This patch adds support for the atusb transceiver.
The current driver supports basic functionality only. Possible further
tasks would be to sync functionality with the at86rf230 driver, because
the atusb use internally an at86rf231 transceiver. Some of these
features need a firmware update like AACK and ARET handling.
I did small changes to this driver to work with xmit_async callback and
setting of a random extended perm address.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Werner Almesberger <werner@almesberger.net>
Cc: Stefan Schmidt <s.schmidt@samsung.com>
Cc: Richard Sharpe <realrichardsharpe@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver can also be built as a module. To do so, say M here.
the module will be called 'cc2520'.
+
+config IEEE802154_ATUSB
+ tristate "ATUSB transceiver driver"
+ depends on IEEE802154_DRIVERS && MAC802154 && USB
+ ---help---
+ Say Y here to enable the ATUSB IEEE 802.15.4 wireless
+ controller.
+
+ This driver can also be built as a module. To do so say M here.
+ The module will be called 'atusb'.
obj-$(CONFIG_IEEE802154_AT86RF230) += at86rf230.o
obj-$(CONFIG_IEEE802154_MRF24J40) += mrf24j40.o
obj-$(CONFIG_IEEE802154_CC2520) += cc2520.o
+obj-$(CONFIG_IEEE802154_ATUSB) += atusb.o
#include <net/mac802154.h>
#include <net/cfg802154.h>
+#include "at86rf230.h"
+
struct at86rf230_local;
/* at86rf2xx chip depend data.
* All timings are in us.
struct at86rf230_state_change tx;
};
-#define RG_TRX_STATUS (0x01)
-#define SR_TRX_STATUS 0x01, 0x1f, 0
-#define SR_RESERVED_01_3 0x01, 0x20, 5
-#define SR_CCA_STATUS 0x01, 0x40, 6
-#define SR_CCA_DONE 0x01, 0x80, 7
-#define RG_TRX_STATE (0x02)
-#define SR_TRX_CMD 0x02, 0x1f, 0
-#define SR_TRAC_STATUS 0x02, 0xe0, 5
-#define RG_TRX_CTRL_0 (0x03)
-#define SR_CLKM_CTRL 0x03, 0x07, 0
-#define SR_CLKM_SHA_SEL 0x03, 0x08, 3
-#define SR_PAD_IO_CLKM 0x03, 0x30, 4
-#define SR_PAD_IO 0x03, 0xc0, 6
-#define RG_TRX_CTRL_1 (0x04)
-#define SR_IRQ_POLARITY 0x04, 0x01, 0
-#define SR_IRQ_MASK_MODE 0x04, 0x02, 1
-#define SR_SPI_CMD_MODE 0x04, 0x0c, 2
-#define SR_RX_BL_CTRL 0x04, 0x10, 4
-#define SR_TX_AUTO_CRC_ON 0x04, 0x20, 5
-#define SR_IRQ_2_EXT_EN 0x04, 0x40, 6
-#define SR_PA_EXT_EN 0x04, 0x80, 7
-#define RG_PHY_TX_PWR (0x05)
-#define SR_TX_PWR_23X 0x05, 0x0f, 0
-#define SR_PA_LT_230 0x05, 0x30, 4
-#define SR_PA_BUF_LT_230 0x05, 0xc0, 6
-#define SR_TX_PWR_212 0x05, 0x1f, 0
-#define SR_GC_PA_212 0x05, 0x60, 5
-#define SR_PA_BOOST_LT_212 0x05, 0x80, 7
-#define RG_PHY_RSSI (0x06)
-#define SR_RSSI 0x06, 0x1f, 0
-#define SR_RND_VALUE 0x06, 0x60, 5
-#define SR_RX_CRC_VALID 0x06, 0x80, 7
-#define RG_PHY_ED_LEVEL (0x07)
-#define SR_ED_LEVEL 0x07, 0xff, 0
-#define RG_PHY_CC_CCA (0x08)
-#define SR_CHANNEL 0x08, 0x1f, 0
-#define SR_CCA_MODE 0x08, 0x60, 5
-#define SR_CCA_REQUEST 0x08, 0x80, 7
-#define RG_CCA_THRES (0x09)
-#define SR_CCA_ED_THRES 0x09, 0x0f, 0
-#define SR_RESERVED_09_1 0x09, 0xf0, 4
-#define RG_RX_CTRL (0x0a)
-#define SR_PDT_THRES 0x0a, 0x0f, 0
-#define SR_RESERVED_0a_1 0x0a, 0xf0, 4
-#define RG_SFD_VALUE (0x0b)
-#define SR_SFD_VALUE 0x0b, 0xff, 0
-#define RG_TRX_CTRL_2 (0x0c)
-#define SR_OQPSK_DATA_RATE 0x0c, 0x03, 0
-#define SR_SUB_MODE 0x0c, 0x04, 2
-#define SR_BPSK_QPSK 0x0c, 0x08, 3
-#define SR_OQPSK_SUB1_RC_EN 0x0c, 0x10, 4
-#define SR_RESERVED_0c_5 0x0c, 0x60, 5
-#define SR_RX_SAFE_MODE 0x0c, 0x80, 7
-#define RG_ANT_DIV (0x0d)
-#define SR_ANT_CTRL 0x0d, 0x03, 0
-#define SR_ANT_EXT_SW_EN 0x0d, 0x04, 2
-#define SR_ANT_DIV_EN 0x0d, 0x08, 3
-#define SR_RESERVED_0d_2 0x0d, 0x70, 4
-#define SR_ANT_SEL 0x0d, 0x80, 7
-#define RG_IRQ_MASK (0x0e)
-#define SR_IRQ_MASK 0x0e, 0xff, 0
-#define RG_IRQ_STATUS (0x0f)
-#define SR_IRQ_0_PLL_LOCK 0x0f, 0x01, 0
-#define SR_IRQ_1_PLL_UNLOCK 0x0f, 0x02, 1
-#define SR_IRQ_2_RX_START 0x0f, 0x04, 2
-#define SR_IRQ_3_TRX_END 0x0f, 0x08, 3
-#define SR_IRQ_4_CCA_ED_DONE 0x0f, 0x10, 4
-#define SR_IRQ_5_AMI 0x0f, 0x20, 5
-#define SR_IRQ_6_TRX_UR 0x0f, 0x40, 6
-#define SR_IRQ_7_BAT_LOW 0x0f, 0x80, 7
-#define RG_VREG_CTRL (0x10)
-#define SR_RESERVED_10_6 0x10, 0x03, 0
-#define SR_DVDD_OK 0x10, 0x04, 2
-#define SR_DVREG_EXT 0x10, 0x08, 3
-#define SR_RESERVED_10_3 0x10, 0x30, 4
-#define SR_AVDD_OK 0x10, 0x40, 6
-#define SR_AVREG_EXT 0x10, 0x80, 7
-#define RG_BATMON (0x11)
-#define SR_BATMON_VTH 0x11, 0x0f, 0
