ARM: OMAP3: omap3evm: Adapt to ehci-omap changes

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device. VAUX2 supplies the PHY's VCC.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 48789e0..2de92fa 100644 (file)
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -496,7 +496,7 @@ struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
 static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
        REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"),    /* OMAP ISP */
        REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"),    /* OMAP ISP */
-       REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+       REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"),     /* hsusb port 2 */
        REGULATOR_SUPPLY("vaux2", NULL),
 };
 
@@ -539,17 +539,16 @@ static int __init omap3_evm_i2c_init(void)
        return 0;
 }
 
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
+static struct usbhs_phy_data phy_data[] __initdata = {
+       {
+               .port = 2,
+               .reset_gpio = -1,       /* set at runtime */
+               .vcc_gpio = -EINVAL,
+       },
+};
 
-       .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
        .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-       .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-       .phy_reset  = true,
-       /* PHY reset GPIO will be runtime programmed based on EVM version */
-       .reset_gpio_port[0]  = -EINVAL,
-       .reset_gpio_port[1]  = -EINVAL,
-       .reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -725,7 +724,7 @@ static void __init omap3_evm_init(void)
 
                /* setup EHCI phy reset config */
                omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
-               usbhs_bdata.reset_gpio_port[1] = 21;
+               phy_data[0].reset_gpio = 21;
 
                /* EVM REV >= E can supply 500mA with EXTVBUS programming */
                musb_board_data.power = 500;
@@ -733,10 +732,12 @@ static void __init omap3_evm_init(void)
        } else {
                /* setup EHCI phy reset on MDC */
                omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
-               usbhs_bdata.reset_gpio_port[1] = 135;
+               phy_data[0].reset_gpio = 135;
        }
        usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
        usb_musb_init(&musb_board_data);
+
+       usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
        usbhs_init(&usbhs_bdata);
        board_nand_init(omap3evm_nand_partitions,
                        ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,