--- /dev/null
+* Advanced Interrupt Controller (AIC)
+
+Required properties:
+- compatible: Should be "atmel,<chip>-aic"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- interrupt-parent: For single AIC system, it is an empty property.
+- #interrupt-cells: The number of cells to define the interrupts. It sould be 2.
+ The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet).
+ The second cell is used to specify flags:
+ bits[3:0] trigger type and level flags:
+ 1 = low-to-high edge triggered.
+ 2 = high-to-low edge triggered.
+ 4 = active high level-sensitive.
+ 8 = active low level-sensitive.
+ Valid combinations are 1, 2, 3, 4, 8.
+ Default flag for internal sources should be set to 4 (active high).
+- reg: Should contain AIC registers location and length
+
+Examples:
+ /*
+ * AIC
+ */
+ aic: interrupt-controller@fffff000 {
+ compatible = "atmel,at91rm9200-aic";
+ interrupt-controller;
+ interrupt-parent;
+ #interrupt-cells = <2>;
+ reg = <0xfffff000 0x200>;
+ };
+
+ /*
+ * An interrupt generating device that is wired to an AIC.
+ */
+ dma: dma-controller@ffffec00 {
+ compatible = "atmel,at91sam9g45-dma";
+ reg = <0xffffec00 0x200>;
+ interrupts = <21 4>;
+ };
--- /dev/null
+Atmel AT91 device tree bindings.
+================================
+
+PIT Timer required properties:
+- compatible: Should be "atmel,at91sam9260-pit"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt for the PIT which is the IRQ line
+ shared across all System Controller members.
+
+TC/TCLIB Timer required properties:
+- compatible: Should be "atmel,<chip>-pit".
+ <chip> can be "at91rm9200" or "at91sam9x5"
+- reg: Should contain registers location and length
+- interrupts: Should contain all interrupts for the TC block
+ Note that you can specify several interrupt cells if the TC
+ block has one interrupt per channel.
+
+Examples:
+
+One interrupt per TC block:
+ tcb0: timer@fff7c000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfff7c000 0x100>;
+ interrupts = <18 4>;
+ };
+
+One interrupt per TC channel in a TC block:
+ tcb1: timer@fffdc000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfffdc000 0x100>;
+ interrupts = <26 4 27 4 28 4>;
+ };
i.MX6 Quad SABRE Lite Board
Required root node properties:
- compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
+
+Generic i.MX boards
+-------------------
+
+No iomux setup is done for these boards, so this must have been configured
+by the bootloader for boards to work with the generic bindings.
+
+i.MX27 generic board
+Required root node properties:
+ - compatible = "fsl,imx27";
+
+i.MX51 generic board
+Required root node properties:
+ - compatible = "fsl,imx51";
+
+i.MX53 generic board
+Required root node properties:
+ - compatible = "fsl,imx53";
+
+i.MX6q generic board
+Required root node properties:
+ - compatible = "fsl,imx6q";
--- /dev/null
+Marvell Platforms Device Tree Bindings
+----------------------------------------------------
+
+PXA168 Aspenite Board
+Required root node properties:
+ - compatible = "mrvl,pxa168-aspenite", "mrvl,pxa168";
--- /dev/null
+* OMAP Interrupt Controller
+
+OMAP2/3 are using a TI interrupt controller that can support several
+configurable number of interrupts.
+
+Main node required properties:
+
+- compatible : should be:
+ "ti,omap2-intc"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+ interrupt source. The type shall be a <u32> and the value shall be 1.
+
+ The cell contains the interrupt number in the range [0-128].
+- ti,intc-size: Number of interrupts handled by the interrupt controller.
+- reg: physical base address and size of the intc registers map.
+
+Example:
+
+ intc: interrupt-controller@1 {
+ compatible = "ti,omap2-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ ti,intc-size = <96>;
+ reg = <0x48200000 0x1000>;
+ };
+
--- /dev/null
+ARM Versatile Express boards family
+-----------------------------------
+
+ARM's Versatile Express platform consists of a motherboard and one
+or more daughterboards (tiles). The motherboard provides a set of
+peripherals. Processor and RAM "live" on the tiles.
+
+The motherboard and each core tile should be described by a separate
+Device Tree source file, with the tile's description including
+the motherboard file using a /include/ directive. As the motherboard
+can be initialized in one of two different configurations ("memory
+maps"), care must be taken to include the correct one.
+
+Required properties in the root node:
+- compatible value:
+ compatible = "arm,vexpress,<model>", "arm,vexpress";
+ where <model> is the full tile model name (as used in the tile's
+ Technical Reference Manual), eg.:
+ - for Coretile Express A5x2 (V2P-CA5s):
+ compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress";
+ - for Coretile Express A9x4 (V2P-CA9):
+ compatible = "arm,vexpress,v2p-ca9", "arm,vexpress";
+ If a tile comes in several variants or can be used in more then one
+ configuration, the compatible value should be:
+ compatible = "arm,vexpress,<model>,<variant>", \
+ "arm,vexpress,<model>", "arm,vexpress";
+ eg:
+ - Coretile Express A15x2 (V2P-CA15) with Tech Chip 1:
+ compatible = "arm,vexpress,v2p-ca15,tc1", \
+ "arm,vexpress,v2p-ca15", "arm,vexpress";
+ - LogicTile Express 13MG (V2F-2XV6) running Cortex-A7 (3 cores) SMM:
+ compatible = "arm,vexpress,v2f-2xv6,ca7x3", \
+ "arm,vexpress,v2f-2xv6", "arm,vexpress";
+
+Optional properties in the root node:
+- tile model name (use name from the tile's Technical Reference
+ Manual, eg. "V2P-CA5s")
+ model = "<model>";
+- tile's HBI number (unique ARM's board model ID, visible on the
+ PCB's silkscreen) in hexadecimal transcription:
+ arm,hbi = <0xhbi>
+ eg:
+ - for Coretile Express A5x2 (V2P-CA5s) HBI-0191:
+ arm,hbi = <0x191>;
+ - Coretile Express A9x4 (V2P-CA9) HBI-0225:
+ arm,hbi = <0x225>;
+
+Top-level standard "cpus" node is required. It must contain a node
+with device_type = "cpu" property for every available core, eg.:
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a5";
+ reg = <0>;
+ };
+ };
+
+The motherboard description file provides a single "motherboard" node
+using 2 address cells corresponding to the Static Memory Bus used
+between the motherboard and the tile. The first cell defines the Chip
+Select (CS) line number, the second cell address offset within the CS.
+All interrupt lines between the motherboard and the tile are active
+high and are described using single cell.
+
+Optional properties of the "motherboard" node:
+- motherboard's memory map variant:
+ arm,v2m-memory-map = "<name>";
+ where name is one of:
+ - "rs1" - for RS1 map (i.a. peripherals on CS3); this map is also
+ referred to as "ARM Cortex-A Series memory map":
+ arm,v2m-memory-map = "rs1";
+ When this property is missing, the motherboard is using the original
+ memory map (also known as the "Legacy memory map", primarily used
+ with the original CoreTile Express A9x4) with peripherals on CS7.
+
+Motherboard .dtsi files provide a set of labelled peripherals that
+can be used to obtain required phandle in the tile's "aliases" node:
+- UARTs, note that the numbers correspond to the physical connectors
+ on the motherboard's back panel:
+ v2m_serial0, v2m_serial1, v2m_serial2 and v2m_serial3
+- I2C controllers:
+ v2m_i2c_dvi and v2m_i2c_pcie
+- SP804 timers:
+ v2m_timer01 and v2m_timer23
+
+Current Linux implementation requires a "arm,v2m_timer" alias
+pointing at one of the motherboard's SP804 timers, if it is to be
+used as the system timer. This alias should be defined in the
+motherboard files.
+
+The tile description must define "ranges", "interrupt-map-mask" and
+"interrupt-map" properties to translate the motherboard's address
+and interrupt space into one used by the tile's processor.
+
+Abbreviated example:
+
+/dts-v1/;
+
+/ {
+ model = "V2P-CA5s";
+ arm,hbi = <0x225>;
+ compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ chosen { };
+
+ aliases {
+ serial0 = &v2m_serial0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a5";
+ reg = <0>;
+ };
+ };
+
+ gic: interrupt-controller@2c001000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x2c001000 0x1000>,
+ <0x2c000100 0x100>;
+ };
+
+ motherboard {
+ /* CS0 is visible at 0x08000000 */
+ ranges = <0 0 0x08000000 0x04000000>;
+ interrupt-map-mask = <0 0 63>;
+ /* Active high IRQ 0 is connected to GIC's SPI0 */
+ interrupt-map = <0 0 0 &gic 0 0 4>;
+ };
+};
+
+/include/ "vexpress-v2m-rs1.dtsi"
--- /dev/null
+* Atmel GPIO controller (PIO)
+
+Required properties:
+- compatible: "atmel,<chip>-gpio", where <chip> is at91rm9200 or at91sam9x5.
+- reg: Should contain GPIO controller registers location and length
+- interrupts: Should be the port interrupt shared by all the pins.
+- #gpio-cells: Should be two. The first cell is the pin number and
+ the second cell is used to specify optional parameters (currently
+ unused).
+- gpio-controller: Marks the device node as a GPIO controller.
+
+Example:
+ pioA: gpio@fffff200 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff200 0x100>;
+ interrupts = <2 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
--- /dev/null
+* Marvell PXA GPIO controller
+
+Required properties:
+- compatible : Should be "mrvl,pxa-gpio" or "mrvl,mmp-gpio"
+- reg : Address and length of the register set for the device
+- interrupts : Should be the port interrupt shared by all gpio pins, if
+- interrupt-name : Should be the name of irq resource.
+ one number.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be one. It is the pin number.
+
+Example:
+
+ gpio: gpio@d4019000 {
+ compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio";
+ reg = <0xd4019000 0x1000>;
+ interrupts = <49>, <17>, <18>;
+ interrupt-name = "gpio_mux", "gpio0", "gpio1";
+ gpio-controller;
+ #gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
--- /dev/null
+* I2C
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "mrvl,mmp-twsi" where CHIP is the name of a
+ compatible processor, e.g. pxa168, pxa910, mmp2, mmp3.
+ For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required
+ as shown in the example below.
+
+Recommended properties :
+
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling
+ status register of i2c controller instead.
+ - mrvl,i2c-fast-mode : Enable fast mode of i2c controller.
+
+Examples:
+ twsi1: i2c@d4011000 {
+ compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c";
+ reg = <0xd4011000 0x1000>;
+ interrupts = <7>;
+ mrvl,i2c-fast-mode;
+ };
+
+ twsi2: i2c@d4025000 {
+ compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c";
+ reg = <0xd4025000 0x1000>;
+ interrupts = <58>;
+ };
+
--- /dev/null
+* Marvell Real Time Clock controller
+
+Required properties:
+- compatible: should be "mrvl,sa1100-rtc"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: Should be two. The first interrupt number is the rtc alarm
+ interrupt and the second interrupt number is the rtc hz interrupt.
+- interrupt-names: Assign name of irq resource.
+
+Example:
+ rtc: rtc@d4010000 {
+ compatible = "mrvl,mmp-rtc";
+ reg = <0xd4010000 0x1000>;
+ interrupts = <5>, <6>;
+ interrupt-name = "rtc 1Hz", "rtc alarm";
+ };
--- /dev/null
+PXA UART controller
+
+Required properties:
+- compatible : should be "mrvl,mmp-uart" or "mrvl,pxa-uart".
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
select CLKDEV_LOOKUP
+ select IRQ_DOMAIN
help
This enables support for systems based on the Atmel AT91RM9200,
AT91SAM9 processors.
--- /dev/null
+/*
+ * Copyright (C) 2011 Ilya Yanok, EmCraft Systems
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap3.dtsi"
+
+/ {
+ model = "TeeJet Mt.Ventoux";
+ compatible = "teejet,mt_ventoux", "ti,omap3";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ /* AM35xx doesn't have IVA */
+ soc {
+ iva {
+ status = "disabled";
+ };
+ };
+};
serial4 = &usart3;
serial5 = &usart4;
serial6 = &usart5;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ tcb0 = &tcb0;
+ tcb1 = &tcb1;
};
cpus {
cpu@0 {
ranges;
aic: interrupt-controller@fffff000 {
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
interrupt-parent;
reg = <0xfffff000 0x200>;
};
+ pit: timer@fffffd30 {
+ compatible = "atmel,at91sam9260-pit";
+ reg = <0xfffffd30 0xf>;
+ interrupts = <1 4>;
+ };
+
+ tcb0: timer@fffa0000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfffa0000 0x100>;
+ interrupts = <17 4 18 4 19 4>;
+ };
+
+ tcb1: timer@fffdc000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfffdc000 0x100>;
+ interrupts = <26 4 27 4 28 4>;
+ };
+
+ pioA: gpio@fffff400 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x100>;
+ interrupts = <2 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
+ pioB: gpio@fffff600 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x100>;
+ interrupts = <3 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
+ pioC: gpio@fffff800 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x100>;
+ interrupts = <4 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
- interrupts = <1>;
+ interrupts = <1 4>;
status = "disabled";
};
usart0: serial@fffb0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb0000 0x200>;
- interrupts = <6>;
+ interrupts = <6 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart1: serial@fffb4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb4000 0x200>;
- interrupts = <7>;
+ interrupts = <7 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart2: serial@fffb8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb8000 0x200>;
- interrupts = <8>;
+ interrupts = <8 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart3: serial@fffd0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd0000 0x200>;
- interrupts = <23>;
+ interrupts = <23 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart4: serial@fffd4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd4000 0x200>;
- interrupts = <24>;
+ interrupts = <24 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart5: serial@fffd8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd8000 0x200>;
- interrupts = <25>;
+ interrupts = <25 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
macb0: ethernet@fffc4000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xfffc4000 0x100>;
- interrupts = <21>;
+ interrupts = <21 4>;
status = "disabled";
};
};
serial2 = &usart1;
serial3 = &usart2;
serial4 = &usart3;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ gpio3 = &pioD;
+ gpio4 = &pioE;
+ tcb0 = &tcb0;
+ tcb1 = &tcb1;
};
cpus {
cpu@0 {
ranges;
aic: interrupt-controller@fffff000 {
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
interrupt-parent;
reg = <0xfffff000 0x200>;
};
+ pit: timer@fffffd30 {
+ compatible = "atmel,at91sam9260-pit";
+ reg = <0xfffffd30 0xf>;
+ interrupts = <1 4>;
+ };
+
+
+ tcb0: timer@fff7c000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfff7c000 0x100>;
+ interrupts = <18 4>;
+ };
+
+ tcb1: timer@fffd4000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfffd4000 0x100>;
+ interrupts = <18 4>;
+ };
+
dma: dma-controller@ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
- interrupts = <21>;
+ interrupts = <21 4>;
+ };
+
+ pioA: gpio@fffff200 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff200 0x100>;
+ interrupts = <2 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
+ pioB: gpio@fffff400 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x100>;
+ interrupts = <3 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
+ pioC: gpio@fffff600 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x100>;
+ interrupts = <4 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
+ pioD: gpio@fffff800 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x100>;
+ interrupts = <5 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
+ pioE: gpio@fffffa00 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x100>;
+ interrupts = <5 4>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
};
dbgu: serial@ffffee00 {
compatible = "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
- interrupts = <1>;
+ interrupts = <1 4>;
status = "disabled";
};
usart0: serial@fff8c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff8c000 0x200>;
- interrupts = <7>;
+ interrupts = <7 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart1: serial@fff90000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff90000 0x200>;
- interrupts = <8>;
+ interrupts = <8 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart2: serial@fff94000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff94000 0x200>;
- interrupts = <9>;
+ interrupts = <9 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart3: serial@fff98000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff98000 0x200>;
- interrupts = <10>;
+ interrupts = <10 4>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
macb0: ethernet@fffbc000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xfffbc000 0x100>;
- interrupts = <25>;
+ interrupts = <25 4>;
status = "disabled";
};
};
};
};
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ d8 {
+ label = "d8";
+ gpios = <&pioD 30 0>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ d6 {
+ label = "d6";
+ gpios = <&pioD 0 1>;
+ linux,default-trigger = "nand-disk";
+ };
+
+ d7 {
+ label = "d7";
+ gpios = <&pioD 31 1>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ left_click {
+ label = "left_click";
+ gpios = <&pioB 6 1>;
+ linux,code = <272>;
+ gpio-key,wakeup;
+ };
+
+ right_click {
+ label = "right_click";
+ gpios = <&pioB 7 1>;
+ linux,code = <273>;
+ gpio-key,wakeup;
+ };
+
+ left {
+ label = "Joystick Left";
+ gpios = <&pioB 14 1>;
+ linux,code = <105>;
+ };
+
+ right {
+ label = "Joystick Right";
+ gpios = <&pioB 15 1>;
+ linux,code = <106>;
+ };
+
+ up {
+ label = "Joystick Up";
+ gpios = <&pioB 16 1>;
+ linux,code = <103>;
+ };
+
+ down {
+ label = "Joystick Down";
+ gpios = <&pioB 17 1>;
+ linux,code = <108>;
+ };
+
+ enter {
+ label = "Joystick Press";
+ gpios = <&pioB 18 1>;
+ linux,code = <28>;
+ };
+ };
};
};
pioA: gpio@fffff400 {
- compatible = "atmel,at91rm9200-gpio";
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
interrupts = <2 4>;
#gpio-cells = <2>;
gpio-controller;
+ interrupt-controller;
};
pioB: gpio@fffff600 {
- compatible = "atmel,at91rm9200-gpio";
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
interrupts = <2 4>;
#gpio-cells = <2>;
gpio-controller;
+ interrupt-controller;
};
pioC: gpio@fffff800 {
- compatible = "atmel,at91rm9200-gpio";
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
interrupts = <3 4>;
#gpio-cells = <2>;
gpio-controller;
+ interrupt-controller;
};
pioD: gpio@fffffa00 {
- compatible = "atmel,at91rm9200-gpio";
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
interrupts = <3 4>;
#gpio-cells = <2>;
gpio-controller;
+ interrupt-controller;
};
dbgu: serial@fffff200 {
memory@20000000 {
reg = <0x20000000 0x8000000>;
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ pb18 {
+ label = "pb18";
+ gpios = <&pioB 18 1>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ pd21 {
+ label = "pd21";
+ gpios = <&pioD 21 0>;
+ };
+ };
};
--- /dev/null
+/*
+ * Copyright 2012 Sascha Hauer, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx27.dtsi"
+
+/ {
+ model = "Phytec pcm038";
+ compatible = "phytec,imx27-pcm038", "fsl,imx27";
+
+ memory {
+ reg = <0x0 0x0>;
+ };
+
+ soc {
+ aipi@10000000 { /* aipi */
+
+ wdog@10002000 {
+ status = "okay";
+ };
+
+ uart@1000a000 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+ };
+
+ uart@1000b000 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+ };
+
+ uart@1000c000 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+ };
+
+ fec@1002b000 {
+ status = "okay";
+ };
+
+ i2c@1001d000 {
+ clock-frequency = <400000>;
+ status = "okay";
+ at24@4c {
+ compatible = "at,24c32";
+ pagesize = <32>;
+ reg = <0x52>;
+ };
+ pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+ lm75@4a {
+ compatible = "national,lm75";
+ reg = <0x4a>;
+ };
+ };
+ };
+ };
+
+ nor_flash@c0000000 {
+ compatible = "cfi-flash";
+ bank-width = <2>;
+ reg = <0xc0000000 0x02000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
--- /dev/null
+/*
+ * Copyright 2012 Sascha Hauer, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ serial5 = &uart6;
+ };
+
+ avic: avic-interrupt-controller@e0000000 {
+ compatible = "fsl,imx27-avic", "fsl,avic";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x10040000 0x1000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ osc26m {
+ compatible = "fsl,imx-osc26m", "fixed-clock";
+ clock-frequency = <26000000>;
+ };
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&avic>;
+ ranges;
+
+ aipi@10000000 { /* AIPI1 */
+ compatible = "fsl,aipi-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x10000000 0x10000000>;
+ ranges;
+
+ wdog@10002000 {
+ compatible = "fsl,imx27-wdt", "fsl,imx21-wdt";
+ reg = <0x10002000 0x4000>;
+ interrupts = <27>;
+ status = "disabled";
+ };
+
+ uart1: uart@1000a000 {
+ compatible = "fsl,imx27-uart", "fsl,imx21-uart";
+ reg = <0x1000a000 0x1000>;
+ interrupts = <20>;
+ status = "disabled";
+ };
+
+ uart2: uart@1000b000 {
+ compatible = "fsl,imx27-uart", "fsl,imx21-uart";
+ reg = <0x1000b000 0x1000>;
+ interrupts = <19>;
+ status = "disabled";
+ };
+
+ uart3: uart@1000c000 {
+ compatible = "fsl,imx27-uart", "fsl,imx21-uart";
+ reg = <0x1000c000 0x1000>;
+ interrupts = <18>;
+ status = "disabled";
+ };
+
+ uart4: uart@1000d000 {
+ compatible = "fsl,imx27-uart", "fsl,imx21-uart";
+ reg = <0x1000d000 0x1000>;
+ interrupts = <17>;
+ status = "disabled";
+ };
+
+ cspi1: cspi@1000e000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx27-cspi";
+ reg = <0x1000e000 0x1000>;
+ interrupts = <16>;
+ status = "disabled";
+ };
+
+ cspi2: cspi@1000f000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx27-cspi";
+ reg = <0x1000f000 0x1000>;
+ interrupts = <15>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@10012000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx27-i2c", "fsl,imx1-i2c";
+ reg = <0x10012000 0x1000>;
+ interrupts = <12>;
+ status = "disabled";
+ };
+
+ gpio1: gpio@10015000 {
+ compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+ reg = <0x10015000 0x100>;
+ interrupts = <8>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio2: gpio@10015100 {
+ compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+ reg = <0x10015100 0x100>;
+ interrupts = <8>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio3: gpio@10015200 {
+ compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+ reg = <0x10015200 0x100>;
+ interrupts = <8>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio4: gpio@10015300 {
+ compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+ reg = <0x10015300 0x100>;
+ interrupts = <8>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio5: gpio@10015400 {
+ compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+ reg = <0x10015400 0x100>;
+ interrupts = <8>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio6: gpio@10015500 {
+ compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+ reg = <0x10015500 0x100>;
+ interrupts = <8>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ cspi3: cspi@10017000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx27-cspi";
+ reg = <0x10017000 0x1000>;
+ interrupts = <6>;
+ status = "disabled";
+ };
+
+ uart5: uart@1001b000 {
+ compatible = "fsl,imx27-uart", "fsl,imx21-uart";
+ reg = <0x1001b000 0x1000>;
+ interrupts = <49>;
+ status = "disabled";
+ };
+
+ uart6: uart@1001c000 {
+ compatible = "fsl,imx27-uart", "fsl,imx21-uart";
+ reg = <0x1001c000 0x1000>;
+ interrupts = <48>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@1001d000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx27-i2c", "fsl,imx1-i2c";
+ reg = <0x1001d000 0x1000>;
+ interrupts = <1>;
+ status = "disabled";
+ };
+
+ fec: fec@1002b000 {
+ compatible = "fsl,imx27-fec";
+ reg = <0x1002b000 0x4000>;
+ interrupts = <50>;
+ status = "disabled";
+ };
+ };
+ };
+};
compatible = "fsl,mc13892";
spi-max-frequency = <6000000>;
reg = <0>;
- mc13xxx-irq-gpios = <&gpio1 8 0>;
- fsl,mc13xxx-uses-regulator;
+ interrupt-parent = <&gpio1>;
+ interrupts = <8>;
+
+ regulators {
+ sw1_reg: sw1 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1375000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3_reg: sw3 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vpll_reg: vpll {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdig_reg: vdig {
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ };
+
+ vsd_reg: vsd {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3150000>;
+ };
+
+ vusb2_reg: vusb2 {
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <2775000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vvideo_reg: vvideo {
+ regulator-min-microvolt = <2775000>;
+ regulator-max-microvolt = <2775000>;
+ };
+
+ vaudio_reg: vaudio {
+ regulator-min-microvolt = <2300000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vcam_reg: vcam {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-always-on;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-always-on;
+ };
+ };
};
flash: at45db321d@1 {
usdhc@02198000 { /* uSDHC3 */
cd-gpios = <&gpio6 11 0>;
wp-gpios = <&gpio6 14 0>;
+ vmmc-supply = <®_3p3v>;
status = "okay";
};
usdhc@0219c000 { /* uSDHC4 */
fsl,card-wired;
+ vmmc-supply = <®_3p3v>;
status = "okay";
};
};
};
+ regulators {
+ compatible = "simple-bus";
+
+ reg_3p3v: 3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+
leds {
compatible = "gpio-leds";
usdhc@02198000 { /* uSDHC3 */
cd-gpios = <&gpio7 0 0>;
wp-gpios = <&gpio7 1 0>;
+ vmmc-supply = <®_3p3v>;
status = "okay";
};
usdhc@0219c000 { /* uSDHC4 */
cd-gpios = <&gpio2 6 0>;
wp-gpios = <&gpio2 7 0>;
+ vmmc-supply = <®_3p3v>;
status = "okay";
};
uart2: uart@021e8000 {
status = "okay";
};
+
+ i2c@021a0000 { /* I2C1 */
+ status = "okay";
+ clock-frequency = <100000>;
+
+ codec: sgtl5000@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+ };
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_2p5v: 2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: 3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};
};
};
model = "TI OMAP3 BeagleBoard";
compatible = "ti,omap3-beagle", "ti,omap3";
- /*
- * Since the initial device tree board file does not create any
- * devices (MMC, network...), the only way to boot is to provide a
- * ramdisk.
- */
- chosen {
- bootargs = "root=/dev/ram0 rw console=ttyO2,115200n8 initrd=0x81600000,20M ramdisk_size=20480 no_console_suspend debug earlyprintk";
- };
-
memory {
device_type = "memory";
reg = <0x80000000 0x20000000>; /* 512 MB */
--- /dev/null
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap3.dtsi"
+
+/ {
+ model = "TI OMAP3 EVM (OMAP3530, AM/DM37x)";
+ compatible = "ti,omap3-evm", "ti,omap3";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+};
ranges;
ti,hwmods = "l3_main";
- intc: interrupt-controller@1 {
- compatible = "ti,omap3-intc";
+ intc: interrupt-controller@48200000 {
+ compatible = "ti,omap2-intc";
interrupt-controller;
#interrupt-cells = <1>;
+ ti,intc-size = <96>;
+ reg = <0x48200000 0x1000>;
};
- uart1: serial@0x4806a000 {
+ uart1: serial@4806a000 {
compatible = "ti,omap3-uart";
ti,hwmods = "uart1";
clock-frequency = <48000000>;
};
- uart2: serial@0x4806c000 {
+ uart2: serial@4806c000 {
compatible = "ti,omap3-uart";
ti,hwmods = "uart2";
clock-frequency = <48000000>;
};
- uart3: serial@0x49020000 {
+ uart3: serial@49020000 {
compatible = "ti,omap3-uart";
ti,hwmods = "uart3";
clock-frequency = <48000000>;
};
- uart4: serial@0x49042000 {
+ uart4: serial@49042000 {
compatible = "ti,omap3-uart";
ti,hwmods = "uart4";
clock-frequency = <48000000>;
};
+
+ i2c1: i2c@48070000 {
+ compatible = "ti,omap3-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c1";
+ };
+
+ i2c2: i2c@48072000 {
+ compatible = "ti,omap3-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c2";
+ };
+
+ i2c3: i2c@48060000 {
+ compatible = "ti,omap3-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c3";
+ };
};
};
model = "TI OMAP4 PandaBoard";
compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
- /*
- * Since the initial device tree board file does not create any
- * devices (MMC, network...), the only way to boot is to provide a
- * ramdisk.
- */
- chosen {
- bootargs = "root=/dev/ram0 rw console=ttyO2,115200n8 initrd=0x81600000,20M ramdisk_size=20480 no_console_suspend debug";
- };
-
memory {
device_type = "memory";
reg = <0x80000000 0x40000000>; /* 1 GB */
model = "TI OMAP4 SDP board";
compatible = "ti,omap4-sdp", "ti,omap4430", "ti,omap4";
- /*
- * Since the initial device tree board file does not create any
- * devices (MMC, network...), the only way to boot is to provide a
- * ramdisk.
- */
- chosen {
- bootargs = "root=/dev/ram0 rw console=ttyO2,115200n8 initrd=0x81600000,20M ramdisk_size=20480 no_console_suspend debug";
- };
-
memory {
device_type = "memory";
reg = <0x80000000 0x40000000>; /* 1 GB */
gic: interrupt-controller@48241000 {
compatible = "arm,cortex-a9-gic";
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <3>;
reg = <0x48241000 0x1000>,
<0x48240100 0x0100>;
};
- uart1: serial@0x4806a000 {
+ uart1: serial@4806a000 {
compatible = "ti,omap4-uart";
ti,hwmods = "uart1";
clock-frequency = <48000000>;
};
- uart2: serial@0x4806c000 {
+ uart2: serial@4806c000 {
compatible = "ti,omap4-uart";
ti,hwmods = "uart2";
clock-frequency = <48000000>;
};
- uart3: serial@0x48020000 {
+ uart3: serial@48020000 {
compatible = "ti,omap4-uart";
ti,hwmods = "uart3";
clock-frequency = <48000000>;
};
- uart4: serial@0x4806e000 {
+ uart4: serial@4806e000 {
compatible = "ti,omap4-uart";
ti,hwmods = "uart4";
clock-frequency = <48000000>;
};
+
+ i2c1: i2c@48070000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c1";
+ };
+
+ i2c2: i2c@48072000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c2";
+ };
+
+ i2c3: i2c@48060000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c3";
+ };
+
+ i2c4: i2c@48350000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c4";
+ };
};
};
--- /dev/null
+/*
+ * Copyright (C) 2012 Marvell Technology Group Ltd.
+ * Author: Haojian Zhuang <haojian.zhuang@marvell.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ */
+
+/dts-v1/;
+/include/ "pxa168.dtsi"
+
+/ {
+ model = "Marvell PXA168 Aspenite Development Board";
+ compatible = "mrvl,pxa168-aspenite", "mrvl,pxa168";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 root=/dev/nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on";
+ };
+
+ memory {
+ reg = <0x00000000 0x04000000>;
+ };
+
+ soc {
+ apb@d4000000 {
+ uart1: uart@d4017000 {
+ status = "okay";
+ };
+ twsi1: i2c@d4011000 {
+ status = "okay";
+ };
+ rtc: rtc@d4010000 {
+ status = "okay";
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2012 Marvell Technology Group Ltd.
+ * Author: Haojian Zhuang <haojian.zhuang@marvell.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ i2c0 = &twsi1;
+ i2c1 = &twsi2;
+ };
+
+ intc: intc-interrupt-controller@d4282000 {
+ compatible = "mrvl,mmp-intc", "mrvl,intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0xd4282000 0x1000>;
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&intc>;
+ ranges;
+
+ apb@d4000000 { /* APB */
+ compatible = "mrvl,apb-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd4000000 0x00200000>;
+ ranges;
+
+ uart1: uart@d4017000 {
+ compatible = "mrvl,mmp-uart", "mrvl,pxa-uart";
+ reg = <0xd4017000 0x1000>;
+ interrupts = <27>;
+ status = "disabled";
+ };
+
+ uart2: uart@d4018000 {
+ compatible = "mrvl,mmp-uart", "mrvl,pxa-uart";
+ reg = <0xd4018000 0x1000>;
+ interrupts = <28>;
+ status = "disabled";
+ };
+
+ uart3: uart@d4026000 {
+ compatible = "mrvl,mmp-uart", "mrvl,pxa-uart";
+ reg = <0xd4026000 0x1000>;
+ interrupts = <29>;
+ status = "disabled";
+ };
+
+ gpio: gpio@d4019000 {
+ compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio";
+ reg = <0xd4019000 0x1000>;
+ interrupts = <49>;
+ interrupt-names = "gpio_mux";
+ gpio-controller;
+ #gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ twsi1: i2c@d4011000 {
+ compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c";
+ reg = <0xd4011000 0x1000>;
+ interrupts = <7>;
+ mrvl,i2c-fast-mode;
+ status = "disabled";
+ };
+
+ twsi2: i2c@d4025000 {
+ compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c";
+ reg = <0xd4025000 0x1000>;
+ interrupts = <58>;
+ status = "disabled";
+ };
+
+ rtc: rtc@d4010000 {
+ compatible = "mrvl,mmp-rtc";
+ reg = <0xd4010000 0x1000>;
+ interrupts = <5 6>;
+ interrupt-names = "rtc 1Hz", "rtc alarm";
+ status = "disabled";
+ };
+ };
+ };
+};
i2c@7000d000 {
clock-frequency = <100000>;
};
+
+ sdhci@78000000 {
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 155 0>; /* gpio PT3 */
+ power-gpios = <&gpio 31 0>; /* gpio PD7 */
+ };
+
+ sdhci@78000200 {
+ status = "disable";
+ };
+
+ sdhci@78000400 {
+ status = "disable";
+ };
+
+ sdhci@78000400 {
+ support-8bit;
+ };
};
"Headset Mic", "MICBIAS1",
"MIC1", "Headset Mic",
"Headset Stereophone", "HPR",
- "Headset Stereophone", "HPL";
+ "Headset Stereophone", "HPL",
+ "DMICDAT", "Digital Mic";
nvidia,audio-codec = <&alc5632>;
nvidia,i2s-controller = <&tegra_i2s1>;
< 0x50040100 0x0100 >;
};
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 56 0x04
+ 0 57 0x04>;
+ };
+
apbdma: dma@6000a000 {
compatible = "nvidia,tegra20-apbdma";
reg = <0x6000a000 0x1200>;
< 0x50040100 0x0100 >;
};
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 144 0x04
+ 0 145 0x04
+ 0 146 0x04
+ 0 147 0x04>;
+ };
+
apbdma: dma@6000a000 {
compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
reg = <0x6000a000 0x1400>;
};
};
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ user_led {
+ label = "user_led";
+ gpios = <&pioB 21 1>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ user_pb {
+ label = "user_pb";
+ gpios = <&pioB 10 1>;
+ linux,code = <28>;
+ gpio-key,wakeup;
+ };
+ };
};
--- /dev/null
+/*
+ * ARM Ltd. Versatile Express
+ *
+ * Motherboard Express uATX
+ * V2M-P1
+ *
+ * HBI-0190D
+ *
+ * RS1 memory map ("ARM Cortex-A Series memory map" in the board's
+ * Technical Reference Manual)
+ *
+ * WARNING! The hardware described in this file is independent from the
+ * original variant (vexpress-v2m.dtsi), but there is a strong
+ * correspondence between the two configurations.
+ *
+ * TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT
+ * CHANGES TO vexpress-v2m.dtsi!
