* to be saved again on kernel mode stack, as part of pt_regs.
*-------------------------------------------------------------*/
.macro PROLOG_FREEUP_REG reg, mem
-#ifndef ARC_USE_SCRATCH_REG
- sr \reg, [ARC_REG_SCRATCH_DATA0]
-#else
st \reg, [\mem]
-#endif
.endm
.macro PROLOG_RESTORE_REG reg, mem
-#ifndef ARC_USE_SCRATCH_REG
- lr \reg, [ARC_REG_SCRATCH_DATA0]
-#else
ld \reg, [\mem]
-#endif
.endm
/*--------------------------------------------------------------
#define ARC_REG_SCRATCH_DATA0 0x46c
#endif
-#if defined(CONFIG_ISA_ARCV2) || !defined(CONFIG_SMP)
-#define ARC_USE_SCRATCH_REG
-#endif
-
/* Bits in MMU PID register */
#define __TLB_ENABLE (1 << 31)
#define __PROG_ENABLE (1 << 30)
*/
cpumask_set_cpu(cpu, mm_cpumask(next));
-#ifdef ARC_USE_SCRATCH_REG
+#ifdef CONFIG_ISA_ARCV2
/* PGD cached in MMU reg to avoid 3 mem lookups: task->mm->pgd */
write_aux_reg(ARC_REG_SCRATCH_DATA0, next->pgd);
#endif
set_pte(ptep, pteval);
}
-/*
- * Macro to quickly access the PGD entry, utlising the fact that some
- * arch may cache the pointer to Page Directory of "current" task
- * in a MMU register
- *
- * Thus task->mm->pgd (3 pointer dereferences, cache misses etc simply
- * becomes read a register
- *
- * ********CAUTION*******:
- * Kernel code might be dealing with some mm_struct of NON "current"
- * Thus use this macro only when you are certain that "current" is current
- * e.g. when dealing with signal frame setup code etc
- */
-#ifdef ARC_USE_SCRATCH_REG
-#define pgd_offset_fast(mm, addr) \
-({ \
- pgd_t *pgd_base = (pgd_t *) read_aux_reg(ARC_REG_SCRATCH_DATA0); \
- pgd_base + pgd_index(addr); \
-})
-#else
-#define pgd_offset_fast(mm, addr) pgd_offset(mm, addr)
-#endif
-
extern pgd_t swapper_pg_dir[] __aligned(PAGE_SIZE);
void update_mmu_cache(struct vm_area_struct *vma, unsigned long address,
pte_t *ptep);
pud_t *pud, *pud_k;
pmd_t *pmd, *pmd_k;
- pgd = pgd_offset_fast(current->active_mm, address);
+ pgd = pgd_offset(current->active_mm, address);
pgd_k = pgd_offset_k(address);
if (!pgd_present(*pgd_k))
/* Enable the MMU */
write_aux_reg(ARC_REG_PID, MMU_ENABLE);
- /* In smp we use this reg for interrupt 1 scratch */
-#ifdef ARC_USE_SCRATCH_REG
+ /* In arc700/smp needed for re-entrant interrupt handling */
+#ifdef CONFIG_ISA_ARCV2
/* swapper_pg_dir is the pgd for the kernel, used by vmalloc */
write_aux_reg(ARC_REG_SCRATCH_DATA0, swapper_pg_dir);
#endif
lr r2, [efa]
-#ifdef ARC_USE_SCRATCH_REG
+#ifdef CONFIG_ISA_ARCV2
lr r1, [ARC_REG_SCRATCH_DATA0] ; current pgd
#else
GET_CURR_TASK_ON_CPU r1