-#define SR_BATMON_HR 0x11, 0x10, 4
-#define SR_BATMON_OK 0x11, 0x20, 5
-#define SR_RESERVED_11_1 0x11, 0xc0, 6
-#define RG_XOSC_CTRL (0x12)
-#define SR_XTAL_TRIM 0x12, 0x0f, 0
-#define SR_XTAL_MODE 0x12, 0xf0, 4
-#define RG_RX_SYN (0x15)
-#define SR_RX_PDT_LEVEL 0x15, 0x0f, 0
-#define SR_RESERVED_15_2 0x15, 0x70, 4
-#define SR_RX_PDT_DIS 0x15, 0x80, 7
-#define RG_XAH_CTRL_1 (0x17)
-#define SR_RESERVED_17_8 0x17, 0x01, 0
-#define SR_AACK_PROM_MODE 0x17, 0x02, 1
-#define SR_AACK_ACK_TIME 0x17, 0x04, 2
-#define SR_RESERVED_17_5 0x17, 0x08, 3
-#define SR_AACK_UPLD_RES_FT 0x17, 0x10, 4
-#define SR_AACK_FLTR_RES_FT 0x17, 0x20, 5
-#define SR_CSMA_LBT_MODE 0x17, 0x40, 6
-#define SR_RESERVED_17_1 0x17, 0x80, 7
-#define RG_FTN_CTRL (0x18)
-#define SR_RESERVED_18_2 0x18, 0x7f, 0
-#define SR_FTN_START 0x18, 0x80, 7
-#define RG_PLL_CF (0x1a)
-#define SR_RESERVED_1a_2 0x1a, 0x7f, 0
-#define SR_PLL_CF_START 0x1a, 0x80, 7
-#define RG_PLL_DCU (0x1b)
-#define SR_RESERVED_1b_3 0x1b, 0x3f, 0
-#define SR_RESERVED_1b_2 0x1b, 0x40, 6
-#define SR_PLL_DCU_START 0x1b, 0x80, 7
-#define RG_PART_NUM (0x1c)
-#define SR_PART_NUM 0x1c, 0xff, 0
-#define RG_VERSION_NUM (0x1d)
-#define SR_VERSION_NUM 0x1d, 0xff, 0
-#define RG_MAN_ID_0 (0x1e)
-#define SR_MAN_ID_0 0x1e, 0xff, 0
-#define RG_MAN_ID_1 (0x1f)
-#define SR_MAN_ID_1 0x1f, 0xff, 0
-#define RG_SHORT_ADDR_0 (0x20)
-#define SR_SHORT_ADDR_0 0x20, 0xff, 0
-#define RG_SHORT_ADDR_1 (0x21)
-#define SR_SHORT_ADDR_1 0x21, 0xff, 0
-#define RG_PAN_ID_0 (0x22)
-#define SR_PAN_ID_0 0x22, 0xff, 0
-#define RG_PAN_ID_1 (0x23)
-#define SR_PAN_ID_1 0x23, 0xff, 0
-#define RG_IEEE_ADDR_0 (0x24)
-#define SR_IEEE_ADDR_0 0x24, 0xff, 0
-#define RG_IEEE_ADDR_1 (0x25)
-#define SR_IEEE_ADDR_1 0x25, 0xff, 0
-#define RG_IEEE_ADDR_2 (0x26)
-#define SR_IEEE_ADDR_2 0x26, 0xff, 0
-#define RG_IEEE_ADDR_3 (0x27)
-#define SR_IEEE_ADDR_3 0x27, 0xff, 0
-#define RG_IEEE_ADDR_4 (0x28)
-#define SR_IEEE_ADDR_4 0x28, 0xff, 0
-#define RG_IEEE_ADDR_5 (0x29)
-#define SR_IEEE_ADDR_5 0x29, 0xff, 0
-#define RG_IEEE_ADDR_6 (0x2a)
-#define SR_IEEE_ADDR_6 0x2a, 0xff, 0
-#define RG_IEEE_ADDR_7 (0x2b)
-#define SR_IEEE_ADDR_7 0x2b, 0xff, 0
-#define RG_XAH_CTRL_0 (0x2c)
-#define SR_SLOTTED_OPERATION 0x2c, 0x01, 0
-#define SR_MAX_CSMA_RETRIES 0x2c, 0x0e, 1
-#define SR_MAX_FRAME_RETRIES 0x2c, 0xf0, 4
-#define RG_CSMA_SEED_0 (0x2d)
-#define SR_CSMA_SEED_0 0x2d, 0xff, 0
-#define RG_CSMA_SEED_1 (0x2e)
-#define SR_CSMA_SEED_1 0x2e, 0x07, 0
-#define SR_AACK_I_AM_COORD 0x2e, 0x08, 3
-#define SR_AACK_DIS_ACK 0x2e, 0x10, 4
-#define SR_AACK_SET_PD 0x2e, 0x20, 5
-#define SR_AACK_FVN_MODE 0x2e, 0xc0, 6
-#define RG_CSMA_BE (0x2f)
-#define SR_MIN_BE 0x2f, 0x0f, 0
-#define SR_MAX_BE 0x2f, 0xf0, 4
-
-#define CMD_REG 0x80
-#define CMD_REG_MASK 0x3f
-#define CMD_WRITE 0x40
-#define CMD_FB 0x20
-
-#define IRQ_BAT_LOW (1 << 7)
-#define IRQ_TRX_UR (1 << 6)
-#define IRQ_AMI (1 << 5)
-#define IRQ_CCA_ED (1 << 4)
-#define IRQ_TRX_END (1 << 3)
-#define IRQ_RX_START (1 << 2)
-#define IRQ_PLL_UNL (1 << 1)
-#define IRQ_PLL_LOCK (1 << 0)
-
-#define IRQ_ACTIVE_HIGH 0
-#define IRQ_ACTIVE_LOW 1
-
-#define STATE_P_ON 0x00 /* BUSY */
-#define STATE_BUSY_RX 0x01
-#define STATE_BUSY_TX 0x02
-#define STATE_FORCE_TRX_OFF 0x03
-#define STATE_FORCE_TX_ON 0x04 /* IDLE */
-/* 0x05 */ /* INVALID_PARAMETER */
-#define STATE_RX_ON 0x06
-/* 0x07 */ /* SUCCESS */
-#define STATE_TRX_OFF 0x08
-#define STATE_TX_ON 0x09
-/* 0x0a - 0x0e */ /* 0x0a - UNSUPPORTED_ATTRIBUTE */
-#define STATE_SLEEP 0x0F
-#define STATE_PREP_DEEP_SLEEP 0x10
-#define STATE_BUSY_RX_AACK 0x11
-#define STATE_BUSY_TX_ARET 0x12
-#define STATE_RX_AACK_ON 0x16
-#define STATE_TX_ARET_ON 0x19
-#define STATE_RX_ON_NOCLK 0x1C
-#define STATE_RX_AACK_ON_NOCLK 0x1D
-#define STATE_BUSY_RX_AACK_NOCLK 0x1E
-#define STATE_TRANSITION_IN_PROGRESS 0x1F
-
-#define TRX_STATE_MASK (0x1F)
-
#define AT86RF2XX_NUMREGS 0x3F
static void
--- /dev/null
+/*
+ * AT86RF230/RF231 driver
+ *
+ * Copyright (C) 2009-2012 Siemens AG
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Written by:
+ * Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
+ * Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
+ */
+
+#ifndef _AT86RF230_H
+#define _AT86RF230_H
+
+#define RG_TRX_STATUS (0x01)
+#define SR_TRX_STATUS 0x01, 0x1f, 0
