board(void)
-{
-#ifdef CONFIG_PCI
- extern void pci_mpc83xx_init(volatile struct pci_controller *hose);
-
- pci_mpc83xx_init(hose);
-#endif /* CONFIG_PCI */
-}
-
/*
* if MPC8349ADS is soldered with SDRAM
*/
--- /dev/null
+/*
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <asm/mmu.h>
+#include <common.h>
+#include <asm/global_data.h>
+#include <pci.h>
+#include <asm/mpc8349_pci.h>
+#include <i2c.h>
+
+#ifdef CONFIG_PCI
+
+/* System RAM mapped to PCI space */
+#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc83xxads_config_table[] = {
+ {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+ PCI_IDSEL_NUMBER, PCI_ANY_ID,
+ pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
+ PCI_ENET0_MEMADDR,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+ }
+ },
+ {}
+};
+#endif
+
+static struct pci_controller pci_hose[] = {
+ {
+#ifndef CONFIG_PCI_PNP
+ config_table:pci_mpc83xxads_config_table,
+#endif
+ },
+ {
+#ifndef CONFIG_PCI_PNP
+ config_table:pci_mpc83xxads_config_table,
+#endif
+ }
+};
+
+/**************************************************************************
+ *
+ * pib_init() -- initialize the PCA9555PW IO expander on the PIB board
+ *
+ */
+void
+pib_init(void)
+{
+ u8 val8;
+ /*
+ * Assign PIB PMC slot to desired PCI bus
+ */
+ mpc8349_i2c = (i2c_t*)(CFG_IMMRBAR + CFG_I2C2_OFFSET);
+ i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
+
+ val8 = 0;
+ i2c_write(0x23, 0x6, 1, &val8, 1);
+ i2c_write(0x23, 0x7, 1, &val8, 1);
+ val8 = 0xff;
+ i2c_write(0x23, 0x2, 1, &val8, 1);
+ i2c_write(0x23, 0x3, 1, &val8, 1);
+
+ val8 = 0;
+ i2c_write(0x26, 0x6, 1, &val8, 1);
+ val8 = 0x34;
+ i2c_write(0x26, 0x7, 1, &val8, 1);
+#if defined(PCI_64BIT)
+ val8 = 0xf4; /* PMC2:PCI1/64-bit */
+#elif defined(PCI_ALL_PCI1)
+ val8 = 0xf3; /* PMC1:PCI1 PMC2:PCI1 PMC3:PCI1 */
+#elif defined(PCI_ONE_PCI1)
+ val8 = 0xf9; /* PMC1:PCI1 PMC2:PCI2 PMC3:PCI2 */
+#else
+ val8 = 0xf5; /* PMC1:PCI1 PMC2:PCI1 PMC3:PCI2 */
+#endif
+ i2c_write(0x26, 0x2, 1, &val8, 1);
+ val8 = 0xff;
+ i2c_write(0x26, 0x3, 1, &val8, 1);
+ val8 = 0;
+ i2c_write(0x27, 0x6, 1, &val8, 1);
+ i2c_write(0x27, 0x7, 1, &val8, 1);
+ val8 = 0xff;
+ i2c_write(0x27, 0x2, 1, &val8, 1);
+ val8 = 0xef;
+ i2c_write(0x27, 0x3, 1, &val8, 1);
+ asm("eieio");
+
+#if defined(PCI_64BIT)
+ printf("PCI1: 64-bit on PMC2\n");
+#elif defined(PCI_ALL_PCI1)
+ printf("PCI1: 32-bit on PMC1, PMC2, PMC3\n");
+#elif defined(PCI_ONE_PCI1)
+ printf("PCI1: 32-bit on PMC1\n");
+ printf("PCI2: 32-bit on PMC2, PMC3\n");
+#else
+ printf("PCI1: 32-bit on PMC1, PMC2\n");
+ printf("PCI2: 32-bit on PMC3\n");
+#endif
+}
+
+/**************************************************************************
+ * pci_init_board()
+ *
+ * NOTICE: PCI2 is not currently supported
+ *
+ */
+void
+pci_init_board(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ volatile immap_t * immr;
+ volatile clk8349_t * clk;
+ volatile law8349_t * pci_law;
+ volatile pot8349_t * pci_pot;
+ volatile pcictrl8349_t * pci_ctrl;
+ volatile pciconf8349_t * pci_conf;
+ u16 reg16;
+ u32 reg32;
+ u32 dev;
+ struct pci_controller * hose;
+
+ immr = (immap_t *)CFG_IMMRBAR;
+ clk = (clk8349_t *)&immr->clk;
+ pci_law = immr->sysconf.pcilaw;
+ pci_pot = immr->ios.pot;
+ pci_ctrl = immr->pci_ctrl;
+ pci_conf = immr->pci_conf;
+
+ hose = &pci_hose[0];
+
+ pib_init();
+
+ /*
+ * Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode
+ */
+
+ reg32 = clk->occr;
+ udelay(2000);
+ clk->occr = 0xff000000;
+ udelay(2000);
+
+ /*
+ * Release PCI RST Output signal
+ */
+ pci_ctrl[0].gcr = 0;
+ udelay(2000);
+ pci_ctrl[0].gcr = 1;
+
+#ifdef CONFIG_MPC83XX_PCI2
+ pci_ctrl[1].gcr = 0;
+ udelay(2000);
+ pci_ctrl[1].gcr = 1;
+#endif
+
+ /* We need to wait at least a 1sec based on PCI specs */
+ {
+ int i;
+
+ for (i = 0; i < 1000; ++i)
+ udelay (1000);
+ }
+
+ /*
+ * Configure PCI Local Access Windows
+ */
+ pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR;
+ pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
+
+ pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR;
+ pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_32M;
+
+ /*
+ * Configure PCI Outbound Translation Windows
+ */
+
+ /* PCI1 mem space - prefetch */
+ pci_pot[0].potar = (CFG_PCI1_MEM_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[0].pobar = (CFG_PCI1_MEM_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[0].pocmr = POCMR_EN | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK);
+
+ /* PCI1 IO space */
+ pci_pot[1].potar = (CFG_PCI1_IO_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[1].pobar = (CFG_PCI1_IO_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[1].pocmr = POCMR_EN | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK);
+
+ /* PCI1 mmio - non-prefetch mem space */
+ pci_pot[2].potar = (CFG_PCI1_MMIO_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[2].pobar = (CFG_PCI1_MMIO_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[2].pocmr = POCMR_EN | (POCMR_CM_256M & POCMR_CM_MASK);
+
+ /*
+ * Configure PCI Inbound Translation Windows
+ */
+
+ /* we need RAM mapped to PCI space for the devices to
+ * access main memory */
+ pci_ctrl[0].pitar1 = 0x0;
+ pci_ctrl[0].pibar1 = 0x0;
+ pci_ctrl[0].piebar1 = 0x0;
+ pci_ctrl[0].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
+
+ hose->first_busno = 0;
+ hose->last_busno = 0xff;
+
+ /* PCI memory prefetch space */
+ pci_set_region(hose->regions + 0,
+ CFG_PCI1_MEM_BASE,
+ CFG_PCI1_MEM_PHYS,
+ CFG_PCI1_MEM_SIZE,
+ PCI_REGION_MEM|PCI_REGION_PREFETCH);
+
+ /* PCI memory space */
+ pci_set_region(hose->regions + 1,
+ CFG_PCI1_MMIO_BASE,
+ CFG_PCI1_MMIO_PHYS,
+ CFG_PCI1_MMIO_SIZE,
+ PCI_REGION_MEM);
+
+ /* PCI IO space */
+ pci_set_region(hose->regions + 2,
+ CFG_PCI1_IO_BASE,
+ CFG_PCI1_IO_PHYS,
+ CFG_PCI1_IO_SIZE,
+ PCI_REGION_IO);
+
+ /* System memory space */
+ pci_set_region(hose->regions + 3,
+ CONFIG_PCI_SYS_MEM_BUS,
+ CONFIG_PCI_SYS_MEM_PHYS,
+ gd->ram_size,
+ PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+ hose->region_count = 4;
+
+ pci_setup_indirect(hose,
+ (CFG_IMMRBAR+0x8300),
+ (CFG_IMMRBAR+0x8304));
+
+ pci_register_hose(hose);
+
+ /*
+ * Write to Command register
+ */
+ reg16 = 0xff;
+ dev = PCI_BDF(hose->first_busno, 0, 0);
+ pci_hose_read_config_word (hose, dev, PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
+ pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
+ pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
+
+#ifdef CONFIG_PCI_SCAN_SHOW
+ printf("PCI: Bus Dev VenId DevId Class Int\n");
+#endif
+ /*
+ * Hose scan.
