drm/i915: enable intel_lvds->pre_pll_enable for ilk+, too
authorDaniel Vetter <daniel.vetter@ffwll.ch>
Mon, 26 Nov 2012 16:22:13 +0000 (17:22 +0100)
committerDaniel Vetter <daniel.vetter@ffwll.ch>
Thu, 29 Nov 2012 11:51:37 +0000 (12:51 +0100)
Only two things needed adjustment:
- pipe select for PCH_CPT
- There's no dithering bit on ilk+ in the lvds ctl reg

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_lvds.c

index bb080fb..5958b3b 100644 (file)
@@ -5322,7 +5322,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
        bool ok, has_reduced_clock = false;
        bool is_lvds = false, is_dp = false, is_cpu_edp = false;
        struct intel_encoder *encoder;
-       u32 temp;
        int ret;
        bool dither, fdi_config_ok;
 
@@ -5386,45 +5385,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
        } else
                intel_put_pch_pll(intel_crtc);
 
-       /* The LVDS pin pair needs to be on before the DPLLs are enabled.
-        * This is an exception to the general rule that mode_set doesn't turn
-        * things on.
-        */
-       if (is_lvds) {
-               temp = I915_READ(PCH_LVDS);
-               temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
-               if (HAS_PCH_CPT(dev)) {
-                       temp &= ~PORT_TRANS_SEL_MASK;
-                       temp |= PORT_TRANS_SEL_CPT(pipe);
-               } else {
-                       if (pipe == 1)
-                               temp |= LVDS_PIPEB_SELECT;
-                       else
-                               temp &= ~LVDS_PIPEB_SELECT;
-               }
-
-               /* set the corresponsding LVDS_BORDER bit */
-               temp |= dev_priv->lvds_border_bits;
-               /* Set the B0-B3 data pairs corresponding to whether we're going to
-                * set the DPLLs for dual-channel mode or not.
-                */
-               if (clock.p2 == 7)
-                       temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
-               else
-                       temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
-
-               /* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
-                * appropriately here, but we need to look more thoroughly into how
-                * panels behave in the two modes.
-                */
-               temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
-               if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
-                       temp |= LVDS_HSYNC_POLARITY;
-               if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
-                       temp |= LVDS_VSYNC_POLARITY;
-               I915_WRITE(PCH_LVDS, temp);
-       }
-
        if (is_dp && !is_cpu_edp) {
                intel_dp_set_m_n(crtc, mode, adjusted_mode);
        } else {
index c93ec03..7781069 100644 (file)
@@ -104,17 +104,20 @@ static void intel_pre_pll_enable_lvds(struct intel_encoder *encoder)
        int pipe = intel_crtc->pipe;
        u32 temp;
 
-       /* pch split platforms are not yet converted. */
-       if (HAS_PCH_SPLIT(dev))
-               return;
-
        temp = I915_READ(lvds_encoder->reg);
        temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
-       if (pipe == 1) {
-               temp |= LVDS_PIPEB_SELECT;
+
+       if (HAS_PCH_CPT(dev)) {
+               temp &= ~PORT_TRANS_SEL_MASK;
+               temp |= PORT_TRANS_SEL_CPT(pipe);
        } else {
-               temp &= ~LVDS_PIPEB_SELECT;
+               if (pipe == 1) {
+                       temp |= LVDS_PIPEB_SELECT;
+               } else {
+                       temp &= ~LVDS_PIPEB_SELECT;
+               }
        }
+
        /* set the corresponsding LVDS_BORDER bit */
        temp |= dev_priv->lvds_border_bits;
        /* Set the B0-B3 data pairs corresponding to whether we're going to
@@ -129,8 +132,11 @@ static void intel_pre_pll_enable_lvds(struct intel_encoder *encoder)
         * appropriately here, but we need to look more thoroughly into how
         * panels behave in the two modes.
         */
-       /* set the dithering flag on LVDS as needed */
-       if (INTEL_INFO(dev)->gen >= 4) {
+
+       /* Set the dithering flag on LVDS as needed, note that there is no
+        * special lvds dither control bit on pch-split platforms, dithering is
+        * only controlled through the PIPECONF reg. */
+       if (INTEL_INFO(dev)->gen == 4) {
                if (dev_priv->lvds_dither)
                        temp |= LVDS_ENABLE_DITHER;
                else