The USB OTG controller communicates with the comparator using this
driver.
+config TWL4030_USB
+ tristate "TWL4030 USB Transceiver Driver"
+ depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
+ select GENERIC_PHY
+ select USB_PHY
+ help
+ Enable this to support the USB OTG transceiver on TWL4030
+ family chips (including the TWL5030 and TPS659x0 devices).
+ This transceiver supports high and full speed devices plus,
+ in host mode, low speed.
+
endmenu
obj-$(CONFIG_GENERIC_PHY) += phy-core.o
obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
+obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
--- /dev/null
+/*
+ * twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller
+ *
+ * Copyright (C) 2004-2007 Texas Instruments
+ * Copyright (C) 2008 Nokia Corporation
+ * Contact: Felipe Balbi <felipe.balbi@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Current status:
+ * - HS USB ULPI mode works.
+ * - 3-pin mode support may be added in future.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <linux/workqueue.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/usb/otg.h>
+#include <linux/phy/phy.h>
+#include <linux/usb/musb-omap.h>
+#include <linux/usb/ulpi.h>
+#include <linux/i2c/twl.h>
+#include <linux/regulator/consumer.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+
+/* Register defines */
+
+#define MCPC_CTRL 0x30
+#define MCPC_CTRL_RTSOL (1 << 7)
+#define MCPC_CTRL_EXTSWR (1 << 6)
+#define MCPC_CTRL_EXTSWC (1 << 5)
+#define MCPC_CTRL_VOICESW (1 << 4)
+#define MCPC_CTRL_OUT64K (1 << 3)
+#define MCPC_CTRL_RTSCTSSW (1 << 2)
+#define MCPC_CTRL_HS_UART (1 << 0)
+
+#define MCPC_IO_CTRL 0x33
+#define MCPC_IO_CTRL_MICBIASEN (1 << 5)
+#define MCPC_IO_CTRL_CTS_NPU (1 << 4)
+#define MCPC_IO_CTRL_RXD_PU (1 << 3)
+#define MCPC_IO_CTRL_TXDTYP (1 << 2)
+#define MCPC_IO_CTRL_CTSTYP (1 << 1)
+#define MCPC_IO_CTRL_RTSTYP (1 << 0)
+
+#define MCPC_CTRL2 0x36
+#define MCPC_CTRL2_MCPC_CK_EN (1 << 0)
+
+#define OTHER_FUNC_CTRL 0x80
+#define OTHER_FUNC_CTRL_BDIS_ACON_EN (1 << 4)
+#define OTHER_FUNC_CTRL_FIVEWIRE_MODE (1 << 2)
+
+#define OTHER_IFC_CTRL 0x83
+#define OTHER_IFC_CTRL_OE_INT_EN (1 << 6)
+#define OTHER_IFC_CTRL_CEA2011_MODE (1 << 5)
+#define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN (1 << 4)
+#define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT (1 << 3)
+#define OTHER_IFC_CTRL_HIZ_ULPI (1 << 2)
+#define OTHER_IFC_CTRL_ALT_INT_REROUTE (1 << 0)
+
+#define OTHER_INT_EN_RISE 0x86
+#define OTHER_INT_EN_FALL 0x89
+#define OTHER_INT_STS 0x8C
+#define OTHER_INT_LATCH 0x8D
+#define OTHER_INT_VB_SESS_VLD (1 << 7)
+#define OTHER_INT_DM_HI (1 << 6) /* not valid for "latch" reg */
+#define OTHER_INT_DP_HI (1 << 5) /* not valid for "latch" reg */
+#define OTHER_INT_BDIS_ACON (1 << 3) /* not valid for "fall" regs */
+#define OTHER_INT_MANU (1 << 1)
+#define OTHER_INT_ABNORMAL_STRESS (1 << 0)
+
+#define ID_STATUS 0x96
+#define ID_RES_FLOAT (1 << 4)
+#define ID_RES_440K (1 << 3)
+#define ID_RES_200K (1 << 2)
+#define ID_RES_102K (1 << 1)
+#define ID_RES_GND (1 << 0)
+
+#define POWER_CTRL 0xAC
+#define POWER_CTRL_OTG_ENAB (1 << 5)
+
+#define OTHER_IFC_CTRL2 0xAF
+#define OTHER_IFC_CTRL2_ULPI_STP_LOW (1 << 4)
+#define OTHER_IFC_CTRL2_ULPI_TXEN_POL (1 << 3)
+#define OTHER_IFC_CTRL2_ULPI_4PIN_2430 (1 << 2)
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK (3 << 0) /* bits 0 and 1 */
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N (0 << 0)
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N (1 << 0)
+
+#define REG_CTRL_EN 0xB2
+#define REG_CTRL_ERROR 0xB5
+#define ULPI_I2C_CONFLICT_INTEN (1 << 0)
+
+#define OTHER_FUNC_CTRL2 0xB8
+#define OTHER_FUNC_CTRL2_VBAT_TIMER_EN (1 << 0)
+
+/* following registers do not have separate _clr and _set registers */
+#define VBUS_DEBOUNCE 0xC0
+#define ID_DEBOUNCE 0xC1
+#define VBAT_TIMER 0xD3
+#define PHY_PWR_CTRL 0xFD
+#define PHY_PWR_PHYPWD (1 << 0)
+#define PHY_CLK_CTRL 0xFE
+#define PHY_CLK_CTRL_CLOCKGATING_EN (1 << 2)
+#define PHY_CLK_CTRL_CLK32K_EN (1 << 1)
+#define REQ_PHY_DPLL_CLK (1 << 0)
+#define PHY_CLK_CTRL_STS 0xFF
+#define PHY_DPLL_CLK (1 << 0)
+
+/* In module TWL_MODULE_PM_MASTER */
+#define STS_HW_CONDITIONS 0x0F
+
+/* In module TWL_MODULE_PM_RECEIVER */
+#define VUSB_DEDICATED1 0x7D
+#define VUSB_DEDICATED2 0x7E
+#define VUSB1V5_DEV_GRP 0x71
+#define VUSB1V5_TYPE 0x72
+#define VUSB1V5_REMAP 0x73
+#define VUSB1V8_DEV_GRP 0x74
+#define VUSB1V8_TYPE 0x75
+#define VUSB1V8_REMAP 0x76
+#define VUSB3V1_DEV_GRP 0x77
+#define VUSB3V1_TYPE 0x78
+#define VUSB3V1_REMAP 0x79
+
+/* In module TWL4030_MODULE_INTBR */
+#define PMBR1 0x0D
+#define GPIO_USB_4PIN_ULPI_2430C (3 << 0)
+
+struct twl4030_usb {
+ struct usb_phy phy;
+ struct device *dev;
+
+ /* TWL4030 internal USB regulator supplies */
+ struct regulator *usb1v5;
+ struct regulator *usb1v8;
+ struct regulator *usb3v1;
+
+ /* for vbus reporting with irqs disabled */
+ spinlock_t lock;
+
+ /* pin configuration */
+ enum twl4030_usb_mode usb_mode;
+
+ int irq;
+ enum omap_musb_vbus_id_status linkstat;
+ bool vbus_supplied;
+ u8 asleep;
+ bool irq_enabled;
+
+ struct delayed_work id_workaround_work;
+};
+
+/* internal define on top of container_of */
+#define phy_to_twl(x) container_of((x), struct twl4030_usb, phy)
+
+/*-------------------------------------------------------------------------*/
+
+static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
+ u8 module, u8 data, u8 address)
+{
+ u8 check;
+
+ if ((twl_i2c_write_u8(module, data, address) >= 0) &&
+ (twl_i2c_read_u8(module, &check, address) >= 0) &&
+ (check == data))
+ return 0;
+ dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
+ 1, module, address, check, data);