+ */
+ hose->last_busno = pci_hose_scan(hose);
+
+#ifdef CONFIG_MPC83XX_PCI2
+ hose = &pci_hose[1];
+
+ /*
+ * Configure PCI Outbound Translation Windows
+ */
+
+ /* PCI2 mem space - prefetch */
+ pci_pot[3].potar = (CFG_PCI2_MEM_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[3].pobar = (CFG_PCI2_MEM_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[3].pocmr = POCMR_EN | POCMR_PCI2 | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK);
+
+ /* PCI2 IO space */
+ pci_pot[4].potar = (CFG_PCI2_IO_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[4].pobar = (CFG_PCI2_IO_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[4].pocmr = POCMR_EN | POCMR_PCI2 | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK);
+
+ /* PCI2 mmio - non-prefetch mem space */
+ pci_pot[5].potar = (CFG_PCI2_MMIO_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[5].pobar = (CFG_PCI2_MMIO_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[5].pocmr = POCMR_EN | POCMR_PCI2 | (POCMR_CM_256M & POCMR_CM_MASK);
+
+ /*
+ * Configure PCI Inbound Translation Windows
+ */
+
+ /* we need RAM mapped to PCI space for the devices to
+ * access main memory */
+ pci_ctrl[1].pitar1 = 0x0;
+ pci_ctrl[1].pibar1 = 0x0;
+ pci_ctrl[1].piebar1 = 0x0;
+ pci_ctrl[1].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
+
+ hose->first_busno = pci_hose[0].last_busno + 1;
+ hose->last_busno = 0xff;
+
+ /* PCI memory prefetch space */
+ pci_set_region(hose->regions + 0,
+ CFG_PCI2_MEM_BASE,
+ CFG_PCI2_MEM_PHYS,
+ CFG_PCI2_MEM_SIZE,
+ PCI_REGION_MEM|PCI_REGION_PREFETCH);
+
+ /* PCI memory space */
+ pci_set_region(hose->regions + 1,
+ CFG_PCI2_MMIO_BASE,
+ CFG_PCI2_MMIO_PHYS,
+ CFG_PCI2_MMIO_SIZE,
+ PCI_REGION_MEM);
+
+ /* PCI IO space */
+ pci_set_region(hose->regions + 2,
+ CFG_PCI2_IO_BASE,
+ CFG_PCI2_IO_PHYS,
+ CFG_PCI2_IO_SIZE,
+ PCI_REGION_IO);
+
+ /* System memory space */
+ pci_set_region(hose->regions + 3,
+ CONFIG_PCI_SYS_MEM_BUS,
+ CONFIG_PCI_SYS_MEM_PHYS,
+ gd->ram_size,
+ PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+ hose->region_count = 4;
+
+ pci_setup_indirect(hose,
+ (CFG_IMMRBAR+0x8380),
+ (CFG_IMMRBAR+0x8384));
+
+ pci_register_hose(hose);
+
+ /*
+ * Write to Command register
+ */
+ reg16 = 0xff;
+ dev = PCI_BDF(hose->first_busno, 0, 0);
+ pci_hose_read_config_word (hose, dev, PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
+ pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
+ pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
+
+ /*
+ * Hose scan.
+ */
+ hose->last_busno = pci_hose_scan(hose);
+#endif
+
+}
+#endif /* CONFIG_PCI */
(*kernel) (kbd, initrd_start, initrd_end, cmd_start, cmd_end);
#else
- ft_setup(of_flat_tree, OF_FLAT_TREE_MAX_SIZE, kbd);
+ ft_setup(of_flat_tree, OF_FLAT_TREE_MAX_SIZE, kbd, initrd_start, initrd_end);
/* ft_dump_blob(of_flat_tree); */
#if defined(CFG_INIT_RAM_LOCK) && !defined(CONFIG_E500)
/*
* Linux Kernel Parameters:
* r3: ptr to OF flat tree, followed by the board info data
- * r4: initrd_start or 0 if no initrd
- * r5: initrd_end - unused if r4 is 0
- * r6: Start of command line string
- * r7: End of command line string
+ * r4: physical pointer to the kernel itself
+ * r5: NULL
+ * r6: NULL
+ * r7: NULL
*/
- (*kernel) ((bd_t *)of_flat_tree, initrd_start, initrd_end, cmd_start, cmd_end);
+ if (getenv("disable_of") != NULL)
+ (*kernel) ((bd_t *)of_flat_tree, initrd_start, initrd_end,
+ cmd_start, cmd_end);
+ else
+ (*kernel) ((bd_t *)of_flat_tree, (ulong)kernel, 0, 0, 0);
#endif
}
((u64 *) cxt->pres)[0] = cpu_to_be64(physaddr); /* phys = 0, size = 0, terminate */
((u64 *) cxt->pres)[1] = cpu_to_be64(size);
- cxt->pres += 18; /* advance */
+ cxt->pres += 16; /* advance */
((u64 *) cxt->pres)[0] = 0; /* phys = 0, size = 0, terminate */
((u64 *) cxt->pres)[1] = 0;
#define BDM(x) { .name = #x, .offset = offsetof(bd_t, bi_ ##x ) }
+#ifdef CONFIG_OF_HAS_BD_T
static const struct {
const char *name;
int offset;
#endif
BDM(baudrate),
};
+#endif
-void ft_setup(void *blob, int size, bd_t * bd)
+void ft_setup(void *blob, int size, bd_t * bd, ulong initrd_start, ulong initrd_end)
{
- DECLARE_GLOBAL_DATA_PTR;
- u8 *end;
u32 *p;
int len;
struct ft_cxt cxt;
- int i, k, nxt;
- static char tmpenv[256];
- char *s, *lval, *rval;
ulong clock;
- uint32_t v;
+#if defined(CONFIG_OF_HAS_UBOOT_ENV)
+ int k, nxt;
+#endif
+#if defined(CONFIG_OF_HAS_BD_T)
+ u8 *end;
+#endif
+#if defined(CONFIG_OF_HAS_UBOOT_ENV) || defined(CONFIG_OF_HAS_BD_T)
+ int i;
+ static char tmpenv[256];
+#endif
/* disable OF tree; booting old kernel */
if (getenv("disable_of") != NULL) {
ft_begin(&cxt, blob, size);
- /* fs_add_rsvmap not used */