+#define SR_RESERVED_01_3 0x01, 0x20, 5
+#define SR_CCA_STATUS 0x01, 0x40, 6
+#define SR_CCA_DONE 0x01, 0x80, 7
+#define RG_TRX_STATE (0x02)
+#define SR_TRX_CMD 0x02, 0x1f, 0
+#define SR_TRAC_STATUS 0x02, 0xe0, 5
+#define RG_TRX_CTRL_0 (0x03)
+#define SR_CLKM_CTRL 0x03, 0x07, 0
+#define SR_CLKM_SHA_SEL 0x03, 0x08, 3
+#define SR_PAD_IO_CLKM 0x03, 0x30, 4
+#define SR_PAD_IO 0x03, 0xc0, 6
+#define RG_TRX_CTRL_1 (0x04)
+#define SR_IRQ_POLARITY 0x04, 0x01, 0
+#define SR_IRQ_MASK_MODE 0x04, 0x02, 1
+#define SR_SPI_CMD_MODE 0x04, 0x0c, 2
+#define SR_RX_BL_CTRL 0x04, 0x10, 4
+#define SR_TX_AUTO_CRC_ON 0x04, 0x20, 5
+#define SR_IRQ_2_EXT_EN 0x04, 0x40, 6
+#define SR_PA_EXT_EN 0x04, 0x80, 7
+#define RG_PHY_TX_PWR (0x05)
+#define SR_TX_PWR_23X 0x05, 0x0f, 0
+#define SR_PA_LT_230 0x05, 0x30, 4
+#define SR_PA_BUF_LT_230 0x05, 0xc0, 6
+#define SR_TX_PWR_212 0x05, 0x1f, 0
+#define SR_GC_PA_212 0x05, 0x60, 5
+#define SR_PA_BOOST_LT_212 0x05, 0x80, 7
+#define RG_PHY_RSSI (0x06)
+#define SR_RSSI 0x06, 0x1f, 0
+#define SR_RND_VALUE 0x06, 0x60, 5
+#define SR_RX_CRC_VALID 0x06, 0x80, 7
+#define RG_PHY_ED_LEVEL (0x07)
+#define SR_ED_LEVEL 0x07, 0xff, 0
+#define RG_PHY_CC_CCA (0x08)
+#define SR_CHANNEL 0x08, 0x1f, 0
+#define SR_CCA_MODE 0x08, 0x60, 5
+#define SR_CCA_REQUEST 0x08, 0x80, 7
+#define RG_CCA_THRES (0x09)
+#define SR_CCA_ED_THRES 0x09, 0x0f, 0
+#define SR_RESERVED_09_1 0x09, 0xf0, 4
+#define RG_RX_CTRL (0x0a)
+#define SR_PDT_THRES 0x0a, 0x0f, 0
+#define SR_RESERVED_0a_1 0x0a, 0xf0, 4
+#define RG_SFD_VALUE (0x0b)
+#define SR_SFD_VALUE 0x0b, 0xff, 0
+#define RG_TRX_CTRL_2 (0x0c)
+#define SR_OQPSK_DATA_RATE 0x0c, 0x03, 0
+#define SR_SUB_MODE 0x0c, 0x04, 2
+#define SR_BPSK_QPSK 0x0c, 0x08, 3
+#define SR_OQPSK_SUB1_RC_EN 0x0c, 0x10, 4
+#define SR_RESERVED_0c_5 0x0c, 0x60, 5
+#define SR_RX_SAFE_MODE 0x0c, 0x80, 7
+#define RG_ANT_DIV (0x0d)
+#define SR_ANT_CTRL 0x0d, 0x03, 0
+#define SR_ANT_EXT_SW_EN 0x0d, 0x04, 2
+#define SR_ANT_DIV_EN 0x0d, 0x08, 3
+#define SR_RESERVED_0d_2 0x0d, 0x70, 4
+#define SR_ANT_SEL 0x0d, 0x80, 7
+#define RG_IRQ_MASK (0x0e)
+#define SR_IRQ_MASK 0x0e, 0xff, 0
+#define RG_IRQ_STATUS (0x0f)
+#define SR_IRQ_0_PLL_LOCK 0x0f, 0x01, 0
+#define SR_IRQ_1_PLL_UNLOCK 0x0f, 0x02, 1
+#define SR_IRQ_2_RX_START 0x0f, 0x04, 2
+#define SR_IRQ_3_TRX_END 0x0f, 0x08, 3
+#define SR_IRQ_4_CCA_ED_DONE 0x0f, 0x10, 4
+#define SR_IRQ_5_AMI 0x0f, 0x20, 5
+#define SR_IRQ_6_TRX_UR 0x0f, 0x40, 6
+#define SR_IRQ_7_BAT_LOW 0x0f, 0x80, 7
+#define RG_VREG_CTRL (0x10)
+#define SR_RESERVED_10_6 0x10, 0x03, 0
+#define SR_DVDD_OK 0x10, 0x04, 2
+#define SR_DVREG_EXT 0x10, 0x08, 3
+#define SR_RESERVED_10_3 0x10, 0x30, 4
+#define SR_AVDD_OK 0x10, 0x40, 6
+#define SR_AVREG_EXT 0x10, 0x80, 7
+#define RG_BATMON (0x11)
+#define SR_BATMON_VTH 0x11, 0x0f, 0
+#define SR_BATMON_HR 0x11, 0x10, 4
+#define SR_BATMON_OK 0x11, 0x20, 5
+#define SR_RESERVED_11_1 0x11, 0xc0, 6
+#define RG_XOSC_CTRL (0x12)
+#define SR_XTAL_TRIM 0x12, 0x0f, 0
+#define SR_XTAL_MODE 0x12, 0xf0, 4
+#define RG_RX_SYN (0x15)
+#define SR_RX_PDT_LEVEL 0x15, 0x0f, 0
+#define SR_RESERVED_15_2 0x15, 0x70, 4
+#define SR_RX_PDT_DIS 0x15, 0x80, 7
+#define RG_XAH_CTRL_1 (0x17)
+#define SR_RESERVED_17_8 0x17, 0x01, 0
+#define SR_AACK_PROM_MODE 0x17, 0x02, 1
+#define SR_AACK_ACK_TIME 0x17, 0x04, 2
+#define SR_RESERVED_17_5 0x17, 0x08, 3
+#define SR_AACK_UPLD_RES_FT 0x17, 0x10, 4
+#define SR_AACK_FLTR_RES_FT 0x17, 0x20, 5
+#define SR_CSMA_LBT_MODE 0x17, 0x40, 6
+#define SR_RESERVED_17_1 0x17, 0x80, 7
+#define RG_FTN_CTRL (0x18)
+#define SR_RESERVED_18_2 0x18, 0x7f, 0
+#define SR_FTN_START 0x18, 0x80, 7
+#define RG_PLL_CF (0x1a)
+#define SR_RESERVED_1a_2 0x1a, 0x7f, 0
+#define SR_PLL_CF_START 0x1a, 0x80, 7
+#define RG_PLL_DCU (0x1b)
+#define SR_RESERVED_1b_3 0x1b, 0x3f, 0
+#define SR_RESERVED_1b_2 0x1b, 0x40, 6
+#define SR_PLL_DCU_START 0x1b, 0x80, 7
+#define RG_PART_NUM (0x1c)
+#define SR_PART_NUM 0x1c, 0xff, 0
+#define RG_VERSION_NUM (0x1d)
+#define SR_VERSION_NUM 0x1d, 0xff, 0
+#define RG_MAN_ID_0 (0x1e)
+#define SR_MAN_ID_0 0x1e, 0xff, 0
+#define RG_MAN_ID_1 (0x1f)
+#define SR_MAN_ID_1 0x1f, 0xff, 0
+#define RG_SHORT_ADDR_0 (0x20)
+#define SR_SHORT_ADDR_0 0x20, 0xff, 0
+#define RG_SHORT_ADDR_1 (0x21)
+#define SR_SHORT_ADDR_1 0x21, 0xff, 0
+#define RG_PAN_ID_0 (0x22)
