Changes since U-Boot 1.1.1:
======================================================================
+* Patch by Yuli Barcohen, 13 Jul 2004:
+ Allow clock setting on MPC866/MPC885 series chips according to
+ environment variable `cpuclk'
+
+* Patch by Yuli Barcohen, 20 Apr 2004:
+ Remove unnecessary redefine of CPM_DATAONLY_SIZE for MPC826x
+
* Patch by Vincent Dubey, 24 Sep 2004:
Add support for xaeniax board
CONFIG_MPC8240, CONFIG_MPC8245
- 8xx CPU Options: (if using an MPC8xx cpu)
- Define one or more of
- CONFIG_8xx_GCLK_FREQ - if get_gclk_freq() cannot work
+ CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
+ get_gclk_freq() cannot work
e.g. if there is no 32KHz
reference PIT/RTC clock
+ CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
+ or XTAL/EXTAL)
-- 859/866 CPU options: (if using a MPC859 or MPC866 CPU):
- CFG_866_OSCCLK
- CFG_866_CPUCLK_MIN
- CFG_866_CPUCLK_MAX
- CFG_866_CPUCLK_DEFAULT
+- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
+ CFG_8xx_CPUCLK_MIN
+ CFG_8xx_CPUCLK_MAX
+ CONFIG_8xx_CPUCLK_DEFAULT
See doc/README.MPC866
CFG_MEASURE_CPUCLK
values. Mostly useful for board bringup to make sure
the PLL is locked at the intended frequency. Note
that this requires a (stable) reference clock (32 kHz
- RTC clock),
+ RTC clock or CFG_8XX_XIN)
- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
#include <common.h>
#include <asm/cpm_8260.h>
-/*
- * because we have stack and init data in dual port ram
- * we must reduce the size
- */
-#undef CPM_DATAONLY_SIZE
-#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE)
-
void
m8260_cpm_reset(void)
{
printf ("unknown M%s (0x%08x)", id_str, k);
-#if defined(CFG_866_CPUCLK_MIN) && defined(CFG_866_CPUCLK_MAX)
+#if defined(CFG_8xx_CPUCLK_MIN) && defined(CFG_8xx_CPUCLK_MAX)
printf (" at %s MHz [%d.%d...%d.%d MHz]\n ",
strmhz (buf, clock),
- CFG_866_CPUCLK_MIN / 1000000,
- ((CFG_866_CPUCLK_MIN % 1000000) + 50000) / 100000,
- CFG_866_CPUCLK_MAX / 1000000,
- ((CFG_866_CPUCLK_MAX % 1000000) + 50000) / 100000
+ CFG_8xx_CPUCLK_MIN / 1000000,
+ ((CFG_8xx_CPUCLK_MIN % 1000000) + 50000) / 100000,
+ CFG_8xx_CPUCLK_MAX / 1000000,
+ ((CFG_8xx_CPUCLK_MAX % 1000000) + 50000) / 100000
);
#else
printf (" at %s MHz: ", strmhz (buf, clock));
checkdcache () >> 10
);
- /* do we have a FEC (860T/P or 852/859/866)? */
+ /* do we have a FEC (860T/P or 852/859/866/885)? */
immap->im_cpm.cp_fec.fec_addr_low = 0x12345678;
if (immap->im_cpm.cp_fec.fec_addr_low == 0x12345678) {
#include <mpc8xx.h>
#include <asm/processor.h>
-#if !defined(CONFIG_TQM866M) || defined(CFG_MEASURE_CPUCLK)
+#if !defined(CONFIG_8xx_CPUCLK_DEFAULT) || defined(CFG_MEASURE_CPUCLK)
#define PITC_SHIFT 16
#define PITR_SHIFT 16
#endif
-#if !defined(CONFIG_TQM866M) && !defined(CONFIG_NC650)
+#if !defined(CONFIG_8xx_CPUCLK_DEFAULT)
/*
* get_clocks() fills in gd->cpu_clock depending on CONFIG_8xx_GCLK_FREQ
return (0);
}
-#else /* CONFIG_MPC866_FAMILY */
+#else /* CONFIG_8xx_CPUCLK_DEFAULT defined, use dynamic clock setting */
static long init_pll_866 (long clk);
/* This function sets up PLL (init_pll_866() is called) and
* fills gd->cpu_clk and gd->bus_clk according to the environment
- * variable 'cpuclk' or to CFG_866_CPUCLK_DEFAULT (if 'cpuclk'
+ * variable 'cpuclk' or to CONFIG_8xx_CPUCLK_DEFAULT (if 'cpuclk'
* contains invalid value).