+
+ /* Failed once: Try again */
+ if ((twl_i2c_write_u8(module, data, address) >= 0) &&
+ (twl_i2c_read_u8(module, &check, address) >= 0) &&
+ (check == data))
+ return 0;
+ dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
+ 2, module, address, check, data);
+
+ /* Failed again: Return error */
+ return -EBUSY;
+}
+
+#define twl4030_usb_write_verify(twl, address, data) \
+ twl4030_i2c_write_u8_verify(twl, TWL_MODULE_USB, (data), (address))
+
+static inline int twl4030_usb_write(struct twl4030_usb *twl,
+ u8 address, u8 data)
+{
+ int ret = 0;
+
+ ret = twl_i2c_write_u8(TWL_MODULE_USB, data, address);
+ if (ret < 0)
+ dev_dbg(twl->dev,
+ "TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
+ return ret;
+}
+
+static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8 address)
+{
+ u8 data;
+ int ret = 0;
+
+ ret = twl_i2c_read_u8(module, &data, address);
+ if (ret >= 0)
+ ret = data;
+ else
+ dev_dbg(twl->dev,
+ "TWL4030:readb[0x%x,0x%x] Error %d\n",
+ module, address, ret);
+
+ return ret;
+}
+
+static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
+{
+ return twl4030_readb(twl, TWL_MODULE_USB, address);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static inline int
+twl4030_usb_set_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
+{
+ return twl4030_usb_write(twl, ULPI_SET(reg), bits);
+}
+
+static inline int
+twl4030_usb_clear_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
+{
+ return twl4030_usb_write(twl, ULPI_CLR(reg), bits);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static bool twl4030_is_driving_vbus(struct twl4030_usb *twl)
+{
+ int ret;
+
+ ret = twl4030_usb_read(twl, PHY_CLK_CTRL_STS);
+ if (ret < 0 || !(ret & PHY_DPLL_CLK))
+ /*
+ * if clocks are off, registers are not updated,
+ * but we can assume we don't drive VBUS in this case
+ */
+ return false;
+
+ ret = twl4030_usb_read(twl, ULPI_OTG_CTRL);
+ if (ret < 0)
+ return false;
+
+ return (ret & (ULPI_OTG_DRVVBUS | ULPI_OTG_CHRGVBUS)) ? true : false;
+}
+
+static enum omap_musb_vbus_id_status
+ twl4030_usb_linkstat(struct twl4030_usb *twl)
+{
+ int status;
+ enum omap_musb_vbus_id_status linkstat = OMAP_MUSB_UNKNOWN;
+
+ twl->vbus_supplied = false;
+
+ /*
+ * For ID/VBUS sensing, see manual section 15.4.8 ...
+ * except when using only battery backup power, two
+ * comparators produce VBUS_PRES and ID_PRES signals,
+ * which don't match docs elsewhere. But ... BIT(7)
+ * and BIT(2) of STS_HW_CONDITIONS, respectively, do
+ * seem to match up. If either is true the USB_PRES
+ * signal is active, the OTG module is activated, and
+ * its interrupt may be raised (may wake the system).
+ */
+ status = twl4030_readb(twl, TWL_MODULE_PM_MASTER, STS_HW_CONDITIONS);
+ if (status < 0)
+ dev_err(twl->dev, "USB link status err %d\n", status);
+ else if (status & (BIT(7) | BIT(2))) {
+ if (status & BIT(7)) {
+ if (twl4030_is_driving_vbus(twl))
+ status &= ~BIT(7);
+ else
+ twl->vbus_supplied = true;
+ }
+
+ if (status & BIT(2))
+ linkstat = OMAP_MUSB_ID_GROUND;
+ else if (status & BIT(7))
+ linkstat = OMAP_MUSB_VBUS_VALID;
+ else
+ linkstat = OMAP_MUSB_VBUS_OFF;
+ } else {
+ if (twl->linkstat != OMAP_MUSB_UNKNOWN)
+ linkstat = OMAP_MUSB_VBUS_OFF;
+ }
+
+ dev_dbg(twl->dev, "HW_CONDITIONS 0x%02x/%d; link %d\n",
+ status, status, linkstat);
+
+ /* REVISIT this assumes host and peripheral controllers
+ * are registered, and that both are active...
+ */
+
+ return linkstat;
+}
+
+static void twl4030_usb_set_mode(struct twl4030_usb *twl, int mode)
+{
+ twl->usb_mode = mode;
+
+ switch (mode) {
+ case T2_USB_MODE_ULPI:
+ twl4030_usb_clear_bits(twl, ULPI_IFC_CTRL,
+ ULPI_IFC_CTRL_CARKITMODE);
+ twl4030_usb_set_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
+ twl4030_usb_clear_bits(twl, ULPI_FUNC_CTRL,
+ ULPI_FUNC_CTRL_XCVRSEL_MASK |
+ ULPI_FUNC_CTRL_OPMODE_MASK);
+ break;
+ case -1:
+ /* FIXME: power on defaults */
+ break;
+ default:
+ dev_err(twl->dev, "unsupported T2 transceiver mode %d\n",
+ mode);
+ break;
+ };
+}
+
+static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
+{
+ unsigned long timeout;
+ int val = twl4030_usb_read(twl, PHY_CLK_CTRL);
+
+ if (val >= 0) {
+ if (on) {
+ /* enable DPLL to access PHY registers over I2C */
+ val |= REQ_PHY_DPLL_CLK;
+ WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
+ (u8)val) < 0);
+
+ timeout = jiffies + HZ;
+ while (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
+ PHY_DPLL_CLK)
+ && time_before(jiffies, timeout))
+ udelay(10);
+ if (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
+ PHY_DPLL_CLK))
+ dev_err(twl->dev, "Timeout setting T2 HSUSB "
+ "PHY DPLL clock\n");
+ } else {
+ /* let ULPI control the DPLL clock */
+ val &= ~REQ_PHY_DPLL_CLK;
+ WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
+ (u8)val) < 0);
+ }
+ }
+}
+
+static void __twl4030_phy_power(struct twl4030_usb *twl, int on)
+{
+ u8 pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
+
+ if (on)
+ pwr &= ~PHY_PWR_PHYPWD;
+ else
+ pwr |= PHY_PWR_PHYPWD;
+
+ WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
+}
+
+static void twl4030_phy_power(struct twl4030_usb *twl, int on)
+{
+ int ret;
+
+ if (on) {
+ ret = regulator_enable(twl->usb3v1);
+ if (ret)
+ dev_err(twl->dev, "Failed to enable usb3v1\n");
+
+ ret = regulator_enable(twl->usb1v8);
+ if (ret)
+ dev_err(twl->dev, "Failed to enable usb1v8\n");
+
+ /*
+ * Disabling usb3v1 regulator (= writing 0 to VUSB3V1_DEV_GRP
+ * in twl4030) resets the VUSB_DEDICATED2 register. This reset
+ * enables VUSB3V1_SLEEP bit that remaps usb3v1 ACTIVE state to
+ * SLEEP. We work around this by clearing the bit after usv3v1
+ * is re-activated. This ensures that VUSB3V1 is really active.