+#define SR_PAN_ID_0 0x22, 0xff, 0
+#define RG_PAN_ID_1 (0x23)
+#define SR_PAN_ID_1 0x23, 0xff, 0
+#define RG_IEEE_ADDR_0 (0x24)
+#define SR_IEEE_ADDR_0 0x24, 0xff, 0
+#define RG_IEEE_ADDR_1 (0x25)
+#define SR_IEEE_ADDR_1 0x25, 0xff, 0
+#define RG_IEEE_ADDR_2 (0x26)
+#define SR_IEEE_ADDR_2 0x26, 0xff, 0
+#define RG_IEEE_ADDR_3 (0x27)
+#define SR_IEEE_ADDR_3 0x27, 0xff, 0
+#define RG_IEEE_ADDR_4 (0x28)
+#define SR_IEEE_ADDR_4 0x28, 0xff, 0
+#define RG_IEEE_ADDR_5 (0x29)
+#define SR_IEEE_ADDR_5 0x29, 0xff, 0
+#define RG_IEEE_ADDR_6 (0x2a)
+#define SR_IEEE_ADDR_6 0x2a, 0xff, 0
+#define RG_IEEE_ADDR_7 (0x2b)
+#define SR_IEEE_ADDR_7 0x2b, 0xff, 0
+#define RG_XAH_CTRL_0 (0x2c)
+#define SR_SLOTTED_OPERATION 0x2c, 0x01, 0
+#define SR_MAX_CSMA_RETRIES 0x2c, 0x0e, 1
+#define SR_MAX_FRAME_RETRIES 0x2c, 0xf0, 4
+#define RG_CSMA_SEED_0 (0x2d)
+#define SR_CSMA_SEED_0 0x2d, 0xff, 0
+#define RG_CSMA_SEED_1 (0x2e)
+#define SR_CSMA_SEED_1 0x2e, 0x07, 0
+#define SR_AACK_I_AM_COORD 0x2e, 0x08, 3
+#define SR_AACK_DIS_ACK 0x2e, 0x10, 4
+#define SR_AACK_SET_PD 0x2e, 0x20, 5
+#define SR_AACK_FVN_MODE 0x2e, 0xc0, 6
+#define RG_CSMA_BE (0x2f)
+#define SR_MIN_BE 0x2f, 0x0f, 0
+#define SR_MAX_BE 0x2f, 0xf0, 4
+
+#define CMD_REG 0x80
+#define CMD_REG_MASK 0x3f
+#define CMD_WRITE 0x40
+#define CMD_FB 0x20
+
+#define IRQ_BAT_LOW BIT(7)
+#define IRQ_TRX_UR BIT(6)
+#define IRQ_AMI BIT(5)
+#define IRQ_CCA_ED BIT(4)
+#define IRQ_TRX_END BIT(3)
+#define IRQ_RX_START BIT(2)
+#define IRQ_PLL_UNL BIT(1)
+#define IRQ_PLL_LOCK BIT(0)
+
+#define IRQ_ACTIVE_HIGH 0
+#define IRQ_ACTIVE_LOW 1
+
+#define STATE_P_ON 0x00 /* BUSY */
+#define STATE_BUSY_RX 0x01
+#define STATE_BUSY_TX 0x02
+#define STATE_FORCE_TRX_OFF 0x03
+#define STATE_FORCE_TX_ON 0x04 /* IDLE */
+/* 0x05 */ /* INVALID_PARAMETER */
+#define STATE_RX_ON 0x06
+/* 0x07 */ /* SUCCESS */
+#define STATE_TRX_OFF 0x08
+#define STATE_TX_ON 0x09
+/* 0x0a - 0x0e */ /* 0x0a - UNSUPPORTED_ATTRIBUTE */
+#define STATE_SLEEP 0x0F
+#define STATE_PREP_DEEP_SLEEP 0x10
+#define STATE_BUSY_RX_AACK 0x11
+#define STATE_BUSY_TX_ARET 0x12
+#define STATE_RX_AACK_ON 0x16
+#define STATE_TX_ARET_ON 0x19
+#define STATE_RX_ON_NOCLK 0x1C
+#define STATE_RX_AACK_ON_NOCLK 0x1D
+#define STATE_BUSY_RX_AACK_NOCLK 0x1E
+#define STATE_TRANSITION_IN_PROGRESS 0x1F
+
+#define TRX_STATE_MASK (0x1F)
+
+#endif /* !_AT86RF230_H */
--- /dev/null
+/*
+ * atusb.c - Driver for the ATUSB IEEE 802.15.4 dongle
+ *
+ * Written 2013 by Werner Almesberger <werner@almesberger.net>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2
+ *
+ * Based on at86rf230.c and spi_atusb.c.
+ * at86rf230.c is
+ * Copyright (C) 2009 Siemens AG
+ * Written by: Dmitry Eremin-Solenikov <dmitry.baryshkov@siemens.com>
+ *
+ * spi_atusb.c is
+ * Copyright (c) 2011 Richard Sharpe <realrichardsharpe@gmail.com>
+ * Copyright (c) 2011 Stefan Schmidt <stefan@datenfreihafen.org>
+ * Copyright (c) 2011 Werner Almesberger <werner@almesberger.net>
+ *
+ * USB initialization is
+ * Copyright (c) 2013 Alexander Aring <alex.aring@gmail.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/jiffies.h>
+#include <linux/usb.h>
+#include <linux/skbuff.h>
+
+#include <net/cfg802154.h>
+#include <net/mac802154.h>
+
+#include "at86rf230.h"
+#include "atusb.h"
+
+#define ATUSB_JEDEC_ATMEL 0x1f /* JEDEC manufacturer ID */
+
+#define ATUSB_NUM_RX_URBS 4 /* allow for a bit of local latency */
+#define ATUSB_ALLOC_DELAY_MS 100 /* delay after failed allocation */
+#define ATUSB_TX_TIMEOUT_MS 200 /* on the air timeout */
+
+struct atusb {
+ struct ieee802154_hw *hw;
+ struct usb_device *usb_dev;
+ int shutdown; /* non-zero if shutting down */
+ int err; /* set by first error */
+
+ /* RX variables */
+ struct delayed_work work; /* memory allocations */
+ struct usb_anchor idle_urbs; /* URBs waiting to be submitted */
+ struct usb_anchor rx_urbs; /* URBs waiting for reception */
+
+ /* TX variables */
+ struct usb_ctrlrequest tx_dr;
+ struct urb *tx_urb;
+ struct sk_buff *tx_skb;
+ uint8_t tx_ack_seq; /* current TX ACK sequence number */
+};
+
+/* at86rf230.h defines values as <reg, mask, shift> tuples. We use the more
+ * traditional style of having registers and or-able values. SR_REG extracts
+ * the register number. SR_VALUE uses the shift to prepare a value accordingly.