+ */
+
+/ {
+ aliases {
+ arm,v2m_timer = &v2m_timer01;
+ };
+
+ motherboard {
+ compatible = "simple-bus";
+ arm,v2m-memory-map = "rs1";
+ #address-cells = <2>; /* SMB chipselect number and offset */
+ #size-cells = <1>;
+ #interrupt-cells = <1>;
+
+ flash@0,00000000 {
+ compatible = "arm,vexpress-flash", "cfi-flash";
+ reg = <0 0x00000000 0x04000000>,
+ <4 0x00000000 0x04000000>;
+ bank-width = <4>;
+ };
+
+ psram@1,00000000 {
+ compatible = "arm,vexpress-psram", "mtd-ram";
+ reg = <1 0x00000000 0x02000000>;
+ bank-width = <4>;
+ };
+
+ vram@2,00000000 {
+ compatible = "arm,vexpress-vram";
+ reg = <2 0x00000000 0x00800000>;
+ };
+
+ ethernet@2,02000000 {
+ compatible = "smsc,lan9118", "smsc,lan9115";
+ reg = <2 0x02000000 0x10000>;
+ interrupts = <15>;
+ phy-mode = "mii";
+ reg-io-width = <4>;
+ smsc,irq-active-high;
+ smsc,irq-push-pull;
+ };
+
+ usb@2,03000000 {
+ compatible = "nxp,usb-isp1761";
+ reg = <2 0x03000000 0x20000>;
+ interrupts = <16>;
+ port1-otg;
+ };
+
+ iofpga@3,00000000 {
+ compatible = "arm,amba-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 3 0 0x200000>;
+
+ sysreg@010000 {
+ compatible = "arm,vexpress-sysreg";
+ reg = <0x010000 0x1000>;
+ };
+
+ sysctl@020000 {
+ compatible = "arm,sp810", "arm,primecell";
+ reg = <0x020000 0x1000>;
+ };
+
+ /* PCI-E I2C bus */
+ v2m_i2c_pcie: i2c@030000 {
+ compatible = "arm,versatile-i2c";
+ reg = <0x030000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pcie-switch@60 {
+ compatible = "idt,89hpes32h8";
+ reg = <0x60>;
+ };
+ };
+
+ aaci@040000 {
+ compatible = "arm,pl041", "arm,primecell";
+ reg = <0x040000 0x1000>;
+ interrupts = <11>;
+ };
+
+ mmci@050000 {
+ compatible = "arm,pl180", "arm,primecell";
+ reg = <0x050000 0x1000>;
+ interrupts = <9 10>;
+ };
+
+ kmi@060000 {
+ compatible = "arm,pl050", "arm,primecell";
+ reg = <0x060000 0x1000>;
+ interrupts = <12>;
+ };
+
+ kmi@070000 {
+ compatible = "arm,pl050", "arm,primecell";
+ reg = <0x070000 0x1000>;
+ interrupts = <13>;
+ };
+
+ v2m_serial0: uart@090000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x090000 0x1000>;
+ interrupts = <5>;
+ };
+
+ v2m_serial1: uart@0a0000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0a0000 0x1000>;
+ interrupts = <6>;
+ };
+
+ v2m_serial2: uart@0b0000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0b0000 0x1000>;
+ interrupts = <7>;
+ };
+
+ v2m_serial3: uart@0c0000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0c0000 0x1000>;
+ interrupts = <8>;
+ };
+
+ wdt@0f0000 {
+ compatible = "arm,sp805", "arm,primecell";
+ reg = <0x0f0000 0x1000>;
+ interrupts = <0>;
+ };
+
+ v2m_timer01: timer@110000 {
+ compatible = "arm,sp804", "arm,primecell";
+ reg = <0x110000 0x1000>;
+ interrupts = <2>;
+ };
+
+ v2m_timer23: timer@120000 {
+ compatible = "arm,sp804", "arm,primecell";
+ reg = <0x120000 0x1000>;
+ };
+
+ /* DVI I2C bus */
+ v2m_i2c_dvi: i2c@160000 {
+ compatible = "arm,versatile-i2c";
+ reg = <0x160000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dvi-transmitter@39 {
+ compatible = "sil,sii9022-tpi", "sil,sii9022";
+ reg = <0x39>;
+ };
+
+ dvi-transmitter@60 {
+ compatible = "sil,sii9022-cpi", "sil,sii9022";
+ reg = <0x60>;
+ };
+ };
+
+ rtc@170000 {
+ compatible = "arm,pl031", "arm,primecell";
+ reg = <0x170000 0x1000>;
+ interrupts = <4>;
+ };
+
+ compact-flash@1a0000 {
+ compatible = "arm,vexpress-cf", "ata-generic";
+ reg = <0x1a0000 0x100
+ 0x1a0100 0xf00>;
+ reg-shift = <2>;
+ };
+
+ clcd@1f0000 {
+ compatible = "arm,pl111", "arm,primecell";
+ reg = <0x1f0000 0x1000>;
+ interrupts = <14>;
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * ARM Ltd. Versatile Express
+ *
+ * Motherboard Express uATX
+ * V2M-P1
+ *
+ * HBI-0190D
+ *
+ * Original memory map ("Legacy memory map" in the board's
+ * Technical Reference Manual)
+ *
+ * WARNING! The hardware described in this file is independent from the
+ * RS1 variant (vexpress-v2m-rs1.dtsi), but there is a strong
+ * correspondence between the two configurations.
+ *
+ * TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT
+ * CHANGES TO vexpress-v2m-rs1.dtsi!
+ */
+
+/ {
+ aliases {
+ arm,v2m_timer = &v2m_timer01;
+ };
+
+ motherboard {
+ compatible = "simple-bus";
+ #address-cells = <2>; /* SMB chipselect number and offset */
+ #size-cells = <1>;
+ #interrupt-cells = <1>;
+
+ flash@0,00000000 {
+ compatible = "arm,vexpress-flash", "cfi-flash";
+ reg = <0 0x00000000 0x04000000>,
+ <1 0x00000000 0x04000000>;
+ bank-width = <4>;
+ };
+
+ psram@2,00000000 {
+ compatible = "arm,vexpress-psram", "mtd-ram";
+ reg = <2 0x00000000 0x02000000>;
+ bank-width = <4>;
+ };
+
+ vram@3,00000000 {
+ compatible = "arm,vexpress-vram";
+ reg = <3 0x00000000 0x00800000>;
+ };
+
+ ethernet@3,02000000 {
+ compatible = "smsc,lan9118", "smsc,lan9115";
+ reg = <3 0x02000000 0x10000>;
+ interrupts = <15>;
+ phy-mode = "mii";
+ reg-io-width = <4>;
+ smsc,irq-active-high;
+ smsc,irq-push-pull;
+ };
+
+ usb@3,03000000 {
+ compatible = "nxp,usb-isp1761";
+ reg = <3 0x03000000 0x20000>;
+ interrupts = <16>;
+ port1-otg;
+ };
+
+ iofpga@7,00000000 {
+ compatible = "arm,amba-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 7 0 0x20000>;
+
+ sysreg@00000 {
+ compatible = "arm,vexpress-sysreg";
+ reg = <0x00000 0x1000>;
+ };
+
+ sysctl@01000 {
+ compatible = "arm,sp810", "arm,primecell";
+ reg = <0x01000 0x1000>;
+ };
+
+ /* PCI-E I2C bus */
+ v2m_i2c_pcie: i2c@02000 {
+ compatible = "arm,versatile-i2c";
+ reg = <0x02000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pcie-switch@60 {
+ compatible = "idt,89hpes32h8";
+ reg = <0x60>;
+ };
+ };
+
+ aaci@04000 {
+ compatible = "arm,pl041", "arm,primecell";
+ reg = <0x04000 0x1000>;
+ interrupts = <11>;
+ };
+
+ mmci@05000 {
+ compatible = "arm,pl180", "arm,primecell";
+ reg = <0x05000 0x1000>;
+ interrupts = <9 10>;
+ };
+
+ kmi@06000 {
+ compatible = "arm,pl050", "arm,primecell";
+ reg = <0x06000 0x1000>;
+ interrupts = <12>;
+ };
+
+ kmi@07000 {
+ compatible = "arm,pl050", "arm,primecell";
+ reg = <0x07000 0x1000>;
+ interrupts = <13>;
+ };
+
+ v2m_serial0: uart@09000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x09000 0x1000>;
+ interrupts = <5>;
+ };
+
+ v2m_serial1: uart@0a000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0a000 0x1000>;
+ interrupts = <6>;
+ };
+
+ v2m_serial2: uart@0b000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0b000 0x1000>;
+ interrupts = <7>;
+ };
+
+ v2m_serial3: uart@0c000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0c000 0x1000>;
+ interrupts = <8>;
+ };
+
+ wdt@0f000 {
+ compatible = "arm,sp805", "arm,primecell";
+ reg = <0x0f000 0x1000>;
+ interrupts = <0>;
+ };
+
+ v2m_timer01: timer@11000 {
+ compatible = "arm,sp804", "arm,primecell";
+ reg = <0x11000 0x1000>;
+ interrupts = <2>;
+ };
+
+ v2m_timer23: timer@12000 {
+ compatible = "arm,sp804", "arm,primecell";
+ reg = <0x12000 0x1000>;
+ };
+
+ /* DVI I2C bus */
+ v2m_i2c_dvi: i2c@16000 {
+ compatible = "arm,versatile-i2c";
+ reg = <0x16000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dvi-transmitter@39 {
+ compatible = "sil,sii9022-tpi", "sil,sii9022";
+ reg = <0x39>;
+ };
+
+ dvi-transmitter@60 {
+ compatible = "sil,sii9022-cpi", "sil,sii9022";
+ reg = <0x60>;
+ };
+ };
+
+ rtc@17000 {
+ compatible = "arm,pl031", "arm,primecell";
+ reg = <0x17000 0x1000>;
+ interrupts = <4>;
+ };
+
+ compact-flash@1a000 {
+ compatible = "arm,vexpress-cf", "ata-generic";
+ reg = <0x1a000 0x100
+ 0x1a100 0xf00>;
+ reg-shift = <2>;
+ };
+
+ clcd@1f000 {
+ compatible = "arm,pl111", "arm,primecell";
+ reg = <0x1f000 0x1000>;
+ interrupts = <14>;
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * ARM Ltd. Versatile Express
+ *
+ * CoreTile Express A15x2 (version with Test Chip 1)
+ * Cortex-A15 MPCore (V2P-CA15)
+ *
+ * HBI-0237A
+ */
+
+/dts-v1/;
+
+/ {
+ model = "V2P-CA15";
+ arm,hbi = <0x237>;
+ compatible = "arm,vexpress,v2p-ca15,tc1", "arm,vexpress,v2p-ca15", "arm,vexpress";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ chosen { };
+
+ aliases {
+ serial0 = &v2m_serial0;
+ serial1 = &v2m_serial1;
+ serial2 = &v2m_serial2;
+ serial3 = &v2m_serial3;
+ i2c0 = &v2m_i2c_dvi;
+ i2c1 = &v2m_i2c_pcie;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <1>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+
+ hdlcd@2b000000 {
+ compatible = "arm,hdlcd";
+ reg = <0x2b000000 0x1000>;
+ interrupts = <0 85 4>;
+ };
+
+ memory-controller@2b0a0000 {
+ compatible = "arm,pl341", "arm,primecell";
+ reg = <0x2b0a0000 0x1000>;
+ };
+
+ wdt@2b060000 {
+ compatible = "arm,sp805", "arm,primecell";
+ reg = <0x2b060000 0x1000>;
+ interrupts = <98>;
+ };
+
+ gic: interrupt-controller@2c001000 {
+ compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x2c001000 0x1000>,
+ <0x2c002000 0x100>;
+ };
+
+ memory-controller@7ffd0000 {
+ compatible = "arm,pl354", "arm,primecell";
+ reg = <0x7ffd0000 0x1000>;
+ interrupts = <0 86 4>,
+ <0 87 4>;
+ };
+
+ dma@7ffb0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x7ffb0000 0x1000>;
+ interrupts = <0 92 4>,
+ <0 88 4>,
+ <0 89 4>,
+ <0 90 4>,
+ <0 91 4>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a15-pmu", "arm,cortex-a9-pmu";
+ interrupts = <0 68 4>,
+ <0 69 4>;
+ };
+
+ motherboard {
+ ranges = <0 0 0x08000000 0x04000000>,
+ <1 0 0x14000000 0x04000000>,
+ <2 0 0x18000000 0x04000000>,
+ <3 0 0x1c000000 0x04000000>,
+ <4 0 0x0c000000 0x04000000>,
+ <5 0 0x10000000 0x04000000>;
+
+ interrupt-map-mask = <0 0 63>;
+ interrupt-map = <0 0 0 &gic 0 0 4>,
+ <0 0 1 &gic 0 1 4>,
+ <0 0 2 &gic 0 2 4>,
+ <0 0 3 &gic 0 3 4>,
+ <0 0 4 &gic 0 4 4>,
+ <0 0 5 &gic 0 5 4>,
+ <0 0 6 &gic 0 6 4>,
+ <0 0 7 &gic 0 7 4>,
+ <0 0 8 &gic 0 8 4>,
+ <0 0 9 &gic 0 9 4>,
+ <0 0 10 &gic 0 10 4>,
+ <0 0 11 &gic 0 11 4>,
+ <0 0 12 &gic 0 12 4>,
+ <0 0 13 &gic 0 13 4>,
+ <0 0 14 &gic 0 14 4>,
+ <0 0 15 &gic 0 15 4>,
+ <0 0 16 &gic 0 16 4>,
+ <0 0 17 &gic 0 17 4>,
+ <0 0 18 &gic 0 18 4>,
+ <0 0 19 &gic 0 19 4>,
+ <0 0 20 &gic 0 20 4>,
+ <0 0 21 &gic 0 21 4>,
+ <0 0 22 &gic 0 22 4>,
+ <0 0 23 &gic 0 23 4>,
+ <0 0 24 &gic 0 24 4>,
+ <0 0 25 &gic 0 25 4>,
+ <0 0 26 &gic 0 26 4>,
+ <0 0 27 &gic 0 27 4>,
+ <0 0 28 &gic 0 28 4>,
+ <0 0 29 &gic 0 29 4>,
+ <0 0 30 &gic 0 30 4>,
+ <0 0 31 &gic 0 31 4>,
+ <0 0 32 &gic 0 32 4>,
+ <0 0 33 &gic 0 33 4>,
+ <0 0 34 &gic 0 34 4>,
+ <0 0 35 &gic 0 35 4>,
+ <0 0 36 &gic 0 36 4>,
+ <0 0 37 &gic 0 37 4>,
+ <0 0 38 &gic 0 38 4>,
+ <0 0 39 &gic 0 39 4>,
+ <0 0 40 &gic 0 40 4>,
+ <0 0 41 &gic 0 41 4>,
+ <0 0 42 &gic 0 42 4>;
+ };
+};
+
+/include/ "vexpress-v2m-rs1.dtsi"
--- /dev/null
+/*
+ * ARM Ltd. Versatile Express
+ *
+ * CoreTile Express A5x2
+ * Cortex-A5 MPCore (V2P-CA5s)
+ *
+ * HBI-0225B
+ */
+
+/dts-v1/;
+
+/ {
+ model = "V2P-CA5s";
+ arm,hbi = <0x225>;
+ compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ chosen { };
+
+ aliases {
+ serial0 = &v2m_serial0;
+ serial1 = &v2m_serial1;
+ serial2 = &v2m_serial2;
+ serial3 = &v2m_serial3;
+ i2c0 = &v2m_i2c_dvi;
+ i2c1 = &v2m_i2c_pcie;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a5";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a5";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+
+ hdlcd@2a110000 {
+ compatible = "arm,hdlcd";
+ reg = <0x2a110000 0x1000>;
+ interrupts = <0 85 4>;
+ };
+
+ memory-controller@2a150000 {
+ compatible = "arm,pl341", "arm,primecell";
+ reg = <0x2a150000 0x1000>;
+ };
+
+ memory-controller@2a190000 {
+ compatible = "arm,pl354", "arm,primecell";
+ reg = <0x2a190000 0x1000>;
+ interrupts = <0 86 4>,
+ <0 87 4>;
+ };
+
+ scu@2c000000 {
+ compatible = "arm,cortex-a5-scu";
+ reg = <0x2c000000 0x58>;
+ };
+
+ timer@2c000600 {
+ compatible = "arm,cortex-a5-twd-timer";
+ reg = <0x2c000600 0x38>;
+ interrupts = <1 2 0x304>,
+ <1 3 0x304>;
+ };
+
+ gic: interrupt-controller@2c001000 {
+ compatible = "arm,corex-a5-gic", "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x2c001000 0x1000>,
+ <0x2c000100 0x100>;
+ };
+
+ L2: cache-controller@2c0f0000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x2c0f0000 0x1000>;
+ interrupts = <0 84 4>;
+ cache-level = <2>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a5-pmu", "arm,cortex-a9-pmu";
+ interrupts = <0 68 4>,
+ <0 69 4>;
+ };
+
+ motherboard {
+ ranges = <0 0 0x08000000 0x04000000>,
+ <1 0 0x14000000 0x04000000>,
+ <2 0 0x18000000 0x04000000>,
+ <3 0 0x1c000000 0x04000000>,
+ <4 0 0x0c000000 0x04000000>,
+ <5 0 0x10000000 0x04000000>;
+
+ interrupt-map-mask = <0 0 63>;
+ interrupt-map = <0 0 0 &gic 0 0 4>,
+ <0 0 1 &gic 0 1 4>,
+ <0 0 2 &gic 0 2 4>,
+ <0 0 3 &gic 0 3 4>,
+ <0 0 4 &gic 0 4 4>,
+ <0 0 5 &gic 0 5 4>,
+ <0 0 6 &gic 0 6 4>,
+ <0 0 7 &gic 0 7 4>,
+ <0 0 8 &gic 0 8 4>,
+ <0 0 9 &gic 0 9 4>,
+ <0 0 10 &gic 0 10 4>,
+ <0 0 11 &gic 0 11 4>,
+ <0 0 12 &gic 0 12 4>,
+ <0 0 13 &gic 0 13 4>,
+ <0 0 14 &gic 0 14 4>,
+ <0 0 15 &gic 0 15 4>,
+ <0 0 16 &gic 0 16 4>,
+ <0 0 17 &gic 0 17 4>,
+ <0 0 18 &gic 0 18 4>,
+ <0 0 19 &gic 0 19 4>,
+ <0 0 20 &gic 0 20 4>,
+ <0 0 21 &gic 0 21 4>,
+ <0 0 22 &gic 0 22 4>,
+ <0 0 23 &gic 0 23 4>,
+ <0 0 24 &gic 0 24 4>,
+ <0 0 25 &gic 0 25 4>,
+ <0 0 26 &gic 0 26 4>,
+ <0 0 27 &gic 0 27 4>,
+ <0 0 28 &gic 0 28 4>,
+ <0 0 29 &gic 0 29 4>,
+ <0 0 30 &gic 0 30 4>,
+ <0 0 31 &gic 0 31 4>,
+ <0 0 32 &gic 0 32 4>,
+ <0 0 33 &gic 0 33 4>,
+ <0 0 34 &gic 0 34 4>,
+ <0 0 35 &gic 0 35 4>,
+ <0 0 36 &gic 0 36 4>,
+ <0 0 37 &gic 0 37 4>,
+ <0 0 38 &gic 0 38 4>,
+ <0 0 39 &gic 0 39 4>,
+ <0 0 40 &gic 0 40 4>,
+ <0 0 41 &gic 0 41 4>,
+ <0 0 42 &gic 0 42 4>;
+ };
+};
+
+/include/ "vexpress-v2m-rs1.dtsi"
--- /dev/null
+/*
+ * ARM Ltd. Versatile Express
+ *
+ * CoreTile Express A9x4
+ * Cortex-A9 MPCore (V2P-CA9)
+ *
+ * HBI-0191B
+ */
+
+/dts-v1/;
+
+/ {
+ model = "V2P-CA9";
+ arm,hbi = <0x191>;
+ compatible = "arm,vexpress,v2p-ca9", "arm,vexpress";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ chosen { };
+
+ aliases {
+ serial0 = &v2m_serial0;
+ serial1 = &v2m_serial1;
+ serial2 = &v2m_serial2;
+ serial3 = &v2m_serial3;
+ i2c0 = &v2m_i2c_dvi;
+ i2c1 = &v2m_i2c_pcie;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <2>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <3>;
+ next-level-cache = <&L2>;
+ };
+ };
+
+ memory@60000000 {
+ device_type = "memory";
+ reg = <0x60000000 0x40000000>;
+ };
+
+ clcd@10020000 {
+ compatible = "arm,pl111", "arm,primecell";
+ reg = <0x10020000 0x1000>;
+ interrupts = <0 44 4>;
+ };
+
+ memory-controller@100e0000 {
+ compatible = "arm,pl341", "arm,primecell";
+ reg = <0x100e0000 0x1000>;
+ };
+
+ memory-controller@100e1000 {
+ compatible = "arm,pl354", "arm,primecell";
+ reg = <0x100e1000 0x1000>;
+ interrupts = <0 45 4>,
+ <0 46 4>;
+ };
+
+ timer@100e4000 {
+ compatible = "arm,sp804", "arm,primecell";
+ reg = <0x100e4000 0x1000>;
+ interrupts = <0 48 4>,
+ <0 49 4>;
+ };
+
+ watchdog@100e5000 {
+ compatible = "arm,sp805", "arm,primecell";
+ reg = <0x100e5000 0x1000>;
+ interrupts = <0 51 4>;
+ };
+
+ scu@1e000000 {
+ compatible = "arm,cortex-a9-scu";
+ reg = <0x1e000000 0x58>;
+ };
+
+ timer@1e000600 {
+ compatible = "arm,cortex-a9-twd-timer";
+ reg = <0x1e000600 0x20>;
+ interrupts = <1 2 0xf04>,
+ <1 3 0xf04>;
+ };
+
+ gic: interrupt-controller@1e001000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x1e001000 0x1000>,
+ <0x1e000100 0x100>;
+ };
+
+ L2: cache-controller@1e00a000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x1e00a000 0x1000>;
+ interrupts = <0 43 4>;
+ cache-level = <2>;
+ arm,data-latency = <1 1 1>;
+ arm,tag-latency = <1 1 1>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 60 4>,
+ <0 61 4>,
+ <0 62 4>,
+ <0 63 4>;
+ };
+
+ motherboard {
+ ranges = <0 0 0x40000000 0x04000000>,
+ <1 0 0x44000000 0x04000000>,
+ <2 0 0x48000000 0x04000000>,
+ <3 0 0x4c000000 0x04000000>,
+ <7 0 0x10000000 0x00020000>;
+
+ interrupt-map-mask = <0 0 63>;
+ interrupt-map = <0 0 0 &gic 0 0 4>,
+ <0 0 1 &gic 0 1 4>,
+ <0 0 2 &gic 0 2 4>,
+ <0 0 3 &gic 0 3 4>,
+ <0 0 4 &gic 0 4 4>,
+ <0 0 5 &gic 0 5 4>,
+ <0 0 6 &gic 0 6 4>,
+ <0 0 7 &gic 0 7 4>,
+ <0 0 8 &gic 0 8 4>,
+ <0 0 9 &gic 0 9 4>,
+ <0 0 10 &gic 0 10 4>,
+ <0 0 11 &gic 0 11 4>,
+ <0 0 12 &gic 0 12 4>,
+ <0 0 13 &gic 0 13 4>,
+ <0 0 14 &gic 0 14 4>,
+ <0 0 15 &gic 0 15 4>,
+ <0 0 16 &gic 0 16 4>,
+ <0 0 17 &gic 0 17 4>,
+ <0 0 18 &gic 0 18 4>,
+ <0 0 19 &gic 0 19 4>,
+ <0 0 20 &gic 0 20 4>,
+ <0 0 21 &gic 0 21 4>,
+ <0 0 22 &gic 0 22 4>,
+ <0 0 23 &gic 0 23 4>,
+ <0 0 24 &gic 0 24 4>,
+ <0 0 25 &gic 0 25 4>,
+ <0 0 26 &gic 0 26 4>,
+ <0 0 27 &gic 0 27 4>,
+ <0 0 28 &gic 0 28 4>,
+ <0 0 29 &gic 0 29 4>,
+ <0 0 30 &gic 0 30 4>,
+ <0 0 31 &gic 0 31 4>,
+ <0 0 32 &gic 0 32 4>,
+ <0 0 33 &gic 0 33 4>,
+ <0 0 34 &gic 0 34 4>,
+ <0 0 35 &gic 0 35 4>,
+ <0 0 36 &gic 0 36 4>,
+ <0 0 37 &gic 0 37 4>,
+ <0 0 38 &gic 0 38 4>,
+ <0 0 39 &gic 0 39 4>,
+ <0 0 40 &gic 0 40 4>,
+ <0 0 41 &gic 0 41 4>,
+ <0 0 42 &gic 0 42 4>;
+ };
+};
+
+/include/ "vexpress-v2m.dtsi"
obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91SAM9G45) += at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT91SAM9X5) += at91sam9x5.o at91sam926x_time.o
+obj-$(CONFIG_ARCH_AT91SAM9X5) += at91sam9x5.o at91sam926x_time.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o
# AT91RM9200 board-specific support
initrd_phys-y := 0x20410000
endif
-dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9m10g45ek.dtb usb_a9g20.dtb
+# Keep dtb files sorted alphabetically for each SoC
+# sam9g20
+dtb-$(CONFIG_MACH_AT91SAM_DT) += usb_a9g20.dtb
+# sam9g45
+dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9m10g45ek.dtb
+# sam9x5
+dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9g25ek.dtb
* Disable the processor clock. The processor will be automatically
* re-enabled by an interrupt or by a reset.
*/
- at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+ at91_pmc_write(AT91_PMC_SCDR, AT91_PMC_PCK);
}
static void at91rm9200_restart(char mode, const char *cmd)
/*
* Perform a hardware reset with the use of the Watchdog timer.
*/
- at91_sys_write(AT91_ST_WDMR, AT91_ST_RSTEN | AT91_ST_EXTEN | 1);
- at91_sys_write(AT91_ST_CR, AT91_ST_WDRST);
+ at91_st_write(AT91_ST_WDMR, AT91_ST_RSTEN | AT91_ST_EXTEN | 1);
+ at91_st_write(AT91_ST_CR, AT91_ST_WDRST);
}
/* --------------------------------------------------------------------
static void __init at91rm9200_ioremap_registers(void)
{
+ at91rm9200_ioremap_st(AT91RM9200_BASE_ST);
+ at91_ioremap_ramc(0, AT91RM9200_BASE_MC, 256);
}
static void __init at91rm9200_initialize(void)
#include <mach/board.h>
#include <mach/at91rm9200.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
data->chipselect = 4; /* can only use EBI ChipSelect 4 */
/* CF takes over CS4, CS5, CS6 */
- csa = at91_sys_read(AT91_EBI_CSA);
- at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
+ csa = at91_ramc_read(0, AT91_EBI_CSA);
+ at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
/*
* Static memory controller timing adjustments.
* REVISIT: these timings are in terms of MCK cycles, so
* when MCK changes (cpufreq etc) so must these values...
*/
- at91_sys_write(AT91_SMC_CSR(4),
+ at91_ramc_write(0, AT91_SMC_CSR(4),
AT91_SMC_ACSS_STD
| AT91_SMC_DBW_16
| AT91_SMC_BAT
return;
/* enable the address range of CS3 */
- csa = at91_sys_read(AT91_EBI_CSA);
- at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
+ csa = at91_ramc_read(0, AT91_EBI_CSA);
+ at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
/* set the bus interface characteristics */
- at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
+ at91_ramc_write(0, AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
| AT91_SMC_NWS_(5)
| AT91_SMC_TDF_(1)
| AT91_SMC_RWSETUP_(0) /* tDS Data Set up Time 30 - ns */
}
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-struct platform_device *atmel_default_console_device; /* the serial console device */
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
{
unsigned long x1, x2;
- x1 = at91_sys_read(AT91_ST_CRTR);
+ x1 = at91_st_read(AT91_ST_CRTR);
do {
- x2 = at91_sys_read(AT91_ST_CRTR);
+ x2 = at91_st_read(AT91_ST_CRTR);
if (x1 == x2)
break;
x1 = x2;
*/
static irqreturn_t at91rm9200_timer_interrupt(int irq, void *dev_id)
{
- u32 sr = at91_sys_read(AT91_ST_SR) & irqmask;
+ u32 sr = at91_st_read(AT91_ST_SR) & irqmask;
/*
* irqs should be disabled here, but as the irq is shared they are only
clkevt32k_mode(enum clock_event_mode mode, struct clock_event_device *dev)
{
/* Disable and flush pending timer interrupts */
- at91_sys_write(AT91_ST_IDR, AT91_ST_PITS | AT91_ST_ALMS);
- (void) at91_sys_read(AT91_ST_SR);
+ at91_st_write(AT91_ST_IDR, AT91_ST_PITS | AT91_ST_ALMS);
+ at91_st_read(AT91_ST_SR);
last_crtr = read_CRTR();
switch (mode) {
case CLOCK_EVT_MODE_PERIODIC:
/* PIT for periodic irqs; fixed rate of 1/HZ */
irqmask = AT91_ST_PITS;
- at91_sys_write(AT91_ST_PIMR, RM9200_TIMER_LATCH);
+ at91_st_write(AT91_ST_PIMR, RM9200_TIMER_LATCH);
break;
case CLOCK_EVT_MODE_ONESHOT:
/* ALM for oneshot irqs, set by next_event()
* before 32 seconds have passed
*/
irqmask = AT91_ST_ALMS;
- at91_sys_write(AT91_ST_RTAR, last_crtr);
+ at91_st_write(AT91_ST_RTAR, last_crtr);
break;
case CLOCK_EVT_MODE_SHUTDOWN:
case CLOCK_EVT_MODE_UNUSED:
irqmask = 0;
break;
}
- at91_sys_write(AT91_ST_IER, irqmask);
+ at91_st_write(AT91_ST_IER, irqmask);
}
static int
alm = read_CRTR();
/* Cancel any pending alarm; flush any pending IRQ */
- at91_sys_write(AT91_ST_RTAR, alm);
- (void) at91_sys_read(AT91_ST_SR);
+ at91_st_write(AT91_ST_RTAR, alm);
+ at91_st_read(AT91_ST_SR);
/* Schedule alarm by writing RTAR. */
alm += delta;
- at91_sys_write(AT91_ST_RTAR, alm);
+ at91_st_write(AT91_ST_RTAR, alm);
return status;
}
.set_mode = clkevt32k_mode,
};
+void __iomem *at91_st_base;
+
+void __init at91rm9200_ioremap_st(u32 addr)
+{
+ at91_st_base = ioremap(addr, 256);
+ if (!at91_st_base)
+ panic("Impossible to ioremap ST\n");
+}
+
/*
* ST (system timer) module supports both clockevents and clocksource.
*/
void __init at91rm9200_timer_init(void)
{
/* Disable all timer interrupts, and clear any pending ones */
- at91_sys_write(AT91_ST_IDR,
+ at91_st_write(AT91_ST_IDR,
AT91_ST_PITS | AT91_ST_WDOVF | AT91_ST_RTTINC | AT91_ST_ALMS);
- (void) at91_sys_read(AT91_ST_SR);
+ at91_st_read(AT91_ST_SR);
/* Make IRQs happen for the system timer */
setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq);
* directly for the clocksource and all clockevents, after adjusting
* its prescaler from the 1 Hz default.
*/
- at91_sys_write(AT91_ST_RTMR, 1);
+ at91_st_write(AT91_ST_RTMR, 1);
/* Setup timer clockevent, with minimum of two ticks (important!!) */
clkevt.mult = div_sc(AT91_SLOW_CLOCK, NSEC_PER_SEC, clkevt.shift);
CLKDEV_CON_DEV_ID("usart", "fffd0000.serial", &usart3_clk),
CLKDEV_CON_DEV_ID("usart", "fffd4000.serial", &usart4_clk),
CLKDEV_CON_DEV_ID("usart", "fffd8000.serial", &usart5_clk),
+ /* more tc lookup table for DT entries */
+ CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
+ CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk),
+ CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk),
+ CLKDEV_CON_DEV_ID("t0_clk", "fffdc000.timer", &tc3_clk),
+ CLKDEV_CON_DEV_ID("t1_clk", "fffdc000.timer", &tc4_clk),
+ CLKDEV_CON_DEV_ID("t2_clk", "fffdc000.timer", &tc5_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
CLKDEV_CON_ID("pioA", &pioA_clk),
static void __init at91sam9260_map_io(void)
{
- if (cpu_is_at91sam9xe()) {
+ if (cpu_is_at91sam9xe())
at91sam9xe_map_io();
- } else if (cpu_is_at91sam9g20()) {
- at91_init_sram(0, AT91SAM9G20_SRAM0_BASE, AT91SAM9G20_SRAM0_SIZE);
- at91_init_sram(1, AT91SAM9G20_SRAM1_BASE, AT91SAM9G20_SRAM1_SIZE);
- } else {
- at91_init_sram(0, AT91SAM9260_SRAM0_BASE, AT91SAM9260_SRAM0_SIZE);
- at91_init_sram(1, AT91SAM9260_SRAM1_BASE, AT91SAM9260_SRAM1_SIZE);
- }
+ else if (cpu_is_at91sam9g20())
+ at91_init_sram(0, AT91SAM9G20_SRAM_BASE, AT91SAM9G20_SRAM_SIZE);
+ else
+ at91_init_sram(0, AT91SAM9260_SRAM_BASE, AT91SAM9260_SRAM_SIZE);
}
static void __init at91sam9260_ioremap_registers(void)
{
at91_ioremap_shdwc(AT91SAM9260_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9260_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9260_BASE_SDRAMC, 512);
at91sam926x_ioremap_pit(AT91SAM9260_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
-}
-
-static void at91sam9260_idle(void)
-{
- at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
- cpu_do_idle();
+ at91_ioremap_matrix(AT91SAM9260_BASE_MATRIX);
}
static void __init at91sam9260_initialize(void)
{
- arm_pm_idle = at91sam9260_idle;
+ arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9_alt_restart;
at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
| (1 << AT91SAM9260_ID_IRQ2);
#include <mach/cpu.h>
#include <mach/at91sam9260.h>
#include <mach/at91sam9260_matrix.h>
+#include <mach/at91_matrix.h>
#include <mach/at91sam9_smc.h>
#include "generic.h"
if (!data)
return;
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
+ csa = at91_matrix_read(AT91_MATRIX_EBICSA);
+ at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
if (gpio_is_valid(data->enable_pin))
static struct resource tcb0_resources[] = {
[0] = {
.start = AT91SAM9260_BASE_TCB0,
- .end = AT91SAM9260_BASE_TCB0 + SZ_16K - 1,
+ .end = AT91SAM9260_BASE_TCB0 + SZ_256 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
static struct resource tcb1_resources[] = {
[0] = {
.start = AT91SAM9260_BASE_TCB1,
- .end = AT91SAM9260_BASE_TCB1 + SZ_16K - 1,
+ .end = AT91SAM9260_BASE_TCB1 + SZ_256 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.num_resources = ARRAY_SIZE(tcb1_resources),
};
+#if defined(CONFIG_OF)
+static struct of_device_id tcb_ids[] = {
+ { .compatible = "atmel,at91rm9200-tcb" },
+ { /*sentinel*/ }
+};
+#endif
+
static void __init at91_add_device_tc(void)
{
+#if defined(CONFIG_OF)
+ struct device_node *np;
+
+ np = of_find_matching_node(NULL, tcb_ids);
+ if (np) {
+ of_node_put(np);
+ return;
+ }
+#endif
+
platform_device_register(&at91sam9260_tcb0_device);
platform_device_register(&at91sam9260_tcb1_device);
}
.start = AT91SAM9260_BASE_RTT,
.end = AT91SAM9260_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
- }
+ }, {
+ .flags = IORESOURCE_MEM,
+ },
};
static struct platform_device at91sam9260_rtt_device = {
.name = "at91_rtt",
.id = 0,
.resource = rtt_resources,
- .num_resources = ARRAY_SIZE(rtt_resources),
};
+
+#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
+static void __init at91_add_device_rtt_rtc(void)
+{
+ at91sam9260_rtt_device.name = "rtc-at91sam9";
+ /*
+ * The second resource is needed:
+ * GPBR will serve as the storage for RTC time offset
+ */
+ at91sam9260_rtt_device.num_resources = 2;
+ rtt_resources[1].start = AT91SAM9260_BASE_GPBR +
+ 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
+ rtt_resources[1].end = rtt_resources[1].start + 3;
+}
+#else
+static void __init at91_add_device_rtt_rtc(void)
+{
+ /* Only one resource is needed: RTT not used as RTC */
+ at91sam9260_rtt_device.num_resources = 1;
+}
+#endif
+
static void __init at91_add_device_rtt(void)
{
+ at91_add_device_rtt_rtc();
platform_device_register(&at91sam9260_rtt_device);
}
}
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-struct platform_device *atmel_default_console_device; /* the serial console device */
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
if (!data)
return;
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
+ csa = at91_matrix_read(AT91_MATRIX_EBICSA);
switch (data->chipselect) {
case 4:
return;
}
- at91_sys_write(AT91_MATRIX_EBICSA, csa);
+ at91_matrix_write(AT91_MATRIX_EBICSA, csa);
if (gpio_is_valid(data->rst_pin)) {
at91_set_multi_drive(data->rst_pin, 0);
{
at91_ioremap_shdwc(AT91SAM9261_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9261_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9261_BASE_SDRAMC, 512);
at91sam926x_ioremap_pit(AT91SAM9261_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
-}
-
-static void at91sam9261_idle(void)
-{
- at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
- cpu_do_idle();
+ at91_ioremap_matrix(AT91SAM9261_BASE_MATRIX);
}
static void __init at91sam9261_initialize(void)
{
- arm_pm_idle = at91sam9261_idle;
+ arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9_alt_restart;
at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1)
| (1 << AT91SAM9261_ID_IRQ2);
#include <mach/board.h>
#include <mach/at91sam9261.h>
#include <mach/at91sam9261_matrix.h>
+#include <mach/at91_matrix.h>
#include <mach/at91sam9_smc.h>
#include "generic.h"
if (!data)
return;
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
+ csa = at91_matrix_read(AT91_MATRIX_EBICSA);
+ at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
if (gpio_is_valid(data->enable_pin))
.start = AT91SAM9261_BASE_RTT,
.end = AT91SAM9261_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
+ }, {
+ .flags = IORESOURCE_MEM,
}
};
.name = "at91_rtt",
.id = 0,
.resource = rtt_resources,
- .num_resources = ARRAY_SIZE(rtt_resources),
};
+#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
+static void __init at91_add_device_rtt_rtc(void)
+{
+ at91sam9261_rtt_device.name = "rtc-at91sam9";
+ /*
+ * The second resource is needed:
+ * GPBR will serve as the storage for RTC time offset
+ */
+ at91sam9261_rtt_device.num_resources = 2;
+ rtt_resources[1].start = AT91SAM9261_BASE_GPBR +
+ 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
+ rtt_resources[1].end = rtt_resources[1].start + 3;
+}
+#else
+static void __init at91_add_device_rtt_rtc(void)
+{
+ /* Only one resource is needed: RTT not used as RTC */
+ at91sam9261_rtt_device.num_resources = 1;
+}
+#endif
+
static void __init at91_add_device_rtt(void)
{
+ at91_add_device_rtt_rtc();
platform_device_register(&at91sam9261_rtt_device);
}
}
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-struct platform_device *atmel_default_console_device; /* the serial console device */
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
{
at91_ioremap_shdwc(AT91SAM9263_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9263_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9263_BASE_SDRAMC0, 512);
+ at91_ioremap_ramc(1, AT91SAM9263_BASE_SDRAMC1, 512);
at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
-}
-
-static void at91sam9263_idle(void)
-{
- at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
- cpu_do_idle();
+ at91_ioremap_matrix(AT91SAM9263_BASE_MATRIX);
}
static void __init at91sam9263_initialize(void)
{
- arm_pm_idle = at91sam9263_idle;
+ arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9_alt_restart;
at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1);
#include <mach/board.h>
#include <mach/at91sam9263.h>
#include <mach/at91sam9263_matrix.h>
+#include <mach/at91_matrix.h>
#include <mach/at91sam9_smc.h>
#include "generic.h"
* we assume SMC timings are configured by board code,
* except True IDE where timings are controlled by driver
*/
- ebi0_csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
+ ebi0_csa = at91_matrix_read(AT91_MATRIX_EBI0CSA);
switch (data->chipselect) {
case 4:
at91_set_A_periph(AT91_PIN_PD6, 0); /* EBI0_NCS4/CFCS0 */
data->chipselect);
return;
}
- at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
+ at91_matrix_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
if (!data)
return;
- csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
- at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
+ csa = at91_matrix_read(AT91_MATRIX_EBI0CSA);
+ at91_matrix_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
/* enable pin */
if (gpio_is_valid(data->enable_pin))
.start = AT91SAM9263_BASE_RTT0,
.end = AT91SAM9263_BASE_RTT0 + SZ_16 - 1,
.flags = IORESOURCE_MEM,
+ }, {
+ .flags = IORESOURCE_MEM,
}
};
.name = "at91_rtt",
.id = 0,
.resource = rtt0_resources,
- .num_resources = ARRAY_SIZE(rtt0_resources),
};
static struct resource rtt1_resources[] = {
.start = AT91SAM9263_BASE_RTT1,
.end = AT91SAM9263_BASE_RTT1 + SZ_16 - 1,
.flags = IORESOURCE_MEM,
+ }, {
+ .flags = IORESOURCE_MEM,
}
};
.name = "at91_rtt",
.id = 1,
.resource = rtt1_resources,
- .num_resources = ARRAY_SIZE(rtt1_resources),
};
+#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
+static void __init at91_add_device_rtt_rtc(void)
+{
+ struct platform_device *pdev;
+ struct resource *r;
+
+ switch (CONFIG_RTC_DRV_AT91SAM9_RTT) {
+ case 0:
+ /*
+ * The second resource is needed only for the chosen RTT:
+ * GPBR will serve as the storage for RTC time offset
+ */
+ at91sam9263_rtt0_device.num_resources = 2;
+ at91sam9263_rtt1_device.num_resources = 1;
+ pdev = &at91sam9263_rtt0_device;
+ r = rtt0_resources;
+ break;
+ case 1:
+ at91sam9263_rtt0_device.num_resources = 1;
+ at91sam9263_rtt1_device.num_resources = 2;
+ pdev = &at91sam9263_rtt1_device;
+ r = rtt1_resources;
+ break;
+ default:
+ pr_err("at91sam9263: only supports 2 RTT (%d)\n",
+ CONFIG_RTC_DRV_AT91SAM9_RTT);
+ return;
+ }
+
+ pdev->name = "rtc-at91sam9";
+ r[1].start = AT91SAM9263_BASE_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
+ r[1].end = r[1].start + 3;
+}
+#else
+static void __init at91_add_device_rtt_rtc(void)
+{
+ /* Only one resource is needed: RTT not used as RTC */
+ at91sam9263_rtt0_device.num_resources = 1;
+ at91sam9263_rtt1_device.num_resources = 1;
+}
+#endif
+
static void __init at91_add_device_rtt(void)
{
+ at91_add_device_rtt_rtc();
platform_device_register(&at91sam9263_rtt0_device);
platform_device_register(&at91sam9263_rtt1_device);
}
}
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-struct platform_device *atmel_default_console_device; /* the serial console device */
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
#include <linux/kernel.h>
#include <linux/clk.h>
#include <linux/clockchips.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
#include <asm/mach/time.h>
static struct irqaction at91sam926x_pit_irq = {
.name = "at91_tick",
.flags = IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
- .handler = at91sam926x_pit_interrupt
+ .handler = at91sam926x_pit_interrupt,
+ .irq = AT91_ID_SYS,
};
static void at91sam926x_pit_reset(void)
pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
}
+#ifdef CONFIG_OF
+static struct of_device_id pit_timer_ids[] = {
+ { .compatible = "atmel,at91sam9260-pit" },
+ { /* sentinel */ }
+};
+
+static int __init of_at91sam926x_pit_init(void)
+{
+ struct device_node *np;
+ int ret;
+
+ np = of_find_matching_node(NULL, pit_timer_ids);
+ if (!np)
+ goto err;
+
+ pit_base_addr = of_iomap(np, 0);
+ if (!pit_base_addr)
+ goto node_err;
+
+ /* Get the interrupts property */
+ ret = irq_of_parse_and_map(np, 0);
+ if (!ret) {
+ pr_crit("AT91: PIT: Unable to get IRQ from DT\n");
+ goto ioremap_err;
+ }
+ at91sam926x_pit_irq.irq = ret;
+
+ of_node_put(np);
+
+ return 0;
+
+ioremap_err:
+ iounmap(pit_base_addr);
+node_err:
+ of_node_put(np);
+err:
+ return -EINVAL;
+}
+#else
+static int __init of_at91sam926x_pit_init(void)
+{
+ return -EINVAL;
+}
+#endif
+
/*
* Set up both clocksource and clockevent support.
