--- /dev/null
+* Cypress cyttsp touchscreen controller
+
+Required properties:
+ - compatible : must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi"
+ - reg : Device I2C address or SPI chip select number
+ - spi-max-frequency : Maximum SPI clocking speed of the device (for cyttsp-spi)
+ - interrupt-parent : the phandle for the gpio controller
+ (see interrupt binding[0]).
+ - interrupts : (gpio) interrupt to which the chip is connected
+ (see interrupt binding[0]).
+ - bootloader-key : the 8-byte bootloader key that is required to switch
+ the chip from bootloader mode (default mode) to
+ application mode.
+ This property has to be specified as an array of 8
+ '/bits/ 8' values.
+
+Optional properties:
+ - reset-gpios : the reset gpio the chip is connected to
+ (see GPIO binding[1] for more details).
+ - touchscreen-size-x : horizontal resolution of touchscreen (in pixels)
+ - touchscreen-size-y : vertical resolution of touchscreen (in pixels)
+ - touchscreen-fuzz-x : horizontal noise value of the absolute input device
+ (in pixels)
+ - touchscreen-fuzz-y : vertical noise value of the absolute input device
+ (in pixels)
+ - active-distance : the distance in pixels beyond which a touch must move
+ before movement is detected and reported by the device.
+ Valid values: 0-15.
+ - active-interval-ms : the minimum period in ms between consecutive
+ scanning/processing cycles when the chip is in active mode.
+ Valid values: 0-255.
+ - lowpower-interval-ms : the minimum period in ms between consecutive
+ scanning/processing cycles when the chip is in low-power mode.
+ Valid values: 0-2550
+ - touch-timeout-ms : minimum time in ms spent in the active power state while no
+ touches are detected before entering low-power mode.
+ Valid values: 0-2550
+ - use-handshake : enable register-based handshake (boolean). This should
+ only be used if the chip is configured to use 'blocking
+ communication with timeout' (in this case the device
+ generates an interrupt at the end of every
+ scanning/processing cycle).
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+
+Example:
+ &i2c1 {
+ /* ... */
+ cyttsp@a {
+ compatible = "cypress,cyttsp-i2c";
+ reg = <0xa>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <28 0>;
+ reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-fuzz-x = <4>;
+ touchscreen-fuzz-y = <7>;
+
+ bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>;
+ active-distance = <8>;
+ active-interval-ms = <0>;
+ lowpower-interval-ms = <200>;
+ touch-timeout-ms = <100>;
+ };
+
+ /* ... */
+ };
+
+ &mcspi1 {
+ /* ... */
+ cyttsp@0 {
+ compatible = "cypress,cyttsp-spi";
+ spi-max-frequency = <6000000>;
+ reg = <0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <28 0>;
+ reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-fuzz-x = <4>;
+ touchscreen-fuzz-y = <7>;
+
+ bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>;
+ active-distance = <8>;
+ active-interval-ms = <0>;
+ lowpower-interval-ms = <200>;
+ touch-timeout-ms = <100>;
+ };
+
+ /* ... */
+ };
#include <linux/delay.h>
#include <linux/input.h>
#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
+#include <linux/property.h>
+#include <linux/gpio/consumer.h>
#include "cyttsp_core.h"
#define CY_DELAY_DFLT 20 /* ms */
#define CY_DELAY_MAX 500
#define CY_ACT_DIST_DFLT 0xF8
+#define CY_ACT_DIST_MASK 0x0F
#define CY_HNDSHK_BIT 0x80
/* device mode bits */
#define CY_OPERATE_MODE 0x00
static int cyttsp_handshake(struct cyttsp *ts)
{
- if (ts->pdata->use_hndshk)
+ if (ts->use_hndshk)
return ttsp_send_command(ts,
ts->xy_data.hst_mode ^ CY_HNDSHK_BIT);
u8 bl_cmd[sizeof(bl_command)];
memcpy(bl_cmd, bl_command, sizeof(bl_command));
- if (ts->pdata->bl_keys)
+ if (ts->bl_keys)
memcpy(&bl_cmd[sizeof(bl_command) - CY_NUM_BL_KEYS],
- ts->pdata->bl_keys, CY_NUM_BL_KEYS);
+ ts->bl_keys, CY_NUM_BL_KEYS);
error = ttsp_write_block_data(ts, CY_REG_BASE,
sizeof(bl_cmd), bl_cmd);
{
int retval = 0;
- if (ts->pdata->act_intrvl != CY_ACT_INTRVL_DFLT ||
- ts->pdata->tch_tmout != CY_TCH_TMOUT_DFLT ||
- ts->pdata->lp_intrvl != CY_LP_INTRVL_DFLT) {
+ if (ts->act_intrvl != CY_ACT_INTRVL_DFLT ||
+ ts->tch_tmout != CY_TCH_TMOUT_DFLT ||
+ ts->lp_intrvl != CY_LP_INTRVL_DFLT) {
u8 intrvl_ray[] = {
- ts->pdata->act_intrvl,
- ts->pdata->tch_tmout,
- ts->pdata->lp_intrvl
+ ts->act_intrvl,
+ ts->tch_tmout,
+ ts->lp_intrvl
};
/* set intrvl registers */
static int cyttsp_act_dist_setup(struct cyttsp *ts)
