ARM: dts: kirkwood: Add Ctera C-200 V1 board

Ctera C200 V1 is kirkwood-based 2-Bay NAS.

Hardware:
  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
  - NAND Flash: 256MB (Samsung 216 K9F2G08U0C)
  - Lan: 1x GBE (Marvell 88E1116R-NNC1)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 2.0 port
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 235ad55..31616f6 100644 (file)
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -281,6 +281,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \
 dtb-$(CONFIG_MACH_KIRKWOOD) += \
        kirkwood-b3.dtb \
        kirkwood-blackarmor-nas220.dtb \
+       kirkwood-c200-v1.dtb \
        kirkwood-cloudbox.dtb \
        kirkwood-d2net.dtb \
        kirkwood-db-88f6281.dtb \

diff --git a/arch/arm/boot/dts/kirkwood-c200-v1.dts b/arch/arm/boot/dts/kirkwood-c200-v1.dts
new file mode 100644 (file)
index 0000000..f59ff75
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts
@@ -0,0 +1,310 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Ctera C200 V1 Board Description
+ * Copyright 2021-2022 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+       model = "Ctera C200 V1";
+       compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+       chosen {
+               bootargs = "console=ttyS0,115200";
+               stdout-path = &uart0;
+       };
+
+       memory@0 {
+               device_type = "memory";
+               reg = <0x00000000 0x20000000>;
+       };
+
+       keys {
+               compatible = "gpio-keys";
+               pinctrl-0 = <&pmx_buttons>;
+               pinctrl-names = "default";
+
+               power {
+                       label = "Power Button";
+                       linux,code = <KEY_POWER>;
+                       gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+               };
+
+               reset {
+                       label = "Reset Button";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+               };
+
+               usb1 {
+                       label = "USB1 Button";
+                       linux,code = <BTN_0>;
+                       gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+               };
+
+               usb2 {
+                       label = "USB2 Button";
+                       linux,code = <BTN_1>;
+                       gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       gpio-poweroff {
+               compatible = "gpio-poweroff";
+               pinctrl-0 = <&pmx_poweroff>;
+               pinctrl-names = "default";
+               gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+               pinctrl-0 = <&pmx_leds>;
+               pinctrl-names = "default";
+
+               led-0 {
+                       function = LED_FUNCTION_DISK;
+                       function-enumerator = <2>;
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+               };
+
+               led-1 {
+                       function = LED_FUNCTION_DISK;
+                       function-enumerator = <1>;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+               };
+
+               led-2 {
+                       function = LED_FUNCTION_DISK;
+                       function-enumerator = <2>;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+               };
+
+               led-3 {
+                       function = LED_FUNCTION_DISK;
+                       function-enumerator = <1>;
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+               };
+
+               led-4 {
+                       function = LED_FUNCTION_STATUS;
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+               };
+
+               led-5 {
+                       function = LED_FUNCTION_STATUS;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+               };
+
+               led-6 {
+                       function = LED_FUNCTION_INDICATOR;
+                       color = <LED_COLOR_ID_BLUE>;
+                       gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+               };
+
+               led-7 {
+                       function = LED_FUNCTION_DISK_ERR;
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+               };
+
+               led-8 {
+                       function = LED_FUNCTION_DISK_ERR;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+               };
+
+               led-9 {
+                       function = LED_FUNCTION_USB;
+                       function-enumerator = <1>;
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+               };
+
+               led-10 {
+                       function = LED_FUNCTION_USB;
+                       function-enumerator = <1>;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "usbport";
+                       trigger-sources = <&hub_port2>;
+               };
+
+               led-11 {
+                       function = LED_FUNCTION_USB;
+                       function-enumerator = <2>;
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+               };
+
+               led-12 {
+                       function = LED_FUNCTION_USB;
+                       function-enumerator = <2>;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "usbport";
+                       trigger-sources = <&hub_port1>;
+               };
+       };
+};
+
+&eth0 {
+       status = "okay";
+};
+
+&eth0port {
+       phy-handle = <&ethphy9>;
+};
+
+&i2c0 {
+       status = "okay";
+
+       rtc@30 {
+               compatible = "s35390a";
+               reg = <0x30>;
+       };
+
+       lm63@4c {
+               compatible = "national,lm63";
+               reg = <0x4c>;
+       };
+};
+
+&mdio {
+       status = "okay";
+
+       ethphy9: ethernet-phy@9 {
+               reg = <9>;
+       };
+};
+
+&nand {
+       status = "okay";
+       chip-delay = <40>;
+
+       partition@0 {
+               label = "uboot";
+               reg = <0x0000000 0x200000>;
+       };
+
+       partition@200000 {
+               label = "certificate";
+               reg = <0x0200000 0x100000>;
+       };
+
+       partition@300000 {
+               label = "preset_cfg";
+               reg = <0x0300000 0x100000>;
+       };
+
+       partition@400000 {
+               label = "dev_params";
+               reg = <0x0400000 0x100000>;
+       };
+
+       partition@500000 {
+               label = "active_bank";
+               reg = <0x0500000 0x0100000>;
+       };
+
+       partition@600000 {
+               label = "magic";
+               reg = <0x0600000 0x0100000>;
+       };
+
+       partition@700000 {
+               label = "bank1";
+               reg = <0x0700000 0x2800000>;
+       };
+
+       partition@2f00000 {
+               label = "bank2";
+               reg = <0x2f00000 0x2800000>;
+       };
+
+       /* 0x5700000-0x5a00000 undefined in vendor firmware */
+
+       partition@5a00000 {
+               label = "reserved";
+               reg = <0x5a00000 0x2000000>;
+       };
+
+       partition@7a00000 {
+               label = "rootfs";
+               reg = <0x7a00000 0x8600000>;
+       };
+};
+
+&pinctrl {
+       /* Buzzer gpios are connected to two pins of buzzer.
+        * This buzzer require a modulated signal from gpio.
+        * Leave it as is due lack of proper driver.
+        */
+       pmx_buzzer: pmx-buzzer {
+               marvell,pins = "mpp12", "mpp13";
+               marvell,function = "gpio";
+       };
+
+       pmx_leds: pmx-leds {
+               marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38",
+                              "mpp39", "mpp40", "mpp42", "mpp43", "mpp44",
+                              "mpp45", "mpp46", "mpp47";
+               marvell,function = "gpio";
+       };
+
+       pmx_buttons: pmx-buttons {
+               marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49";
+               marvell,function = "gpio";
+       };
+
+       pmx_poweroff: pmx-poweroff {
+               marvell,pins = "mpp34";
+               marvell,function = "gpio";
+       };
+};
+
+&rtc {
+       status = "disabled";
+};
+
+&sata {
+       status = "okay";
+       nr-ports = <2>;
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&usb0 {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       port@1 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <1>;
+               #trigger-source-cells = <0>;
+
+               hub_port1: port@1 {
+                       reg = <1>;
+                       #trigger-source-cells = <0>;
+               };
+
+               hub_port2: port@2 {
+                       reg = <2>;
+                       #trigger-source-cells = <0>;
+               };
+       };
+};