keycode generated by each GPIO. Linux keycodes are defined in
<dt-bindings/input/input.h>.
+- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages
+ on GPIO bit changes. An array of up to 8 entries can be provided
+ indicating the Linux keycode mapped to each bit of the status byte,
+ starting at the LSB. Linux keycodes are defined in
+ <dt-bindings/input/input.h>.
+
+ Note: the numbering of the GPIOs and the bit they start at varies between
+ maXTouch devices. You must either refer to the documentation, or
+ experiment to determine which bit corresponds to which input. Use
+ KEY_RESERVED for unused padding values.
+
Example:
touch@4b {
--- /dev/null
+* Toshiba TC3589x multi-purpose expander
+
+The Toshiba TC3589x series are I2C-based MFD devices which may expose the
+following built-in devices: gpio, keypad, rotator (vibrator), PWM (for
+e.g. LEDs or vibrators) The included models are:
+
+- TC35890
+- TC35892
+- TC35893
+- TC35894
+- TC35895
+- TC35896
+
+Required properties:
+ - compatible : must be "toshiba,tc35890", "toshiba,tc35892", "toshiba,tc35893",
+ "toshiba,tc35894", "toshiba,tc35895" or "toshiba,tc35896"
+ - reg : I2C address of the device
+ - interrupt-parent : specifies which IRQ controller we're connected to
+ - interrupts : the interrupt on the parent the controller is connected to
+ - interrupt-controller : marks the device node as an interrupt controller
+ - #interrupt-cells : should be <1>, the first cell is the IRQ offset on this
+ TC3589x interrupt controller.
+
+Optional nodes:
+
+- GPIO
+ This GPIO module inside the TC3589x has 24 (TC35890, TC35892) or 20
+ (other models) GPIO lines.
+ - compatible : must be "toshiba,tc3589x-gpio"
+ - interrupts : interrupt on the parent, which must be the tc3589x MFD device
+ - interrupt-controller : marks the device node as an interrupt controller
+ - #interrupt-cells : should be <2>, the first cell is the IRQ offset on this
+ TC3589x GPIO interrupt controller, the second cell is the interrupt flags
+ in accordance with <dt-bindings/interrupt-controller/irq.h>. The following
+ flags are valid:
+ - IRQ_TYPE_LEVEL_LOW
+ - IRQ_TYPE_LEVEL_HIGH
+ - IRQ_TYPE_EDGE_RISING
+ - IRQ_TYPE_EDGE_FALLING
+ - IRQ_TYPE_EDGE_BOTH
+ - gpio-controller : marks the device node as a GPIO controller
+ - #gpio-cells : should be <2>, the first cell is the GPIO offset on this
+ GPIO controller, the second cell is the flags.
+
+- Keypad
+ This keypad is the same on all variants, supporting up to 96 different
+ keys. The linux-specific properties are modeled on those already existing
+ in other input drivers.
+ - compatible : must be "toshiba,tc3589x-keypad"
+ - debounce-delay-ms : debounce interval in milliseconds
+ - keypad,num-rows : number of rows in the matrix, see
+ bindings/input/matrix-keymap.txt
+ - keypad,num-columns : number of columns in the matrix, see
+ bindings/input/matrix-keymap.txt
+ - linux,keymap: the definition can be found in
+ bindings/input/matrix-keymap.txt
+ - linux,no-autorepeat: do no enable autorepeat feature.
+ - linux,wakeup: use any event on keypad as wakeup event.
+
+Example:
+
+tc35893@44 {
+ compatible = "toshiba,tc35893";
+ reg = <0x44>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ tc3589x_gpio {
+ compatible = "toshiba,tc3589x-gpio";
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ tc3589x_keypad {
+ compatible = "toshiba,tc3589x-keypad";
+ interrupts = <6>;
+ debounce-delay-ms = <4>;
+ keypad,num-columns = <8>;
+ keypad,num-rows = <8>;
+ linux,no-autorepeat;
+ linux,wakeup;
+ linux,keymap = <0x0301006b
+ 0x04010066
+ 0x06040072
+ 0x040200d7
+ 0x0303006a
+ 0x0205000e
+ 0x0607008b
+ 0x0500001c
+ 0x0403000b
+ 0x03040034
+ 0x05020067
+ 0x0305006c
+ 0x040500e7
+ 0x0005009e
+ 0x06020073
+ 0x01030039
+ 0x07060069
+ 0x050500d9>;
+ };
+};
width of 8 is assumed.
- ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
- "sw" <deprecated> use "ham1" instead
+ "sw" 1-bit Hamming ecc code via software
"hw" <deprecated> use "ham1" instead
"hw-romcode" <deprecated> use "ham1" instead
"ham1" 1-bit Hamming ecc code
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
- interrupts = <0 32 0x4>;
+ interrupts = <0 16 0x4>;
pinctrl-names = "default";
pinctrl-0 = <&gsbi5_uart_default>;
ADI AXI-SPDIF controller
Required properties:
- - compatible : Must be "adi,axi-spdif-1.00.a"
+ - compatible : Must be "adi,axi-spdif-tx-1.00.a"
- reg : Must contain SPDIF core's registers location and length
- clocks : Pairs of phandle and specifier referencing the controller's clocks.
The controller expects two clocks, the clock used for the AXI interface and
size_t size, int flags,
const char *exp_name)
- If this succeeds, dma_buf_export allocates a dma_buf structure, and returns a
- pointer to the same. It also associates an anonymous file with this buffer,
- so it can be exported. On failure to allocate the dma_buf object, it returns
- NULL.
+ If this succeeds, dma_buf_export_named allocates a dma_buf structure, and
+ returns a pointer to the same. It also associates an anonymous file with this
+ buffer, so it can be exported. On failure to allocate the dma_buf object,
+ it returns NULL.
'exp_name' is the name of exporter - to facilitate information while
debugging.
drivers and/or processes.
Interface:
- int dma_buf_fd(struct dma_buf *dmabuf)
+ int dma_buf_fd(struct dma_buf *dmabuf, int flags)
This API installs an fd for the anonymous file associated with this buffer;
returns either 'fd', or error.
"dma_buf->ops->" indirection from the users of this interface.
In struct dma_buf_ops, unmap_dma_buf is defined as
- void (*unmap_dma_buf)(struct dma_buf_attachment *, struct sg_table *);
+ void (*unmap_dma_buf)(struct dma_buf_attachment *,
+ struct sg_table *,
+ enum dma_data_direction);
unmap_dma_buf signifies the end-of-DMA for the attachment provided. Like
map_dma_buf, this API also must be implemented by the exporter.
a remote system.
Kdump and kexec are currently supported on the x86, x86_64, ppc64, ia64,
-and s390x architectures.
+s390x and arm architectures.
When the system kernel boots, it reserves a small section of memory for
the dump-capture kernel. This ensures that ongoing Direct Memory Access
2) Or use the system kernel binary itself as dump-capture kernel and there is
no need to build a separate dump-capture kernel. This is possible
only with the architectures which support a relocatable kernel. As
- of today, i386, x86_64, ppc64 and ia64 architectures support relocatable
+ of today, i386, x86_64, ppc64, ia64 and arm architectures support relocatable
kernel.
Building a relocatable kernel is advantageous from the point of view that
kernel will be aligned to 64Mb, so if the start address is not then
any space below the alignment point will be wasted.
+Dump-capture kernel config options (Arch Dependent, arm)
+----------------------------------------------------------
+
+- To use a relocatable kernel,
+ Enable "AUTO_ZRELADDR" support under "Boot" options:
+
+ AUTO_ZRELADDR=y
Extended crashkernel syntax
===========================
crashkernel=<range1>:<size1>[,<range2>:<size2>,...][@offset]
range=start-[end]
+Please note, on arm, the offset is required.
+ crashkernel=<range1>:<size1>[,<range2>:<size2>,...]@offset
+ range=start-[end]
+
'start' is inclusive and 'end' is exclusive.
For example:
on the memory consumption of the kdump system. In general this is not
dependent on the memory size of the production system.
+ On arm, use "crashkernel=Y@X". Note that the start address of the kernel
+ will be aligned to 128MiB (0x08000000), so if the start address is not then
+ any space below the alignment point may be overwritten by the dump-capture kernel,
+ which means it is possible that the vmcore is not that precise as expected.
+
+
Load the Dump-capture Kernel
============================
- Use vmlinux or vmlinuz.gz
For s390x:
- Use image or bzImage
-
+For arm:
+ - Use zImage
If you are using a uncompressed vmlinux image then use following command
to load dump-capture kernel.
--initrd=<initrd-for-dump-capture-kernel> \
--append="root=<root-dev> <arch-specific-options>"
+If you are using a compressed zImage, then use following command
+to load dump-capture kernel.
+
+ kexec --type zImage -p <dump-capture-kernel-bzImage> \
+ --initrd=<initrd-for-dump-capture-kernel> \
+ --dtb=<dtb-for-dump-capture-kernel> \
+ --append="root=<root-dev> <arch-specific-options>"
+
+
Please note, that --args-linux does not need to be specified for ia64.
It is planned to make this a no-op on that architecture, but for now
it should be omitted
For s390x:
"1 maxcpus=1 cgroup_disable=memory"
+For arm:
+ "1 maxcpus=1 reset_devices"
+
Notes on loading the dump-capture kernel:
* By default, the ELF headers are stored in ELF64 format to support
-------------------
this_cpu operations are a way of optimizing access to per cpu
-variables associated with the *currently* executing processor through
-the use of segment registers (or a dedicated register where the cpu
-permanently stored the beginning of the per cpu area for a specific
-processor).
+variables associated with the *currently* executing processor. This is
+done through the use of segment registers (or a dedicated register where
+the cpu permanently stored the beginning of the per cpu area for a
+specific processor).
-The this_cpu operations add a per cpu variable offset to the processor
-specific percpu base and encode that operation in the instruction
+this_cpu operations add a per cpu variable offset to the processor
+specific per cpu base and encode that operation in the instruction
operating on the per cpu variable.
-This means there are no atomicity issues between the calculation of
+This means that there are no atomicity issues between the calculation of
the offset and the operation on the data. Therefore it is not
-necessary to disable preempt or interrupts to ensure that the
+necessary to disable preemption or interrupts to ensure that the
processor is not changed between the calculation of the address and
the operation on the data.
Read-modify-write operations are of particular interest. Frequently
processors have special lower latency instructions that can operate
-without the typical synchronization overhead but still provide some
-sort of relaxed atomicity guarantee. The x86 for example can execute
-RMV (Read Modify Write) instructions like inc/dec/cmpxchg without the
+without the typical synchronization overhead, but still provide some
+sort of relaxed atomicity guarantees. The x86, for example, can execute
+RMW (Read Modify Write) instructions like inc/dec/cmpxchg without the
lock prefix and the associated latency penalty.
Access to the variable without the lock prefix is not synchronized but
processor should be accessing that variable and therefore there are no
concurrency issues with other processors in the system.
+Please note that accesses by remote processors to a per cpu area are
+exceptional situations and may impact performance and/or correctness
+(remote write operations) of local RMW operations via this_cpu_*.
+
+The main use of the this_cpu operations has been to optimize counter
+operations.
+
+The following this_cpu() operations with implied preemption protection
+are defined. These operations can be used without worrying about
+preemption and interrupts.
+
+ this_cpu_add()
+ this_cpu_read(pcp)
+ this_cpu_write(pcp, val)
+ this_cpu_add(pcp, val)
+ this_cpu_and(pcp, val)
+ this_cpu_or(pcp, val)
+ this_cpu_add_return(pcp, val)
+ this_cpu_xchg(pcp, nval)
+ this_cpu_cmpxchg(pcp, oval, nval)
+ this_cpu_cmpxchg_double(pcp1, pcp2, oval1, oval2, nval1, nval2)
+ this_cpu_sub(pcp, val)
+ this_cpu_inc(pcp)
+ this_cpu_dec(pcp)
+ this_cpu_sub_return(pcp, val)
+ this_cpu_inc_return(pcp)
+ this_cpu_dec_return(pcp)
+
+
+Inner working of this_cpu operations
+------------------------------------
+
On x86 the fs: or the gs: segment registers contain the base of the
per cpu area. It is then possible to simply use the segment override
to relocate a per cpu relative address to the proper per cpu area for
mov ax, gs:[x]
instead of a sequence of calculation of the address and then a fetch
-from that address which occurs with the percpu operations. Before
+from that address which occurs with the per cpu operations. Before
this_cpu_ops such sequence also required preempt disable/enable to
prevent the kernel from moving the thread to a different processor
while the calculation is performed.
-The main use of the this_cpu operations has been to optimize counter
-operations.
+Consider the following this_cpu operation:
this_cpu_inc(x)
-results in the following single instruction (no lock prefix!)
+The above results in the following single instruction (no lock prefix!)
inc gs:[x]
instead of the following operations required if there is no segment
-register.
+register:
int *y;
int cpu;
(*y)++;
put_cpu();
-Note that these operations can only be used on percpu data that is
+Note that these operations can only be used on per cpu data that is
reserved for a specific processor. Without disabling preemption in the
surrounding code this_cpu_inc() will only guarantee that one of the
-percpu counters is correctly incremented. However, there is no
+per cpu counters is correctly incremented. However, there is no
guarantee that the OS will not move the process directly before or
after the this_cpu instruction is executed. In general this means that
the value of the individual counters for each processor are
Per cpu variables are used for performance reasons. Bouncing cache
lines can be avoided if multiple processors concurrently go through
the same code paths. Since each processor has its own per cpu
-variables no concurrent cacheline updates take place. The price that
+variables no concurrent cache line updates take place. The price that
has to be paid for this optimization is the need to add up the per cpu
-counters when the value of the counter is needed.
+counters when the value of a counter is needed.
Special operations:
of the per cpu variable that belongs to the currently executing
processor. this_cpu_ptr avoids multiple steps that the common
get_cpu/put_cpu sequence requires. No processor number is
-available. Instead the offset of the local per cpu area is simply
-added to the percpu offset.
+available. Instead, the offset of the local per cpu area is simply
+added to the per cpu offset.
+Note that this operation is usually used in a code segment when
+preemption has been disabled. The pointer is then used to
+access local per cpu data in a critical section. When preemption
+is re-enabled this pointer is usually no longer useful since it may
+no longer point to per cpu data of the current processor.
Per cpu variables and offsets
-----------------------------
-Per cpu variables have *offsets* to the beginning of the percpu
+Per cpu variables have *offsets* to the beginning of the per cpu
area. They do not have addresses although they look like that in the
code. Offsets cannot be directly dereferenced. The offset must be
-added to a base pointer of a percpu area of a processor in order to
+added to a base pointer of a per cpu area of a processor in order to
form a valid address.
Therefore the use of x or &x outside of the context of per cpu
operations is invalid and will generally be treated like a NULL
pointer dereference.
-In the context of per cpu operations
+ DEFINE_PER_CPU(int, x);
- x is a per cpu variable. Most this_cpu operations take a cpu
- variable.
+In the context of per cpu operations the above implies that x is a per
+cpu variable. Most this_cpu operations take a cpu variable.
- &x is the *offset* a per cpu variable. this_cpu_ptr() takes
- the offset of a per cpu variable which makes this look a bit
- strange.
+ int __percpu *p = &x;
+&x and hence p is the *offset* of a per cpu variable. this_cpu_ptr()
+takes the offset of a per cpu variable which makes this look a bit
+strange.
Operations on a field of a per cpu structure
struct s __percpu *ps = &p;
- z = this_cpu_dec(ps->m);
+ this_cpu_dec(ps->m);
z = this_cpu_inc_return(ps->n);
Variants of this_cpu ops
-------------------------
-this_cpu ops are interrupt safe. Some architecture do not support
+this_cpu ops are interrupt safe. Some architectures do not support
these per cpu local operations. In that case the operation must be
replaced by code that disables interrupts, then does the operations
-that are guaranteed to be atomic and then reenable interrupts. Doing
+that are guaranteed to be atomic and then re-enable interrupts. Doing
so is expensive. If there are other reasons why the scheduler cannot
change the processor we are executing on then there is no reason to
-disable interrupts. For that purpose the __this_cpu operations are
-provided. For example.
-
- __this_cpu_inc(x);
-
-Will increment x and will not fallback to code that disables
+disable interrupts. For that purpose the following __this_cpu operations
+are provided.
+
+These operations have no guarantee against concurrent interrupts or
+preemption. If a per cpu variable is not used in an interrupt context
+and the scheduler cannot preempt, then they are safe. If any interrupts
+still occur while an operation is in progress and if the interrupt too
+modifies the variable, then RMW actions can not be guaranteed to be
+safe.
+
+ __this_cpu_add()
+ __this_cpu_read(pcp)
+ __this_cpu_write(pcp, val)
+ __this_cpu_add(pcp, val)
+ __this_cpu_and(pcp, val)
+ __this_cpu_or(pcp, val)
+ __this_cpu_add_return(pcp, val)
+ __this_cpu_xchg(pcp, nval)
+ __this_cpu_cmpxchg(pcp, oval, nval)
+ __this_cpu_cmpxchg_double(pcp1, pcp2, oval1, oval2, nval1, nval2)
+ __this_cpu_sub(pcp, val)
+ __this_cpu_inc(pcp)
+ __this_cpu_dec(pcp)
+ __this_cpu_sub_return(pcp, val)
+ __this_cpu_inc_return(pcp)
+ __this_cpu_dec_return(pcp)
+
+
+Will increment x and will not fall-back to code that disables
interrupts on platforms that cannot accomplish atomicity through
address relocation and a Read-Modify-Write operation in the same
instruction.
-
&this_cpu_ptr(pp)->n vs this_cpu_ptr(&pp->n)
--------------------------------------------
The first operation takes the offset and forms an address and then
-adds the offset of the n field.
+adds the offset of the n field. This may result in two add
+instructions emitted by the compiler.
The second one first adds the two offsets and then does the
relocation. IMHO the second form looks cleaner and has an easier time
this_cpu_read() and friends are used.
-Christoph Lameter, April 3rd, 2013
+Remote access to per cpu data
+------------------------------
+
+Per cpu data structures are designed to be used by one cpu exclusively.
+If you use the variables as intended, this_cpu_ops() are guaranteed to
+be "atomic" as no other CPU has access to these data structures.
+
+There are special cases where you might need to access per cpu data
+structures remotely. It is usually safe to do a remote read access
+and that is frequently done to summarize counters. Remote write access
+something which could be problematic because this_cpu ops do not
+have lock semantics. A remote write may interfere with a this_cpu
+RMW operation.
+
+Remote write accesses to percpu data structures are highly discouraged
+unless absolutely necessary. Please consider using an IPI to wake up
+the remote CPU and perform the update to its per cpu area.
+
+To access per-cpu data structure remotely, typically the per_cpu_ptr()
+function is used:
+
+
+ DEFINE_PER_CPU(struct data, datap);
+
+ struct data *p = per_cpu_ptr(&datap, cpu);
+
+This makes it explicit that we are getting ready to access a percpu
+area remotely.
+
+You can also do the following to convert the datap offset to an address
+
+ struct data *p = this_cpu_ptr(&datap);
+
+but, passing of pointers calculated via this_cpu_ptr to other cpus is
+unusual and should be avoided.
+
+Remote access are typically only for reading the status of another cpus
+per cpu data. Write accesses can cause unique problems due to the
+relaxed synchronization requirements for this_cpu operations.
+
+One example that illustrates some concerns with write operations is
+the following scenario that occurs because two per cpu variables
+share a cache-line but the relaxed synchronization is applied to
+only one process updating the cache-line.
+
+Consider the following example
+
+
+ struct test {
+ atomic_t a;
+ int b;
+ };
+
+ DEFINE_PER_CPU(struct test, onecacheline);
+
+There is some concern about what would happen if the field 'a' is updated
+remotely from one processor and the local processor would use this_cpu ops
+to update field b. Care should be taken that such simultaneous accesses to
+data within the same cache line are avoided. Also costly synchronization
+may be necessary. IPIs are generally recommended in such scenarios instead
+of a remote write to the per cpu area of another processor.
+
+Even in cases where the remote writes are rare, please bear in
+mind that a remote write will evict the cache line from the processor
+that most likely will access it. If the processor wakes up and finds a
+missing local cache line of a per cpu area, its performance and hence
+the wake up times will be affected.
+
+Christoph Lameter, August 4th, 2014
+Pranith Kumar, Aug 2nd, 2014
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: linux-rockchip@lists.infradead.org
S: Maintained
+F: arch/arm/boot/dts/rk3*
F: arch/arm/mach-rockchip/
+F: drivers/clk/rockchip/
+F: drivers/i2c/busses/i2c-rk3x.c
F: drivers/*/*rockchip*
+F: drivers/*/*/*rockchip*
+F: sound/soc/rockchip/
ARM/SAMSUNG ARM ARCHITECTURES
M: Ben Dooks <ben-linux@fluff.org>
F: Documentation/usb/ohci.txt
F: drivers/usb/host/ohci*
+USB OVER IP DRIVER
+M: Valentina Manea <valentina.manea.m@gmail.com>
+M: Shuah Khan <shuah.kh@samsung.com>
+L: linux-usb@vger.kernel.org
+S: Maintained
+F: drivers/usb/usbip/
+F: tools/usb/usbip/
+
USB PEGASUS DRIVER
M: Petko Manolov <petkan@nucleusys.com>
L: linux-usb@vger.kernel.org
F: arch/x86/
X86 PLATFORM DRIVERS
-M: Matthew Garrett <matthew.garrett@nebula.com>
+M: Darren Hart <dvhart@infradead.org>
L: platform-driver-x86@vger.kernel.org
-T: git git://cavan.codon.org.uk/platform-drivers-x86.git
+T: git git://git.infradead.org/users/dvhart/linux-platform-drivers-x86.git
S: Maintained
F: drivers/platform/x86/
VERSION = 3
PATCHLEVEL = 17
SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
NAME = Shuffling Zombie Juror
# *DOCUMENTATION*
#define outb_p outb
#define outw_p outw
#define outl_p outl
-#define readb_relaxed(addr) __raw_readb(addr)
-#define readw_relaxed(addr) __raw_readw(addr)
-#define readl_relaxed(addr) __raw_readl(addr)
-#define readq_relaxed(addr) __raw_readq(addr)
+#define readb_relaxed(addr) __raw_readb(addr)
+#define readw_relaxed(addr) __raw_readw(addr)
+#define readl_relaxed(addr) __raw_readl(addr)
+#define readq_relaxed(addr) __raw_readq(addr)
+#define writeb_relaxed(b, addr) __raw_writeb(b, addr)
+#define writew_relaxed(b, addr) __raw_writew(b, addr)
+#define writel_relaxed(b, addr) __raw_writel(b, addr)
+#define writeq_relaxed(b, addr) __raw_writeq(b, addr)
#define mmiowb()
#include <uapi/asm/unistd.h>
-#define NR_SYSCALLS 508
+#define NR_SYSCALLS 511
#define __ARCH_WANT_OLD_READDIR
#define __ARCH_WANT_STAT64
#define __NR_process_vm_writev 505
#define __NR_kcmp 506
#define __NR_finit_module 507
+#define __NR_sched_setattr 508
+#define __NR_sched_getattr 509
+#define __NR_renameat2 510
#endif /* _UAPI_ALPHA_UNISTD_H */
.quad sys_process_vm_writev /* 505 */
.quad sys_kcmp
.quad sys_finit_module
+ .quad sys_sched_setattr
+ .quad sys_sched_getattr
+ .quad sys_renameat2 /* 510 */
.size sys_call_table, . - sys_call_table
.type sys_call_table, @object
static void __ic_line_inv_vaddr_helper(void *info)
{
- struct ic_inv *ic_inv_args = (struct ic_inv_args *) info;
+ struct ic_inv_args *ic_inv = info;
__ic_line_inv_vaddr_local(ic_inv->paddr, ic_inv->vaddr, ic_inv->sz);
}
tot_sz -= sz;
}
}
+EXPORT_SYMBOL(flush_icache_range);
/*
* General purpose helper to make I and D cache lines consistent.
config KEXEC
bool "Kexec system call (EXPERIMENTAL)"
depends on (!SMP || PM_SLEEP_SMP)
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio2: gpio@48055000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio3: gpio@48057000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio4: gpio@48059000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio5: gpio@4805b000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio6: gpio@4805d000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio7: gpio@48051000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio8: gpio@48053000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
uart1: serial@4806a000 {
MX53_PAD_CSI0_DAT9__I2C1_SCL 0x400001ec
>;
};
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT5__GPIO5_23 0x1e4 /* IRQ */
+ >;
+ };
};
};
pmic: mc34708@8 {
compatible = "fsl,mc34708";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
reg = <0x08>;
interrupt-parent = <&gpio5>;
interrupts = <23 0x8>;
sound-spdif {
compatible = "fsl,imx-audio-spdif";
- model = "imx-spdif";
+ model = "On-board SPDIF";
/* IMX6 doesn't implement this yet */
spdif-controller = <&spdif>;
spdif-out;
};
&usbh1 {
+ disable-over-current;
vbus-supply = <®_usbh1_vbus>;
status = "okay";
};
&usbotg {
+ disable-over-current;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
vbus-supply = <®_usbotg_vbus>;
sound-spdif {
compatible = "fsl,imx-audio-spdif";
- model = "imx-spdif";
+ model = "Integrated SPDIF";
/* IMX6 doesn't implement this yet */
spdif-controller = <&spdif>;
spdif-out;
fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
};
+ pinctrl_cubox_i_usbh1: cubox-i-usbh1 {
+ fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>;
+ };
+
pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
};
- pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id {
+ pinctrl_cubox_i_usbotg: cubox-i-usbotg {
/*
- * The Cubox-i pulls this low, but as it's pointless
+ * The Cubox-i pulls ID low, but as it's pointless
* leaving it as a pull-up, even if it is just 10uA.