*/
{
unsigned long pit_rate;
unsigned bits;
+ int ret;
+
+ /* For device tree enabled device: initialize here */
+ of_at91sam926x_pit_init();
/*
* Use our actual MCK to figure out how many MCK/16 ticks per
clocksource_register_hz(&pit_clk, pit_rate);
/* Set up irq handler */
- setup_irq(AT91_ID_SYS, &at91sam926x_pit_irq);
+ ret = setup_irq(at91sam926x_pit_irq.irq, &at91sam926x_pit_irq);
+ if (ret)
+ pr_crit("AT91: PIT: Unable to setup IRQ\n");
/* Set up and register clockevents */
pit_clkevt.mult = div_sc(pit_rate, NSEC_PER_SEC, pit_clkevt.shift);
void __init at91sam926x_ioremap_pit(u32 addr)
{
+#if defined(CONFIG_OF)
+ struct device_node *np =
+ of_find_matching_node(NULL, pit_timer_ids);
+
+ if (np) {
+ of_node_put(np);
+ return;
+ }
+#endif
pit_base_addr = ioremap(addr, 16);
if (!pit_base_addr)
#include <linux/linkage.h>
#include <mach/hardware.h>
-#include <mach/at91sam9_sdramc.h>
+#include <mach/at91_ramc.h>
#include <mach/at91_rstc.h>
.arm
.globl at91sam9_alt_restart
-at91sam9_alt_restart: ldr r0, .at91_va_base_sdramc @ preload constants
- ldr r1, =at91_rstc_base
- ldr r1, [r1]
+at91sam9_alt_restart: ldr r0, =at91_ramc_base @ preload constants
+ ldr r0, [r0]
+ ldr r4, =at91_rstc_base
+ ldr r1, [r4]
mov r2, #1
mov r3, #AT91_SDRAMC_LPCB_POWER_DOWN
str r4, [r1, #AT91_RSTC_CR] @ reset processor
b .
-
-.at91_va_base_sdramc:
- .word AT91_VA_BASE_SYS + AT91_SDRAMC0
CLKDEV_CON_DEV_ID("usart", "fff90000.serial", &usart1_clk),
CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk),
CLKDEV_CON_DEV_ID("usart", "fff98000.serial", &usart3_clk),
+ /* more tc lookup table for DT entries */
+ CLKDEV_CON_DEV_ID("t0_clk", "fff7c000.timer", &tcb0_clk),
+ CLKDEV_CON_DEV_ID("t0_clk", "fffd4000.timer", &tcb0_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk),
CLKDEV_CON_ID("pioA", &pioA_clk),
}
};
-static void at91sam9g45_idle(void)
-{
- at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
- cpu_do_idle();
-}
-
/* --------------------------------------------------------------------
* AT91SAM9G45 processor initialization
* -------------------------------------------------------------------- */
{
at91_ioremap_shdwc(AT91SAM9G45_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9G45_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9G45_BASE_DDRSDRC1, 512);
+ at91_ioremap_ramc(1, AT91SAM9G45_BASE_DDRSDRC0, 512);
at91sam926x_ioremap_pit(AT91SAM9G45_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9G45_BASE_SMC);
+ at91_ioremap_matrix(AT91SAM9G45_BASE_MATRIX);
}
static void __init at91sam9g45_initialize(void)
{
- arm_pm_idle = at91sam9g45_idle;
+ arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9g45_restart;
at91_extern_irq = (1 << AT91SAM9G45_ID_IRQ0);
#include <mach/board.h>
#include <mach/at91sam9g45.h>
#include <mach/at91sam9g45_matrix.h>
+#include <mach/at91_matrix.h>
#include <mach/at91sam9_smc.h>
#include <mach/at_hdmac.h>
#include <mach/atmel-mci.h>
if (!data)
return;
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
+ csa = at91_matrix_read(AT91_MATRIX_EBICSA);
+ at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
/* enable pin */
if (gpio_is_valid(data->enable_pin))
static struct resource tcb0_resources[] = {
[0] = {
.start = AT91SAM9G45_BASE_TCB0,
- .end = AT91SAM9G45_BASE_TCB0 + SZ_16K - 1,
+ .end = AT91SAM9G45_BASE_TCB0 + SZ_256 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
static struct resource tcb1_resources[] = {
[0] = {
.start = AT91SAM9G45_BASE_TCB1,
- .end = AT91SAM9G45_BASE_TCB1 + SZ_16K - 1,
+ .end = AT91SAM9G45_BASE_TCB1 + SZ_256 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.num_resources = ARRAY_SIZE(tcb1_resources),
};
+#if defined(CONFIG_OF)
+static struct of_device_id tcb_ids[] = {
+ { .compatible = "atmel,at91rm9200-tcb" },
+ { /*sentinel*/ }
+};
+#endif
+
static void __init at91_add_device_tc(void)
{
+#if defined(CONFIG_OF)
+ struct device_node *np;
+
+ np = of_find_matching_node(NULL, tcb_ids);
+ if (np) {
+ of_node_put(np);
+ return;
+ }
+#endif
+
platform_device_register(&at91sam9g45_tcb0_device);
platform_device_register(&at91sam9g45_tcb1_device);
}
.start = AT91SAM9G45_BASE_RTT,
.end = AT91SAM9G45_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
+ }, {
+ .flags = IORESOURCE_MEM,
}
};
.name = "at91_rtt",
.id = 0,
.resource = rtt_resources,
- .num_resources = ARRAY_SIZE(rtt_resources),
};
+#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
+static void __init at91_add_device_rtt_rtc(void)
+{
+ at91sam9g45_rtt_device.name = "rtc-at91sam9";
+ /*
+ * The second resource is needed:
+ * GPBR will serve as the storage for RTC time offset
+ */
+ at91sam9g45_rtt_device.num_resources = 2;
+ rtt_resources[1].start = AT91SAM9G45_BASE_GPBR +
+ 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
+ rtt_resources[1].end = rtt_resources[1].start + 3;
+}
+#else
+static void __init at91_add_device_rtt_rtc(void)
+{
+ /* Only one resource is needed: RTT not used as RTC */
+ at91sam9g45_rtt_device.num_resources = 1;
+}
+#endif
+
static void __init at91_add_device_rtt(void)
{
+ at91_add_device_rtt_rtc();
platform_device_register(&at91sam9g45_rtt_device);
}
}
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-struct platform_device *atmel_default_console_device; /* the serial console device */
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
#include <linux/linkage.h>
#include <mach/hardware.h>
-#include <mach/at91sam9_ddrsdr.h>
+#include <mach/at91_ramc.h>
#include <mach/at91_rstc.h>
.arm
.globl at91sam9g45_restart
at91sam9g45_restart:
- ldr r0, .at91_va_base_sdramc0 @ preload constants
- ldr r1, =at91_rstc_base
- ldr r1, [r1]
+ ldr r5, =at91_ramc_base @ preload constants
+ ldr r0, [r5]
+ ldr r4, =at91_rstc_base
+ ldr r1, [r4]
mov r2, #1
mov r3, #AT91_DDRSDRC_LPCB_POWER_DOWN
str r4, [r1, #AT91_RSTC_CR] @ reset processor
b .
-
-.at91_va_base_sdramc0:
- .word AT91_VA_BASE_SYS + AT91_DDRSDRC0
{
at91_ioremap_shdwc(AT91SAM9RL_BASE_SHDWC);
at91_ioremap_rstc(AT91SAM9RL_BASE_RSTC);
+ at91_ioremap_ramc(0, AT91SAM9RL_BASE_SDRAMC, 512);
at91sam926x_ioremap_pit(AT91SAM9RL_BASE_PIT);
at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC);
-}
-
-static void at91sam9rl_idle(void)
-{
- at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
- cpu_do_idle();
+ at91_ioremap_matrix(AT91SAM9RL_BASE_MATRIX);
}
static void __init at91sam9rl_initialize(void)
{
- arm_pm_idle = at91sam9rl_idle;
+ arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9_alt_restart;
at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0);
#include <mach/board.h>
#include <mach/at91sam9rl.h>
#include <mach/at91sam9rl_matrix.h>
+#include <mach/at91_matrix.h>
#include <mach/at91sam9_smc.h>
#include <mach/at_hdmac.h>
if (!data)
return;
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
+ csa = at91_matrix_read(AT91_MATRIX_EBICSA);
+ at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
if (gpio_is_valid(data->enable_pin))
.start = AT91SAM9RL_BASE_RTT,
.end = AT91SAM9RL_BASE_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
+ }, {
+ .flags = IORESOURCE_MEM,
}
};
.name = "at91_rtt",
.id = 0,
.resource = rtt_resources,
- .num_resources = ARRAY_SIZE(rtt_resources),
};
+#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
+static void __init at91_add_device_rtt_rtc(void)
+{
+ at91sam9rl_rtt_device.name = "rtc-at91sam9";
+ /*
+ * The second resource is needed:
+ * GPBR will serve as the storage for RTC time offset
+ */
+ at91sam9rl_rtt_device.num_resources = 2;
+ rtt_resources[1].start = AT91SAM9RL_BASE_GPBR +
+ 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
+ rtt_resources[1].end = rtt_resources[1].start + 3;
+}
+#else
+static void __init at91_add_device_rtt_rtc(void)
+{
+ /* Only one resource is needed: RTT not used as RTC */
+ at91sam9rl_rtt_device.num_resources = 1;
+}
+#endif
+
static void __init at91_add_device_rtt(void)
{
+ at91_add_device_rtt_rtc();
platform_device_register(&at91sam9rl_rtt_device);
}
}
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-struct platform_device *atmel_default_console_device; /* the serial console device */
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
static void __init at91sam9x5_ioremap_registers(void)
{
- if (of_at91sam926x_pit_init() < 0)
- panic("Impossible to find PIT\n");
+ at91_ioremap_ramc(0, AT91SAM9X5_BASE_DDRSDRC0, 512);
}
void __init at91sam9x5_initialize(void)
/* --------------------------------------------------------------------
* AT91SAM9x5 devices (temporary before modification of code)
* -------------------------------------------------------------------- */
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
-struct platform_device *atmel_default_console_device = NULL;
-
void __init at91_add_device_nand(struct atmel_nand_data *data) {}
/* --------------------------------------------------------------------
* Disable the processor clock. The processor will be automatically
* re-enabled by an interrupt or by a reset.
*/
- at91_sys_write(AT91_PS_CR, AT91_PS_CR_CPU);
+ __raw_writel(AT91_PS_CR_CPU, AT91_PS_CR);
cpu_do_idle();
}
#include <asm/mach/time.h>
#include <mach/at91_tc.h>
+#define at91_tc_read(field) \
+ __raw_readl(AT91_TC + field)
+
+#define at91_tc_write(field, value) \
+ __raw_writel(value, AT91_TC + field);
+
/*
* 3 counter/timer units present.
*/
static unsigned long at91x40_gettimeoffset(void)
{
- return (at91_sys_read(AT91_TC + AT91_TC_CLK1BASE + AT91_TC_CV) * 1000000 / (AT91X40_MASTER_CLOCK / 128));
+ return (at91_tc_read(AT91_TC_CLK1BASE + AT91_TC_CV) * 1000000 / (AT91X40_MASTER_CLOCK / 128));
}
static irqreturn_t at91x40_timer_interrupt(int irq, void *dev_id)
{
- at91_sys_read(AT91_TC + AT91_TC_CLK1BASE + AT91_TC_SR);
+ at91_tc_read(AT91_TC_CLK1BASE + AT91_TC_SR);
timer_tick();
return IRQ_HANDLED;
}
{
unsigned int v;
- at91_sys_write(AT91_TC + AT91_TC_BCR, 0);
- v = at91_sys_read(AT91_TC + AT91_TC_BMR);
+ at91_tc_write(AT91_TC_BCR, 0);
+ v = at91_tc_read(AT91_TC_BMR);
v = (v & ~AT91_TC_TC1XC1S) | AT91_TC_TC1XC1S_NONE;
- at91_sys_write(AT91_TC + AT91_TC_BMR, v);
+ at91_tc_write(AT91_TC_BMR, v);
- at91_sys_write(AT91_TC + AT91_TC_CLK1BASE + AT91_TC_CCR, AT91_TC_CLKDIS);
- at91_sys_write(AT91_TC + AT91_TC_CLK1BASE + AT91_TC_CMR, (AT91_TC_TIMER_CLOCK4 | AT91_TC_CPCTRG));
- at91_sys_write(AT91_TC + AT91_TC_CLK1BASE + AT91_TC_IDR, 0xffffffff);
- at91_sys_write(AT91_TC + AT91_TC_CLK1BASE + AT91_TC_RC, (AT91X40_MASTER_CLOCK / 128) / HZ - 1);
- at91_sys_write(AT91_TC + AT91_TC_CLK1BASE + AT91_TC_IER, (1<<4));
+ at91_tc_write(AT91_TC_CLK1BASE + AT91_TC_CCR, AT91_TC_CLKDIS);
+ at91_tc_write(AT91_TC_CLK1BASE + AT91_TC_CMR, (AT91_TC_TIMER_CLOCK4 | AT91_TC_CPCTRG));
+ at91_tc_write(AT91_TC_CLK1BASE + AT91_TC_IDR, 0xffffffff);
+ at91_tc_write(AT91_TC_CLK1BASE + AT91_TC_RC, (AT91X40_MASTER_CLOCK / 128) / HZ - 1);
+ at91_tc_write(AT91_TC_CLK1BASE + AT91_TC_IER, (1<<4));
setup_irq(AT91X40_ID_TC1, &at91x40_timer_irq);
- at91_sys_write(AT91_TC + AT91_TC_CLK1BASE + AT91_TC_CCR, (AT91_TC_SWTRG | AT91_TC_CLKEN));
+ at91_tc_write(AT91_TC_CLK1BASE + AT91_TC_CCR, (AT91_TC_SWTRG | AT91_TC_CLKEN));
}
struct sys_timer at91x40_timer = {
#include <mach/board.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91sam9260_matrix.h>
+#include <mach/at91_matrix.h>
#include "sam9_smc.h"
#include "generic.h"
{
unsigned long csa;
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V);
+ csa = at91_matrix_read(AT91_MATRIX_EBICSA);
+ at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V);
/* configure chip-select 0 (NOR) */
sam9_smc_configure(0, 0, &cpu9krea_nor_smc_config);
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include <mach/cpu.h>
#include "generic.h"
#include <linux/init.h>
#include <linux/module.h>
#include <linux/gpio.h>
-#include <linux/irqdomain.h>
+#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
{
/* Initialize processor: 12.000 MHz crystal */
at91_initialize(12000000);
-
- /* DGBU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
}
/* det_pin is not connected */
at91_add_device_nand(&ek_nand_data);
}
-static const struct of_device_id aic_of_match[] __initconst = {
- { .compatible = "atmel,at91rm9200-aic", },
- {},
+static const struct of_device_id irq_of_match[] __initconst = {
+
+ { .compatible = "atmel,at91rm9200-aic", .data = at91_aic_of_init },
+ { .compatible = "atmel,at91rm9200-gpio", .data = at91_gpio_of_irq_setup },
+ { .compatible = "atmel,at91sam9x5-gpio", .data = at91_gpio_of_irq_setup },
+ { /*sentinel*/ }
};
static void __init at91_dt_init_irq(void)
{
- irq_domain_generate_simple(aic_of_match, 0xfffff000, 0);
- at91_init_irq_default();
+ of_irq_init(irq_of_match);
}
static void __init at91_dt_device_init(void)
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include <mach/cpu.h>
#include "generic.h"
at91_add_device_mmc(0, &eco920_mmc_data);
platform_device_register(&eco920_flash);
- at91_sys_write(AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1)
+ at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1)
| AT91_SMC_RWSETUP_(1)
| AT91_SMC_DBW_8
| AT91_SMC_WSEN
at91_set_deglitch(AT91_PIN_PA23, 1);
/* Initialization of the Static Memory Controller for Chip Select 3 */
- at91_sys_write(AT91_SMC_CSR(3),
+ at91_ramc_write(0, AT91_SMC_CSR(3),
AT91_SMC_DBW_16 | /* 16 bit */
AT91_SMC_WSEN |
AT91_SMC_NWS_(5) | /* wait states */
#include <mach/board.h>
#include <mach/cpu.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include "generic.h"
/* Audio codec */
I2C_BOARD_INFO("tlv320aic23", 0x1a),
},
- {
+};
+
+static struct i2c_board_info __initdata snapper9260_i2c_isl1208 = {
/* RTC */
I2C_BOARD_INFO("isl1208", 0x6f),
- .irq = gpio_to_irq(AT91_PIN_PA31),
- },
};
static void __init snapper9260_add_device_nand(void)
{
at91_add_device_i2c(snapper9260_i2c_devices,
ARRAY_SIZE(snapper9260_i2c_devices));
+
+ snapper9260_i2c_isl1208.irq = gpio_to_irq(AT91_PIN_PA31);
+ i2c_register_board_info(0, &snapper9260_i2c_isl1208, 1);
+
at91_add_device_serial();
at91_add_device_usbh(&snapper9260_usbh_data);
at91_add_device_udc(&snapper9260_udc_data);
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
#include <mach/cpu.h>
#include "generic.h"
at91_set_A_periph(AT91_PIN_PC6, 0);
/* Initialization of the Static Memory Controller for Chip Select 2 */
- at91_sys_write(AT91_SMC_CSR(2), AT91_SMC_DBW_16 /* 16 bit */
+ at91_ramc_write(0, AT91_SMC_CSR(2), AT91_SMC_DBW_16 /* 16 bit */
| AT91_SMC_WSEN | AT91_SMC_NWS_(0x4) /* wait states */
| AT91_SMC_TDF_(0x100) /* float time */
);
#include <mach/at91_pmc.h>
#include <mach/cpu.h>
+#include <asm/proc-fns.h>
+
#include "clock.h"
#include "generic.h"
+void __iomem *at91_pmc_base;
/*
* There's a lot more which can be done with clocks, including cpufreq
value = 0;
// REVISIT: Add work-around for AT91RM9200 Errata #26 ?
- at91_sys_write(AT91_CKGR_PLLBR, value);
+ at91_pmc_write(AT91_CKGR_PLLBR, value);
do {
cpu_relax();
- } while ((at91_sys_read(AT91_PMC_SR) & AT91_PMC_LOCKB) != is_on);
+ } while ((at91_pmc_read(AT91_PMC_SR) & AT91_PMC_LOCKB) != is_on);
}
static struct clk pllb = {
static void pmc_sys_mode(struct clk *clk, int is_on)
{
if (is_on)
- at91_sys_write(AT91_PMC_SCER, clk->pmc_mask);
+ at91_pmc_write(AT91_PMC_SCER, clk->pmc_mask);
else
- at91_sys_write(AT91_PMC_SCDR, clk->pmc_mask);
+ at91_pmc_write(AT91_PMC_SCDR, clk->pmc_mask);
}
static void pmc_uckr_mode(struct clk *clk, int is_on)
{
- unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
+ unsigned int uckr = at91_pmc_read(AT91_CKGR_UCKR);
if (is_on) {
is_on = AT91_PMC_LOCKU;
- at91_sys_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask);
+ at91_pmc_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask);
} else
- at91_sys_write(AT91_CKGR_UCKR, uckr & ~(clk->pmc_mask));
+ at91_pmc_write(AT91_CKGR_UCKR, uckr & ~(clk->pmc_mask));
do {
cpu_relax();
- } while ((at91_sys_read(AT91_PMC_SR) & AT91_PMC_LOCKU) != is_on);
+ } while ((at91_pmc_read(AT91_PMC_SR) & AT91_PMC_LOCKU) != is_on);
}
/* USB function clocks (PLLB must be 48 MHz) */
static void pmc_periph_mode(struct clk *clk, int is_on)
{
if (is_on)
- at91_sys_write(AT91_PMC_PCER, clk->pmc_mask);
+ at91_pmc_write(AT91_PMC_PCER, clk->pmc_mask);
else
- at91_sys_write(AT91_PMC_PCDR, clk->pmc_mask);
+ at91_pmc_write(AT91_PMC_PCDR, clk->pmc_mask);
}
static struct clk __init *at91_css_to_clk(unsigned long css)
if (actual && actual <= rate) {
u32 pckr;
- pckr = at91_sys_read(AT91_PMC_PCKR(clk->id));
+ pckr = at91_pmc_read(AT91_PMC_PCKR(clk->id));
pckr &= css_mask; /* keep clock selection */
pckr |= prescale << prescale_offset;
- at91_sys_write(AT91_PMC_PCKR(clk->id), pckr);
+ at91_pmc_write(AT91_PMC_PCKR(clk->id), pckr);
clk->rate_hz = actual;
break;
}
clk->rate_hz = parent->rate_hz;
clk->parent = parent;
- at91_sys_write(AT91_PMC_PCKR(clk->id), parent->id);
+ at91_pmc_write(AT91_PMC_PCKR(clk->id), parent->id);
spin_unlock_irqrestore(&clk_lock, flags);
return 0;
else
css_mask = AT91_PMC_CSS;
- pckr = at91_sys_read(AT91_PMC_PCKR(clk->id));
+ pckr = at91_pmc_read(AT91_PMC_PCKR(clk->id));
parent = at91_css_to_clk(pckr & css_mask);
clk->parent = parent;
clk->rate_hz = parent->rate_hz / pmc_prescaler_divider(pckr);
u32 scsr, pcsr, uckr = 0, sr;
struct clk *clk;
- seq_printf(s, "SCSR = %8x\n", scsr = at91_sys_read(AT91_PMC_SCSR));
- seq_printf(s, "PCSR = %8x\n", pcsr = at91_sys_read(AT91_PMC_PCSR));
- seq_printf(s, "MOR = %8x\n", at91_sys_read(AT91_CKGR_MOR));
- seq_printf(s, "MCFR = %8x\n", at91_sys_read(AT91_CKGR_MCFR));
- seq_printf(s, "PLLA = %8x\n", at91_sys_read(AT91_CKGR_PLLAR));
+ scsr = at91_pmc_read(AT91_PMC_SCSR);
+ pcsr = at91_pmc_read(AT91_PMC_PCSR);
+ sr = at91_pmc_read(AT91_PMC_SR);
+ seq_printf(s, "SCSR = %8x\n", scsr);
+ seq_printf(s, "PCSR = %8x\n", pcsr);
+ seq_printf(s, "MOR = %8x\n", at91_pmc_read(AT91_CKGR_MOR));
+ seq_printf(s, "MCFR = %8x\n", at91_pmc_read(AT91_CKGR_MCFR));
+ seq_printf(s, "PLLA = %8x\n", at91_pmc_read(AT91_CKGR_PLLAR));
if (cpu_has_pllb())
- seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR));
- if (cpu_has_utmi())
- seq_printf(s, "UCKR = %8x\n", uckr = at91_sys_read(AT91_CKGR_UCKR));
- seq_printf(s, "MCKR = %8x\n", at91_sys_read(AT91_PMC_MCKR));
+ seq_printf(s, "PLLB = %8x\n", at91_pmc_read(AT91_CKGR_PLLBR));
+ if (cpu_has_utmi()) {
+ uckr = at91_pmc_read(AT91_CKGR_UCKR);
+ seq_printf(s, "UCKR = %8x\n", uckr);
+ }
+ seq_printf(s, "MCKR = %8x\n", at91_pmc_read(AT91_PMC_MCKR));
if (cpu_has_upll())
- seq_printf(s, "USB = %8x\n", at91_sys_read(AT91_PMC_USB));
- seq_printf(s, "SR = %8x\n", sr = at91_sys_read(AT91_PMC_SR));
+ seq_printf(s, "USB = %8x\n", at91_pmc_read(AT91_PMC_USB));
+ seq_printf(s, "SR = %8x\n", sr);
seq_printf(s, "\n");
if (cpu_is_at91rm9200()) {
uhpck.pmc_mask = AT91RM9200_PMC_UHP;
udpck.pmc_mask = AT91RM9200_PMC_UDP;
- at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
+ at91_pmc_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() ||
cpu_is_at91sam9263() || cpu_is_at91sam9g20() ||
cpu_is_at91sam9g10()) {
uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
udpck.pmc_mask = AT91SAM926x_PMC_UDP;
}
- at91_sys_write(AT91_CKGR_PLLBR, 0);
+ at91_pmc_write(AT91_CKGR_PLLBR, 0);
udpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init);
uhpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init);
/* Setup divider by 10 to reach 48 MHz */
usbr |= ((10 - 1) << 8) & AT91_PMC_OHCIUSBDIV;
- at91_sys_write(AT91_PMC_USB, usbr);
+ at91_pmc_write(AT91_PMC_USB, usbr);
/* Now set uhpck values */
uhpck.parent = &utmi_clk;
uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
uhpck.rate_hz = utmi_clk.rate_hz;
- uhpck.rate_hz /= 1 + ((at91_sys_read(AT91_PMC_USB) & AT91_PMC_OHCIUSBDIV) >> 8);
+ uhpck.rate_hz /= 1 + ((at91_pmc_read(AT91_PMC_USB) & AT91_PMC_OHCIUSBDIV) >> 8);
}
int __init at91_clock_init(unsigned long main_clock)
int i;
int pll_overclock = false;
+ at91_pmc_base = ioremap(AT91_PMC, 256);
+ if (!at91_pmc_base)
+ panic("Impossible to ioremap AT91_PMC 0x%x\n", AT91_PMC);
+
/*
* When the bootloader initialized the main oscillator correctly,
* there's no problem using the cycle counter. But if it didn't,
*/
if (!main_clock) {
do {
- tmp = at91_sys_read(AT91_CKGR_MCFR);
+ tmp = at91_pmc_read(AT91_CKGR_MCFR);
} while (!(tmp & AT91_PMC_MAINRDY));
main_clock = (tmp & AT91_PMC_MAINF) * (AT91_SLOW_CLOCK / 16);
}
main_clk.rate_hz = main_clock;
/* report if PLLA is more than mildly overclocked */
- plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR));
+ plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_pmc_read(AT91_CKGR_PLLAR));
if (cpu_has_300M_plla()) {
if (plla.rate_hz > 300000000)
pll_overclock = true;
pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
if (cpu_has_plladiv2()) {
- mckr = at91_sys_read(AT91_PMC_MCKR);
+ mckr = at91_pmc_read(AT91_PMC_MCKR);
plla.rate_hz /= (1 << ((mckr & AT91_PMC_PLLADIV2) >> 12)); /* plla divisor by 2 */
}
* MCK and CPU derive from one of those primary clocks.
* For now, assume this parentage won't change.
*/
- mckr = at91_sys_read(AT91_PMC_MCKR);
+ mckr = at91_pmc_read(AT91_PMC_MCKR);
mck.parent = at91_css_to_clk(mckr & AT91_PMC_CSS);
freq = mck.parent->rate_hz;
freq /= pmc_prescaler_divider(mckr); /* prescale */
pr_debug("Clocks: disable unused %s\n", clk->name);
}
- at91_sys_write(AT91_PMC_PCDR, pcdr);
- at91_sys_write(AT91_PMC_SCDR, scdr);
+ at91_pmc_write(AT91_PMC_PCDR, pcdr);
+ at91_pmc_write(AT91_PMC_SCDR, scdr);
return 0;
}
late_initcall(at91_clock_reset);
+
+void at91sam9_idle(void)
+{
+ at91_pmc_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+ cpu_do_idle();
+}
*/
#include <linux/clkdev.h>
+#include <linux/of.h>
/* Map io */
extern void __init at91_map_io(void);
extern void __init at91_init_interrupts(unsigned int priority[]);
extern void __init at91x40_init_interrupts(unsigned int priority[]);
extern void __init at91_aic_init(unsigned int priority[]);
+extern int __init at91_aic_of_init(struct device_node *node,
+ struct device_node *parent);
+
/* Timer */
struct sys_timer;
+extern void at91rm9200_ioremap_st(u32 addr);
extern struct sys_timer at91rm9200_timer;
extern void at91sam926x_ioremap_pit(u32 addr);
extern struct sys_timer at91sam926x_timer;
extern void at91_irq_suspend(void);
extern void at91_irq_resume(void);
+/* idle */
+extern void at91sam9_idle(void);
+
/* reset */
extern void at91_ioremap_rstc(u32 base_addr);
extern void at91sam9_alt_restart(char, const char *);
/* shutdown */
extern void at91_ioremap_shdwc(u32 base_addr);
+/* Matrix */
+extern void at91_ioremap_matrix(u32 base_addr);
+
+/* Ram Controler */
+extern void at91_ioremap_ramc(int id, u32 addr, u32 size);
+
/* GPIO */
#define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */
#define AT91RM9200_BGA 4 /* AT91RM9200 BGA package has 4 banks */
};
extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks);
extern void __init at91_gpio_irq_setup(void);
+extern int __init at91_gpio_of_irq_setup(struct device_node *node,
+ struct device_node *parent);
extern int at91_extern_irq;
#include <linux/clk.h>
#include <linux/errno.h>
+#include <linux/device.h>
#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/io.h>
+#include <linux/irqdomain.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
#include <mach/hardware.h>
#include <mach/at91_pio.h>
struct at91_gpio_chip {
struct gpio_chip chip;
struct at91_gpio_chip *next; /* Bank sharing same clock */
- int id; /* ID of register bank */
- void __iomem *regbase; /* Base of register bank */
+ int pioc_hwirq; /* PIO bank interrupt identifier on AIC */
+ int pioc_virq; /* PIO bank Linux virtual interrupt */
+ int pioc_idx; /* PIO bank index */
+ void __iomem *regbase; /* PIO bank virtual address */
struct clk *clock; /* associated clock */
+ struct irq_domain *domain; /* associated irq domain */
};
#define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip)
unsigned offset, int val);
static int at91_gpiolib_direction_input(struct gpio_chip *chip,
unsigned offset);
+static int at91_gpiolib_to_irq(struct gpio_chip *chip, unsigned offset);
-#define AT91_GPIO_CHIP(name, base_gpio, nr_gpio) \
+#define AT91_GPIO_CHIP(name, nr_gpio) \
{ \
.chip = { \
.label = name, \
.get = at91_gpiolib_get, \
.set = at91_gpiolib_set, \
.dbg_show = at91_gpiolib_dbg_show, \
- .base = base_gpio, \
+ .to_irq = at91_gpiolib_to_irq, \
.ngpio = nr_gpio, \
}, \
}
static struct at91_gpio_chip gpio_chip[] = {
- AT91_GPIO_CHIP("pioA", 0x00, 32),
- AT91_GPIO_CHIP("pioB", 0x20, 32),
- AT91_GPIO_CHIP("pioC", 0x40, 32),
- AT91_GPIO_CHIP("pioD", 0x60, 32),
- AT91_GPIO_CHIP("pioE", 0x80, 32),
+ AT91_GPIO_CHIP("pioA", 32),
+ AT91_GPIO_CHIP("pioB", 32),
+ AT91_GPIO_CHIP("pioC", 32),
+ AT91_GPIO_CHIP("pioD", 32),
+ AT91_GPIO_CHIP("pioE", 32),
};
static int gpio_banks;
+static unsigned long at91_gpio_caps;
+
+/* All PIO controllers support PIO3 features */
+#define AT91_GPIO_CAP_PIO3 (1 << 0)
+
+#define has_pio3() (at91_gpio_caps & AT91_GPIO_CAP_PIO3)
+
+/*--------------------------------------------------------------------------*/
static inline void __iomem *pin_to_controller(unsigned pin)
{
}
+static char peripheral_function(void __iomem *pio, unsigned mask)
+{
+ char ret = 'X';
+ u8 select;
+
+ if (pio) {
+ if (has_pio3()) {
+ select = !!(__raw_readl(pio + PIO_ABCDSR1) & mask);
+ select |= (!!(__raw_readl(pio + PIO_ABCDSR2) & mask) << 1);
+ ret = 'A' + select;
+ } else {
+ ret = __raw_readl(pio + PIO_ABSR) & mask ?