+ if (initrd_start && initrd_end)
+ ft_add_rsvmap(&cxt, initrd_start, initrd_end - initrd_start + 1);
ft_begin_tree(&cxt);
/* back into root */
ft_backtrack_node(&cxt);
+#ifdef CONFIG_OF_HAS_UBOOT_ENV
ft_begin_node(&cxt, "u-boot-env");
for (i = 0; env_get_char(i) != '\0'; i = nxt + 1) {
+ char *s, *lval, *rval;
+
for (nxt = i; env_get_char(nxt) != '\0'; ++nxt) ;
s = tmpenv;
for (k = i; k < nxt && s < &tmpenv[sizeof(tmpenv) - 1]; ++k)
}
ft_end_node(&cxt);
+#endif
ft_begin_node(&cxt, "chosen");
ft_prop_str(&cxt, "name", "chosen");
ft_prop_str(&cxt, "bootargs", getenv("bootargs"));
ft_prop_int(&cxt, "linux,platform", 0x600); /* what is this? */
+ if (initrd_start && initrd_end) {
+ ft_prop_int(&cxt, "linux,initrd-start", initrd_start);
+ ft_prop_int(&cxt, "linux,initrd-end", initrd_end);
+ }
+#ifdef OF_STDOUT_PATH
+ ft_prop_str(&cxt, "linux,stdout-path", OF_STDOUT_PATH);
+#endif
ft_end_node(&cxt);
ft_dump_blob(blob);
*/
+#ifdef CONFIG_OF_HAS_BD_T
/* paste the bd_t at the end of the flat tree */
end = (char *)blob +
be32_to_cpu(((struct boot_param_header *)blob)->totalsize);
memcpy(end, bd, sizeof(*bd));
+#endif
#ifdef CONFIG_PPC
+#ifdef CONFIG_OF_HAS_BD_T
for (i = 0; i < sizeof(bd_map)/sizeof(bd_map[0]); i++) {
+ uint32_t v;
+
sprintf(tmpenv, "/bd_t/%s", bd_map[i].name);
v = *(uint32_t *)((char *)bd + bd_map[i].offset);
p = ft_get_prop(blob, "/bd_t/ethspeed", &len);
if (p != NULL)
*p = cpu_to_be32((uint32_t) bd->bi_ethspeed);
+#endif
clock = bd->bi_intfreq;
p = ft_get_prop(blob, "/cpus/" OF_CPU "/clock-frequency", &len);
clock = OF_TBCLK;
p = ft_get_prop(blob, "/cpus/" OF_CPU "/timebase-frequency", &len);
if (p != NULL)
- *p = cpu_to_be32(OF_TBCLK);
+ *p = cpu_to_be32(clock);
#endif
-
#endif /* __powerpc__ */
+#ifdef CONFIG_OF_BOARD_SETUP
+ ft_board_setup(blob, bd);
+#endif
+
/*
printf("final OF-tree\n");
ft_dump_blob(blob);
#include <watchdog.h>
#include <command.h>
#include <mpc83xx.h>
+#include <ft_build.h>
#include <asm/processor.h>
hang(); /* FIXME: implement watchdog_reset()? */
}
#endif /* CONFIG_WATCHDOG */
+
+#if defined(CONFIG_OF_FLAT_TREE)
+void
+ft_cpu_setup(void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+ ulong clock;
+
+ clock = bd->bi_busfreq;
+ p = ft_get_prop(blob, "/cpus/" OF_CPU "/bus-frequency", &len);
+ if (p != NULL)
+ *p = cpu_to_be32(clock);
+
+ p = ft_get_prop(blob, "/" OF_SOC "/bus-frequency", &len);
+ if (p != NULL)
+ *p = cpu_to_be32(clock);
+
+ p = ft_get_prop(blob, "/" OF_SOC "/serial@4500/clock-frequency", &len);
+ if (p != NULL)
+ *p = cpu_to_be32(clock);
+
+ p = ft_get_prop(blob, "/" OF_SOC "/serial@4600/clock-frequency", &len);
+ if (p != NULL)
+ *p = cpu_to_be32(clock);
+
+#ifdef CONFIG_MPC83XX_TSEC1
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/address", &len);
+ memcpy(p, bd->bi_enetaddr, 6);
+#endif
+
+#ifdef CONFIG_MPC83XX_TSEC2
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/address", &len);
+ memcpy(p, bd->bi_enet1addr, 6);
+#endif
+}
+#endif
im->sysconf.spcr |= SPCR_TBEN;
/* System General Purpose Register */
- im->sysconf.sicrh = SICRH_TSOBI1;
- im->sysconf.sicrl = SICRL_LDP_A;
+#ifdef CFG_SICRH
+ im->sysconf.sicrh = CFG_SICRH;
+#endif
+#ifdef CFG_SICRL
+ im->sysconf.sicrl = CFG_SICRL;
+#endif
/*
* Memory Controller:
#error CFG_BR0_PRELIM, CFG_OR0_PRELIM, CFG_LBLAWBAR0_PRELIM & CFG_LBLAWAR0_PRELIM must be defined
#endif
-#if defined(CFG_BR1_PRELIM) \
- && defined(CFG_OR1_PRELIM) \
- && defined(CFG_LBLAWBAR1_PRELIM) \
- && defined(CFG_LBLAWAR1_PRELIM)
+#if defined(CFG_BR1_PRELIM) && defined(CFG_OR1_PRELIM)
im->lbus.bank[1].br = CFG_BR1_PRELIM;
im->lbus.bank[1].or = CFG_OR1_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR1_PRELIM) && defined(CFG_LBLAWAR1_PRELIM)
im->sysconf.lblaw[1].bar = CFG_LBLAWBAR1_PRELIM;
im->sysconf.lblaw[1].ar = CFG_LBLAWAR1_PRELIM;
#endif
-#if defined(CFG_BR2_PRELIM) \
- && defined(CFG_OR2_PRELIM) \
- && defined(CFG_LBLAWBAR2_PRELIM) \
- && defined(CFG_LBLAWAR2_PRELIM)
+#if defined(CFG_BR2_PRELIM) && defined(CFG_OR2_PRELIM)
im->lbus.bank[2].br = CFG_BR2_PRELIM;
im->lbus.bank[2].or = CFG_OR2_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR2_PRELIM) && defined(CFG_LBLAWAR2_PRELIM)
im->sysconf.lblaw[2].bar = CFG_LBLAWBAR2_PRELIM;
im->sysconf.lblaw[2].ar = CFG_LBLAWAR2_PRELIM;
#endif
-#if defined(CFG_BR3_PRELIM) \
- && defined(CFG_OR3_PRELIM) \
- && defined(CFG_LBLAWBAR3_PRELIM) \
- && defined(CFG_LBLAWAR3_PRELIM)
+#if defined(CFG_BR3_PRELIM) && defined(CFG_OR3_PRELIM)
im->lbus.bank[3].br = CFG_BR3_PRELIM;
im->lbus.bank[3].or = CFG_OR3_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR3_PRELIM) && defined(CFG_LBLAWAR3_PRELIM)