*/
- fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
};
pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
};
&usbh1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_usbh1>;
vbus-supply = <®_usbh1_vbus>;
status = "okay";
};
&usbotg {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>;
+ pinctrl-0 = <&pinctrl_cubox_i_usbotg>;
vbus-supply = <®_usbotg_vbus>;
status = "okay";
};
enet {
pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
fsl,pins = <
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b8b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
/* AR8035 reset */
MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
+ interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
};
&gpio1 {
};
twl_power: power {
- compatible = "ti,twl4030-power-n900";
+ compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
ti,use_poweroff;
};
};
#address-cells = <1>;
#size-cells = <1>;
reg = <1 0 0x08000000>;
- ti,nand-ecc-opt = "ham1";
+ ti,nand-ecc-opt = "sw";
nand-bus-width = <8>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <36>;
l3_iclk_div: l3_iclk_div {
#clock-cells = <0>;
- compatible = "fixed-factor-clock";
+ compatible = "ti,divider-clock";
+ ti,max-div = <2>;
+ ti,bit-shift = <4>;
+ reg = <0x100>;
clocks = <&dpll_core_h12x2_ck>;
- clock-mult = <1>;
- clock-div = <1>;
+ ti,index-power-of-two;
};
gpu_l3_iclk: gpu_l3_iclk {
l4_root_clk_div: l4_root_clk_div {
#clock-cells = <0>;
- compatible = "fixed-factor-clock";
+ compatible = "ti,divider-clock";
+ ti,max-div = <2>;
+ ti,bit-shift = <8>;
+ reg = <0x100>;
clocks = <&l3_iclk_div>;
- clock-mult = <1>;
- clock-div = <1>;
+ ti,index-power-of-two;
};
slimbus1_slimbus_clk: slimbus1_slimbus_clk {
regulator-always-on;
};
- clk32kg: regulator-clk32kg {
- compatible = "ti,twl6030-clk32kg";
- };
-
twl_usb_comparator: usb-comparator {
compatible = "ti,twl6030-usb";
interrupts = <4>, <10>;
"mcr p15, 0, r0, c1, c0, 0 @ set SCTLR \n\t" \
"isb \n\t" \
"bl v7_flush_dcache_"__stringify(level)" \n\t" \
- "clrex \n\t" \
"mrc p15, 0, r0, c1, c0, 1 @ get ACTLR \n\t" \
"bic r0, r0, #(1 << 6) @ disable local coherency \n\t" \
"mcr p15, 0, r0, c1, c0, 1 @ set ACTLR \n\t" \
#define ARM_CPU_PART_CORTEX_A12 0x4100c0d0
#define ARM_CPU_PART_CORTEX_A17 0x4100c0e0
#define ARM_CPU_PART_CORTEX_A15 0x4100c0f0
+#define ARM_CPU_PART_MASK 0xff00fff0
#define ARM_CPU_XSCALE_ARCH_MASK 0xe000
#define ARM_CPU_XSCALE_ARCH_V1 0x2000
*/
static inline unsigned int __attribute_const__ read_cpuid_part(void)
{
- return read_cpuid_id() & 0xff00fff0;
+ return read_cpuid_id() & ARM_CPU_PART_MASK;
}
static inline unsigned int __attribute_const__ __deprecated read_cpuid_part_number(void)
#define R_ARM_ABS32 2
#define R_ARM_CALL 28
#define R_ARM_JUMP24 29
+#define R_ARM_TARGET1 38
#define R_ARM_V4BX 40
#define R_ARM_PREL31 42
#define R_ARM_MOVW_ABS_NC 43
#include <linux/cpumask.h>
#include <linux/err.h>
+#include <asm/cpu.h>
#include <asm/cputype.h>
/*
#endif
}
+/**
+ * smp_cpuid_part() - return part id for a given cpu
+ * @cpu: logical cpu id.
+ *
+ * Return: part id of logical cpu passed as argument.
+ */
+static inline unsigned int smp_cpuid_part(int cpu)
+{
+ struct cpuinfo_arm *cpu_info = &per_cpu(cpu_data, cpu);
+
+ return is_smp() ? cpu_info->cpuid & ARM_CPU_PART_MASK :
+ read_cpuid_part();
+}
+
/* all SMP configurations have the extended CPUID registers */
#ifndef CONFIG_MMU
#define tlb_ops_need_broadcast() 0
#endif
.endif
msr spsr_cxsf, \rpsr
-#if defined(CONFIG_CPU_V6)
- ldr r0, [sp]
- strex r1, r2, [sp] @ clear the exclusive monitor
- ldmib sp, {r1 - pc}^ @ load r1 - pc, cpsr
-#elif defined(CONFIG_CPU_32v6K)
- clrex @ clear the exclusive monitor
- ldmia sp, {r0 - pc}^ @ load r0 - pc, cpsr
-#else
- ldmia sp, {r0 - pc}^ @ load r0 - pc, cpsr
+#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_32v6K)
+ @ We must avoid clrex due to Cortex-A15 erratum #830321
+ sub r0, sp, #4 @ uninhabited address
+ strex r1, r2, [r0] @ clear the exclusive monitor
#endif
+ ldmia sp, {r0 - pc}^ @ load r0 - pc, cpsr
.endm
.macro restore_user_regs, fast = 0, offset = 0
ldr r1, [sp, #\offset + S_PSR] @ get calling cpsr
ldr lr, [sp, #\offset + S_PC]! @ get pc
msr spsr_cxsf, r1 @ save in spsr_svc
-#if defined(CONFIG_CPU_V6)
+#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_32v6K)
+ @ We must avoid clrex due to Cortex-A15 erratum #830321
strex r1, r2, [sp] @ clear the exclusive monitor
-#elif defined(CONFIG_CPU_32v6K)
- clrex @ clear the exclusive monitor
#endif
.if \fast
ldmdb sp, {r1 - lr}^ @ get calling r1 - lr
.endif
ldr lr, [sp, #S_SP] @ top of the stack
ldrd r0, r1, [sp, #S_LR] @ calling lr and pc
- clrex @ clear the exclusive monitor
+
+ @ We must avoid clrex due to Cortex-A15 erratum #830321
+ strex r2, r1, [sp, #S_LR] @ clear the exclusive monitor
+
stmdb lr!, {r0, r1, \rpsr} @ calling lr and rfe context
ldmia sp, {r0 - r12}
mov sp, lr
.endm
#else /* ifdef CONFIG_CPU_V7M */
.macro restore_user_regs, fast = 0, offset = 0
- clrex @ clear the exclusive monitor
mov r2, sp
load_user_sp_lr r2, r3, \offset + S_SP @ calling sp, lr
ldr r1, [sp, #\offset + S_PSR] @ get calling cpsr
ldr lr, [sp, #\offset + S_PC] @ get pc
add sp, sp, #\offset + S_SP
msr spsr_cxsf, r1 @ save in spsr_svc
+
+ @ We must avoid clrex due to Cortex-A15 erratum #830321
+ strex r1, r2, [sp] @ clear the exclusive monitor
+
.if \fast
ldmdb sp, {r1 - r12} @ get calling r1 - r12
.else
break;
case R_ARM_ABS32:
+ case R_ARM_TARGET1:
*(u32 *)loc += sym->st_value;
break;
ifeq ($(CONFIG_ARCH_BRCMSTB),y)
obj-y += brcmstb.o
-obj-$(CONFIG_SMP) += headsmp-brcmstb.o platsmp-brcmstb.o
endif
+++ /dev/null
-/*
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __BRCMSTB_H__
-#define __BRCMSTB_H__
-
-void brcmstb_secondary_startup(void);
-
-#endif /* __BRCMSTB_H__ */
+++ /dev/null
-/*
- * SMP boot code for secondary CPUs
- * Based on arch/arm/mach-tegra/headsmp.S
- *
- * Copyright (C) 2010 NVIDIA, Inc.
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <asm/assembler.h>
-#include <linux/linkage.h>
-#include <linux/init.h>
-
- .section ".text.head", "ax"
-
-ENTRY(brcmstb_secondary_startup)
- /*
- * Ensure CPU is in a sane state by disabling all IRQs and switching
- * into SVC mode.
- */
- setmode PSR_I_BIT | PSR_F_BIT | SVC_MODE, r0
-
- bl v7_invalidate_l1
- b secondary_startup
-ENDPROC(brcmstb_secondary_startup)
+++ /dev/null
-/*
- * Broadcom STB CPU SMP and hotplug support for ARM
- *
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/of_address.h>
-#include <linux/of_platform.h>
-#include <linux/printk.h>
-#include <linux/regmap.h>
-#include <linux/smp.h>
-#include <linux/mfd/syscon.h>
-#include <linux/spinlock.h>
-
-#include <asm/cacheflush.h>
-#include <asm/cp15.h>
-#include <asm/mach-types.h>
-#include <asm/smp_plat.h>
-
-#include "brcmstb.h"
-
-enum {
- ZONE_MAN_CLKEN_MASK = BIT(0),
- ZONE_MAN_RESET_CNTL_MASK = BIT(1),
- ZONE_MAN_MEM_PWR_MASK = BIT(4),
- ZONE_RESERVED_1_MASK = BIT(5),
- ZONE_MAN_ISO_CNTL_MASK = BIT(6),
- ZONE_MANUAL_CONTROL_MASK = BIT(7),
- ZONE_PWR_DN_REQ_MASK = BIT(9),
- ZONE_PWR_UP_REQ_MASK = BIT(10),
- ZONE_BLK_RST_ASSERT_MASK = BIT(12),
- ZONE_PWR_OFF_STATE_MASK = BIT(25),
- ZONE_PWR_ON_STATE_MASK = BIT(26),
- ZONE_DPG_PWR_STATE_MASK = BIT(28),
- ZONE_MEM_PWR_STATE_MASK = BIT(29),
- ZONE_RESET_STATE_MASK = BIT(31),
- CPU0_PWR_ZONE_CTRL_REG = 1,
- CPU_RESET_CONFIG_REG = 2,
-};
-
-static void __iomem *cpubiuctrl_block;
-static void __iomem *hif_cont_block;
-static u32 cpu0_pwr_zone_ctrl_reg;
-static u32 cpu_rst_cfg_reg;
-static u32 hif_cont_reg;
-
-#ifdef CONFIG_HOTPLUG_CPU
-static DEFINE_PER_CPU_ALIGNED(int, per_cpu_sw_state);
-
-static int per_cpu_sw_state_rd(u32 cpu)
-{
- sync_cache_r(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
- return per_cpu(per_cpu_sw_state, cpu);
-}
-
-static void per_cpu_sw_state_wr(u32 cpu, int val)
-{
- per_cpu(per_cpu_sw_state, cpu) = val;
- dmb();
- sync_cache_w(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
- dsb_sev();
-}
-#else
-static inline void per_cpu_sw_state_wr(u32 cpu, int val) { }
-#endif
-
-static void __iomem *pwr_ctrl_get_base(u32 cpu)
-{
- void __iomem *base = cpubiuctrl_block + cpu0_pwr_zone_ctrl_reg;
- base += (cpu_logical_map(cpu) * 4);
- return base;
-}
-
-static u32 pwr_ctrl_rd(u32 cpu)
-{
- void __iomem *base = pwr_ctrl_get_base(cpu);
- return readl_relaxed(base);
-}
-
-static void pwr_ctrl_wr(u32 cpu, u32 val)
-{
- void __iomem *base = pwr_ctrl_get_base(cpu);
- writel(val, base);
-}
-
-static void cpu_rst_cfg_set(u32 cpu, int set)
-{
- u32 val;
- val = readl_relaxed(cpubiuctrl_block + cpu_rst_cfg_reg);
- if (set)
- val |= BIT(cpu_logical_map(cpu));
- else
- val &= ~BIT(cpu_logical_map(cpu));
- writel_relaxed(val, cpubiuctrl_block + cpu_rst_cfg_reg);
-}
-
-static void cpu_set_boot_addr(u32 cpu, unsigned long boot_addr)
-{
- const int reg_ofs = cpu_logical_map(cpu) * 8;
- writel_relaxed(0, hif_cont_block + hif_cont_reg + reg_ofs);
- writel_relaxed(boot_addr, hif_cont_block + hif_cont_reg + 4 + reg_ofs);
-}
-
-static void brcmstb_cpu_boot(u32 cpu)
-{
- pr_info("SMP: Booting CPU%d...\n", cpu);
-
- /*
- * set the reset vector to point to the secondary_startup
- * routine
- */
- cpu_set_boot_addr(cpu, virt_to_phys(brcmstb_secondary_startup));
-
- /* unhalt the cpu */
- cpu_rst_cfg_set(cpu, 0);
-}
-
-static void brcmstb_cpu_power_on(u32 cpu)
-{
- /*
- * The secondary cores power was cut, so we must go through
- * power-on initialization.
- */
- u32 tmp;
-
- pr_info("SMP: Powering up CPU%d...\n", cpu);
-
- /* Request zone power up */
- pwr_ctrl_wr(cpu, ZONE_PWR_UP_REQ_MASK);
-
- /* Wait for the power up FSM to complete */
- do {
- tmp = pwr_ctrl_rd(cpu);
- } while (!(tmp & ZONE_PWR_ON_STATE_MASK));
-
- per_cpu_sw_state_wr(cpu, 1);
-}
-
-static int brcmstb_cpu_get_power_state(u32 cpu)
-{
- int tmp = pwr_ctrl_rd(cpu);
- return (tmp & ZONE_RESET_STATE_MASK) ? 0 : 1;
-}
-
-#ifdef CONFIG_HOTPLUG_CPU
-
-static void brcmstb_cpu_die(u32 cpu)
-{
- v7_exit_coherency_flush(all);
-
- /* Prevent all interrupts from reaching this CPU. */
- arch_local_irq_disable();
-
- /*
- * Final full barrier to ensure everything before this instruction has
- * quiesced.
- */
- isb();
- dsb();
-
- per_cpu_sw_state_wr(cpu, 0);
-
- /* Sit and wait to die */
- wfi();
-
- /* We should never get here... */
- panic("Spurious interrupt on CPU %d received!\n", cpu);
-}
-
-static int brcmstb_cpu_kill(u32 cpu)
-{
- u32 tmp;
-
- pr_info("SMP: Powering down CPU%d...\n", cpu);
-
- while (per_cpu_sw_state_rd(cpu))
- ;
-
- /* Program zone reset */
- pwr_ctrl_wr(cpu, ZONE_RESET_STATE_MASK | ZONE_BLK_RST_ASSERT_MASK |
- ZONE_PWR_DN_REQ_MASK);
-
- /* Verify zone reset */
- tmp = pwr_ctrl_rd(cpu);
- if (!(tmp & ZONE_RESET_STATE_MASK))
- pr_err("%s: Zone reset bit for CPU %d not asserted!\n",
- __func__, cpu);
-
- /* Wait for power down */
- do {
- tmp = pwr_ctrl_rd(cpu);
- } while (!(tmp & ZONE_PWR_OFF_STATE_MASK));
-
- /* Settle-time from Broadcom-internal DVT reference code */
- udelay(7);
-
- /* Assert reset on the CPU */
- cpu_rst_cfg_set(cpu, 1);
-
- return 1;
-}
-
-#endif /* CONFIG_HOTPLUG_CPU */
-
-static int __init setup_hifcpubiuctrl_regs(struct device_node *np)
-{
- int rc = 0;
- char *name;
- struct device_node *syscon_np = NULL;
-
- name = "syscon-cpu";
-
- syscon_np = of_parse_phandle(np, name, 0);
- if (!syscon_np) {
- pr_err("can't find phandle %s\n", name);
- rc = -EINVAL;
- goto cleanup;
- }
-
- cpubiuctrl_block = of_iomap(syscon_np, 0);
- if (!cpubiuctrl_block) {
- pr_err("iomap failed for cpubiuctrl_block\n");
- rc = -EINVAL;
- goto cleanup;
- }
-
- rc = of_property_read_u32_index(np, name, CPU0_PWR_ZONE_CTRL_REG,
- &cpu0_pwr_zone_ctrl_reg);
- if (rc) {
- pr_err("failed to read 1st entry from %s property (%d)\n", name,
- rc);
- rc = -EINVAL;
- goto cleanup;
- }
-
- rc = of_property_read_u32_index(np, name, CPU_RESET_CONFIG_REG,
- &cpu_rst_cfg_reg);
- if (rc) {
- pr_err("failed to read 2nd entry from %s property (%d)\n", name,
- rc);
- rc = -EINVAL;
- goto cleanup;
- }
-
-cleanup:
- if (syscon_np)
- of_node_put(syscon_np);
-
- return rc;
-}
-
-static int __init setup_hifcont_regs(struct device_node *np)
-{
- int rc = 0;
- char *name;
- struct device_node *syscon_np = NULL;
-
- name = "syscon-cont";
-
- syscon_np = of_parse_phandle(np, name, 0);
- if (!syscon_np) {
- pr_err("can't find phandle %s\n", name);
- rc = -EINVAL;
- goto cleanup;
- }
-
- hif_cont_block = of_iomap(syscon_np, 0);
- if (!hif_cont_block) {
- pr_err("iomap failed for hif_cont_block\n");
- rc = -EINVAL;
- goto cleanup;
- }
-
- /* offset is at top of hif_cont_block */
- hif_cont_reg = 0;
-
-cleanup:
- if (syscon_np)
- of_node_put(syscon_np);
-
- return rc;
-}
-
-static void __init brcmstb_cpu_ctrl_setup(unsigned int max_cpus)
-{
- int rc;
- struct device_node *np;
- char *name;
-
- name = "brcm,brcmstb-smpboot";
- np = of_find_compatible_node(NULL, NULL, name);
- if (!np) {
- pr_err("can't find compatible node %s\n", name);
- return;
- }
-
- rc = setup_hifcpubiuctrl_regs(np);
- if (rc)
- return;
-
- rc = setup_hifcont_regs(np);
- if (rc)
- return;
-}
-
-static DEFINE_SPINLOCK(boot_lock);
-
-static void brcmstb_secondary_init(unsigned int cpu)
-{
- /*
- * Synchronise with the boot thread.
- */
- spin_lock(&boot_lock);
- spin_unlock(&boot_lock);
-}
-
-static int brcmstb_boot_secondary(unsigned int cpu, struct task_struct *idle)
-{
- /*
- * set synchronisation state between this boot processor
- * and the secondary one
- */
- spin_lock(&boot_lock);
-
- /* Bring up power to the core if necessary */
- if (brcmstb_cpu_get_power_state(cpu) == 0)
- brcmstb_cpu_power_on(cpu);
-
- brcmstb_cpu_boot(cpu);
-
- /*
- * now the secondary core is starting up let it run its
- * calibrations, then wait for it to finish
- */
- spin_unlock(&boot_lock);
-
- return 0;
-}
-
-static struct smp_operations brcmstb_smp_ops __initdata = {
- .smp_prepare_cpus = brcmstb_cpu_ctrl_setup,
- .smp_secondary_init = brcmstb_secondary_init,
- .smp_boot_secondary = brcmstb_boot_secondary,
-#ifdef CONFIG_HOTPLUG_CPU
- .cpu_kill = brcmstb_cpu_kill,
- .cpu_die = brcmstb_cpu_die,
-#endif
-};
-
-CPU_METHOD_OF_DECLARE(brcmstb_smp, "brcm,brahma-b15", &brcmstb_smp_ops);
"mcr p15, 0, r0, c1, c0, 0 @ set SCTLR\n\t" \
"isb\n\t"\
"bl v7_flush_dcache_"__stringify(level)"\n\t" \
- "clrex\n\t"\
"mrc p15, 0, r0, c1, c0, 1 @ get ACTLR\n\t" \
"bic r0, r0, #(1 << 6) @ disable local coherency\n\t" \
/* Dummy Load of a device register to avoid Erratum 799270 */ \
board_nand_data.nr_parts = nr_parts;
board_nand_data.devsize = nand_type;
- board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_HW;
+ board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_SW;
gpmc_nand_init(&board_nand_data, gpmc_t);
}
#endif /* CONFIG_MTD_NAND_OMAP2 || CONFIG_MTD_NAND_OMAP2_MODULE */
return 0;
/* legacy platforms support only HAM1 (1-bit Hamming) ECC scheme */
- if (ecc_opt == OMAP_ECC_HAM1_CODE_HW)
+ if (ecc_opt == OMAP_ECC_HAM1_CODE_HW ||
+ ecc_opt == OMAP_ECC_HAM1_CODE_SW)
return 1;
else
return 0;
pr_err("%s: ti,nand-ecc-opt not found\n", __func__);
return -ENODEV;
}
- if (!strcmp(s, "ham1") || !strcmp(s, "sw") ||
- !strcmp(s, "hw") || !strcmp(s, "hw-romcode"))
+
+ if (!strcmp(s, "sw"))
+ gpmc_nand_data->ecc_opt = OMAP_ECC_HAM1_CODE_SW;
+ else if (!strcmp(s, "ham1") ||
+ !strcmp(s, "hw") || !strcmp(s, "hw-romcode"))
gpmc_nand_data->ecc_opt =
OMAP_ECC_HAM1_CODE_HW;
else if (!strcmp(s, "bch4"))
default:
/* Unknown default to latest silicon rev as default*/
- pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%d)\n",
+ pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%x)\n",
__func__, idcode, hawkeye, rev);
omap_revision = DRA752_REV_ES1_1;
}
r = clk_get_sys(dev_name(&od->pdev->dev), clk_alias);
if (!IS_ERR(r)) {
- dev_warn(&od->pdev->dev,
+ dev_dbg(&od->pdev->dev,
"alias %s already exists\n", clk_alias);
clk_put(r);
return;
oh->mux->pads_dynamic))) {
omap_hwmod_mux(oh->mux, _HWMOD_STATE_ENABLED);
_reconfigure_io_chain();
+ } else if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+ _reconfigure_io_chain();
}
_add_initiator_dep(oh, mpu_oh);
if (oh->mux && oh->mux->pads_dynamic) {
omap_hwmod_mux(oh->mux, _HWMOD_STATE_IDLE);
_reconfigure_io_chain();
+ } else if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+ _reconfigure_io_chain();
}
oh->_state = _HWMOD_STATE_IDLE;
if (!ois)
return 0;
+ if (ois[0] == NULL) /* Empty list */
+ return 0;
+
if (!linkspace) {
if (_alloc_linkspace(ois)) {
pr_err("omap_hwmod: could not allocate link space\n");
#include "i2c.h"
#include "mmc.h"
#include "wd_timer.h"
+#include "soc.h"
/* Base offset for all DRA7XX interrupts external to MPUSS */
#define DRA7XX_IRQ_GIC_START 32
&dra7xx_l4_per3__usb_otg_ss1,
&dra7xx_l4_per3__usb_otg_ss2,
&dra7xx_l4_per3__usb_otg_ss3,
- &dra7xx_l4_per3__usb_otg_ss4,
&dra7xx_l3_main_1__vcp1,
&dra7xx_l4_per2__vcp1,
&dra7xx_l3_main_1__vcp2,
NULL,
};
+static struct omap_hwmod_ocp_if *dra74x_hwmod_ocp_ifs[] __initdata = {
+ &dra7xx_l4_per3__usb_otg_ss4,
+ NULL,
+};
+
+static struct omap_hwmod_ocp_if *dra72x_hwmod_ocp_ifs[] __initdata = {
+ NULL,
+};
+
int __init dra7xx_hwmod_init(void)
{
+ int ret;
+
omap_hwmod_init();
- return omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs);
+ ret = omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs);
+
+ if (!ret && soc_is_dra74x())
+ return omap_hwmod_register_links(dra74x_hwmod_ocp_ifs);
+ else if (!ret && soc_is_dra72x())
+ return omap_hwmod_register_links(dra72x_hwmod_ocp_ifs);
+
+ return ret;
}
#define soc_is_omap54xx() 0
#define soc_is_omap543x() 0
#define soc_is_dra7xx() 0
+#define soc_is_dra74x() 0
+#define soc_is_dra72x() 0
#if defined(MULTI_OMAP2)
# if defined(CONFIG_ARCH_OMAP2)
#if defined(CONFIG_SOC_DRA7XX)
#undef soc_is_dra7xx
+#undef soc_is_dra74x
+#undef soc_is_dra72x
#define soc_is_dra7xx() (of_machine_is_compatible("ti,dra7"))
+#define soc_is_dra74x() (of_machine_is_compatible("ti,dra74"))
+#define soc_is_dra72x() (of_machine_is_compatible("ti,dra72"))
#endif
/* Various silicon revisions for omap2 */
static struct clk div4_clks[DIV4_NR] = {
[DIV4_SDH] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 8, 0x0dff, CLK_ENABLE_ON_INIT),
- [DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1de0, CLK_ENABLE_ON_INIT),
- [DIV4_SD1] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 0, 0x1de0, CLK_ENABLE_ON_INIT),
+ [DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1df0, CLK_ENABLE_ON_INIT),
+ [DIV4_SD1] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 0, 0x1df0, CLK_ENABLE_ON_INIT),
};
/* DIV6 clocks */
static struct clk div4_clks[DIV4_NR] = {
[DIV4_SDH] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 8, 0x0dff, CLK_ENABLE_ON_INIT),
- [DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1de0, CLK_ENABLE_ON_INIT),
+ [DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1df0, CLK_ENABLE_ON_INIT),
};
/* DIV6 clocks */
CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]), /* SCIFA5 */
CLKDEV_DEV_ID("e6cb0000.serial", &mstp_clks[MSTP207]), /* SCIFA5 */
CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP206]), /* SCIFB */
- CLKDEV_DEV_ID("0xe6c3000.serial", &mstp_clks[MSTP206]), /* SCIFB */
+ CLKDEV_DEV_ID("e6c3000.serial", &mstp_clks[MSTP206]), /* SCIFB */
CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */
CLKDEV_DEV_ID("e6c40000.serial", &mstp_clks[MSTP204]), /* SCIFA0 */
CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]), /* SCIFA1 */
static int ve_init_opp_table(struct device *cpu_dev)
{
- int cluster = topology_physical_package_id(cpu_dev->id);
- int idx, ret = 0, max_opp = info->num_opps[cluster];
- struct ve_spc_opp *opps = info->opps[cluster];
+ int cluster;
+ int idx, ret = 0, max_opp;
+ struct ve_spc_opp *opps;
+
+ cluster = topology_physical_package_id(cpu_dev->id);
+ cluster = cluster < 0 ? 0 : cluster;
+
+ max_opp = info->num_opps[cluster];
+ opps = info->opps[cluster];
for (idx = 0; idx < max_opp; idx++, opps++) {
ret = dev_pm_opp_add(cpu_dev, opps->freq * 1000, opps->u_volt);
spc->hw.init = &init;
spc->cluster = topology_physical_package_id(cpu_dev->id);
+ spc->cluster = spc->cluster < 0 ? 0 : spc->cluster;
+
init.name = dev_name(cpu_dev);
init.ops = &clk_spc_ops;
init.flags = CLK_IS_ROOT | CLK_GET_RATE_NOCACHE;
*/
.align 5
ENTRY(v6_early_abort)
-#ifdef CONFIG_CPU_V6
- sub r1, sp, #4 @ Get unused stack location
- strex r0, r1, [r1] @ Clear the exclusive monitor
-#elif defined(CONFIG_CPU_32v6K)
- clrex
-#endif
mrc p15, 0, r1, c5, c0, 0 @ get FSR
mrc p15, 0, r0, c6, c0, 0 @ get FAR
/*
*/
.align 5
ENTRY(v7_early_abort)
- /*
- * The effect of data aborts on on the exclusive access monitor are
- * UNPREDICTABLE. Do a CLREX to clear the state
- */
- clrex
-
mrc p15, 0, r1, c5, c0, 0 @ get FSR
mrc p15, 0, r0, c6, c0, 0 @ get FAR
kernel_neon_begin_partial(28);
sha2_ce_transform(blocks, data, sctx->state, NULL, len);
kernel_neon_end();
- data += blocks * SHA256_BLOCK_SIZE;
}
static int sha224_finup(struct shash_desc *desc, const u8 *data,
*/
#define ARM_MAX_BRP 16
#define ARM_MAX_WRP 16
-#define ARM_MAX_HBP_SLOTS (ARM_MAX_BRP + ARM_MAX_WRP)
/* Virtual debug register bases. */
#define AARCH64_DBG_REG_BVR 0
((struct pt_regs *)(THREAD_START_SP + task_stack_page(p)) - 1)
#define KSTK_EIP(tsk) ((unsigned long)task_pt_regs(tsk)->pc)
-#define KSTK_ESP(tsk) ((unsigned long)task_pt_regs(tsk)->sp)
+#define KSTK_ESP(tsk) user_stack_pointer(task_pt_regs(tsk))
/*
* Prefetching support
(!((regs)->pstate & PSR_F_BIT))
#define user_stack_pointer(regs) \
- (!compat_user_mode(regs)) ? ((regs)->sp) : ((regs)->compat_sp)
+ (!compat_user_mode(regs) ? (regs)->sp : (regs)->compat_sp)
static inline unsigned long regs_return_value(struct pt_regs *regs)
{
case CPU_PM_ENTER:
if (current->mm && !test_thread_flag(TIF_FOREIGN_FPSTATE))
fpsimd_save_state(¤t->thread.fpsimd_state);
+ this_cpu_write(fpsimd_last_state, NULL);
break;
case CPU_PM_EXIT:
if (current->mm)
.long 0
.popsection
- .align 3
-2: .quad .