+ 'B' : 'A';
+ }
+ }
+
+ return ret;
+}
+
/*--------------------------------------------------------------------------*/
/* Not all hardware capabilities are exposed through these calls; they
__raw_writel(mask, pio + PIO_IDR);
__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
- __raw_writel(mask, pio + PIO_ASR);
+ if (has_pio3()) {
+ __raw_writel(__raw_readl(pio + PIO_ABCDSR1) & ~mask,
+ pio + PIO_ABCDSR1);
+ __raw_writel(__raw_readl(pio + PIO_ABCDSR2) & ~mask,
+ pio + PIO_ABCDSR2);
+ } else {
+ __raw_writel(mask, pio + PIO_ASR);
+ }
__raw_writel(mask, pio + PIO_PDR);
return 0;
}
__raw_writel(mask, pio + PIO_IDR);
__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
- __raw_writel(mask, pio + PIO_BSR);
+ if (has_pio3()) {
+ __raw_writel(__raw_readl(pio + PIO_ABCDSR1) | mask,
+ pio + PIO_ABCDSR1);
+ __raw_writel(__raw_readl(pio + PIO_ABCDSR2) & ~mask,
+ pio + PIO_ABCDSR2);
+ } else {
+ __raw_writel(mask, pio + PIO_BSR);
+ }
__raw_writel(mask, pio + PIO_PDR);
return 0;
}
/*
- * mux the pin to the gpio controller (instead of "A" or "B" peripheral), and
- * configure it for an input.
+ * mux the pin to the "C" internal peripheral role.
+ */
+int __init_or_module at91_set_C_periph(unsigned pin, int use_pullup)
+{
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
+
+ if (!pio || !has_pio3())
+ return -EINVAL;
+
+ __raw_writel(mask, pio + PIO_IDR);
+ __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
+ __raw_writel(__raw_readl(pio + PIO_ABCDSR1) & ~mask, pio + PIO_ABCDSR1);
+ __raw_writel(__raw_readl(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2);
+ __raw_writel(mask, pio + PIO_PDR);
+ return 0;
+}
+EXPORT_SYMBOL(at91_set_C_periph);
+
+
+/*
+ * mux the pin to the "D" internal peripheral role.
+ */
+int __init_or_module at91_set_D_periph(unsigned pin, int use_pullup)
+{
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
+
+ if (!pio || !has_pio3())
+ return -EINVAL;
+
+ __raw_writel(mask, pio + PIO_IDR);
+ __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
+ __raw_writel(__raw_readl(pio + PIO_ABCDSR1) | mask, pio + PIO_ABCDSR1);
+ __raw_writel(__raw_readl(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2);
+ __raw_writel(mask, pio + PIO_PDR);
+ return 0;
+}
+EXPORT_SYMBOL(at91_set_D_periph);
+
+
+/*
+ * mux the pin to the gpio controller (instead of "A", "B", "C"
+ * or "D" peripheral), and configure it for an input.
*/
int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup)
{
/*
- * mux the pin to the gpio controller (instead of "A" or "B" peripheral),
- * and configure it for an output.
+ * mux the pin to the gpio controller (instead of "A", "B", "C"
+ * or "D" peripheral), and configure it for an output.
*/
int __init_or_module at91_set_gpio_output(unsigned pin, int value)
{
if (!pio)
return -EINVAL;
+
+ if (has_pio3() && is_on)
+ __raw_writel(mask, pio + PIO_IFSCDR);
__raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR));
return 0;
}
EXPORT_SYMBOL(at91_set_deglitch);
/*
+ * enable/disable the debounce filter;
+ */
+int __init_or_module at91_set_debounce(unsigned pin, int is_on, int div)
+{
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
+
+ if (!pio || !has_pio3())
+ return -EINVAL;
+
+ if (is_on) {
+ __raw_writel(mask, pio + PIO_IFSCER);
+ __raw_writel(div & PIO_SCDR_DIV, pio + PIO_SCDR);
+ __raw_writel(mask, pio + PIO_IFER);
+ } else {
+ __raw_writel(mask, pio + PIO_IFDR);
+ }
+ return 0;
+}
+EXPORT_SYMBOL(at91_set_debounce);
+
+/*
* enable/disable the multi-driver; This is only valid for output and
* allows the output pin to run as an open collector output.
*/
EXPORT_SYMBOL(at91_set_multi_drive);
/*
+ * enable/disable the pull-down.
+ * If pull-up already enabled while calling the function, we disable it.
+ */
+int __init_or_module at91_set_pulldown(unsigned pin, int is_on)
+{
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
+
+ if (!pio || !has_pio3())
+ return -EINVAL;
+
+ /* Disable pull-up anyway */
+ __raw_writel(mask, pio + PIO_PUDR);
+ __raw_writel(mask, pio + (is_on ? PIO_PPDER : PIO_PPDDR));
+ return 0;
+}
+EXPORT_SYMBOL(at91_set_pulldown);
+
+/*
+ * disable Schmitt trigger
+ */
+int __init_or_module at91_disable_schmitt_trig(unsigned pin)
+{
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
+
+ if (!pio || !has_pio3())
+ return -EINVAL;
+
+ __raw_writel(__raw_readl(pio + PIO_SCHMITT) | mask, pio + PIO_SCHMITT);
+ return 0;
+}
+EXPORT_SYMBOL(at91_disable_schmitt_trig);
+
+/*
* assuming the pin is muxed as a gpio output, set its value.
*/
int at91_set_gpio_value(unsigned pin, int value)
static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
{
- unsigned pin = irq_to_gpio(d->irq);
- unsigned mask = pin_to_mask(pin);
- unsigned bank = pin / 32;
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ unsigned mask = 1 << d->hwirq;
+ unsigned bank = at91_gpio->pioc_idx;
if (unlikely(bank >= MAX_GPIO_BANKS))
return -EINVAL;
else
wakeups[bank] &= ~mask;
- irq_set_irq_wake(gpio_chip[bank].id, state);
+ irq_set_irq_wake(at91_gpio->pioc_virq, state);
return 0;
}
__raw_writel(backups[i], pio + PIO_IDR);
__raw_writel(wakeups[i], pio + PIO_IER);
- if (!wakeups[i])
+ if (!wakeups[i]) {
+ clk_unprepare(gpio_chip[i].clock);
clk_disable(gpio_chip[i].clock);
- else {
+ } else {
#ifdef CONFIG_PM_DEBUG
printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]);
#endif
for (i = 0; i < gpio_banks; i++) {
void __iomem *pio = gpio_chip[i].regbase;
- if (!wakeups[i])
- clk_enable(gpio_chip[i].clock);
+ if (!wakeups[i]) {
+ if (clk_prepare(gpio_chip[i].clock) == 0)
+ clk_enable(gpio_chip[i].clock);
+ }
__raw_writel(wakeups[i], pio + PIO_IDR);
__raw_writel(backups[i], pio + PIO_IER);
* To use any AT91_PIN_* as an externally triggered IRQ, first call
* at91_set_gpio_input() then maybe enable its glitch filter.
* Then just request_irq() with the pin ID; it works like any ARM IRQ
- * handler, though it always triggers on rising and falling edges.
+ * handler.
+ * First implementation always triggers on rising and falling edges
+ * whereas the newer PIO3 can be additionally configured to trigger on
+ * level, edge with any polarity.
*
* Alternatively, certain pins may be used directly as IRQ0..IRQ6 after
* configuring them with at91_set_a_periph() or at91_set_b_periph().
static void gpio_irq_mask(struct irq_data *d)
{
- unsigned pin = irq_to_gpio(d->irq);
- void __iomem *pio = pin_to_controller(pin);
- unsigned mask = pin_to_mask(pin);
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << d->hwirq;
if (pio)
__raw_writel(mask, pio + PIO_IDR);
static void gpio_irq_unmask(struct irq_data *d)
{
- unsigned pin = irq_to_gpio(d->irq);
- void __iomem *pio = pin_to_controller(pin);
- unsigned mask = pin_to_mask(pin);
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << d->hwirq;
if (pio)
__raw_writel(mask, pio + PIO_IER);
}
}
+/* Alternate irq type for PIO3 support */
+static int alt_gpio_irq_type(struct irq_data *d, unsigned type)
+{
+ struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d);
+ void __iomem *pio = at91_gpio->regbase;
+ unsigned mask = 1 << d->hwirq;
+
+ switch (type) {
+ case IRQ_TYPE_EDGE_RISING:
+ __raw_writel(mask, pio + PIO_ESR);
+ __raw_writel(mask, pio + PIO_REHLSR);
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ __raw_writel(mask, pio + PIO_ESR);
+ __raw_writel(mask, pio + PIO_FELLSR);
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ __raw_writel(mask, pio + PIO_LSR);
+ __raw_writel(mask, pio + PIO_FELLSR);
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ __raw_writel(mask, pio + PIO_LSR);
+ __raw_writel(mask, pio + PIO_REHLSR);
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ /*
+ * disable additional interrupt modes:
+ * fall back to default behavior
+ */
+ __raw_writel(mask, pio + PIO_AIMDR);
+ return 0;
+ case IRQ_TYPE_NONE:
+ default:
+ pr_warn("AT91: No type for irq %d\n", gpio_to_irq(d->irq));
+ return -EINVAL;
+ }
+
+ /* enable additional interrupt modes */
+ __raw_writel(mask, pio + PIO_AIMER);
+
+ return 0;
+}
+
static struct irq_chip gpio_irqchip = {
.name = "GPIO",
.irq_disable = gpio_irq_mask,
.irq_mask = gpio_irq_mask,
.irq_unmask = gpio_irq_unmask,
- .irq_set_type = gpio_irq_type,
+ /* .irq_set_type is set dynamically */
.irq_set_wake = gpio_irq_set_wake,
};
static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
{
- unsigned irq_pin;
struct irq_data *idata = irq_desc_get_irq_data(desc);
struct irq_chip *chip = irq_data_get_irq_chip(idata);
struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata);
void __iomem *pio = at91_gpio->regbase;
- u32 isr;
+ unsigned long isr;
+ int n;
/* temporarily mask (level sensitive) parent IRQ */
chip->irq_ack(idata);
continue;
}
- irq_pin = gpio_to_irq(at91_gpio->chip.base);
-
- while (isr) {
- if (isr & 1)
- generic_handle_irq(irq_pin);
- irq_pin++;
- isr >>= 1;
+ n = find_first_bit(&isr, BITS_PER_LONG);
+ while (n < BITS_PER_LONG) {
+ generic_handle_irq(irq_find_mapping(at91_gpio->domain, n));
+ n = find_next_bit(&isr, BITS_PER_LONG, n + 1);
}
}
chip->irq_unmask(idata);
#ifdef CONFIG_DEBUG_FS
+static void gpio_printf(struct seq_file *s, void __iomem *pio, unsigned mask)
+{
+ char *trigger = NULL;
+ char *polarity = NULL;
+
+ if (__raw_readl(pio + PIO_IMR) & mask) {
+ if (!has_pio3() || !(__raw_readl(pio + PIO_AIMMR) & mask )) {
+ trigger = "edge";
+ polarity = "both";
+ } else {
+ if (__raw_readl(pio + PIO_ELSR) & mask) {
+ trigger = "level";
+ polarity = __raw_readl(pio + PIO_FRLHSR) & mask ?
+ "high" : "low";
+ } else {
+ trigger = "edge";
+ polarity = __raw_readl(pio + PIO_FRLHSR) & mask ?
+ "rising" : "falling";
+ }
+ }
+ seq_printf(s, "IRQ:%s-%s\t", trigger, polarity);
+ } else {
+ seq_printf(s, "GPIO:%s\t\t",
+ __raw_readl(pio + PIO_PDSR) & mask ? "1" : "0");
+ }
+}
+
static int at91_gpio_show(struct seq_file *s, void *unused)
{
int bank, j;
/* print heading */
seq_printf(s, "Pin\t");
for (bank = 0; bank < gpio_banks; bank++) {
- seq_printf(s, "PIO%c\t", 'A' + bank);
+ seq_printf(s, "PIO%c\t\t", 'A' + bank);
};
seq_printf(s, "\n\n");
unsigned mask = pin_to_mask(pin);
if (__raw_readl(pio + PIO_PSR) & mask)
- seq_printf(s, "GPIO:%s", __raw_readl(pio + PIO_PDSR) & mask ? "1" : "0");
+ gpio_printf(s, pio, mask);
else
- seq_printf(s, "%s", __raw_readl(pio + PIO_ABSR) & mask ? "B" : "A");
-
- seq_printf(s, "\t");
+ seq_printf(s, "%c\t\t",
+ peripheral_function(pio, mask));
}
seq_printf(s, "\n");
*/
static struct lock_class_key gpio_lock_class;
+#if defined(CONFIG_OF)
+static int at91_gpio_irq_map(struct irq_domain *h, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ struct at91_gpio_chip *at91_gpio = h->host_data;
+
+ irq_set_lockdep_class(virq, &gpio_lock_class);
+
+ /*
+ * Can use the "simple" and not "edge" handler since it's
+ * shorter, and the AIC handles interrupts sanely.
+ */
+ irq_set_chip_and_handler(virq, &gpio_irqchip,
+ handle_simple_irq);
+ set_irq_flags(virq, IRQF_VALID);
+ irq_set_chip_data(virq, at91_gpio);
+
+ return 0;
+}
+
+static struct irq_domain_ops at91_gpio_ops = {
+ .map = at91_gpio_irq_map,
+ .xlate = irq_domain_xlate_twocell,
+};
+
+int __init at91_gpio_of_irq_setup(struct device_node *node,
+ struct device_node *parent)
+{
+ struct at91_gpio_chip *prev = NULL;
+ int alias_idx = of_alias_get_id(node, "gpio");
+ struct at91_gpio_chip *at91_gpio = &gpio_chip[alias_idx];
+
+ /* Setup proper .irq_set_type function */
+ if (has_pio3())
+ gpio_irqchip.irq_set_type = alt_gpio_irq_type;
+ else
+ gpio_irqchip.irq_set_type = gpio_irq_type;
+
+ /* Disable irqs of this PIO controller */
+ __raw_writel(~0, at91_gpio->regbase + PIO_IDR);
+
+ /* Setup irq domain */
+ at91_gpio->domain = irq_domain_add_linear(node, at91_gpio->chip.ngpio,
+ &at91_gpio_ops, at91_gpio);
+ if (!at91_gpio->domain)
+ panic("at91_gpio.%d: couldn't allocate irq domain (DT).\n",
+ at91_gpio->pioc_idx);
+
+ /* Setup chained handler */
+ if (at91_gpio->pioc_idx)
+ prev = &gpio_chip[at91_gpio->pioc_idx - 1];
+
+ /* The toplevel handler handles one bank of GPIOs, except
+ * on some SoC it can handles up to three...
+ * We only set up the handler for the first of the list.
+ */
+ if (prev && prev->next == at91_gpio)
+ return 0;
+
+ at91_gpio->pioc_virq = irq_create_mapping(irq_find_host(parent),
+ at91_gpio->pioc_hwirq);
+ irq_set_chip_data(at91_gpio->pioc_virq, at91_gpio);
+ irq_set_chained_handler(at91_gpio->pioc_virq, gpio_irq_handler);
+
+ return 0;
+}
+#else
+int __init at91_gpio_of_irq_setup(struct device_node *node,
+ struct device_node *parent)
+{
+ return -EINVAL;
+}
+#endif
+
+/*
+ * irqdomain initialization: pile up irqdomains on top of AIC range
+ */
+static void __init at91_gpio_irqdomain(struct at91_gpio_chip *at91_gpio)
+{
+ int irq_base;
+
+ irq_base = irq_alloc_descs(-1, 0, at91_gpio->chip.ngpio, 0);
+ if (irq_base < 0)
+ panic("at91_gpio.%d: error %d: couldn't allocate IRQ numbers.\n",
+ at91_gpio->pioc_idx, irq_base);
+ at91_gpio->domain = irq_domain_add_legacy(NULL, at91_gpio->chip.ngpio,
+ irq_base, 0,
+ &irq_domain_simple_ops, NULL);
+ if (!at91_gpio->domain)
+ panic("at91_gpio.%d: couldn't allocate irq domain.\n",
+ at91_gpio->pioc_idx);
+}
+
/*
* Called from the processor-specific init to enable GPIO interrupt support.
*/
void __init at91_gpio_irq_setup(void)
{
- unsigned pioc, irq = gpio_to_irq(0);
+ unsigned pioc;
+ int gpio_irqnbr = 0;
struct at91_gpio_chip *this, *prev;
+ /* Setup proper .irq_set_type function */
+ if (has_pio3())
+ gpio_irqchip.irq_set_type = alt_gpio_irq_type;
+ else
+ gpio_irqchip.irq_set_type = gpio_irq_type;
+
for (pioc = 0, this = gpio_chip, prev = NULL;
pioc++ < gpio_banks;
prev = this, this++) {
- unsigned id = this->id;
- unsigned i;
+ int offset;
__raw_writel(~0, this->regbase + PIO_IDR);
- for (i = 0, irq = gpio_to_irq(this->chip.base); i < 32;
- i++, irq++) {
- irq_set_lockdep_class(irq, &gpio_lock_class);
+ /* setup irq domain for this GPIO controller */
+ at91_gpio_irqdomain(this);
+
+ for (offset = 0; offset < this->chip.ngpio; offset++) {
+ unsigned int virq = irq_find_mapping(this->domain, offset);
+ irq_set_lockdep_class(virq, &gpio_lock_class);
/*
* Can use the "simple" and not "edge" handler since it's
* shorter, and the AIC handles interrupts sanely.
*/
- irq_set_chip_and_handler(irq, &gpio_irqchip,
+ irq_set_chip_and_handler(virq, &gpio_irqchip,
handle_simple_irq);
- set_irq_flags(irq, IRQF_VALID);
+ set_irq_flags(virq, IRQF_VALID);
+ irq_set_chip_data(virq, this);
+
+ gpio_irqnbr++;
}
/* The toplevel handler handles one bank of GPIOs, except
- * AT91SAM9263_ID_PIOCDE handles three... PIOC is first in
- * the list, so we only set up that handler.
+ * on some SoC it can handles up to three...
+ * We only set up the handler for the first of the list.
*/
if (prev && prev->next == this)
continue;
- irq_set_chip_data(id, this);
- irq_set_chained_handler(id, gpio_irq_handler);
+ this->pioc_virq = irq_create_mapping(NULL, this->pioc_hwirq);
+ irq_set_chip_data(this->pioc_virq, this);
+ irq_set_chained_handler(this->pioc_virq, gpio_irq_handler);
}
- pr_info("AT91: %d gpio irqs in %d banks\n", irq - gpio_to_irq(0), gpio_banks);
+ pr_info("AT91: %d gpio irqs in %d banks\n", gpio_irqnbr, gpio_banks);
}
/* gpiolib support */
at91_get_gpio_value(pin) ?
"set" : "clear");
else
- seq_printf(s, "[periph %s]\n",
- __raw_readl(pio + PIO_ABSR) &
- mask ? "B" : "A");
+ seq_printf(s, "[periph %c]\n",
+ peripheral_function(pio, mask));
}
}
}
+static int at91_gpiolib_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
+ int virq;
+
+ if (offset < chip->ngpio)
+ virq = irq_create_mapping(at91_gpio->domain, offset);
+ else
+ virq = -ENXIO;
+
+ dev_dbg(chip->dev, "%s: request IRQ for GPIO %d, return %d\n",
+ chip->label, offset + chip->base, virq);
+ return virq;
+}
+
+static int __init at91_gpio_setup_clk(int idx)
+{
+ struct at91_gpio_chip *at91_gpio = &gpio_chip[idx];
+
+ /* retreive PIO controller's clock */
+ at91_gpio->clock = clk_get_sys(NULL, at91_gpio->chip.label);
+ if (IS_ERR(at91_gpio->clock)) {
+ pr_err("at91_gpio.%d, failed to get clock, ignoring.\n", idx);
+ goto err;
+ }
+
+ if (clk_prepare(at91_gpio->clock))
+ goto clk_prep_err;
+
+ /* enable PIO controller's clock */
+ if (clk_enable(at91_gpio->clock)) {
+ pr_err("at91_gpio.%d, failed to enable clock, ignoring.\n", idx);
+ goto clk_err;
+ }
+
+ return 0;
+
+clk_err:
+ clk_unprepare(at91_gpio->clock);
+clk_prep_err:
+ clk_put(at91_gpio->clock);
+err:
+ return -EINVAL;
+}
+
+#ifdef CONFIG_OF_GPIO
+static void __init of_at91_gpio_init_one(struct device_node *np)
+{
+ int alias_idx;
+ struct at91_gpio_chip *at91_gpio;
+
+ if (!np)
+ return;
+
+ alias_idx = of_alias_get_id(np, "gpio");
+ if (alias_idx >= MAX_GPIO_BANKS) {
+ pr_err("at91_gpio, failed alias idx(%d) > MAX_GPIO_BANKS(%d), ignoring.\n",
+ alias_idx, MAX_GPIO_BANKS);
+ return;
+ }
+
+ at91_gpio = &gpio_chip[alias_idx];
+ at91_gpio->chip.base = alias_idx * at91_gpio->chip.ngpio;
+
+ at91_gpio->regbase = of_iomap(np, 0);
+ if (!at91_gpio->regbase) {
+ pr_err("at91_gpio.%d, failed to map registers, ignoring.\n",
+ alias_idx);
+ return;
+ }
+
+ /* Get the interrupts property */
+ if (of_property_read_u32(np, "interrupts", &at91_gpio->pioc_hwirq)) {
+ pr_err("at91_gpio.%d, failed to get interrupts property, ignoring.\n",
+ alias_idx);
+ goto ioremap_err;
+ }
+
+ /* Get capabilities from compatibility property */
+ if (of_device_is_compatible(np, "atmel,at91sam9x5-gpio"))
+ at91_gpio_caps |= AT91_GPIO_CAP_PIO3;
+
+ /* Setup clock */
+ if (at91_gpio_setup_clk(alias_idx))
+ goto ioremap_err;
+
+ at91_gpio->chip.of_node = np;
+ gpio_banks = max(gpio_banks, alias_idx + 1);
+ at91_gpio->pioc_idx = alias_idx;
+ return;
+
+ioremap_err:
+ iounmap(at91_gpio->regbase);
+}
+
+static int __init of_at91_gpio_init(void)
+{
+ struct device_node *np = NULL;
+
+ /*
+ * This isn't ideal, but it gets things hooked up until this
+ * driver is converted into a platform_device
+ */
+ for_each_compatible_node(np, NULL, "atmel,at91rm9200-gpio")
+ of_at91_gpio_init_one(np);
+
+ return gpio_banks > 0 ? 0 : -EINVAL;
+}
+#else
+static int __init of_at91_gpio_init(void)
+{
+ return -EINVAL;
+}
+#endif
+
+static void __init at91_gpio_init_one(int idx, u32 regbase, int pioc_hwirq)
+{
+ struct at91_gpio_chip *at91_gpio = &gpio_chip[idx];
+
+ at91_gpio->chip.base = idx * at91_gpio->chip.ngpio;
+ at91_gpio->pioc_hwirq = pioc_hwirq;
+ at91_gpio->pioc_idx = idx;
+
+ at91_gpio->regbase = ioremap(regbase, 512);
+ if (!at91_gpio->regbase) {
+ pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", idx);
+ return;
+ }
+
+ if (at91_gpio_setup_clk(idx))
+ goto ioremap_err;
+
+ gpio_banks = max(gpio_banks, idx + 1);
+ return;
+
+ioremap_err:
+ iounmap(at91_gpio->regbase);
+}
+
/*
* Called from the processor-specific init to enable GPIO pin support.
*/
void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
{
- unsigned i;
+ unsigned i;
struct at91_gpio_chip *at91_gpio, *last = NULL;
BUG_ON(nr_banks > MAX_GPIO_BANKS);
- gpio_banks = nr_banks;
+ if (of_at91_gpio_init() < 0) {
+ /* No GPIO controller found in device tree */
+ for (i = 0; i < nr_banks; i++)
+ at91_gpio_init_one(i, data[i].regbase, data[i].id);
+ }
- for (i = 0; i < nr_banks; i++) {
+ for (i = 0; i < gpio_banks; i++) {
at91_gpio = &gpio_chip[i];
- at91_gpio->id = data[i].id;
- at91_gpio->chip.base = i * 32;
-
- at91_gpio->regbase = ioremap(data[i].regbase, 512);
- if (!at91_gpio->regbase) {
- pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", i);
- continue;
- }
-
- at91_gpio->clock = clk_get_sys(NULL, at91_gpio->chip.label);
- if (!at91_gpio->clock) {
- pr_err("at91_gpio.%d, failed to get clock, ignoring.\n", i);
- continue;
- }
-
- /* enable PIO controller's clock */
- clk_enable(at91_gpio->clock);
-
- /* AT91SAM9263_ID_PIOCDE groups PIOC, PIOD, PIOE */
- if (last && last->id == at91_gpio->id)
+ /*
+ * GPIO controller are grouped on some SoC:
+ * PIOC, PIOD and PIOE can share the same IRQ line
+ */
+ if (last && last->pioc_hwirq == at91_gpio->pioc_hwirq)
last->next = at91_gpio;
last = at91_gpio;
--- /dev/null
+/*
+ * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2
+ */
+
+#ifndef __MACH_AT91_MATRIX_H__
+#define __MACH_AT91_MATRIX_H__
+
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_matrix_base;
+
+#define at91_matrix_read(field) \
+ __raw_readl(at91_matrix_base + field)
+
+#define at91_matrix_write(field, value) \
+ __raw_writel(value, at91_matrix_base + field);
+
+#else
+.extern at91_matrix_base
+#endif
+
+#endif /* __MACH_AT91_MATRIX_H__ */
#define PIO_PUER 0x64 /* Pull-up Enable Register */
#define PIO_PUSR 0x68 /* Pull-up Status Register */
#define PIO_ASR 0x70 /* Peripheral A Select Register */
+#define PIO_ABCDSR1 0x70 /* Peripheral ABCD Select Register 1 [some sam9 only] */
#define PIO_BSR 0x74 /* Peripheral B Select Register */
+#define PIO_ABCDSR2 0x74 /* Peripheral ABCD Select Register 2 [some sam9 only] */
#define PIO_ABSR 0x78 /* AB Status Register */
+#define PIO_IFSCDR 0x80 /* Input Filter Slow Clock Disable Register */
+#define PIO_IFSCER 0x84 /* Input Filter Slow Clock Enable Register */
+#define PIO_IFSCSR 0x88 /* Input Filter Slow Clock Status Register */
+#define PIO_SCDR 0x8c /* Slow Clock Divider Debouncing Register */
+#define PIO_SCDR_DIV (0x3fff << 0) /* Slow Clock Divider Mask */
+#define PIO_PPDDR 0x90 /* Pad Pull-down Disable Register */
+#define PIO_PPDER 0x94 /* Pad Pull-down Enable Register */
+#define PIO_PPDSR 0x98 /* Pad Pull-down Status Register */
#define PIO_OWER 0xa0 /* Output Write Enable Register */
#define PIO_OWDR 0xa4 /* Output Write Disable Register */
#define PIO_OWSR 0xa8 /* Output Write Status Register */
+#define PIO_AIMER 0xb0 /* Additional Interrupt Modes Enable Register */
+#define PIO_AIMDR 0xb4 /* Additional Interrupt Modes Disable Register */
+#define PIO_AIMMR 0xb8 /* Additional Interrupt Modes Mask Register */
+#define PIO_ESR 0xc0 /* Edge Select Register */
+#define PIO_LSR 0xc4 /* Level Select Register */
+#define PIO_ELSR 0xc8 /* Edge/Level Status Register */
+#define PIO_FELLSR 0xd0 /* Falling Edge/Low Level Select Register */
+#define PIO_REHLSR 0xd4 /* Rising Edge/ High Level Select Register */
+#define PIO_FRLHSR 0xd8 /* Fall/Rise - Low/High Status Register */
+#define PIO_SCHMITT 0x100 /* Schmitt Trigger Register */
+
+#define ABCDSR_PERIPH_A 0x0
+#define ABCDSR_PERIPH_B 0x1
+#define ABCDSR_PERIPH_C 0x2
+#define ABCDSR_PERIPH_D 0x3
#endif
#ifndef AT91_PMC_H
#define AT91_PMC_H
-#define AT91_PMC_SCER (AT91_PMC + 0x00) /* System Clock Enable Register */
-#define AT91_PMC_SCDR (AT91_PMC + 0x04) /* System Clock Disable Register */
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_pmc_base;
-#define AT91_PMC_SCSR (AT91_PMC + 0x08) /* System Clock Status Register */
+#define at91_pmc_read(field) \
+ __raw_readl(at91_pmc_base + field)
+
+#define at91_pmc_write(field, value) \
+ __raw_writel(value, at91_pmc_base + field)
+#else
+.extern at91_aic_base
+#endif
+
+#define AT91_PMC_SCER 0x00 /* System Clock Enable Register */
+#define AT91_PMC_SCDR 0x04 /* System Clock Disable Register */
+
+#define AT91_PMC_SCSR 0x08 /* System Clock Status Register */
#define AT91_PMC_PCK (1 << 0) /* Processor Clock */
#define AT91RM9200_PMC_UDP (1 << 1) /* USB Devcice Port Clock [AT91RM9200 only] */
#define AT91RM9200_PMC_MCKUDP (1 << 2) /* USB Device Port Master Clock Automatic Disable on Suspend [AT91RM9200 only] */
#define AT91_PMC_HCK0 (1 << 16) /* AHB Clock (USB host) [AT91SAM9261 only] */
#define AT91_PMC_HCK1 (1 << 17) /* AHB Clock (LCD) [AT91SAM9261 only] */
-#define AT91_PMC_PCER (AT91_PMC + 0x10) /* Peripheral Clock Enable Register */
-#define AT91_PMC_PCDR (AT91_PMC + 0x14) /* Peripheral Clock Disable Register */
-#define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */
+#define AT91_PMC_PCER 0x10 /* Peripheral Clock Enable Register */
+#define AT91_PMC_PCDR 0x14 /* Peripheral Clock Disable Register */
+#define AT91_PMC_PCSR 0x18 /* Peripheral Clock Status Register */
-#define AT91_CKGR_UCKR (AT91_PMC + 0x1C) /* UTMI Clock Register [some SAM9] */
+#define AT91_CKGR_UCKR 0x1C /* UTMI Clock Register [some SAM9] */
#define AT91_PMC_UPLLEN (1 << 16) /* UTMI PLL Enable */
#define AT91_PMC_UPLLCOUNT (0xf << 20) /* UTMI PLL Start-up Time */
#define AT91_PMC_BIASEN (1 << 24) /* UTMI BIAS Enable */
#define AT91_PMC_BIASCOUNT (0xf << 28) /* UTMI BIAS Start-up Time */
-#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register [not on SAM9RL] */
+#define AT91_CKGR_MOR 0x20 /* Main Oscillator Register [not on SAM9RL] */
#define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */
#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass */
#define AT91_PMC_MOSCRCEN (1 << 3) /* Main On-Chip RC Oscillator Enable [some SAM9] */
#define AT91_PMC_MOSCSEL (1 << 24) /* Main Oscillator Selection [some SAM9] */
#define AT91_PMC_CFDEN (1 << 25) /* Clock Failure Detector Enable [some SAM9] */
-#define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */
+#define AT91_CKGR_MCFR 0x24 /* Main Clock Frequency Register */
#define AT91_PMC_MAINF (0xffff << 0) /* Main Clock Frequency */
#define AT91_PMC_MAINRDY (1 << 16) /* Main Clock Ready */
-#define AT91_CKGR_PLLAR (AT91_PMC + 0x28) /* PLL A Register */
-#define AT91_CKGR_PLLBR (AT91_PMC + 0x2c) /* PLL B Register */
+#define AT91_CKGR_PLLAR 0x28 /* PLL A Register */
+#define AT91_CKGR_PLLBR 0x2c /* PLL B Register */
#define AT91_PMC_DIV (0xff << 0) /* Divider */
#define AT91_PMC_PLLCOUNT (0x3f << 8) /* PLL Counter */
#define AT91_PMC_OUT (3 << 14) /* PLL Clock Frequency Range */
#define AT91_PMC_USBDIV_4 (2 << 28)
#define AT91_PMC_USB96M (1 << 28) /* Divider by 2 Enable (PLLB only) */
-#define AT91_PMC_MCKR (AT91_PMC + 0x30) /* Master Clock Register */
+#define AT91_PMC_MCKR 0x30 /* Master Clock Register */
#define AT91_PMC_CSS (3 << 0) /* Master Clock Selection */
#define AT91_PMC_CSS_SLOW (0 << 0)
#define AT91_PMC_CSS_MAIN (1 << 0)
#define AT91_PMC_PLLADIV2_OFF (0 << 12)
#define AT91_PMC_PLLADIV2_ON (1 << 12)
-#define AT91_PMC_USB (AT91_PMC + 0x38) /* USB Clock Register [some SAM9 only] */
+#define AT91_PMC_USB 0x38 /* USB Clock Register [some SAM9 only] */
#define AT91_PMC_USBS (0x1 << 0) /* USB OHCI Input clock selection */
#define AT91_PMC_USBS_PLLA (0 << 0)
#define AT91_PMC_USBS_UPLL (1 << 0)
#define AT91_PMC_OHCIUSBDIV (0xF << 8) /* Divider for USB OHCI Clock */
-#define AT91_PMC_SMD (AT91_PMC + 0x3c) /* Soft Modem Clock Register [some SAM9 only] */
+#define AT91_PMC_SMD 0x3c /* Soft Modem Clock Register [some SAM9 only] */
#define AT91_PMC_SMDS (0x1 << 0) /* SMD input clock selection */
#define AT91_PMC_SMD_DIV (0x1f << 8) /* SMD input clock divider */
#define AT91_PMC_SMDDIV(n) (((n) << 8) & AT91_PMC_SMD_DIV)
-#define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-N Registers */
+#define AT91_PMC_PCKR(n) (0x40 + ((n) * 4)) /* Programmable Clock 0-N Registers */
#define AT91_PMC_ALT_PCKR_CSS (0x7 << 0) /* Programmable Clock Source Selection [alternate length] */
#define AT91_PMC_CSS_MASTER (4 << 0) /* [some SAM9 only] */
#define AT91_PMC_CSSMCK (0x1 << 8) /* CSS or Master Clock Selection */
#define AT91_PMC_CSSMCK_CSS (0 << 8)
#define AT91_PMC_CSSMCK_MCK (1 << 8)
-#define AT91_PMC_IER (AT91_PMC + 0x60) /* Interrupt Enable Register */
-#define AT91_PMC_IDR (AT91_PMC + 0x64) /* Interrupt Disable Register */
-#define AT91_PMC_SR (AT91_PMC + 0x68) /* Status Register */
+#define AT91_PMC_IER 0x60 /* Interrupt Enable Register */
+#define AT91_PMC_IDR 0x64 /* Interrupt Disable Register */
+#define AT91_PMC_SR 0x68 /* Status Register */
#define AT91_PMC_MOSCS (1 << 0) /* MOSCS Flag */
#define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */
#define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */
#define AT91_PMC_MOSCSELS (1 << 16) /* Main Oscillator Selection [some SAM9] */
#define AT91_PMC_MOSCRCS (1 << 17) /* Main On-Chip RC [some SAM9] */
#define AT91_PMC_CFDEV (1 << 18) /* Clock Failure Detector Event [some SAM9] */
-#define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */
+#define AT91_PMC_IMR 0x6c /* Interrupt Mask Register */
-#define AT91_PMC_PROT (AT91_PMC + 0xe4) /* Write Protect Mode Register [some SAM9] */
+#define AT91_PMC_PROT 0xe4 /* Write Protect Mode Register [some SAM9] */
#define AT91_PMC_WPEN (0x1 << 0) /* Write Protect Enable */
#define AT91_PMC_WPKEY (0xffffff << 8) /* Write Protect Key */
#define AT91_PMC_PROTKEY (0x504d43 << 8) /* Activation Code */
-#define AT91_PMC_WPSR (AT91_PMC + 0xe8) /* Write Protect Status Register [some SAM9] */
+#define AT91_PMC_WPSR 0xe8 /* Write Protect Status Register [some SAM9] */
#define AT91_PMC_WPVS (0x1 << 0) /* Write Protect Violation Status */
#define AT91_PMC_WPVSRC (0xffff << 8) /* Write Protect Violation Source */
-#define AT91_PMC_PCR (AT91_PMC + 0x10c) /* Peripheral Control Register [some SAM9] */
+#define AT91_PMC_PCR 0x10c /* Peripheral Control Register [some SAM9] */
#define AT91_PMC_PCR_PID (0x3f << 0) /* Peripheral ID */
#define AT91_PMC_PCR_CMD (0x1 << 12) /* Command */
#define AT91_PMC_PCR_DIV (0x3 << 16) /* Divisor Value */
--- /dev/null
+/*
+ * Header file for the Atmel RAM Controller
+ *
+ * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2 only
+ */
+
+#ifndef __AT91_RAMC_H__
+#define __AT91_RAMC_H__
+
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_ramc_base[];
+
+#define at91_ramc_read(id, field) \
+ __raw_readl(at91_ramc_base[id] + field)
+
+#define at91_ramc_write(id, field, value) \
+ __raw_writel(value, at91_ramc_base[id] + field)
+#else
+.extern at91_ramc_base
+#endif
+
+#define AT91_MEMCTRL_MC 0
+#define AT91_MEMCTRL_SDRAMC 1
+#define AT91_MEMCTRL_DDRSDR 2
+
+#include <mach/at91rm9200_sdramc.h>
+#include <mach/at91sam9_ddrsdr.h>
+#include <mach/at91sam9_sdramc.h>
+
+#endif /* __AT91_RAMC_H__ */
#ifndef AT91_ST_H
#define AT91_ST_H
-#define AT91_ST_CR (AT91_ST + 0x00) /* Control Register */
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_st_base;
+
+#define at91_st_read(field) \
+ __raw_readl(at91_st_base + field)
+
+#define at91_st_write(field, value) \
+ __raw_writel(value, at91_st_base + field);
+#else
+.extern at91_st_base
+#endif
+
+#define AT91_ST_CR 0x00 /* Control Register */
#define AT91_ST_WDRST (1 << 0) /* Watchdog Timer Restart */
-#define AT91_ST_PIMR (AT91_ST + 0x04) /* Period Interval Mode Register */
+#define AT91_ST_PIMR 0x04 /* Period Interval Mode Register */
#define AT91_ST_PIV (0xffff << 0) /* Period Interval Value */
-#define AT91_ST_WDMR (AT91_ST + 0x08) /* Watchdog Mode Register */
+#define AT91_ST_WDMR 0x08 /* Watchdog Mode Register */
#define AT91_ST_WDV (0xffff << 0) /* Watchdog Counter Value */
#define AT91_ST_RSTEN (1 << 16) /* Reset Enable */
#define AT91_ST_EXTEN (1 << 17) /* External Signal Assertion Enable */
-#define AT91_ST_RTMR (AT91_ST + 0x0c) /* Real-time Mode Register */
+#define AT91_ST_RTMR 0x0c /* Real-time Mode Register */
#define AT91_ST_RTPRES (0xffff << 0) /* Real-time Prescalar Value */
-#define AT91_ST_SR (AT91_ST + 0x10) /* Status Register */
+#define AT91_ST_SR 0x10 /* Status Register */
#define AT91_ST_PITS (1 << 0) /* Period Interval Timer Status */
#define AT91_ST_WDOVF (1 << 1) /* Watchdog Overflow */
#define AT91_ST_RTTINC (1 << 2) /* Real-time Timer Increment */
#define AT91_ST_ALMS (1 << 3) /* Alarm Status */
-#define AT91_ST_IER (AT91_ST + 0x14) /* Interrupt Enable Register */
-#define AT91_ST_IDR (AT91_ST + 0x18) /* Interrupt Disable Register */
-#define AT91_ST_IMR (AT91_ST + 0x1c) /* Interrupt Mask Register */
+#define AT91_ST_IER 0x14 /* Interrupt Enable Register */
+#define AT91_ST_IDR 0x18 /* Interrupt Disable Register */
+#define AT91_ST_IMR 0x1c /* Interrupt Mask Register */
-#define AT91_ST_RTAR (AT91_ST + 0x20) /* Real-time Alarm Register */
+#define AT91_ST_RTAR 0x20 /* Real-time Alarm Register */
#define AT91_ST_ALMV (0xfffff << 0) /* Alarm Value */
-#define AT91_ST_CRTR (AT91_ST + 0x24) /* Current Real-time Register */
+#define AT91_ST_CRTR 0x24 /* Current Real-time Register */
#define AT91_ST_CRTV (0xfffff << 0) /* Current Real-Time Value */
#endif
/*
- * System Peripherals (offset from AT91_BASE_SYS)
+ * System Peripherals
*/
-#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) /* Power Management Controller */
-#define AT91_ST (0xfffffd00 - AT91_BASE_SYS) /* System Timer */
-#define AT91_MC (0xffffff00 - AT91_BASE_SYS) /* Memory Controllers */
-
#define AT91RM9200_BASE_DBGU AT91_BASE_DBGU0 /* Debug Unit */
#define AT91RM9200_BASE_PIOA 0xfffff400 /* PIO Controller A */
#define AT91RM9200_BASE_PIOB 0xfffff600 /* PIO Controller B */
#define AT91RM9200_BASE_PIOC 0xfffff800 /* PIO Controller C */
#define AT91RM9200_BASE_PIOD 0xfffffa00 /* PIO Controller D */
+#define AT91RM9200_BASE_ST 0xfffffd00 /* System Timer */
#define AT91RM9200_BASE_RTC 0xfffffe00 /* Real-Time Clock */
+#define AT91RM9200_BASE_MC 0xffffff00 /* Memory Controllers */
#define AT91_USART0 AT91RM9200_BASE_US0
#define AT91_USART1 AT91RM9200_BASE_US1
#define AT91_USART2 AT91RM9200_BASE_US2
#define AT91_USART3 AT91RM9200_BASE_US3
-#define AT91_MATRIX 0 /* not supported */
-
/*
* Internal Memory.