+ */
+ twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
+
+ ret = regulator_enable(twl->usb1v5);
+ if (ret)
+ dev_err(twl->dev, "Failed to enable usb1v5\n");
+
+ __twl4030_phy_power(twl, 1);
+ twl4030_usb_write(twl, PHY_CLK_CTRL,
+ twl4030_usb_read(twl, PHY_CLK_CTRL) |
+ (PHY_CLK_CTRL_CLOCKGATING_EN |
+ PHY_CLK_CTRL_CLK32K_EN));
+ } else {
+ __twl4030_phy_power(twl, 0);
+ regulator_disable(twl->usb1v5);
+ regulator_disable(twl->usb1v8);
+ regulator_disable(twl->usb3v1);
+ }
+}
+
+static void twl4030_phy_suspend(struct twl4030_usb *twl, int controller_off)
+{
+ if (twl->asleep)
+ return;
+
+ twl4030_phy_power(twl, 0);
+ twl->asleep = 1;
+ dev_dbg(twl->dev, "%s\n", __func__);
+}
+
+static int twl4030_phy_power_off(struct phy *phy)
+{
+ struct twl4030_usb *twl = phy_get_drvdata(phy);
+
+ twl4030_phy_suspend(twl, 0);
+ return 0;
+}
+
+static void __twl4030_phy_resume(struct twl4030_usb *twl)
+{
+ twl4030_phy_power(twl, 1);
+ twl4030_i2c_access(twl, 1);
+ twl4030_usb_set_mode(twl, twl->usb_mode);
+ if (twl->usb_mode == T2_USB_MODE_ULPI)
+ twl4030_i2c_access(twl, 0);
+}
+
+static void twl4030_phy_resume(struct twl4030_usb *twl)
+{
+ if (!twl->asleep)
+ return;
+ __twl4030_phy_resume(twl);
+ twl->asleep = 0;
+ dev_dbg(twl->dev, "%s\n", __func__);
+
+ /*
+ * XXX When VBUS gets driven after musb goes to A mode,
+ * ID_PRES related interrupts no longer arrive, why?
+ * Register itself is updated fine though, so we must poll.
+ */
+ if (twl->linkstat == OMAP_MUSB_ID_GROUND) {
+ cancel_delayed_work(&twl->id_workaround_work);
+ schedule_delayed_work(&twl->id_workaround_work, HZ);
+ }
+}
+
+static int twl4030_phy_power_on(struct phy *phy)
+{
+ struct twl4030_usb *twl = phy_get_drvdata(phy);
+
+ twl4030_phy_resume(twl);
+ return 0;
+}
+
+static int twl4030_usb_ldo_init(struct twl4030_usb *twl)
+{
+ /* Enable writing to power configuration registers */
+ twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
+ TWL4030_PM_MASTER_PROTECT_KEY);
+
+ twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
+ TWL4030_PM_MASTER_PROTECT_KEY);
+
+ /* Keep VUSB3V1 LDO in sleep state until VBUS/ID change detected*/
+ /*twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
+
+ /* input to VUSB3V1 LDO is from VBAT, not VBUS */
+ twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
+
+ /* Initialize 3.1V regulator */
+ twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
+
+ twl->usb3v1 = devm_regulator_get(twl->dev, "usb3v1");
+ if (IS_ERR(twl->usb3v1))
+ return -ENODEV;
+
+ twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
+
+ /* Initialize 1.5V regulator */
+ twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
+
+ twl->usb1v5 = devm_regulator_get(twl->dev, "usb1v5");
+ if (IS_ERR(twl->usb1v5))
+ return -ENODEV;
+
+ twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
+
+ /* Initialize 1.8V regulator */
+ twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
+
+ twl->usb1v8 = devm_regulator_get(twl->dev, "usb1v8");
+ if (IS_ERR(twl->usb1v8))
+ return -ENODEV;
+
+ twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
+
+ /* disable access to power configuration registers */
+ twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
+ TWL4030_PM_MASTER_PROTECT_KEY);
+
+ return 0;
+}
+
+static ssize_t twl4030_usb_vbus_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct twl4030_usb *twl = dev_get_drvdata(dev);
+ unsigned long flags;
+ int ret = -EINVAL;
+
+ spin_lock_irqsave(&twl->lock, flags);
+ ret = sprintf(buf, "%s\n",
+ twl->vbus_supplied ? "on" : "off");
+ spin_unlock_irqrestore(&twl->lock, flags);
+
+ return ret;
+}
+static DEVICE_ATTR(vbus, 0444, twl4030_usb_vbus_show, NULL);
+
+static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
+{
+ struct twl4030_usb *twl = _twl;
+ enum omap_musb_vbus_id_status status;
+ bool status_changed = false;
+
+ status = twl4030_usb_linkstat(twl);
+
+ spin_lock_irq(&twl->lock);
+ if (status >= 0 && status != twl->linkstat) {
+ twl->linkstat = status;
+ status_changed = true;
+ }
+ spin_unlock_irq(&twl->lock);
+
+ if (status_changed) {
+ /* FIXME add a set_power() method so that B-devices can
+ * configure the charger appropriately. It's not always
+ * correct to consume VBUS power, and how much current to
+ * consume is a function of the USB configuration chosen
+ * by the host.
+ *
+ * REVISIT usb_gadget_vbus_connect(...) as needed, ditto
+ * its disconnect() sibling, when changing to/from the
+ * USB_LINK_VBUS state. musb_hdrc won't care until it
+ * starts to handle softconnect right.
+ */
+ omap_musb_mailbox(status);
+ }
+ sysfs_notify(&twl->dev->kobj, NULL, "vbus");
+
+ return IRQ_HANDLED;
+}
+
+static void twl4030_id_workaround_work(struct work_struct *work)
+{
+ struct twl4030_usb *twl = container_of(work, struct twl4030_usb,
+ id_workaround_work.work);
+ enum omap_musb_vbus_id_status status;
+ bool status_changed = false;
+
+ status = twl4030_usb_linkstat(twl);
+
+ spin_lock_irq(&twl->lock);
+ if (status >= 0 && status != twl->linkstat) {
+ twl->linkstat = status;
+ status_changed = true;
+ }
+ spin_unlock_irq(&twl->lock);
+
+ if (status_changed) {
+ dev_dbg(twl->dev, "handle missing status change to %d\n",
+ status);
+ omap_musb_mailbox(status);
+ }
+
+ /* don't schedule during sleep - irq works right then */
+ if (status == OMAP_MUSB_ID_GROUND && !twl->asleep) {
+ cancel_delayed_work(&twl->id_workaround_work);
+ schedule_delayed_work(&twl->id_workaround_work, HZ);
+ }
+}
+
+static int twl4030_usb_phy_init(struct usb_phy *phy)
+{
+ struct twl4030_usb *twl = phy_to_twl(phy);
+ enum omap_musb_vbus_id_status status;
+
+ /*
+ * Start in sleep state, we'll get called through set_suspend()
+ * callback when musb is runtime resumed and it's time to start.