+ */
+
+#define __SR_REG(reg, mask, shift) (reg)
+#define SR_REG(sr) __SR_REG(sr)
+
+#define __SR_VALUE(reg, mask, shift, val) ((val) << (shift))
+#define SR_VALUE(sr, val) __SR_VALUE(sr, (val))
+
+/* ----- USB commands without data ----------------------------------------- */
+
+/* To reduce the number of error checks in the code, we record the first error
+ * in atusb->err and reject all subsequent requests until the error is cleared.
+ */
+
+static int atusb_control_msg(struct atusb *atusb, unsigned int pipe,
+ __u8 request, __u8 requesttype,
+ __u16 value, __u16 index,
+ void *data, __u16 size, int timeout)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+ int ret;
+
+ if (atusb->err)
+ return atusb->err;
+
+ ret = usb_control_msg(usb_dev, pipe, request, requesttype,
+ value, index, data, size, timeout);
+ if (ret < 0) {
+ atusb->err = ret;
+ dev_err(&usb_dev->dev,
+ "atusb_control_msg: req 0x%02x val 0x%x idx 0x%x, error %d\n",
+ request, value, index, ret);
+ }
+ return ret;
+}
+
+static int atusb_command(struct atusb *atusb, uint8_t cmd, uint8_t arg)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+
+ dev_dbg(&usb_dev->dev, "atusb_command: cmd = 0x%x\n", cmd);
+ return atusb_control_msg(atusb, usb_sndctrlpipe(usb_dev, 0),
+ cmd, ATUSB_REQ_TO_DEV, arg, 0, NULL, 0, 1000);
+}
+
+static int atusb_write_reg(struct atusb *atusb, uint8_t reg, uint8_t value)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+
+ dev_dbg(&usb_dev->dev, "atusb_write_reg: 0x%02x <- 0x%02x\n",
+ reg, value);
+ return atusb_control_msg(atusb, usb_sndctrlpipe(usb_dev, 0),
+ ATUSB_REG_WRITE, ATUSB_REQ_TO_DEV,
+ value, reg, NULL, 0, 1000);
+}
+
+static int atusb_read_reg(struct atusb *atusb, uint8_t reg)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+ int ret;
+ uint8_t value;
+
+ dev_dbg(&usb_dev->dev, "atusb: reg = 0x%x\n", reg);
+ ret = atusb_control_msg(atusb, usb_rcvctrlpipe(usb_dev, 0),
+ ATUSB_REG_READ, ATUSB_REQ_FROM_DEV,
+ 0, reg, &value, 1, 1000);
+ return ret >= 0 ? value : ret;
+}
+
+static int atusb_get_and_clear_error(struct atusb *atusb)
+{
+ int err = atusb->err;
+
+ atusb->err = 0;
+ return err;
+}
+
+/* ----- skb allocation ---------------------------------------------------- */
+
+#define MAX_PSDU 127
+#define MAX_RX_XFER (1 + MAX_PSDU + 2 + 1) /* PHR+PSDU+CRC+LQI */
+
+#define SKB_ATUSB(skb) (*(struct atusb **)(skb)->cb)
+
+static void atusb_in(struct urb *urb);
+
+static int atusb_submit_rx_urb(struct atusb *atusb, struct urb *urb)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+ struct sk_buff *skb = urb->context;
+ int ret;
+
+ if (!skb) {
+ skb = alloc_skb(MAX_RX_XFER, GFP_KERNEL);
+ if (!skb) {
+ dev_warn_ratelimited(&usb_dev->dev,
+ "atusb_in: can't allocate skb\n");
+ return -ENOMEM;
+ }
+ skb_put(skb, MAX_RX_XFER);
+ SKB_ATUSB(skb) = atusb;
+ }
+
+ usb_fill_bulk_urb(urb, usb_dev, usb_rcvbulkpipe(usb_dev, 1),
+ skb->data, MAX_RX_XFER, atusb_in, skb);
+ usb_anchor_urb(urb, &atusb->rx_urbs);
+
+ ret = usb_submit_urb(urb, GFP_KERNEL);
+ if (ret) {
+ usb_unanchor_urb(urb);
+ kfree_skb(skb);
+ urb->context = NULL;
+ }
+ return ret;
+}
+
+static void atusb_work_urbs(struct work_struct *work)
+{
+ struct atusb *atusb =
+ container_of(to_delayed_work(work), struct atusb, work);
+ struct usb_device *usb_dev = atusb->usb_dev;
+ struct urb *urb;
+ int ret;
+
+ if (atusb->shutdown)
+ return;
+
+ do {
+ urb = usb_get_from_anchor(&atusb->idle_urbs);
+ if (!urb)
+ return;
+ ret = atusb_submit_rx_urb(atusb, urb);
+ } while (!ret);
+
+ usb_anchor_urb(urb, &atusb->idle_urbs);
+ dev_warn_ratelimited(&usb_dev->dev,
+ "atusb_in: can't allocate/submit URB (%d)\n", ret);
+ schedule_delayed_work(&atusb->work,
+ msecs_to_jiffies(ATUSB_ALLOC_DELAY_MS) + 1);
+}
+
+/* ----- Asynchronous USB -------------------------------------------------- */
+
+static void atusb_tx_done(struct atusb *atusb, uint8_t seq)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+ uint8_t expect = atusb->tx_ack_seq;
+
+ dev_dbg(&usb_dev->dev, "atusb_tx_done (0x%02x/0x%02x)\n", seq, expect);
+ if (seq == expect) {
+ /* TODO check for ifs handling in firmware */
+ ieee802154_xmit_complete(atusb->hw, atusb->tx_skb, false);
+ } else {
+ /* TODO I experience this case when atusb has a tx complete
+ * irq before probing, we should fix the firmware it's an
+ * unlikely case now that seq == expect is then true, but can
+ * happen and fail with a tx_skb = NULL;
+ */
+ ieee802154_wake_queue(atusb->hw);
+ if (atusb->tx_skb)
+ dev_kfree_skb_irq(atusb->tx_skb);
+ }
+}
+
+static void atusb_in_good(struct urb *urb)
+{
+ struct usb_device *usb_dev = urb->dev;
+ struct sk_buff *skb = urb->context;
+ struct atusb *atusb = SKB_ATUSB(skb);
+ uint8_t len, lqi;
+
+ if (!urb->actual_length) {
+ dev_dbg(&usb_dev->dev, "atusb_in: zero-sized URB ?\n");
+ return;
+ }
+
+ len = *skb->data;
+
+ if (urb->actual_length == 1) {
+ atusb_tx_done(atusb, len);
+ return;
+ }
+
+ if (len + 1 > urb->actual_length - 1) {
