- clocks: phandle of the core clock which drives the mdio block.
Additional information regarding generic multiplexer properties can be found
-at- Documentation/devicetree/bindings/net/mdio-mux.txt
+at- Documentation/devicetree/bindings/net/mdio-mux.yaml
for example:
+++ /dev/null
-Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
-
-This is a special case of a MDIO bus multiplexer. One or more GPIO
-lines are used to control which child bus is connected.
-
-Required properties in addition to the generic multiplexer properties:
-
-- compatible : mdio-mux-gpio.
-- gpios : GPIO specifiers for each GPIO line. One or more must be specified.
-
-
-Example :
-
- /* The parent MDIO bus. */
- smi1: mdio@1180000001900 {
- compatible = "cavium,octeon-3860-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x11800 0x00001900 0x0 0x40>;
- };
-
- /*
- An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
- pair of GPIO lines. Child busses 2 and 3 populated with 4
- PHYs each.
- */
- mdio-mux {
- compatible = "mdio-mux-gpio";
- gpios = <&gpio1 3 0>, <&gpio1 4 0>;
- mdio-parent-bus = <&smi1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio@2 {
- reg = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy11: ethernet-phy@1 {
- reg = <1>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <10 8>; /* Pin 10, active low */
- };
- phy12: ethernet-phy@2 {
- reg = <2>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <10 8>; /* Pin 10, active low */
- };
- phy13: ethernet-phy@3 {
- reg = <3>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <10 8>; /* Pin 10, active low */
- };
- phy14: ethernet-phy@4 {
- reg = <4>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <10 8>; /* Pin 10, active low */
- };
- };
-
- mdio@3 {
- reg = <3>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy21: ethernet-phy@1 {
- reg = <1>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <12 8>; /* Pin 12, active low */
- };
- phy22: ethernet-phy@2 {
- reg = <2>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <12 8>; /* Pin 12, active low */
- };
- phy23: ethernet-phy@3 {
- reg = <3>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <12 8>; /* Pin 12, active low */
- };
- phy24: ethernet-phy@4 {
- reg = <4>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <12 8>; /* Pin 12, active low */
- };
- };
- };
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mdio-mux-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+
+description:
+ This is a special case of a MDIO bus multiplexer. One or more GPIO
+ lines are used to control which child bus is connected.
+
+allOf:
+ - $ref: /schemas/net/mdio-mux.yaml#
+
+properties:
+ compatible:
+ const: mdio-mux-gpio
+
+ gpios:
+ description:
+ List of GPIOs used to control the multiplexer, least significant bit first.
+ minItems: 1
+ maxItems: 32
+
+required:
+ - compatible
+ - gpios
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ /*
+ An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
+ pair of GPIO lines. Child busses 2 and 3 populated with 4
+ PHYs each.
+ */
+ mdio-mux {
+ compatible = "mdio-mux-gpio";
+ gpios = <&gpio1 3 0>, <&gpio1 4 0>;
+ mdio-parent-bus = <&smi1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-phy@1 {
+ reg = <1>;
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ ethernet-phy@2 {
+ reg = <2>;
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ ethernet-phy@3 {
+ reg = <3>;
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ ethernet-phy@4 {
+ reg = <4>;
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <10 8>; /* Pin 10, active low */
+ };
+ };
+
+ mdio@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-phy@1 {
+ reg = <1>;
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ ethernet-phy@2 {
+ reg = <2>;
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ ethernet-phy@3 {
+ reg = <3>;
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ ethernet-phy@4 {
+ reg = <4>;
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ };
+ };
+...
+++ /dev/null
-Properties for an MDIO bus multiplexer controlled by a memory-mapped device
-
-This is a special case of a MDIO bus multiplexer. A memory-mapped device,
-like an FPGA, is used to control which child bus is connected. The mdio-mux
-node must be a child of the memory-mapped device. The driver currently only
-supports devices with 8, 16 or 32-bit registers.
-
-Required properties in addition to the generic multiplexer properties:
-
-- compatible : string, must contain "mdio-mux-mmioreg"
-
-- reg : integer, contains the offset of the register that controls the bus
- multiplexer. The size field in the 'reg' property is the size of
- register, and must therefore be 1, 2, or 4.
-
-- mux-mask : integer, contains an eight-bit mask that specifies which
- bits in the register control the actual bus multiplexer. The
- 'reg' property of each child mdio-mux node must be constrained by
- this mask.
-
-Example:
-
-The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes.