im->sysconf.lblaw[3].bar = CFG_LBLAWBAR3_PRELIM;
im->sysconf.lblaw[3].ar = CFG_LBLAWAR3_PRELIM;
#endif
-#if defined(CFG_BR4_PRELIM) \
- && defined(CFG_OR4_PRELIM) \
- && defined(CFG_LBLAWBAR4_PRELIM) \
- && defined(CFG_LBLAWAR4_PRELIM)
+#if defined(CFG_BR4_PRELIM) && defined(CFG_OR4_PRELIM)
im->lbus.bank[4].br = CFG_BR4_PRELIM;
im->lbus.bank[4].or = CFG_OR4_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR4_PRELIM) && defined(CFG_LBLAWAR4_PRELIM)
im->sysconf.lblaw[4].bar = CFG_LBLAWBAR4_PRELIM;
im->sysconf.lblaw[4].ar = CFG_LBLAWAR4_PRELIM;
#endif
-#if defined(CFG_BR5_PRELIM) \
- && defined(CFG_OR5_PRELIM) \
- && defined(CFG_LBLAWBAR5_PRELIM) \
- && defined(CFG_LBLAWAR5_PRELIM)
+#if defined(CFG_BR5_PRELIM) && defined(CFG_OR5_PRELIM)
im->lbus.bank[5].br = CFG_BR5_PRELIM;
im->lbus.bank[5].or = CFG_OR5_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR5_PRELIM) && defined(CFG_LBLAWAR5_PRELIM)
im->sysconf.lblaw[5].bar = CFG_LBLAWBAR5_PRELIM;
im->sysconf.lblaw[5].ar = CFG_LBLAWAR5_PRELIM;
#endif
-#if defined(CFG_BR6_PRELIM) \
- && defined(CFG_OR6_PRELIM) \
- && defined(CFG_LBLAWBAR6_PRELIM) \
- && defined(CFG_LBLAWAR6_PRELIM)
+#if defined(CFG_BR6_PRELIM) && defined(CFG_OR6_PRELIM)
im->lbus.bank[6].br = CFG_BR6_PRELIM;
im->lbus.bank[6].or = CFG_OR6_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR6_PRELIM) && defined(CFG_LBLAWAR6_PRELIM)
im->sysconf.lblaw[6].bar = CFG_LBLAWBAR6_PRELIM;
im->sysconf.lblaw[6].ar = CFG_LBLAWAR6_PRELIM;
#endif
-#if defined(CFG_BR7_PRELIM) \
- && defined(CFG_OR7_PRELIM) \
- && defined(CFG_LBLAWBAR7_PRELIM) \
- && defined(CFG_LBLAWAR7_PRELIM)
+#if defined(CFG_BR7_PRELIM) && defined(CFG_OR7_PRELIM)
im->lbus.bank[7].br = CFG_BR7_PRELIM;
im->lbus.bank[7].or = CFG_OR7_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR7_PRELIM) && defined(CFG_LBLAWAR7_PRELIM)
im->sysconf.lblaw[7].bar = CFG_LBLAWBAR7_PRELIM;
im->sysconf.lblaw[7].ar = CFG_LBLAWAR7_PRELIM;
#endif
+#ifdef CFG_GPIO1_PRELIM
+ im->pgio[0].dir = CFG_GPIO1_DIR;
+ im->pgio[0].dat = CFG_GPIO1_DAT;
+#endif
+#ifdef CFG_GPIO2_PRELIM
+ im->pgio[1].dir = CFG_GPIO2_DIR;
+ im->pgio[1].dat = CFG_GPIO2_DAT;
+#endif
}
int interrupt_init_cpu (unsigned *decrementer_count)
{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ volatile immap_t *immr = (immap_t *) CFG_IMMRBAR;
+
+ *decrementer_count = (gd->bus_clk / 4) / CFG_HZ;
+
+ /* Enable e300 time base */
+
+ immr->sysconf.spcr |= 0x00400000;
+
return 0;
}
#endif
#endif /* CFG_RAMBOOT */
- bl setup_stack_in_data_cache_on_r1
+ /* setup the bats */
+ bl setup_bats
+ sync
+
+ /*
+ * Cache must be enabled here for stack-in-cache trick.
+ * This means we need to enable the BATS.
+ * This means:
+ * 1) for the EVB, original gt regs need to be mapped
+ * 2) need to have an IBAT for the 0xf region,
+ * we are running there!
+ * Cache should be turned on after BATs, since by default
+ * everything is write-through.
+ * The init-mem BAT can be reused after reloc. The old
+ * gt-regs BAT can be reused after board_init_f calls
+ * board_early_init_f (EVB only).
+ */
+ /* enable address translation */
+ bl enable_addr_trans
+ sync
+
+ /* enable and invalidate the data cache */
+ bl dcache_enable
+ sync
+#ifdef CFG_INIT_RAM_LOCK
+ bl lock_ram_in_cache
+ sync
+#endif
+
+ /* set up the stack pointer in our newly created
+ * cache-ram (r1) */
+ lis r1, (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET)@h
+ ori r1, r1, (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET)@l
+
+ li r0, 0 /* Make room for stack frame header and */
+ stwu r0, -4(r1) /* clear final stack frame so that */
+ stwu r0, -4(r1) /* stack backtraces terminate cleanly */
+
/* let the C-code set up the rest */
- /* */
+ /* */
/* Be careful to keep code relocatable & stack humble */
/*------------------------------------------------------*/
#else
/* Disable Wathcdog */
/*-------------------*/
+ lwz r4, SWCRR(r3)
+ /* Check to see if its enabled for disabling
+ once disabled by SW you can't re-enable */
+ andi. r4, r4, 0x4
+ beq 1f
xor r4, r4, r4
stw r4, SWCRR(r3)
+1:
#endif /* CONFIG_WATCHDOG */
/* Initialize the Hardware Implementation-dependent Registers */
/*------------------------------*/
blr
+ .globl invalidate_bats
+invalidate_bats:
+ /* invalidate BATs */
+ mtspr IBAT0U, r0
+ mtspr IBAT1U, r0
+ mtspr IBAT2U, r0
+ mtspr IBAT3U, r0
+#if (CFG_HID2 & HID2_HBE)
+ mtspr IBAT4U, r0
+ mtspr IBAT5U, r0
+ mtspr IBAT6U, r0
+ mtspr IBAT7U, r0
+#endif
+ isync
+ mtspr DBAT0U, r0
+ mtspr DBAT1U, r0
+ mtspr DBAT2U, r0
+ mtspr DBAT3U, r0
+#if (CFG_HID2 & HID2_HBE)
+ mtspr DBAT4U, r0
+ mtspr DBAT5U, r0
+ mtspr DBAT6U, r0
+ mtspr DBAT7U, r0
+#endif
+ isync
+ sync
+ blr
+