+ dev_dbg(&usb_dev->dev, "atusb_in: frame len %d+1 > URB %u-1\n",
+ len, urb->actual_length);
+ return;
+ }
+
+ if (!ieee802154_is_valid_psdu_len(len)) {
+ dev_dbg(&usb_dev->dev, "atusb_in: frame corrupted\n");
+ return;
+ }
+
+ lqi = skb->data[len + 1];
+ dev_dbg(&usb_dev->dev, "atusb_in: rx len %d lqi 0x%02x\n", len, lqi);
+ skb_pull(skb, 1); /* remove PHR */
+ skb_trim(skb, len); /* get payload only */
+ ieee802154_rx_irqsafe(atusb->hw, skb, lqi);
+ urb->context = NULL; /* skb is gone */
+}
+
+static void atusb_in(struct urb *urb)
+{
+ struct usb_device *usb_dev = urb->dev;
+ struct sk_buff *skb = urb->context;
+ struct atusb *atusb = SKB_ATUSB(skb);
+
+ dev_dbg(&usb_dev->dev, "atusb_in: status %d len %d\n",
+ urb->status, urb->actual_length);
+ if (urb->status) {
+ if (urb->status == -ENOENT) { /* being killed */
+ kfree_skb(skb);
+ urb->context = NULL;
+ return;
+ }
+ dev_dbg(&usb_dev->dev, "atusb_in: URB error %d\n", urb->status);
+ } else {
+ atusb_in_good(urb);
+ }
+
+ usb_anchor_urb(urb, &atusb->idle_urbs);
+ if (!atusb->shutdown)
+ schedule_delayed_work(&atusb->work, 0);
+}
+
+/* ----- URB allocation/deallocation --------------------------------------- */
+
+static void atusb_free_urbs(struct atusb *atusb)
+{
+ struct urb *urb;
+
+ while (1) {
+ urb = usb_get_from_anchor(&atusb->idle_urbs);
+ if (!urb)
+ break;
+ if (urb->context)
+ kfree_skb(urb->context);
+ usb_free_urb(urb);
+ }
+}
+
+static int atusb_alloc_urbs(struct atusb *atusb, int n)
+{
+ struct urb *urb;
+
+ while (n) {
+ urb = usb_alloc_urb(0, GFP_KERNEL);
+ if (!urb) {
+ atusb_free_urbs(atusb);
+ return -ENOMEM;
+ }
+ usb_anchor_urb(urb, &atusb->idle_urbs);
+ n--;
+ }
+ return 0;
+}
+
+/* ----- IEEE 802.15.4 interface operations -------------------------------- */
+
+static void atusb_xmit_complete(struct urb *urb)
+{
+ dev_dbg(&urb->dev->dev, "atusb_xmit urb completed");
+}
+
+static int atusb_xmit(struct ieee802154_hw *hw, struct sk_buff *skb)
+{
+ struct atusb *atusb = hw->priv;
+ struct usb_device *usb_dev = atusb->usb_dev;
+ int ret;
+
+ dev_dbg(&usb_dev->dev, "atusb_xmit (%d)\n", skb->len);
+ atusb->tx_skb = skb;
+ atusb->tx_ack_seq++;
+ atusb->tx_dr.wIndex = cpu_to_le16(atusb->tx_ack_seq);
+ atusb->tx_dr.wLength = cpu_to_le16(skb->len);
+
+ usb_fill_control_urb(atusb->tx_urb, usb_dev,
+ usb_sndctrlpipe(usb_dev, 0),
+ (unsigned char *)&atusb->tx_dr, skb->data,
+ skb->len, atusb_xmit_complete, NULL);
+ ret = usb_submit_urb(atusb->tx_urb, GFP_ATOMIC);
+ dev_dbg(&usb_dev->dev, "atusb_xmit done (%d)\n", ret);
+ return ret;
+}
+
+static int atusb_channel(struct ieee802154_hw *hw, u8 page, u8 channel)
+{
+ struct atusb *atusb = hw->priv;
+ int ret;
+
+ /* This implicitly sets the CCA (Clear Channel Assessment) mode to 0,
+ * "Mode 3a, Carrier sense OR energy above threshold".
+ * We should probably make this configurable. @@@
+ */
+ ret = atusb_write_reg(atusb, RG_PHY_CC_CCA, channel);
+ if (ret < 0)
+ return ret;
+ msleep(1); /* @@@ ugly synchronization */
+ return 0;
+}
+
+static int atusb_ed(struct ieee802154_hw *hw, u8 *level)
+{
+ /* @@@ not used by the stack yet */
+ *level = 0;
+ return 0;
+}
+
+static int atusb_set_hw_addr_filt(struct ieee802154_hw *hw,
+ struct ieee802154_hw_addr_filt *filt,
+ unsigned long changed)
+{
+ struct atusb *atusb = hw->priv;
+ struct device *dev = &atusb->usb_dev->dev;
+ uint8_t reg;
+
+ if (changed & IEEE802154_AFILT_SADDR_CHANGED) {
+ u16 addr = le16_to_cpu(filt->short_addr);
+
+ dev_vdbg(dev, "atusb_set_hw_addr_filt called for saddr\n");
+ atusb_write_reg(atusb, RG_SHORT_ADDR_0, addr);
+ atusb_write_reg(atusb, RG_SHORT_ADDR_1, addr >> 8);
+ }
+
+ if (changed & IEEE802154_AFILT_PANID_CHANGED) {
+ u16 pan = le16_to_cpu(filt->pan_id);
+
+ dev_vdbg(dev, "atusb_set_hw_addr_filt called for pan id\n");
+ atusb_write_reg(atusb, RG_PAN_ID_0, pan);
+ atusb_write_reg(atusb, RG_PAN_ID_1, pan >> 8);
+ }
+
+ if (changed & IEEE802154_AFILT_IEEEADDR_CHANGED) {
+ u8 i, addr[IEEE802154_EXTENDED_ADDR_LEN];
+
+ memcpy(addr, &filt->ieee_addr, IEEE802154_EXTENDED_ADDR_LEN);
+ dev_vdbg(dev, "atusb_set_hw_addr_filt called for IEEE addr\n");
+ for (i = 0; i < 8; i++)
+ atusb_write_reg(atusb, RG_IEEE_ADDR_0 + i, addr[i]);
+ }
+
+ if (changed & IEEE802154_AFILT_PANC_CHANGED) {
+ dev_vdbg(dev,
+ "atusb_set_hw_addr_filt called for panc change\n");
+ reg = atusb_read_reg(atusb, SR_REG(SR_AACK_I_AM_COORD));
+ if (filt->pan_coord)
+ reg |= SR_VALUE(SR_AACK_I_AM_COORD, 1);
+ else
+ reg &= ~SR_VALUE(SR_AACK_I_AM_COORD, 1);
+ atusb_write_reg(atusb, SR_REG(SR_AACK_I_AM_COORD), reg);
+ }
+
+ return atusb_get_and_clear_error(atusb);
+}
+
+static int atusb_start(struct ieee802154_hw *hw)
+{
+ struct atusb *atusb = hw->priv;
+ struct usb_device *usb_dev = atusb->usb_dev;
+ int ret;
+
+ dev_dbg(&usb_dev->dev, "atusb_start\n");
+ schedule_delayed_work(&atusb->work, 0);
+ atusb_command(atusb, ATUSB_RX_MODE, 1);
+ ret = atusb_get_and_clear_error(atusb);
+ if (ret < 0)
+ usb_kill_anchored_urbs(&atusb->idle_urbs);