{
- u8 act_dist_setup = ts->pdata->act_dist;
+ u8 act_dist_setup = ts->act_dist;
/* Init gesture; active distance setup */
return ttsp_write_block_data(ts, CY_REG_ACT_DIST,
cyttsp_disable(ts);
}
-static void cyttsp_platform_exit(void *data)
+static int cyttsp_parse_properties(struct cyttsp *ts)
{
- struct cyttsp *ts = data;
+ struct device *dev = ts->dev;
+ u32 dt_value;
+ int ret;
+
+ ts->bl_keys = devm_kzalloc(dev, CY_NUM_BL_KEYS, GFP_KERNEL);
+ if (!ts->bl_keys)
+ return -ENOMEM;
+
+ /* Set some default values */
+ ts->use_hndshk = false;
+ ts->act_dist = CY_ACT_DIST_DFLT;
+ ts->act_intrvl = CY_ACT_INTRVL_DFLT;
+ ts->tch_tmout = CY_TCH_TMOUT_DFLT;
+ ts->lp_intrvl = CY_LP_INTRVL_DFLT;
+
+ ret = device_property_read_u8_array(dev, "bootloader-key",
+ ts->bl_keys, CY_NUM_BL_KEYS);
+ if (ret) {
+ dev_err(dev,
+ "bootloader-key property could not be retrieved\n");
+ return ret;
+ }
+
+ ts->use_hndshk = device_property_present(dev, "use-handshake");
+
+ if (!device_property_read_u32(dev, "active-distance", &dt_value)) {
+ if (dt_value > 15) {
+ dev_err(dev, "active-distance (%u) must be [0-15]\n",
+ dt_value);
+ return -EINVAL;
+ }
+ ts->act_dist &= ~CY_ACT_DIST_MASK;
+ ts->act_dist |= dt_value;
+ }
+
+ if (!device_property_read_u32(dev, "active-interval-ms", &dt_value)) {
+ if (dt_value > 255) {
+ dev_err(dev, "active-interval-ms (%u) must be [0-255]\n",
+ dt_value);
+ return -EINVAL;
+ }
+ ts->act_intrvl = dt_value;
+ }
- if (ts->pdata->exit)
- ts->pdata->exit();
+ if (!device_property_read_u32(dev, "lowpower-interval-ms", &dt_value)) {
+ if (dt_value > 2550) {
+ dev_err(dev, "lowpower-interval-ms (%u) must be [0-2550]\n",
+ dt_value);
+ return -EINVAL;
+ }
+ /* Register value is expressed in 0.01s / bit */
+ ts->lp_intrvl = dt_value / 10;
+ }
+
+ if (!device_property_read_u32(dev, "touch-timeout-ms", &dt_value)) {
+ if (dt_value > 2550) {
+ dev_err(dev, "touch-timeout-ms (%u) must be [0-2550]\n",
+ dt_value);
+ return -EINVAL;
+ }
+ /* Register value is expressed in 0.01s / bit */
+ ts->tch_tmout = dt_value / 10;
+ }
+
+ return 0;
}
struct cyttsp *cyttsp_probe(const struct cyttsp_bus_ops *bus_ops,
struct device *dev, int irq, size_t xfer_buf_size)
{
- const struct cyttsp_platform_data *pdata = dev_get_platdata(dev);
struct cyttsp *ts;
struct input_dev *input_dev;
int error;
- if (!pdata || !pdata->name || irq <= 0)
- return ERR_PTR(-EINVAL);
-
ts = devm_kzalloc(dev, sizeof(*ts) + xfer_buf_size, GFP_KERNEL);
if (!ts)
return ERR_PTR(-ENOMEM);
ts->dev = dev;
ts->input = input_dev;
- ts->pdata = dev_get_platdata(dev);
ts->bus_ops = bus_ops;
ts->irq = irq;
- init_completion(&ts->bl_ready);
- snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(dev));
-
- error = devm_add_action(dev, cyttsp_platform_exit, ts);
- if (error) {
- dev_err(dev, "failed to install exit action: %d\n", error);
+ ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(ts->reset_gpio)) {
+ error = PTR_ERR(ts->reset_gpio);
+ dev_err(dev, "Failed to request reset gpio, error %d\n", error);
return ERR_PTR(error);
}
- if (pdata->init) {
- error = pdata->init();
- if (error) {
- dev_err(ts->dev, "platform init failed, err: %d\n",
- error);
- return ERR_PTR(error);
- }
- }
+ error = cyttsp_parse_properties(ts);
+ if (error)
+ return ERR_PTR(error);
+
+ init_completion(&ts->bl_ready);
+ snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(dev));
- input_dev->name = pdata->name;
+ input_dev->name = "Cypress TTSP TouchScreen";
input_dev->phys = ts->phys;
input_dev->id.bustype = bus_ops->bustype;
input_dev->dev.parent = ts->dev;
input_set_drvdata(input_dev, ts);
- __set_bit(EV_ABS, input_dev->evbit);
- input_set_abs_params(input_dev, ABS_MT_POSITION_X,
- 0, pdata->maxx, 0, 0);
- input_set_abs_params(input_dev, ABS_MT_POSITION_Y,
- 0, pdata->maxy, 0, 0);
- input_set_abs_params(input_dev, ABS_MT_TOUCH_MAJOR,
- 0, CY_MAXZ, 0, 0);
+ input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_X);
+ input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_Y);
+ touchscreen_parse_properties(input_dev, true);
error = input_mt_init_slots(input_dev, CY_MAX_ID, 0);
if (error) {
error = devm_request_threaded_irq(dev, ts->irq, NULL, cyttsp_irq,
IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
- pdata->name, ts);
+ "cyttsp", ts);
if (error) {
dev_err(ts->dev, "failed to request IRQ %d, err: %d\n",
ts->irq, error);
projects / platform / kernel / linux-rpi3.git / commitdiff