*/
#define AT91RM9200_MC_H
/* Memory Controller */
-#define AT91_MC_RCR (AT91_MC + 0x00) /* MC Remap Control Register */
+#define AT91_MC_RCR 0x00 /* MC Remap Control Register */
#define AT91_MC_RCB (1 << 0) /* Remap Command Bit */
-#define AT91_MC_ASR (AT91_MC + 0x04) /* MC Abort Status Register */
+#define AT91_MC_ASR 0x04 /* MC Abort Status Register */
#define AT91_MC_UNADD (1 << 0) /* Undefined Address Abort Status */
#define AT91_MC_MISADD (1 << 1) /* Misaligned Address Abort Status */
#define AT91_MC_ABTSZ (3 << 8) /* Abort Size Status */
#define AT91_MC_SVMST2 (1 << 26) /* Saved UHP Abort Source */
#define AT91_MC_SVMST3 (1 << 27) /* Saved EMAC Abort Source */
-#define AT91_MC_AASR (AT91_MC + 0x08) /* MC Abort Address Status Register */
+#define AT91_MC_AASR 0x08 /* MC Abort Address Status Register */
-#define AT91_MC_MPR (AT91_MC + 0x0c) /* MC Master Priority Register */
+#define AT91_MC_MPR 0x0c /* MC Master Priority Register */
#define AT91_MPR_MSTP0 (7 << 0) /* ARM920T Priority */
#define AT91_MPR_MSTP1 (7 << 4) /* PDC Priority */
#define AT91_MPR_MSTP2 (7 << 8) /* UHP Priority */
#define AT91_MPR_MSTP3 (7 << 12) /* EMAC Priority */
/* External Bus Interface (EBI) registers */
-#define AT91_EBI_CSA (AT91_MC + 0x60) /* Chip Select Assignment Register */
+#define AT91_EBI_CSA 0x60 /* Chip Select Assignment Register */
#define AT91_EBI_CS0A (1 << 0) /* Chip Select 0 Assignment */
#define AT91_EBI_CS0A_SMC (0 << 0)
#define AT91_EBI_CS0A_BFC (1 << 0)
#define AT91_EBI_DBPUC (1 << 0) /* Data Bus Pull-Up Configuration */
/* Static Memory Controller (SMC) registers */
-#define AT91_SMC_CSR(n) (AT91_MC + 0x70 + ((n) * 4))/* SMC Chip Select Register */
+#define AT91_SMC_CSR(n) (0x70 + ((n) * 4)) /* SMC Chip Select Register */
#define AT91_SMC_NWS (0x7f << 0) /* Number of Wait States */
#define AT91_SMC_NWS_(x) ((x) << 0)
#define AT91_SMC_WSEN (1 << 7) /* Wait State Enable */
#define AT91_SMC_RWHOLD (7 << 28) /* Read & Write Signal Hold Time */
#define AT91_SMC_RWHOLD_(x) ((x) << 28)
-/* SDRAM Controller registers */
-#define AT91_SDRAMC_MR (AT91_MC + 0x90) /* Mode Register */
-#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */
-#define AT91_SDRAMC_MODE_NORMAL (0 << 0)
-#define AT91_SDRAMC_MODE_NOP (1 << 0)
-#define AT91_SDRAMC_MODE_PRECHARGE (2 << 0)
-#define AT91_SDRAMC_MODE_LMR (3 << 0)
-#define AT91_SDRAMC_MODE_REFRESH (4 << 0)
-#define AT91_SDRAMC_DBW (1 << 4) /* Data Bus Width */
-#define AT91_SDRAMC_DBW_32 (0 << 4)
-#define AT91_SDRAMC_DBW_16 (1 << 4)
-
-#define AT91_SDRAMC_TR (AT91_MC + 0x94) /* Refresh Timer Register */
-#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
-
-#define AT91_SDRAMC_CR (AT91_MC + 0x98) /* Configuration Register */
-#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */
-#define AT91_SDRAMC_NC_8 (0 << 0)
-#define AT91_SDRAMC_NC_9 (1 << 0)
-#define AT91_SDRAMC_NC_10 (2 << 0)
-#define AT91_SDRAMC_NC_11 (3 << 0)
-#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */
-#define AT91_SDRAMC_NR_11 (0 << 2)
-#define AT91_SDRAMC_NR_12 (1 << 2)
-#define AT91_SDRAMC_NR_13 (2 << 2)
-#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */
-#define AT91_SDRAMC_NB_2 (0 << 4)
-#define AT91_SDRAMC_NB_4 (1 << 4)
-#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */
-#define AT91_SDRAMC_CAS_2 (2 << 5)
-#define AT91_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */
-#define AT91_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */
-#define AT91_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */
-#define AT91_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */
-#define AT91_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
-#define AT91_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
-
-#define AT91_SDRAMC_SRR (AT91_MC + 0x9c) /* Self Refresh Register */
-#define AT91_SDRAMC_LPR (AT91_MC + 0xa0) /* Low Power Register */
-#define AT91_SDRAMC_IER (AT91_MC + 0xa4) /* Interrupt Enable Register */
-#define AT91_SDRAMC_IDR (AT91_MC + 0xa8) /* Interrupt Disable Register */
-#define AT91_SDRAMC_IMR (AT91_MC + 0xac) /* Interrupt Mask Register */
-#define AT91_SDRAMC_ISR (AT91_MC + 0xb0) /* Interrupt Status Register */
-
/* Burst Flash Controller register */
-#define AT91_BFC_MR (AT91_MC + 0xc0) /* Mode Register */
+#define AT91_BFC_MR 0xc0 /* Mode Register */
#define AT91_BFC_BFCOM (3 << 0) /* Burst Flash Controller Operating Mode */
#define AT91_BFC_BFCOM_DISABLED (0 << 0)
#define AT91_BFC_BFCOM_ASYNC (1 << 0)
--- /dev/null
+/*
+ * arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Memory Controllers (SDRAMC only) - System peripherals registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91RM9200_SDRAMC_H
+#define AT91RM9200_SDRAMC_H
+
+/* SDRAM Controller registers */
+#define AT91RM9200_SDRAMC_MR 0x90 /* Mode Register */
+#define AT91RM9200_SDRAMC_MODE (0xf << 0) /* Command Mode */
+#define AT91RM9200_SDRAMC_MODE_NORMAL (0 << 0)
+#define AT91RM9200_SDRAMC_MODE_NOP (1 << 0)
+#define AT91RM9200_SDRAMC_MODE_PRECHARGE (2 << 0)
+#define AT91RM9200_SDRAMC_MODE_LMR (3 << 0)
+#define AT91RM9200_SDRAMC_MODE_REFRESH (4 << 0)
+#define AT91RM9200_SDRAMC_DBW (1 << 4) /* Data Bus Width */
+#define AT91RM9200_SDRAMC_DBW_32 (0 << 4)
+#define AT91RM9200_SDRAMC_DBW_16 (1 << 4)
+
+#define AT91RM9200_SDRAMC_TR 0x94 /* Refresh Timer Register */
+#define AT91RM9200_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
+
+#define AT91RM9200_SDRAMC_CR 0x98 /* Configuration Register */
+#define AT91RM9200_SDRAMC_NC (3 << 0) /* Number of Column Bits */
+#define AT91RM9200_SDRAMC_NC_8 (0 << 0)
+#define AT91RM9200_SDRAMC_NC_9 (1 << 0)
+#define AT91RM9200_SDRAMC_NC_10 (2 << 0)
+#define AT91RM9200_SDRAMC_NC_11 (3 << 0)
+#define AT91RM9200_SDRAMC_NR (3 << 2) /* Number of Row Bits */
+#define AT91RM9200_SDRAMC_NR_11 (0 << 2)
+#define AT91RM9200_SDRAMC_NR_12 (1 << 2)
+#define AT91RM9200_SDRAMC_NR_13 (2 << 2)
+#define AT91RM9200_SDRAMC_NB (1 << 4) /* Number of Banks */
+#define AT91RM9200_SDRAMC_NB_2 (0 << 4)
+#define AT91RM9200_SDRAMC_NB_4 (1 << 4)
+#define AT91RM9200_SDRAMC_CAS (3 << 5) /* CAS Latency */
+#define AT91RM9200_SDRAMC_CAS_2 (2 << 5)
+#define AT91RM9200_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */
+#define AT91RM9200_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */
+#define AT91RM9200_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */
+#define AT91RM9200_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */
+#define AT91RM9200_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
+#define AT91RM9200_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
+
+#define AT91RM9200_SDRAMC_SRR 0x9c /* Self Refresh Register */
+#define AT91RM9200_SDRAMC_LPR 0xa0 /* Low Power Register */
+#define AT91RM9200_SDRAMC_IER 0xa4 /* Interrupt Enable Register */
+#define AT91RM9200_SDRAMC_IDR 0xa8 /* Interrupt Disable Register */
+#define AT91RM9200_SDRAMC_IMR 0xac /* Interrupt Mask Register */
+#define AT91RM9200_SDRAMC_ISR 0xb0 /* Interrupt Status Register */
+
+#endif
#define AT91SAM9260_BASE_ADC 0xfffe0000
/*
- * System Peripherals (offset from AT91_BASE_SYS)
+ * System Peripherals
*/
-#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
-#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
-#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
-#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
-
#define AT91SAM9260_BASE_ECC 0xffffe800
+#define AT91SAM9260_BASE_SDRAMC 0xffffea00
#define AT91SAM9260_BASE_SMC 0xffffec00
+#define AT91SAM9260_BASE_MATRIX 0xffffee00
#define AT91SAM9260_BASE_DBGU AT91_BASE_DBGU0
#define AT91SAM9260_BASE_PIOA 0xfffff400
#define AT91SAM9260_BASE_PIOB 0xfffff600
#define AT91SAM9260_BASE_RTT 0xfffffd20
#define AT91SAM9260_BASE_PIT 0xfffffd30
#define AT91SAM9260_BASE_WDT 0xfffffd40
+#define AT91SAM9260_BASE_GPBR 0xfffffd50
#define AT91_USART0 AT91SAM9260_BASE_US0
#define AT91_USART1 AT91SAM9260_BASE_US1
#define AT91SAM9260_SRAM0_SIZE SZ_4K /* Internal SRAM 0 size (4Kb) */
#define AT91SAM9260_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */
#define AT91SAM9260_SRAM1_SIZE SZ_4K /* Internal SRAM 1 size (4Kb) */
+#define AT91SAM9260_SRAM_BASE 0x002FF000 /* Internal SRAM base address */
+#define AT91SAM9260_SRAM_SIZE SZ_8K /* Internal SRAM size (8Kb) */
#define AT91SAM9260_UHP_BASE 0x00500000 /* USB Host controller */
#define AT91SAM9G20_SRAM0_SIZE SZ_16K /* Internal SRAM 0 size (16Kb) */
#define AT91SAM9G20_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */
#define AT91SAM9G20_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */
+#define AT91SAM9G20_SRAM_BASE 0x002FC000 /* Internal SRAM base address */
+#define AT91SAM9G20_SRAM_SIZE SZ_32K /* Internal SRAM size (32Kb) */
#define AT91SAM9G20_UHP_BASE 0x00500000 /* USB Host controller */
#ifndef AT91SAM9260_MATRIX_H
#define AT91SAM9260_MATRIX_H
-#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x14) /* Master Configuration Register 5 */
+#define AT91_MATRIX_MCFG0 0x00 /* Master Configuration Register 0 */
+#define AT91_MATRIX_MCFG1 0x04 /* Master Configuration Register 1 */
+#define AT91_MATRIX_MCFG2 0x08 /* Master Configuration Register 2 */
+#define AT91_MATRIX_MCFG3 0x0C /* Master Configuration Register 3 */
+#define AT91_MATRIX_MCFG4 0x10 /* Master Configuration Register 4 */
+#define AT91_MATRIX_MCFG5 0x14 /* Master Configuration Register 5 */
#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */
#define AT91_MATRIX_ULBT_INFINITE (0 << 0)
#define AT91_MATRIX_ULBT_SINGLE (1 << 0)
#define AT91_MATRIX_ULBT_EIGHT (3 << 0)
#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0)
-#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */
+#define AT91_MATRIX_SCFG0 0x40 /* Slave Configuration Register 0 */
+#define AT91_MATRIX_SCFG1 0x44 /* Slave Configuration Register 1 */
+#define AT91_MATRIX_SCFG2 0x48 /* Slave Configuration Register 2 */
+#define AT91_MATRIX_SCFG3 0x4C /* Slave Configuration Register 3 */
+#define AT91_MATRIX_SCFG4 0x50 /* Slave Configuration Register 4 */
#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */
#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */
#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16)
#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24)
#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24)
-#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */
+#define AT91_MATRIX_PRAS0 0x80 /* Priority Register A for Slave 0 */
+#define AT91_MATRIX_PRAS1 0x88 /* Priority Register A for Slave 1 */
+#define AT91_MATRIX_PRAS2 0x90 /* Priority Register A for Slave 2 */
+#define AT91_MATRIX_PRAS3 0x98 /* Priority Register A for Slave 3 */
+#define AT91_MATRIX_PRAS4 0xA0 /* Priority Register A for Slave 4 */
#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */
#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */
#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */
#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */
#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */
-#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */
+#define AT91_MATRIX_MRCR 0x100 /* Master Remap Control Register */
#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x11C) /* EBI Chip Select Assignment Register */
+#define AT91_MATRIX_EBICSA 0x11C /* EBI Chip Select Assignment Register */
#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_MATRIX_CS1A_SMC (0 << 1)
#define AT91_MATRIX_CS1A_SDRAMC (1 << 1)
/*
- * System Peripherals (offset from AT91_BASE_SYS)
+ * System Peripherals
*/
-#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
-#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
-#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
-#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
-
#define AT91SAM9261_BASE_SMC 0xffffec00
+#define AT91SAM9261_BASE_MATRIX 0xffffee00
+#define AT91SAM9261_BASE_SDRAMC 0xffffea00
#define AT91SAM9261_BASE_DBGU AT91_BASE_DBGU0
#define AT91SAM9261_BASE_PIOA 0xfffff400
#define AT91SAM9261_BASE_PIOB 0xfffff600
#define AT91SAM9261_BASE_RTT 0xfffffd20
#define AT91SAM9261_BASE_PIT 0xfffffd30
#define AT91SAM9261_BASE_WDT 0xfffffd40
+#define AT91SAM9261_BASE_GPBR 0xfffffd50
#define AT91_USART0 AT91SAM9261_BASE_US0
#define AT91_USART1 AT91SAM9261_BASE_US1
#ifndef AT91SAM9261_MATRIX_H
#define AT91SAM9261_MATRIX_H
-#define AT91_MATRIX_MCFG (AT91_MATRIX + 0x00) /* Master Configuration Register */
+#define AT91_MATRIX_MCFG 0x00 /* Master Configuration Register */
#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x04) /* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x08) /* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x0C) /* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x10) /* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x14) /* Slave Configuration Register 4 */
+#define AT91_MATRIX_SCFG0 0x04 /* Slave Configuration Register 0 */
+#define AT91_MATRIX_SCFG1 0x08 /* Slave Configuration Register 1 */
+#define AT91_MATRIX_SCFG2 0x0C /* Slave Configuration Register 2 */
+#define AT91_MATRIX_SCFG3 0x10 /* Slave Configuration Register 3 */
+#define AT91_MATRIX_SCFG4 0x14 /* Slave Configuration Register 4 */
#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */
#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */
#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16)
#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16)
#define AT91_MATRIX_FIXED_DEFMSTR (7 << 18) /* Fixed Index of Default Master */
-#define AT91_MATRIX_TCR (AT91_MATRIX + 0x24) /* TCM Configuration Register */
+#define AT91_MATRIX_TCR 0x24 /* TCM Configuration Register */
#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */
#define AT91_MATRIX_ITCM_0 (0 << 0)
#define AT91_MATRIX_ITCM_16 (5 << 0)
#define AT91_MATRIX_DTCM_32 (6 << 4)
#define AT91_MATRIX_DTCM_64 (7 << 4)
-#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x30) /* EBI Chip Select Assignment Register */
+#define AT91_MATRIX_EBICSA 0x30 /* EBI Chip Select Assignment Register */
#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_MATRIX_CS1A_SMC (0 << 1)
#define AT91_MATRIX_CS1A_SDRAMC (1 << 1)
#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5)
#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */
-#define AT91_MATRIX_USBPUCR (AT91_MATRIX + 0x34) /* USB Pad Pull-Up Control Register */
+#define AT91_MATRIX_USBPUCR 0x34 /* USB Pad Pull-Up Control Register */
#define AT91_MATRIX_USBPUCR_PUON (1 << 30) /* USB Device PAD Pull-up Enable */
#endif
#define AT91SAM9263_BASE_2DGE 0xfffc8000
/*
- * System Peripherals (offset from AT91_BASE_SYS)
+ * System Peripherals
*/
-#define AT91_SDRAMC0 (0xffffe200 - AT91_BASE_SYS)
-#define AT91_SDRAMC1 (0xffffe800 - AT91_BASE_SYS)
-#define AT91_MATRIX (0xffffec00 - AT91_BASE_SYS)
-#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
-#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
-
#define AT91SAM9263_BASE_ECC0 0xffffe000
+#define AT91SAM9263_BASE_SDRAMC0 0xffffe200
#define AT91SAM9263_BASE_SMC0 0xffffe400
#define AT91SAM9263_BASE_ECC1 0xffffe600
+#define AT91SAM9263_BASE_SDRAMC1 0xffffe800
#define AT91SAM9263_BASE_SMC1 0xffffea00
+#define AT91SAM9263_BASE_MATRIX 0xffffec00
#define AT91SAM9263_BASE_DBGU AT91_BASE_DBGU1
#define AT91SAM9263_BASE_PIOA 0xfffff200
#define AT91SAM9263_BASE_PIOB 0xfffff400
#define AT91SAM9263_BASE_PIT 0xfffffd30
#define AT91SAM9263_BASE_WDT 0xfffffd40
#define AT91SAM9263_BASE_RTT1 0xfffffd50
+#define AT91SAM9263_BASE_GPBR 0xfffffd60
#define AT91_USART0 AT91SAM9263_BASE_US0
#define AT91_USART1 AT91SAM9263_BASE_US1
#ifndef AT91SAM9263_MATRIX_H
#define AT91SAM9263_MATRIX_H
-#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x14) /* Master Configuration Register 5 */
-#define AT91_MATRIX_MCFG6 (AT91_MATRIX + 0x18) /* Master Configuration Register 6 */
-#define AT91_MATRIX_MCFG7 (AT91_MATRIX + 0x1C) /* Master Configuration Register 7 */
-#define AT91_MATRIX_MCFG8 (AT91_MATRIX + 0x20) /* Master Configuration Register 8 */
+#define AT91_MATRIX_MCFG0 0x00 /* Master Configuration Register 0 */
+#define AT91_MATRIX_MCFG1 0x04 /* Master Configuration Register 1 */
+#define AT91_MATRIX_MCFG2 0x08 /* Master Configuration Register 2 */
+#define AT91_MATRIX_MCFG3 0x0C /* Master Configuration Register 3 */
+#define AT91_MATRIX_MCFG4 0x10 /* Master Configuration Register 4 */
+#define AT91_MATRIX_MCFG5 0x14 /* Master Configuration Register 5 */
+#define AT91_MATRIX_MCFG6 0x18 /* Master Configuration Register 6 */
+#define AT91_MATRIX_MCFG7 0x1C /* Master Configuration Register 7 */
+#define AT91_MATRIX_MCFG8 0x20 /* Master Configuration Register 8 */
#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */
#define AT91_MATRIX_ULBT_INFINITE (0 << 0)
#define AT91_MATRIX_ULBT_SINGLE (1 << 0)
#define AT91_MATRIX_ULBT_EIGHT (3 << 0)
#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0)
-#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */
-#define AT91_MATRIX_SCFG5 (AT91_MATRIX + 0x54) /* Slave Configuration Register 5 */
-#define AT91_MATRIX_SCFG6 (AT91_MATRIX + 0x58) /* Slave Configuration Register 6 */
-#define AT91_MATRIX_SCFG7 (AT91_MATRIX + 0x5C) /* Slave Configuration Register 7 */
+#define AT91_MATRIX_SCFG0 0x40 /* Slave Configuration Register 0 */
+#define AT91_MATRIX_SCFG1 0x44 /* Slave Configuration Register 1 */
+#define AT91_MATRIX_SCFG2 0x48 /* Slave Configuration Register 2 */
+#define AT91_MATRIX_SCFG3 0x4C /* Slave Configuration Register 3 */
+#define AT91_MATRIX_SCFG4 0x50 /* Slave Configuration Register 4 */
+#define AT91_MATRIX_SCFG5 0x54 /* Slave Configuration Register 5 */
+#define AT91_MATRIX_SCFG6 0x58 /* Slave Configuration Register 6 */
+#define AT91_MATRIX_SCFG7 0x5C /* Slave Configuration Register 7 */
#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */
#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */
#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16)
#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24)
#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24)
-#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRBS0 (AT91_MATRIX + 0x84) /* Priority Register B for Slave 0 */
-#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRBS1 (AT91_MATRIX + 0x8C) /* Priority Register B for Slave 1 */
-#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRBS2 (AT91_MATRIX + 0x94) /* Priority Register B for Slave 2 */
-#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRBS3 (AT91_MATRIX + 0x9C) /* Priority Register B for Slave 3 */
-#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */
-#define AT91_MATRIX_PRBS4 (AT91_MATRIX + 0xA4) /* Priority Register B for Slave 4 */
-#define AT91_MATRIX_PRAS5 (AT91_MATRIX + 0xA8) /* Priority Register A for Slave 5 */
-#define AT91_MATRIX_PRBS5 (AT91_MATRIX + 0xAC) /* Priority Register B for Slave 5 */
-#define AT91_MATRIX_PRAS6 (AT91_MATRIX + 0xB0) /* Priority Register A for Slave 6 */
-#define AT91_MATRIX_PRBS6 (AT91_MATRIX + 0xB4) /* Priority Register B for Slave 6 */
-#define AT91_MATRIX_PRAS7 (AT91_MATRIX + 0xB8) /* Priority Register A for Slave 7 */
-#define AT91_MATRIX_PRBS7 (AT91_MATRIX + 0xBC) /* Priority Register B for Slave 7 */
+#define AT91_MATRIX_PRAS0 0x80 /* Priority Register A for Slave 0 */
+#define AT91_MATRIX_PRBS0 0x84 /* Priority Register B for Slave 0 */
+#define AT91_MATRIX_PRAS1 0x88 /* Priority Register A for Slave 1 */
+#define AT91_MATRIX_PRBS1 0x8C /* Priority Register B for Slave 1 */
+#define AT91_MATRIX_PRAS2 0x90 /* Priority Register A for Slave 2 */
+#define AT91_MATRIX_PRBS2 0x94 /* Priority Register B for Slave 2 */
+#define AT91_MATRIX_PRAS3 0x98 /* Priority Register A for Slave 3 */
+#define AT91_MATRIX_PRBS3 0x9C /* Priority Register B for Slave 3 */
+#define AT91_MATRIX_PRAS4 0xA0 /* Priority Register A for Slave 4 */
+#define AT91_MATRIX_PRBS4 0xA4 /* Priority Register B for Slave 4 */
+#define AT91_MATRIX_PRAS5 0xA8 /* Priority Register A for Slave 5 */
+#define AT91_MATRIX_PRBS5 0xAC /* Priority Register B for Slave 5 */
+#define AT91_MATRIX_PRAS6 0xB0 /* Priority Register A for Slave 6 */
+#define AT91_MATRIX_PRBS6 0xB4 /* Priority Register B for Slave 6 */
+#define AT91_MATRIX_PRAS7 0xB8 /* Priority Register A for Slave 7 */
+#define AT91_MATRIX_PRBS7 0xBC /* Priority Register B for Slave 7 */
#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */
#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */
#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */
#define AT91_MATRIX_M7PR (3 << 28) /* Master 7 Priority */
#define AT91_MATRIX_M8PR (3 << 0) /* Master 8 Priority (in Register B) */
-#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */
+#define AT91_MATRIX_MRCR 0x100 /* Master Remap Control Register */
#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
#define AT91_MATRIX_RCB2 (1 << 2)
#define AT91_MATRIX_RCB7 (1 << 7)
#define AT91_MATRIX_RCB8 (1 << 8)
-#define AT91_MATRIX_TCMR (AT91_MATRIX + 0x114) /* TCM Configuration Register */
+#define AT91_MATRIX_TCMR 0x114 /* TCM Configuration Register */
#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */
#define AT91_MATRIX_ITCM_0 (0 << 0)
#define AT91_MATRIX_ITCM_16 (5 << 0)
#define AT91_MATRIX_DTCM_16 (5 << 4)
#define AT91_MATRIX_DTCM_32 (6 << 4)
-#define AT91_MATRIX_EBI0CSA (AT91_MATRIX + 0x120) /* EBI0 Chip Select Assignment Register */
+#define AT91_MATRIX_EBI0CSA 0x120 /* EBI0 Chip Select Assignment Register */
#define AT91_MATRIX_EBI0_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_MATRIX_EBI0_CS1A_SMC (0 << 1)
#define AT91_MATRIX_EBI0_CS1A_SDRAMC (1 << 1)
#define AT91_MATRIX_EBI0_VDDIOMSEL_1_8V (0 << 16)
#define AT91_MATRIX_EBI0_VDDIOMSEL_3_3V (1 << 16)
-#define AT91_MATRIX_EBI1CSA (AT91_MATRIX + 0x124) /* EBI1 Chip Select Assignment Register */
+#define AT91_MATRIX_EBI1CSA 0x124 /* EBI1 Chip Select Assignment Register */
#define AT91_MATRIX_EBI1_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_MATRIX_EBI1_CS1A_SMC (0 << 1)
#define AT91_MATRIX_EBI1_CS1A_SDRAMC (1 << 1)
#define AT91_DDRSDRC_WPVS (1 << 0) /* Write protect violation status */
#define AT91_DDRSDRC_WPVSRC (0xffff << 8) /* Write protect violation source */
-/* Register access macros */
-#define at91_ramc_read(num, reg) \
- at91_sys_read(AT91_DDRSDRC##num + reg)
-#define at91_ramc_write(num, reg, value) \
- at91_sys_write(AT91_DDRSDRC##num + reg, value)
-
#endif
#define AT91_SDRAMC_MD_SDRAM 0
#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1
-/* Register access macros */
-#define at91_ramc_read(num, reg) \
- at91_sys_read(AT91_SDRAMC##num + reg)
-#define at91_ramc_write(num, reg, value) \
- at91_sys_write(AT91_SDRAMC##num + reg, value)
-
#endif
#define AT91SAM9G45_BASE_TC5 0xfffd4080
/*
- * System Peripherals (offset from AT91_BASE_SYS)
+ * System Peripherals
*/
-#define AT91_DDRSDRC1 (0xffffe400 - AT91_BASE_SYS)
-#define AT91_DDRSDRC0 (0xffffe600 - AT91_BASE_SYS)
-#define AT91_MATRIX (0xffffea00 - AT91_BASE_SYS)
-#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
-#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
-
#define AT91SAM9G45_BASE_ECC 0xffffe200
+#define AT91SAM9G45_BASE_DDRSDRC1 0xffffe400
+#define AT91SAM9G45_BASE_DDRSDRC0 0xffffe600
#define AT91SAM9G45_BASE_DMA 0xffffec00
#define AT91SAM9G45_BASE_SMC 0xffffe800
+#define AT91SAM9G45_BASE_MATRIX 0xffffea00
#define AT91SAM9G45_BASE_DBGU AT91_BASE_DBGU1
#define AT91SAM9G45_BASE_PIOA 0xfffff200
#define AT91SAM9G45_BASE_PIOB 0xfffff400
#define AT91SAM9G45_BASE_PIT 0xfffffd30
#define AT91SAM9G45_BASE_WDT 0xfffffd40
#define AT91SAM9G45_BASE_RTC 0xfffffdb0
+#define AT91SAM9G45_BASE_GPBR 0xfffffd60
#define AT91_USART0 AT91SAM9G45_BASE_US0
#define AT91_USART1 AT91SAM9G45_BASE_US1
#ifndef AT91SAM9G45_MATRIX_H
#define AT91SAM9G45_MATRIX_H
-#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x14) /* Master Configuration Register 5 */
-#define AT91_MATRIX_MCFG6 (AT91_MATRIX + 0x18) /* Master Configuration Register 6 */
-#define AT91_MATRIX_MCFG7 (AT91_MATRIX + 0x1C) /* Master Configuration Register 7 */
-#define AT91_MATRIX_MCFG8 (AT91_MATRIX + 0x20) /* Master Configuration Register 8 */
-#define AT91_MATRIX_MCFG9 (AT91_MATRIX + 0x24) /* Master Configuration Register 9 */
-#define AT91_MATRIX_MCFG10 (AT91_MATRIX + 0x28) /* Master Configuration Register 10 */
-#define AT91_MATRIX_MCFG11 (AT91_MATRIX + 0x2C) /* Master Configuration Register 11 */
+#define AT91_MATRIX_MCFG0 0x00 /* Master Configuration Register 0 */
+#define AT91_MATRIX_MCFG1 0x04 /* Master Configuration Register 1 */
+#define AT91_MATRIX_MCFG2 0x08 /* Master Configuration Register 2 */
+#define AT91_MATRIX_MCFG3 0x0C /* Master Configuration Register 3 */
+#define AT91_MATRIX_MCFG4 0x10 /* Master Configuration Register 4 */
+#define AT91_MATRIX_MCFG5 0x14 /* Master Configuration Register 5 */
+#define AT91_MATRIX_MCFG6 0x18 /* Master Configuration Register 6 */
+#define AT91_MATRIX_MCFG7 0x1C /* Master Configuration Register 7 */
+#define AT91_MATRIX_MCFG8 0x20 /* Master Configuration Register 8 */
+#define AT91_MATRIX_MCFG9 0x24 /* Master Configuration Register 9 */
+#define AT91_MATRIX_MCFG10 0x28 /* Master Configuration Register 10 */
+#define AT91_MATRIX_MCFG11 0x2C /* Master Configuration Register 11 */
#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */
#define AT91_MATRIX_ULBT_INFINITE (0 << 0)
#define AT91_MATRIX_ULBT_SINGLE (1 << 0)
#define AT91_MATRIX_ULBT_SIXTYFOUR (6 << 0)
#define AT91_MATRIX_ULBT_128 (7 << 0)
-#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */
-#define AT91_MATRIX_SCFG5 (AT91_MATRIX + 0x54) /* Slave Configuration Register 5 */
-#define AT91_MATRIX_SCFG6 (AT91_MATRIX + 0x58) /* Slave Configuration Register 6 */
-#define AT91_MATRIX_SCFG7 (AT91_MATRIX + 0x5C) /* Slave Configuration Register 7 */
+#define AT91_MATRIX_SCFG0 0x40 /* Slave Configuration Register 0 */
+#define AT91_MATRIX_SCFG1 0x44 /* Slave Configuration Register 1 */
+#define AT91_MATRIX_SCFG2 0x48 /* Slave Configuration Register 2 */
+#define AT91_MATRIX_SCFG3 0x4C /* Slave Configuration Register 3 */
+#define AT91_MATRIX_SCFG4 0x50 /* Slave Configuration Register 4 */
+#define AT91_MATRIX_SCFG5 0x54 /* Slave Configuration Register 5 */
+#define AT91_MATRIX_SCFG6 0x58 /* Slave Configuration Register 6 */
+#define AT91_MATRIX_SCFG7 0x5C /* Slave Configuration Register 7 */
#define AT91_MATRIX_SLOT_CYCLE (0x1ff << 0) /* Maximum Number of Allowed Cycles for a Burst */
#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */
#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16)
#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16)
#define AT91_MATRIX_FIXED_DEFMSTR (0xf << 18) /* Fixed Index of Default Master */
-#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRBS0 (AT91_MATRIX + 0x84) /* Priority Register B for Slave 0 */