- .quad PAGE_OFFSET
-
#ifdef CONFIG_SMP
.align 3
1: .quad .
return regs->compat_lr;
}
+ if ((u32)idx == PERF_REG_ARM64_SP)
+ return regs->sp;
+
+ if ((u32)idx == PERF_REG_ARM64_PC)
+ return regs->pc;
+
return regs->regs[idx];
}
break;
}
}
- for (i = ARM_MAX_BRP; i < ARM_MAX_HBP_SLOTS && !bp; ++i) {
+
+ for (i = 0; i < ARM_MAX_WRP; ++i) {
if (current->thread.debug.hbp_watch[i] == bp) {
info.si_errno = -((i << 1) + 1);
break;
kbuf += sizeof(reg);
} else {
ret = copy_to_user(ubuf, ®, sizeof(reg));
- if (ret)
+ if (ret) {
+ ret = -EFAULT;
break;
+ }
ubuf += sizeof(reg);
}
kbuf += sizeof(reg);
} else {
ret = copy_from_user(®, ubuf, sizeof(reg));
- if (ret)
- return ret;
+ if (ret) {
+ ret = -EFAULT;
+ break;
+ }
ubuf += sizeof(reg);
}
#endif
static const char *cpu_name;
+static const char *machine_name;
phys_addr_t __fdt_pointer __initdata;
/*
while (true)
cpu_relax();
}
+
+ machine_name = of_flat_dt_get_machine_name();
}
/*
{
int i;
- /*
- * Dump out the common processor features in a single line. Userspace
- * should read the hwcaps with getauxval(AT_HWCAP) rather than
- * attempting to parse this.
- */
- seq_puts(m, "features\t:");
- for (i = 0; hwcap_str[i]; i++)
- if (elf_hwcap & (1 << i))
- seq_printf(m, " %s", hwcap_str[i]);
- seq_puts(m, "\n\n");
+ seq_printf(m, "Processor\t: %s rev %d (%s)\n",
+ cpu_name, read_cpuid_id() & 15, ELF_PLATFORM);
for_each_online_cpu(i) {
- struct cpuinfo_arm64 *cpuinfo = &per_cpu(cpu_data, i);
- u32 midr = cpuinfo->reg_midr;
-
/*
* glibc reads /proc/cpuinfo to determine the number of
* online processors, looking for lines beginning with
#ifdef CONFIG_SMP
seq_printf(m, "processor\t: %d\n", i);
#endif
- seq_printf(m, "implementer\t: 0x%02x\n",
- MIDR_IMPLEMENTOR(midr));
- seq_printf(m, "variant\t\t: 0x%x\n", MIDR_VARIANT(midr));
- seq_printf(m, "partnum\t\t: 0x%03x\n", MIDR_PARTNUM(midr));
- seq_printf(m, "revision\t: 0x%x\n\n", MIDR_REVISION(midr));
}
+ /* dump out the processor features */
+ seq_puts(m, "Features\t: ");
+
+ for (i = 0; hwcap_str[i]; i++)
+ if (elf_hwcap & (1 << i))
+ seq_printf(m, "%s ", hwcap_str[i]);
+
+ seq_printf(m, "\nCPU implementer\t: 0x%02x\n", read_cpuid_id() >> 24);
+ seq_printf(m, "CPU architecture: AArch64\n");
+ seq_printf(m, "CPU variant\t: 0x%x\n", (read_cpuid_id() >> 20) & 15);
+ seq_printf(m, "CPU part\t: 0x%03x\n", (read_cpuid_id() >> 4) & 0xfff);
+ seq_printf(m, "CPU revision\t: %d\n", read_cpuid_id() & 15);
+
+ seq_puts(m, "\n");
+
+ seq_printf(m, "Hardware\t: %s\n", machine_name);
+
return 0;
}
);
local_irq_restore(flags);
}
+EXPORT_SYMBOL(flush_icache_range);
void hexagon_clean_dcache_range(unsigned long start, unsigned long end)
{
config KEXEC
bool "kexec system call"
depends on !IA64_HP_SIM && (!SMP || HOTPLUG_CPU)
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
config KEXEC
bool "kexec system call"
depends on M68KCLASSIC
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
config KEXEC
bool "Kexec system call"
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
config KEXEC
bool "kexec system call"
depends on (PPC_BOOK3S || FSL_BOOKE || (44x && !SMP))
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
config KEXEC
def_bool y
- select CRYPTO
- select CRYPTO_SHA256
config AUDIT_ARCH
def_bool y
#define __NR_sched_setattr 345
#define __NR_sched_getattr 346
#define __NR_renameat2 347
-#define NR_syscalls 348
+#define __NR_seccomp 348
+#define __NR_getrandom 349
+#define __NR_memfd_create 350
+#define NR_syscalls 351
/*
* There are some system calls that are not present on 64 bit, some
COMPAT_SYSCALL_WRAP3(sched_setattr, pid_t, pid, struct sched_attr __user *, attr, unsigned int, flags);
COMPAT_SYSCALL_WRAP4(sched_getattr, pid_t, pid, struct sched_attr __user *, attr, unsigned int, size, unsigned int, flags);
COMPAT_SYSCALL_WRAP5(renameat2, int, olddfd, const char __user *, oldname, int, newdfd, const char __user *, newname, unsigned int, flags);
+COMPAT_SYSCALL_WRAP3(seccomp, unsigned int, op, unsigned int, flags, const char __user *, uargs)
+COMPAT_SYSCALL_WRAP3(getrandom, char __user *, buf, size_t, count, unsigned int, flags)
+COMPAT_SYSCALL_WRAP2(memfd_create, const char __user *, uname, unsigned int, flags)
S390_lowcore.program_new_psw.addr =
PSW_ADDR_AMODE | (unsigned long) s390_base_pgm_handler;
+ /*
+ * Clear subchannel ID and number to signal new kernel that no CCW or
+ * SCSI IPL has been done (for kexec and kdump)
+ */
+ S390_lowcore.subchannel_id = 0;
+ S390_lowcore.subchannel_nr = 0;
+
/* Store status at absolute zero */
store_status();
#include <linux/stddef.h>
#include <linux/unistd.h>
#include <linux/ptrace.h>
+#include <linux/random.h>
#include <linux/user.h>
#include <linux/tty.h>
#include <linux/ioport.h>
#include <asm/diag.h>
#include <asm/os_info.h>
#include <asm/sclp.h>
+#include <asm/sysinfo.h>
#include "entry.h"
/*
#endif
get_cpu_id(&cpu_id);
+ add_device_randomness(&cpu_id, sizeof(cpu_id));
switch (cpu_id.machine) {
case 0x9672:
#if !defined(CONFIG_64BIT)
}
/*
+ * Add system information as device randomness
+ */
+static void __init setup_randomness(void)
+{
+ struct sysinfo_3_2_2 *vmms;
+
+ vmms = (struct sysinfo_3_2_2 *) alloc_page(GFP_KERNEL);
+ if (vmms && stsi(vmms, 3, 2, 2) == 0 && vmms->count)
+ add_device_randomness(&vmms, vmms->count);
+ free_page((unsigned long) vmms);
+}
+
+/*
* Setup function called from init/main.c just after the banner
* was printed.
*/
/* Setup zfcpdump support */
setup_zfcpdump();
+
+ /* Add system specific data to the random pool */
+ setup_randomness();
}
#ifdef CONFIG_32BIT
SYSCALL(sys_sched_setattr,sys_sched_setattr,compat_sys_sched_setattr) /* 345 */
SYSCALL(sys_sched_getattr,sys_sched_getattr,compat_sys_sched_getattr)
SYSCALL(sys_renameat2,sys_renameat2,compat_sys_renameat2)
+SYSCALL(sys_seccomp,sys_seccomp,compat_sys_seccomp)
+SYSCALL(sys_getrandom,sys_getrandom,compat_sys_getrandom)
+SYSCALL(sys_memfd_create,sys_memfd_create,compat_sys_memfd_create) /* 350 */
config KEXEC
bool "kexec system call (EXPERIMENTAL)"
depends on SUPERH32 && MMU
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
cacheop_on_each_cpu(local_flush_icache_range, (void *)&data, 1);
}
+EXPORT_SYMBOL(flush_icache_range);
void flush_icache_page(struct vm_area_struct *vma, struct page *page)
{
config KEXEC
bool "kexec system call"
- select CRYPTO
- select CRYPTO_SHA256
---help---
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
preempt_enable();
}
}
+EXPORT_SYMBOL(flush_icache_range);
/* Called when smp_send_reschedule() triggers IRQ_RESCHEDULE. */
err |= setup_sigframe(frame, regs, set);
if (err == 0)
- err |= setup_return(regs, &ksig->ka, frame->retcode, frame, usig);
+ err |= setup_return(regs, &ksig->ka, frame->retcode, frame,
+ ksig->sig);
return err;
}
err |= __save_altstack(&frame->sig.uc.uc_stack, regs->UCreg_sp);
err |= setup_sigframe(&frame->sig, regs, set);
if (err == 0)
- err |= setup_return(regs, &ksig->ka, frame->sig.retcode, frame, usig);
+ err |= setup_return(regs, &ksig->ka, frame->sig.retcode, frame,
+ ksig->sig);
if (err == 0) {
/*
int syscall)
{
struct thread_info *thread = current_thread_info();
- struct task_struct *tsk = current;
sigset_t *oldset = sigmask_to_save();
int usig = ksig->sig;
int ret;
if (!user_mode(regs))
return;
- if (get_signsl(&ksig)) {
+ if (get_signal(&ksig)) {
handle_signal(&ksig, regs, syscall);
return;
}
obj-y += platform/
obj-y += net/
-ifeq ($(CONFIG_X86_64),y)
-obj-$(CONFIG_KEXEC) += purgatory/
-endif
+obj-$(CONFIG_KEXEC_FILE) += purgatory/
config KEXEC
bool "kexec system call"
- select BUILD_BIN2C
- select CRYPTO
- select CRYPTO_SHA256
---help---
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
interface is strongly in flux, so no good recommendation can be
made.
+config KEXEC_FILE
+ bool "kexec file based system call"
+ select BUILD_BIN2C
+ depends on KEXEC
+ depends on X86_64
+ depends on CRYPTO=y
+ depends on CRYPTO_SHA256=y
+ ---help---
+ This is new version of kexec system call. This system call is
+ file based and takes file descriptors as system call argument
+ for kernel and initramfs as opposed to list of segments as
+ accepted by previous system call.
+
config KEXEC_VERIFY_SIG
bool "Verify kernel signature during kexec_file_load() syscall"
- depends on KEXEC
+ depends on KEXEC_FILE
---help---
This option makes kernel signature verification mandatory for
kexec_file_load() syscall. If kernel is signature can not be
$(Q)$(MAKE) $(build)=arch/x86/syscalls all
archprepare:
-ifeq ($(CONFIG_KEXEC),y)
-# Build only for 64bit. No loaders for 32bit yet.
- ifeq ($(CONFIG_X86_64),y)
+ifeq ($(CONFIG_KEXEC_FILE),y)
$(Q)$(MAKE) $(build)=arch/x86/purgatory arch/x86/purgatory/kexec-purgatory.c
- endif
endif
###
$(Q)rm -rf $(objtree)/arch/x86_64
$(Q)$(MAKE) $(clean)=$(boot)
$(Q)$(MAKE) $(clean)=arch/x86/tools
+ $(Q)$(MAKE) $(clean)=arch/x86/purgatory
PHONY += kvmconfig
kvmconfig:
extern void io_apic_eoi(unsigned int apic, unsigned int vector);
+extern bool mp_should_keep_irq(struct device *dev);
+
#else /* !CONFIG_X86_IO_APIC */
#define io_apic_assign_pci_irqs 0
static inline int pte_special(pte_t pte)
{
- return (pte_flags(pte) & (_PAGE_PRESENT|_PAGE_SPECIAL)) ==
- (_PAGE_PRESENT|_PAGE_SPECIAL);
+ /*
+ * See CONFIG_NUMA_BALANCING pte_numa in include/asm-generic/pgtable.h.
+ * On x86 we have _PAGE_BIT_NUMA == _PAGE_BIT_GLOBAL+1 ==
+ * __PAGE_BIT_SOFTW1 == _PAGE_BIT_SPECIAL.
+ */
+ return (pte_flags(pte) & _PAGE_SPECIAL) &&
+ (pte_flags(pte) & (_PAGE_PRESENT|_PAGE_PROTNONE));
}
static inline unsigned long pte_pfn(pte_t pte)
obj-$(CONFIG_X86_TSC) += trace_clock.o
obj-$(CONFIG_KEXEC) += machine_kexec_$(BITS).o
obj-$(CONFIG_KEXEC) += relocate_kernel_$(BITS).o crash.o
+obj-$(CONFIG_KEXEC_FILE) += kexec-bzimage64.o
obj-$(CONFIG_CRASH_DUMP) += crash_dump_$(BITS).o
obj-y += kprobes/
obj-$(CONFIG_MODULES) += module.o
obj-$(CONFIG_PCI_MMCONFIG) += mmconf-fam10h_64.o
obj-y += vsmp_64.o
- obj-$(CONFIG_KEXEC) += kexec-bzimage64.o
endif
}
if (flags & IOAPIC_MAP_ALLOC) {
+ /* special handling for legacy IRQs */
+ if (irq < nr_legacy_irqs() && info->count == 1 &&
+ mp_irqdomain_map(domain, irq, pin) != 0)
+ irq = -1;
+
if (irq > 0)
info->count++;
else if (info->count == 0)
info->polarity = 1;
}
info->node = NUMA_NO_NODE;
- info->set = 1;
+
+ /*
+ * setup_IO_APIC_irqs() programs all legacy IRQs with default
+ * trigger and polarity attributes. Don't set the flag for that
+ * case so the first legacy IRQ user could reprogram the pin
+ * with real trigger and polarity attributes.
+ */
+ if (virq >= nr_legacy_irqs() || info->count)
+ info->set = 1;
}
set_io_apic_irq_attr(&attr, ioapic, hwirq, info->trigger,
info->polarity);
return ret;
}
+bool mp_should_keep_irq(struct device *dev)
+{
+ if (dev->power.is_prepared)
+ return true;
+#ifdef CONFIG_PM_RUNTIME
+ if (dev->power.runtime_status == RPM_SUSPENDING)
+ return true;
+#endif
+
+ return false;
+}
+
/* Enable IOAPIC early just for system timer */
void __init pre_init_apic_IRQ0(void)
{
crash_save_cpu(regs, safe_smp_processor_id());
}
-#ifdef CONFIG_X86_64
-
+#ifdef CONFIG_KEXEC_FILE
static int get_nr_ram_ranges_callback(unsigned long start_pfn,
unsigned long nr_pfn, void *arg)
{
return ret;
}
-
-#endif /* CONFIG_X86_64 */
+#endif /* CONFIG_KEXEC_FILE */
set_intr_gate(i, interrupt[i - FIRST_EXTERNAL_VECTOR]);
}
- if (!acpi_ioapic && !of_ioapic)
+ if (!acpi_ioapic && !of_ioapic && nr_legacy_irqs())
setup_irq(2, &irq2);
#ifdef CONFIG_X86_32
#include <asm/debugreg.h>
#include <asm/kexec-bzimage64.h>
+#ifdef CONFIG_KEXEC_FILE
static struct kexec_file_ops *kexec_file_loaders[] = {
&kexec_bzImage64_ops,
};
+#endif
static void free_transition_pgtable(struct kimage *image)
{
);
}
+#ifdef CONFIG_KEXEC_FILE
/* Update purgatory as needed after various image segments have been prepared */
static int arch_update_purgatory(struct kimage *image)
{
return ret;
}
+#else /* !CONFIG_KEXEC_FILE */
+static inline int arch_update_purgatory(struct kimage *image)
+{
+ return 0;
+}
+#endif /* CONFIG_KEXEC_FILE */
int machine_kexec_prepare(struct kimage *image)
{
/* arch-dependent functionality related to kexec file-based syscall */
+#ifdef CONFIG_KEXEC_FILE
int arch_kexec_kernel_image_probe(struct kimage *image, void *buf,
unsigned long buf_len)
{
(int)ELF64_R_TYPE(rel[i].r_info), value);
return -ENOEXEC;
}
+#endif /* CONFIG_KEXEC_FILE */
void __init setup_default_timer_irq(void)
{
+ if (!nr_legacy_irqs())
+ return;
setup_irq(0, &irq0);
}
static void intel_mid_pci_irq_disable(struct pci_dev *dev)
{
- if (!dev->dev.power.is_prepared && dev->irq > 0)
+ if (!mp_should_keep_irq(&dev->dev) && dev->irq > 0)
mp_unmap_irq(dev->irq);
}
static void pirq_disable_irq(struct pci_dev *dev)
{
- if (io_apic_assign_pci_irqs && !dev->dev.power.is_prepared &&
+ if (io_apic_assign_pci_irqs && !mp_should_keep_irq(&dev->dev) &&
dev->irq) {
mp_unmap_irq(dev->irq);
dev->irq = 0;
# sure how to relocate those. Like kexec-tools, use custom flags.
KBUILD_CFLAGS := -fno-strict-aliasing -Wall -Wstrict-prototypes -fno-zero-initialized-in-bss -fno-builtin -ffreestanding -c -MD -Os -mcmodel=large
+KBUILD_CFLAGS += -m$(BITS)
$(obj)/purgatory.ro: $(PURGATORY_OBJS) FORCE
$(call if_changed,ld)
$(call if_changed,bin2c)
-# No loaders for 32bits yet.
-ifeq ($(CONFIG_X86_64),y)
- obj-$(CONFIG_KEXEC) += kexec-purgatory.o
-endif
+obj-$(CONFIG_KEXEC_FILE) += kexec-purgatory.o
config XTENSA
def_bool y
select ARCH_WANT_FRAME_POINTERS
- select HAVE_IDE
- select GENERIC_ATOMIC64
- select GENERIC_CLOCKEVENTS
- select VIRT_TO_BUS
- select GENERIC_IRQ_SHOW
- select GENERIC_SCHED_CLOCK
- select MODULES_USE_ELF_RELA
- select GENERIC_PCI_IOMAP
select ARCH_WANT_IPC_PARSE_VERSION
select ARCH_WANT_OPTIONAL_GPIOLIB
select BUILDTIME_EXTABLE_SORT
select CLONE_BACKWARDS
- select IRQ_DOMAIN
- select HAVE_OPROFILE
+ select COMMON_CLK
+ select GENERIC_ATOMIC64
+ select GENERIC_CLOCKEVENTS
+ select GENERIC_IRQ_SHOW
+ select GENERIC_PCI_IOMAP
+ select GENERIC_SCHED_CLOCK
select HAVE_FUNCTION_TRACER
select HAVE_IRQ_TIME_ACCOUNTING
+ select HAVE_OPROFILE
select HAVE_PERF_EVENTS
- select COMMON_CLK
+ select IRQ_DOMAIN
+ select MODULES_USE_ELF_RELA
+ select VIRT_TO_BUS
help
Xtensa processors are 32-bit RISC machines designed by Tensilica
primarily for embedded systems. These processors are both
def_bool y
config MMU
- def_bool n
+ bool
+ default n if !XTENSA_VARIANT_CUSTOM
+ default XTENSA_VARIANT_MMU if XTENSA_VARIANT_CUSTOM
config VARIANT_IRQ_SWITCH
def_bool n
select VARIANT_IRQ_SWITCH
select ARCH_REQUIRE_GPIOLIB
select XTENSA_CALIBRATE_CCOUNT
+
+config XTENSA_VARIANT_CUSTOM
+ bool "Custom Xtensa processor configuration"
+ select MAY_HAVE_SMP
+ select HAVE_XTENSA_GPIO32
+ help
+ Select this variant to use a custom Xtensa processor configuration.
+ You will be prompted for a processor variant CORENAME.
endchoice
+config XTENSA_VARIANT_CUSTOM_NAME
+ string "Xtensa Processor Custom Core Variant Name"
+ depends on XTENSA_VARIANT_CUSTOM
+ help
+ Provide the name of a custom Xtensa processor variant.
+ This CORENAME selects arch/xtensa/variant/CORENAME.
+ Dont forget you have to select MMU if you have one.
+
+config XTENSA_VARIANT_NAME
+ string
+ default "dc232b" if XTENSA_VARIANT_DC232B
+ default "dc233c" if XTENSA_VARIANT_DC233C
+ default "fsf" if XTENSA_VARIANT_FSF
+ default "s6000" if XTENSA_VARIANT_S6000
+ default XTENSA_VARIANT_CUSTOM_NAME if XTENSA_VARIANT_CUSTOM
+
+config XTENSA_VARIANT_MMU
+ bool "Core variant has a Full MMU (TLB, Pages, Protection, etc)"
+ depends on XTENSA_VARIANT_CUSTOM
+ default y
+ help
+ Build a Conventional Kernel with full MMU support,
+ ie: it supports a TLB with auto-loading, page protection.
+
config XTENSA_UNALIGNED_USER
bool "Unaligned memory access in use space"
help
Say N if you want to disable CPU hotplug.
-config MATH_EMULATION
- bool "Math emulation"
- help
- Can we use information of configuration file?
-
config INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
bool "Initialize Xtensa MMU inside the Linux kernel code"
+ depends on MMU
default y
help
Earlier version initialized the MMU in the exception vector
config HIGHMEM
bool "High Memory Support"
+ depends on MMU
help
Linux can use the full amount of RAM in the system by
default. However, the default MMUv2 setup only maps the
If unsure, say Y.
+config FAST_SYSCALL_XTENSA
+ bool "Enable fast atomic syscalls"
+ default n
+ help
+ fast_syscall_xtensa is a syscall that can make atomic operations
+ on UP kernel when processor has no s32c1i support.
+
+ This syscall is deprecated. It may have issues when called with
+ invalid arguments. It is provided only for backwards compatibility.
+ Only enable it if your userspace software requires it.
+
+ If unsure, say N.
+
+config FAST_SYSCALL_SPILL_REGISTERS
+ bool "Enable spill registers syscall"
+ default n
+ help
+ fast_syscall_spill_registers is a syscall that spills all active
+ register windows of a calling userspace task onto its stack.
+
+ This syscall is deprecated. It may have issues when called with
+ invalid arguments. It is provided only for backwards compatibility.
+ Only enable it if your userspace software requires it.
+
+ If unsure, say N.
+
endmenu
config XTENSA_CALIBRATE_CCOUNT
config XTENSA_PLATFORM_XT2000
bool "XT2000"
+ select HAVE_IDE
help
XT2000 is the name of Tensilica's feature-rich emulation platform.
This hardware is capable of running a full Linux distribution.
config XTENSA_PLATFORM_S6105
bool "S6105"
+ select HAVE_IDE
select SERIAL_CONSOLE
select NO_IOPORT_MAP
# for more details.
#
# Copyright (C) 2001 - 2005 Tensilica Inc.
+# Copyright (C) 2014 Cadence Design Systems Inc.
#
# This file is included by the global makefile so that you can add your own
# architecture-specific flags and dependencies. Remember to do have actions
# Core configuration.
# (Use VAR=<xtensa_config> to use another default compiler.)
-variant-$(CONFIG_XTENSA_VARIANT_FSF) := fsf
-variant-$(CONFIG_XTENSA_VARIANT_DC232B) := dc232b
-variant-$(CONFIG_XTENSA_VARIANT_DC233C) := dc233c
-variant-$(CONFIG_XTENSA_VARIANT_S6000) := s6000
-variant-$(CONFIG_XTENSA_VARIANT_LINUX_CUSTOM) := custom
+variant-y := $(patsubst "%",%,$(CONFIG_XTENSA_VARIANT_NAME))
VARIANT = $(variant-y)
export VARIANT
/ {
compatible = "cdns,xtensa-kc705";
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug memmap=0x38000000";
+ };
memory@0 {
device_type = "memory";
- reg = <0x00000000 0x08000000>;
+ reg = <0x00000000 0x38000000>;
};
};
CONFIG_MMU=y
# CONFIG_XTENSA_UNALIGNED_USER is not set
# CONFIG_PREEMPT is not set
-# CONFIG_MATH_EMULATION is not set
# CONFIG_HIGHMEM is not set
#
# CONFIG_XTENSA_VARIANT_S6000 is not set
# CONFIG_XTENSA_UNALIGNED_USER is not set
# CONFIG_PREEMPT is not set
-# CONFIG_MATH_EMULATION is not set
CONFIG_XTENSA_CALIBRATE_CCOUNT=y
CONFIG_SERIAL_CONSOLE=y
CONFIG_XTENSA_ISS_NETWORK=y
# EEPROM support
#
# CONFIG_EEPROM_93CX6 is not set
-CONFIG_HAVE_IDE=y
+# CONFIG_HAVE_IDE is not set
# CONFIG_IDE is not set
#
CONFIG_XTENSA_VARIANT_S6000=y
# CONFIG_XTENSA_UNALIGNED_USER is not set
CONFIG_PREEMPT=y
-# CONFIG_MATH_EMULATION is not set
# CONFIG_HIGHMEM is not set
CONFIG_XTENSA_CALIBRATE_CCOUNT=y
CONFIG_SERIAL_CONSOLE=y
* specials for cache aliasing:
*
* __flush_invalidate_dcache_page_alias(vaddr,paddr)
+ * __invalidate_dcache_page_alias(vaddr,paddr)
* __invalidate_icache_page_alias(vaddr,paddr)
*/
#if defined(CONFIG_MMU) && (DCACHE_WAY_SIZE > PAGE_SIZE)
extern void __flush_invalidate_dcache_page_alias(unsigned long, unsigned long);
+extern void __invalidate_dcache_page_alias(unsigned long, unsigned long);
#else
static inline void __flush_invalidate_dcache_page_alias(unsigned long virt,
unsigned long phys) { }
* Here we define all the compile-time 'special' virtual
* addresses. The point is to have a constant address at
* compile time, but to set the physical address only
- * in the boot process. We allocate these special addresses
- * from the end of the consistent memory region backwards.
+ * in the boot process. We allocate these special addresses
+ * from the start of the consistent memory region upwards.
* Also this lets us do fail-safe vmalloc(), we
* can guarantee that these special addresses and
* vmalloc()-ed addresses never overlap.
#ifdef CONFIG_HIGHMEM
/* reserved pte's for temporary kernel mappings */
FIX_KMAP_BEGIN,
- FIX_KMAP_END = FIX_KMAP_BEGIN + (KM_TYPE_NR * NR_CPUS) - 1,
+ FIX_KMAP_END = FIX_KMAP_BEGIN +
+ (KM_TYPE_NR * NR_CPUS * DCACHE_N_COLORS) - 1,
#endif
__end_of_fixed_addresses
};
#define FIXADDR_SIZE (__end_of_fixed_addresses << PAGE_SHIFT)
#define FIXADDR_START ((FIXADDR_TOP - FIXADDR_SIZE) & PMD_MASK)
-#include <asm-generic/fixmap.h>
+#define __fix_to_virt(x) (FIXADDR_START + ((x) << PAGE_SHIFT))
+#define __virt_to_fix(x) (((x) - FIXADDR_START) >> PAGE_SHIFT)
+
+#ifndef __ASSEMBLY__
+/*
+ * 'index to address' translation. If anyone tries to use the idx
+ * directly without translation, we catch the bug with a NULL-deference
+ * kernel oops. Illegal ranges of incoming indices are caught too.