+ */
+ __twl4030_phy_power(twl, 0);
+ twl->asleep = 1;
+
+ status = twl4030_usb_linkstat(twl);
+ twl->linkstat = status;
+
+ if (status == OMAP_MUSB_ID_GROUND || status == OMAP_MUSB_VBUS_VALID) {
+ omap_musb_mailbox(twl->linkstat);
+ twl4030_phy_resume(twl);
+ }
+
+ sysfs_notify(&twl->dev->kobj, NULL, "vbus");
+ return 0;
+}
+
+static int twl4030_phy_init(struct phy *phy)
+{
+ struct twl4030_usb *twl = phy_get_drvdata(phy);
+
+ return twl4030_usb_phy_init(&twl->phy);
+}
+
+static int twl4030_set_suspend(struct usb_phy *x, int suspend)
+{
+ struct twl4030_usb *twl = phy_to_twl(x);
+
+ if (suspend)
+ twl4030_phy_suspend(twl, 1);
+ else
+ twl4030_phy_resume(twl);
+
+ return 0;
+}
+
+static int twl4030_set_peripheral(struct usb_otg *otg,
+ struct usb_gadget *gadget)
+{
+ if (!otg)
+ return -ENODEV;
+
+ otg->gadget = gadget;
+ if (!gadget)
+ otg->phy->state = OTG_STATE_UNDEFINED;
+
+ return 0;
+}
+
+static int twl4030_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+ if (!otg)
+ return -ENODEV;
+
+ otg->host = host;
+ if (!host)
+ otg->phy->state = OTG_STATE_UNDEFINED;
+
+ return 0;
+}
+
+static const struct phy_ops ops = {
+ .init = twl4030_phy_init,
+ .power_on = twl4030_phy_power_on,
+ .power_off = twl4030_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int twl4030_usb_probe(struct platform_device *pdev)
+{
+ struct twl4030_usb_data *pdata = dev_get_platdata(&pdev->dev);
+ struct twl4030_usb *twl;
+ struct phy *phy;
+ int status, err;
+ struct usb_otg *otg;
+ struct device_node *np = pdev->dev.of_node;
+ struct phy_provider *phy_provider;
+ struct phy_init_data *init_data = NULL;
+
+ twl = devm_kzalloc(&pdev->dev, sizeof *twl, GFP_KERNEL);
+ if (!twl)
+ return -ENOMEM;
+
+ if (np)
+ of_property_read_u32(np, "usb_mode",
+ (enum twl4030_usb_mode *)&twl->usb_mode);
+ else if (pdata) {
+ twl->usb_mode = pdata->usb_mode;
+ init_data = pdata->init_data;
+ } else {
+ dev_err(&pdev->dev, "twl4030 initialized without pdata\n");
+ return -EINVAL;
+ }
+
+ otg = devm_kzalloc(&pdev->dev, sizeof *otg, GFP_KERNEL);
+ if (!otg)
+ return -ENOMEM;
+
+ twl->dev = &pdev->dev;
+ twl->irq = platform_get_irq(pdev, 0);
+ twl->vbus_supplied = false;
+ twl->asleep = 1;
+ twl->linkstat = OMAP_MUSB_UNKNOWN;
+
+ twl->phy.dev = twl->dev;
+ twl->phy.label = "twl4030";
+ twl->phy.otg = otg;
+ twl->phy.type = USB_PHY_TYPE_USB2;
+ twl->phy.set_suspend = twl4030_set_suspend;
+ twl->phy.init = twl4030_usb_phy_init;
+
+ otg->phy = &twl->phy;
+ otg->set_host = twl4030_set_host;
+ otg->set_peripheral = twl4030_set_peripheral;
+
+ phy_provider = devm_of_phy_provider_register(twl->dev,
+ of_phy_simple_xlate);
+ if (IS_ERR(phy_provider))
+ return PTR_ERR(phy_provider);
+
+ phy = devm_phy_create(twl->dev, &ops, init_data);
+ if (IS_ERR(phy)) {
+ dev_dbg(&pdev->dev, "Failed to create PHY\n");
+ return PTR_ERR(phy);
+ }
+
+ phy_set_drvdata(phy, twl);
+
+ /* init spinlock for workqueue */
+ spin_lock_init(&twl->lock);
+
+ INIT_DELAYED_WORK(&twl->id_workaround_work, twl4030_id_workaround_work);
+
+ err = twl4030_usb_ldo_init(twl);
+ if (err) {
+ dev_err(&pdev->dev, "ldo init failed\n");
+ return err;
+ }
+ usb_add_phy_dev(&twl->phy);
+
+ platform_set_drvdata(pdev, twl);
+ if (device_create_file(&pdev->dev, &dev_attr_vbus))
+ dev_warn(&pdev->dev, "could not create sysfs file\n");
+
+ /* Our job is to use irqs and status from the power module
+ * to keep the transceiver disabled when nothing's connected.
+ *
+ * FIXME we actually shouldn't start enabling it until the
+ * USB controller drivers have said they're ready, by calling
+ * set_host() and/or set_peripheral() ... OTG_capable boards
+ * need both handles, otherwise just one suffices.
+ */
+ twl->irq_enabled = true;
+ status = devm_request_threaded_irq(twl->dev, twl->irq, NULL,
+ twl4030_usb_irq, IRQF_TRIGGER_FALLING |
+ IRQF_TRIGGER_RISING | IRQF_ONESHOT, "twl4030_usb", twl);
+ if (status < 0) {
+ dev_dbg(&pdev->dev, "can't get IRQ %d, err %d\n",
+ twl->irq, status);
+ return status;
+ }
+
+ dev_info(&pdev->dev, "Initialized TWL4030 USB module\n");
+ return 0;
+}
+
+static int twl4030_usb_remove(struct platform_device *pdev)
+{
+ struct twl4030_usb *twl = platform_get_drvdata(pdev);
+ int val;
+
+ cancel_delayed_work(&twl->id_workaround_work);
+ device_remove_file(twl->dev, &dev_attr_vbus);
+
+ /* set transceiver mode to power on defaults */
+ twl4030_usb_set_mode(twl, -1);
+
+ /* autogate 60MHz ULPI clock,
+ * clear dpll clock request for i2c access,
+ * disable 32KHz
+ */
+ val = twl4030_usb_read(twl, PHY_CLK_CTRL);
+ if (val >= 0) {
+ val |= PHY_CLK_CTRL_CLOCKGATING_EN;
+ val &= ~(PHY_CLK_CTRL_CLK32K_EN | REQ_PHY_DPLL_CLK);
+ twl4030_usb_write(twl, PHY_CLK_CTRL, (u8)val);
+ }
+
+ /* disable complete OTG block */
+ twl4030_usb_clear_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
+
+ if (!twl->asleep)
+ twl4030_phy_power(twl, 0);
+
+ return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id twl4030_usb_id_table[] = {
+ { .compatible = "ti,twl4030-usb" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, twl4030_usb_id_table);
+#endif
+
+static struct platform_driver twl4030_usb_driver = {
+ .probe = twl4030_usb_probe,
+ .remove = twl4030_usb_remove,
+ .driver = {
+ .name = "twl4030_usb",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(twl4030_usb_id_table),
+ },
+};
+
+static int __init twl4030_usb_init(void)
+{
+ return platform_driver_register(&twl4030_usb_driver);
+}
+subsys_initcall(twl4030_usb_init);
+
+static void __exit twl4030_usb_exit(void)
+{
+ platform_driver_unregister(&twl4030_usb_driver);
+}
+module_exit(twl4030_usb_exit);
+
+MODULE_ALIAS("platform:twl4030_usb");
+MODULE_AUTHOR("Texas Instruments, Inc, Nokia Corporation");
+MODULE_DESCRIPTION("TWL4030 USB transceiver driver");
+MODULE_LICENSE("GPL");
Enable this to support Samsung USB 3.0 (Super Speed) phy controller
for samsung SoCs.