+ /* setup_bats - set them up to some initial state */
+ .globl setup_bats
+setup_bats:
+ addis r0, r0, 0x0000
+
+ /* IBAT 0 */
+ addis r4, r0, CFG_IBAT0L@h
+ ori r4, r4, CFG_IBAT0L@l
+ addis r3, r0, CFG_IBAT0U@h
+ ori r3, r3, CFG_IBAT0U@l
+ mtspr IBAT0L, r4
+ mtspr IBAT0U, r3
+ isync
+
+ /* DBAT 0 */
+ addis r4, r0, CFG_DBAT0L@h
+ ori r4, r4, CFG_DBAT0L@l
+ addis r3, r0, CFG_DBAT0U@h
+ ori r3, r3, CFG_DBAT0U@l
+ mtspr DBAT0L, r4
+ mtspr DBAT0U, r3
+ isync
+
+ /* IBAT 1 */
+ addis r4, r0, CFG_IBAT1L@h
+ ori r4, r4, CFG_IBAT1L@l
+ addis r3, r0, CFG_IBAT1U@h
+ ori r3, r3, CFG_IBAT1U@l
+ mtspr IBAT1L, r4
+ mtspr IBAT1U, r3
+ isync
+
+ /* DBAT 1 */
+ addis r4, r0, CFG_DBAT1L@h
+ ori r4, r4, CFG_DBAT1L@l
+ addis r3, r0, CFG_DBAT1U@h
+ ori r3, r3, CFG_DBAT1U@l
+ mtspr DBAT1L, r4
+ mtspr DBAT1U, r3
+ isync
+
+ /* IBAT 2 */
+ addis r4, r0, CFG_IBAT2L@h
+ ori r4, r4, CFG_IBAT2L@l
+ addis r3, r0, CFG_IBAT2U@h
+ ori r3, r3, CFG_IBAT2U@l
+ mtspr IBAT2L, r4
+ mtspr IBAT2U, r3
+ isync
+
+ /* DBAT 2 */
+ addis r4, r0, CFG_DBAT2L@h
+ ori r4, r4, CFG_DBAT2L@l
+ addis r3, r0, CFG_DBAT2U@h
+ ori r3, r3, CFG_DBAT2U@l
+ mtspr DBAT2L, r4
+ mtspr DBAT2U, r3
+ isync
+
+ /* IBAT 3 */
+ addis r4, r0, CFG_IBAT3L@h
+ ori r4, r4, CFG_IBAT3L@l
+ addis r3, r0, CFG_IBAT3U@h
+ ori r3, r3, CFG_IBAT3U@l
+ mtspr IBAT3L, r4
+ mtspr IBAT3U, r3
+ isync
+
+ /* DBAT 3 */
+ addis r4, r0, CFG_DBAT3L@h
+ ori r4, r4, CFG_DBAT3L@l
+ addis r3, r0, CFG_DBAT3U@h
+ ori r3, r3, CFG_DBAT3U@l
+ mtspr DBAT3L, r4
+ mtspr DBAT3U, r3
+ isync
+
+#if (CFG_HID2 & HID2_HBE)
+ /* IBAT 4 */
+ addis r4, r0, CFG_IBAT4L@h
+ ori r4, r4, CFG_IBAT4L@l
+ addis r3, r0, CFG_IBAT4U@h
+ ori r3, r3, CFG_IBAT4U@l
+ mtspr IBAT4L, r4
+ mtspr IBAT4U, r3
+ isync
+
+ /* DBAT 4 */
+ addis r4, r0, CFG_DBAT4L@h
+ ori r4, r4, CFG_DBAT4L@l
+ addis r3, r0, CFG_DBAT4U@h
+ ori r3, r3, CFG_DBAT4U@l
+ mtspr DBAT4L, r4
+ mtspr DBAT4U, r3
+ isync
+
+ /* IBAT 5 */
+ addis r4, r0, CFG_IBAT5L@h
+ ori r4, r4, CFG_IBAT5L@l
+ addis r3, r0, CFG_IBAT5U@h
+ ori r3, r3, CFG_IBAT5U@l
+ mtspr IBAT5L, r4
+ mtspr IBAT5U, r3
+ isync
+
+ /* DBAT 5 */
+ addis r4, r0, CFG_DBAT5L@h
+ ori r4, r4, CFG_DBAT5L@l
+ addis r3, r0, CFG_DBAT5U@h
+ ori r3, r3, CFG_DBAT5U@l
+ mtspr DBAT5L, r4
+ mtspr DBAT5U, r3
+ isync
+
+ /* IBAT 6 */
+ addis r4, r0, CFG_IBAT6L@h
+ ori r4, r4, CFG_IBAT6L@l
+ addis r3, r0, CFG_IBAT6U@h
+ ori r3, r3, CFG_IBAT6U@l
+ mtspr IBAT6L, r4
+ mtspr IBAT6U, r3
+ isync
+
+ /* DBAT 6 */
+ addis r4, r0, CFG_DBAT6L@h
+ ori r4, r4, CFG_DBAT6L@l
+ addis r3, r0, CFG_DBAT6U@h
+ ori r3, r3, CFG_DBAT6U@l
+ mtspr DBAT6L, r4
+ mtspr DBAT6U, r3
+ isync
+
+ /* IBAT 7 */
+ addis r4, r0, CFG_IBAT7L@h
+ ori r4, r4, CFG_IBAT7L@l
+ addis r3, r0, CFG_IBAT7U@h
+ ori r3, r3, CFG_IBAT7U@l
+ mtspr IBAT7L, r4
+ mtspr IBAT7U, r3
+ isync
+
+ /* DBAT 7 */
+ addis r4, r0, CFG_DBAT7L@h
+ ori r4, r4, CFG_DBAT7L@l
+ addis r3, r0, CFG_DBAT7U@h
+ ori r3, r3, CFG_DBAT7U@l
+ mtspr DBAT7L, r4
+ mtspr DBAT7U, r3
+ isync
+#endif
+
+ /* Invalidate TLBs.
+ * -> for (val = 0; val < 0x20000; val+=0x1000)
+ * -> tlbie(val);
+ */
+ lis r3, 0
+ lis r5, 2
+
+1:
+ tlbie r3
+ addi r3, r3, 0x1000
+ cmp 0, 0, r3, r5
+ blt 1b
+
+ blr
+
+ .globl enable_addr_trans
+enable_addr_trans:
+ /* enable address translation */
+ mfmsr r5
+ ori r5, r5, (MSR_IR | MSR_DR)
+ mtmsr r5
+ isync
+ blr
+
+ .globl disable_addr_trans
+disable_addr_trans:
+ /* disable address translation */
+ mflr r4
+ mfmsr r3
+ andi. r0, r3, (MSR_IR | MSR_DR)
+ beqlr
+ andc r3, r3, r0
+ mtspr SRR0, r4
+ mtspr SRR1, r3
+ rfi
+
/* Cache functions.
*
* Note: requires that all cache bits in
.globl dcache_enable
dcache_enable:
mfspr r3, HID0
- ori r3, r3, HID0_ENABLE_DATA_CACHE
- lis r4, 0
- ori r4, r4, HID0_LOCK_DATA_CACHE
- andc r3, r3, r4
- ori r4, r3, HID0_LOCK_INSTRUCTION_CACHE
+ li r5, HID0_DCFI|HID0_DLOCK
+ andc r3, r3, r5
+ mtspr HID0, r3 /* no invalidate, unlock */
+ ori r3, r3, HID0_DCE
+ ori r5, r3, HID0_DCFI
+ mtspr HID0, r5 /* enable + invalidate */
+ mtspr HID0, r3 /* enable */
sync
- mtspr HID0, r4 /* sets enable and invalidate, clears lock */
- sync
- mtspr HID0, r3 /* clears invalidate */
blr
.globl dcache_disable
dcache_disable:
mfspr r3, HID0
lis r4, 0
- ori r4, r4, HID0_ENABLE_DATA_CACHE|HID0_LOCK_DATA_CACHE
+ ori r4, r4, HID0_DCE|HID0_DLOCK
andc r3, r3, r4
- ori r4, r3, HID0_INVALIDATE_DATA_CACHE
+ ori r4, r3, HID0_DCI
sync
- mtspr HID0, r4 /* sets invalidate, clears enable and lock */
+ mtspr HID0, r4 /* sets invalidate, clears enable and lock */
sync
mtspr HID0, r3 /* clears invalidate */
blr
* Now flush the cache: note that we must start from a cache aligned
* address. Otherwise we might miss one cache line.