-For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus.
-A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on
-BRDCFG1 that control the actual mux.
-
- /* The FPGA node */
- fpga: board-control@3,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis";
- reg = <3 0 0x30>;
- ranges = <0 3 0 0x30>;
-
- mdio-mux-emi2 {
- compatible = "mdio-mux-mmioreg", "mdio-mux";
- mdio-parent-bus = <&xmdio0>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <9 1>; // BRDCFG1
- mux-mask = <0x6>; // EMI2
-
- emi2_slot1: mdio@0 { // Slot 1 XAUI (FM2)
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_xgmii_slot1: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c45";
- reg = <4>;
- };
- };
-
- emi2_slot2: mdio@2 { // Slot 2 XAUI (FM1)
- reg = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_xgmii_slot2: ethernet-phy@4 {
- compatible = "ethernet-phy-ieee802.3-c45";
- reg = <0>;
- };
- };
- };
- };
-
- /* The parent MDIO bus. */
- xmdio0: mdio@f1000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,fman-xmdio";
- reg = <0xf1000 0x1000>;
- interrupts = <100 1 0 0>;
- };
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mdio-mux-mmioreg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Properties for an MDIO bus multiplexer controlled by a memory-mapped device
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+
+description: |+
+ This is a special case of a MDIO bus multiplexer. A memory-mapped device,
+ like an FPGA, is used to control which child bus is connected. The mdio-mux
+ node must be a child of the memory-mapped device. The driver currently only
+ supports devices with 8, 16 or 32-bit registers.
+
+allOf:
+ - $ref: /schemas/net/mdio-mux.yaml#
+
+properties:
+ compatible:
+ items:
+ - const: mdio-mux-mmioreg
+ - const: mdio-mux
+
+ reg:
+ description: Contains the offset of the register that controls the bus
+ multiplexer. The size field in the 'reg' property is the size of register,
+ and must therefore be 1, 2, or 4.
+ maxItems: 1
+
+ mux-mask:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Contains an eight-bit mask that specifies which bits in the
+ register control the actual bus multiplexer. The 'reg' property of each
+ child mdio-mux node must be constrained by this mask.
+
+required:
+ - compatible
+ - reg
+ - mux-mask
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ mdio-mux@9 {
+ compatible = "mdio-mux-mmioreg", "mdio-mux";
+ mdio-parent-bus = <&xmdio0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <9 1>; // BRDCFG1
+ mux-mask = <0x6>; // EMI2
+
+ mdio@0 { // Slot 1 XAUI (FM2)
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy_xgmii_slot1: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <4>;
+ };
+ };
+
+ mdio@2 { // Slot 2 XAUI (FM1)
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <4>;
+ };
+ };
+ };
+...
+++ /dev/null
-Properties for an MDIO bus multiplexer consumer device
-
-This is a special case of MDIO mux when MDIO mux is defined as a consumer
-of a mux producer device. The mux producer can be of any type like mmio mux
-producer, gpio mux producer or generic register based mux producer.
-
-Required properties in addition to the MDIO Bus multiplexer properties:
-
-- compatible : should be "mmio-mux-multiplexer"
-- mux-controls : mux controller node to use for operating the mux
-- mdio-parent-bus : phandle to the parent MDIO bus.
-
-each child node of mdio bus multiplexer consumer device represent a mdio
-bus.
-
-for more information please refer
-Documentation/devicetree/bindings/mux/mux-controller.yaml
-and Documentation/devicetree/bindings/net/mdio-mux.txt
-
-Example:
-In below example the Mux producer and consumer are separate nodes.
-
-&i2c0 {
- fpga@66 { // fpga connected to i2c
- compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c",
- "simple-mfd";
- reg = <0x66>;
-
- mux: mux-controller { // Mux Producer
- compatible = "reg-mux";
- #mux-control-cells = <1>;
- mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */
- <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */
- };
- };
-};
-
-mdio-mux-1 { // Mux consumer
- compatible = "mdio-mux-multiplexer";
- mux-controls = <&mux 0>;
- mdio-parent-bus = <&emdio1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio@0 {
- reg = <0x0>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mdio@8 {
- reg = <0x8>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- ..
- ..
-};
-
-mdio-mux-2 { // Mux consumer
- compatible = "mdio-mux-multiplexer";
- mux-controls = <&mux 1>;
- mdio-parent-bus = <&emdio2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio@0 {
- reg = <0x0>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mdio@1 {
- reg = <0x1>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- ..
