ethernet: set RX delay for exphy and leds [1/1]

PD#SWPL-5295

Problem:
add RX delay for 8211f and add led setup interface

Solution:
tuning delay and leds

Verify:
verify on u200 board

Change-Id: I45e855894d570fdd976f90fd8f03151ad52a3683
Signed-off-by: Zhuo Wang <zhuo.wang@amlogic.com>

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c
index d3073cd..9910115 100644 (file)
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c
@@ -34,6 +34,7 @@
 /* if it's internal phy we will shutdown analog*/
 static unsigned int is_internal_phy;
 /* Ethernet register for G12A PHY */
+#define REG_ETH_REG1_OFFSET 0x4
 #define ETH_PLL_CTL0 0x44
 #define ETH_PLL_CTL1 0x48
 #define ETH_PLL_CTL2 0x4C
@@ -227,10 +228,12 @@ static void __iomem *network_interface_setup(struct platform_device *pdev)
        return PREG_ETH_REG0;
 }
 
-static int dwmac_meson_cfg_ctrl(void __iomem *base_addr)
+static int dwmac_meson_cfg_ctrl(void __iomem *base_addr,
+                               struct platform_device *pdev)
 {
        void __iomem *ETH_PHY_config_addr = base_addr;
-
+       unsigned int led_setting = 0;
+       unsigned int phy_setting = 0x54147;
        /*config phyid should between  a 0~0xffffffff*/
        /*please don't use 44000181, this has been used by internal phy*/
        writel(0x33010180, ETH_PHY_config_addr + ETH_PHY_CNTL0);
@@ -238,9 +241,16 @@ static int dwmac_meson_cfg_ctrl(void __iomem *base_addr)
        /*use_phy_smi | use_phy_ip | co_clkin from eth_phy_top*/
        writel(0x260, ETH_PHY_config_addr + ETH_PHY_CNTL2);
        /*led signal is inverted*/
-       writel(0x41054147, ETH_PHY_config_addr + ETH_PHY_CNTL1);
-       writel(0x41014147, ETH_PHY_config_addr + ETH_PHY_CNTL1);
-       writel(0x41054147, ETH_PHY_config_addr + ETH_PHY_CNTL1);
+       if (of_property_read_u32(pdev->dev.of_node,
+                                "led_setting", &led_setting))
+               led_setting = 0x41;
+       else
+               pr_info("load led setting as 0x%x\n", led_setting);
+
+       phy_setting = (led_setting << 24) + (phy_setting & ~(0xff << 24));
+       writel(phy_setting, ETH_PHY_config_addr + ETH_PHY_CNTL1);
+       writel(phy_setting & ~(0x1 << 18), ETH_PHY_config_addr + ETH_PHY_CNTL1);
+       writel(phy_setting, ETH_PHY_config_addr + ETH_PHY_CNTL1);
        /*wait phy to reset cause Power Up Reset need 5.2~2.6 ms*/
        mdelay(10);
        return 0;
@@ -294,6 +304,7 @@ static void __iomem *g12a_network_interface_setup(struct platform_device *pdev)
        struct pinctrl *pin_ctl;
        struct resource *res = NULL;
        u32 mc_val;
+       u32 cali_val;
        void __iomem *addr = NULL;
        void __iomem *REG_ETH_reg0_addr = NULL;
        void __iomem *ETH_PHY_config_addr = NULL;
@@ -357,7 +368,7 @@ static void __iomem *g12a_network_interface_setup(struct platform_device *pdev)
                /*PLL*/
                dwmac_meson_cfg_pll(ETH_PHY_config_addr, pdev);
                dwmac_meson_cfg_analog(ETH_PHY_config_addr, pdev);
-               dwmac_meson_cfg_ctrl(ETH_PHY_config_addr);
+               dwmac_meson_cfg_ctrl(ETH_PHY_config_addr, pdev);
                pin_ctl = devm_pinctrl_get_select
                        (&pdev->dev, "internal_eth_pins");
                return REG_ETH_reg0_addr;
@@ -376,6 +387,13 @@ static void __iomem *g12a_network_interface_setup(struct platform_device *pdev)
 
                /*switch to extern phy*/
                writel(0x0, ETH_PHY_config_addr + ETH_PHY_CNTL2);
+               /*set PRG_ETH_REG1 for exphy delay*/
+               if (of_property_read_u32(np, "cali_val", &cali_val))
+                       pr_info("Not set  cali_val for REG1\n");
+               else
+                       writel(cali_val, REG_ETH_reg0_addr +
+                                       REG_ETH_REG1_OFFSET);
+
                pin_ctl = devm_pinctrl_get_select
                        (&pdev->dev, "external_eth_pins");
                return REG_ETH_reg0_addr;