*/
-4:
- bl un_setup_stack_in_data_cache
- mr r7, r3
- mr r8, r4
- bl dcache_disable
- mr r3, r7
- mr r4, r8
-
- cmpwi r6,0
+4: cmpwi r6,0
add r5,r3,r5
- beq 7f /* Always flush prefetch queue in any case */
+ beq 7f /* Always flush prefetch queue in any case */
subi r0,r6,1
andc r3,r3,r0
- mfspr r7,HID0 /* don't do dcbst if dcache is disabled*/
- rlwinm r7,r7,HID0_DCE_SHIFT,31,31
- cmpwi r7,0
- beq 9f
mr r4,r3
5: dcbst 0,r4
add r4,r4,r6
cmplw r4,r5
blt 5b
- sync /* Wait for all dcbst to complete on bus */
-9: mfspr r7,HID0 /* don't do icbi if icache is disabled */
- rlwinm r7,r7,HID0_DCE_SHIFT,31,31
- cmpwi r7,0
- beq 7f
+ sync /* Wait for all dcbst to complete on bus */
mr r4,r3
6: icbi 0,r4
add r4,r4,r6
cmplw r4,r5
blt 6b
-7: sync /* Wait for all icbi to complete on bus */
+7: sync /* Wait for all icbi to complete on bus */
isync
/*
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/
-
addi r0, r10, in_ram - _start + EXC_OFF_SYS_RESET
mtlr r0
blr
blr
#ifdef CFG_INIT_RAM_LOCK
+lock_ram_in_cache:
+ /* Allocate Initial RAM in data cache.
+ */
+ lis r3, (CFG_INIT_RAM_ADDR & ~31)@h
+ ori r3, r3, (CFG_INIT_RAM_ADDR & ~31)@l
+ li r2, ((CFG_INIT_RAM_END & ~31) + \
+ (CFG_INIT_RAM_ADDR & 31) + 31) / 32
+ mtctr r2
+1:
+ dcbz r0, r3
+ addi r3, r3, 32
+ bdnz 1b
+
+ /* Lock the data cache */
+ mfspr r0, HID0
+ ori r0, r0, 0x1000
+ sync
+ mtspr HID0, r0
+ sync
+ blr
+
.globl unlock_ram_in_cache
unlock_ram_in_cache:
/* invalidate the INIT_RAM section */
bdnz 1b
sync /* Wait for all icbi to complete on bus */
isync
+
+ /* Unlock the data cache and invalidate it */
+ mfspr r3, HID0
+ li r5, HID0_DLOCK|HID0_DCFI
+ andc r3, r3, r5 /* no invalidate, unlock */
+ ori r5, r3, HID0_DCFI /* invalidate, unlock */
+ mtspr HID0, r5 /* invalidate, unlock */
+ mtspr HID0, r3 /* no invalidate, unlock */
+ sync
blr
#endif
stw r4, LBLAWBAR1(r3)
stw r4, LBLAWAR1(r3) /* Off LBIU LAW1 */
blr
-
-setup_stack_in_data_cache_on_r1:
- lis r3, (CFG_IMMRBAR)@h
-
- /* setup D-BAT for the D-Cache (with out real memory backup) */
-
- lis r4, (CFG_INIT_RAM_ADDR & 0xFFFE0000)@h
- mtspr DBAT0U, r4
- ori r4, r4, 0x0002
- mtspr DBAT0L, r4
- isync
-
-#if 0
- /* Enable MMU */
- mfmsr r4
- ori r4, r4, (MSR_DR | MSR_IR)@l
- mtmsr r4
-#endif
-
- /* Enable and invalidate data cache. */
- mfspr r4, HID0
- mr r5, r4
- ori r4, r4, HID0_DCE | HID0_DCI
- ori r5, r5, HID0_DCE
- sync
- mtspr HID0, r4
- mtspr HID0, r5
- sync
-
- /* Allocate Initial RAM in data cache.*/
- li r0, 0
- lis r4, (CFG_INIT_RAM_ADDR)@h
- ori r4, r4, (CFG_INIT_RAM_ADDR)@l
- li r5, 128*8 /* 128*8*32=32Kb */
- mtctr r5
-1:
- dcbz r0, r4
- addi r4, r4, 32
- bdnz 1b
- isync
-
- /* Lock all the D-cache, basically leaving the reset of the program without dcache */
- mfspr r4, HID0
- ori r4, r4, (HID0_DLOCK)@l
- sync
- mtspr HID0 , r4
-
- /* setup the stack pointer in r1 */
- lis r1, (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET)@h
- ori r1, r1, (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET)@l
- li r0, 0 /* Make room for stack frame header and */
-
- stwu r0, -4(r1) /* clear final stack frame so that */
- stwu r0, -4(r1) /* stack backtraces terminate cleanly */
-
- blr
-
-un_setup_stack_in_data_cache:
- blr
- mr r14, r4
- mr r15, r5
-
-
- lis r4, (CFG_INIT_RAM_ADDR & 0xFFFE0000)@h
- mtspr DBAT0U, r4
- ori r4, r4, 0x0002
- mtspr DBAT0L, r4
- isync
-
- /* un lock all the D-cache */
- mfspr r4, HID0
- lis r5, (~(HID0_DLOCK))@h
- ori r5, r5, (~(HID0_DLOCK))@l
- and r4, r4, r5
- sync
- mtspr HID0 , r4
-
- /* Re - Allocate Initial RAM in data cache.*/
- li r0, 0
- lis r4, (CFG_INIT_RAM_ADDR)@h
- ori r4, r4, (CFG_INIT_RAM_ADDR)@l
- li r5, 128*8 /* 128*8*32=32Kb */
- mtctr r5
-1:
- dcbz r0, r4
- addi r4, r4, 32
- bdnz 1b
- isync
-
- mflr r16
- bl dcache_disable
- mtlr r16
-
- blr
-
-#if 0
-#define GREEN_LIGHT 0x2B0D4046
-#define RED_LIGHT 0x250D4046
-#define LIB_CNT 0x4FFF
-
-/*
- * Lib Light
- */
-
- .globl liblight
-liblight:
- lis r3, CFG_IMMRBAR@h
- ori r3, r3, CFG_IMMRBAR@l
- li r4, 0x3002
- mtmsr r4
- xor r4, r4, r4
- mtspr HID0, r4
- mtspr HID2, r4
- lis r4, 0xF8000000@h
- ori r4, r4, 0xF8000000@l
- stw r4, LBLAWBAR1(r3)
- lis r4, 0x8000000E@h
- ori r4, r4, 0x8000000E@l
- stw r4, LBLAWAR1(r3)
- lis r4, 0xF8000801@h
- ori r4, r4, 0xF8000801@l
- stw r4, BR1(r3)
- lis r4, 0xFFFFE8f0@h
- ori r4, r4, 0xFFFFE8f0@l
- stw r4, OR1(r3)
-
- lis r4, 0xF8000000@h
- ori r4, r4, 0xF8000000@l
- lis r5, GREEN_LIGHT@h
- ori r5, r5, GREEN_LIGHT@l
- lis r6, RED_LIGHT@h
- ori r6, r6, RED_LIGHT@l
- lis r7, LIB_CNT@h
- ori r7, r7, LIB_CNT@l
-
-1:
- stw r5, 0(r4)
- mtctr r7
-2: bdnz 2b
- stw r6, 0(r4)
- mtctr r7
-3: bdnz 3b
- b 1b
-
-#endif
PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev));
if (cfg) {
cfg->config_device(hose, dev, cfg);
+ sub_bus = max(sub_bus, hose->current_busno);
#ifdef CONFIG_PCI_PNP
} else {
int n = pciauto_config_device(hose, dev);
void pciauto_setup_device(struct pci_controller *hose,
pci_dev_t dev, int bars_num,
struct pci_region *mem,
+ struct pci_region *prefetch,
struct pci_region *io)
{
unsigned int bar_value, bar_response, bar_size;
found_mem64 = 1;
bar_size = ~(bar_response & PCI_BASE_ADDRESS_MEM_MASK) + 1;
- bar_res = mem;
+ if (prefetch && (bar_response & PCI_BASE_ADDRESS_MEM_PREFETCH))
+ bar_res = prefetch;
+ else
+ bar_res = mem;
DEBUGF("PCI Autoconfig: BAR %d, Mem, size=0x%x, ", bar_nr, bar_size);
}
pci_dev_t dev, int sub_bus)
{
struct pci_region *pci_mem = hose->pci_mem;
+ struct pci_region *pci_prefetch = hose->pci_prefetch;
struct pci_region *pci_io = hose->pci_io;
unsigned int cmdstat;
cmdstat |= PCI_COMMAND_MEMORY;
}
+ if (pci_prefetch) {
+ /* Round memory allocator to 1MB boundary */