-#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRBS1 (AT91_MATRIX + 0x8C) /* Priority Register B for Slave 1 */
-#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRBS2 (AT91_MATRIX + 0x94) /* Priority Register B for Slave 2 */
-#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRBS3 (AT91_MATRIX + 0x9C) /* Priority Register B for Slave 3 */
-#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */
-#define AT91_MATRIX_PRBS4 (AT91_MATRIX + 0xA4) /* Priority Register B for Slave 4 */
-#define AT91_MATRIX_PRAS5 (AT91_MATRIX + 0xA8) /* Priority Register A for Slave 5 */
-#define AT91_MATRIX_PRBS5 (AT91_MATRIX + 0xAC) /* Priority Register B for Slave 5 */
-#define AT91_MATRIX_PRAS6 (AT91_MATRIX + 0xB0) /* Priority Register A for Slave 6 */
-#define AT91_MATRIX_PRBS6 (AT91_MATRIX + 0xB4) /* Priority Register B for Slave 6 */
-#define AT91_MATRIX_PRAS7 (AT91_MATRIX + 0xB8) /* Priority Register A for Slave 7 */
-#define AT91_MATRIX_PRBS7 (AT91_MATRIX + 0xBC) /* Priority Register B for Slave 7 */
+#define AT91_MATRIX_PRAS0 0x80 /* Priority Register A for Slave 0 */
+#define AT91_MATRIX_PRBS0 0x84 /* Priority Register B for Slave 0 */
+#define AT91_MATRIX_PRAS1 0x88 /* Priority Register A for Slave 1 */
+#define AT91_MATRIX_PRBS1 0x8C /* Priority Register B for Slave 1 */
+#define AT91_MATRIX_PRAS2 0x90 /* Priority Register A for Slave 2 */
+#define AT91_MATRIX_PRBS2 0x94 /* Priority Register B for Slave 2 */
+#define AT91_MATRIX_PRAS3 0x98 /* Priority Register A for Slave 3 */
+#define AT91_MATRIX_PRBS3 0x9C /* Priority Register B for Slave 3 */
+#define AT91_MATRIX_PRAS4 0xA0 /* Priority Register A for Slave 4 */
+#define AT91_MATRIX_PRBS4 0xA4 /* Priority Register B for Slave 4 */
+#define AT91_MATRIX_PRAS5 0xA8 /* Priority Register A for Slave 5 */
+#define AT91_MATRIX_PRBS5 0xAC /* Priority Register B for Slave 5 */
+#define AT91_MATRIX_PRAS6 0xB0 /* Priority Register A for Slave 6 */
+#define AT91_MATRIX_PRBS6 0xB4 /* Priority Register B for Slave 6 */
+#define AT91_MATRIX_PRAS7 0xB8 /* Priority Register A for Slave 7 */
+#define AT91_MATRIX_PRBS7 0xBC /* Priority Register B for Slave 7 */
#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */
#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */
#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */
#define AT91_MATRIX_M10PR (3 << 8) /* Master 10 Priority (in Register B) */
#define AT91_MATRIX_M11PR (3 << 12) /* Master 11 Priority (in Register B) */
-#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */
+#define AT91_MATRIX_MRCR 0x100 /* Master Remap Control Register */
#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
#define AT91_MATRIX_RCB2 (1 << 2)
#define AT91_MATRIX_RCB10 (1 << 10)
#define AT91_MATRIX_RCB11 (1 << 11)
-#define AT91_MATRIX_TCMR (AT91_MATRIX + 0x110) /* TCM Configuration Register */
+#define AT91_MATRIX_TCMR 0x110 /* TCM Configuration Register */
#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */
#define AT91_MATRIX_ITCM_0 (0 << 0)
#define AT91_MATRIX_ITCM_32 (6 << 0)
#define AT91_MATRIX_TCM_NO_WS (0x0 << 11)
#define AT91_MATRIX_TCM_ONE_WS (0x1 << 11)
-#define AT91_MATRIX_VIDEO (AT91_MATRIX + 0x118) /* Video Mode Configuration Register */
+#define AT91_MATRIX_VIDEO 0x118 /* Video Mode Configuration Register */
#define AT91C_VDEC_SEL (0x1 << 0) /* Video Mode Selection */
#define AT91C_VDEC_SEL_OFF (0 << 0)
#define AT91C_VDEC_SEL_ON (1 << 0)
-#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x128) /* EBI Chip Select Assignment Register */
+#define AT91_MATRIX_EBICSA 0x128 /* EBI Chip Select Assignment Register */
#define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_MATRIX_EBI_CS1A_SMC (0 << 1)
#define AT91_MATRIX_EBI_CS1A_SDRAMC (1 << 1)
#define AT91_MATRIX_EBI_DDR_IOSR_REDUCED (0 << 18)
#define AT91_MATRIX_EBI_DDR_IOSR_NORMAL (1 << 18)
-#define AT91_MATRIX_WPMR (AT91_MATRIX + 0x1E4) /* Write Protect Mode Register */
+#define AT91_MATRIX_WPMR 0x1E4 /* Write Protect Mode Register */
#define AT91_MATRIX_WPMR_WPEN (1 << 0) /* Write Protect ENable */
#define AT91_MATRIX_WPMR_WP_WPDIS (0 << 0)
#define AT91_MATRIX_WPMR_WP_WPEN (1 << 0)
#define AT91_MATRIX_WPMR_WPKEY (0xFFFFFF << 8) /* Write Protect KEY */
-#define AT91_MATRIX_WPSR (AT91_MATRIX + 0x1E8) /* Write Protect Status Register */
+#define AT91_MATRIX_WPSR 0x1E8 /* Write Protect Status Register */
#define AT91_MATRIX_WPSR_WPVS (1 << 0) /* Write Protect Violation Status */
#define AT91_MATRIX_WPSR_NO_WPV (0 << 0)
#define AT91_MATRIX_WPSR_WPV (1 << 0)
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
-#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
-#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
-#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_SCKCR (0xfffffd50 - AT91_BASE_SYS)
-#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
#define AT91SAM9RL_BASE_DMA 0xffffe600
#define AT91SAM9RL_BASE_ECC 0xffffe800
+#define AT91SAM9RL_BASE_SDRAMC 0xffffea00
#define AT91SAM9RL_BASE_SMC 0xffffec00
+#define AT91SAM9RL_BASE_MATRIX 0xffffee00
#define AT91SAM9RL_BASE_DBGU AT91_BASE_DBGU0
#define AT91SAM9RL_BASE_PIOA 0xfffff400
#define AT91SAM9RL_BASE_PIOB 0xfffff600
#define AT91SAM9RL_BASE_RTT 0xfffffd20
#define AT91SAM9RL_BASE_PIT 0xfffffd30
#define AT91SAM9RL_BASE_WDT 0xfffffd40
+#define AT91SAM9RL_BASE_GPBR 0xfffffd60
#define AT91SAM9RL_BASE_RTC 0xfffffe00
#define AT91_USART0 AT91SAM9RL_BASE_US0
#ifndef AT91SAM9RL_MATRIX_H
#define AT91SAM9RL_MATRIX_H
-#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x14) /* Master Configuration Register 5 */
+#define AT91_MATRIX_MCFG0 0x00 /* Master Configuration Register 0 */
+#define AT91_MATRIX_MCFG1 0x04 /* Master Configuration Register 1 */
+#define AT91_MATRIX_MCFG2 0x08 /* Master Configuration Register 2 */
+#define AT91_MATRIX_MCFG3 0x0C /* Master Configuration Register 3 */
+#define AT91_MATRIX_MCFG4 0x10 /* Master Configuration Register 4 */
+#define AT91_MATRIX_MCFG5 0x14 /* Master Configuration Register 5 */
#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */
#define AT91_MATRIX_ULBT_INFINITE (0 << 0)
#define AT91_MATRIX_ULBT_SINGLE (1 << 0)
#define AT91_MATRIX_ULBT_EIGHT (3 << 0)
#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0)
-#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */
-#define AT91_MATRIX_SCFG5 (AT91_MATRIX + 0x54) /* Slave Configuration Register 5 */
+#define AT91_MATRIX_SCFG0 0x40 /* Slave Configuration Register 0 */
+#define AT91_MATRIX_SCFG1 0x44 /* Slave Configuration Register 1 */
+#define AT91_MATRIX_SCFG2 0x48 /* Slave Configuration Register 2 */
+#define AT91_MATRIX_SCFG3 0x4C /* Slave Configuration Register 3 */
+#define AT91_MATRIX_SCFG4 0x50 /* Slave Configuration Register 4 */
+#define AT91_MATRIX_SCFG5 0x54 /* Slave Configuration Register 5 */
#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */
#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */
#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16)
#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24)
#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24)
-#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */
-#define AT91_MATRIX_PRAS5 (AT91_MATRIX + 0xA8) /* Priority Register A for Slave 5 */
+#define AT91_MATRIX_PRAS0 0x80 /* Priority Register A for Slave 0 */
+#define AT91_MATRIX_PRAS1 0x88 /* Priority Register A for Slave 1 */
+#define AT91_MATRIX_PRAS2 0x90 /* Priority Register A for Slave 2 */
+#define AT91_MATRIX_PRAS3 0x98 /* Priority Register A for Slave 3 */
+#define AT91_MATRIX_PRAS4 0xA0 /* Priority Register A for Slave 4 */
+#define AT91_MATRIX_PRAS5 0xA8 /* Priority Register A for Slave 5 */
#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */
#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */
#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */
#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */
#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */
-#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */
+#define AT91_MATRIX_MRCR 0x100 /* Master Remap Control Register */
#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
#define AT91_MATRIX_RCB2 (1 << 2)
#define AT91_MATRIX_RCB4 (1 << 4)
#define AT91_MATRIX_RCB5 (1 << 5)
-#define AT91_MATRIX_TCMR (AT91_MATRIX + 0x114) /* TCM Configuration Register */
+#define AT91_MATRIX_TCMR 0x114 /* TCM Configuration Register */
#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */
#define AT91_MATRIX_ITCM_0 (0 << 0)
#define AT91_MATRIX_ITCM_16 (5 << 0)
#define AT91_MATRIX_DTCM_16 (5 << 4)
#define AT91_MATRIX_DTCM_32 (6 << 4)
-#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x120) /* EBI0 Chip Select Assignment Register */
+#define AT91_MATRIX_EBICSA 0x120 /* EBI0 Chip Select Assignment Register */
#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_MATRIX_CS1A_SMC (0 << 1)
#define AT91_MATRIX_CS1A_SDRAMC (1 << 1)
#define AT91SAM9X5_BASE_USART2 0xf8024000
/*
- * System Peripherals (offset from AT91_BASE_SYS)
+ * System Peripherals
*/
-#define AT91_DDRSDRC0 (0xffffe800 - AT91_BASE_SYS)
-#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
+#define AT91SAM9X5_BASE_DDRSDRC0 0xffffe800
/*
* Base addresses for early serial code (uncompress.h)
#define AT91X40_ID_IRQ2 18 /* External IRQ 2 */
/*
- * System Peripherals (offset from AT91_BASE_SYS)
+ * System Peripherals
*/
#define AT91_BASE_SYS 0xffc00000
-#define AT91_EBI (0xffe00000 - AT91_BASE_SYS) /* External Bus Interface */
-#define AT91_SF (0xfff00000 - AT91_BASE_SYS) /* Special Function */
-#define AT91_USART1 (0xfffcc000 - AT91_BASE_SYS) /* USART 1 */
-#define AT91_USART0 (0xfffd0000 - AT91_BASE_SYS) /* USART 0 */
-#define AT91_TC (0xfffe0000 - AT91_BASE_SYS) /* Timer Counter */
-#define AT91_PIOA (0xffff0000 - AT91_BASE_SYS) /* PIO Controller A */
-#define AT91_PS (0xffff4000 - AT91_BASE_SYS) /* Power Save */
-#define AT91_WD (0xffff8000 - AT91_BASE_SYS) /* Watchdog Timer */
+#define AT91_EBI 0xffe00000 /* External Bus Interface */
+#define AT91_SF 0xfff00000 /* Special Function */
+#define AT91_USART1 0xfffcc000 /* USART 1 */
+#define AT91_USART0 0xfffd0000 /* USART 0 */
+#define AT91_TC 0xfffe0000 /* Timer Counter */
+#define AT91_PIOA 0xffff0000 /* PIO Controller A */
+#define AT91_PS 0xffff4000 /* Power Save */
+#define AT91_WD 0xffff8000 /* Watchdog Timer */
/*
* The AT91x40 series doesn't have a debug unit like the other AT91 parts.
extern int __init_or_module at91_set_GPIO_periph(unsigned pin, int use_pullup);
extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup);
extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup);
+extern int __init_or_module at91_set_C_periph(unsigned pin, int use_pullup);
+extern int __init_or_module at91_set_D_periph(unsigned pin, int use_pullup);
extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup);
extern int __init_or_module at91_set_gpio_output(unsigned pin, int value);
extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on);
+extern int __init_or_module at91_set_debounce(unsigned pin, int is_on, int div);
extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on);
+extern int __init_or_module at91_set_pulldown(unsigned pin, int is_on);
+extern int __init_or_module at91_disable_schmitt_trig(unsigned pin);
/* callable at any time */
extern int at91_set_gpio_value(unsigned pin, int value);
extern void at91_gpio_suspend(void);
extern void at91_gpio_resume(void);
-/*-------------------------------------------------------------------------*/
-
-/* wrappers for "new style" GPIO calls. the old AT91-specific ones should
- * eventually be removed (along with this errno.h inclusion), and the
- * gpio request/free calls should probably be implemented.
- */
-
-#include <asm/errno.h>
-
-#define gpio_to_irq(gpio) (gpio + NR_AIC_IRQS)
-#define irq_to_gpio(irq) (irq - NR_AIC_IRQS)
-
#endif /* __ASSEMBLY__ */
#endif
/*
* On all at91 have the Advanced Interrupt Controller starts at address
- * 0xfffff000
+ * 0xfffff000 and the Power Management Controller starts at 0xfffffc00
*/
#define AT91_AIC 0xfffff000
+#define AT91_PMC 0xfffffc00
/*
* Peripheral identifiers/interrupts.
#define __io(a) __typesafe_io(a)
#define __mem_pci(a) (a)
-#ifndef __ASSEMBLY__
-
-static inline unsigned int at91_sys_read(unsigned int reg_offset)
-{
- void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS;
-
- return __raw_readl(addr + reg_offset);
-}
-
-static inline void at91_sys_write(unsigned int reg_offset, unsigned long value)
-{
- void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS;
-
- __raw_writel(value, addr + reg_offset);
-}
-
-#endif
-
#endif
#include <linux/module.h>
#include <linux/mm.h>
#include <linux/types.h>
+#include <linux/irq.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/irqdomain.h>
+#include <linux/err.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
void __iomem *at91_aic_base;
+static struct irq_domain *at91_aic_domain;
+static struct device_node *at91_aic_np;
static void at91_aic_mask_irq(struct irq_data *d)
{
/* Disable interrupt on AIC */
- at91_aic_write(AT91_AIC_IDCR, 1 << d->irq);
+ at91_aic_write(AT91_AIC_IDCR, 1 << d->hwirq);
}
static void at91_aic_unmask_irq(struct irq_data *d)
{
/* Enable interrupt on AIC */
- at91_aic_write(AT91_AIC_IECR, 1 << d->irq);
+ at91_aic_write(AT91_AIC_IECR, 1 << d->hwirq);
}
unsigned int at91_extern_irq;
-#define is_extern_irq(irq) ((1 << (irq)) & at91_extern_irq)
+#define is_extern_irq(hwirq) ((1 << (hwirq)) & at91_extern_irq)
static int at91_aic_set_type(struct irq_data *d, unsigned type)
{
srctype = AT91_AIC_SRCTYPE_RISING;
break;
case IRQ_TYPE_LEVEL_LOW:
- if ((d->irq == AT91_ID_FIQ) || is_extern_irq(d->irq)) /* only supported on external interrupts */
+ if ((d->hwirq == AT91_ID_FIQ) || is_extern_irq(d->hwirq)) /* only supported on external interrupts */
srctype = AT91_AIC_SRCTYPE_LOW;
else
return -EINVAL;
break;
case IRQ_TYPE_EDGE_FALLING:
- if ((d->irq == AT91_ID_FIQ) || is_extern_irq(d->irq)) /* only supported on external interrupts */
+ if ((d->hwirq == AT91_ID_FIQ) || is_extern_irq(d->hwirq)) /* only supported on external interrupts */
srctype = AT91_AIC_SRCTYPE_FALLING;
else
return -EINVAL;
return -EINVAL;
}
- smr = at91_aic_read(AT91_AIC_SMR(d->irq)) & ~AT91_AIC_SRCTYPE;
- at91_aic_write(AT91_AIC_SMR(d->irq), smr | srctype);
+ smr = at91_aic_read(AT91_AIC_SMR(d->hwirq)) & ~AT91_AIC_SRCTYPE;
+ at91_aic_write(AT91_AIC_SMR(d->hwirq), smr | srctype);
return 0;
}
static int at91_aic_set_wake(struct irq_data *d, unsigned value)
{
- if (unlikely(d->irq >= 32))
+ if (unlikely(d->hwirq >= NR_AIC_IRQS))
return -EINVAL;
if (value)
- wakeups |= (1 << d->irq);
+ wakeups |= (1 << d->hwirq);
else
- wakeups &= ~(1 << d->irq);
+ wakeups &= ~(1 << d->hwirq);
return 0;
}
.irq_set_wake = at91_aic_set_wake,
};
+static void __init at91_aic_hw_init(unsigned int spu_vector)
+{
+ int i;
+
+ /*
+ * Perform 8 End Of Interrupt Command to make sure AIC
+ * will not Lock out nIRQ
+ */
+ for (i = 0; i < 8; i++)
+ at91_aic_write(AT91_AIC_EOICR, 0);
+
+ /*
+ * Spurious Interrupt ID in Spurious Vector Register.
+ * When there is no current interrupt, the IRQ Vector Register
+ * reads the value stored in AIC_SPU
+ */
+ at91_aic_write(AT91_AIC_SPU, spu_vector);
+
+ /* No debugging in AIC: Debug (Protect) Control Register */
+ at91_aic_write(AT91_AIC_DCR, 0);
+
+ /* Disable and clear all interrupts initially */
+ at91_aic_write(AT91_AIC_IDCR, 0xFFFFFFFF);
+ at91_aic_write(AT91_AIC_ICCR, 0xFFFFFFFF);
+}
+
+#if defined(CONFIG_OF)
+static int at91_aic_irq_map(struct irq_domain *h, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ /* Put virq number in Source Vector Register */
+ at91_aic_write(AT91_AIC_SVR(hw), virq);
+
+ /* Active Low interrupt, without priority */
+ at91_aic_write(AT91_AIC_SMR(hw), AT91_AIC_SRCTYPE_LOW);
+
+ irq_set_chip_and_handler(virq, &at91_aic_chip, handle_level_irq);
+ set_irq_flags(virq, IRQF_VALID | IRQF_PROBE);
+
+ return 0;
+}
+
+static struct irq_domain_ops at91_aic_irq_ops = {
+ .map = at91_aic_irq_map,
+ .xlate = irq_domain_xlate_twocell,
+};
+
+int __init at91_aic_of_init(struct device_node *node,
+ struct device_node *parent)
+{
+ at91_aic_base = of_iomap(node, 0);
+ at91_aic_np = node;
+
+ at91_aic_domain = irq_domain_add_linear(at91_aic_np, NR_AIC_IRQS,
+ &at91_aic_irq_ops, NULL);
+ if (!at91_aic_domain)
+ panic("Unable to add AIC irq domain (DT)\n");
+
+ irq_set_default_host(at91_aic_domain);
+
+ at91_aic_hw_init(NR_AIC_IRQS);
+
+ return 0;
+}
+#endif
+
/*
* Initialize the AIC interrupt controller.
*/
void __init at91_aic_init(unsigned int priority[NR_AIC_IRQS])
{
unsigned int i;
+ int irq_base;
at91_aic_base = ioremap(AT91_AIC, 512);
-
if (!at91_aic_base)
- panic("Impossible to ioremap AT91_AIC\n");
+ panic("Unable to ioremap AIC registers\n");
+
+ /* Add irq domain for AIC */
+ irq_base = irq_alloc_descs(-1, 0, NR_AIC_IRQS, 0);
+ if (irq_base < 0) {
+ WARN(1, "Cannot allocate irq_descs, assuming pre-allocated\n");
+ irq_base = 0;
+ }
+ at91_aic_domain = irq_domain_add_legacy(at91_aic_np, NR_AIC_IRQS,
+ irq_base, 0,
+ &irq_domain_simple_ops, NULL);
+
+ if (!at91_aic_domain)
+ panic("Unable to add AIC irq domain\n");
+
+ irq_set_default_host(at91_aic_domain);
/*
* The IVR is used by macro get_irqnr_and_base to read and verify.
* The irq number is NR_AIC_IRQS when a spurious interrupt has occurred.
*/
for (i = 0; i < NR_AIC_IRQS; i++) {
- /* Put irq number in Source Vector Register: */
+ /* Put hardware irq number in Source Vector Register: */
at91_aic_write(AT91_AIC_SVR(i), i);
/* Active Low interrupt, with the specified priority */
at91_aic_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]);
irq_set_chip_and_handler(i, &at91_aic_chip, handle_level_irq);
set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
-
- /* Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ */
- if (i < 8)
- at91_aic_write(AT91_AIC_EOICR, 0);
}
- /*
- * Spurious Interrupt ID in Spurious Vector Register is NR_AIC_IRQS
- * When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU
- */
- at91_aic_write(AT91_AIC_SPU, NR_AIC_IRQS);
-
- /* No debugging in AIC: Debug (Protect) Control Register */
- at91_aic_write(AT91_AIC_DCR, 0);
-
- /* Disable and clear all interrupts initially */
- at91_aic_write(AT91_AIC_IDCR, 0xFFFFFFFF);
- at91_aic_write(AT91_AIC_ICCR, 0xFFFFFFFF);
+ at91_aic_hw_init(NR_AIC_IRQS);
}
unsigned long scsr;
int i;
- scsr = at91_sys_read(AT91_PMC_SCSR);
+ scsr = at91_pmc_read(AT91_PMC_SCSR);
/* USB must not be using PLLB */
if (cpu_is_at91rm9200()) {
if ((scsr & (AT91_PMC_PCK0 << i)) == 0)
continue;
- css = at91_sys_read(AT91_PMC_PCKR(i)) & AT91_PMC_CSS;
+ css = at91_pmc_read(AT91_PMC_PCKR(i)) & AT91_PMC_CSS;
if (css != AT91_PMC_CSS_SLOW) {
pr_err("AT91: PM - Suspend-to-RAM with PCK%d src %d\n", i, css);
return 0;
EXPORT_SYMBOL(at91_suspend_entering_slow_clock);
-static void (*slow_clock)(void);
+static void (*slow_clock)(void __iomem *pmc, void __iomem *ramc0,
+ void __iomem *ramc1, int memctrl);
#ifdef CONFIG_AT91_SLOW_CLOCK
-extern void at91_slow_clock(void);
+extern void at91_slow_clock(void __iomem *pmc, void __iomem *ramc0,
+ void __iomem *ramc1, int memctrl);
extern u32 at91_slow_clock_sz;
#endif
+void __iomem *at91_ramc_base[2];
+
+void __init at91_ioremap_ramc(int id, u32 addr, u32 size)
+{
+ if (id < 0 || id > 1) {
+ pr_emerg("Wrong RAM controller id (%d), cannot continue\n", id);
+ BUG();
+ }
+ at91_ramc_base[id] = ioremap(addr, size);
+ if (!at91_ramc_base[id])
+ panic("Impossible to ioremap ramc.%d 0x%x\n", id, addr);
+}
static int at91_pm_enter(suspend_state_t state)
{
pr_debug("AT91: PM - wake mask %08x, pm state %d\n",
/* remember all the always-wake irqs */
- (at91_sys_read(AT91_PMC_PCSR)
+ (at91_pmc_read(AT91_PMC_PCSR)
| (1 << AT91_ID_FIQ)
| (1 << AT91_ID_SYS)
| (at91_extern_irq))
* turning off the main oscillator; reverse on wakeup.
*/
if (slow_clock) {
+ int memctrl = AT91_MEMCTRL_SDRAMC;
+
+ if (cpu_is_at91rm9200())
+ memctrl = AT91_MEMCTRL_MC;
+ else if (cpu_is_at91sam9g45())
+ memctrl = AT91_MEMCTRL_DDRSDR;
#ifdef CONFIG_AT91_SLOW_CLOCK
/* copy slow_clock handler to SRAM, and call it */
memcpy(slow_clock, at91_slow_clock, at91_slow_clock_sz);
#endif
- slow_clock();
+ slow_clock(at91_pmc_base, at91_ramc_base[0],
+ at91_ramc_base[1], memctrl);
break;
} else {
pr_info("AT91: PM - no slow clock mode enabled ...\n");
#ifdef CONFIG_ARCH_AT91RM9200
/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
- at91_sys_write(AT91_SDRAMC_LPR, 0);
+ at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
#endif
suspend_set_ops(&at91_pm_ops);
#ifndef __ARCH_ARM_MACH_AT91_PM
#define __ARCH_ARM_MACH_AT91_PM
+#include <mach/at91_ramc.h>
#ifdef CONFIG_ARCH_AT91RM9200
-#include <mach/at91rm9200_mc.h>
+#include <mach/at91rm9200_sdramc.h>
/*
* The AT91RM9200 goes into self-refresh mode with this command, and will
static inline void at91rm9200_standby(void)
{
- u32 lpr = at91_sys_read(AT91_SDRAMC_LPR);
+ u32 lpr = at91_ramc_read(0, AT91RM9200_SDRAMC_LPR);
asm volatile(
"b 1f\n\t"
" mcr p15, 0, %0, c7, c0, 4\n\t"
" str %5, [%1, %2]"
:
- : "r" (0), "r" (AT91_BASE_SYS), "r" (AT91_SDRAMC_LPR),
- "r" (1), "r" (AT91_SDRAMC_SRR),
+ : "r" (0), "r" (AT91_BASE_SYS), "r" (AT91RM9200_SDRAMC_LPR),
+ "r" (1), "r" (AT91RM9200_SDRAMC_SRR),
"r" (lpr));
}
#define at91_standby at91rm9200_standby
#elif defined(CONFIG_ARCH_AT91SAM9G45)
-#include <mach/at91sam9_ddrsdr.h>
/* We manage both DDRAM/SDRAM controllers, we need more than one value to
* remember.
#define at91_standby at91sam9g45_standby
#else
-#include <mach/at91sam9_sdramc.h>
#ifdef CONFIG_ARCH_AT91SAM9263
/*
#include <linux/linkage.h>
#include <mach/hardware.h>
#include <mach/at91_pmc.h>
-
-#if defined(CONFIG_ARCH_AT91RM9200)
-#include <mach/at91rm9200_mc.h>
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-#include <mach/at91sam9_ddrsdr.h>
-#else
-#include <mach/at91sam9_sdramc.h>
-#endif
+#include <mach/at91_ramc.h>
#ifdef CONFIG_ARCH_AT91SAM9263
#define PLLALOCK_TIMEOUT 1000
#define PLLBLOCK_TIMEOUT 1000
+pmc .req r0
+sdramc .req r1
+ramc1 .req r2
+memctrl .req r3
+tmp1 .req r4
+tmp2 .req r5
/*
* Wait until master clock is ready (after switching master clock source)
*/
.macro wait_mckrdy
- mov r4, #MCKRDY_TIMEOUT
-1: sub r4, r4, #1
- cmp r4, #0
+ mov tmp2, #MCKRDY_TIMEOUT
+1: sub tmp2, tmp2, #1
+ cmp tmp2, #0
beq 2f
- ldr r3, [r1, #(AT91_PMC_SR - AT91_PMC)]
- tst r3, #AT91_PMC_MCKRDY
+ ldr tmp1, [pmc, #AT91_PMC_SR]
+ tst tmp1, #AT91_PMC_MCKRDY
beq 1b
2:
.endm
* Wait until master oscillator has stabilized.
*/
.macro wait_moscrdy
- mov r4, #MOSCRDY_TIMEOUT
-1: sub r4, r4, #1
- cmp r4, #0
+ mov tmp2, #MOSCRDY_TIMEOUT
+1: sub tmp2, tmp2, #1
+ cmp tmp2, #0
beq 2f
- ldr r3, [r1, #(AT91_PMC_SR - AT91_PMC)]
- tst r3, #AT91_PMC_MOSCS
+ ldr tmp1, [pmc, #AT91_PMC_SR]
+ tst tmp1, #AT91_PMC_MOSCS
beq 1b
2:
.endm
* Wait until PLLA has locked.
*/
.macro wait_pllalock
- mov r4, #PLLALOCK_TIMEOUT
-1: sub r4, r4, #1
- cmp r4, #0
+ mov tmp2, #PLLALOCK_TIMEOUT
+1: sub tmp2, tmp2, #1
+ cmp tmp2, #0
beq 2f
- ldr r3, [r1, #(AT91_PMC_SR - AT91_PMC)]
- tst r3, #AT91_PMC_LOCKA
+ ldr tmp1, [pmc, #AT91_PMC_SR]
+ tst tmp1, #AT91_PMC_LOCKA
beq 1b
2:
.endm
* Wait until PLLB has locked.
*/
.macro wait_pllblock
- mov r4, #PLLBLOCK_TIMEOUT
-1: sub r4, r4, #1
- cmp r4, #0
+ mov tmp2, #PLLBLOCK_TIMEOUT
+1: sub tmp2, tmp2, #1
+ cmp tmp2, #0
beq 2f
- ldr r3, [r1, #(AT91_PMC_SR - AT91_PMC)]
- tst r3, #AT91_PMC_LOCKB
+ ldr tmp1, [pmc, #AT91_PMC_SR]
+ tst tmp1, #AT91_PMC_LOCKB
beq 1b
2:
.endm
.text
+/* void at91_slow_clock(void __iomem *pmc, void __iomem *sdramc,
+ * void __iomem *ramc1, int memctrl)
+ */
ENTRY(at91_slow_clock)
/* Save registers on stack */
- stmfd sp!, {r0 - r12, lr}
+ stmfd sp!, {r4 - r12, lr}
/*
* Register usage:
- * R1 = Base address of AT91_PMC
- * R2 = Base address of RAM Controller (SDRAM, DDRSDR, or AT91_SYS)
- * R3 = temporary register
+ * R0 = Base address of AT91_PMC
+ * R1 = Base address of RAM Controller (SDRAM, DDRSDR, or AT91_SYS)
+ * R2 = Base address of second RAM Controller or 0 if not present
+ * R3 = Memory controller
* R4 = temporary register
- * R5 = Base address of second RAM Controller or 0 if not present
+ * R5 = temporary register
*/
- ldr r1, .at91_va_base_pmc
- ldr r2, .at91_va_base_sdramc
- ldr r5, .at91_va_base_ramc1
/* Drain write buffer */
- mov r0, #0
- mcr p15, 0, r0, c7, c10, 4
+ mov tmp1, #0
+ mcr p15, 0, tmp1, c7, c10, 4
+
+ cmp memctrl, #AT91_MEMCTRL_MC
+ bne ddr_sr_enable
-#ifdef CONFIG_ARCH_AT91RM9200
+ /*
+ * at91rm9200 Memory controller
+ */
/* Put SDRAM in self-refresh mode */
- mov r3, #1
- str r3, [r2, #AT91_SDRAMC_SRR]
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
+ mov tmp1, #1
+ str tmp1, [sdramc, #AT91RM9200_SDRAMC_SRR]
+ b sdr_sr_done
+
+ /*
+ * DDRSDR Memory controller
+ */
+ddr_sr_enable:
+ cmp memctrl, #AT91_MEMCTRL_DDRSDR
+ bne sdr_sr_enable
/* prepare for DDRAM self-refresh mode */
- ldr r3, [r2, #AT91_DDRSDRC_LPR]
- str r3, .saved_sam9_lpr
- bic r3, #AT91_DDRSDRC_LPCB
- orr r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH
+ ldr tmp1, [sdramc, #AT91_DDRSDRC_LPR]
+ str tmp1, .saved_sam9_lpr
+ bic tmp1, #AT91_DDRSDRC_LPCB
+ orr tmp1, #AT91_DDRSDRC_LPCB_SELF_REFRESH
/* figure out if we use the second ram controller */
- cmp r5, #0
- ldrne r4, [r5, #AT91_DDRSDRC_LPR]
- strne r4, .saved_sam9_lpr1
- bicne r4, #AT91_DDRSDRC_LPCB
- orrne r4, #AT91_DDRSDRC_LPCB_SELF_REFRESH
+ cmp ramc1, #0
+ ldrne tmp2, [ramc1, #AT91_DDRSDRC_LPR]
+ strne tmp2, .saved_sam9_lpr1
+ bicne tmp2, #AT91_DDRSDRC_LPCB
+ orrne tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH
/* Enable DDRAM self-refresh mode */
- str r3, [r2, #AT91_DDRSDRC_LPR]
- strne r4, [r5, #AT91_DDRSDRC_LPR]
-#else
+ str tmp1, [sdramc, #AT91_DDRSDRC_LPR]
+ strne tmp2, [ramc1, #AT91_DDRSDRC_LPR]
+
+ b sdr_sr_done
+
+ /*
+ * SDRAMC Memory controller
+ */
+sdr_sr_enable:
/* Enable SDRAM self-refresh mode */
- ldr r3, [r2, #AT91_SDRAMC_LPR]
- str r3, .saved_sam9_lpr
+ ldr tmp1, [sdramc, #AT91_SDRAMC_LPR]
+ str tmp1, .saved_sam9_lpr
- bic r3, #AT91_SDRAMC_LPCB
- orr r3, #AT91_SDRAMC_LPCB_SELF_REFRESH
- str r3, [r2, #AT91_SDRAMC_LPR]
-#endif
+ bic tmp1, #AT91_SDRAMC_LPCB
+ orr tmp1, #AT91_SDRAMC_LPCB_SELF_REFRESH
+ str tmp1, [sdramc, #AT91_SDRAMC_LPR]
+sdr_sr_done:
/* Save Master clock setting */
- ldr r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)]
- str r3, .saved_mckr
+ ldr tmp1, [pmc, #AT91_PMC_MCKR]
+ str tmp1, .saved_mckr
/*
* Set the Master clock source to slow clock
*/
- bic r3, r3, #AT91_PMC_CSS
- str r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)]
+ bic tmp1, tmp1, #AT91_PMC_CSS
+ str tmp1, [pmc, #AT91_PMC_MCKR]
wait_mckrdy
*
* See AT91RM9200 errata #27 and #28 for details.