+ */
+static __always_inline unsigned long fix_to_virt(const unsigned int idx)
+{
+ BUILD_BUG_ON(idx >= __end_of_fixed_addresses);
+ return __fix_to_virt(idx);
+}
+
+static inline unsigned long virt_to_fix(const unsigned long vaddr)
+{
+ BUG_ON(vaddr >= FIXADDR_TOP || vaddr < FIXADDR_START);
+ return __virt_to_fix(vaddr);
+}
+
+#endif
#define kmap_get_fixmap_pte(vaddr) \
pte_offset_kernel( \
#ifndef _XTENSA_HIGHMEM_H
#define _XTENSA_HIGHMEM_H
+#include <linux/wait.h>
#include <asm/cacheflush.h>
#include <asm/fixmap.h>
#include <asm/kmap_types.h>
#include <asm/pgtable.h>
-#define PKMAP_BASE (FIXADDR_START - PMD_SIZE)
-#define LAST_PKMAP PTRS_PER_PTE
+#define PKMAP_BASE ((FIXADDR_START - \
+ (LAST_PKMAP + 1) * PAGE_SIZE) & PMD_MASK)
+#define LAST_PKMAP (PTRS_PER_PTE * DCACHE_N_COLORS)
#define LAST_PKMAP_MASK (LAST_PKMAP - 1)
#define PKMAP_NR(virt) (((virt) - PKMAP_BASE) >> PAGE_SHIFT)
#define PKMAP_ADDR(nr) (PKMAP_BASE + ((nr) << PAGE_SHIFT))
#define kmap_prot PAGE_KERNEL
+#if DCACHE_WAY_SIZE > PAGE_SIZE
+#define get_pkmap_color get_pkmap_color
+static inline int get_pkmap_color(struct page *page)
+{
+ return DCACHE_ALIAS(page_to_phys(page));
+}
+
+extern unsigned int last_pkmap_nr_arr[];
+
+static inline unsigned int get_next_pkmap_nr(unsigned int color)
+{
+ last_pkmap_nr_arr[color] =
+ (last_pkmap_nr_arr[color] + DCACHE_N_COLORS) & LAST_PKMAP_MASK;
+ return last_pkmap_nr_arr[color] + color;
+}
+
+static inline int no_more_pkmaps(unsigned int pkmap_nr, unsigned int color)
+{
+ return pkmap_nr < DCACHE_N_COLORS;
+}
+
+static inline int get_pkmap_entries_count(unsigned int color)
+{
+ return LAST_PKMAP / DCACHE_N_COLORS;
+}
+
+extern wait_queue_head_t pkmap_map_wait_arr[];
+
+static inline wait_queue_head_t *get_pkmap_wait_queue_head(unsigned int color)
+{
+ return pkmap_map_wait_arr + color;
+}
+#endif
+
extern pte_t *pkmap_page_table;
void *kmap_high(struct page *page);
# define DCACHE_ALIAS_EQ(a,b) ((((a) ^ (b)) & DCACHE_ALIAS_MASK) == 0)
#else
# define DCACHE_ALIAS_ORDER 0
+# define DCACHE_ALIAS(a) ((void)(a), 0)
#endif
+#define DCACHE_N_COLORS (1 << DCACHE_ALIAS_ORDER)
#if ICACHE_WAY_SIZE > PAGE_SIZE
# define ICACHE_ALIAS_ORDER (ICACHE_WAY_SHIFT - PAGE_SHIFT)
#endif
struct page;
+struct vm_area_struct;
extern void clear_page(void *page);
extern void copy_page(void *to, void *from);
*/
#if DCACHE_WAY_SIZE > PAGE_SIZE
-extern void clear_user_page(void*, unsigned long, struct page*);
-extern void copy_user_page(void*, void*, unsigned long, struct page*);
+extern void clear_page_alias(void *vaddr, unsigned long paddr);
+extern void copy_page_alias(void *to, void *from,
+ unsigned long to_paddr, unsigned long from_paddr);
+
+#define clear_user_highpage clear_user_highpage
+void clear_user_highpage(struct page *page, unsigned long vaddr);
+#define __HAVE_ARCH_COPY_USER_HIGHPAGE
+void copy_user_highpage(struct page *to, struct page *from,
+ unsigned long vaddr, struct vm_area_struct *vma);
#else
# define clear_user_page(page, vaddr, pg) clear_page(page)
# define copy_user_page(to, from, vaddr, pg) copy_page(to, from)
#define VMALLOC_START 0xC0000000
#define VMALLOC_END 0xC7FEFFFF
#define TLBTEMP_BASE_1 0xC7FF0000
-#define TLBTEMP_BASE_2 0xC7FF8000
+#define TLBTEMP_BASE_2 (TLBTEMP_BASE_1 + DCACHE_WAY_SIZE)
+#if 2 * DCACHE_WAY_SIZE > ICACHE_WAY_SIZE
+#define TLBTEMP_SIZE (2 * DCACHE_WAY_SIZE)
+#else
+#define TLBTEMP_SIZE ICACHE_WAY_SIZE
+#endif
/*
* For the Xtensa architecture, the PTE layout is as follows:
*/
.macro get_fs ad, sp
GET_CURRENT(\ad,\sp)
+#if THREAD_CURRENT_DS > 1020
+ addi \ad, \ad, TASK_THREAD
+ l32i \ad, \ad, THREAD_CURRENT_DS - TASK_THREAD
+#else
l32i \ad, \ad, THREAD_CURRENT_DS
+#endif
.endm
/*
#define TCSETSW 0x5403
#define TCSETSF 0x5404
-#define TCGETA _IOR('t', 23, struct termio)
-#define TCSETA _IOW('t', 24, struct termio)
-#define TCSETAW _IOW('t', 25, struct termio)
-#define TCSETAF _IOW('t', 28, struct termio)
+#define TCGETA 0x80127417 /* _IOR('t', 23, struct termio) */
+#define TCSETA 0x40127418 /* _IOW('t', 24, struct termio) */
+#define TCSETAW 0x40127419 /* _IOW('t', 25, struct termio) */
+#define TCSETAF 0x4012741C /* _IOW('t', 28, struct termio) */
#define TCSBRK _IO('t', 29)
#define TCXONC _IO('t', 30)
#define TCFLSH _IO('t', 31)
-#define TIOCSWINSZ _IOW('t', 103, struct winsize)
-#define TIOCGWINSZ _IOR('t', 104, struct winsize)
+#define TIOCSWINSZ 0x40087467 /* _IOW('t', 103, struct winsize) */
+#define TIOCGWINSZ 0x80087468 /* _IOR('t', 104, struct winsize) */
#define TIOCSTART _IO('t', 110) /* start output, like ^Q */
#define TIOCSTOP _IO('t', 111) /* stop output, like ^S */
#define TIOCOUTQ _IOR('t', 115, int) /* output queue size */
#define TIOCSETD _IOW('T', 35, int)
#define TIOCGETD _IOR('T', 36, int)
#define TCSBRKP _IOW('T', 37, int) /* Needed for POSIX tcsendbreak()*/
-#define TIOCTTYGSTRUCT _IOR('T', 38, struct tty_struct) /* For debugging only*/
#define TIOCSBRK _IO('T', 39) /* BSD compatibility */
#define TIOCCBRK _IO('T', 40) /* BSD compatibility */
#define TIOCGSID _IOR('T', 41, pid_t) /* Return the session ID of FD*/
#define TIOCSERGETLSR _IOR('T', 89, unsigned int) /* Get line status reg. */
/* ioctl (fd, TIOCSERGETLSR, &result) where result may be as below */
# define TIOCSER_TEMT 0x01 /* Transmitter physically empty */
-#define TIOCSERGETMULTI _IOR('T', 90, struct serial_multiport_struct) /* Get multiport config */
-#define TIOCSERSETMULTI _IOW('T', 91, struct serial_multiport_struct) /* Set multiport config */
+#define TIOCSERGETMULTI 0x80a8545a /* Get multiport config */
+ /* _IOR('T', 90, struct serial_multiport_struct) */
+#define TIOCSERSETMULTI 0x40a8545b /* Set multiport config */
+ /* _IOW('T', 91, struct serial_multiport_struct) */
#define TIOCMIWAIT _IO('T', 92) /* wait for a change on serial input line(s) */
#define TIOCGICOUNT 0x545D /* read serial port inline interrupt counts */
#define __NR_sched_getattr 335
__SYSCALL(335, sys_sched_getattr, 3)
-#define __NR_syscall_count 336
+#define __NR_renameat2 336
+__SYSCALL(336, sys_renameat2, 5)
+
+#define __NR_syscall_count 337
/*
* sysxtensa syscall handler
* this archive for more details.
*
* Copyright (C) 2001 - 2005 Tensilica, Inc.
+ * Copyright (C) 2014 Cadence Design Systems Inc.
*
* Rewritten by Chris Zankel <chris@zankel.net>
*
s32i a0, a2, PT_AREG2
s32i a3, a2, PT_AREG3
+ rsr a3, excsave1
+ movi a4, fast_unaligned_fixup
+ s32i a4, a3, EXC_TABLE_FIXUP
+
/* Keep value of SAR in a0 */
rsr a0, sar
addx8 a5, a6, a5
jx a5 # jump into table
- /* Invalid instruction, CRITICAL! */
-.Linvalid_instruction_load:
- j .Linvalid_instruction
-
/* Load: Load memory address. */
.Lload: movi a3, ~3
/* Set target register. */
1:
-
-#if XCHAL_HAVE_LOOPS
- rsr a5, lend # check if we reached LEND
- bne a7, a5, 1f
- rsr a5, lcount # and LCOUNT != 0
- beqz a5, 1f
- addi a5, a5, -1 # decrement LCOUNT and set
- rsr a7, lbeg # set PC to LBEGIN
- wsr a5, lcount
-#endif
-
-1: wsr a7, epc1 # skip load instruction
extui a4, a4, INSN_T, 4 # extract target register
movi a5, .Lload_table
addx8 a4, a4, a5
mov a3, a14 ; _j 1f; .align 8
mov a3, a15 ; _j 1f; .align 8
+ /* We cannot handle this exception. */
+
+ .extern _kernel_exception
+.Linvalid_instruction_load:
+.Linvalid_instruction_store:
+
+ movi a4, 0
+ rsr a3, excsave1
+ s32i a4, a3, EXC_TABLE_FIXUP
+
+ /* Restore a4...a8 and SAR, set SP, and jump to default exception. */
+
+ l32i a8, a2, PT_AREG8
+ l32i a7, a2, PT_AREG7
+ l32i a6, a2, PT_AREG6
+ l32i a5, a2, PT_AREG5
+ l32i a4, a2, PT_AREG4
+ wsr a0, sar
+ mov a1, a2
+
+ rsr a0, ps
+ bbsi.l a0, PS_UM_BIT, 2f # jump if user mode
+
+ movi a0, _kernel_exception
+ jx a0
+
+2: movi a0, _user_exception
+ jx a0
+
1: # a7: instruction pointer, a4: instruction, a3: value
movi a6, 0 # mask: ffffffff:00000000
/* Get memory address */
1:
-#if XCHAL_HAVE_LOOPS
- rsr a4, lend # check if we reached LEND
- bne a7, a4, 1f
- rsr a4, lcount # and LCOUNT != 0
- beqz a4, 1f
- addi a4, a4, -1 # decrement LCOUNT and set
- rsr a7, lbeg # set PC to LBEGIN
- wsr a4, lcount
-#endif
-
-1: wsr a7, epc1 # skip store instruction
movi a4, ~3
and a4, a4, a8 # align memory address
#endif
__ssa8r a8
- __src_b a7, a5, a6 # lo-mask F..F0..0 (BE) 0..0F..F (LE)
+ __src_b a8, a5, a6 # lo-mask F..F0..0 (BE) 0..0F..F (LE)
__src_b a6, a6, a5 # hi-mask 0..0F..F (BE) F..F0..0 (LE)
#ifdef UNALIGNED_USER_EXCEPTION
l32e a5, a4, -8
#else
l32i a5, a4, 0 # load lower address word
#endif
- and a5, a5, a7 # mask
- __sh a7, a3 # shift value
- or a5, a5, a7 # or with original value
+ and a5, a5, a8 # mask
+ __sh a8, a3 # shift value
+ or a5, a5, a8 # or with original value
#ifdef UNALIGNED_USER_EXCEPTION
s32e a5, a4, -8
- l32e a7, a4, -4
+ l32e a8, a4, -4
#else
s32i a5, a4, 0 # store
- l32i a7, a4, 4 # same for upper address word
+ l32i a8, a4, 4 # same for upper address word
#endif
__sl a5, a3
- and a6, a7, a6
+ and a6, a8, a6
or a6, a6, a5
#ifdef UNALIGNED_USER_EXCEPTION
s32e a6, a4, -4
s32i a6, a4, 4
#endif
- /* Done. restore stack and return */
-
.Lexit:
+#if XCHAL_HAVE_LOOPS
+ rsr a4, lend # check if we reached LEND
+ bne a7, a4, 1f
+ rsr a4, lcount # and LCOUNT != 0
+ beqz a4, 1f
+ addi a4, a4, -1 # decrement LCOUNT and set
+ rsr a7, lbeg # set PC to LBEGIN
+ wsr a4, lcount
+#endif
+
+1: wsr a7, epc1 # skip emulated instruction
+
+ /* Update icount if we're single-stepping in userspace. */
+ rsr a4, icountlevel
+ beqz a4, 1f
+ bgeui a4, LOCKLEVEL + 1, 1f
+ rsr a4, icount
+ addi a4, a4, 1
+ wsr a4, icount
+1:
movi a4, 0
rsr a3, excsave1
s32i a4, a3, EXC_TABLE_FIXUP
l32i a2, a2, PT_AREG2
rfe
- /* We cannot handle this exception. */
+ENDPROC(fast_unaligned)
- .extern _kernel_exception
-.Linvalid_instruction_store:
-.Linvalid_instruction:
+ENTRY(fast_unaligned_fixup)
- /* Restore a4...a8 and SAR, set SP, and jump to default exception. */
+ l32i a2, a3, EXC_TABLE_DOUBLE_SAVE
+ wsr a3, excsave1
l32i a8, a2, PT_AREG8
l32i a7, a2, PT_AREG7
l32i a6, a2, PT_AREG6
l32i a5, a2, PT_AREG5
l32i a4, a2, PT_AREG4
+ l32i a0, a2, PT_AREG2
+ xsr a0, depc # restore depc and a0
wsr a0, sar
- mov a1, a2
+
+ rsr a0, exccause
+ s32i a0, a2, PT_DEPC # mark as a regular exception
rsr a0, ps
- bbsi.l a2, PS_UM_BIT, 1f # jump if user mode
+ bbsi.l a0, PS_UM_BIT, 1f # jump if user mode
- movi a0, _kernel_exception
+ rsr a0, exccause
+ addx4 a0, a0, a3 # find entry in table
+ l32i a0, a0, EXC_TABLE_FAST_KERNEL # load handler
+ l32i a3, a2, PT_AREG3
jx a0
-
-1: movi a0, _user_exception
+1:
+ rsr a0, exccause
+ addx4 a0, a0, a3 # find entry in table
+ l32i a0, a0, EXC_TABLE_FAST_USER # load handler
+ l32i a3, a2, PT_AREG3
jx a0
-ENDPROC(fast_unaligned)
+ENDPROC(fast_unaligned_fixup)
#endif /* XCHAL_UNALIGNED_LOAD_EXCEPTION || XCHAL_UNALIGNED_STORE_EXCEPTION */
* j done
*/
+#ifdef CONFIG_FAST_SYSCALL_XTENSA
+
#define TRY \
.section __ex_table, "a"; \
.word 66f, 67f; \
movi a7, 4 # sizeof(unsigned int)
access_ok a3, a7, a0, a2, .Leac # a0: scratch reg, a2: sp
- addi a6, a6, -1 # assuming SYS_XTENSA_ATOMIC_SET = 1
- _bgeui a6, SYS_XTENSA_COUNT - 1, .Lill
- _bnei a6, SYS_XTENSA_ATOMIC_CMP_SWP - 1, .Lnswp
+ _bgeui a6, SYS_XTENSA_COUNT, .Lill
+ _bnei a6, SYS_XTENSA_ATOMIC_CMP_SWP, .Lnswp
/* Fall through for ATOMIC_CMP_SWP. */
l32i a7, a2, PT_AREG7 # restore a7
l32i a0, a2, PT_AREG0 # restore a0
movi a2, 1 # and return 1
- addi a6, a6, 1 # restore a6 (really necessary?)
rfe
1: l32i a7, a2, PT_AREG7 # restore a7
l32i a0, a2, PT_AREG0 # restore a0
movi a2, 0 # return 0 (note that we cannot set
- addi a6, a6, 1 # restore a6 (really necessary?)
rfe
.Lnswp: /* Atomic set, add, and exg_add. */
TRY l32i a7, a3, 0 # orig
+ addi a6, a6, -SYS_XTENSA_ATOMIC_SET
add a0, a4, a7 # + arg
moveqz a0, a4, a6 # set
+ addi a6, a6, SYS_XTENSA_ATOMIC_SET
TRY s32i a0, a3, 0 # write new value
mov a0, a2
mov a2, a7
l32i a7, a0, PT_AREG7 # restore a7
l32i a0, a0, PT_AREG0 # restore a0
- addi a6, a6, 1 # restore a6 (really necessary?)
rfe
CATCH
movi a2, -EFAULT
rfe
-.Lill: l32i a7, a2, PT_AREG0 # restore a7
+.Lill: l32i a7, a2, PT_AREG7 # restore a7
l32i a0, a2, PT_AREG0 # restore a0
movi a2, -EINVAL
rfe
ENDPROC(fast_syscall_xtensa)
+#else /* CONFIG_FAST_SYSCALL_XTENSA */
+
+ENTRY(fast_syscall_xtensa)
+
+ l32i a0, a2, PT_AREG0 # restore a0
+ movi a2, -ENOSYS
+ rfe
+
+ENDPROC(fast_syscall_xtensa)
+
+#endif /* CONFIG_FAST_SYSCALL_XTENSA */
+
/* fast_syscall_spill_registers.
*
* Note: We assume the stack pointer is EXC_TABLE_KSTK in the fixup handler.
*/
+#ifdef CONFIG_FAST_SYSCALL_SPILL_REGISTERS
+
ENTRY(fast_syscall_spill_registers)
/* Register a FIXUP handler (pass current wb as a parameter) */
ENDPROC(fast_syscall_spill_registers_fixup_return)
+#else /* CONFIG_FAST_SYSCALL_SPILL_REGISTERS */
+
+ENTRY(fast_syscall_spill_registers)
+
+ l32i a0, a2, PT_AREG0 # restore a0
+ movi a2, -ENOSYS
+ rfe
+
+ENDPROC(fast_syscall_spill_registers)
+
+#endif /* CONFIG_FAST_SYSCALL_SPILL_REGISTERS */
+
#ifdef CONFIG_MMU
/*
* We should never get here. Bail out!
rsr a0, excvaddr
bltu a0, a3, 2f
- addi a1, a0, -(2 << (DCACHE_ALIAS_ORDER + PAGE_SHIFT))
+ addi a1, a0, -TLBTEMP_SIZE
bgeu a1, a3, 2f
/* Check if we have to restore an ITLB mapping. */
entry a1, 16
- mov a10, a2 # preserve 'prev' (a2)
mov a11, a3 # and 'next' (a3)
l32i a4, a2, TASK_THREAD_INFO
save_xtregs_user a4 a6 a8 a9 a12 a13 THREAD_XTREGS_USER
- s32i a0, a10, THREAD_RA # save return address
- s32i a1, a10, THREAD_SP # save stack pointer
+#if THREAD_RA > 1020 || THREAD_SP > 1020
+ addi a10, a2, TASK_THREAD
+ s32i a0, a10, THREAD_RA - TASK_THREAD # save return address
+ s32i a1, a10, THREAD_SP - TASK_THREAD # save stack pointer
+#else
+ s32i a0, a2, THREAD_RA # save return address
+ s32i a1, a2, THREAD_SP # save stack pointer
+#endif
/* Disable ints while we manipulate the stack pointer. */
load_xtregs_user a5 a6 a8 a9 a12 a13 THREAD_XTREGS_USER
wsr a14, ps
- mov a2, a10 # return 'prev'
rsync
retw
/* We currently don't support coherent memory outside KSEG */
- if (ret < XCHAL_KSEG_CACHED_VADDR
- || ret >= XCHAL_KSEG_CACHED_VADDR + XCHAL_KSEG_SIZE)
- BUG();
+ BUG_ON(ret < XCHAL_KSEG_CACHED_VADDR ||
+ ret > XCHAL_KSEG_CACHED_VADDR + XCHAL_KSEG_SIZE - 1);
if (ret != 0) {
void dma_free_coherent(struct device *hwdev, size_t size,
void *vaddr, dma_addr_t dma_handle)
{
- long addr=(long)vaddr+XCHAL_KSEG_CACHED_VADDR-XCHAL_KSEG_BYPASS_VADDR;
+ unsigned long addr = (unsigned long)vaddr +
+ XCHAL_KSEG_CACHED_VADDR - XCHAL_KSEG_BYPASS_VADDR;
- if (addr < 0 || addr >= XCHAL_KSEG_SIZE)
- BUG();
+ BUG_ON(addr < XCHAL_KSEG_CACHED_VADDR ||
+ addr > XCHAL_KSEG_CACHED_VADDR + XCHAL_KSEG_SIZE - 1);
free_pages(addr, get_order(size));
}
};
on_each_cpu(ipi_flush_icache_range, &fd, 1);
}
+EXPORT_SYMBOL(flush_icache_range);
/* ------------------------------------------------------------------------- */
#if XCHAL_UNALIGNED_LOAD_EXCEPTION || XCHAL_UNALIGNED_STORE_EXCEPTION
#ifdef CONFIG_XTENSA_UNALIGNED_USER
{ EXCCAUSE_UNALIGNED, USER, fast_unaligned },
-#else
-{ EXCCAUSE_UNALIGNED, 0, do_unaligned_user },
#endif
+{ EXCCAUSE_UNALIGNED, 0, do_unaligned_user },
{ EXCCAUSE_UNALIGNED, KRNL, fast_unaligned },
#endif
#ifdef CONFIG_MMU
*/
#if XCHAL_UNALIGNED_LOAD_EXCEPTION || XCHAL_UNALIGNED_STORE_EXCEPTION
-#ifndef CONFIG_XTENSA_UNALIGNED_USER
void
do_unaligned_user (struct pt_regs *regs)
{
}
#endif
-#endif
void
do_debug(struct pt_regs *regs)
s32i a0, a2, PT_DEPC
_DoubleExceptionVector_handle_exception:
+ addi a0, a0, -EXCCAUSE_UNALIGNED
+ beqz a0, 2f
addx4 a0, a0, a3
- l32i a0, a0, EXC_TABLE_FAST_USER
+ l32i a0, a0, EXC_TABLE_FAST_USER + 4 * EXCCAUSE_UNALIGNED
+ xsr a3, excsave1
+ jx a0
+2:
+ movi a0, user_exception
xsr a3, excsave1
jx a0
.UserExceptionVector.literal)
SECTION_VECTOR (_DoubleExceptionVector_literal,
.DoubleExceptionVector.literal,
- DOUBLEEXC_VECTOR_VADDR - 40,
+ DOUBLEEXC_VECTOR_VADDR - 48,
SIZEOF(.UserExceptionVector.text),
.UserExceptionVector.text)
SECTION_VECTOR (_DoubleExceptionVector_text,
.DoubleExceptionVector.text,
DOUBLEEXC_VECTOR_VADDR,
- 40,
+ 48,
.DoubleExceptionVector.literal)
. = (LOADADDR( .DoubleExceptionVector.text ) + SIZEOF( .DoubleExceptionVector.text ) + 3) & ~ 3;
*
*/
-#if (DCACHE_WAY_SIZE > PAGE_SIZE) && defined(CONFIG_HIGHMEM)
-#error "HIGHMEM is not supported on cores with aliasing cache."
-#endif
+#if (DCACHE_WAY_SIZE > PAGE_SIZE)
+static inline void kmap_invalidate_coherent(struct page *page,
+ unsigned long vaddr)
+{
+ if (!DCACHE_ALIAS_EQ(page_to_phys(page), vaddr)) {
+ unsigned long kvaddr;
+
+ if (!PageHighMem(page)) {
+ kvaddr = (unsigned long)page_to_virt(page);
+
+ __invalidate_dcache_page(kvaddr);
+ } else {
+ kvaddr = TLBTEMP_BASE_1 +
+ (page_to_phys(page) & DCACHE_ALIAS_MASK);
+
+ __invalidate_dcache_page_alias(kvaddr,
+ page_to_phys(page));
+ }
+ }
+}
+
+static inline void *coherent_kvaddr(struct page *page, unsigned long base,
+ unsigned long vaddr, unsigned long *paddr)
+{
+ if (PageHighMem(page) || !DCACHE_ALIAS_EQ(page_to_phys(page), vaddr)) {
+ *paddr = page_to_phys(page);
+ return (void *)(base + (vaddr & DCACHE_ALIAS_MASK));
+ } else {
+ *paddr = 0;
+ return page_to_virt(page);
+ }
+}
+
+void clear_user_highpage(struct page *page, unsigned long vaddr)
+{
+ unsigned long paddr;
+ void *kvaddr = coherent_kvaddr(page, TLBTEMP_BASE_1, vaddr, &paddr);
+
+ pagefault_disable();
+ kmap_invalidate_coherent(page, vaddr);
+ set_bit(PG_arch_1, &page->flags);
+ clear_page_alias(kvaddr, paddr);
+ pagefault_enable();
+}
+
+void copy_user_highpage(struct page *dst, struct page *src,
+ unsigned long vaddr, struct vm_area_struct *vma)
+{
+ unsigned long dst_paddr, src_paddr;
+ void *dst_vaddr = coherent_kvaddr(dst, TLBTEMP_BASE_1, vaddr,
+ &dst_paddr);
+ void *src_vaddr = coherent_kvaddr(src, TLBTEMP_BASE_2, vaddr,
+ &src_paddr);
+
+ pagefault_disable();
+ kmap_invalidate_coherent(dst, vaddr);
+ set_bit(PG_arch_1, &dst->flags);
+ copy_page_alias(dst_vaddr, src_vaddr, dst_paddr, src_paddr);
+ pagefault_enable();
+}
+
+#endif /* DCACHE_WAY_SIZE > PAGE_SIZE */
#if (DCACHE_WAY_SIZE > PAGE_SIZE) && XCHAL_DCACHE_IS_WRITEBACK
if (!alias && !mapping)
return;
- __flush_invalidate_dcache_page((long)page_address(page));
+ virt = TLBTEMP_BASE_1 + (phys & DCACHE_ALIAS_MASK);
+ __flush_invalidate_dcache_page_alias(virt, phys);
virt = TLBTEMP_BASE_1 + (temp & DCACHE_ALIAS_MASK);
#if (DCACHE_WAY_SIZE > PAGE_SIZE) && XCHAL_DCACHE_IS_WRITEBACK
if (!PageReserved(page) && test_bit(PG_arch_1, &page->flags)) {
-
- unsigned long paddr = (unsigned long) page_address(page);
unsigned long phys = page_to_phys(page);
- unsigned long tmp = TLBTEMP_BASE_1 + (addr & DCACHE_ALIAS_MASK);
-
- __flush_invalidate_dcache_page(paddr);
+ unsigned long tmp;
+ tmp = TLBTEMP_BASE_1 + (phys & DCACHE_ALIAS_MASK);
+ __flush_invalidate_dcache_page_alias(tmp, phys);
+ tmp = TLBTEMP_BASE_1 + (addr & DCACHE_ALIAS_MASK);
__flush_invalidate_dcache_page_alias(tmp, phys);
__invalidate_icache_page_alias(tmp, phys);
static pte_t *kmap_pte;
+#if DCACHE_WAY_SIZE > PAGE_SIZE
+unsigned int last_pkmap_nr_arr[DCACHE_N_COLORS];
+wait_queue_head_t pkmap_map_wait_arr[DCACHE_N_COLORS];
+
+static void __init kmap_waitqueues_init(void)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(pkmap_map_wait_arr); ++i)
+ init_waitqueue_head(pkmap_map_wait_arr + i);
+}
+#else
+static inline void kmap_waitqueues_init(void)
+{
+}
+#endif
+
+static inline enum fixed_addresses kmap_idx(int type, unsigned long color)
+{
+ return (type + KM_TYPE_NR * smp_processor_id()) * DCACHE_N_COLORS +
+ color;
+}
+
void *kmap_atomic(struct page *page)
{
enum fixed_addresses idx;
unsigned long vaddr;
- int type;
pagefault_disable();
if (!PageHighMem(page))
return page_address(page);
- type = kmap_atomic_idx_push();
- idx = type + KM_TYPE_NR * smp_processor_id();
+ idx = kmap_idx(kmap_atomic_idx_push(),
+ DCACHE_ALIAS(page_to_phys(page)));
vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx);
#ifdef CONFIG_DEBUG_HIGHMEM
- BUG_ON(!pte_none(*(kmap_pte - idx)));
+ BUG_ON(!pte_none(*(kmap_pte + idx)));
#endif
- set_pte(kmap_pte - idx, mk_pte(page, PAGE_KERNEL_EXEC));
+ set_pte(kmap_pte + idx, mk_pte(page, PAGE_KERNEL_EXEC));
return (void *)vaddr;
}
void __kunmap_atomic(void *kvaddr)
{
- int idx, type;
-
if (kvaddr >= (void *)FIXADDR_START &&
kvaddr < (void *)FIXADDR_TOP) {
- type = kmap_atomic_idx();
- idx = type + KM_TYPE_NR * smp_processor_id();
+ int idx = kmap_idx(kmap_atomic_idx(),
+ DCACHE_ALIAS((unsigned long)kvaddr));
/*
* Force other mappings to Oops if they'll try to access this
* is a bad idea also, in case the page changes cacheability
* attributes or becomes a protected page in a hypervisor.