-config TWL4030_USB
- tristate "TWL4030 USB Transceiver Driver"
- depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
- select USB_PHY
- help
- Enable this to support the USB OTG transceiver on TWL4030
- family chips (including the TWL5030 and TPS659x0 devices).
- This transceiver supports high and full speed devices plus,
- in host mode, low speed.
-
config TWL6030_USB
tristate "TWL6030 USB Transceiver Driver"
depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
obj-$(CONFIG_SAMSUNG_USBPHY) += phy-samsung-usb.o
obj-$(CONFIG_SAMSUNG_USB2PHY) += phy-samsung-usb2.o
obj-$(CONFIG_SAMSUNG_USB3PHY) += phy-samsung-usb3.o
-obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
obj-$(CONFIG_TWL6030_USB) += phy-twl6030-usb.o
obj-$(CONFIG_USB_EHCI_TEGRA) += phy-tegra-usb.o
obj-$(CONFIG_USB_GPIO_VBUS) += phy-gpio-vbus-usb.o
+++ /dev/null
-/*
- * twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller
- *
- * Copyright (C) 2004-2007 Texas Instruments
- * Copyright (C) 2008 Nokia Corporation
- * Contact: Felipe Balbi <felipe.balbi@nokia.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * Current status:
- * - HS USB ULPI mode works.
- * - 3-pin mode support may be added in future.
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/spinlock.h>
-#include <linux/workqueue.h>
-#include <linux/io.h>
-#include <linux/delay.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/musb-omap.h>
-#include <linux/usb/ulpi.h>
-#include <linux/i2c/twl.h>
-#include <linux/regulator/consumer.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-
-/* Register defines */
-
-#define MCPC_CTRL 0x30
-#define MCPC_CTRL_RTSOL (1 << 7)
-#define MCPC_CTRL_EXTSWR (1 << 6)
-#define MCPC_CTRL_EXTSWC (1 << 5)
-#define MCPC_CTRL_VOICESW (1 << 4)
-#define MCPC_CTRL_OUT64K (1 << 3)
-#define MCPC_CTRL_RTSCTSSW (1 << 2)
-#define MCPC_CTRL_HS_UART (1 << 0)
-
-#define MCPC_IO_CTRL 0x33
-#define MCPC_IO_CTRL_MICBIASEN (1 << 5)
-#define MCPC_IO_CTRL_CTS_NPU (1 << 4)
-#define MCPC_IO_CTRL_RXD_PU (1 << 3)
-#define MCPC_IO_CTRL_TXDTYP (1 << 2)
-#define MCPC_IO_CTRL_CTSTYP (1 << 1)
-#define MCPC_IO_CTRL_RTSTYP (1 << 0)
-
-#define MCPC_CTRL2 0x36
-#define MCPC_CTRL2_MCPC_CK_EN (1 << 0)
-
-#define OTHER_FUNC_CTRL 0x80
-#define OTHER_FUNC_CTRL_BDIS_ACON_EN (1 << 4)
-#define OTHER_FUNC_CTRL_FIVEWIRE_MODE (1 << 2)
-
-#define OTHER_IFC_CTRL 0x83
-#define OTHER_IFC_CTRL_OE_INT_EN (1 << 6)
-#define OTHER_IFC_CTRL_CEA2011_MODE (1 << 5)
-#define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN (1 << 4)
-#define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT (1 << 3)
-#define OTHER_IFC_CTRL_HIZ_ULPI (1 << 2)
-#define OTHER_IFC_CTRL_ALT_INT_REROUTE (1 << 0)
-
-#define OTHER_INT_EN_RISE 0x86
-#define OTHER_INT_EN_FALL 0x89
-#define OTHER_INT_STS 0x8C
-#define OTHER_INT_LATCH 0x8D
-#define OTHER_INT_VB_SESS_VLD (1 << 7)
-#define OTHER_INT_DM_HI (1 << 6) /* not valid for "latch" reg */
-#define OTHER_INT_DP_HI (1 << 5) /* not valid for "latch" reg */
-#define OTHER_INT_BDIS_ACON (1 << 3) /* not valid for "fall" regs */
-#define OTHER_INT_MANU (1 << 1)
-#define OTHER_INT_ABNORMAL_STRESS (1 << 0)
-
-#define ID_STATUS 0x96
-#define ID_RES_FLOAT (1 << 4)
-#define ID_RES_440K (1 << 3)
-#define ID_RES_200K (1 << 2)
-#define ID_RES_102K (1 << 1)
-#define ID_RES_GND (1 << 0)
-
-#define POWER_CTRL 0xAC
-#define POWER_CTRL_OTG_ENAB (1 << 5)
-
-#define OTHER_IFC_CTRL2 0xAF
-#define OTHER_IFC_CTRL2_ULPI_STP_LOW (1 << 4)
-#define OTHER_IFC_CTRL2_ULPI_TXEN_POL (1 << 3)
-#define OTHER_IFC_CTRL2_ULPI_4PIN_2430 (1 << 2)
-#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK (3 << 0) /* bits 0 and 1 */
-#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N (0 << 0)
-#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N (1 << 0)
-
-#define REG_CTRL_EN 0xB2
-#define REG_CTRL_ERROR 0xB5
-#define ULPI_I2C_CONFLICT_INTEN (1 << 0)
-
-#define OTHER_FUNC_CTRL2 0xB8
-#define OTHER_FUNC_CTRL2_VBAT_TIMER_EN (1 << 0)
-
-/* following registers do not have separate _clr and _set registers */
-#define VBUS_DEBOUNCE 0xC0
-#define ID_DEBOUNCE 0xC1
-#define VBAT_TIMER 0xD3
-#define PHY_PWR_CTRL 0xFD
-#define PHY_PWR_PHYPWD (1 << 0)
-#define PHY_CLK_CTRL 0xFE
-#define PHY_CLK_CTRL_CLOCKGATING_EN (1 << 2)
-#define PHY_CLK_CTRL_CLK32K_EN (1 << 1)
-#define REQ_PHY_DPLL_CLK (1 << 0)
-#define PHY_CLK_CTRL_STS 0xFF
-#define PHY_DPLL_CLK (1 << 0)
-
-/* In module TWL_MODULE_PM_MASTER */
-#define STS_HW_CONDITIONS 0x0F
-
-/* In module TWL_MODULE_PM_RECEIVER */
-#define VUSB_DEDICATED1 0x7D
-#define VUSB_DEDICATED2 0x7E
-#define VUSB1V5_DEV_GRP 0x71
-#define VUSB1V5_TYPE 0x72
-#define VUSB1V5_REMAP 0x73
-#define VUSB1V8_DEV_GRP 0x74
-#define VUSB1V8_TYPE 0x75
-#define VUSB1V8_REMAP 0x76
-#define VUSB3V1_DEV_GRP 0x77
-#define VUSB3V1_TYPE 0x78
-#define VUSB3V1_REMAP 0x79
-
-/* In module TWL4030_MODULE_INTBR */
-#define PMBR1 0x0D
-#define GPIO_USB_4PIN_ULPI_2430C (3 << 0)
-
-struct twl4030_usb {
- struct usb_phy phy;
- struct device *dev;
-
- /* TWL4030 internal USB regulator supplies */
- struct regulator *usb1v5;
- struct regulator *usb1v8;
- struct regulator *usb3v1;
-
- /* for vbus reporting with irqs disabled */
- spinlock_t lock;
-
- /* pin configuration */
- enum twl4030_usb_mode usb_mode;
-
- int irq;
- enum omap_musb_vbus_id_status linkstat;
- bool vbus_supplied;
- u8 asleep;
- bool irq_enabled;
-
- struct delayed_work id_workaround_work;
-};
-
-/* internal define on top of container_of */
-#define phy_to_twl(x) container_of((x), struct twl4030_usb, phy)
-
-/*-------------------------------------------------------------------------*/
-
-static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
- u8 module, u8 data, u8 address)
-{
- u8 check;
-
- if ((twl_i2c_write_u8(module, data, address) >= 0) &&
- (twl_i2c_read_u8(module, &check, address) >= 0) &&
- (check == data))
- return 0;
- dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
- 1, module, address, check, data);
-
- /* Failed once: Try again */
- if ((twl_i2c_write_u8(module, data, address) >= 0) &&
- (twl_i2c_read_u8(module, &check, address) >= 0) &&
- (check == data))
- return 0;
- dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
- 2, module, address, check, data);
-
- /* Failed again: Return error */
- return -EBUSY;
-}
-
-#define twl4030_usb_write_verify(twl, address, data) \
- twl4030_i2c_write_u8_verify(twl, TWL_MODULE_USB, (data), (address))
-
-static inline int twl4030_usb_write(struct twl4030_usb *twl,
- u8 address, u8 data)
-{
- int ret = 0;
-
- ret = twl_i2c_write_u8(TWL_MODULE_USB, data, address);
- if (ret < 0)
- dev_dbg(twl->dev,
- "TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
- return ret;
-}
-
-static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8 address)
-{
- u8 data;
- int ret = 0;
-
- ret = twl_i2c_read_u8(module, &data, address);
- if (ret >= 0)
- ret = data;
- else
- dev_dbg(twl->dev,
- "TWL4030:readb[0x%x,0x%x] Error %d\n",
- module, address, ret);
-
- return ret;
-}
-
-static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
-{
- return twl4030_readb(twl, TWL_MODULE_USB, address);
-}
-
-/*-------------------------------------------------------------------------*/
-
-static inline int
-twl4030_usb_set_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
-{
- return twl4030_usb_write(twl, ULPI_SET(reg), bits);
-}
-
-static inline int
-twl4030_usb_clear_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
-{
- return twl4030_usb_write(twl, ULPI_CLR(reg), bits);
-}
-
-/*-------------------------------------------------------------------------*/
-
-static bool twl4030_is_driving_vbus(struct twl4030_usb *twl)
-{
- int ret;
-
- ret = twl4030_usb_read(twl, PHY_CLK_CTRL_STS);
- if (ret < 0 || !(ret & PHY_DPLL_CLK))
- /*
- * if clocks are off, registers are not updated,
- * but we can assume we don't drive VBUS in this case
- */
- return false;
-
- ret = twl4030_usb_read(twl, ULPI_OTG_CTRL);
- if (ret < 0)
- return false;
-
- return (ret & (ULPI_OTG_DRVVBUS | ULPI_OTG_CHRGVBUS)) ? true : false;
-}
-
-static enum omap_musb_vbus_id_status
- twl4030_usb_linkstat(struct twl4030_usb *twl)
-{
- int status;
- enum omap_musb_vbus_id_status linkstat = OMAP_MUSB_UNKNOWN;
-
- twl->vbus_supplied = false;
-
- /*
- * For ID/VBUS sensing, see manual section 15.4.8 ...
- * except when using only battery backup power, two
- * comparators produce VBUS_PRES and ID_PRES signals,
- * which don't match docs elsewhere. But ... BIT(7)
- * and BIT(2) of STS_HW_CONDITIONS, respectively, do
- * seem to match up. If either is true the USB_PRES
- * signal is active, the OTG module is activated, and
- * its interrupt may be raised (may wake the system).
- */
- status = twl4030_readb(twl, TWL_MODULE_PM_MASTER, STS_HW_CONDITIONS);
- if (status < 0)
- dev_err(twl->dev, "USB link status err %d\n", status);
- else if (status & (BIT(7) | BIT(2))) {
- if (status & BIT(7)) {
- if (twl4030_is_driving_vbus(twl))
- status &= ~BIT(7);
- else
- twl->vbus_supplied = true;
- }
-
- if (status & BIT(2))
- linkstat = OMAP_MUSB_ID_GROUND;
- else if (status & BIT(7))
- linkstat = OMAP_MUSB_VBUS_VALID;
- else
- linkstat = OMAP_MUSB_VBUS_OFF;
- } else {
- if (twl->linkstat != OMAP_MUSB_UNKNOWN)
- linkstat = OMAP_MUSB_VBUS_OFF;
- }
-
- dev_dbg(twl->dev, "HW_CONDITIONS 0x%02x/%d; link %d\n",
- status, status, linkstat);
-
- /* REVISIT this assumes host and peripheral controllers
- * are registered, and that both are active...
- */
-
- return linkstat;
-}
-
-static void twl4030_usb_set_mode(struct twl4030_usb *twl, int mode)
-{
- twl->usb_mode = mode;
-
- switch (mode) {
- case T2_USB_MODE_ULPI:
- twl4030_usb_clear_bits(twl, ULPI_IFC_CTRL,
- ULPI_IFC_CTRL_CARKITMODE);
- twl4030_usb_set_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
- twl4030_usb_clear_bits(twl, ULPI_FUNC_CTRL,
- ULPI_FUNC_CTRL_XCVRSEL_MASK |
- ULPI_FUNC_CTRL_OPMODE_MASK);
- break;
- case -1:
- /* FIXME: power on defaults */
- break;
- default:
- dev_err(twl->dev, "unsupported T2 transceiver mode %d\n",
- mode);
- break;
- };
-}
-
-static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
-{
- unsigned long timeout;
- int val = twl4030_usb_read(twl, PHY_CLK_CTRL);
-
- if (val >= 0) {
- if (on) {
- /* enable DPLL to access PHY registers over I2C */
- val |= REQ_PHY_DPLL_CLK;
- WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
- (u8)val) < 0);
-
- timeout = jiffies + HZ;
- while (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
- PHY_DPLL_CLK)
- && time_before(jiffies, timeout))
- udelay(10);
- if (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
- PHY_DPLL_CLK))
- dev_err(twl->dev, "Timeout setting T2 HSUSB "
- "PHY DPLL clock\n");
- } else {
- /* let ULPI control the DPLL clock */
- val &= ~REQ_PHY_DPLL_CLK;
- WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
- (u8)val) < 0);
- }
- }
-}
-
-static void __twl4030_phy_power(struct twl4030_usb *twl, int on)
-{
- u8 pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
-
- if (on)
- pwr &= ~PHY_PWR_PHYPWD;
- else
- pwr |= PHY_PWR_PHYPWD;
-
- WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
-}
-
-static void twl4030_phy_power(struct twl4030_usb *twl, int on)
-{
- int ret;
-
- if (on) {
- ret = regulator_enable(twl->usb3v1);
- if (ret)
- dev_err(twl->dev, "Failed to enable usb3v1\n");
-
- ret = regulator_enable(twl->usb1v8);
- if (ret)
- dev_err(twl->dev, "Failed to enable usb1v8\n");
-
- /*
- * Disabling usb3v1 regulator (= writing 0 to VUSB3V1_DEV_GRP
- * in twl4030) resets the VUSB_DEDICATED2 register. This reset
- * enables VUSB3V1_SLEEP bit that remaps usb3v1 ACTIVE state to
- * SLEEP. We work around this by clearing the bit after usv3v1
- * is re-activated. This ensures that VUSB3V1 is really active.