+ pciauto_region_align(pci_prefetch, 0x100000);
+
+ /* Set up memory and I/O filter limits, assume 32-bit I/O space */
+ pci_hose_write_config_word(hose, dev, PCI_PREF_MEMORY_BASE,
+ (pci_prefetch->bus_lower & 0xfff00000) >> 16);
+
+ cmdstat |= PCI_COMMAND_MEMORY;
+ } else {
+ /* We don't support prefetchable memory for now, so disable */
+ pci_hose_write_config_word(hose, dev, PCI_PREF_MEMORY_BASE, 0x1000);
+ pci_hose_write_config_word(hose, dev, PCI_PREF_MEMORY_LIMIT, 0x1000);
+ }
+
if (pci_io) {
/* Round I/O allocator to 4KB boundary */
pciauto_region_align(pci_io, 0x1000);
cmdstat |= PCI_COMMAND_IO;
}
- /* We don't support prefetchable memory for now, so disable */
- pci_hose_write_config_word(hose, dev, PCI_PREF_MEMORY_BASE, 0x1000);
- pci_hose_write_config_word(hose, dev, PCI_PREF_MEMORY_LIMIT, 0x1000);
-
/* Enable memory and I/O accesses, enable bus master */
pci_hose_write_config_dword(hose, dev, PCI_COMMAND, cmdstat | PCI_COMMAND_MASTER);
}
pci_dev_t dev, int sub_bus)
{
struct pci_region *pci_mem = hose->pci_mem;
+ struct pci_region *pci_prefetch = hose->pci_prefetch;
struct pci_region *pci_io = hose->pci_io;
/* Configure bus number registers */
(pci_mem->bus_lower-1) >> 16);
}
+ if (pci_prefetch) {
+ /* Round memory allocator to 1MB boundary */
+ pciauto_region_align(pci_prefetch, 0x100000);
+
+ pci_hose_write_config_word(hose, dev, PCI_PREF_MEMORY_LIMIT,
+ (pci_prefetch->bus_lower-1) >> 16);
+ }
+
if (pci_io) {
/* Round I/O allocator to 4KB boundary */
pciauto_region_align(pci_io, 0x1000);
hose->pci_mem->size < hose->regions[i].size)
hose->pci_mem = hose->regions + i;
break;
+ case (PCI_REGION_MEM | PCI_REGION_PREFETCH):
+ if (!hose->pci_prefetch ||
+ hose->pci_prefetch->size < hose->regions[i].size)
+ hose->pci_prefetch = hose->regions + i;
+ break;
}
}
hose->pci_mem->bus_start + hose->pci_mem->size - 1);
}
+ if (hose->pci_prefetch) {
+ pciauto_region_init(hose->pci_prefetch);
+
+ DEBUGF("PCI Autoconfig: Prefetchable Memory region: [%lx-%lx]\n",
+ hose->pci_prefetch->bus_start,
+ hose->pci_prefetch->bus_start + hose->pci_prefetch->size - 1);
+ }
+
if (hose->pci_io) {
pciauto_region_init(hose->pci_io);
switch(class) {
case PCI_CLASS_BRIDGE_PCI:
hose->current_busno++;
- pciauto_setup_device(hose, dev, 2, hose->pci_mem, hose->pci_io);
+ pciauto_setup_device(hose, dev, 2, hose->pci_mem, hose->pci_prefetch, hose->pci_io);
DEBUGF("PCI Autoconfig: Found P2P bridge, device %d\n", PCI_DEV(dev));
return sub_bus;
}
- pciauto_setup_device(hose, dev, 6, hose->pci_mem, hose->pci_io);
+ pciauto_setup_device(hose, dev, 6, hose->pci_mem, hose->pci_prefetch, hose->pci_io);
break;
case PCI_CLASS_BRIDGE_CARDBUS:
/* just do a minimal setup of the bridge, let the OS take care of the rest */
- pciauto_setup_device(hose, dev, 0, hose->pci_mem, hose->pci_io);
+ pciauto_setup_device(hose, dev, 0, hose->pci_mem, hose->pci_prefetch, hose->pci_io);
DEBUGF("PCI Autoconfig: Found P2CardBus bridge, device %d\n", PCI_DEV(dev));
* the PIMMR window to be allocated (BAR0 - 1MB size)
*/
DEBUGF("PCI Autoconfig: Broken bridge found, only minimal config\n");
- pciauto_setup_device(hose, dev, 0, hose->pci_mem, hose->pci_io);
+ pciauto_setup_device(hose, dev, 0, hose->pci_mem, hose->pci_prefetch, hose->pci_io);
break;
#endif
default:
- pciauto_setup_device(hose, dev, 6, hose->pci_mem, hose->pci_io);
+ pciauto_setup_device(hose, dev, 6, hose->pci_mem, hose->pci_prefetch, hose->pci_io);
break;
}
indirect_##rw##_config_##size(struct pci_controller *hose, \
pci_dev_t dev, int offset, type val) \
{ \
+ u32 b, d,f; \
+ b = PCI_BUS(dev); d = PCI_DEV(dev); f = PCI_FUNC(dev); \
+ b = b - hose->first_busno; \
+ dev = PCI_BDF(b, d, f); \
out_le32(hose->cfg_addr, dev | (offset & 0xfc) | 0x80000000); \
sync(); \
cfg_##rw(val, hose->cfg_data + (offset & mask), type, op); \
indirect_##rw##_config_##size(struct pci_controller *hose, \
pci_dev_t dev, int offset, type val) \
{ \
+ u32 b, d,f; \
+ b = PCI_BUS(dev); d = PCI_DEV(dev); f = PCI_FUNC(dev); \
+ b = b - hose->first_busno; \
+ dev = PCI_BDF(b, d, f); \
*(hose->cfg_addr) = dev | (offset & 0xfc) | 0x80000000; \
sync(); \
cfg_##rw(val, hose->cfg_data + (offset & mask), type, op); \
indirect_##rw##_config_##size(struct pci_controller *hose, \
pci_dev_t dev, int offset, type val) \
{ \
+ u32 b, d,f; \
+ b = PCI_BUS(dev); d = PCI_DEV(dev); f = PCI_FUNC(dev); \
+ b = b - hose->first_busno; \
+ dev = PCI_BDF(b, d, f); \
if (PCI_BUS(dev) > 0) \
out_le32(hose->cfg_addr, dev | (offset & 0xfc) | 0x80000001); \
else \
indirect_##rw##_config_##size(struct pci_controller *hose, \
pci_dev_t dev, int offset, type val) \
{ \
+ u32 b, d,f; \
+ b = PCI_BUS(dev); d = PCI_DEV(dev); f = PCI_FUNC(dev); \
+ b = b - hose->first_busno; \
+ dev = PCI_BDF(b, d, f); \
out_le32(hose->cfg_addr, dev | (offset & 0xfc) | 0x80000000); \
cfg_##rw(val, hose->cfg_data + (offset & mask), type, op); \
return 0; \
| SPCR_TSEC2DP | SPCR_TSEC2BDP | SPCR_TSEC2EP)
u32 sicrl; /* System General Purpose Register Low */
#define SICRL_LDP_A 0x80000000
-#define SICRL_USB0 0x40000000
-#define SICRL_USB1 0x20000000
+#define SICRL_USB1 0x40000000
+#define SICRL_USB0 0x20000000
#define SICRL_UART 0x0C000000
#define SICRL_GPIO1_A 0x02000000
#define SICRL_GPIO1_B 0x01000000
#define POCMR_ENABLE 0x80000000
#define POCMR_PCI_IO 0x40000000
#define POCMR_PREFETCH_EN 0x20000000
+#define POCMR_PCI2 0x10000000
/* Soft PCI reset */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_MPC8349ADS 1 /* MPC8349ADS board specific */
-/* FIXME: Real PCI support will come in a follow-up update. */
-#undef CONFIG_PCI
-
+#define CONFIG_PCI
+#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
* General PCI
* Addresses are mapped 1-1.