+ return ret;
+}
+
+static void atusb_stop(struct ieee802154_hw *hw)
+{
+ struct atusb *atusb = hw->priv;
+ struct usb_device *usb_dev = atusb->usb_dev;
+
+ dev_dbg(&usb_dev->dev, "atusb_stop\n");
+ usb_kill_anchored_urbs(&atusb->idle_urbs);
+ atusb_command(atusb, ATUSB_RX_MODE, 0);
+ atusb_get_and_clear_error(atusb);
+}
+
+static struct ieee802154_ops atusb_ops = {
+ .owner = THIS_MODULE,
+ .xmit_async = atusb_xmit,
+ .ed = atusb_ed,
+ .set_channel = atusb_channel,
+ .start = atusb_start,
+ .stop = atusb_stop,
+ .set_hw_addr_filt = atusb_set_hw_addr_filt,
+};
+
+/* ----- Firmware and chip version information ----------------------------- */
+
+static int atusb_get_and_show_revision(struct atusb *atusb)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+ unsigned char buffer[3];
+ int ret;
+
+ /* Get a couple of the ATMega Firmware values */
+ ret = atusb_control_msg(atusb, usb_rcvctrlpipe(usb_dev, 0),
+ ATUSB_ID, ATUSB_REQ_FROM_DEV, 0, 0,
+ buffer, 3, 1000);
+ if (ret >= 0)
+ dev_info(&usb_dev->dev,
+ "Firmware: major: %u, minor: %u, hardware type: %u\n",
+ buffer[0], buffer[1], buffer[2]);
+
+ return ret;
+}
+
+static int atusb_get_and_show_build(struct atusb *atusb)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+ char build[ATUSB_BUILD_SIZE + 1];
+ int ret;
+
+ ret = atusb_control_msg(atusb, usb_rcvctrlpipe(usb_dev, 0),
+ ATUSB_BUILD, ATUSB_REQ_FROM_DEV, 0, 0,
+ build, ATUSB_BUILD_SIZE, 1000);
+ if (ret >= 0) {
+ build[ret] = 0;
+ dev_info(&usb_dev->dev, "Firmware: build %s\n", build);
+ }
+
+ return ret;
+}
+
+static int atusb_get_and_show_chip(struct atusb *atusb)
+{
+ struct usb_device *usb_dev = atusb->usb_dev;
+ uint8_t man_id_0, man_id_1, part_num, version_num;
+
+ man_id_0 = atusb_read_reg(atusb, RG_MAN_ID_0);
+ man_id_1 = atusb_read_reg(atusb, RG_MAN_ID_1);
+ part_num = atusb_read_reg(atusb, RG_PART_NUM);
+ version_num = atusb_read_reg(atusb, RG_VERSION_NUM);
+
+ if (atusb->err)
+ return atusb->err;
+
+ if ((man_id_1 << 8 | man_id_0) != ATUSB_JEDEC_ATMEL) {
+ dev_err(&usb_dev->dev,
+ "non-Atmel transceiver xxxx%02x%02x\n",
+ man_id_1, man_id_0);
+ goto fail;
+ }
+ if (part_num != 3) {
+ dev_err(&usb_dev->dev,
+ "unexpected transceiver, part 0x%02x version 0x%02x\n",
+ part_num, version_num);
+ goto fail;
+ }
+
+ dev_info(&usb_dev->dev, "ATUSB: AT86RF231 version %d\n", version_num);
+
+ return 0;
+
+fail:
+ atusb->err = -ENODEV;
+ return -ENODEV;
+}
+
+/* ----- Setup ------------------------------------------------------------- */
+
+static int atusb_probe(struct usb_interface *interface,
+ const struct usb_device_id *id)
+{
+ struct usb_device *usb_dev = interface_to_usbdev(interface);
+ struct ieee802154_hw *hw;
+ struct atusb *atusb = NULL;
+ int ret = -ENOMEM;
+
+ hw = ieee802154_alloc_hw(sizeof(struct atusb), &atusb_ops);
+ if (!hw)
+ return -ENOMEM;
+
+ atusb = hw->priv;
+ atusb->hw = hw;
+ atusb->usb_dev = usb_get_dev(usb_dev);
+ usb_set_intfdata(interface, atusb);
+
+ atusb->shutdown = 0;
+ atusb->err = 0;
+ INIT_DELAYED_WORK(&atusb->work, atusb_work_urbs);
+ init_usb_anchor(&atusb->idle_urbs);
+ init_usb_anchor(&atusb->rx_urbs);
+
+ if (atusb_alloc_urbs(atusb, ATUSB_NUM_RX_URBS))
+ goto fail;
+
+ atusb->tx_dr.bRequestType = ATUSB_REQ_TO_DEV;
+ atusb->tx_dr.bRequest = ATUSB_TX;
+ atusb->tx_dr.wValue = cpu_to_le16(0);
+
+ atusb->tx_urb = usb_alloc_urb(0, GFP_ATOMIC);
+ if (!atusb->tx_urb)
+ goto fail;
+
+ hw->parent = &usb_dev->dev;
+ hw->flags = IEEE802154_HW_TX_OMIT_CKSUM | IEEE802154_HW_AFILT;
+
+ hw->phy->current_page = 0;
+ hw->phy->current_channel = 11; /* reset default */
+ hw->phy->supported.channels[0] = 0x7FFF800;
+ ieee802154_random_extended_addr(&hw->phy->perm_extended_addr);
+
+ atusb_command(atusb, ATUSB_RF_RESET, 0);
+ atusb_get_and_show_chip(atusb);
+ atusb_get_and_show_revision(atusb);
+ atusb_get_and_show_build(atusb);
+ ret = atusb_get_and_clear_error(atusb);
+ if (ret) {
+ dev_err(&atusb->usb_dev->dev,
+ "%s: initialization failed, error = %d\n",
+ __func__, ret);
+ goto fail;
+ }
+
+ ret = ieee802154_register_hw(hw);
+ if (ret)
+ goto fail;
+
+ /* If we just powered on, we're now in P_ON and need to enter TRX_OFF
+ * explicitly. Any resets after that will send us straight to TRX_OFF,
+ * making the command below redundant.
+ */
+ atusb_write_reg(atusb, RG_TRX_STATE, STATE_FORCE_TRX_OFF);
+ msleep(1); /* reset => TRX_OFF, tTR13 = 37 us */
+
+#if 0
+ /* Calculating the maximum time available to empty the frame buffer
+ * on reception:
+ *
+ * According to [1], the inter-frame gap is
+ * R * 20 * 16 us + 128 us
+ * where R is a random number from 0 to 7. Furthermore, we have 20 bit
+ * times (80 us at 250 kbps) of SHR of the next frame before the
+ * transceiver begins storing data in the frame buffer.
+ *
+ * This yields a minimum time of 208 us between the last data of a
+ * frame and the first data of the next frame. This time is further
+ * reduced by interrupt latency in the atusb firmware.