*/
- pte_clear(&init_mm, kvaddr, kmap_pte - idx);
+ pte_clear(&init_mm, kvaddr, kmap_pte + idx);
local_flush_tlb_kernel_range((unsigned long)kvaddr,
(unsigned long)kvaddr + PAGE_SIZE);
/* cache the first kmap pte */
kmap_vstart = __fix_to_virt(FIX_KMAP_BEGIN);
kmap_pte = kmap_get_fixmap_pte(kmap_vstart);
+ kmap_waitqueues_init();
}
#if (DCACHE_WAY_SIZE > PAGE_SIZE)
/*
- * clear_user_page (void *addr, unsigned long vaddr, struct page *page)
- * a2 a3 a4
+ * clear_page_alias(void *addr, unsigned long paddr)
+ * a2 a3
*/
-ENTRY(clear_user_page)
+ENTRY(clear_page_alias)
entry a1, 32
- /* Mark page dirty and determine alias. */
+ /* Skip setting up a temporary DTLB if not aliased low page. */
- movi a7, (1 << PG_ARCH_1)
- l32i a5, a4, PAGE_FLAGS
- xor a6, a2, a3
- extui a3, a3, PAGE_SHIFT, DCACHE_ALIAS_ORDER
- extui a6, a6, PAGE_SHIFT, DCACHE_ALIAS_ORDER
- or a5, a5, a7
- slli a3, a3, PAGE_SHIFT
- s32i a5, a4, PAGE_FLAGS
+ movi a5, PAGE_OFFSET
+ movi a6, 0
+ beqz a3, 1f
- /* Skip setting up a temporary DTLB if not aliased. */
-
- beqz a6, 1f
-
- /* Invalidate kernel page. */
-
- mov a10, a2
- call8 __invalidate_dcache_page
-
- /* Setup a temporary DTLB with the color of the VPN */
-
- movi a4, ((PAGE_KERNEL | _PAGE_HW_WRITE) - PAGE_OFFSET) & 0xffffffff
- movi a5, TLBTEMP_BASE_1 # virt
- add a6, a2, a4 # ppn
- add a2, a5, a3 # add 'color'
+ /* Setup a temporary DTLB for the addr. */
+ addi a6, a3, (PAGE_KERNEL | _PAGE_HW_WRITE)
+ mov a4, a2
wdtlb a6, a2
dsync
/* We need to invalidate the temporary idtlb entry, if any. */
-1: addi a2, a2, -PAGE_SIZE
- idtlb a2
+1: idtlb a4
dsync
retw
-ENDPROC(clear_user_page)
+ENDPROC(clear_page_alias)
/*
- * copy_page_user (void *to, void *from, unsigned long vaddr, struct page *page)
- * a2 a3 a4 a5
+ * copy_page_alias(void *to, void *from,
+ * a2 a3
+ * unsigned long to_paddr, unsigned long from_paddr)
+ * a4 a5
*/
-ENTRY(copy_user_page)
+ENTRY(copy_page_alias)
entry a1, 32
- /* Mark page dirty and determine alias for destination. */
-
- movi a8, (1 << PG_ARCH_1)
- l32i a9, a5, PAGE_FLAGS
- xor a6, a2, a4
- xor a7, a3, a4
- extui a4, a4, PAGE_SHIFT, DCACHE_ALIAS_ORDER
- extui a6, a6, PAGE_SHIFT, DCACHE_ALIAS_ORDER
- extui a7, a7, PAGE_SHIFT, DCACHE_ALIAS_ORDER
- or a9, a9, a8
- slli a4, a4, PAGE_SHIFT
- s32i a9, a5, PAGE_FLAGS
- movi a5, ((PAGE_KERNEL | _PAGE_HW_WRITE) - PAGE_OFFSET) & 0xffffffff
-
- beqz a6, 1f
-
- /* Invalidate dcache */
-
- mov a10, a2
- call8 __invalidate_dcache_page
+ /* Skip setting up a temporary DTLB for destination if not aliased. */
- /* Setup a temporary DTLB with a matching color. */
+ movi a6, 0
+ movi a7, 0
+ beqz a4, 1f
- movi a8, TLBTEMP_BASE_1 # base
- add a6, a2, a5 # ppn
- add a2, a8, a4 # add 'color'
+ /* Setup a temporary DTLB for destination. */
+ addi a6, a4, (PAGE_KERNEL | _PAGE_HW_WRITE)
wdtlb a6, a2
dsync
- /* Skip setting up a temporary DTLB for destination if not aliased. */
+ /* Skip setting up a temporary DTLB for source if not aliased. */
-1: beqz a7, 1f
+1: beqz a5, 1f
- /* Setup a temporary DTLB with a matching color. */
+ /* Setup a temporary DTLB for source. */
- movi a8, TLBTEMP_BASE_2 # base
- add a7, a3, a5 # ppn
- add a3, a8, a4
+ addi a7, a5, PAGE_KERNEL
addi a8, a3, 1 # way1
wdtlb a7, a8
retw
-ENDPROC(copy_user_page)
+ENDPROC(copy_page_alias)
#endif
retw
ENDPROC(__flush_invalidate_dcache_page_alias)
+
+/*
+ * void __invalidate_dcache_page_alias (addr, phys)
+ * a2 a3
+ */
+
+ENTRY(__invalidate_dcache_page_alias)
+
+ entry sp, 16
+
+ movi a7, 0 # required for exception handler
+ addi a6, a3, (PAGE_KERNEL | _PAGE_HW_WRITE)
+ mov a4, a2
+ wdtlb a6, a2
+ dsync
+
+ ___invalidate_dcache_page a2 a3
+
+ idtlb a4
+ dsync
+
+ retw
+
+ENDPROC(__invalidate_dcache_page_alias)
#endif
ENTRY(__tlbtemp_mapping_itlb)
#include <asm/io.h>
#if defined(CONFIG_HIGHMEM)
-static void * __init init_pmd(unsigned long vaddr)
+static void * __init init_pmd(unsigned long vaddr, unsigned long n_pages)
{
pgd_t *pgd = pgd_offset_k(vaddr);
pmd_t *pmd = pmd_offset(pgd, vaddr);
+ pte_t *pte;
+ unsigned long i;
- if (pmd_none(*pmd)) {
- unsigned i;
- pte_t *pte = alloc_bootmem_low_pages(PAGE_SIZE);
+ n_pages = ALIGN(n_pages, PTRS_PER_PTE);
- for (i = 0; i < 1024; i++)
- pte_clear(NULL, 0, pte + i);
+ pr_debug("%s: vaddr: 0x%08lx, n_pages: %ld\n",
+ __func__, vaddr, n_pages);
- set_pmd(pmd, __pmd(((unsigned long)pte) & PAGE_MASK));
- BUG_ON(pte != pte_offset_kernel(pmd, 0));
- pr_debug("%s: vaddr: 0x%08lx, pmd: 0x%p, pte: 0x%p\n",
- __func__, vaddr, pmd, pte);
- return pte;
- } else {
- return pte_offset_kernel(pmd, 0);
+ pte = alloc_bootmem_low_pages(n_pages * sizeof(pte_t));
+
+ for (i = 0; i < n_pages; ++i)
+ pte_clear(NULL, 0, pte + i);
+
+ for (i = 0; i < n_pages; i += PTRS_PER_PTE, ++pmd) {
+ pte_t *cur_pte = pte + i;
+
+ BUG_ON(!pmd_none(*pmd));
+ set_pmd(pmd, __pmd(((unsigned long)cur_pte) & PAGE_MASK));
+ BUG_ON(cur_pte != pte_offset_kernel(pmd, 0));
+ pr_debug("%s: pmd: 0x%p, pte: 0x%p\n",
+ __func__, pmd, cur_pte);
}
+ return pte;
}
static void __init fixedrange_init(void)
{
- BUILD_BUG_ON(FIXADDR_SIZE > PMD_SIZE);
- init_pmd(__fix_to_virt(__end_of_fixed_addresses - 1) & PMD_MASK);
+ init_pmd(__fix_to_virt(0), __end_of_fixed_addresses);
}
#endif
memset(swapper_pg_dir, 0, PAGE_SIZE);
#ifdef CONFIG_HIGHMEM
fixedrange_init();
- pkmap_page_table = init_pmd(PKMAP_BASE);
+ pkmap_page_table = init_pmd(PKMAP_BASE, LAST_PKMAP);
kmap_init();
#endif
}
*/
if (error) {
bio->bi_end_io = bip->bip_end_io;
- bio_endio(bio, error);
+ bio_endio_nodec(bio, error);
return;
}
rq->__sector = (sector_t) -1;
rq->bio = rq->biotail = NULL;
memset(rq->__cmd, 0, sizeof(rq->__cmd));
- rq->cmd = rq->__cmd;
}
EXPORT_SYMBOL(blk_rq_set_block_pc);
*/
void blk_mq_freeze_queue(struct request_queue *q)
{
+ bool freeze;
+
spin_lock_irq(q->queue_lock);
- q->mq_freeze_depth++;
+ freeze = !q->mq_freeze_depth++;
spin_unlock_irq(q->queue_lock);
- percpu_ref_kill(&q->mq_usage_counter);
- blk_mq_run_queues(q, false);
+ if (freeze) {
+ percpu_ref_kill(&q->mq_usage_counter);
+ blk_mq_run_queues(q, false);
+ }
wait_event(q->mq_freeze_wq, percpu_ref_is_zero(&q->mq_usage_counter));
}
static void blk_mq_unfreeze_queue(struct request_queue *q)
{
- bool wake = false;
+ bool wake;
spin_lock_irq(q->queue_lock);
wake = !--q->mq_freeze_depth;
/* tag was already set */
rq->errors = 0;
+ rq->cmd = rq->__cmd;
+
rq->extra_len = 0;
rq->sense_len = 0;
rq->resid_len = 0;
blk_account_io_start(rq, 1);
}
+static inline bool hctx_allow_merges(struct blk_mq_hw_ctx *hctx)
+{
+ return (hctx->flags & BLK_MQ_F_SHOULD_MERGE) &&
+ !blk_queue_nomerges(hctx->queue);
+}
+
static inline bool blk_mq_merge_queue_io(struct blk_mq_hw_ctx *hctx,
struct blk_mq_ctx *ctx,
struct request *rq, struct bio *bio)
{
- struct request_queue *q = hctx->queue;
-
- if (!(hctx->flags & BLK_MQ_F_SHOULD_MERGE)) {
+ if (!hctx_allow_merges(hctx)) {
blk_mq_bio_to_request(rq, bio);
spin_lock(&ctx->lock);
insert_rq:
spin_unlock(&ctx->lock);
return false;
} else {
+ struct request_queue *q = hctx->queue;
+
spin_lock(&ctx->lock);
if (!blk_mq_attempt_merge(q, ctx, bio)) {
blk_mq_bio_to_request(rq, bio);
hctx->tags = set->tags[i];
/*
- * Allocate space for all possible cpus to avoid allocation in
+ * Allocate space for all possible cpus to avoid allocation at
* runtime
*/
hctx->ctxs = kmalloc_node(nr_cpu_ids * sizeof(void *),
queue_for_each_hw_ctx(q, hctx, i) {
/*
- * If not software queues are mapped to this hardware queue,
- * disable it and free the request entries
+ * If no software queues are mapped to this hardware queue,
+ * disable it and free the request entries.
*/
if (!hctx->nr_ctx) {
struct blk_mq_tag_set *set = q->tag_set;
{
struct blk_mq_tag_set *set = q->tag_set;
- blk_mq_freeze_queue(q);
-
mutex_lock(&set->tag_list_lock);
list_del_init(&q->tag_set_list);
blk_mq_update_tag_set_depth(set);
mutex_unlock(&set->tag_list_lock);
-
- blk_mq_unfreeze_queue(q);
}
static void blk_mq_add_queue_tag_set(struct blk_mq_tag_set *set,
rb_insert_color(&cfqg->rb_node, &st->rb);
}
+/*
+ * This has to be called only on activation of cfqg
+ */
static void
cfq_update_group_weight(struct cfq_group *cfqg)
{
- BUG_ON(!RB_EMPTY_NODE(&cfqg->rb_node));
-
if (cfqg->new_weight) {
cfqg->weight = cfqg->new_weight;
cfqg->new_weight = 0;
}
+}
+
+static void
+cfq_update_group_leaf_weight(struct cfq_group *cfqg)
+{
+ BUG_ON(!RB_EMPTY_NODE(&cfqg->rb_node));
if (cfqg->new_leaf_weight) {
cfqg->leaf_weight = cfqg->new_leaf_weight;
/* add to the service tree */
BUG_ON(!RB_EMPTY_NODE(&cfqg->rb_node));
- cfq_update_group_weight(cfqg);
+ /*
+ * Update leaf_weight. We cannot update weight at this point
+ * because cfqg might already have been activated and is
+ * contributing its current weight to the parent's child_weight.
+ */
+ cfq_update_group_leaf_weight(cfqg);
__cfq_group_service_tree_add(st, cfqg);
/*
*/
while ((parent = cfqg_parent(pos))) {
if (propagate) {
+ cfq_update_group_weight(pos);
propagate = !parent->nr_active++;
parent->children_weight += pos->weight;
}
r = blk_rq_unmap_user(bio);
if (!ret)
ret = r;
- blk_put_request(rq);
return ret;
}
if (hdr->interface_id != 'S')
return -EINVAL;
- if (hdr->cmd_len > BLK_MAX_CDB)
- return -EINVAL;
if (hdr->dxfer_len > (queue_max_hw_sectors(q) << 9))
return -EIO;
if (hdr->flags & SG_FLAG_Q_AT_HEAD)
at_head = 1;
+ ret = -ENOMEM;
rq = blk_get_request(q, writing ? WRITE : READ, GFP_KERNEL);
if (!rq)
- return -ENOMEM;
+ goto out;
blk_rq_set_block_pc(rq);
- if (blk_fill_sghdr_rq(q, rq, hdr, mode)) {
- blk_put_request(rq);
- return -EFAULT;
+ if (hdr->cmd_len > BLK_MAX_CDB) {
+ rq->cmd = kzalloc(hdr->cmd_len, GFP_KERNEL);
+ if (!rq->cmd)
+ goto out_put_request;
}
+ ret = -EFAULT;
+ if (blk_fill_sghdr_rq(q, rq, hdr, mode))
+ goto out_free_cdb;
+
+ ret = 0;
if (hdr->iovec_count) {
size_t iov_data_len;
struct iovec *iov = NULL;
0, NULL, &iov);
if (ret < 0) {
kfree(iov);
- goto out;
+ goto out_free_cdb;
}
iov_data_len = ret;
GFP_KERNEL);
if (ret)
- goto out;
+ goto out_free_cdb;
bio = rq->bio;
memset(sense, 0, sizeof(sense));
hdr->duration = jiffies_to_msecs(jiffies - start_time);
- return blk_complete_sghdr_rq(rq, hdr, bio);
-out:
+ ret = blk_complete_sghdr_rq(rq, hdr, bio);
+
+out_free_cdb:
+ if (rq->cmd != rq->__cmd)
+ kfree(rq->cmd);
+out_put_request:
blk_put_request(rq);
+out:
return ret;
}
}
rq = blk_get_request(q, in_len ? WRITE : READ, __GFP_WAIT);
+ if (!rq) {
+ err = -ENOMEM;
+ goto error;
+ }
+ blk_rq_set_block_pc(rq);
cmdlen = COMMAND_SIZE(opcode);
memset(sense, 0, sizeof(sense));
rq->sense = sense;
rq->sense_len = 0;
- blk_rq_set_block_pc(rq);
blk_execute_rq(q, disk, rq, 0);
error:
kfree(buffer);
- blk_put_request(rq);
+ if (rq)
+ blk_put_request(rq);
return err;
}
EXPORT_SYMBOL_GPL(sg_scsi_ioctl);
struct asymmetric_key_subtype public_key_subtype = {
.owner = THIS_MODULE,
.name = "public_key",
+ .name_len = sizeof("public_key") - 1,
.describe = public_key_describe,
.destroy = public_key_destroy,
.verify_signature = public_key_verify_signature_2,
{
struct win_certificate wrapper;
const u8 *pkcs7;
+ unsigned len;
if (ctx->sig_len < sizeof(wrapper)) {
pr_debug("Signature wrapper too short\n");
return -ENOTSUPP;
}
- /* Looks like actual pkcs signature length is in wrapper->length.
- * size obtained from data dir entries lists the total size of
- * certificate table which is also aligned to octawrod boundary.
- *
- * So set signature length field appropriately.
+ /* It looks like the pkcs signature length in wrapper->length and the
+ * size obtained from the data dir entries, which lists the total size
+ * of certificate table, are both aligned to an octaword boundary, so
+ * we may have to deal with some padding.
*/
ctx->sig_len = wrapper.length;
ctx->sig_offset += sizeof(wrapper);
ctx->sig_len -= sizeof(wrapper);
- if (ctx->sig_len == 0) {
+ if (ctx->sig_len < 4) {
pr_debug("Signature data missing\n");
return -EKEYREJECTED;
}
- /* What's left should a PKCS#7 cert */
+ /* What's left should be a PKCS#7 cert */
pkcs7 = pebuf + ctx->sig_offset;
- if (pkcs7[0] == (ASN1_CONS_BIT | ASN1_SEQ)) {
- if (pkcs7[1] == 0x82 &&
- pkcs7[2] == (((ctx->sig_len - 4) >> 8) & 0xff) &&
- pkcs7[3] == ((ctx->sig_len - 4) & 0xff))
- return 0;
- if (pkcs7[1] == 0x80)
- return 0;
- if (pkcs7[1] > 0x82)
- return -EMSGSIZE;
+ if (pkcs7[0] != (ASN1_CONS_BIT | ASN1_SEQ))
+ goto not_pkcs7;
+
+ switch (pkcs7[1]) {
+ case 0 ... 0x7f:
+ len = pkcs7[1] + 2;
+ goto check_len;
+ case ASN1_INDEFINITE_LENGTH:
+ return 0;
+ case 0x81:
+ len = pkcs7[2] + 3;
+ goto check_len;
+ case 0x82:
+ len = ((pkcs7[2] << 8) | pkcs7[3]) + 4;
+ goto check_len;
+ case 0x83 ... 0xff:
+ return -EMSGSIZE;
+ default:
+ goto not_pkcs7;
}
+check_len:
+ if (len <= ctx->sig_len) {
+ /* There may be padding */
+ ctx->sig_len = len;
+ return 0;
+ }
+not_pkcs7:
pr_debug("Signature data not PKCS#7\n");
return -ELIBBAD;
}
.setup = lpss_i2c_setup,
};
+static struct lpss_shared_clock bsw_pwm_clock = {
+ .name = "pwm_clk",
+ .rate = 19200000,
+};
+
+static struct lpss_device_desc bsw_pwm_dev_desc = {
+ .clk_required = true,
+ .save_ctx = true,
+ .shared_clock = &bsw_pwm_clock,
+};
+
#else
#define LPSS_ADDR(desc) (0UL)
{ "INT33B2", },
{ "INT33FC", },
+ /* Braswell LPSS devices */
+ { "80862288", LPSS_ADDR(bsw_pwm_dev_desc) },
+ { "8086228A", LPSS_ADDR(byt_uart_dev_desc) },
+ { "8086228E", LPSS_ADDR(byt_spi_dev_desc) },
+ { "808622C1", LPSS_ADDR(byt_i2c_dev_desc) },
+
{ "INT3430", LPSS_ADDR(lpt_dev_desc) },
{ "INT3431", LPSS_ADDR(lpt_dev_desc) },
{ "INT3432", LPSS_ADDR(lpt_i2c_dev_desc) },
t->rdata[t->ri++] = acpi_ec_read_data(ec);
if (t->rlen == t->ri) {
t->flags |= ACPI_EC_COMMAND_COMPLETE;
+ if (t->command == ACPI_EC_COMMAND_QUERY)
+ pr_debug("hardware QR_EC completion\n");
wakeup = true;
}
} else
}
return wakeup;
} else {
- if ((status & ACPI_EC_FLAG_IBF) == 0) {
+ /*
+ * There is firmware refusing to respond QR_EC when SCI_EVT
+ * is not set, for which case, we complete the QR_EC
+ * without issuing it to the firmware.