- */
- twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
-
- ret = regulator_enable(twl->usb1v5);
- if (ret)
- dev_err(twl->dev, "Failed to enable usb1v5\n");
-
- __twl4030_phy_power(twl, 1);
- twl4030_usb_write(twl, PHY_CLK_CTRL,
- twl4030_usb_read(twl, PHY_CLK_CTRL) |
- (PHY_CLK_CTRL_CLOCKGATING_EN |
- PHY_CLK_CTRL_CLK32K_EN));
- } else {
- __twl4030_phy_power(twl, 0);
- regulator_disable(twl->usb1v5);
- regulator_disable(twl->usb1v8);
- regulator_disable(twl->usb3v1);
- }
-}
-
-static void twl4030_phy_suspend(struct twl4030_usb *twl, int controller_off)
-{
- if (twl->asleep)
- return;
-
- twl4030_phy_power(twl, 0);
- twl->asleep = 1;
- dev_dbg(twl->dev, "%s\n", __func__);
-}
-
-static void __twl4030_phy_resume(struct twl4030_usb *twl)
-{
- twl4030_phy_power(twl, 1);
- twl4030_i2c_access(twl, 1);
- twl4030_usb_set_mode(twl, twl->usb_mode);
- if (twl->usb_mode == T2_USB_MODE_ULPI)
- twl4030_i2c_access(twl, 0);
-}
-
-static void twl4030_phy_resume(struct twl4030_usb *twl)
-{
- if (!twl->asleep)
- return;
- __twl4030_phy_resume(twl);
- twl->asleep = 0;
- dev_dbg(twl->dev, "%s\n", __func__);
-
- /*
- * XXX When VBUS gets driven after musb goes to A mode,
- * ID_PRES related interrupts no longer arrive, why?
- * Register itself is updated fine though, so we must poll.
- */
- if (twl->linkstat == OMAP_MUSB_ID_GROUND) {
- cancel_delayed_work(&twl->id_workaround_work);
- schedule_delayed_work(&twl->id_workaround_work, HZ);
- }
-}
-
-static int twl4030_usb_ldo_init(struct twl4030_usb *twl)
-{
- /* Enable writing to power configuration registers */
- twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
- TWL4030_PM_MASTER_PROTECT_KEY);
-
- twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
- TWL4030_PM_MASTER_PROTECT_KEY);
-
- /* Keep VUSB3V1 LDO in sleep state until VBUS/ID change detected*/
- /*twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
-
- /* input to VUSB3V1 LDO is from VBAT, not VBUS */
- twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
-
- /* Initialize 3.1V regulator */
- twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
-
- twl->usb3v1 = devm_regulator_get(twl->dev, "usb3v1");
- if (IS_ERR(twl->usb3v1))
- return -ENODEV;
-
- twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
-
- /* Initialize 1.5V regulator */
- twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
-
- twl->usb1v5 = devm_regulator_get(twl->dev, "usb1v5");
- if (IS_ERR(twl->usb1v5))
- return -ENODEV;
-
- twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
-
- /* Initialize 1.8V regulator */
- twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
-
- twl->usb1v8 = devm_regulator_get(twl->dev, "usb1v8");
- if (IS_ERR(twl->usb1v8))
- return -ENODEV;
-
- twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
-
- /* disable access to power configuration registers */
- twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
- TWL4030_PM_MASTER_PROTECT_KEY);
-
- return 0;
-}
-
-static ssize_t twl4030_usb_vbus_show(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct twl4030_usb *twl = dev_get_drvdata(dev);
- unsigned long flags;
- int ret = -EINVAL;
-
- spin_lock_irqsave(&twl->lock, flags);
- ret = sprintf(buf, "%s\n",
- twl->vbus_supplied ? "on" : "off");
- spin_unlock_irqrestore(&twl->lock, flags);
-
- return ret;
-}
-static DEVICE_ATTR(vbus, 0444, twl4030_usb_vbus_show, NULL);
-
-static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
-{
- struct twl4030_usb *twl = _twl;
- enum omap_musb_vbus_id_status status;
- bool status_changed = false;
-
- status = twl4030_usb_linkstat(twl);
-
- spin_lock_irq(&twl->lock);
- if (status >= 0 && status != twl->linkstat) {
- twl->linkstat = status;
- status_changed = true;
- }
- spin_unlock_irq(&twl->lock);
-
- if (status_changed) {
- /* FIXME add a set_power() method so that B-devices can
- * configure the charger appropriately. It's not always
- * correct to consume VBUS power, and how much current to
- * consume is a function of the USB configuration chosen
- * by the host.
- *
- * REVISIT usb_gadget_vbus_connect(...) as needed, ditto
- * its disconnect() sibling, when changing to/from the
- * USB_LINK_VBUS state. musb_hdrc won't care until it
- * starts to handle softconnect right.
- */
- omap_musb_mailbox(status);
- }
- sysfs_notify(&twl->dev->kobj, NULL, "vbus");
-
- return IRQ_HANDLED;
-}
-
-static void twl4030_id_workaround_work(struct work_struct *work)
-{
- struct twl4030_usb *twl = container_of(work, struct twl4030_usb,
- id_workaround_work.work);
- enum omap_musb_vbus_id_status status;
- bool status_changed = false;
-
- status = twl4030_usb_linkstat(twl);
-
- spin_lock_irq(&twl->lock);
- if (status >= 0 && status != twl->linkstat) {
- twl->linkstat = status;
- status_changed = true;
- }
- spin_unlock_irq(&twl->lock);
-
- if (status_changed) {
- dev_dbg(twl->dev, "handle missing status change to %d\n",
- status);
- omap_musb_mailbox(status);
- }
-
- /* don't schedule during sleep - irq works right then */
- if (status == OMAP_MUSB_ID_GROUND && !twl->asleep) {
- cancel_delayed_work(&twl->id_workaround_work);
- schedule_delayed_work(&twl->id_workaround_work, HZ);
- }
-}
-
-static int twl4030_usb_phy_init(struct usb_phy *phy)
-{
- struct twl4030_usb *twl = phy_to_twl(phy);
- enum omap_musb_vbus_id_status status;
-
- /*
- * Start in sleep state, we'll get called through set_suspend()
- * callback when musb is runtime resumed and it's time to start.