+ *
+ * atusb currently needs about 500 us to retrieve a maximum-sized
+ * frame. We therefore have to allow reception of a new frame to begin
+ * while we retrieve the previous frame.
+ *
+ * [1] "JN-AN-1035 Calculating data rates in an IEEE 802.15.4-based
+ * network", Jennic 2006.
+ * http://www.jennic.com/download_file.php?supportFile=JN-AN-1035%20Calculating%20802-15-4%20Data%20Rates-1v0.pdf
+ */
+
+ atusb_write_reg(atusb,
+ SR_REG(SR_RX_SAFE_MODE), SR_VALUE(SR_RX_SAFE_MODE, 1));
+#endif
+ atusb_write_reg(atusb, RG_IRQ_MASK, 0xff);
+
+ ret = atusb_get_and_clear_error(atusb);
+ if (!ret)
+ return 0;
+
+ dev_err(&atusb->usb_dev->dev,
+ "%s: setup failed, error = %d\n",
+ __func__, ret);
+
+ ieee802154_unregister_hw(hw);
+fail:
+ atusb_free_urbs(atusb);
+ usb_kill_urb(atusb->tx_urb);
+ usb_free_urb(atusb->tx_urb);
+ usb_put_dev(usb_dev);
+ ieee802154_free_hw(hw);
+ return ret;
+}
+
+static void atusb_disconnect(struct usb_interface *interface)
+{
+ struct atusb *atusb = usb_get_intfdata(interface);
+
+ dev_dbg(&atusb->usb_dev->dev, "atusb_disconnect\n");
+
+ atusb->shutdown = 1;
+ cancel_delayed_work_sync(&atusb->work);
+
+ usb_kill_anchored_urbs(&atusb->rx_urbs);
+ atusb_free_urbs(atusb);
+ usb_kill_urb(atusb->tx_urb);
+ usb_free_urb(atusb->tx_urb);
+
+ ieee802154_unregister_hw(atusb->hw);
+
+ ieee802154_free_hw(atusb->hw);
+
+ usb_set_intfdata(interface, NULL);
+ usb_put_dev(atusb->usb_dev);
+
+ pr_debug("atusb_disconnect done\n");
+}
+
+/* The devices we work with */
+static const struct usb_device_id atusb_device_table[] = {
+ {
+ .match_flags = USB_DEVICE_ID_MATCH_DEVICE |
+ USB_DEVICE_ID_MATCH_INT_INFO,
+ .idVendor = ATUSB_VENDOR_ID,
+ .idProduct = ATUSB_PRODUCT_ID,
+ .bInterfaceClass = USB_CLASS_VENDOR_SPEC
+ },
+ /* end with null element */
+ {}
+};
+MODULE_DEVICE_TABLE(usb, atusb_device_table);
+
+static struct usb_driver atusb_driver = {
+ .name = "atusb",
+ .probe = atusb_probe,
+ .disconnect = atusb_disconnect,
+ .id_table = atusb_device_table,
+};
+module_usb_driver(atusb_driver);
+
+MODULE_AUTHOR("Alexander Aring <alex.aring@gmail.com>");
+MODULE_AUTHOR("Richard Sharpe <realrichardsharpe@gmail.com>");
+MODULE_AUTHOR("Stefan Schmidt <stefan@datenfreihafen.org>");
+MODULE_AUTHOR("Werner Almesberger <werner@almesberger.net>");
+MODULE_DESCRIPTION("ATUSB IEEE 802.15.4 Driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * atusb.h - Definitions shared between kernel and ATUSB firmware
+ *
+ * Written 2013 by Werner Almesberger <werner@almesberger.net>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2, or
+ * (at your option) any later version.
+ *
+ * This file should be identical for kernel and firmware.
+ * Kernel: drivers/net/ieee802154/atusb.h
+ * Firmware: ben-wpan/atusb/fw/include/atusb/atusb.h
+ */
+
+#ifndef _ATUSB_H
+#define _ATUSB_H
+
+#define ATUSB_VENDOR_ID 0x20b7 /* Qi Hardware*/
+#define ATUSB_PRODUCT_ID 0x1540 /* 802.15.4, device 0 */
+ /* -- - - */
+
+#define ATUSB_BUILD_SIZE 256 /* maximum build version/date message length */
+
+/* Commands to our device. Make sure this is synced with the firmware */
+enum atusb_requests {
+ ATUSB_ID = 0x00, /* system status/control grp */
+ ATUSB_BUILD,
+ ATUSB_RESET,
+ ATUSB_RF_RESET = 0x10, /* debug/test group */
+ ATUSB_POLL_INT,
+ ATUSB_TEST, /* atusb-sil only */
+ ATUSB_TIMER,
+ ATUSB_GPIO,
+ ATUSB_SLP_TR,
+ ATUSB_GPIO_CLEANUP,
+ ATUSB_REG_WRITE = 0x20, /* transceiver group */
+ ATUSB_REG_READ,
+ ATUSB_BUF_WRITE,
+ ATUSB_BUF_READ,
+ ATUSB_SRAM_WRITE,
+ ATUSB_SRAM_READ,
+ ATUSB_SPI_WRITE = 0x30, /* SPI group */
+ ATUSB_SPI_READ1,
+ ATUSB_SPI_READ2,
+ ATUSB_SPI_WRITE2_SYNC,
+ ATUSB_RX_MODE = 0x40, /* HardMAC group */
+ ATUSB_TX,
+};
+
+/* Direction bRequest wValue wIndex wLength
+ *
+ * ->host ATUSB_ID - - 3
+ * ->host ATUSB_BUILD - - #bytes
+ * host-> ATUSB_RESET - - 0
+ *
+ * host-> ATUSB_RF_RESET - - 0
+ * ->host ATUSB_POLL_INT - - 1
+ * host-> ATUSB_TEST - - 0
+ * ->host ATUSB_TIMER - - #bytes (6)
+ * ->host ATUSB_GPIO dir+data mask+p# 3
+ * host-> ATUSB_SLP_TR - - 0
+ * host-> ATUSB_GPIO_CLEANUP - - 0
+ *
+ * host-> ATUSB_REG_WRITE value addr 0
+ * ->host ATUSB_REG_READ - addr 1
+ * host-> ATUSB_BUF_WRITE - - #bytes
+ * ->host ATUSB_BUF_READ - - #bytes
+ * host-> ATUSB_SRAM_WRITE - addr #bytes
+ * ->host ATUSB_SRAM_READ - addr #bytes
+ *
+ * host-> ATUSB_SPI_WRITE byte0 byte1 #bytes
+ * ->host ATUSB_SPI_READ1 byte0 - #bytes
+ * ->host ATUSB_SPI_READ2 byte0 byte1 #bytes
+ * ->host ATUSB_SPI_WRITE2_SYNC byte0 byte1 0/1
+ *
+ * host-> ATUSB_RX_MODE on - 0
+ * host-> ATUSB_TX flags ack_seq #bytes
+ */
+
+#define ATUSB_REQ_FROM_DEV (USB_TYPE_VENDOR | USB_DIR_IN)
+#define ATUSB_REQ_TO_DEV (USB_TYPE_VENDOR | USB_DIR_OUT)
+
+#endif /* !_ATUSB_H */
projects / platform / kernel / linux-starfive.git / commitdiff