+ * https://bugzilla.kernel.org/show_bug.cgi?id=86211
+ */
+ if (!(status & ACPI_EC_FLAG_SCI) &&
+ (t->command == ACPI_EC_COMMAND_QUERY)) {
+ t->flags |= ACPI_EC_COMMAND_POLL;
+ t->rdata[t->ri++] = 0x00;
+ t->flags |= ACPI_EC_COMMAND_COMPLETE;
+ pr_debug("software QR_EC completion\n");
+ wakeup = true;
+ } else if ((status & ACPI_EC_FLAG_IBF) == 0) {
acpi_ec_write_cmd(ec, t->command);
t->flags |= ACPI_EC_COMMAND_POLL;
} else
/* following two actions should be kept atomic */
ec->curr = t;
start_transaction(ec);
- if (ec->curr->command == ACPI_EC_COMMAND_QUERY)
- clear_bit(EC_FLAGS_QUERY_PENDING, &ec->flags);
spin_unlock_irqrestore(&ec->lock, tmp);
ret = ec_poll(ec);
spin_lock_irqsave(&ec->lock, tmp);
+ if (ec->curr->command == ACPI_EC_COMMAND_QUERY)
+ clear_bit(EC_FLAGS_QUERY_PENDING, &ec->flags);
ec->curr = NULL;
spin_unlock_irqrestore(&ec->lock, tmp);
return ret;
/* Keep IOAPIC pin configuration when suspending */
if (dev->dev.power.is_prepared)
return;
+#ifdef CONFIG_PM_RUNTIME
+ if (dev->dev.power.runtime_status == RPM_SUSPENDING)
+ return;
+#endif
entry = acpi_pci_irq_lookup(dev, pin);
if (!entry)
device->driver->ops.notify(device, event);
}
-static acpi_status acpi_device_notify_fixed(void *data)
+static void acpi_device_notify_fixed(void *data)
{
struct acpi_device *device = data;
/* Fixed hardware devices have no handles */
acpi_device_notify(NULL, ACPI_FIXED_HARDWARE_EVENT, device);
+}
+
+static acpi_status acpi_device_fixed_event(void *data)
+{
+ acpi_os_execute(OSL_NOTIFY_HANDLER, acpi_device_notify_fixed, data);
return AE_OK;
}
if (device->device_type == ACPI_BUS_TYPE_POWER_BUTTON)
status =
acpi_install_fixed_event_handler(ACPI_EVENT_POWER_BUTTON,
- acpi_device_notify_fixed,
+ acpi_device_fixed_event,
device);
else if (device->device_type == ACPI_BUS_TYPE_SLEEP_BUTTON)
status =
acpi_install_fixed_event_handler(ACPI_EVENT_SLEEP_BUTTON,
- acpi_device_notify_fixed,
+ acpi_device_fixed_event,
device);
else
status = acpi_install_notify_handler(device->handle,
{
if (device->device_type == ACPI_BUS_TYPE_POWER_BUTTON)
acpi_remove_fixed_event_handler(ACPI_EVENT_POWER_BUTTON,
- acpi_device_notify_fixed);
+ acpi_device_fixed_event);
else if (device->device_type == ACPI_BUS_TYPE_SLEEP_BUTTON)
acpi_remove_fixed_event_handler(ACPI_EVENT_SLEEP_BUTTON,
- acpi_device_notify_fixed);
+ acpi_device_fixed_event);
else
acpi_remove_notify_handler(device->handle, ACPI_DEVICE_NOTIFY,
acpi_device_notify);
struct acpi_driver *acpi_drv = to_acpi_driver(dev->driver);
int ret;
- if (acpi_dev->handler)
+ if (acpi_dev->handler && !acpi_is_pnp_device(acpi_dev))
return -EINVAL;
if (!acpi_drv->ops.add)
enum regcache_type type;
int (*init)(struct regmap *map);
int (*exit)(struct regmap *map);
+#ifdef CONFIG_DEBUG_FS
+ void (*debugfs_init)(struct regmap *map);
+#endif
int (*read)(struct regmap *map, unsigned int reg, unsigned int *value);
int (*write)(struct regmap *map, unsigned int reg, unsigned int value);
int (*sync)(struct regmap *map, unsigned int min, unsigned int max);
{
debugfs_create_file("rbtree", 0400, map->debugfs, map, &rbtree_fops);
}
-#else
-static void rbtree_debugfs_init(struct regmap *map)
-{
-}
#endif
static int regcache_rbtree_init(struct regmap *map)
goto err;
}
- rbtree_debugfs_init(map);
-
return 0;
err:
.name = "rbtree",
.init = regcache_rbtree_init,
.exit = regcache_rbtree_exit,
+#ifdef CONFIG_DEBUG_FS
+ .debugfs_init = rbtree_debugfs_init,
+#endif
.read = regcache_rbtree_read,
.write = regcache_rbtree_write,
.sync = regcache_rbtree_sync,
unsigned int block_base, unsigned int start,
unsigned int end)
{
- if (regmap_can_raw_write(map))
+ if (regmap_can_raw_write(map) && !map->use_single_rw)
return regcache_sync_block_raw(map, block, cache_present,
block_base, start, end);
else
next = rb_next(&range_node->node);
}
+
+ if (map->cache_ops && map->cache_ops->debugfs_init)
+ map->cache_ops->debugfs_init(map);
}
void regmap_debugfs_exit(struct regmap *map)
bool regmap_volatile(struct regmap *map, unsigned int reg)
{
- if (!regmap_readable(map, reg))
+ if (!map->format.format_write && !regmap_readable(map, reg))
return false;
if (map->volatile_reg)
int rd_size = CONFIG_BLK_DEV_RAM_SIZE;
static int max_part;
static int part_shift;
+static int part_show = 0;
module_param(rd_nr, int, S_IRUGO);
MODULE_PARM_DESC(rd_nr, "Maximum number of brd devices");
module_param(rd_size, int, S_IRUGO);
MODULE_PARM_DESC(rd_size, "Size of each RAM disk in kbytes.");
module_param(max_part, int, S_IRUGO);
MODULE_PARM_DESC(max_part, "Maximum number of partitions per RAM disk");
+module_param(part_show, int, S_IRUGO);
+MODULE_PARM_DESC(part_show, "Control RAM disk visibility in /proc/partitions");
MODULE_LICENSE("GPL");
MODULE_ALIAS_BLOCKDEV_MAJOR(RAMDISK_MAJOR);
MODULE_ALIAS("rd");
disk->fops = &brd_fops;
disk->private_data = brd;
disk->queue = brd->brd_queue;
- disk->flags |= GENHD_FL_SUPPRESS_PARTITION_INFO;
+ if (!part_show)
+ disk->flags |= GENHD_FL_SUPPRESS_PARTITION_INFO;
sprintf(disk->disk_name, "ram%d", i);
set_capacity(disk, rd_size * 2);
.probe = ace_probe,
.remove = ace_remove,
.driver = {
- .owner = THIS_MODULE,
.name = "xsysace",
.of_match_table = ace_of_match,
},
/* Should NEVER happen. Return bio error if it does. */
if (unlikely(ret)) {
pr_err("Decompression failed! err=%d, page=%u\n", ret, index);
- atomic64_inc(&zram->stats.failed_reads);
return ret;
}
zcomp_strm_release(zram->comp, zstrm);
if (is_partial_io(bvec))
kfree(uncmem);
- if (ret)
- atomic64_inc(&zram->stats.failed_writes);
return ret;
}
ret = zram_bvec_write(zram, bvec, index, offset);
}
+ if (unlikely(ret)) {
+ if (rw == READ)
+ atomic64_inc(&zram->stats.failed_reads);
+ else
+ atomic64_inc(&zram->stats.failed_writes);
+ }
+
return ret;
}
atomic64_t compr_data_size; /* compressed size of pages stored */
atomic64_t num_reads; /* failed + successful */
atomic64_t num_writes; /* --do-- */
- atomic64_t failed_reads; /* should NEVER! happen */
+ atomic64_t failed_reads; /* can happen when memory is too low */
atomic64_t failed_writes; /* can happen when memory is too low */
atomic64_t invalid_io; /* non-page-aligned I/O requests */
atomic64_t notify_free; /* no. of swap slot free notifications */
ICPU(0x3f, core_params),
ICPU(0x45, core_params),
ICPU(0x46, core_params),
+ ICPU(0x4c, byt_params),
ICPU(0x4f, core_params),
ICPU(0x56, core_params),
{}
add_timer_on(&cpu->timer, cpunum);
- pr_info("Intel pstate controlling: cpu %d\n", cpunum);
+ pr_debug("Intel pstate controlling: cpu %d\n", cpunum);
return 0;
}
return val >> 8;
}
-static int __init s5pv210_cpu_init(struct cpufreq_policy *policy)
+static int s5pv210_cpu_init(struct cpufreq_policy *policy)
{
unsigned long mem_type;
int ret;
return idx;
}
-static int __init bl_idle_driver_init(struct cpuidle_driver *drv, int cpu_id)
+static int __init bl_idle_driver_init(struct cpuidle_driver *drv, int part_id)
{
- struct cpuinfo_arm *cpu_info;
struct cpumask *cpumask;
- unsigned long cpuid;
int cpu;
cpumask = kzalloc(cpumask_size(), GFP_KERNEL);
if (!cpumask)
return -ENOMEM;
- for_each_possible_cpu(cpu) {
- cpu_info = &per_cpu(cpu_data, cpu);
- cpuid = is_smp() ? cpu_info->cpuid : read_cpuid_id();
-
- /* read cpu id part number */
- if ((cpuid & 0xFFF0) == cpu_id)
+ for_each_possible_cpu(cpu)
+ if (smp_cpuid_part(cpu) == part_id)
cpumask_set_cpu(cpu, cpumask);
- }
drv->cpumask = cpumask;
EXPORT_TRACEPOINT_SYMBOL(fence_annotate_wait_on);
EXPORT_TRACEPOINT_SYMBOL(fence_emit);
-/**
+/*
* fence context counter: each execution context should have its own
* fence context, this allows checking if fences belong to the same
* context or not. One device can have multiple separate contexts,
{0x25, 0x65, 0x80}, /* 16: VCLK88.75 */
{0x77, 0x58, 0x80}, /* 17: VCLK119 */
{0x32, 0x67, 0x80}, /* 18: VCLK85_5 */
+ {0x6a, 0x6d, 0x80}, /* 19: VCLK97_75 */
};
static struct ast_vbios_stdtable vbios_stdtable[] = {
return -EINVAL;
/* overflow checks for 32bit size calculations */
+ /* NOTE: DIV_ROUND_UP() can overflow */
cpp = DIV_ROUND_UP(args->bpp, 8);
- if (cpp > 0xffffffffU / args->width)
+ if (!cpp || cpp > 0xffffffffU / args->width)
return -EINVAL;
stride = cpp * args->width;
if (args->height > 0xffffffffU / stride)
}
}
-static int __init intel_no_opregion_vbt_callback(const struct dmi_system_id *id)
+static int intel_no_opregion_vbt_callback(const struct dmi_system_id *id)
{
DRM_DEBUG_KMS("Falling back to manually reading VBT from "
"VBIOS ROM for %s\n",
.destroy = intel_encoder_destroy,
};
-static int __init intel_no_crt_dmi_callback(const struct dmi_system_id *id)
+static int intel_no_crt_dmi_callback(const struct dmi_system_id *id)
{
DRM_INFO("Skipping CRT initialization for %s\n", id->ident);
return 1;
if (need_vtd_wa(dev) && alignment < 256 * 1024)
alignment = 256 * 1024;
+ /*
+ * Global gtt pte registers are special registers which actually forward
+ * writes to a chunk of system memory. Which means that there is no risk
+ * that the register values disappear as soon as we call
+ * intel_runtime_pm_put(), so it is correct to wrap only the
+ * pin/unpin/fence and not more.
+ */
+ intel_runtime_pm_get(dev_priv);
+
dev_priv->mm.interruptible = false;
ret = i915_gem_object_pin_to_display_plane(obj, alignment, pipelined);
if (ret)
i915_gem_object_pin_fence(obj);
dev_priv->mm.interruptible = true;
+ intel_runtime_pm_put(dev_priv);
return 0;
err_unpin:
i915_gem_object_unpin_from_display_plane(obj);
err_interruptible:
dev_priv->mm.interruptible = true;
+ intel_runtime_pm_put(dev_priv);
return ret;
}
intel_set_pch_fifo_underrun_reporting(dev, pipe, false);
intel_disable_pipe(dev_priv, pipe);
-
- if (intel_crtc->config.dp_encoder_is_mst)
- intel_ddi_set_vc_payload_alloc(crtc, false);
-
ironlake_pfit_disable(intel_crtc);
for_each_encoder_on_crtc(dev, crtc, encoder)
intel_set_pch_fifo_underrun_reporting(dev, TRANSCODER_A, false);
intel_disable_pipe(dev_priv, pipe);
+ if (intel_crtc->config.dp_encoder_is_mst)
+ intel_ddi_set_vc_payload_alloc(crtc, false);
+
intel_ddi_disable_transcoder_func(dev_priv, cpu_transcoder);
ironlake_pfit_disable(intel_crtc);
goto fail_locked;
}
+ /*
+ * Global gtt pte registers are special registers which actually
+ * forward writes to a chunk of system memory. Which means that
+ * there is no risk that the register values disappear as soon
+ * as we call intel_runtime_pm_put(), so it is correct to wrap
+ * only the pin/unpin/fence and not more.
+ */
+ intel_runtime_pm_get(dev_priv);
+
/* Note that the w/a also requires 2 PTE of padding following
* the bo. We currently fill all unused PTE with the shadow
* page and so we should always have valid PTE following the
ret = i915_gem_object_pin_to_display_plane(obj, alignment, NULL);
if (ret) {
DRM_DEBUG_KMS("failed to move cursor bo into the GTT\n");
+ intel_runtime_pm_put(dev_priv);
goto fail_locked;
}
ret = i915_gem_object_put_fence(obj);
if (ret) {
DRM_DEBUG_KMS("failed to release fence for cursor");
+ intel_runtime_pm_put(dev_priv);
goto fail_unpin;
}
addr = i915_gem_obj_ggtt_offset(obj);
+
+ intel_runtime_pm_put(dev_priv);
} else {
int align = IS_I830(dev) ? 16 * 1024 : 256;
ret = i915_gem_object_attach_phys(obj, align);
/* Acer C720 and C720P Chromebooks (Celeron 2955U) have backlights */
{ 0x0a06, 0x1025, 0x0a11, quirk_backlight_present },
+ /* Acer C720 Chromebook (Core i3 4005U) */
+ { 0x0a16, 0x1025, 0x0a11, quirk_backlight_present },
+
/* Toshiba CB35 Chromebook (Celeron 2955U) */
{ 0x0a06, 0x1179, 0x0a88, quirk_backlight_present },
return intel_dp_detect_dpcd(intel_dp);
}
-static enum drm_connector_status
-g4x_dp_detect(struct intel_dp *intel_dp)
+static int g4x_digital_port_connected(struct drm_device *dev,
+ struct intel_digital_port *intel_dig_port)
{
- struct drm_device *dev = intel_dp_to_dev(intel_dp);
struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
uint32_t bit;
- /* Can't disconnect eDP, but you can close the lid... */
- if (is_edp(intel_dp)) {
- enum drm_connector_status status;
-
- status = intel_panel_detect(dev);
- if (status == connector_status_unknown)
- status = connector_status_connected;
- return status;
- }
-
if (IS_VALLEYVIEW(dev)) {
switch (intel_dig_port->port) {
case PORT_B:
bit = PORTD_HOTPLUG_LIVE_STATUS_VLV;
break;
default:
- return connector_status_unknown;
+ return -EINVAL;
}
} else {
switch (intel_dig_port->port) {
bit = PORTD_HOTPLUG_LIVE_STATUS_G4X;
break;
default:
- return connector_status_unknown;
+ return -EINVAL;
}
}
if ((I915_READ(PORT_HOTPLUG_STAT) & bit) == 0)
+ return 0;
+ return 1;
+}
+
+static enum drm_connector_status
+g4x_dp_detect(struct intel_dp *intel_dp)
+{
+ struct drm_device *dev = intel_dp_to_dev(intel_dp);
+ struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
+ int ret;
+
+ /* Can't disconnect eDP, but you can close the lid... */
+ if (is_edp(intel_dp)) {
+ enum drm_connector_status status;
+
+ status = intel_panel_detect(dev);
+ if (status == connector_status_unknown)
+ status = connector_status_connected;
+ return status;
+ }
+
+ ret = g4x_digital_port_connected(dev, intel_dig_port);
+ if (ret == -EINVAL)
+ return connector_status_unknown;
+ else if (ret == 0)
return connector_status_disconnected;
return intel_dp_detect_dpcd(intel_dp);
intel_display_power_get(dev_priv, power_domain);
if (long_hpd) {
- if (!ibx_digital_port_connected(dev_priv, intel_dig_port))
- goto mst_fail;
+
+ if (HAS_PCH_SPLIT(dev)) {
+ if (!ibx_digital_port_connected(dev_priv, intel_dig_port))
+ goto mst_fail;
+ } else {
+ if (g4x_digital_port_connected(dev, intel_dig_port) != 1)
+ goto mst_fail;
+ }
if (!intel_dp_get_dpcd(intel_dp)) {
goto mst_fail;
.destroy = intel_encoder_destroy,
};
-static int __init intel_no_lvds_dmi_callback(const struct dmi_system_id *id)
+static int intel_no_lvds_dmi_callback(const struct dmi_system_id *id)
{
DRM_INFO("Skipping LVDS initialization for %s\n", id->ident);
return 1;
cpu_ctl2 = I915_READ(BLC_PWM_CPU_CTL2);
if (cpu_ctl2 & BLM_PWM_ENABLE) {
- WARN(1, "cpu backlight already enabled\n");
+ DRM_DEBUG_KMS("cpu backlight already enabled\n");
cpu_ctl2 &= ~BLM_PWM_ENABLE;
I915_WRITE(BLC_PWM_CPU_CTL2, cpu_ctl2);
}
ctl = I915_READ(BLC_PWM_CTL);
if (ctl & BACKLIGHT_DUTY_CYCLE_MASK_PNV) {
- WARN(1, "backlight already enabled\n");
+ DRM_DEBUG_KMS("backlight already enabled\n");
I915_WRITE(BLC_PWM_CTL, 0);
}
ctl2 = I915_READ(BLC_PWM_CTL2);
if (ctl2 & BLM_PWM_ENABLE) {
- WARN(1, "backlight already enabled\n");
+ DRM_DEBUG_KMS("backlight already enabled\n");
ctl2 &= ~BLM_PWM_ENABLE;
I915_WRITE(BLC_PWM_CTL2, ctl2);
}
ctl2 = I915_READ(VLV_BLC_PWM_CTL2(pipe));
if (ctl2 & BLM_PWM_ENABLE) {
- WARN(1, "backlight already enabled\n");
+ DRM_DEBUG_KMS("backlight already enabled\n");
ctl2 &= ~BLM_PWM_ENABLE;
I915_WRITE(VLV_BLC_PWM_CTL2(pipe), ctl2);
}
{
struct drm_display_mode mode;
struct intel_tv *intel_tv = intel_attached_tv(connector);
+ enum drm_connector_status status;
int type;
DRM_DEBUG_KMS("[CONNECTOR:%d:%s] force=%d\n",
if (intel_get_load_detect_pipe(connector, &mode, &tmp, &ctx)) {
type = intel_tv_detect_type(intel_tv, connector);
intel_release_load_detect_pipe(connector, &tmp);
+ status = type < 0 ?
+ connector_status_disconnected :
+ connector_status_connected;
} else
- return connector_status_unknown;
+ status = connector_status_unknown;
drm_modeset_drop_locks(&ctx);
drm_modeset_acquire_fini(&ctx);
} else
return connector->status;
- if (type < 0)
- return connector_status_disconnected;
+ if (status != connector_status_connected)
+ return status;
intel_tv->type = type;
intel_tv_find_better_format(connector);
struct mdp4_crtc *mdp4_crtc = to_mdp4_crtc(crtc);
DBG("%s", mdp4_crtc->name);
/* make sure we hold a ref to mdp clks while setting up mode: */
+ drm_crtc_vblank_get(crtc);
mdp4_enable(get_kms(crtc));
mdp4_crtc_dpms(crtc, DRM_MODE_DPMS_OFF);
}
crtc_flush(crtc);
/* drop the ref to mdp clk's that we got in prepare: */
mdp4_disable(get_kms(crtc));
+ drm_crtc_vblank_put(crtc);
}
static int mdp4_crtc_mode_set_base(struct drm_crtc *crtc, int x, int y,
for (i = 0; i < ARRAY_SIZE(devnames); i++) {
struct device *dev;
- int ret;
dev = bus_find_device_by_name(&platform_bus_type,
NULL, devnames[i]);
if (!dev) {
- dev_info(master, "still waiting for %s\n", devnames[i]);
+ dev_info(&pdev->dev, "still waiting for %s\n", devnames[i]);
return -EPROBE_DEFER;
}
ret = msm_gem_get_iova_locked(fbdev->bo, 0, &paddr);
if (ret) {
dev_err(dev->dev, "failed to get buffer obj iova: %d\n", ret);
- goto fail;
+ goto fail_unlock;
}
fbi = framebuffer_alloc(0, dev->dev);
static int msm_fault_handler(struct iommu_domain *iommu, struct device *dev,
unsigned long iova, int flags, void *arg)
{
- DBG("*** fault: iova=%08lx, flags=%d", iova, flags);
- return -ENOSYS;
+ pr_warn_ratelimited("*** fault: iova=%08lx, flags=%d\n", iova, flags);
+ return 0;
}
static int msm_iommu_attach(struct msm_mmu *mmu, const char **names, int cnt)
sclass = nv_parent(parent)->sclass;
while (sclass) {
if (++nr < size)
- lclass[nr] = sclass->oclass->handle;
+ lclass[nr] = sclass->oclass->handle & 0xffff;
sclass = sclass->sclass;
}
if (engine && (oclass = engine->sclass)) {
while (oclass->ofuncs) {
if (++nr < size)
- lclass[nr] = oclass->handle;
+ lclass[nr] = oclass->handle & 0xffff;
oclass++;
}
}
WREG32(0x15D8, 0);
WREG32(0x15DC, 0);
- /* empty context1-15 */
- /* FIXME start with 4G, once using 2 level pt switch to full
- * vm size space
- */
+ /* restore context1-15 */
/* set vm size, must be a multiple of 4 */
WREG32(VM_CONTEXT1_PAGE_TABLE_START_ADDR, 0);
WREG32(VM_CONTEXT1_PAGE_TABLE_END_ADDR, rdev->vm_manager.max_pfn);
for (i = 1; i < 16; i++) {
if (i < 8)
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
else
WREG32(VM_CONTEXT8_PAGE_TABLE_BASE_ADDR + ((i - 8) << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
}
/* enable context1-15 */
*/
static void cik_pcie_gart_disable(struct radeon_device *rdev)
{
+ unsigned i;
+
+ for (i = 1; i < 16; ++i) {
+ uint32_t reg;
+ if (i < 8)
+ reg = VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2);
+ else
+ reg = VM_CONTEXT8_PAGE_TABLE_BASE_ADDR + ((i - 8) << 2);
+ rdev->vm_manager.saved_table_addr[i] = RREG32(reg);
+ }
+
/* Disable all tables */
WREG32(VM_CONTEXT0_CNTL, 0);
WREG32(VM_CONTEXT1_CNTL, 0);
int ret, i;
u16 tmp16;
+ if (pci_is_root_bus(rdev->pdev->bus))
+ return;
+
if (radeon_pcie_gen2 == 0)
return;
if (orig != data)
WREG32_PCIE_PORT(PCIE_LC_LINK_WIDTH_CNTL, data);
- if (!disable_clkreq) {
+ if (!disable_clkreq &&
+ !pci_is_root_bus(rdev->pdev->bus)) {
struct pci_dev *root = rdev->pdev->bus->self;
u32 lnkcap;
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR + (i << 2), 0);
WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR + (i << 2), rdev->vm_manager.max_pfn);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
}
/* enable context1-7 */
static void cayman_pcie_gart_disable(struct radeon_device *rdev)
{
+ unsigned i;
+
+ for (i = 1; i < 8; ++i) {
+ rdev->vm_manager.saved_table_addr[i] = RREG32(
+ VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2));
+ }
+
/* Disable all tables */
WREG32(VM_CONTEXT0_CNTL, 0);
WREG32(VM_CONTEXT1_CNTL, 0);
{
u32 tiling_config;
u32 ramcfg;
- u32 cc_rb_backend_disable;
u32 cc_gc_shader_pipe_config;
u32 tmp;
int i, j;
}
tiling_config |= BANK_SWAPS(1);
- cc_rb_backend_disable = RREG32(CC_RB_BACKEND_DISABLE) & 0x00ff0000;
- tmp = R6XX_MAX_BACKENDS -
- r600_count_pipe_bits((cc_rb_backend_disable >> 16) & R6XX_MAX_BACKENDS_MASK);
- if (tmp < rdev->config.r600.max_backends) {
- rdev->config.r600.max_backends = tmp;
- }
-
cc_gc_shader_pipe_config = RREG32(CC_GC_SHADER_PIPE_CONFIG) & 0x00ffff00;
- tmp = R6XX_MAX_PIPES -
- r600_count_pipe_bits((cc_gc_shader_pipe_config >> 8) & R6XX_MAX_PIPES_MASK);
- if (tmp < rdev->config.r600.max_pipes) {
- rdev->config.r600.max_pipes = tmp;
- }
- tmp = R6XX_MAX_SIMDS -
- r600_count_pipe_bits((cc_gc_shader_pipe_config >> 16) & R6XX_MAX_SIMDS_MASK);
- if (tmp < rdev->config.r600.max_simds) {
- rdev->config.r600.max_simds = tmp;
- }
tmp = rdev->config.r600.max_simds -
r600_count_pipe_bits((cc_gc_shader_pipe_config >> 16) & R6XX_MAX_SIMDS_MASK);
rdev->config.r600.active_simds = tmp;
disabled_rb_mask = (RREG32(CC_RB_BACKEND_DISABLE) >> 16) & R6XX_MAX_BACKENDS_MASK;
+ tmp = 0;
+ for (i = 0; i < rdev->config.r600.max_backends; i++)
+ tmp |= (1 << i);
+ /* if all the backends are disabled, fix it up here */
+ if ((disabled_rb_mask & tmp) == tmp) {
+ for (i = 0; i < rdev->config.r600.max_backends; i++)
+ disabled_rb_mask &= ~(1 << i);
+ }
tmp = (tiling_config & PIPE_TILING__MASK) >> PIPE_TILING__SHIFT;
tmp = r6xx_remap_render_backend(rdev, tmp, rdev->config.r600.max_backends,
R6XX_MAX_BACKENDS, disabled_rb_mask);
u64 vram_base_offset;
/* is vm enabled? */
bool enabled;
+ /* for hw to save the PD addr on suspend/resume */
+ uint32_t saved_table_addr[RADEON_NUM_VM];
};
/*
u32 hdp_host_path_cntl;
u32 sq_dyn_gpr_size_simd_ab_0;
u32 gb_tiling_config = 0;
- u32 cc_rb_backend_disable = 0;
u32 cc_gc_shader_pipe_config = 0;
u32 mc_arb_ramcfg;
u32 db_debug4, tmp;
WREG32(SPI_CONFIG_CNTL, 0);
}
- cc_rb_backend_disable = RREG32(CC_RB_BACKEND_DISABLE) & 0x00ff0000;
- tmp = R7XX_MAX_BACKENDS - r600_count_pipe_bits(cc_rb_backend_disable >> 16);
- if (tmp < rdev->config.rv770.max_backends) {
- rdev->config.rv770.max_backends = tmp;
- }
-
cc_gc_shader_pipe_config = RREG32(CC_GC_SHADER_PIPE_CONFIG) & 0xffffff00;
- tmp = R7XX_MAX_PIPES - r600_count_pipe_bits((cc_gc_shader_pipe_config >> 8) & R7XX_MAX_PIPES_MASK);
- if (tmp < rdev->config.rv770.max_pipes) {
- rdev->config.rv770.max_pipes = tmp;
- }
- tmp = R7XX_MAX_SIMDS - r600_count_pipe_bits((cc_gc_shader_pipe_config >> 16) & R7XX_MAX_SIMDS_MASK);
- if (tmp < rdev->config.rv770.max_simds) {
- rdev->config.rv770.max_simds = tmp;
- }
tmp = rdev->config.rv770.max_simds -
r600_count_pipe_bits((cc_gc_shader_pipe_config >> 16) & R7XX_MAX_SIMDS_MASK);
rdev->config.rv770.active_simds = tmp;
rdev->config.rv770.tiling_npipes = rdev->config.rv770.max_tile_pipes;
disabled_rb_mask = (RREG32(CC_RB_BACKEND_DISABLE) >> 16) & R7XX_MAX_BACKENDS_MASK;
+ tmp = 0;
+ for (i = 0; i < rdev->config.rv770.max_backends; i++)
+ tmp |= (1 << i);
+ /* if all the backends are disabled, fix it up here */
+ if ((disabled_rb_mask & tmp) == tmp) {
+ for (i = 0; i < rdev->config.rv770.max_backends; i++)
+ disabled_rb_mask &= ~(1 << i);
+ }
tmp = (gb_tiling_config & PIPE_TILING__MASK) >> PIPE_TILING__SHIFT;
tmp = r6xx_remap_render_backend(rdev, tmp, rdev->config.rv770.max_backends,
R7XX_MAX_BACKENDS, disabled_rb_mask);
for (i = 1; i < 16; i++) {
if (i < 8)
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
else
WREG32(VM_CONTEXT8_PAGE_TABLE_BASE_ADDR + ((i - 8) << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
}
/* enable context1-15 */
static void si_pcie_gart_disable(struct radeon_device *rdev)
{
+ unsigned i;
+
+ for (i = 1; i < 16; ++i) {
+ uint32_t reg;
+ if (i < 8)
+ reg = VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2);
+ else
+ reg = VM_CONTEXT8_PAGE_TABLE_BASE_ADDR + ((i - 8) << 2);
+ rdev->vm_manager.saved_table_addr[i] = RREG32(reg);
+ }
+
/* Disable all tables */
WREG32(VM_CONTEXT0_CNTL, 0);
WREG32(VM_CONTEXT1_CNTL, 0);
int ret, i;
u16 tmp16;
+ if (pci_is_root_bus(rdev->pdev->bus))
+ return;
+
if (radeon_pcie_gen2 == 0)
return;
if (orig != data)
WREG32_PIF_PHY1(PB1_PIF_CNTL, data);
- if (!disable_clkreq) {
+ if (!disable_clkreq &&
+ !pci_is_root_bus(rdev->pdev->bus)) {
struct pci_dev *root = rdev->pdev->bus->self;
u32 lnkcap;
config DRM_STI
tristate "DRM Support for STMicroelectronics SoC stiH41x Series"
depends on DRM && (SOC_STIH415 || SOC_STIH416 || ARCH_MULTIPLATFORM)
+ select RESET_CONTROLLER
select DRM_KMS_HELPER
select DRM_GEM_CMA_HELPER
select DRM_KMS_CMA_HELPER
master = platform_device_register_resndata(dev,
DRIVER_NAME "__master", -1,
NULL, 0, NULL, 0);
- if (!master)
- return -EINVAL;
+ if (IS_ERR(master))
+ return PTR_ERR(master);
platform_set_drvdata(pdev, master);
return 0;
return -ENOMEM;
}
hda->regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
- if (IS_ERR(hda->regs))
- return PTR_ERR(hda->regs);
+ if (!hda->regs)
+ return -ENOMEM;
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"video-dacs-ctrl");
if (res) {
hda->video_dacs_ctrl = devm_ioremap_nocache(dev, res->start,
resource_size(res));
- if (IS_ERR(hda->video_dacs_ctrl))
- return PTR_ERR(hda->video_dacs_ctrl);
+ if (!hda->video_dacs_ctrl)
+ return -ENOMEM;
} else {
/* If no existing video-dacs-ctrl resource continue the probe */
DRM_DEBUG_DRIVER("No video-dacs-ctrl resource\n");
return 0;
}
-static struct of_device_id hda_of_match[] = {
+static const struct of_device_id hda_of_match[] = {
{ .compatible = "st,stih416-hda", },
{ .compatible = "st,stih407-hda", },
{ /* end node */ }
.unbind = sti_hdmi_unbind,
};
-static struct of_device_id hdmi_of_match[] = {
+static const struct of_device_id hdmi_of_match[] = {
{
.compatible = "st,stih416-hdmi",
.data = &tx3g0c55phy_ops,
return -ENOMEM;
}
hdmi->regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
- if (IS_ERR(hdmi->regs))
- return PTR_ERR(hdmi->regs);
+ if (!hdmi->regs)
+ return -ENOMEM;
if (of_device_is_compatible(np, "st,stih416-hdmi")) {
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
}
hdmi->syscfg = devm_ioremap_nocache(dev, res->start,
resource_size(res));
- if (IS_ERR(hdmi->syscfg))
- return PTR_ERR(hdmi->syscfg);
+ if (!hdmi->syscfg)
+ return -ENOMEM;
}
return -ENOMEM;
}
tvout->regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
- if (IS_ERR(tvout->regs))
- return PTR_ERR(tvout->regs);
+ if (!tvout->regs)
+ return -ENOMEM;
/* get reset resources */
tvout->reset = devm_reset_control_get(dev, "tvout");
return 0;
}
-static struct of_device_id tvout_of_match[] = {
+static const struct of_device_id tvout_of_match[] = {
{ .compatible = "st,stih416-tvout", },
{ .compatible = "st,stih407-tvout", },
{ /* end node */ }
res,
id_loc - sw_context->buf_start);
if (unlikely(ret != 0))
- goto out_err;
+ return ret;
ret = vmw_resource_val_add(sw_context, res, &node);
if (unlikely(ret != 0))
- goto out_err;
+ return ret;
if (res_type == vmw_res_context && dev_priv->has_mob &&
node->first_usage) {
ret = vmw_resource_context_res_add(dev_priv, sw_context, res);
if (unlikely(ret != 0))
- goto out_err;
+ return ret;
node->staged_bindings =
kzalloc(sizeof(*node->staged_bindings), GFP_KERNEL);
if (node->staged_bindings == NULL) {
DRM_ERROR("Failed to allocate context binding "
"information.\n");
- goto out_err;
+ return -ENOMEM;
}
INIT_LIST_HEAD(&node->staged_bindings->list);
}
if (p_val)
*p_val = node;
-out_err:
- return ret;
+ return 0;
}
mutex_lock(&dev_priv->hw_mutex);
+ vmw_write(dev_priv, SVGA_REG_SYNC, SVGA_SYNC_GENERIC);
while (vmw_read(dev_priv, SVGA_REG_BUSY) != 0)
- vmw_write(dev_priv, SVGA_REG_SYNC, SVGA_SYNC_GENERIC);
+ ;
dev_priv->last_read_seqno = ioread32(fifo_mem + SVGA_FIFO_FENCE);
struct dj_receiver_dev *djrcv_dev = hid_get_drvdata(hdev);
struct dj_report *dj_report = (struct dj_report *) data;
unsigned long flags;
- bool report_processed = false;
dbg_hid("%s, size:%d\n", __func__, size);
* device (via hid_input_report() ) and return 1 so hid-core does not do
* anything else with it.