*/
- mov r3, #0
- str r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)]
+ mov tmp1, #0
+ str tmp1, [pmc, #AT91_PMC_MCKR]
wait_mckrdy
#endif
/* Save PLLA setting and disable it */
- ldr r3, [r1, #(AT91_CKGR_PLLAR - AT91_PMC)]
- str r3, .saved_pllar
+ ldr tmp1, [pmc, #AT91_CKGR_PLLAR]
+ str tmp1, .saved_pllar
- mov r3, #AT91_PMC_PLLCOUNT
- orr r3, r3, #(1 << 29) /* bit 29 always set */
- str r3, [r1, #(AT91_CKGR_PLLAR - AT91_PMC)]
+ mov tmp1, #AT91_PMC_PLLCOUNT
+ orr tmp1, tmp1, #(1 << 29) /* bit 29 always set */
+ str tmp1, [pmc, #AT91_CKGR_PLLAR]
/* Save PLLB setting and disable it */
- ldr r3, [r1, #(AT91_CKGR_PLLBR - AT91_PMC)]
- str r3, .saved_pllbr
+ ldr tmp1, [pmc, #AT91_CKGR_PLLBR]
+ str tmp1, .saved_pllbr
- mov r3, #AT91_PMC_PLLCOUNT
- str r3, [r1, #(AT91_CKGR_PLLBR - AT91_PMC)]
+ mov tmp1, #AT91_PMC_PLLCOUNT
+ str tmp1, [pmc, #AT91_CKGR_PLLBR]
/* Turn off the main oscillator */
- ldr r3, [r1, #(AT91_CKGR_MOR - AT91_PMC)]
- bic r3, r3, #AT91_PMC_MOSCEN
- str r3, [r1, #(AT91_CKGR_MOR - AT91_PMC)]
+ ldr tmp1, [pmc, #AT91_CKGR_MOR]
+ bic tmp1, tmp1, #AT91_PMC_MOSCEN
+ str tmp1, [pmc, #AT91_CKGR_MOR]
/* Wait for interrupt */
- mcr p15, 0, r0, c7, c0, 4
+ mcr p15, 0, tmp1, c7, c0, 4
/* Turn on the main oscillator */
- ldr r3, [r1, #(AT91_CKGR_MOR - AT91_PMC)]
- orr r3, r3, #AT91_PMC_MOSCEN
- str r3, [r1, #(AT91_CKGR_MOR - AT91_PMC)]
+ ldr tmp1, [pmc, #AT91_CKGR_MOR]
+ orr tmp1, tmp1, #AT91_PMC_MOSCEN
+ str tmp1, [pmc, #AT91_CKGR_MOR]
wait_moscrdy
/* Restore PLLB setting */
- ldr r3, .saved_pllbr
- str r3, [r1, #(AT91_CKGR_PLLBR - AT91_PMC)]
+ ldr tmp1, .saved_pllbr
+ str tmp1, [pmc, #AT91_CKGR_PLLBR]
- tst r3, #(AT91_PMC_MUL & 0xff0000)
+ tst tmp1, #(AT91_PMC_MUL & 0xff0000)
bne 1f
- tst r3, #(AT91_PMC_MUL & ~0xff0000)
+ tst tmp1, #(AT91_PMC_MUL & ~0xff0000)
beq 2f
1:
wait_pllblock
2:
/* Restore PLLA setting */
- ldr r3, .saved_pllar
- str r3, [r1, #(AT91_CKGR_PLLAR - AT91_PMC)]
+ ldr tmp1, .saved_pllar
+ str tmp1, [pmc, #AT91_CKGR_PLLAR]
- tst r3, #(AT91_PMC_MUL & 0xff0000)
+ tst tmp1, #(AT91_PMC_MUL & 0xff0000)
bne 3f
- tst r3, #(AT91_PMC_MUL & ~0xff0000)
+ tst tmp1, #(AT91_PMC_MUL & ~0xff0000)
beq 4f
3:
wait_pllalock
*
* See AT91RM9200 errata #27 and #28 for details.
*/
- ldr r3, .saved_mckr
- tst r3, #AT91_PMC_PRES
+ ldr tmp1, .saved_mckr
+ tst tmp1, #AT91_PMC_PRES
beq 2f
- and r3, r3, #AT91_PMC_PRES
- str r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)]
+ and tmp1, tmp1, #AT91_PMC_PRES
+ str tmp1, [pmc, #AT91_PMC_MCKR]
wait_mckrdy
#endif
/*
* Restore master clock setting
*/
-2: ldr r3, .saved_mckr
- str r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)]
+2: ldr tmp1, .saved_mckr
+ str tmp1, [pmc, #AT91_PMC_MCKR]
wait_mckrdy
-#ifdef CONFIG_ARCH_AT91RM9200
- /* Do nothing - self-refresh is automatically disabled. */
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
+ /*
+ * at91rm9200 Memory controller
+ * Do nothing - self-refresh is automatically disabled.
+ */
+ cmp memctrl, #AT91_MEMCTRL_MC
+ beq ram_restored
+
+ /*
+ * DDRSDR Memory controller
+ */
+ cmp memctrl, #AT91_MEMCTRL_DDRSDR
+ bne sdr_en_restore
/* Restore LPR on AT91 with DDRAM */
- ldr r3, .saved_sam9_lpr
- str r3, [r2, #AT91_DDRSDRC_LPR]
+ ldr tmp1, .saved_sam9_lpr
+ str tmp1, [sdramc, #AT91_DDRSDRC_LPR]
/* if we use the second ram controller */
- cmp r5, #0
- ldrne r4, .saved_sam9_lpr1
- strne r4, [r5, #AT91_DDRSDRC_LPR]
+ cmp ramc1, #0
+ ldrne tmp2, .saved_sam9_lpr1
+ strne tmp2, [ramc1, #AT91_DDRSDRC_LPR]
+
+ b ram_restored
-#else
+ /*
+ * SDRAMC Memory controller
+ */
+sdr_en_restore:
/* Restore LPR on AT91 with SDRAM */
- ldr r3, .saved_sam9_lpr
- str r3, [r2, #AT91_SDRAMC_LPR]
-#endif
+ ldr tmp1, .saved_sam9_lpr
+ str tmp1, [sdramc, #AT91_SDRAMC_LPR]
+ram_restored:
/* Restore registers, and return */
- ldmfd sp!, {r0 - r12, pc}
+ ldmfd sp!, {r4 - r12, pc}
.saved_mckr:
.saved_sam9_lpr1:
.word 0
-.at91_va_base_pmc:
- .word AT91_VA_BASE_SYS + AT91_PMC
-
-#ifdef CONFIG_ARCH_AT91RM9200
-.at91_va_base_sdramc:
- .word AT91_VA_BASE_SYS
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-.at91_va_base_sdramc:
- .word AT91_VA_BASE_SYS + AT91_DDRSDRC0
-#else
-.at91_va_base_sdramc:
- .word AT91_VA_BASE_SYS + AT91_SDRAMC0
-#endif
-
-.at91_va_base_ramc1:
-#if defined(CONFIG_ARCH_AT91SAM9G45)
- .word AT91_VA_BASE_SYS + AT91_DDRSDRC1
-#else
- .word 0
-#endif
-
ENTRY(at91_slow_clock_sz)
.word .-at91_slow_clock
panic("Impossible to ioremap at91_rstc_base\n");
}
+void __iomem *at91_matrix_base;
+
+void __init at91_ioremap_matrix(u32 base_addr)
+{
+ at91_matrix_base = ioremap(base_addr, 512);
+ if (!at91_matrix_base)
+ panic("Impossible to ioremap at91_matrix_base\n");
+}
+
void __init at91_initialize(unsigned long main_clock)
{
at91_boot_soc.ioremap_registers();
Include support for IMX27 IPCAM platform. This includes specific
configurations for the board and its peripherals.
+config MACH_IMX27_DT
+ bool "Support i.MX27 platforms from device tree"
+ select SOC_IMX27
+ select USE_OF
+ help
+ Include support for Freescale i.MX27 based platforms
+ using the device tree for discovery
+
endif
if ARCH_IMX_V6_V7
obj-$(CONFIG_MACH_PCA100) += mach-pca100.o
obj-$(CONFIG_MACH_MXT_TD60) += mach-mxt_td60.o
obj-$(CONFIG_MACH_IMX27IPCAM) += mach-imx27ipcam.o
+obj-$(CONFIG_MACH_IMX27_DT) += imx27-dt.o
# i.MX31 based machines
obj-$(CONFIG_MACH_MX31ADS) += mach-mx31ads.o
params_phys-$(CONFIG_SOC_IMX6Q) := 0x10000100
initrd_phys-$(CONFIG_SOC_IMX6Q) := 0x10800000
+dtb-$(CONFIG_MACH_IMX51_DT) += imx51-babbage.dtb
+dtb-$(CONFIG_MACH_IMX53_DT) += imx53-ard.dtb imx53-evk.dtb \
+ imx53-qsb.dtb imx53-smd.dtb
dtb-$(CONFIG_SOC_IMX6Q) += imx6q-arm2.dtb \
imx6q-sabrelite.dtb
#include <linux/io.h>
#include <linux/module.h>
#include <linux/clkdev.h>
+#include <linux/of.h>
#include <asm/div64.h>
return 0;
}
+#ifdef CONFIG_OF
+int __init mx27_clocks_init_dt(void)
+{
+ struct device_node *np;
+ u32 fref = 26000000; /* default */
+
+ for_each_compatible_node(np, NULL, "fixed-clock") {
+ if (!of_device_is_compatible(np, "fsl,imx-osc26m"))
+ continue;
+
+ if (!of_property_read_u32(np, "clock-frequency", &fref))
+ break;
+ }
+
+ return mx27_clocks_init(fref);
+}
+#endif
--- /dev/null
+/*
+ * Copyright 2012 Sascha Hauer, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <mach/common.h>
+#include <mach/mx27.h>
+
+static const struct of_dev_auxdata imx27_auxdata_lookup[] __initconst = {
+ OF_DEV_AUXDATA("fsl,imx27-uart", MX27_UART1_BASE_ADDR, "imx21-uart.0", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-uart", MX27_UART2_BASE_ADDR, "imx21-uart.1", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-uart", MX27_UART3_BASE_ADDR, "imx21-uart.2", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-fec", MX27_FEC_BASE_ADDR, "imx27-fec.0", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-i2c", MX27_I2C1_BASE_ADDR, "imx-i2c.0", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-i2c", MX27_I2C2_BASE_ADDR, "imx-i2c.1", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-cspi", MX27_CSPI1_BASE_ADDR, "imx27-cspi.0", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-cspi", MX27_CSPI2_BASE_ADDR, "imx27-cspi.1", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-cspi", MX27_CSPI3_BASE_ADDR, "imx27-cspi.2", NULL),
+ OF_DEV_AUXDATA("fsl,imx27-wdt", MX27_WDOG_BASE_ADDR, "imx2-wdt.0", NULL),
+ { /* sentinel */ }
+};
+
+static int __init imx27_avic_add_irq_domain(struct device_node *np,
+ struct device_node *interrupt_parent)
+{
+ irq_domain_add_simple(np, 0);
+ return 0;
+}
+
+static int __init imx27_gpio_add_irq_domain(struct device_node *np,
+ struct device_node *interrupt_parent)
+{
+ static int gpio_irq_base = MXC_GPIO_IRQ_START + ARCH_NR_GPIOS;
+
+ irq_domain_add_simple(np, gpio_irq_base);
+
+ return 0;
+}
+
+static const struct of_device_id imx27_irq_match[] __initconst = {
+ { .compatible = "fsl,imx27-avic", .data = imx27_avic_add_irq_domain, },
+ { .compatible = "fsl,imx27-gpio", .data = imx27_gpio_add_irq_domain, },
+ { /* sentinel */ }
+};
+
+static void __init imx27_dt_init(void)
+{
+ of_irq_init(imx27_irq_match);
+
+ of_platform_populate(NULL, of_default_bus_match_table,
+ imx27_auxdata_lookup, NULL);
+}
+
+static void __init imx27_timer_init(void)
+{
+ mx27_clocks_init_dt();
+}
+
+static struct sys_timer imx27_timer = {
+ .init = imx27_timer_init,
+};
+
+static const char *imx27_dt_board_compat[] __initdata = {
+ "fsl,imx27",
+ NULL
+};
+
+DT_MACHINE_START(IMX27_DT, "Freescale i.MX27 (Device Tree Support)")
+ .map_io = mx27_map_io,
+ .init_early = imx27_init_early,
+ .init_irq = mx27_init_irq,
+ .handle_irq = imx27_handle_irq,
+ .timer = &imx27_timer,
+ .init_machine = imx27_dt_init,
+ .dt_compat = imx27_dt_board_compat,
+ .restart = mxc_restart,
+MACHINE_END
static const char *imx51_dt_board_compat[] __initdata = {
"fsl,imx51-babbage",
+ "fsl,imx51",
NULL
};
"fsl,imx53-evk",
"fsl,imx53-qsb",
"fsl,imx53-smd",
+ "fsl,imx53",
NULL
};
static const char *imx6q_dt_compat[] __initdata = {
"fsl,imx6q-arm2",
"fsl,imx6q-sabrelite",
+ "fsl,imx6q",
NULL,
};
menu "Marvell PXA168/910/MMP2 Implmentations"
+config MACH_MMP_DT
+ bool "Support MMP2 platforms from device tree"
+ select CPU_PXA168
+ select CPU_PXA910
+ select USE_OF
+ help
+ Include support for Marvell MMP2 based platforms using
+ the device tree. Needn't select any other machine while
+ MACH_MMP_DT is enabled.
+
config MACH_ASPENITE
bool "Marvell's PXA168 Aspenite Development Board"
select CPU_PXA168
obj-$(CONFIG_MACH_BROWNSTONE) += brownstone.o
obj-$(CONFIG_MACH_FLINT) += flint.o
obj-$(CONFIG_MACH_MARVELL_JASPER) += jasper.o
+obj-$(CONFIG_MACH_MMP_DT) += mmp-dt.o
obj-$(CONFIG_MACH_TETON_BGA) += teton_bga.o
obj-$(CONFIG_MACH_GPLUGD) += gplugd.o
--- /dev/null
+/*
+ * linux/arch/arm/mach-mmp/mmp-dt.c
+ *
+ * Copyright (C) 2012 Marvell Technology Group Ltd.
+ * Author: Haojian Zhuang <haojian.zhuang@marvell.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <asm/mach/arch.h>
+#include <mach/irqs.h>
+
+#include "common.h"
+
+extern struct sys_timer pxa168_timer;
+extern void __init icu_init_irq(void);
+
+static const struct of_dev_auxdata mmp_auxdata_lookup[] __initconst = {
+ OF_DEV_AUXDATA("mrvl,mmp-uart", 0xd4017000, "pxa2xx-uart.0", NULL),
+ OF_DEV_AUXDATA("mrvl,mmp-uart", 0xd4018000, "pxa2xx-uart.1", NULL),
+ OF_DEV_AUXDATA("mrvl,mmp-uart", 0xd4026000, "pxa2xx-uart.2", NULL),
+ OF_DEV_AUXDATA("mrvl,mmp-twsi", 0xd4011000, "pxa2xx-i2c.0", NULL),
+ OF_DEV_AUXDATA("mrvl,mmp-twsi", 0xd4025000, "pxa2xx-i2c.1", NULL),
+ OF_DEV_AUXDATA("mrvl,mmp-gpio", 0xd4019000, "pxa-gpio", NULL),
+ OF_DEV_AUXDATA("mrvl,mmp-rtc", 0xd4010000, "sa1100-rtc", NULL),
+ {}
+};
+
+static int __init mmp_intc_add_irq_domain(struct device_node *np,
+ struct device_node *parent)
+{
+ irq_domain_add_simple(np, 0);
+ return 0;
+}
+
+static int __init mmp_gpio_add_irq_domain(struct device_node *np,
+ struct device_node *parent)
+{
+ irq_domain_add_simple(np, IRQ_GPIO_START);
+ return 0;
+}
+
+static const struct of_device_id mmp_irq_match[] __initconst = {
+ { .compatible = "mrvl,mmp-intc", .data = mmp_intc_add_irq_domain, },
+ { .compatible = "mrvl,mmp-gpio", .data = mmp_gpio_add_irq_domain, },
+ {}
+};
+
+static void __init mmp_dt_init(void)
+{
+
+ of_irq_init(mmp_irq_match);
+
+ of_platform_populate(NULL, of_default_bus_match_table,
+ mmp_auxdata_lookup, NULL);
+}
+
+static const char *pxa168_dt_board_compat[] __initdata = {
+ "mrvl,pxa168-aspenite",
+ NULL,
+};
+
+DT_MACHINE_START(PXA168_DT, "Marvell PXA168 (Device Tree Support)")
+ .map_io = mmp_map_io,
+ .init_irq = icu_init_irq,
+ .timer = &pxa168_timer,
+ .init_machine = mmp_dt_init,
+ .dt_compat = pxa168_dt_board_compat,
+MACHINE_END
static APBC_CLK(ssp5, PXA168_SSP5, 4, 0);
static APBC_CLK(gpio, PXA168_GPIO, 0, 13000000);
static APBC_CLK(keypad, PXA168_KPC, 0, 32000);
+static APBC_CLK(rtc, PXA168_RTC, 8, 32768);
static APMU_CLK(nand, NAND, 0x19b, 156000000);
static APMU_CLK(lcd, LCD, 0x7f, 312000000);
INIT_CLKREG(&clk_keypad, "pxa27x-keypad", NULL),
INIT_CLKREG(&clk_eth, "pxa168-eth", "MFUCLK"),
INIT_CLKREG(&clk_usb, "pxa168-ehci", "PXA168-USBCLK"),
+ INIT_CLKREG(&clk_rtc, "sa1100-rtc", NULL),
};
static int __init pxa168_init(void)
config MACH_OMAP_GENERIC
bool "Generic OMAP2+ board"
depends on ARCH_OMAP2PLUS
- select USE_OF
default y
help
Support for generic TI OMAP2+ boards using Flattened Device Tree.
* published by the Free Software Foundation.
*/
#include <linux/io.h>
+#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/irqdomain.h>
#include <linux/i2c/twl.h>
#include "common.h"
#include "common-board-devices.h"
-/*
- * XXX: Still needed to boot until the i2c & twl driver is adapted to
- * device-tree
- */
-#ifdef CONFIG_ARCH_OMAP4
-static struct twl4030_platform_data sdp4430_twldata = {
- .irq_base = TWL6030_IRQ_BASE,
- .irq_end = TWL6030_IRQ_END,
-};
-
-static void __init omap4_i2c_init(void)
-{
- omap4_pmic_init("twl6030", &sdp4430_twldata);
-}
+#if !(defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3))
+#define omap_intc_of_init NULL
+#endif
+#ifndef CONFIG_ARCH_OMAP4
+#define gic_of_init NULL
#endif
-#ifdef CONFIG_ARCH_OMAP3
-static struct twl4030_platform_data beagle_twldata = {
- .irq_base = TWL4030_IRQ_BASE,
- .irq_end = TWL4030_IRQ_END,
+static struct of_device_id irq_match[] __initdata = {
+ { .compatible = "ti,omap2-intc", .data = omap_intc_of_init, },
+ { .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
+ { }
};
-static void __init omap3_i2c_init(void)
+static void __init omap_init_irq(void)
{
- omap3_pmic_init("twl4030", &beagle_twldata);
+ of_irq_init(irq_match);
}
-#endif
static struct of_device_id omap_dt_match_table[] __initdata = {
{ .compatible = "simple-bus", },
{ }
};
-static struct of_device_id intc_match[] __initdata = {
- { .compatible = "ti,omap3-intc", },
- { .compatible = "arm,cortex-a9-gic", },
- { }
-};
-
static void __init omap_generic_init(void)
{
- struct device_node *node = of_find_matching_node(NULL, intc_match);
- if (node)
- irq_domain_add_legacy(node, 32, 0, 0, &irq_domain_simple_ops, NULL);
-
omap_sdrc_init(NULL, NULL);
of_platform_populate(NULL, omap_dt_match_table, NULL, NULL);
}
-#ifdef CONFIG_ARCH_OMAP4
-static void __init omap4_init(void)
-{
- omap4_i2c_init();
- omap_generic_init();
-}
-#endif
-
-#ifdef CONFIG_ARCH_OMAP3
-static void __init omap3_init(void)
-{
- omap3_i2c_init();
- omap_generic_init();
-}
-#endif
-
-#if defined(CONFIG_SOC_OMAP2420)
+#ifdef CONFIG_SOC_OMAP2420
static const char *omap242x_boards_compat[] __initdata = {
"ti,omap2420",
NULL,
};
DT_MACHINE_START(OMAP242X_DT, "Generic OMAP2420 (Flattened Device Tree)")
- .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap242x_map_io,
.init_early = omap2420_init_early,
- .init_irq = omap2_init_irq,
+ .init_irq = omap_init_irq,
.handle_irq = omap2_intc_handle_irq,
.init_machine = omap_generic_init,
.timer = &omap2_timer,
MACHINE_END
#endif
-#if defined(CONFIG_SOC_OMAP2430)
+#ifdef CONFIG_SOC_OMAP2430
static const char *omap243x_boards_compat[] __initdata = {
"ti,omap2430",
NULL,
};
DT_MACHINE_START(OMAP243X_DT, "Generic OMAP2430 (Flattened Device Tree)")
- .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap243x_map_io,
.init_early = omap2430_init_early,
- .init_irq = omap2_init_irq,
+ .init_irq = omap_init_irq,
.handle_irq = omap2_intc_handle_irq,
.init_machine = omap_generic_init,
.timer = &omap2_timer,
MACHINE_END
#endif
-#if defined(CONFIG_ARCH_OMAP3)
+#ifdef CONFIG_ARCH_OMAP3
+static struct twl4030_platform_data beagle_twldata = {
+ .irq_base = TWL4030_IRQ_BASE,
+ .irq_end = TWL4030_IRQ_END,
+};
+
+static void __init omap3_i2c_init(void)
+{
+ omap3_pmic_init("twl4030", &beagle_twldata);
+}
+
+static void __init omap3_init(void)
+{
+ omap3_i2c_init();
+ omap_generic_init();
+}
+
static const char *omap3_boards_compat[] __initdata = {
"ti,omap3",
NULL,
};
DT_MACHINE_START(OMAP3_DT, "Generic OMAP3 (Flattened Device Tree)")
- .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap3430_init_early,
- .init_irq = omap3_init_irq,
+ .init_irq = omap_init_irq,
.handle_irq = omap3_intc_handle_irq,
.init_machine = omap3_init,
.timer = &omap3_timer,
MACHINE_END
#endif
-#if defined(CONFIG_ARCH_OMAP4)
+#ifdef CONFIG_ARCH_OMAP4
+static struct twl4030_platform_data sdp4430_twldata = {
+ .irq_base = TWL6030_IRQ_BASE,
+ .irq_end = TWL6030_IRQ_END,
+};
+
+static void __init omap4_i2c_init(void)
+{
+ omap4_pmic_init("twl6030", &sdp4430_twldata);
+}
+
+static void __init omap4_init(void)
+{
+ omap4_i2c_init();
+ omap_generic_init();
+}
+
static const char *omap4_boards_compat[] __initdata = {
"ti,omap4",
NULL,
};
DT_MACHINE_START(OMAP4_DT, "Generic OMAP4 (Flattened Device Tree)")
- .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap4_map_io,
.init_early = omap4430_init_early,
- .init_irq = gic_init_irq,
+ .init_irq = omap_init_irq,
.handle_irq = gic_handle_irq,
.init_machine = omap4_init,
.timer = &omap4_timer,
extern void __iomem *omap4_get_l2cache_base(void);
#endif
+struct device_node;
+#ifdef CONFIG_OF
+int __init omap_intc_of_init(struct device_node *node,
+ struct device_node *parent);
+#else
+int __init omap_intc_of_init(struct device_node *node,
+ struct device_node *parent)
+{
+ return 0;
+}
+#endif
+
#ifdef CONFIG_SMP
extern void __iomem *omap4_get_scu_base(void);
#else
* for more details.
*/
#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <asm/exception.h>
#include <asm/mach/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
#include <mach/hardware.h>
},
};
+static struct irq_domain *domain;
+
/* Structure to save interrupt controller context */
struct omap3_intc_regs {
u32 sysconfig;
IRQ_NOREQUEST | IRQ_NOPROBE, 0);
}
-static void __init omap_init_irq(u32 base, int nr_irqs)
+static void __init omap_init_irq(u32 base, int nr_irqs,
+ struct device_node *node)
{
void __iomem *omap_irq_base;
unsigned long nr_of_irqs = 0;
unsigned int nr_banks = 0;
- int i, j;
+ int i, j, irq_base;
omap_irq_base = ioremap(base, SZ_4K);
if (WARN_ON(!omap_irq_base))
return;
+ irq_base = irq_alloc_descs(-1, 0, nr_irqs, 0);
+ if (irq_base < 0) {
+ pr_warn("Couldn't allocate IRQ numbers\n");
+ irq_base = 0;
+ }
+
+ domain = irq_domain_add_legacy(node, nr_irqs, irq_base, 0,
+ &irq_domain_simple_ops, NULL);
+
for (i = 0; i < ARRAY_SIZE(irq_banks); i++) {
struct omap_irq_bank *bank = irq_banks + i;
/* Static mapping, never released */
bank->base_reg = ioremap(base, SZ_4K);
if (!bank->base_reg) {
- printk(KERN_ERR "Could not ioremap irq bank%i\n", i);
+ pr_err("Could not ioremap irq bank%i\n", i);
continue;
}
omap_irq_bank_init_one(bank);
for (j = 0; j < bank->nr_irqs; j += 32)
- omap_alloc_gc(bank->base_reg + j, j, 32);
+ omap_alloc_gc(bank->base_reg + j, j + irq_base, 32);
nr_of_irqs += bank->nr_irqs;
nr_banks++;
}
- printk(KERN_INFO "Total of %ld interrupts on %d active controller%s\n",
- nr_of_irqs, nr_banks, nr_banks > 1 ? "s" : "");
+ pr_info("Total of %ld interrupts on %d active controller%s\n",
+ nr_of_irqs, nr_banks, nr_banks > 1 ? "s" : "");
}
void __init omap2_init_irq(void)
{
- omap_init_irq(OMAP24XX_IC_BASE, 96);
+ omap_init_irq(OMAP24XX_IC_BASE, 96, NULL);
}
void __init omap3_init_irq(void)
{
- omap_init_irq(OMAP34XX_IC_BASE, 96);
+ omap_init_irq(OMAP34XX_IC_BASE, 96, NULL);
}
void __init ti81xx_init_irq(void)
{
- omap_init_irq(OMAP34XX_IC_BASE, 128);
+ omap_init_irq(OMAP34XX_IC_BASE, 128, NULL);
}
static inline void omap_intc_handle_irq(void __iomem *base_addr, struct pt_regs *regs)
irqnr = readl_relaxed(base_addr + INTCPS_SIR_IRQ_OFFSET);
irqnr &= ACTIVEIRQ_MASK;
- if (irqnr)
+ if (irqnr) {
+ irqnr = irq_find_mapping(domain, irqnr);
handle_IRQ(irqnr, regs);
+ }
} while (irqnr);
}
omap_intc_handle_irq(base_addr, regs);
}
+int __init omap_intc_of_init(struct device_node *node,
+ struct device_node *parent)
+{
+ struct resource res;
+ u32 nr_irqs = 96;
+
+ if (WARN_ON(!node))
+ return -ENODEV;
+
+ if (of_address_to_resource(node, 0, &res)) {
+ WARN(1, "unable to get intc registers\n");
+ return -EINVAL;
+ }
+
+ if (of_property_read_u32(node, "ti,intc-size", &nr_irqs))
+ pr_warn("unable to get intc-size, default to %d\n", nr_irqs);
+
+ omap_init_irq(res.start, nr_irqs, of_node_get(node));
+
+ return 0;
+}
+
#ifdef CONFIG_ARCH_OMAP3
static struct omap3_intc_regs intc_context[ARRAY_SIZE(irq_banks)];
static int __init omap2_common_pm_late_init(void)
{
+ /*
+ * In the case of DT, the PMIC and SR initialization will be done using
+ * a completely different mechanism.
+ * Disable this part if a DT blob is available.
+ */
+ if (of_have_populated_dt())
+ return 0;
+
/* Init the voltage layer */
omap_pmic_late_init();
omap_voltage_late_init();
menu "Versatile Express platform type"
depends on ARCH_VEXPRESS
+config ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA
+ bool
+ select ARM_ERRATA_720789
+ select ARM_ERRATA_751472
+ select PL310_ERRATA_753970 if CACHE_PL310
+ help
+ Provides common dependencies for Versatile Express platforms
+ based on Cortex-A5 and Cortex-A9 processors. In order to
+ build a working kernel, you must also enable relevant core
+ tile support or Flattened Device Tree based support options.
+
config ARCH_VEXPRESS_CA9X4
bool "Versatile Express Cortex-A9x4 tile"
+ select ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA
+ select ARM_GIC
select CPU_V7
+ select HAVE_SMP
+ select MIGHT_HAVE_CACHE_L2X0
+
+config ARCH_VEXPRESS_DT
+ bool "Device Tree support for Versatile Express platforms"
+ select ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA
select ARM_GIC
- select ARM_ERRATA_720789
- select ARM_ERRATA_751472
- select PL310_ERRATA_753970
+ select ARM_PATCH_PHYS_VIRT
+ select AUTO_ZRELADDR
+ select CPU_V7
select HAVE_SMP
select MIGHT_HAVE_CACHE_L2X0
+ select USE_OF
+ help
+ New Versatile Express platforms require Flattened Device Tree to
+ be passed to the kernel.
+
+ This option enables support for systems using Cortex processor based
+ ARM core and logic (FPGA) tiles on the Versatile Express motherboard,
+ for example:
+
+ - CoreTile Express A5x2 (V2P-CA5s)
+ - CoreTile Express A9x4 (V2P-CA9)
+ - CoreTile Express A15x2 (V2P-CA15)
+ - LogicTile Express 13MG (V2F-2XV6) with A5, A7, A9 or A15 SMMs
+ (Soft Macrocell Models)
+ - Versatile Express RTSMs (Models)
+
+ You must boot using a Flattened Device Tree in order to use these
+ platforms. The traditional (ATAGs) boot method is not usable on
+ these boards with this option.
+
+ If your bootloader supports Flattened Device Tree based booting,
+ say Y here.
endmenu
+# Those numbers are used only by the non-DT V2P-CA9 platform
+# The DT-enabled ones require CONFIG_AUTO_ZRELADDR=y
zreladdr-y += 0x60008000
params_phys-y := 0x60000100
initrd_phys-y := 0x60800000
+
+dtb-$(CONFIG_ARCH_VEXPRESS_DT) += vexpress-v2p-ca5s.dtb \
+ vexpress-v2p-ca9.dtb \
+ vexpress-v2p-ca15-tc1.dtb
/* Tile's peripherals static mappings should start here */
#define V2T_PERIPH 0xf8200000
+
+void vexpress_dt_smp_map_io(void);
* published by the Free Software Foundation.
*/
-#define DEBUG_LL_UART_OFFSET 0x00009000
+#define DEBUG_LL_PHYS_BASE 0x10000000
+#define DEBUG_LL_UART_OFFSET 0x00009000
+
+#define DEBUG_LL_PHYS_BASE_RS1 0x1c000000
+#define DEBUG_LL_UART_OFFSET_RS1 0x00090000
+
+#define DEBUG_LL_VIRT_BASE 0xf8000000
.macro addruart,rp,rv,tmp
- mov \rp, #DEBUG_LL_UART_OFFSET
- orr \rv, \rp, #0xf8000000 @ virtual base
- orr \rp, \rp, #0x10000000 @ physical base
+
+ @ Make an educated guess regarding the memory map:
+ @ - the original A9 core tile, which has MPCore peripherals
+ @ located at 0x1e000000, should use UART at 0x10009000
+ @ - all other (RS1 complaint) tiles use UART mapped
+ @ at 0x1c090000
+ mrc p15, 4, \tmp, c15, c0, 0
+ cmp \tmp, #0x1e000000
+
+ @ Original memory map
+ moveq \rp, #DEBUG_LL_UART_OFFSET
+ orreq \rv, \rp, #DEBUG_LL_VIRT_BASE
+ orreq \rp, \rp, #DEBUG_LL_PHYS_BASE
+
+ @ RS1 memory map
+ movne \rp, #DEBUG_LL_UART_OFFSET_RS1
+ orrne \rv, \rp, #DEBUG_LL_VIRT_BASE
+ orrne \rp, \rp, #DEBUG_LL_PHYS_BASE_RS1
+
.endm
#include <asm/hardware/debug-pl01x.S>
#define IRQ_LOCALTIMER 29
#define IRQ_LOCALWDOG 30
-#define NR_IRQS 128
+#define NR_IRQS 256
void v2m_flags_set(u32 data);
/*
+ * Miscellaneous
+ */
+#define SYS_MISC_MASTERSITE (1 << 14)
+#define SYS_PROCIDx_HBI_MASK 0xfff
+
+/*
* Core tile IDs
*/
#define V2M_CT_ID_CA9 0x0c000191
#define AMBA_UART_CR(base) (*(volatile unsigned char *)((base) + 0x30))
#define AMBA_UART_FR(base) (*(volatile unsigned char *)((base) + 0x18))
-#define get_uart_base() (0x10000000 + 0x00009000)
+#define UART_BASE 0x10009000
+#define UART_BASE_RS1 0x1c090000
+
+static unsigned long get_uart_base(void)
+{
+ unsigned long mpcore_periph;
+
+ /*
+ * Make an educated guess regarding the memory map:
+ * - the original A9 core tile, which has MPCore peripherals
+ * located at 0x1e000000, should use UART at 0x10009000
+ * - all other (RS1 complaint) tiles use UART mapped
+ * at 0x1c090000
+ */
+ asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (mpcore_periph));
+
+ if (mpcore_periph == 0x1e000000)
+ return UART_BASE;
+ else
+ return UART_BASE_RS1;
+}
/*
* This does not append a newline
#include <linux/errno.h>
#include <linux/smp.h>
#include <linux/io.h>
+#include <linux/of_fdt.h>
+
+#include <asm/smp_scu.h>
+#include <asm/hardware/gic.h>
+#include <asm/mach/map.h>
#include <mach/motherboard.h>
extern void versatile_secondary_startup(void);
+#if defined(CONFIG_OF)
+
+static enum {
+ GENERIC_SCU,
+ CORTEX_A9_SCU,
+} vexpress_dt_scu __initdata = GENERIC_SCU;
+
+static struct map_desc vexpress_dt_cortex_a9_scu_map __initdata = {
+ .virtual = V2T_PERIPH,
+ /* .pfn set in vexpress_dt_init_cortex_a9_scu() */
+ .length = SZ_128,
+ .type = MT_DEVICE,
+};
+
+static void *vexpress_dt_cortex_a9_scu_base __initdata;
+
+const static char *vexpress_dt_cortex_a9_match[] __initconst = {
+ "arm,cortex-a5-scu",
+ "arm,cortex-a9-scu",
+ NULL
+};
+
+static int __init vexpress_dt_find_scu(unsigned long node,
+ const char *uname, int depth, void *data)
+{
+ if (of_flat_dt_match(node, vexpress_dt_cortex_a9_match)) {
+ phys_addr_t phys_addr;
+ __be32 *reg = of_get_flat_dt_prop(node, "reg", NULL);
+
+ if (WARN_ON(!reg))
+ return -EINVAL;
+
+ phys_addr = be32_to_cpup(reg);
+ vexpress_dt_scu = CORTEX_A9_SCU;
+
+ vexpress_dt_cortex_a9_scu_map.pfn = __phys_to_pfn(phys_addr);
+ iotable_init(&vexpress_dt_cortex_a9_scu_map, 1);
+ vexpress_dt_cortex_a9_scu_base = ioremap(phys_addr, SZ_256);
+ if (WARN_ON(!vexpress_dt_cortex_a9_scu_base))
+ return -EFAULT;
+ }
+
+ return 0;
+}
+
+void __init vexpress_dt_smp_map_io(void)
+{
+ if (initial_boot_params)
+ WARN_ON(of_scan_flat_dt(vexpress_dt_find_scu, NULL));
+}
+
+static int __init vexpress_dt_cpus_num(unsigned long node, const char *uname,
+ int depth, void *data)
+{
+ static int prev_depth = -1;
+ static int nr_cpus = -1;
+
+ if (prev_depth > depth && nr_cpus > 0)
+ return nr_cpus;
+
+ if (nr_cpus < 0 && strcmp(uname, "cpus") == 0)
+ nr_cpus = 0;
+
+ if (nr_cpus >= 0) {
+ const char *device_type = of_get_flat_dt_prop(node,
+ "device_type", NULL);
+
+ if (device_type && strcmp(device_type, "cpu") == 0)
+ nr_cpus++;
+ }
+
+ prev_depth = depth;
+
+ return 0;
+}
+
+static void __init vexpress_dt_smp_init_cpus(void)
+{
+ int ncores = 0, i;
+
+ switch (vexpress_dt_scu) {
+ case GENERIC_SCU:
+ ncores = of_scan_flat_dt(vexpress_dt_cpus_num, NULL);
+ break;
+ case CORTEX_A9_SCU:
+ ncores = scu_get_core_count(vexpress_dt_cortex_a9_scu_base);
+ break;
+ default:
+ WARN_ON(1);
+ break;
+ }
+
+ if (ncores < 2)
+ return;
+
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
+ }
+
+ for (i = 0; i < ncores; ++i)
+ set_cpu_possible(i, true);
+
+ set_smp_cross_call(gic_raise_softirq);
+}
+
+static void __init vexpress_dt_smp_prepare_cpus(unsigned int max_cpus)
+{
+ int i;
+
+ switch (vexpress_dt_scu) {
+ case GENERIC_SCU:
+ for (i = 0; i < max_cpus; i++)
+ set_cpu_present(i, true);
+ break;
+ case CORTEX_A9_SCU:
+ scu_enable(vexpress_dt_cortex_a9_scu_base);
+ break;
+ default:
+ WARN_ON(1);
+ break;
+ }
+}
+
+#else
+
+static void __init vexpress_dt_smp_init_cpus(void)
+{
+ WARN_ON(1);
+}
+
+void __init vexpress_dt_smp_prepare_cpus(unsigned int max_cpus)
+{
+ WARN_ON(1);
+}
+
+#endif
+
/*
* Initialise the CPU possible map early - this describes the CPUs
* which may be present or become present in the system.