- */
- __twl4030_phy_power(twl, 0);
- twl->asleep = 1;
-
- status = twl4030_usb_linkstat(twl);
- twl->linkstat = status;
-
- if (status == OMAP_MUSB_ID_GROUND || status == OMAP_MUSB_VBUS_VALID)
- omap_musb_mailbox(twl->linkstat);
-
- sysfs_notify(&twl->dev->kobj, NULL, "vbus");
- return 0;
-}
-
-static int twl4030_set_suspend(struct usb_phy *x, int suspend)
-{
- struct twl4030_usb *twl = phy_to_twl(x);
-
- if (suspend)
- twl4030_phy_suspend(twl, 1);
- else
- twl4030_phy_resume(twl);
-
- return 0;
-}
-
-static int twl4030_set_peripheral(struct usb_otg *otg,
- struct usb_gadget *gadget)
-{
- if (!otg)
- return -ENODEV;
-
- otg->gadget = gadget;
- if (!gadget)
- otg->phy->state = OTG_STATE_UNDEFINED;
-
- return 0;
-}
-
-static int twl4030_set_host(struct usb_otg *otg, struct usb_bus *host)
-{
- if (!otg)
- return -ENODEV;
-
- otg->host = host;
- if (!host)
- otg->phy->state = OTG_STATE_UNDEFINED;
-
- return 0;
-}
-
-static int twl4030_usb_probe(struct platform_device *pdev)
-{
- struct twl4030_usb_data *pdata = dev_get_platdata(&pdev->dev);
- struct twl4030_usb *twl;
- int status, err;
- struct usb_otg *otg;
- struct device_node *np = pdev->dev.of_node;
-
- twl = devm_kzalloc(&pdev->dev, sizeof *twl, GFP_KERNEL);
- if (!twl)
- return -ENOMEM;
-
- if (np)
- of_property_read_u32(np, "usb_mode",
- (enum twl4030_usb_mode *)&twl->usb_mode);
- else if (pdata)
- twl->usb_mode = pdata->usb_mode;
- else {
- dev_err(&pdev->dev, "twl4030 initialized without pdata\n");
- return -EINVAL;
- }
-
- otg = devm_kzalloc(&pdev->dev, sizeof *otg, GFP_KERNEL);
- if (!otg)
- return -ENOMEM;
-
- twl->dev = &pdev->dev;
- twl->irq = platform_get_irq(pdev, 0);
- twl->vbus_supplied = false;
- twl->asleep = 1;
- twl->linkstat = OMAP_MUSB_UNKNOWN;
-
- twl->phy.dev = twl->dev;
- twl->phy.label = "twl4030";
- twl->phy.otg = otg;
- twl->phy.type = USB_PHY_TYPE_USB2;
- twl->phy.set_suspend = twl4030_set_suspend;
- twl->phy.init = twl4030_usb_phy_init;
-
- otg->phy = &twl->phy;
- otg->set_host = twl4030_set_host;
- otg->set_peripheral = twl4030_set_peripheral;
-
- /* init spinlock for workqueue */
- spin_lock_init(&twl->lock);
-
- INIT_DELAYED_WORK(&twl->id_workaround_work, twl4030_id_workaround_work);
-
- err = twl4030_usb_ldo_init(twl);
- if (err) {
- dev_err(&pdev->dev, "ldo init failed\n");
- return err;
- }
- usb_add_phy_dev(&twl->phy);
-
- platform_set_drvdata(pdev, twl);
- if (device_create_file(&pdev->dev, &dev_attr_vbus))
- dev_warn(&pdev->dev, "could not create sysfs file\n");
-
- /* Our job is to use irqs and status from the power module
- * to keep the transceiver disabled when nothing's connected.
- *
- * FIXME we actually shouldn't start enabling it until the
- * USB controller drivers have said they're ready, by calling
- * set_host() and/or set_peripheral() ... OTG_capable boards
- * need both handles, otherwise just one suffices.
- */
- twl->irq_enabled = true;
- status = devm_request_threaded_irq(twl->dev, twl->irq, NULL,
- twl4030_usb_irq, IRQF_TRIGGER_FALLING |
- IRQF_TRIGGER_RISING | IRQF_ONESHOT, "twl4030_usb", twl);
- if (status < 0) {
- dev_dbg(&pdev->dev, "can't get IRQ %d, err %d\n",
- twl->irq, status);
- return status;
- }
-
- dev_info(&pdev->dev, "Initialized TWL4030 USB module\n");
- return 0;
-}
-
-static int twl4030_usb_remove(struct platform_device *pdev)
-{
- struct twl4030_usb *twl = platform_get_drvdata(pdev);
- int val;
-
- cancel_delayed_work(&twl->id_workaround_work);
- device_remove_file(twl->dev, &dev_attr_vbus);
-
- /* set transceiver mode to power on defaults */
- twl4030_usb_set_mode(twl, -1);
-
- /* autogate 60MHz ULPI clock,
- * clear dpll clock request for i2c access,
- * disable 32KHz
- */
- val = twl4030_usb_read(twl, PHY_CLK_CTRL);
- if (val >= 0) {
- val |= PHY_CLK_CTRL_CLOCKGATING_EN;
- val &= ~(PHY_CLK_CTRL_CLK32K_EN | REQ_PHY_DPLL_CLK);
- twl4030_usb_write(twl, PHY_CLK_CTRL, (u8)val);
- }
-
- /* disable complete OTG block */
- twl4030_usb_clear_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
-
- if (!twl->asleep)
- twl4030_phy_power(twl, 0);
-
- return 0;
-}
-
-#ifdef CONFIG_OF
-static const struct of_device_id twl4030_usb_id_table[] = {
- { .compatible = "ti,twl4030-usb" },
- {}
-};
-MODULE_DEVICE_TABLE(of, twl4030_usb_id_table);
-#endif
-
-static struct platform_driver twl4030_usb_driver = {
- .probe = twl4030_usb_probe,
- .remove = twl4030_usb_remove,
- .driver = {
- .name = "twl4030_usb",
- .owner = THIS_MODULE,
- .of_match_table = of_match_ptr(twl4030_usb_id_table),
- },
-};
-
-static int __init twl4030_usb_init(void)
-{
- return platform_driver_register(&twl4030_usb_driver);
-}
-subsys_initcall(twl4030_usb_init);
-
-static void __exit twl4030_usb_exit(void)
-{
- platform_driver_unregister(&twl4030_usb_driver);
-}
-module_exit(twl4030_usb_exit);
-
-MODULE_ALIAS("platform:twl4030_usb");
-MODULE_AUTHOR("Texas Instruments, Inc, Nokia Corporation");
-MODULE_DESCRIPTION("TWL4030 USB transceiver driver");
-MODULE_LICENSE("GPL");
#define __TWL_H_
#include <linux/types.h>
+#include <linux/phy/phy.h>
#include <linux/input/matrix_keypad.h>
/*
struct twl4030_usb_data {
enum twl4030_usb_mode usb_mode;
unsigned long features;
+ struct phy_init_data *init_data;
int (*phy_init)(struct device *dev);
int (*phy_exit)(struct device *dev);
projects / platform / kernel / linux-rpi.git / commitdiff