*/
+
+ /* case 1) */
+ if (data[0] != REPORT_ID_DJ_SHORT)
+ return false;
+
if ((dj_report->device_index < DJ_DEVICE_INDEX_MIN) ||
(dj_report->device_index > DJ_DEVICE_INDEX_MAX)) {
- dev_err(&hdev->dev, "%s: invalid device index:%d\n",
+ /*
+ * Device index is wrong, bail out.
+ * This driver can ignore safely the receiver notifications,
+ * so ignore those reports too.
+ */
+ if (dj_report->device_index != DJ_RECEIVER_INDEX)
+ dev_err(&hdev->dev, "%s: invalid device index:%d\n",
__func__, dj_report->device_index);
return false;
}
spin_lock_irqsave(&djrcv_dev->lock, flags);
- if (dj_report->report_id == REPORT_ID_DJ_SHORT) {
- switch (dj_report->report_type) {
- case REPORT_TYPE_NOTIF_DEVICE_PAIRED:
- case REPORT_TYPE_NOTIF_DEVICE_UNPAIRED:
- logi_dj_recv_queue_notification(djrcv_dev, dj_report);
- break;
- case REPORT_TYPE_NOTIF_CONNECTION_STATUS:
- if (dj_report->report_params[CONNECTION_STATUS_PARAM_STATUS] ==
- STATUS_LINKLOSS) {
- logi_dj_recv_forward_null_report(djrcv_dev, dj_report);
- }
- break;
- default:
- logi_dj_recv_forward_report(djrcv_dev, dj_report);
+ switch (dj_report->report_type) {
+ case REPORT_TYPE_NOTIF_DEVICE_PAIRED:
+ case REPORT_TYPE_NOTIF_DEVICE_UNPAIRED:
+ logi_dj_recv_queue_notification(djrcv_dev, dj_report);
+ break;
+ case REPORT_TYPE_NOTIF_CONNECTION_STATUS:
+ if (dj_report->report_params[CONNECTION_STATUS_PARAM_STATUS] ==
+ STATUS_LINKLOSS) {
+ logi_dj_recv_forward_null_report(djrcv_dev, dj_report);
}
- report_processed = true;
+ break;
+ default:
+ logi_dj_recv_forward_report(djrcv_dev, dj_report);
}
spin_unlock_irqrestore(&djrcv_dev->lock, flags);
- return report_processed;
+ return true;
}
static int logi_dj_probe(struct hid_device *hdev,
#define DJ_MAX_PAIRED_DEVICES 6
#define DJ_MAX_NUMBER_NOTIFICATIONS 8
+#define DJ_RECEIVER_INDEX 0
#define DJ_DEVICE_INDEX_MIN 1
#define DJ_DEVICE_INDEX_MAX 6
if (size < 4 || ((size - 4) % 9) != 0)
return 0;
npoints = (size - 4) / 9;
+ if (npoints > 15) {
+ hid_warn(hdev, "invalid size value (%d) for TRACKPAD_REPORT_ID\n",
+ size);
+ return 0;
+ }
msc->ntouches = 0;
for (ii = 0; ii < npoints; ii++)
magicmouse_emit_touch(msc, ii, data + ii * 9 + 4);
if (size < 6 || ((size - 6) % 8) != 0)
return 0;
npoints = (size - 6) / 8;
+ if (npoints > 15) {
+ hid_warn(hdev, "invalid size value (%d) for MOUSE_REPORT_ID\n",
+ size);
+ return 0;
+ }
msc->ntouches = 0;
for (ii = 0; ii < npoints; ii++)
magicmouse_emit_touch(msc, ii, data + ii * 8 + 6);
if (!data)
return 1;
+ if (size > 64) {
+ hid_warn(hdev, "invalid size value (%d) for picolcd raw event\n",
+ size);
+ return 0;
+ }
+
if (report->id == REPORT_KEY_STATE) {
if (data->input_keys)
ret = picolcd_raw_keypad(data, report, raw_data+1, size-1);
data->conf |= (resol << DS1621_REG_CONFIG_RESOL_SHIFT);
i2c_smbus_write_byte_data(client, DS1621_REG_CONF, data->conf);
data->update_interval = ds1721_convrates[resol];
+ data->zbits = 7 - resol;
mutex_unlock(&data->update_lock);
return count;
}
EXPORT_SYMBOL(input_mt_report_pointer_emulation);
+static void __input_mt_drop_unused(struct input_dev *dev, struct input_mt *mt)
+{
+ int i;
+
+ for (i = 0; i < mt->num_slots; i++) {
+ if (!input_mt_is_used(mt, &mt->slots[i])) {
+ input_mt_slot(dev, i);
+ input_event(dev, EV_ABS, ABS_MT_TRACKING_ID, -1);
+ }
+ }
+}
+
/**
* input_mt_drop_unused() - Inactivate slots not seen in this frame
* @dev: input device with allocated MT slots
void input_mt_drop_unused(struct input_dev *dev)
{
struct input_mt *mt = dev->mt;
- int i;
- if (!mt)
- return;
-
- for (i = 0; i < mt->num_slots; i++) {
- if (!input_mt_is_used(mt, &mt->slots[i])) {
- input_mt_slot(dev, i);
- input_event(dev, EV_ABS, ABS_MT_TRACKING_ID, -1);
- }
+ if (mt) {
+ __input_mt_drop_unused(dev, mt);
+ mt->frame++;
}
-
- mt->frame++;
}
EXPORT_SYMBOL(input_mt_drop_unused);
return;
if (mt->flags & INPUT_MT_DROP_UNUSED)
- input_mt_drop_unused(dev);
+ __input_mt_drop_unused(dev, mt);
if ((mt->flags & INPUT_MT_POINTER) && !(mt->flags & INPUT_MT_SEMI_MT))
use_count = true;
input_mt_report_pointer_emulation(dev, use_count);
+
+ mt->frame++;
}
EXPORT_SYMBOL(input_mt_sync_frame);
return 0;
}
- psmouse_info(psmouse,
- "Unknown ALPS touchpad: E7=%3ph, EC=%3ph\n", e7, ec);
+ psmouse_dbg(psmouse,
+ "Likely not an ALPS touchpad: E7=%3ph, EC=%3ph\n", e7, ec);
return -EINVAL;
}
#include <linux/input/mt.h>
#include <linux/serio.h>
#include <linux/libps2.h>
+#include <asm/unaligned.h>
#include "psmouse.h"
#include "elantech.h"
input_sync(dev);
}
+static void elantech_report_trackpoint(struct psmouse *psmouse,
+ int packet_type)
+{
+ /*
+ * byte 0: 0 0 sx sy 0 M R L
+ * byte 1:~sx 0 0 0 0 0 0 0
+ * byte 2:~sy 0 0 0 0 0 0 0
+ * byte 3: 0 0 ~sy ~sx 0 1 1 0
+ * byte 4: x7 x6 x5 x4 x3 x2 x1 x0
+ * byte 5: y7 y6 y5 y4 y3 y2 y1 y0
+ *
+ * x and y are written in two's complement spread
+ * over 9 bits with sx/sy the relative top bit and
+ * x7..x0 and y7..y0 the lower bits.
+ * The sign of y is opposite to what the input driver
+ * expects for a relative movement
+ */
+
+ struct elantech_data *etd = psmouse->private;
+ struct input_dev *tp_dev = etd->tp_dev;
+ unsigned char *packet = psmouse->packet;
+ int x, y;
+ u32 t;
+
+ if (dev_WARN_ONCE(&psmouse->ps2dev.serio->dev,
+ !tp_dev,
+ psmouse_fmt("Unexpected trackpoint message\n"))) {
+ if (etd->debug == 1)
+ elantech_packet_dump(psmouse);
+ return;
+ }
+
+ t = get_unaligned_le32(&packet[0]);
+
+ switch (t & ~7U) {
+ case 0x06000030U:
+ case 0x16008020U:
+ case 0x26800010U:
+ case 0x36808000U:
+ x = packet[4] - (int)((packet[1]^0x80) << 1);
+ y = (int)((packet[2]^0x80) << 1) - packet[5];
+
+ input_report_key(tp_dev, BTN_LEFT, packet[0] & 0x01);
+ input_report_key(tp_dev, BTN_RIGHT, packet[0] & 0x02);
+ input_report_key(tp_dev, BTN_MIDDLE, packet[0] & 0x04);
+
+ input_report_rel(tp_dev, REL_X, x);
+ input_report_rel(tp_dev, REL_Y, y);
+
+ input_sync(tp_dev);
+
+ break;
+
+ default:
+ /* Dump unexpected packet sequences if debug=1 (default) */
+ if (etd->debug == 1)
+ elantech_packet_dump(psmouse);
+
+ break;
+ }
+}
+
/*
* Interpret complete data packets and report absolute mode input events for
* hardware version 3. (12 byte packets for two fingers)
if ((packet[0] & 0x0c) == 0x0c && (packet[3] & 0xce) == 0x0c)
return PACKET_V3_TAIL;
+ if ((packet[3] & 0x0f) == 0x06)
+ return PACKET_TRACKPOINT;
}
return PACKET_UNKNOWN;
case 3:
packet_type = elantech_packet_check_v3(psmouse);
- /* ignore debounce */
- if (packet_type == PACKET_DEBOUNCE)
- return PSMOUSE_FULL_PACKET;
-
- if (packet_type == PACKET_UNKNOWN)
+ switch (packet_type) {
+ case PACKET_UNKNOWN:
return PSMOUSE_BAD_DATA;
- elantech_report_absolute_v3(psmouse, packet_type);
+ case PACKET_DEBOUNCE:
+ /* ignore debounce */
+ break;
+
+ case PACKET_TRACKPOINT:
+ elantech_report_trackpoint(psmouse, packet_type);
+ break;
+
+ default:
+ elantech_report_absolute_v3(psmouse, packet_type);
+ break;
+ }
+
break;
case 4:
* Asus UX31 0x361f00 20, 15, 0e clickpad
* Asus UX32VD 0x361f02 00, 15, 0e clickpad
* Avatar AVIU-145A2 0x361f00 ? clickpad
+ * Fujitsu H730 0x570f00 c0, 14, 0c 3 hw buttons (**)
* Gigabyte U2442 0x450f01 58, 17, 0c 2 hw buttons
* Lenovo L430 0x350f02 b9, 15, 0c 2 hw buttons (*)
+ * Lenovo L530 0x350f02 b9, 15, 0c 2 hw buttons (*)
* Samsung NF210 0x150b00 78, 14, 0a 2 hw buttons
* Samsung NP770Z5E 0x575f01 10, 15, 0f clickpad
* Samsung NP700Z5B 0x361f06 21, 15, 0f clickpad
* Samsung RF710 0x450f00 ? 2 hw buttons
* System76 Pangolin 0x250f01 ? 2 hw buttons
* (*) + 3 trackpoint buttons
+ * (**) + 0 trackpoint buttons
+ * Note: Lenovo L430 and Lenovo L430 have the same fw_version/caps
*/
static void elantech_set_buttonpad_prop(struct psmouse *psmouse)
{
*/
static void elantech_disconnect(struct psmouse *psmouse)
{
+ struct elantech_data *etd = psmouse->private;
+
+ if (etd->tp_dev)
+ input_unregister_device(etd->tp_dev);
sysfs_remove_group(&psmouse->ps2dev.serio->dev.kobj,
&elantech_attr_group);
kfree(psmouse->private);
int elantech_init(struct psmouse *psmouse)
{
struct elantech_data *etd;
- int i, error;
+ int i;
+ int error = -EINVAL;
unsigned char param[3];
+ struct input_dev *tp_dev;
psmouse->private = etd = kzalloc(sizeof(struct elantech_data), GFP_KERNEL);
if (!etd)
goto init_fail;
}
+ /* The MSB indicates the presence of the trackpoint */
+ if ((etd->capabilities[0] & 0x80) == 0x80) {
+ tp_dev = input_allocate_device();
+
+ if (!tp_dev) {
+ error = -ENOMEM;
+ goto init_fail_tp_alloc;
+ }
+
+ etd->tp_dev = tp_dev;
+ snprintf(etd->tp_phys, sizeof(etd->tp_phys), "%s/input1",
+ psmouse->ps2dev.serio->phys);
+ tp_dev->phys = etd->tp_phys;
+ tp_dev->name = "Elantech PS/2 TrackPoint";
+ tp_dev->id.bustype = BUS_I8042;
+ tp_dev->id.vendor = 0x0002;
+ tp_dev->id.product = PSMOUSE_ELANTECH;
+ tp_dev->id.version = 0x0000;
+ tp_dev->dev.parent = &psmouse->ps2dev.serio->dev;
+ tp_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REL);
+ tp_dev->relbit[BIT_WORD(REL_X)] =
+ BIT_MASK(REL_X) | BIT_MASK(REL_Y);
+ tp_dev->keybit[BIT_WORD(BTN_LEFT)] =
+ BIT_MASK(BTN_LEFT) | BIT_MASK(BTN_MIDDLE) |
+ BIT_MASK(BTN_RIGHT);
+ error = input_register_device(etd->tp_dev);
+ if (error < 0)
+ goto init_fail_tp_reg;
+ }
+
psmouse->protocol_handler = elantech_process_byte;
psmouse->disconnect = elantech_disconnect;
psmouse->reconnect = elantech_reconnect;
psmouse->pktsize = etd->hw_version > 1 ? 6 : 4;
return 0;
-
+ init_fail_tp_reg:
+ input_free_device(tp_dev);
+ init_fail_tp_alloc:
+ sysfs_remove_group(&psmouse->ps2dev.serio->dev.kobj,
+ &elantech_attr_group);
init_fail:
+ psmouse_reset(psmouse);
kfree(etd);
- return -1;
+ return error;
}
#define PACKET_V4_HEAD 0x05
#define PACKET_V4_MOTION 0x06
#define PACKET_V4_STATUS 0x07
+#define PACKET_TRACKPOINT 0x08
/*
* track up to 5 fingers for v4 hardware
};
struct elantech_data {
+ struct input_dev *tp_dev; /* Relative device for trackpoint */
+ char tp_phys[32];
unsigned char reg_07;
unsigned char reg_10;
unsigned char reg_11;
#define I8042_MUX_PHYS_DESC "sparcps2/serio%d"
static void __iomem *kbd_iobase;
-static struct resource *kbd_res;
#define I8042_COMMAND_REG (kbd_iobase + 0x64UL)
#define I8042_DATA_REG (kbd_iobase + 0x60UL)
#ifdef CONFIG_PCI
+static struct resource *kbd_res;
+
#define OBP_PS2KBD_NAME1 "kb_ps2"
#define OBP_PS2KBD_NAME2 "keyboard"
#define OBP_PS2MS_NAME1 "kdmouse"
#include <linux/list.h>
#include <linux/spinlock.h>
#include <linux/device.h>
+#include <linux/timer.h>
#include <linux/err.h>
#include <linux/ctype.h>
#include <linux/leds.h>
-#include <linux/workqueue.h>
#include "leds.h"
static struct class *leds_class;
NULL,
};
-static void led_work_function(struct work_struct *ws)
+static void led_timer_function(unsigned long data)
{
- struct led_classdev *led_cdev =
- container_of(ws, struct led_classdev, blink_work.work);
+ struct led_classdev *led_cdev = (void *)data;
unsigned long brightness;
unsigned long delay;
}
}
- queue_delayed_work(system_wq, &led_cdev->blink_work,
- msecs_to_jiffies(delay));
+ mod_timer(&led_cdev->blink_timer, jiffies + msecs_to_jiffies(delay));
}
static void set_brightness_delayed(struct work_struct *ws)
INIT_WORK(&led_cdev->set_brightness_work, set_brightness_delayed);
- INIT_DELAYED_WORK(&led_cdev->blink_work, led_work_function);
+ init_timer(&led_cdev->blink_timer);
+ led_cdev->blink_timer.function = led_timer_function;
+ led_cdev->blink_timer.data = (unsigned long)led_cdev;
#ifdef CONFIG_LEDS_TRIGGERS
led_trigger_set_default(led_cdev);
#include <linux/module.h>
#include <linux/rwsem.h>
#include <linux/leds.h>
-#include <linux/workqueue.h>
#include "leds.h"
DECLARE_RWSEM(leds_list_lock);
return;
}
- queue_delayed_work(system_wq, &led_cdev->blink_work, 1);
+ mod_timer(&led_cdev->blink_timer, jiffies + 1);
}
unsigned long *delay_on,
unsigned long *delay_off)
{
- cancel_delayed_work_sync(&led_cdev->blink_work);
+ del_timer_sync(&led_cdev->blink_timer);
led_cdev->flags &= ~LED_BLINK_ONESHOT;
led_cdev->flags &= ~LED_BLINK_ONESHOT_STOP;
int invert)
{
if ((led_cdev->flags & LED_BLINK_ONESHOT) &&
- delayed_work_pending(&led_cdev->blink_work))
+ timer_pending(&led_cdev->blink_timer))
return;
led_cdev->flags |= LED_BLINK_ONESHOT;
void led_stop_software_blink(struct led_classdev *led_cdev)
{
- cancel_delayed_work_sync(&led_cdev->blink_work);
+ del_timer_sync(&led_cdev->blink_timer);
led_cdev->blink_delay_on = 0;
led_cdev->blink_delay_off = 0;
}
void led_set_brightness(struct led_classdev *led_cdev,
enum led_brightness brightness)
{
- /* delay brightness setting if need to stop soft-blink work */
+ /* delay brightness setting if need to stop soft-blink timer */
if (led_cdev->blink_delay_on || led_cdev->blink_delay_off) {
led_cdev->delayed_set_value = brightness;
schedule_work(&led_cdev->set_brightness_work);
unsigned int key_size, opt_params;
unsigned long long tmpll;
int ret;
+ size_t iv_size_padding;
struct dm_arg_set as;
const char *opt_string;
char dummy;
cc->dmreq_start = sizeof(struct ablkcipher_request);
cc->dmreq_start += crypto_ablkcipher_reqsize(any_tfm(cc));
- cc->dmreq_start = ALIGN(cc->dmreq_start, crypto_tfm_ctx_alignment());
- cc->dmreq_start += crypto_ablkcipher_alignmask(any_tfm(cc)) &
- ~(crypto_tfm_ctx_alignment() - 1);
+ cc->dmreq_start = ALIGN(cc->dmreq_start, __alignof__(struct dm_crypt_request));
+
+ if (crypto_ablkcipher_alignmask(any_tfm(cc)) < CRYPTO_MINALIGN) {
+ /* Allocate the padding exactly */
+ iv_size_padding = -(cc->dmreq_start + sizeof(struct dm_crypt_request))
+ & crypto_ablkcipher_alignmask(any_tfm(cc));
+ } else {
+ /*
+ * If the cipher requires greater alignment than kmalloc
+ * alignment, we don't know the exact position of the
+ * initialization vector. We must assume worst case.
+ */
+ iv_size_padding = crypto_ablkcipher_alignmask(any_tfm(cc));
+ }
cc->req_pool = mempool_create_kmalloc_pool(MIN_IOS, cc->dmreq_start +
- sizeof(struct dm_crypt_request) + cc->iv_size);
+ sizeof(struct dm_crypt_request) + iv_size_padding + cc->iv_size);
if (!cc->req_pool) {
ti->error = "Cannot allocate crypt request mempool";
goto bad;
}
cc->per_bio_data_size = ti->per_bio_data_size =
- sizeof(struct dm_crypt_io) + cc->dmreq_start +
- sizeof(struct dm_crypt_request) + cc->iv_size;
+ ALIGN(sizeof(struct dm_crypt_io) + cc->dmreq_start +
+ sizeof(struct dm_crypt_request) + iv_size_padding + cc->iv_size,
+ ARCH_KMALLOC_MINALIGN);
cc->page_pool = mempool_create_page_pool(MIN_POOL_PAGES, 0);
if (!cc->page_pool) {
if (ret)
return ret;
-#if CONFIG_DEBUG_FS
+#ifdef CONFIG_DEBUG_FS
/* Pass to debugfs */
ab8500_debug_resources[0].start = ab8500->irq;
ab8500_debug_resources[0].end = ab8500->irq;
}
i2c_set_clientdata(client, chip);
- snprintf(client->name, I2C_NAME_SIZE, "Chip_0x%d", client->addr);
+ snprintf(client->name, I2C_NAME_SIZE, "Chip_0x%x", client->addr);
chip->client = client;
/* Reset the chip */
default:
omap->nports = OMAP3_HS_USB_PORTS;
dev_dbg(dev,
- "USB HOST Rev:0x%d not recognized, assuming %d ports\n",
+ "USB HOST Rev:0x%x not recognized, assuming %d ports\n",
omap->usbhs_rev, omap->nports);
break;
}
* above.
*/
static struct twl4030_resconfig omap3_idle_rconfig[] = {
- TWL_REMAP_SLEEP(RES_VAUX1, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VAUX2, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VAUX3, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VAUX4, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VMMC1, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VMMC2, DEV_GRP_NULL, 0, 0),
+ TWL_REMAP_SLEEP(RES_VAUX1, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VAUX2, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VAUX3, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VAUX4, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VMMC1, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VMMC2, TWL4030_RESCONFIG_UNDEF, 0, 0),
TWL_REMAP_OFF(RES_VPLL1, DEV_GRP_P1, 3, 1),
TWL_REMAP_SLEEP(RES_VPLL2, DEV_GRP_P1, 0, 0),
- TWL_REMAP_SLEEP(RES_VSIM, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VDAC, DEV_GRP_NULL, 0, 0),
+ TWL_REMAP_SLEEP(RES_VSIM, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VDAC, TWL4030_RESCONFIG_UNDEF, 0, 0),
TWL_REMAP_SLEEP(RES_VINTANA1, TWL_DEV_GRP_P123, 1, 2),
TWL_REMAP_SLEEP(RES_VINTANA2, TWL_DEV_GRP_P123, 0, 2),
TWL_REMAP_SLEEP(RES_VINTDIG, TWL_DEV_GRP_P123, 1, 2),
TWL_REMAP_SLEEP(RES_VIO, TWL_DEV_GRP_P123, 2, 2),
TWL_REMAP_OFF(RES_VDD1, DEV_GRP_P1, 4, 1),
TWL_REMAP_OFF(RES_VDD2, DEV_GRP_P1, 3, 1),
- TWL_REMAP_SLEEP(RES_VUSB_1V5, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VUSB_1V8, DEV_GRP_NULL, 0, 0),
+ TWL_REMAP_SLEEP(RES_VUSB_1V5, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VUSB_1V8, TWL4030_RESCONFIG_UNDEF, 0, 0),
TWL_REMAP_SLEEP(RES_VUSB_3V1, TWL_DEV_GRP_P123, 0, 0),
/* Resource #20 USB charge pump skipped */
TWL_REMAP_SLEEP(RES_REGEN, TWL_DEV_GRP_P123, 2, 1),
cl->timer_count = MEI_CONNECT_TIMEOUT;
list_add_tail(&cb->list, &dev->ctrl_rd_list.list);
} else {
+ cl->state = MEI_FILE_INITIALIZING;
list_add_tail(&cb->list, &dev->ctrl_wr_list.list);
}
ndev = (struct mei_nfc_dev *) cldev->priv_data;
dev = ndev->cl->dev;
+ err = -ENOMEM;
mei_buf = kzalloc(length + MEI_NFC_HEADER_SIZE, GFP_KERNEL);
if (!mei_buf)
- return -ENOMEM;
+ goto out;
hdr = (struct mei_nfc_hci_hdr *) mei_buf;
hdr->cmd = MEI_NFC_CMD_HCI_SEND;
hdr->data_size = length;
memcpy(mei_buf + MEI_NFC_HEADER_SIZE, buf, length);
-
err = __mei_cl_send(ndev->cl, mei_buf, length + MEI_NFC_HEADER_SIZE);
if (err < 0)
- return err;
-
- kfree(mei_buf);
+ goto out;
if (!wait_event_interruptible_timeout(ndev->send_wq,
ndev->recv_req_id == ndev->req_id, HZ)) {
} else {
ndev->req_id++;
}
-
+out:
+ kfree(mei_buf);
return err;
}
u32 val;
val = readl(info->reg.gpmc_ecc_config);
- if (((val >> ECC_CONFIG_CS_SHIFT) & ~CS_MASK) != info->gpmc_cs)
+ if (((val >> ECC_CONFIG_CS_SHIFT) & CS_MASK) != info->gpmc_cs)
return -EINVAL;
/* read ecc result */
}
/* populate MTD interface based on ECC scheme */
- nand_chip->ecc.layout = &omap_oobinfo;
ecclayout = &omap_oobinfo;
switch (info->ecc_opt) {
+ case OMAP_ECC_HAM1_CODE_SW:
+ nand_chip->ecc.mode = NAND_ECC_SOFT;
+ break;
+
case OMAP_ECC_HAM1_CODE_HW:
pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n");
nand_chip->ecc.mode = NAND_ECC_HW;
nand_chip->ecc.priv = nand_bch_init(mtd,
nand_chip->ecc.size,
nand_chip->ecc.bytes,
- &nand_chip->ecc.layout);
+ &ecclayout);
if (!nand_chip->ecc.priv) {
pr_err("nand: error: unable to use s/w BCH library\n");
err = -EINVAL;
nand_chip->ecc.priv = nand_bch_init(mtd,
nand_chip->ecc.size,
nand_chip->ecc.bytes,
- &nand_chip->ecc.layout);
+ &ecclayout);
if (!nand_chip->ecc.priv) {
pr_err("nand: error: unable to use s/w BCH library\n");
err = -EINVAL;
goto return_error;
}
+ if (info->ecc_opt == OMAP_ECC_HAM1_CODE_SW)
+ goto scan_tail;
+
/* all OOB bytes from oobfree->offset till end off OOB are free */
ecclayout->oobfree->length = mtd->oobsize - ecclayout->oobfree->offset;
/* check if NAND device's OOB is enough to store ECC signatures */
err = -EINVAL;
goto return_error;
}
+ nand_chip->ecc.layout = ecclayout;
+scan_tail:
/* second phase scan */
if (nand_scan_tail(mtd)) {
err = -ENXIO;
controller, such as the one emulated by kvmtool.