- * This functions requires an MPC866 series CPU.
+ * This functions requires an MPC866 or newer series CPU.
*/
int get_clocks_866 (void)
{
if (getenv_r ("cpuclk", tmp, sizeof (tmp)) > 0)
cpuclk = simple_strtoul (tmp, NULL, 10) * 1000000;
- if ((CFG_866_CPUCLK_MIN > cpuclk) || (CFG_866_CPUCLK_MAX < cpuclk))
- cpuclk = CFG_866_CPUCLK_DEFAULT;
+ if ((CFG_8xx_CPUCLK_MIN > cpuclk) || (CFG_8xx_CPUCLK_MAX < cpuclk))
+ cpuclk = CONFIG_8xx_CPUCLK_DEFAULT;
gd->cpu_clk = init_pll_866 (cpuclk);
#if defined(CFG_MEASURE_CPUCLK)
mamr = immr->im_memctl.memc_mamr;
mamr &= ~MAMR_PTA_MSK;
- mamr |= ((gd->cpu_clk / CFG_866_PTA_PER_CLK) << MAMR_PTA_SHIFT);
+ mamr |= ((gd->cpu_clk / CFG_PTA_PER_CLK) << MAMR_PTA_SHIFT);
immr->im_memctl.memc_mamr = mamr;
return (0);
}
-/* Configure PLL for MPC866/859 CPU series
+/* Configure PLL for MPC866/859/885 CPU series
* PLL multiplication factor is set to the value nearest to the desired clk,
* assuming a oscclk of 10 MHz.
*/
if (clk < 40000000) {
s = 2;
- step_mfi = CFG_866_OSCCLK / 4;
+ step_mfi = CONFIG_8xx_OSCLK / 4;
mfd = 7;
- step_mfn = CFG_866_OSCCLK / 30;
+ step_mfn = CONFIG_8xx_OSCLK / 30;
} else if (clk < 80000000) {
s = 1;
- step_mfi = CFG_866_OSCCLK / 2;
+ step_mfi = CONFIG_8xx_OSCLK / 2;
mfd = 14;
- step_mfn = CFG_866_OSCCLK / 30;
+ step_mfn = CONFIG_8xx_OSCLK / 30;
} else {
s = 0;
- step_mfi = CFG_866_OSCCLK;
+ step_mfi = CONFIG_8xx_OSCLK;
mfd = 29;
- step_mfn = CFG_866_OSCCLK / 30;
+ step_mfn = CONFIG_8xx_OSCLK / 30;
}
/* Calculate integer part of multiplication factor
return (n);
}
-#endif /* CONFIG_MPC866_FAMILY */
+#endif /* CONFIG_8xx_CPUCLK_DEFAULT */
#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M)
/*
The current implementation allows the user to specify the desired CPU
clock value, in MHz, via an environment variable "cpuclk".
-Three compile-time constants are used:
+Four compile-time constants are used:
- CFG_866_OSCCLK - input quartz clock
- CFG_866_CPUCLK_MIN - minimum allowed CPU clock
- CFG_866_CPUCLK_MAX - maximum allowed CPU clock
- CFG_866_CPUCLK_DEFAULT - default CPU clock value
+ CONFIG_8xx_OSCLK - input quartz clock
+ CFG_8xx_CPUCLK_MIN - minimum allowed CPU clock
+ CFG_8xx_CPUCLK_MAX - maximum allowed CPU clock
+ CONFIG_8xx_CPUCLK_DEFAULT - default CPU clock value
If the "cpuclk" environment variable value is within the CPUCLK_MIN /
CPUCLK_MAX limits, the specified value is used. Otherwise, the
the restrictions of your hardware (board, processor). For example,
ethernet will stop working for CPU clock frequencies below 25 MHz.
-Please note that for now the new clock-handling code has been enabled
-for the TQM866M board only, even though it should be pretty much
-common for other MPC859 / MPC866 based boards also. Our intention
-here was to move in small steps and not to break the existing code
-for other boards.