*/
void __init smp_init_cpus(void)
{
- ct_desc->init_cpu_map();
+ if (ct_desc)
+ ct_desc->init_cpu_map();
+ else
+ vexpress_dt_smp_init_cpus();
+
}
void __init platform_smp_prepare_cpus(unsigned int max_cpus)
* Initialise the present map, which describes the set of CPUs
* actually populated at the present time.
*/
- ct_desc->smp_enable(max_cpus);
+ if (ct_desc)
+ ct_desc->smp_enable(max_cpus);
+ else
+ vexpress_dt_smp_prepare_cpus(max_cpus);
/*
* Write the address of secondary startup into the
#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <linux/init.h>
+#include <linux/of_address.h>
+#include <linux/of_fdt.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/smsc911x.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include <asm/hardware/arm_timer.h>
+#include <asm/hardware/cache-l2x0.h>
+#include <asm/hardware/gic.h>
#include <asm/hardware/timer-sp.h>
#include <asm/hardware/sp810.h>
#include <asm/hardware/gic.h>
ct_desc = ct_descs[i];
if (!ct_desc)
- panic("vexpress: failed to populate core tile description "
- "for tile ID 0x%8x\n", current_tile_id);
+ panic("vexpress: this kernel does not support core tile ID 0x%08x when booting via ATAGs.\n"
+ "You may need a device tree blob or a different kernel to boot on this board.\n",
+ current_tile_id);
}
static void __init v2m_map_io(void)
.init_machine = v2m_init,
.restart = v2m_restart,
MACHINE_END
+
+#if defined(CONFIG_ARCH_VEXPRESS_DT)
+
+static struct map_desc v2m_rs1_io_desc __initdata = {
+ .virtual = V2M_PERIPH,
+ .pfn = __phys_to_pfn(0x1c000000),
+ .length = SZ_2M,
+ .type = MT_DEVICE,
+};
+
+static int __init v2m_dt_scan_memory_map(unsigned long node, const char *uname,
+ int depth, void *data)
+{
+ const char **map = data;
+
+ if (strcmp(uname, "motherboard") != 0)
+ return 0;
+
+ *map = of_get_flat_dt_prop(node, "arm,v2m-memory-map", NULL);
+
+ return 1;
+}
+
+void __init v2m_dt_map_io(void)
+{
+ const char *map = NULL;
+
+ of_scan_flat_dt(v2m_dt_scan_memory_map, &map);
+
+ if (map && strcmp(map, "rs1") == 0)
+ iotable_init(&v2m_rs1_io_desc, 1);
+ else
+ iotable_init(v2m_io_desc, ARRAY_SIZE(v2m_io_desc));
+
+#if defined(CONFIG_SMP)
+ vexpress_dt_smp_map_io();
+#endif
+}
+
+static struct clk_lookup v2m_dt_lookups[] = {
+ { /* AMBA bus clock */
+ .con_id = "apb_pclk",
+ .clk = &dummy_apb_pclk,
+ }, { /* SP804 timers */
+ .dev_id = "sp804",
+ .con_id = "v2m-timer0",
+ .clk = &v2m_sp804_clk,
+ }, { /* SP804 timers */
+ .dev_id = "sp804",
+ .con_id = "v2m-timer1",
+ .clk = &v2m_sp804_clk,
+ }, { /* PL180 MMCI */
+ .dev_id = "mb:mmci", /* 10005000.mmci */
+ .clk = &osc2_clk,
+ }, { /* PL050 KMI0 */
+ .dev_id = "10006000.kmi",
+ .clk = &osc2_clk,
+ }, { /* PL050 KMI1 */
+ .dev_id = "10007000.kmi",
+ .clk = &osc2_clk,
+ }, { /* PL011 UART0 */
+ .dev_id = "10009000.uart",
+ .clk = &osc2_clk,
+ }, { /* PL011 UART1 */
+ .dev_id = "1000a000.uart",
+ .clk = &osc2_clk,
+ }, { /* PL011 UART2 */
+ .dev_id = "1000b000.uart",
+ .clk = &osc2_clk,
+ }, { /* PL011 UART3 */
+ .dev_id = "1000c000.uart",
+ .clk = &osc2_clk,
+ }, { /* SP805 WDT */
+ .dev_id = "1000f000.wdt",
+ .clk = &v2m_ref_clk,
+ }, { /* PL111 CLCD */
+ .dev_id = "1001f000.clcd",
+ .clk = &osc1_clk,
+ },
+ /* RS1 memory map */
+ { /* PL180 MMCI */
+ .dev_id = "mb:mmci", /* 1c050000.mmci */
+ .clk = &osc2_clk,
+ }, { /* PL050 KMI0 */
+ .dev_id = "1c060000.kmi",
+ .clk = &osc2_clk,
+ }, { /* PL050 KMI1 */
+ .dev_id = "1c070000.kmi",
+ .clk = &osc2_clk,
+ }, { /* PL011 UART0 */
+ .dev_id = "1c090000.uart",
+ .clk = &osc2_clk,
+ }, { /* PL011 UART1 */
+ .dev_id = "1c0a0000.uart",
+ .clk = &osc2_clk,
+ }, { /* PL011 UART2 */
+ .dev_id = "1c0b0000.uart",
+ .clk = &osc2_clk,
+ }, { /* PL011 UART3 */
+ .dev_id = "1c0c0000.uart",
+ .clk = &osc2_clk,
+ }, { /* SP805 WDT */
+ .dev_id = "1c0f0000.wdt",
+ .clk = &v2m_ref_clk,
+ }, { /* PL111 CLCD */
+ .dev_id = "1c1f0000.clcd",
+ .clk = &osc1_clk,
+ },
+};
+
+void __init v2m_dt_init_early(void)
+{
+ struct device_node *node;
+ u32 dt_hbi;
+
+ node = of_find_compatible_node(NULL, NULL, "arm,vexpress-sysreg");
+ v2m_sysreg_base = of_iomap(node, 0);
+ if (WARN_ON(!v2m_sysreg_base))
+ return;
+
+ /* Confirm board type against DT property, if available */
+ if (of_property_read_u32(allnodes, "arm,hbi", &dt_hbi) == 0) {
+ u32 misc = readl(v2m_sysreg_base + V2M_SYS_MISC);
+ u32 id = readl(v2m_sysreg_base + (misc & SYS_MISC_MASTERSITE ?
+ V2M_SYS_PROCID1 : V2M_SYS_PROCID0));
+ u32 hbi = id & SYS_PROCIDx_HBI_MASK;
+
+ if (WARN_ON(dt_hbi != hbi))
+ pr_warning("vexpress: DT HBI (%x) is not matching "
+ "hardware (%x)!\n", dt_hbi, hbi);
+ }
+
+ clkdev_add_table(v2m_dt_lookups, ARRAY_SIZE(v2m_dt_lookups));
+ versatile_sched_clock_init(v2m_sysreg_base + V2M_SYS_24MHZ, 24000000);
+}
+
+static struct of_device_id vexpress_irq_match[] __initdata = {
+ { .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
+ {}
+};
+
+static void __init v2m_dt_init_irq(void)
+{
+ of_irq_init(vexpress_irq_match);
+}
+
+static void __init v2m_dt_timer_init(void)
+{
+ struct device_node *node;
+ const char *path;
+ int err;
+
+ node = of_find_compatible_node(NULL, NULL, "arm,sp810");
+ v2m_sysctl_init(of_iomap(node, 0));
+
+ err = of_property_read_string(of_aliases, "arm,v2m_timer", &path);
+ if (WARN_ON(err))
+ return;
+ node = of_find_node_by_path(path);
+ v2m_sp804_init(of_iomap(node, 0), irq_of_parse_and_map(node, 0));
+}
+
+static struct sys_timer v2m_dt_timer = {
+ .init = v2m_dt_timer_init,
+};
+
+static struct of_dev_auxdata v2m_dt_auxdata_lookup[] __initdata = {
+ OF_DEV_AUXDATA("arm,vexpress-flash", V2M_NOR0, "physmap-flash",
+ &v2m_flash_data),
+ OF_DEV_AUXDATA("arm,primecell", V2M_MMCI, "mb:mmci", &v2m_mmci_data),
+ /* RS1 memory map */
+ OF_DEV_AUXDATA("arm,vexpress-flash", 0x08000000, "physmap-flash",
+ &v2m_flash_data),
+ OF_DEV_AUXDATA("arm,primecell", 0x1c050000, "mb:mmci", &v2m_mmci_data),
+ {}
+};
+
+static void __init v2m_dt_init(void)
+{
+ l2x0_of_init(0x00400000, 0xfe0fffff);
+ of_platform_populate(NULL, of_default_bus_match_table,
+ v2m_dt_auxdata_lookup, NULL);
+ pm_power_off = v2m_power_off;
+}
+
+const static char *v2m_dt_match[] __initconst = {
+ "arm,vexpress",
+ NULL,
+};
+
+DT_MACHINE_START(VEXPRESS_DT, "ARM-Versatile Express")
+ .dt_compat = v2m_dt_match,
+ .map_io = v2m_dt_map_io,
+ .init_early = v2m_dt_init_early,
+ .init_irq = v2m_dt_init_irq,
+ .timer = &v2m_dt_timer,
+ .init_machine = v2m_dt_init,
+ .handle_irq = gic_handle_irq,
+ .restart = v2m_restart,
+MACHINE_END
+
+#endif
unsigned long ckih1, unsigned long ckih2);
extern int mx53_clocks_init(unsigned long ckil, unsigned long osc,
unsigned long ckih1, unsigned long ckih2);
+extern int mx27_clocks_init_dt(void);
extern int mx51_clocks_init_dt(void);
extern int mx53_clocks_init_dt(void);
extern int mx6q_clocks_init(void);
select CLKDEV_LOOKUP
select CLKSRC_MMIO
select GENERIC_IRQ_CHIP
+ select IRQ_DOMAIN
select HAVE_IDE
select NEED_MACH_MEMORY_H
help
select CLKDEV_LOOKUP
select GENERIC_IRQ_CHIP
select OMAP_DM_TIMER
+ select USE_OF
+ select PROC_DEVICETREE if PROC_FS
help
"Systems based on OMAP2, OMAP3 or OMAP4"
oh_cnt = of_property_count_strings(node, "ti,hwmods");
if (!oh_cnt || IS_ERR_VALUE(oh_cnt)) {
- dev_warn(&pdev->dev, "No 'hwmods' to build omap_device\n");
+ dev_dbg(&pdev->dev, "No 'hwmods' to build omap_device\n");
return -ENODEV;
}
return at32_usarts[id];
}
-struct platform_device *atmel_default_console_device;
-
void __init at32_setup_serial_console(unsigned int usart_id)
{
atmel_default_console_device = at32_usarts[usart_id];
* - Two channels combine to create a free-running 32 bit counter
* with a base rate of 5+ MHz, packaged as a clocksource (with
* resolution better than 200 nsec).
+ * - Some chips support 32 bit counter. A single channel is used for
+ * this 32 bit free-running counter. the second channel is not used.
*
* - The third channel may be used to provide a 16-bit clockevent
* source, used in either periodic or oneshot mode. This runs
return (upper << 16) | lower;
}
+static cycle_t tc_get_cycles32(struct clocksource *cs)
+{
+ return __raw_readl(tcaddr + ATMEL_TC_REG(0, CV));
+}
+
static struct clocksource clksrc = {
.name = "tcb_clksrc",
.rating = 200,
#endif
+static void __init tcb_setup_dual_chan(struct atmel_tc *tc, int mck_divisor_idx)
+{
+ /* channel 0: waveform mode, input mclk/8, clock TIOA0 on overflow */
+ __raw_writel(mck_divisor_idx /* likely divide-by-8 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP /* free-run */
+ | ATMEL_TC_ACPA_SET /* TIOA0 rises at 0 */
+ | ATMEL_TC_ACPC_CLEAR, /* (duty cycle 50%) */
+ tcaddr + ATMEL_TC_REG(0, CMR));
+ __raw_writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA));
+ __raw_writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
+
+ /* channel 1: waveform mode, input TIOA0 */
+ __raw_writel(ATMEL_TC_XC1 /* input: TIOA0 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP, /* free-run */
+ tcaddr + ATMEL_TC_REG(1, CMR));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR));
+
+ /* chain channel 0 to channel 1*/
+ __raw_writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR);
+ /* then reset all the timers */
+ __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+}
+
+static void __init tcb_setup_single_chan(struct atmel_tc *tc, int mck_divisor_idx)
+{
+ /* channel 0: waveform mode, input mclk/8 */
+ __raw_writel(mck_divisor_idx /* likely divide-by-8 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP, /* free-run */
+ tcaddr + ATMEL_TC_REG(0, CMR));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
+
+ /* then reset all the timers */
+ __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+}
+
static int __init tcb_clksrc_init(void)
{
static char bootinfo[] __initdata
divided_rate / 1000000,
((divided_rate + 500000) % 1000000) / 1000);
- /* tclib will give us three clocks no matter what the
- * underlying platform supports.
- */
- clk_enable(tc->clk[1]);
-
- /* channel 0: waveform mode, input mclk/8, clock TIOA0 on overflow */
- __raw_writel(best_divisor_idx /* likely divide-by-8 */
- | ATMEL_TC_WAVE
- | ATMEL_TC_WAVESEL_UP /* free-run */
- | ATMEL_TC_ACPA_SET /* TIOA0 rises at 0 */
- | ATMEL_TC_ACPC_CLEAR, /* (duty cycle 50%) */
- tcaddr + ATMEL_TC_REG(0, CMR));
- __raw_writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA));
- __raw_writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC));
- __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */
- __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
-
- /* channel 1: waveform mode, input TIOA0 */
- __raw_writel(ATMEL_TC_XC1 /* input: TIOA0 */
- | ATMEL_TC_WAVE
- | ATMEL_TC_WAVESEL_UP, /* free-run */
- tcaddr + ATMEL_TC_REG(1, CMR));
- __raw_writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR)); /* no irqs */
- __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR));
-
- /* chain channel 0 to channel 1, then reset all the timers */
- __raw_writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR);
- __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+ if (tc->tcb_config && tc->tcb_config->counter_width == 32) {
+ /* use apropriate function to read 32 bit counter */
+ clksrc.read = tc_get_cycles32;
+ /* setup ony channel 0 */
+ tcb_setup_single_chan(tc, best_divisor_idx);
+ } else {
+ /* tclib will give us three clocks no matter what the
+ * underlying platform supports.
+ */
+ clk_enable(tc->clk[1]);
+ /* setup both channel 0 & 1 */
+ tcb_setup_dual_chan(tc, best_divisor_idx);
+ }
/* and away we go! */
clocksource_register_hz(&clksrc, divided_rate);
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/i2c-pxa.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/of_i2c.h>
#include <linux/platform_device.h>
#include <linux/err.h>
.functionality = i2c_pxa_functionality,
};
-static int i2c_pxa_probe(struct platform_device *dev)
+static struct of_device_id i2c_pxa_dt_ids[] = {
+ { .compatible = "mrvl,pxa-i2c", .data = (void *)REGS_PXA2XX },
+ { .compatible = "mrvl,pwri2c", .data = (void *)REGS_PXA3XX },
+ { .compatible = "mrvl,mmp-twsi", .data = (void *)REGS_PXA2XX },
+ {}
+};
+MODULE_DEVICE_TABLE(of, i2c_pxa_dt_ids);
+
+static int i2c_pxa_probe_dt(struct platform_device *pdev, struct pxa_i2c *i2c,
+ enum pxa_i2c_types *i2c_types)
{
- struct pxa_i2c *i2c;
- struct resource *res;
- struct i2c_pxa_platform_data *plat = dev->dev.platform_data;
- const struct platform_device_id *id = platform_get_device_id(dev);
- enum pxa_i2c_types i2c_type = id->driver_data;
+ struct device_node *np = pdev->dev.of_node;
+ const struct of_device_id *of_id =
+ of_match_device(i2c_pxa_dt_ids, &pdev->dev);
int ret;
- int irq;
- res = platform_get_resource(dev, IORESOURCE_MEM, 0);
- irq = platform_get_irq(dev, 0);
- if (res == NULL || irq < 0)
- return -ENODEV;
+ if (!of_id)
+ return 1;
+ ret = of_alias_get_id(np, "i2c");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
+ return ret;
+ }
+ pdev->id = ret;
+ if (of_get_property(np, "mrvl,i2c-polling", NULL))
+ i2c->use_pio = 1;
+ if (of_get_property(np, "mrvl,i2c-fast-mode", NULL))
+ i2c->fast_mode = 1;
+ *i2c_types = (u32)(of_id->data);
+ return 0;
+}
- if (!request_mem_region(res->start, resource_size(res), res->name))
- return -ENOMEM;
+static int i2c_pxa_probe_pdata(struct platform_device *pdev,
+ struct pxa_i2c *i2c,
+ enum pxa_i2c_types *i2c_types)
+{
+ struct i2c_pxa_platform_data *plat = pdev->dev.platform_data;
+ const struct platform_device_id *id = platform_get_device_id(pdev);
+
+ *i2c_types = id->driver_data;
+ if (plat) {
+ i2c->use_pio = plat->use_pio;
+ i2c->fast_mode = plat->fast_mode;
+ }
+ return 0;
+}
+
+static int i2c_pxa_probe(struct platform_device *dev)
+{
+ struct i2c_pxa_platform_data *plat = dev->dev.platform_data;
+ enum pxa_i2c_types i2c_type;
+ struct pxa_i2c *i2c;
+ struct resource *res = NULL;
+ int ret, irq;
i2c = kzalloc(sizeof(struct pxa_i2c), GFP_KERNEL);
if (!i2c) {
goto emalloc;
}
+ ret = i2c_pxa_probe_dt(dev, i2c, &i2c_type);
+ if (ret > 0)
+ ret = i2c_pxa_probe_pdata(dev, i2c, &i2c_type);
+ if (ret < 0)
+ goto eclk;
+
+ res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(dev, 0);
+ if (res == NULL || irq < 0) {
+ ret = -ENODEV;
+ goto eclk;
+ }
+
+ if (!request_mem_region(res->start, resource_size(res), res->name)) {
+ ret = -ENOMEM;
+ goto eclk;
+ }
+
i2c->adap.owner = THIS_MODULE;
i2c->adap.retries = 5;
i2c->slave_addr = I2C_PXA_SLAVE_ADDR;
-#ifdef CONFIG_I2C_PXA_SLAVE
if (plat) {
+#ifdef CONFIG_I2C_PXA_SLAVE
i2c->slave_addr = plat->slave_addr;
i2c->slave = plat->slave;
- }
#endif
-
- clk_enable(i2c->clk);
-
- if (plat) {
i2c->adap.class = plat->class;
- i2c->use_pio = plat->use_pio;
- i2c->fast_mode = plat->fast_mode;
}
+ clk_enable(i2c->clk);
+
if (i2c->use_pio) {
i2c->adap.algo = &i2c_pxa_pio_algorithm;
} else {
.name = "pxa2xx-i2c",
.owner = THIS_MODULE,
.pm = I2C_PXA_DEV_PM_OPS,
+ .of_match_table = i2c_pxa_dt_ids,
},
.id_table = i2c_pxa_id_table,
};
#include <linux/ioport.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
+#include <linux/module.h>
#include <linux/slab.h>
#include <linux/export.h>
-
-/* Number of bytes to reserve for the iomem resource */
-#define ATMEL_TC_IOMEM_SIZE 256
-
+#include <linux/of.h>
/*
* This is a thin library to solve the problem of how to portably allocate
struct atmel_tc *tc;
struct platform_device *pdev = NULL;
struct resource *r;
+ size_t size;
spin_lock(&tc_list_lock);
list_for_each_entry(tc, &tc_list, node) {
- if (tc->pdev->id == block) {
+ if (tc->pdev->dev.of_node) {
+ if (of_alias_get_id(tc->pdev->dev.of_node, "tcb")
+ == block) {
+ pdev = tc->pdev;
+ break;
+ }
+ } else if (tc->pdev->id == block) {
pdev = tc->pdev;
break;
}
goto fail;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- r = request_mem_region(r->start, ATMEL_TC_IOMEM_SIZE, name);
if (!r)
goto fail;
- tc->regs = ioremap(r->start, ATMEL_TC_IOMEM_SIZE);
+ size = resource_size(r);
+ r = request_mem_region(r->start, size, name);
+ if (!r)
+ goto fail;
+
+ tc->regs = ioremap(r->start, size);
if (!tc->regs)
goto fail_ioremap;
return tc;
fail_ioremap:
- release_mem_region(r->start, ATMEL_TC_IOMEM_SIZE);
+ release_mem_region(r->start, size);
fail:
tc = NULL;
goto out;
spin_lock(&tc_list_lock);
if (tc->regs) {
iounmap(tc->regs);
- release_mem_region(tc->iomem->start, ATMEL_TC_IOMEM_SIZE);
+ release_mem_region(tc->iomem->start, resource_size(tc->iomem));
tc->regs = NULL;
tc->iomem = NULL;
}
}
EXPORT_SYMBOL_GPL(atmel_tc_free);
+#if defined(CONFIG_OF)
+static struct atmel_tcb_config tcb_rm9200_config = {
+ .counter_width = 16,
+};
+
+static struct atmel_tcb_config tcb_sam9x5_config = {
+ .counter_width = 32,
+};
+
+static const struct of_device_id atmel_tcb_dt_ids[] = {
+ {
+ .compatible = "atmel,at91rm9200-tcb",
+ .data = &tcb_rm9200_config,
+ }, {
+ .compatible = "atmel,at91sam9x5-tcb",
+ .data = &tcb_sam9x5_config,
+ }, {
+ /* sentinel */
+ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_tcb_dt_ids);
+#endif
+
static int __init tc_probe(struct platform_device *pdev)
{
struct atmel_tc *tc;
return -EINVAL;
}
+ /* Now take SoC information if available */
+ if (pdev->dev.of_node) {
+ const struct of_device_id *match;
+ match = of_match_node(atmel_tcb_dt_ids, pdev->dev.of_node);
+ if (match)
+ tc->tcb_config = match->data;
+ }
+
tc->clk[0] = clk;
tc->clk[1] = clk_get(&pdev->dev, "t1_clk");
if (IS_ERR(tc->clk[1]))
}
static struct platform_driver tc_driver = {
- .driver.name = "atmel_tcb",
+ .driver = {
+ .name = "atmel_tcb",
+ .of_match_table = of_match_ptr(atmel_tcb_dt_ids),
+ },
};
static int __init tc_init(void)
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
/*
/*
* Use 16 bit accesses unless/until we need 8-bit i/o space.
*/
- csr = at91_sys_read(AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
+ csr = at91_ramc_read(0, AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
/*
* NOTE: this CF controller ignores IOIS16, so we can't really do
csr |= AT91_SMC_DBW_16;
pr_debug("%s: 16bit i/o bus\n", driver_name);
}
- at91_sys_write(AT91_SMC_CSR(cf->board->chipselect), csr);
+ at91_ramc_write(0, AT91_SMC_CSR(cf->board->chipselect), csr);
io->start = cf->socket.io_offset;
io->stop = io->start + SZ_2K - 1;
void __iomem *rtt;
struct rtc_device *rtcdev;
u32 imr;
+ void __iomem *gpbr;
};
#define rtt_readl(rtc, field) \
__raw_writel((val), (rtc)->rtt + AT91_RTT_ ## field)
#define gpbr_readl(rtc) \
- at91_sys_read(AT91_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR)
+ __raw_readl((rtc)->gpbr)
#define gpbr_writel(rtc, val) \
- at91_sys_write(AT91_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR, (val))
+ __raw_writel((val), (rtc)->gpbr)
/*
* Read current time and date in RTC
/*
* Initialize and install RTC driver
*/
-static int __init at91_rtc_probe(struct platform_device *pdev)
+static int __devinit at91_rtc_probe(struct platform_device *pdev)
{
- struct resource *r;
+ struct resource *r, *r_gpbr;
struct sam9_rtc *rtc;
int ret;
u32 mr;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!r)
+ r_gpbr = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!r || !r_gpbr) {
+ dev_err(&pdev->dev, "need 2 ressources\n");
return -ENODEV;
+ }
rtc = kzalloc(sizeof *rtc, GFP_KERNEL);
if (!rtc)
goto fail;
}
+ rtc->gpbr = ioremap(r_gpbr->start, resource_size(r_gpbr));
+ if (!rtc->gpbr) {
+ dev_err(&pdev->dev, "failed to map gpbr registers, aborting.\n");
+ ret = -ENOMEM;
+ goto fail_gpbr;
+ }
+
mr = rtt_readl(rtc, MR);
/* unless RTT is counting at 1 Hz, re-initialize it */
if (ret) {
dev_dbg(&pdev->dev, "can't share IRQ %d?\n", AT91_ID_SYS);
rtc_device_unregister(rtc->rtcdev);
- goto fail;
+ goto fail_register;
}
/* NOTE: sam9260 rev A silicon has a ROM bug which resets the
return 0;
fail_register:
+ iounmap(rtc->gpbr);
+fail_gpbr:
iounmap(rtc->rtt);
fail:
platform_set_drvdata(pdev, NULL);
/*
* Disable and remove the RTC driver
*/
-static int __exit at91_rtc_remove(struct platform_device *pdev)
+static int __devexit at91_rtc_remove(struct platform_device *pdev)
{
struct sam9_rtc *rtc = platform_get_drvdata(pdev);
u32 mr = rtt_readl(rtc, MR);
rtc_device_unregister(rtc->rtcdev);
+ iounmap(rtc->gpbr);
iounmap(rtc->rtt);
platform_set_drvdata(pdev, NULL);
kfree(rtc);
#endif
static struct platform_driver at91_rtc_driver = {
- .driver.name = "rtc-at91sam9",
- .driver.owner = THIS_MODULE,
- .remove = __exit_p(at91_rtc_remove),
+ .probe = at91_rtc_probe,
+ .remove = __devexit_p(at91_rtc_remove),
.shutdown = at91_rtc_shutdown,
.suspend = at91_rtc_suspend,
.resume = at91_rtc_resume,
+ .driver = {
+ .name = "rtc-at91sam9",
+ .owner = THIS_MODULE,
+ },
};
-/* Chips can have more than one RTT module, and they can be used for more
- * than just RTCs. So we can't just register as "the" RTT driver.
- *
- * A normal approach in such cases is to create a library to allocate and
- * free the modules. Here we just use bus_find_device() as like such a
- * library, binding directly ... no runtime "library" footprint is needed.
- */
-static int __init at91_rtc_match(struct device *dev, void *v)
-{
- struct platform_device *pdev = to_platform_device(dev);
- int ret;
-
- /* continue searching if this isn't the RTT we need */
- if (strcmp("at91_rtt", pdev->name) != 0
- || pdev->id != CONFIG_RTC_DRV_AT91SAM9_RTT)
- goto fail;
-
- /* else we found it ... but fail unless we can bind to the RTC driver */
- if (dev->driver) {
- dev_dbg(dev, "busy, can't use as RTC!\n");
- goto fail;
- }
- dev->driver = &at91_rtc_driver.driver;
- if (device_attach(dev) == 0) {
- dev_dbg(dev, "can't attach RTC!\n");
- goto fail;
- }
- ret = at91_rtc_probe(pdev);
- if (ret == 0)
- return true;
-
- dev_dbg(dev, "RTC probe err %d!\n", ret);
-fail:
- return false;
-}
-
static int __init at91_rtc_init(void)
{
- int status;
- struct device *rtc;
-
- status = platform_driver_register(&at91_rtc_driver);
- if (status)
- return status;
- rtc = bus_find_device(&platform_bus_type, NULL,
- NULL, at91_rtc_match);
- if (!rtc)
- platform_driver_unregister(&at91_rtc_driver);
- return rtc ? 0 : -ENODEV;
+ return platform_driver_register(&at91_rtc_driver);
}
module_init(at91_rtc_init);
atmel_pops.set_wake = fns->set_wake;
}
+struct platform_device *atmel_default_console_device; /* the serial console device */
+
#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
static void atmel_console_putchar(struct uart_port *port, int ch)
{
#include <linux/circ_buf.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/io.h>
#include <linux/slab.h>
+#define PXA_NAME_LEN 8
+
struct uart_pxa_port {
struct uart_port port;
unsigned char ier;
unsigned char mcr;
unsigned int lsr_break_flag;
struct clk *clk;
- char *name;
+ char name[PXA_NAME_LEN];
};
static inline unsigned int serial_in(struct uart_pxa_port *up, int offset)
};
#endif
+static struct of_device_id serial_pxa_dt_ids[] = {
+ { .compatible = "mrvl,pxa-uart", },
+ { .compatible = "mrvl,mmp-uart", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, serial_pxa_dt_ids);
+
+static int serial_pxa_probe_dt(struct platform_device *pdev,
+ struct uart_pxa_port *sport)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+
+ if (!np)
+ return 1;
+
+ ret = of_alias_get_id(np, "serial");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
+ return ret;
+ }
+ sport->port.line = ret;
+ return 0;
+}
+
static int serial_pxa_probe(struct platform_device *dev)
{
struct uart_pxa_port *sport;
sport->port.irq = irqres->start;
sport->port.fifosize = 64;
sport->port.ops = &serial_pxa_pops;
- sport->port.line = dev->id;
sport->port.dev = &dev->dev;
sport->port.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
sport->port.uartclk = clk_get_rate(sport->clk);
- switch (dev->id) {
- case 0: sport->name = "FFUART"; break;
- case 1: sport->name = "BTUART"; break;
- case 2: sport->name = "STUART"; break;
- case 3: sport->name = "HWUART"; break;
- default:
- sport->name = "???";
- break;
- }
+ ret = serial_pxa_probe_dt(dev, sport);
+ if (ret > 0)
+ sport->port.line = dev->id;
+ else if (ret < 0)
+ goto err_clk;
+ snprintf(sport->name, PXA_NAME_LEN - 1, "UART%d", sport->port.line + 1);
sport->port.membase = ioremap(mmres->start, resource_size(mmres));
if (!sport->port.membase) {
goto err_clk;
}
- serial_pxa_ports[dev->id] = sport;
+ serial_pxa_ports[sport->port.line] = sport;
uart_add_one_port(&serial_pxa_reg, &sport->port);
platform_set_drvdata(dev, sport);
#ifdef CONFIG_PM
.pm = &serial_pxa_pm_ops,
#endif
+ .of_match_table = serial_pxa_dt_ids,
},
};
#include <mach/board.h>
#include <mach/cpu.h>
#include <mach/at91sam9261_matrix.h>
+#include <mach/at91_matrix.h>
#include "at91_udc.h"
} else if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()) {
u32 usbpucr;
- usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR);
+ usbpucr = at91_matrix_read(AT91_MATRIX_USBPUCR);
usbpucr |= AT91_MATRIX_USBPUCR_PUON;
- at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr);
+ at91_matrix_write(AT91_MATRIX_USBPUCR, usbpucr);
}
} else {
stop_activity(udc);
} else if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()) {
u32 usbpucr;
- usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR);
+ usbpucr = at91_matrix_read(AT91_MATRIX_USBPUCR);
usbpucr &= ~AT91_MATRIX_USBPUCR_PUON;
- at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr);
+ at91_matrix_write(AT91_MATRIX_USBPUCR, usbpucr);
}
clk_off(udc);
}
static void toggle_bias(int is_on)
{
- unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
+ unsigned int uckr = at91_pmc_read(AT91_CKGR_UCKR);
if (is_on)
- at91_sys_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN);
+ at91_pmc_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN);
else
- at91_sys_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN));
+ at91_pmc_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN));
}
#else
/* From the GPIO notifying the over-current situation, find
* out the corresponding port */
- gpio = irq_to_gpio(irq);
for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) {
- if (pdata->overcurrent_pin[port] == gpio)
+ if (gpio_to_irq(pdata->overcurrent_pin[port]) == irq) {
+ gpio = pdata->overcurrent_pin[port];
break;
+ }
}
if (port == ARRAY_SIZE(pdata->overcurrent_pin)) {
*/
static inline void at91_wdt_stop(void)
{
- at91_sys_write(AT91_ST_WDMR, AT91_ST_EXTEN);
+ at91_st_write(AT91_ST_WDMR, AT91_ST_EXTEN);
}
/*
*/
static inline void at91_wdt_start(void)
{
- at91_sys_write(AT91_ST_WDMR, AT91_ST_EXTEN | AT91_ST_RSTEN |
+ at91_st_write(AT91_ST_WDMR, AT91_ST_EXTEN | AT91_ST_RSTEN |
(((65536 * wdt_time) >> 8) & AT91_ST_WDV));
- at91_sys_write(AT91_ST_CR, AT91_ST_WDRST);
+ at91_st_write(AT91_ST_CR, AT91_ST_WDRST);
}
/*
*/
static inline void at91_wdt_reload(void)
{
- at91_sys_write(AT91_ST_CR, AT91_ST_WDRST);
+ at91_st_write(AT91_ST_CR, AT91_ST_WDRST);
}
/* ......................................................................... */
struct clk;
/**
+ * struct atmel_tcb_config - SoC data for a Timer/Counter Block
+ * @counter_width: size in bits of a timer counter register
+ */
+struct atmel_tcb_config {
+ size_t counter_width;
+};
+
+/**
* struct atmel_tc - information about a Timer/Counter Block
* @pdev: physical device
* @iomem: resource associated with the I/O register
* @regs: mapping through which the I/O registers can be accessed
+ * @tcb_config: configuration data from SoC
* @irq: irq for each of the three channels
* @clk: internal clock source for each of the three channels
* @node: list node, for tclib internal use
struct platform_device *pdev;
struct resource *iomem;
void __iomem *regs;
+ struct atmel_tcb_config *tcb_config;
int irq[3];
struct clk *clk[3];
struct list_head node;
projects / profile / ivi / kernel-adaptation-intel-automotive.git / commitdiff