*/
+
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_MMIO_BASE 0x90000000
+#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
-#define CFG_PCI2_MEM_BASE 0xA0000000
+#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_MMIO_BASE 0xb0000000
+#define CFG_PCI2_MMIO_PHYS CFG_PCI2_MMIO_BASE
+#define CFG_PCI2_MMIO_SIZE 0x10000000 /* 256M */
#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe3000000
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI2_IO_PHYS 0xe2100000
+#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define PCI_ALL_PCI1
HRCWH_TSEC2M_IN_GMII )
#endif
+/* System IO Config */
+#define CFG_SICRH SICRH_TSOBI1
+#define CFG_SICRL SICRL_LDP_A
+
#define CFG_HID0_INIT 0x000000000
#define CFG_HID0_FINAL CFG_HID0_INIT
HID0_ENABLE_M_BIT |\
HID0_ENABLE_ADDRESS_BROADCAST ) */
-#define CFG_HID2 0x000000000
+#define CFG_HID2 HID2_HBE
+
+/* DDR 0 - 256MB */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* stack in DCACHE @ 1GB (no backing mem) */
+#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+
+/* 2G - 3G PCI */
+#ifdef CONFIG_PCI
+#define CFG_IBAT2L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT2U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT3L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT3U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT2L (0)
+#define CFG_IBAT2U (0)
+#define CFG_IBAT3L (0)
+#define CFG_IBAT3U (0)
+#endif
+
+#ifdef CONFIG_MPC83XX_PCI2
+#define CFG_IBAT4L (CFG_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT4U (CFG_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT5L (CFG_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT4L (0)
+#define CFG_IBAT4U (0)
+#define CFG_IBAT5L (0)
+#define CFG_IBAT5U (0)
+#endif
+
+/* IMMRBAR */
+#define CFG_IBAT6L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT6U (CFG_IMMRBAR | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* SDRAM, BCSR & FLASH */
+#define CFG_IBAT7L (0xf0000000 | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT7U (0xf0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+
/*
* Internal Definitions
HRCWH_TSEC2M_IN_GMII )
#endif
+/* System IO Config */
+#define CFG_SICRH SICRH_TSOBI1
+#define CFG_SICRL SICRL_LDP_A
+
/* i-cache and d-cache disabled */
#define CFG_HID0_INIT 0x000000000
#define CFG_HID0_FINAL CFG_HID0_INIT
#define CFG_HID2 0x000000000
+/* DDR 0 - 512M */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT1L (CFG_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_SDRAM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* stack in DCACHE @ 512M (no backing mem) */
+#define CFG_IBAT2L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT2U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+
+/* PCI */
+#define CFG_IBAT3L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT3U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI1_MEM_BASE + 0x10000000 | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT4U (CFG_PCI1_MEM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT5L (CFG_PCI1_IO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_PCI1_IO_BASE + 0x10000000 | BATU_BL_16M | BATU_VS | BATU_VP)
+
+/* IMMRBAR */
+#define CFG_IBAT6L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT6U (CFG_IMMRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
+
+/* FLASH */
+#define CFG_IBAT7L (CFG_FLASH_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT7U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+
/*
* Internal Definitions
*
#define OF_CPU "PowerPC,MPC870@0"
#define OF_TBCLK (MPC8XX_HZ / 16)
+#define CONFIG_OF_HAS_BD_T 1
+#define CONFIG_OF_HAS_UBOOT_ENV 1
#endif /* __CONFIG_H */
void ft_begin(struct ft_cxt *cxt, void *blob, int max_size);
void ft_add_rsvmap(struct ft_cxt *cxt, u64 physaddr, u64 size);
-void ft_setup(void *blob, int size, bd_t * bd);
+void ft_setup(void *blob, int size, bd_t * bd, ulong initrd_start, ulong initrd_end);
void ft_dump_blob(const void *bphp);
void ft_merge_blob(struct ft_cxt *cxt, void *blob);
void *ft_get_prop(void *bphp, const char *propname, int *szp);
+void ft_board_setup(void *blob, bd_t *bd);
+
#endif
#define PCI_REGION_MEM 0x00000000 /* PCI memory space */
#define PCI_REGION_IO 0x00000001 /* PCI IO space */
#define PCI_REGION_TYPE 0x00000001
+#define PCI_REGION_PREFETCH 0x00000008 /* prefetchable PCI memory */
#define PCI_REGION_MEMORY 0x00000100 /* System memory */
#define PCI_REGION_RO 0x00000200 /* Read-only memory */
int (*write_dword)(struct pci_controller*, pci_dev_t, int where, u32);
/* Used by auto config */
- struct pci_region *pci_mem, *pci_io;
+ struct pci_region *pci_mem, *pci_io, *pci_prefetch;
/* Used by ppc405 autoconfig*/
struct pci_region *pci_fb;
extern void pciauto_setup_device(struct pci_controller *hose,
pci_dev_t dev, int bars_num,
struct pci_region *mem,
+ struct pci_region *prefetch,
struct pci_region *io);
int pciauto_config_device(struct pci_controller *hose, pci_dev_t dev);
WATCHDOG_RESET();
-#if defined(CONFIG_IP860) || defined(CONFIG_PCU_E) || defined (CONFIG_FLAGADM)
+#if defined(CONFIG_IP860) || defined(CONFIG_PCU_E) || \
+ defined (CONFIG_FLAGADM) || defined(CONFIG_MPC83XX)
icache_enable (); /* it's time to enable the instruction cache */
#endif
projects / platform / kernel / u-boot.git / commitdiff