+Please note that the new clock-handling code is enabled if
+CONFIG_8xx_CPUCLK_DEFAULT is defined. Since this mechanism supports
+only MPC866 and newer CPUs, this constant MUST NOT be defined for
+MPC823/850/860/862 series. The clock generation algorithm for older
+chips is different and has not been implemented yet. If you need it,
+your patch is welcome.
#define FEC_ENET
#endif /* CONFIG_FEC_ENET */
-#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz oscillator on EXTCLK */
+#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz oscillator on EXTCLK */
+#define CONFIG_8xx_CPUCLK_DEFAULT 50000000
+#define CFG_8xx_CPUCLK_MIN 40000000
+#ifdef CONFIG_MPC852T
+#define CFG_8xx_CPUCLK_MAX 50000000
+#else
+#define CFG_8xx_CPUCLK_MAX 120000000
+#endif /* CONFIG_MPC852T */
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
| CFG_CMD_DHCP \
#define CFG_MAMR 0x00802114
+/*
+ * 2048 SDRAM rows
+ * 1000 factor s -> ms
+ * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4 Number of refresh cycles per period
+ * 64 Refresh cycle in ms per number of rows
+ */
+#define CFG_PTA_PER_CLK ((2048 * 64 * 1000) / (4 * 64))
+
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x00700000 /* 1 ... 7 MB in SDRAM */
/*
* 10 MHz - PLL input clock
*/
-#define CFG_866_OSCCLK 10000000
+#define CFG_8xx_OSCCLK 10000000
/*
* 50 MHz - default CPU clock
*/
-#define CFG_866_CPUCLK_DEFAULT 50000000
+#define CONFIG_8xx_CPUCLK_DEFAULT 50000000
/*
* 15 MHz - CPU minimum clock
*/
-#define CFG_866_CPUCLK_MIN 15000000
+#define CFG_8xx_CPUCLK_MIN 15000000
/*
* 133 MHz - CPU maximum clock
*/
-#define CFG_866_CPUCLK_MAX 133000000
+#define CFG_8xx_CPUCLK_MAX 133000000
#define CFG_MEASURE_CPUCLK
-#define CFG_8XX_XIN CFG_866_OSCCLK
+#define CFG_8XX_XIN CFG_8xx_OSCCLK
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
* 4 Number of refresh cycles per period
* 64 Refresh cycle in ms per number of rows
*/
-#define CFG_866_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
+#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
/*
* Memory Periodic Timer Prescaler
/*
- * (C) Copyright 2000-2003
+ * (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_MPC866 1 /* This is a MPC866 CPU */
#define CONFIG_TQM866M 1 /* ...on a TQM8xxM module */
-#define CFG_866_OSCCLK 10000000 /* 10 MHz - PLL input clock */
-#define CFG_866_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */
-#define CFG_866_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */
-#define CFG_866_CPUCLK_DEFAULT 50000000 /* 50 MHz - CPU default clock */
+#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz - PLL input clock */
+#define CFG_8xx_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */
+#define CFG_8xx_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */
+#define CONFIG_8xx_CPUCLK_DEFAULT 50000000 /* 50 MHz - CPU default clock */
/* (it will be used if there is no */
/* 'cpuclk' variable with valid value) */
* 4 Number of refresh cycles per period
* 64 Refresh cycle in ms per number of rows
*/
-#define CFG_866_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
+#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
/*
* Memory Periodic Timer Prescaler
* Periodic timer for refresh, start with refresh rate for 40 MHz clock
- * (CFG_866_CPUCLK_MIN / CFG_866_PTA_PER_CLK)
+ * (CFG_8xx_CPUCLK_MIN / CFG_PTA_PER_CLK)
*/
#define CFG_MAMR_PTA 39
board_early_init_f,
#endif
-#if !defined(CONFIG_TQM866M) && !defined(CONFIG_NC650)
+#if !defined(CONFIG_8xx_CPUCLK_DEFAULT)
get_clocks, /* get CPU and bus clocks (etc.) */
#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M)
adjust_sdram_tbs_8xx,
board_postclk_init,
#endif
env_init,
-#if defined(CONFIG_TQM866M) || defined(CONFIG_NC650)
+#if defined(CONFIG_8xx_CPUCLK_DEFAULT)
get_clocks_866, /* get CPU and bus clocks according to the environment variable */
sdram_adjust_866, /* adjust sdram refresh rate according to the new clock */
init_timebase,
projects / platform / kernel / u-boot.git / commitdiff