- ..
-};
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mdio-mux-multiplexer.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Properties for an MDIO bus multiplexer consumer device
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+
+description: |+
+ This is a special case of MDIO mux when MDIO mux is defined as a consumer
+ of a mux producer device. The mux producer can be of any type like mmio mux
+ producer, gpio mux producer or generic register based mux producer.
+
+
+allOf:
+ - $ref: /schemas/net/mdio-mux.yaml#
+
+properties:
+ compatible:
+ const: mdio-mux-multiplexer
+
+ mux-controls:
+ maxItems: 1
+
+required:
+ - compatible
+ - mux-controls
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ mux: mux-controller { // Mux Producer
+ compatible = "reg-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */
+ <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */
+ };
+
+ mdio-mux-1 { // Mux consumer
+ compatible = "mdio-mux-multiplexer";
+ mux-controls = <&mux 0>;
+ mdio-parent-bus = <&emdio1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@0 {
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@8 {
+ reg = <0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ mdio-mux-2 { // Mux consumer
+ compatible = "mdio-mux-multiplexer";
+ mux-controls = <&mux 1>;
+ mdio-parent-bus = <&emdio2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@0 {
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1 {
+ reg = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+...
+++ /dev/null
-Common MDIO bus multiplexer/switch properties.
-
-An MDIO bus multiplexer/switch will have several child busses that are
-numbered uniquely in a device dependent manner. The nodes for an MDIO
-bus multiplexer/switch will have one child node for each child bus.
-
-Required properties:
-- #address-cells = <1>;
-- #size-cells = <0>;
-
-Optional properties:
-- mdio-parent-bus : phandle to the parent MDIO bus.
-
-- Other properties specific to the multiplexer/switch hardware.
-
-Required properties for child nodes:
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg : The sub-bus number.
-
-
-Example :
-
- /* The parent MDIO bus. */
- smi1: mdio@1180000001900 {
- compatible = "cavium,octeon-3860-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x11800 0x00001900 0x0 0x40>;
- };
-
- /*
- An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
- pair of GPIO lines. Child busses 2 and 3 populated with 4
- PHYs each.
- */
- mdio-mux {
- compatible = "mdio-mux-gpio";
- gpios = <&gpio1 3 0>, <&gpio1 4 0>;
- mdio-parent-bus = <&smi1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio@2 {
- reg = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy11: ethernet-phy@1 {
- reg = <1>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <10 8>; /* Pin 10, active low */
- };
- phy12: ethernet-phy@2 {
- reg = <2>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <10 8>; /* Pin 10, active low */
- };
- phy13: ethernet-phy@3 {
- reg = <3>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <10 8>; /* Pin 10, active low */
- };
- phy14: ethernet-phy@4 {
- reg = <4>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <10 8>; /* Pin 10, active low */
- };
- };
-
- mdio@3 {
- reg = <3>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy21: ethernet-phy@1 {
- reg = <1>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <12 8>; /* Pin 12, active low */
- };
- phy22: ethernet-phy@2 {
- reg = <2>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <12 8>; /* Pin 12, active low */
- };
- phy23: ethernet-phy@3 {
- reg = <3>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <12 8>; /* Pin 12, active low */
- };
- phy24: ethernet-phy@4 {
- reg = <4>;
- marvell,reg-init = <3 0x10 0 0x5777>,
- <3 0x11 0 0x00aa>,
- <3 0x12 0 0x4105>,
- <3 0x13 0 0x0a60>;
- interrupt-parent = <&gpio>;
- interrupts = <12 8>; /* Pin 12, active low */
- };
- };
- };
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mdio-mux.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Common MDIO bus multiplexer/switch properties.
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+
+description: |+
+ An MDIO bus multiplexer/switch will have several child busses that are
+ numbered uniquely in a device dependent manner. The nodes for an MDIO
+ bus multiplexer/switch will have one child node for each child bus.
+
+properties:
+ $nodename:
+ pattern: '^mdio-mux[\-@]?'
+
+ mdio-parent-bus:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ The phandle of the MDIO bus that this multiplexer's master-side port is
+ connected to.
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+patternProperties:
+ '^mdio@[0-9a-f]+$':
+ type: object
+
+ properties:
+ reg:
+ maxItems: 1
+ description: The sub-bus number.
+
+additionalProperties: true
+
+...
projects / platform / kernel / linux-starfive.git / commitdiff