libahci: fix result_tf handling after an ATA PIO data-in command
authorTejun Heo <tj@kernel.org>
Fri, 15 Oct 2010 09:00:08 +0000 (11:00 +0200)
committerJeff Garzik <jgarzik@redhat.com>
Fri, 22 Oct 2010 01:17:00 +0000 (21:17 -0400)
ATA devices don't send D2H Reg FIS after an successful ATA PIO data-in
command.  The host is supposed to take the TF and E_Status of the
preceding PIO Setup FIS.  Update ahci_qc_fill_rtf() such that it takes
TF + E_Status from PIO Setup FIS after a successful ATA PIO data-in
command.

Without this patch, result_tf for such a command is filled with the
content of the previous D2H Reg FIS which belongs to a previous
command, which can make the command incorrectly seen as failed.

* Patch updated to grab the whole TF + E_Status from PIO Setup FIS
  instead of just E_Status as suggested by Robert Hancock.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mark Lord <kernel@teksavvy.com>
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/ahci.h
drivers/ata/libahci.c

index 1a2aacf..329cbbb 100644 (file)
@@ -72,6 +72,7 @@ enum {
        AHCI_CMD_RESET          = (1 << 8),
        AHCI_CMD_CLR_BUSY       = (1 << 10),
 
+       RX_FIS_PIO_SETUP        = 0x20, /* offset of PIO Setup FIS data */
        RX_FIS_D2H_REG          = 0x40, /* offset of D2H Register FIS data */
        RX_FIS_SDB              = 0x58, /* offset of SDB FIS data */
        RX_FIS_UNK              = 0x60, /* offset of Unknown FIS data */
index 524dbe8..ebc08d6 100644 (file)
@@ -1752,12 +1752,24 @@ static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc)
 static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc)
 {
        struct ahci_port_priv *pp = qc->ap->private_data;
-       u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+       u8 *rx_fis = pp->rx_fis;
 
        if (pp->fbs_enabled)
-               d2h_fis += qc->dev->link->pmp * AHCI_RX_FIS_SZ;
+               rx_fis += qc->dev->link->pmp * AHCI_RX_FIS_SZ;
+
+       /*
+        * After a successful execution of an ATA PIO data-in command,
+        * the device doesn't send D2H Reg FIS to update the TF and
+        * the host should take TF and E_Status from the preceding PIO
+        * Setup FIS.
+        */
+       if (qc->tf.protocol == ATA_PROT_PIO && qc->dma_dir == DMA_FROM_DEVICE &&
+           !(qc->flags & ATA_QCFLAG_FAILED)) {
+               ata_tf_from_fis(rx_fis + RX_FIS_PIO_SETUP, &qc->result_tf);
+               qc->result_tf.command = (rx_fis + RX_FIS_PIO_SETUP)[15];
+       } else
+               ata_tf_from_fis(rx_fis + RX_FIS_D2H_REG, &qc->result_tf);
 
-       ata_tf_from_fis(d2h_fis, &qc->result_tf);
        return true;
 }