config PCIE_SPEAR13XX
- tristate "STMicroelectronics SPEAr PCIe controller"
+ bool "STMicroelectronics SPEAr PCIe controller"
depends on ARCH_SPEAR13XX
select PCIEPORTBUS
select PCIE_DW
} else
seq_printf(s, " %-9s", chip->get(chip, offset) ? "hi" : "lo");
- if (pctldev)
- mode = abx500_get_mode(pctldev, chip, offset);
+ mode = abx500_get_mode(pctldev, chip, offset);
seq_printf(s, " %s", (mode < 0) ? "unknown" : modes[mode]);
static void at91_pin_dbg(const struct device *dev, const struct at91_pmx_pin *pin)
{
if (pin->mux) {
- dev_dbg(dev, "pio%c%d configured as periph%c with conf = 0x%lu\n",
+ dev_dbg(dev, "pio%c%d configured as periph%c with conf = 0x%lx\n",
pin->bank + 'A', pin->pin, pin->mux - 1 + 'A', pin->conf);
} else {
- dev_dbg(dev, "pio%c%d configured as gpio with conf = 0x%lu\n",
+ dev_dbg(dev, "pio%c%d configured as gpio with conf = 0x%lx\n",
pin->bank + 'A', pin->pin, pin->conf);
}
}
int reg, ret, mask;
unsigned long flags;
u8 bit;
- u32 data;
+ u32 data, rmask;
if (iomux_num > 3)
return -EINVAL;
spin_lock_irqsave(&bank->slock, flags);
data = (mask << (bit + 16));
+ rmask = data | (data >> 16);
data |= (mux & mask) << bit;
- ret = regmap_write(regmap, reg, data);
+ ret = regmap_update_bits(regmap, reg, rmask, data);
spin_unlock_irqrestore(&bank->slock, flags);
struct regmap *regmap;
unsigned long flags;
int reg, ret, i;
- u32 data;
+ u32 data, rmask;
u8 bit;
rk3288_calc_drv_reg_and_bit(bank, pin_num, ®map, ®, &bit);
/* enable the write to the equivalent lower bits */
data = ((1 << RK3288_DRV_BITS_PER_PIN) - 1) << (bit + 16);
+ rmask = data | (data >> 16);
data |= (ret << bit);
- ret = regmap_write(regmap, reg, data);
+ ret = regmap_update_bits(regmap, reg, rmask, data);
spin_unlock_irqrestore(&bank->slock, flags);
return ret;
int reg, ret;
unsigned long flags;
u8 bit;
- u32 data;
+ u32 data, rmask;
dev_dbg(info->dev, "setting pull of GPIO%d-%d to %d\n",
bank->bank_num, pin_num, pull);
/* enable the write to the equivalent lower bits */
data = ((1 << RK3188_PULL_BITS_PER_PIN) - 1) << (bit + 16);
+ rmask = data | (data >> 16);
switch (pull) {
case PIN_CONFIG_BIAS_DISABLE:
return -EINVAL;
}
- ret = regmap_write(regmap, reg, data);
+ ret = regmap_update_bits(regmap, reg, rmask, data);
spin_unlock_irqrestore(&bank->slock, flags);
break;
if (args->args_count <= 0)
return ERR_PTR(-EINVAL);
- if (index > ARRAY_SIZE(padctl->phys))
+ if (index >= ARRAY_SIZE(padctl->phys))
return ERR_PTR(-EINVAL);
return padctl->phys[index];
padctl->provider = devm_of_phy_provider_register(&pdev->dev,
tegra_xusb_padctl_xlate);
- if (err < 0) {
+ if (IS_ERR(padctl->provider)) {
+ err = PTR_ERR(padctl->provider);
dev_err(&pdev->dev, "failed to register PHYs: %d\n", err);
goto unregister;
}
struct irq_chip *chip = irq_data_get_irq_chip(irqd);
struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
- struct samsung_pin_bank_type *bank_type = bank->type;
struct samsung_pinctrl_drv_data *d = bank->drvdata;
- unsigned int pin = irqd->hwirq;
- unsigned int shift = EXYNOS_EINT_CON_LEN * pin;
+ unsigned int shift = EXYNOS_EINT_CON_LEN * irqd->hwirq;
unsigned int con, trig_type;
unsigned long reg_con = our_chip->eint_con + bank->eint_offset;
- unsigned long flags;
- unsigned int mask;
switch (type) {
case IRQ_TYPE_EDGE_RISING:
con |= trig_type << shift;
writel(con, d->virt_base + reg_con);
+ return 0;
+}
+
+static int exynos_irq_request_resources(struct irq_data *irqd)
+{
+ struct irq_chip *chip = irq_data_get_irq_chip(irqd);
+ struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
+ struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
+ struct samsung_pin_bank_type *bank_type = bank->type;
+ struct samsung_pinctrl_drv_data *d = bank->drvdata;
+ unsigned int shift = EXYNOS_EINT_CON_LEN * irqd->hwirq;
+ unsigned long reg_con = our_chip->eint_con + bank->eint_offset;
+ unsigned long flags;
+ unsigned int mask;
+ unsigned int con;
+ int ret;
+
+ ret = gpio_lock_as_irq(&bank->gpio_chip, irqd->hwirq);
+ if (ret) {
+ dev_err(bank->gpio_chip.dev, "unable to lock pin %s-%lu IRQ\n",
+ bank->name, irqd->hwirq);
+ return ret;
+ }
+
reg_con = bank->pctl_offset + bank_type->reg_offset[PINCFG_TYPE_FUNC];
- shift = pin * bank_type->fld_width[PINCFG_TYPE_FUNC];
+ shift = irqd->hwirq * bank_type->fld_width[PINCFG_TYPE_FUNC];
mask = (1 << bank_type->fld_width[PINCFG_TYPE_FUNC]) - 1;
spin_lock_irqsave(&bank->slock, flags);
spin_unlock_irqrestore(&bank->slock, flags);
+ exynos_irq_unmask(irqd);
+
return 0;
}
+static void exynos_irq_release_resources(struct irq_data *irqd)
+{
+ struct irq_chip *chip = irq_data_get_irq_chip(irqd);
+ struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
+ struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
+ struct samsung_pin_bank_type *bank_type = bank->type;
+ struct samsung_pinctrl_drv_data *d = bank->drvdata;
+ unsigned int shift = EXYNOS_EINT_CON_LEN * irqd->hwirq;
+ unsigned long reg_con = our_chip->eint_con + bank->eint_offset;
+ unsigned long flags;
+ unsigned int mask;
+ unsigned int con;
+
+ reg_con = bank->pctl_offset + bank_type->reg_offset[PINCFG_TYPE_FUNC];
+ shift = irqd->hwirq * bank_type->fld_width[PINCFG_TYPE_FUNC];
+ mask = (1 << bank_type->fld_width[PINCFG_TYPE_FUNC]) - 1;
+
+ exynos_irq_mask(irqd);
+
+ spin_lock_irqsave(&bank->slock, flags);
+
+ con = readl(d->virt_base + reg_con);
+ con &= ~(mask << shift);
+ con |= FUNC_INPUT << shift;
+ writel(con, d->virt_base + reg_con);
+
+ spin_unlock_irqrestore(&bank->slock, flags);
+
+ gpio_unlock_as_irq(&bank->gpio_chip, irqd->hwirq);
+}
+
/*
* irq_chip for gpio interrupts.
*/
.irq_mask = exynos_irq_mask,
.irq_ack = exynos_irq_ack,
.irq_set_type = exynos_irq_set_type,
+ .irq_request_resources = exynos_irq_request_resources,
+ .irq_release_resources = exynos_irq_release_resources,
},
.eint_con = EXYNOS_GPIO_ECON_OFFSET,
.eint_mask = EXYNOS_GPIO_EMASK_OFFSET,
.irq_ack = exynos_irq_ack,
.irq_set_type = exynos_irq_set_type,
.irq_set_wake = exynos_wkup_irq_set_wake,
+ .irq_request_resources = exynos_irq_request_resources,
+ .irq_release_resources = exynos_irq_release_resources,
},
.eint_con = EXYNOS_WKUP_ECON_OFFSET,
.eint_mask = EXYNOS_WKUP_EMASK_OFFSET,
#include <linux/gpio.h>
/* pinmux function number for pin as gpio output line */
+#define FUNC_INPUT 0x0
#define FUNC_OUTPUT 0x1
/**
};
static const char * const can0_groups[] = {
- "can0_data_a",
+ "can0_data",
"can0_data_b",
"can0_data_c",
"can0_data_d",
"can0_data_e",
"can0_data_f",
- "can_clk_a",
+ "can_clk",
"can_clk_b",
"can_clk_c",
"can_clk_d",
};
static const char * const can1_groups[] = {
- "can1_data_a",
+ "can1_data",
"can1_data_b",
"can1_data_c",
"can1_data_d",
- "can_clk_a",
+ "can_clk",
"can_clk_b",
"can_clk_c",
"can_clk_d",
struct dentry *debug;
unsigned long cfg;
bool has_hw_rfkill_switch;
- bool has_touchpad_control;
};
static bool no_bt_rfkill;
int type;
};
-const const struct ideapad_rfk_data ideapad_rfk_data[] = {
+static const struct ideapad_rfk_data ideapad_rfk_data[] = {
{ "ideapad_wlan", CFG_WIFI_BIT, VPCCMD_W_WIFI, RFKILL_TYPE_WLAN },
{ "ideapad_bluetooth", CFG_BT_BIT, VPCCMD_W_BT, RFKILL_TYPE_BLUETOOTH },
{ "ideapad_3g", CFG_3G_BIT, VPCCMD_W_3G, RFKILL_TYPE_WWAN },
{
unsigned long value;
- if (!priv->has_touchpad_control)
- return;
-
/* Without reading from EC touchpad LED doesn't switch state */
if (!read_ec_data(priv->adev->handle, VPCCMD_R_TOUCHPAD, &value)) {
/* Some IdeaPads don't really turn off touchpad - they only
* always results in 0 on these models, causing ideapad_laptop to wrongly
* report all radios as hardware-blocked.
*/
-static struct dmi_system_id no_hw_rfkill_list[] = {
- {
- .ident = "Lenovo Yoga 2 11 / 13 / Pro",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
- DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo Yoga 2"),
- },
- },
- {}
-};
-
-/*
- * Some models don't offer touchpad ctrl through the ideapad interface, causing
- * ideapad_sync_touchpad_state to send wrong touchpad enable/disable events.
- */
-static struct dmi_system_id no_touchpad_ctrl_list[] = {
- {
- .ident = "Lenovo Yoga 1 series",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
- DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo IdeaPad Yoga"),
- },
- },
+static const struct dmi_system_id no_hw_rfkill_list[] = {
{
.ident = "Lenovo Yoga 2 11 / 13 / Pro",
.matches = {
priv->adev = adev;
priv->platform_device = pdev;
priv->has_hw_rfkill_switch = !dmi_check_system(no_hw_rfkill_list);
- priv->has_touchpad_control = !dmi_check_system(no_touchpad_ctrl_list);
ret = ideapad_sysfs_init(priv);
if (ret)
const char *buf, size_t count)
{
struct toshiba_acpi_dev *toshiba = dev_get_drvdata(dev);
- int mode = -1;
- int time = -1;
+ int mode;
+ int time;
+ int ret;
- if (sscanf(buf, "%i", &mode) != 1 && (mode != 2 || mode != 1))
+
+ ret = kstrtoint(buf, 0, &mode);
+ if (ret)
+ return ret;
+ if (mode != SCI_KBD_MODE_FNZ && mode != SCI_KBD_MODE_AUTO)
return -EINVAL;
/* Set the Keyboard Backlight Mode where:
* Auto - KBD backlight turns off automatically in given time
* FN-Z - KBD backlight "toggles" when hotkey pressed
*/
- if (mode != -1 && toshiba->kbd_mode != mode) {
+ if (toshiba->kbd_mode != mode) {
time = toshiba->kbd_time << HCI_MISC_SHIFT;
time = time + toshiba->kbd_mode;
- if (toshiba_kbd_illum_status_set(toshiba, time) < 0)
- return -EIO;
+ ret = toshiba_kbd_illum_status_set(toshiba, time);
+ if (ret)
+ return ret;
toshiba->kbd_mode = mode;
}
{
struct toshiba_acpi_dev *dev = acpi_driver_data(to_acpi_device(device));
u32 result;
+ acpi_status status;
+
+ if (dev->hotkey_dev) {
+ status = acpi_evaluate_object(dev->acpi_dev->handle, "ENAB",
+ NULL, NULL);
+ if (ACPI_FAILURE(status))
+ pr_info("Unable to re-enable hotkeys\n");
- if (dev->hotkey_dev)
hci_write1(dev, HCI_HOTKEY_EVENT, HCI_HOTKEY_ENABLE, &result);
+ }
return 0;
}
info->device_type = s5m87xx->device_type;
info->wtsr_smpl = s5m87xx->wtsr_smpl;
- info->irq = regmap_irq_get_virq(s5m87xx->irq_data, alarm_irq);
- if (info->irq <= 0) {
- ret = -EINVAL;
- dev_err(&pdev->dev, "Failed to get virtual IRQ %d\n",
+ if (s5m87xx->irq_data) {
+ info->irq = regmap_irq_get_virq(s5m87xx->irq_data, alarm_irq);
+ if (info->irq <= 0) {
+ ret = -EINVAL;
+ dev_err(&pdev->dev, "Failed to get virtual IRQ %d\n",
alarm_irq);
- goto err;
+ goto err;
+ }
}
platform_set_drvdata(pdev, info);
goto err;
}
+ if (!info->irq) {
+ dev_info(&pdev->dev, "Alarm IRQ not available\n");
+ return 0;
+ }
+
ret = devm_request_threaded_irq(&pdev->dev, info->irq, NULL,
s5m_rtc_alarm_irq, 0, "rtc-alarm0",
info);
struct s5m_rtc_info *info = dev_get_drvdata(dev);
int ret = 0;
- if (device_may_wakeup(dev))
+ if (info->irq && device_may_wakeup(dev))
ret = disable_irq_wake(info->irq);
return ret;
struct s5m_rtc_info *info = dev_get_drvdata(dev);
int ret = 0;
- if (device_may_wakeup(dev))
+ if (info->irq && device_may_wakeup(dev))
ret = enable_irq_wake(info->irq);
return ret;
const unsigned char *buf, int count)
{
struct raw3215_info *raw;
+ int i, written;
if (!tty)
return 0;
raw = (struct raw3215_info *) tty->driver_data;
- raw3215_write(raw, buf, count);
- return count;
+ written = count;
+ while (count > 0) {
+ for (i = 0; i < count; i++)
+ if (buf[i] == '\t' || buf[i] == '\n')
+ break;
+ raw3215_write(raw, buf, i);
+ count -= i;
+ buf += i;
+ if (count > 0) {
+ raw3215_putchar(raw, *buf);
+ count--;
+ buf++;
+ }
+ }
+ return written;
}
/*
driver->subtype = SYSTEM_TYPE_TTY;
driver->init_termios = tty_std_termios;
driver->init_termios.c_iflag = IGNBRK | IGNPAR;
- driver->init_termios.c_oflag = ONLCR | XTABS;
+ driver->init_termios.c_oflag = ONLCR;
driver->init_termios.c_lflag = ISIG;
driver->flags = TTY_DRIVER_REAL_RAW;
tty_set_operations(driver, &tty3215_ops);
driver->subtype = SYSTEM_TYPE_TTY;
driver->init_termios = tty_std_termios;
driver->init_termios.c_iflag = IGNBRK | IGNPAR;
- driver->init_termios.c_oflag = ONLCR | XTABS;
+ driver->init_termios.c_oflag = ONLCR;
driver->init_termios.c_lflag = ISIG | ECHO;
driver->flags = TTY_DRIVER_REAL_RAW;
tty_set_operations(driver, &sclp_ops);
cmd->tag = req->tag;
- req->cmd = req->__cmd;
cmd->cmnd = req->cmd;
cmd->prot_op = SCSI_PROT_NORMAL;
spi_bitbang_stop(&hw->bitbang);
free_irq(hw->irq, hw);
iounmap((void __iomem *)hw->regs);
- release_mem_region(r->start, sizeof(psc_spi_t));
+ release_mem_region(hw->ioarea->start, sizeof(psc_spi_t));
if (hw->usedma) {
au1550_spi_dma_rxtmp_free(hw);
flags, dev_name(&spi->dev));
internal_cs = false;
}
- }
- if (retval) {
- dev_err(&spi->dev, "GPIO %d setup failed (%d)\n",
- spi->cs_gpio, retval);
- return retval;
- }
+ if (retval) {
+ dev_err(&spi->dev, "GPIO %d setup failed (%d)\n",
+ spi->cs_gpio, retval);
+ return retval;
+ }
- if (internal_cs)
- set_io_bits(dspi->base + SPIPC0, 1 << spi->chip_select);
+ if (internal_cs)
+ set_io_bits(dspi->base + SPIPC0, 1 << spi->chip_select);
+ }
if (spi->mode & SPI_READY)
set_io_bits(dspi->base + SPIPC0, SPIPC0_SPIENA_MASK);
if (ret)
return ret;
+ dws->regs = pcim_iomap_table(pdev)[pci_bar];
+
dws->bus_num = 0;
dws->num_cs = 4;
dws->irq = pdev->irq;
transfer_list);
if (!last_transfer->cs_change)
- spi_chip_sel(dws, dws->cur_msg->spi, 0);
+ spi_chip_sel(dws, msg->spi, 0);
spi_finalize_current_message(dws->master);
}
disable_fifo:
if (t->rx_buf != NULL)
chconf &= ~OMAP2_MCSPI_CHCONF_FFER;
- else
+
+ if (t->tx_buf != NULL)
chconf &= ~OMAP2_MCSPI_CHCONF_FFET;
mcspi_write_chconf0(spi, chconf);
{ "INT3430", 0 },
{ "INT3431", 0 },
{ "80860F0E", 0 },
+ { "8086228E", 0 },
{ },
};
MODULE_DEVICE_TABLE(acpi, pxa2xx_spi_acpi_match);
}
/* div doesn't support odd number */
- div = rs->max_freq / rs->speed;
+ div = max_t(u32, rs->max_freq / rs->speed, 1);
div = (div + 1) & 0xfffe;
spi_enable_chip(rs, 0);
rs->dma_tx.addr = (dma_addr_t)(mem->start + ROCKCHIP_SPI_TXDR);
rs->dma_rx.addr = (dma_addr_t)(mem->start + ROCKCHIP_SPI_RXDR);
rs->dma_tx.direction = DMA_MEM_TO_DEV;
- rs->dma_tx.direction = DMA_DEV_TO_MEM;
+ rs->dma_rx.direction = DMA_DEV_TO_MEM;
master->can_dma = rockchip_spi_can_dma;
master->dma_tx = rs->dma_tx.ch;
dma_cookie_t cookie;
int ret;
- if (tx) {
- desc_tx = dmaengine_prep_slave_sg(rspi->master->dma_tx,
- tx->sgl, tx->nents, DMA_TO_DEVICE,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc_tx)
- goto no_dma;
-
- irq_mask |= SPCR_SPTIE;
- }
+ /* First prepare and submit the DMA request(s), as this may fail */
if (rx) {
desc_rx = dmaengine_prep_slave_sg(rspi->master->dma_rx,
rx->sgl, rx->nents, DMA_FROM_DEVICE,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc_rx)
- goto no_dma;
+ if (!desc_rx) {
+ ret = -EAGAIN;
+ goto no_dma_rx;
+ }
+
+ desc_rx->callback = rspi_dma_complete;
+ desc_rx->callback_param = rspi;
+ cookie = dmaengine_submit(desc_rx);
+ if (dma_submit_error(cookie)) {
+ ret = cookie;
+ goto no_dma_rx;
+ }
irq_mask |= SPCR_SPRIE;
}
+ if (tx) {
+ desc_tx = dmaengine_prep_slave_sg(rspi->master->dma_tx,
+ tx->sgl, tx->nents, DMA_TO_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc_tx) {
+ ret = -EAGAIN;
+ goto no_dma_tx;
+ }
+
+ if (rx) {
+ /* No callback */
+ desc_tx->callback = NULL;
+ } else {
+ desc_tx->callback = rspi_dma_complete;
+ desc_tx->callback_param = rspi;
+ }
+ cookie = dmaengine_submit(desc_tx);
+ if (dma_submit_error(cookie)) {
+ ret = cookie;
+ goto no_dma_tx;
+ }
+
+ irq_mask |= SPCR_SPTIE;
+ }
+
/*
* DMAC needs SPxIE, but if SPxIE is set, the IRQ routine will be
* called. So, this driver disables the IRQ while DMA transfer.
rspi_enable_irq(rspi, irq_mask);
rspi->dma_callbacked = 0;
- if (rx) {
- desc_rx->callback = rspi_dma_complete;
- desc_rx->callback_param = rspi;
- cookie = dmaengine_submit(desc_rx);
- if (dma_submit_error(cookie))
- return cookie;
+ /* Now start DMA */
+ if (rx)
dma_async_issue_pending(rspi->master->dma_rx);
- }
- if (tx) {
- if (rx) {
- /* No callback */
- desc_tx->callback = NULL;
- } else {
- desc_tx->callback = rspi_dma_complete;
- desc_tx->callback_param = rspi;
- }
- cookie = dmaengine_submit(desc_tx);
- if (dma_submit_error(cookie))
- return cookie;
+ if (tx)
dma_async_issue_pending(rspi->master->dma_tx);
- }
ret = wait_event_interruptible_timeout(rspi->wait,
rspi->dma_callbacked, HZ);
if (ret > 0 && rspi->dma_callbacked)
ret = 0;
- else if (!ret)
+ else if (!ret) {
+ dev_err(&rspi->master->dev, "DMA timeout\n");
ret = -ETIMEDOUT;
+ if (tx)
+ dmaengine_terminate_all(rspi->master->dma_tx);
+ if (rx)
+ dmaengine_terminate_all(rspi->master->dma_rx);
+ }
rspi_disable_irq(rspi, irq_mask);
return ret;
-no_dma:
- pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
- dev_driver_string(&rspi->master->dev),
- dev_name(&rspi->master->dev));
- return -EAGAIN;
+no_dma_tx:
+ if (rx)
+ dmaengine_terminate_all(rspi->master->dma_rx);
+no_dma_rx:
+ if (ret == -EAGAIN) {
+ pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
+ dev_driver_string(&rspi->master->dev),
+ dev_name(&rspi->master->dev));
+ }
+ return ret;
}
static void rspi_receive_init(const struct rspi_data *rspi)
dma_cookie_t cookie;
int ret;
- if (tx) {
- ier_bits |= IER_TDREQE | IER_TDMAE;
- dma_sync_single_for_device(p->master->dma_tx->device->dev,
- p->tx_dma_addr, len, DMA_TO_DEVICE);
- desc_tx = dmaengine_prep_slave_single(p->master->dma_tx,
- p->tx_dma_addr, len, DMA_TO_DEVICE,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc_tx)
- return -EAGAIN;
- }
-
+ /* First prepare and submit the DMA request(s), as this may fail */
if (rx) {
ier_bits |= IER_RDREQE | IER_RDMAE;
desc_rx = dmaengine_prep_slave_single(p->master->dma_rx,
p->rx_dma_addr, len, DMA_FROM_DEVICE,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc_rx)
- return -EAGAIN;
- }
-
- /* 1 stage FIFO watermarks for DMA */
- sh_msiof_write(p, FCTR, FCTR_TFWM_1 | FCTR_RFWM_1);
-
- /* setup msiof transfer mode registers (32-bit words) */
- sh_msiof_spi_set_mode_regs(p, tx, rx, 32, len / 4);
-
- sh_msiof_write(p, IER, ier_bits);
-
- reinit_completion(&p->done);
+ if (!desc_rx) {
+ ret = -EAGAIN;
+ goto no_dma_rx;
+ }
- if (rx) {
desc_rx->callback = sh_msiof_dma_complete;
desc_rx->callback_param = p;
cookie = dmaengine_submit(desc_rx);
if (dma_submit_error(cookie)) {
ret = cookie;
- goto stop_ier;
+ goto no_dma_rx;
}
- dma_async_issue_pending(p->master->dma_rx);
}
if (tx) {
+ ier_bits |= IER_TDREQE | IER_TDMAE;
+ dma_sync_single_for_device(p->master->dma_tx->device->dev,
+ p->tx_dma_addr, len, DMA_TO_DEVICE);
+ desc_tx = dmaengine_prep_slave_single(p->master->dma_tx,
+ p->tx_dma_addr, len, DMA_TO_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc_tx) {
+ ret = -EAGAIN;
+ goto no_dma_tx;
+ }
+
if (rx) {
/* No callback */
desc_tx->callback = NULL;
cookie = dmaengine_submit(desc_tx);
if (dma_submit_error(cookie)) {
ret = cookie;
- goto stop_rx;
+ goto no_dma_tx;
}
- dma_async_issue_pending(p->master->dma_tx);
}
+ /* 1 stage FIFO watermarks for DMA */
+ sh_msiof_write(p, FCTR, FCTR_TFWM_1 | FCTR_RFWM_1);
+
+ /* setup msiof transfer mode registers (32-bit words) */
+ sh_msiof_spi_set_mode_regs(p, tx, rx, 32, len / 4);
+
+ sh_msiof_write(p, IER, ier_bits);
+
+ reinit_completion(&p->done);
+
+ /* Now start DMA */
+ if (rx)
+ dma_async_issue_pending(p->master->dma_rx);
+ if (tx)
+ dma_async_issue_pending(p->master->dma_tx);
+
ret = sh_msiof_spi_start(p, rx);
if (ret) {
dev_err(&p->pdev->dev, "failed to start hardware\n");
- goto stop_tx;
+ goto stop_dma;
}
/* wait for tx fifo to be emptied / rx fifo to be filled */
stop_reset:
sh_msiof_reset_str(p);
sh_msiof_spi_stop(p, rx);
-stop_tx:
+stop_dma:
if (tx)
dmaengine_terminate_all(p->master->dma_tx);
-stop_rx:
+no_dma_tx:
if (rx)
dmaengine_terminate_all(p->master->dma_rx);
-stop_ier:
sh_msiof_write(p, IER, 0);
+no_dma_rx:
return ret;
}
/**
* spi_finalize_current_transfer - report completion of a transfer
+ * @master: the master reporting completion
*
* Called by SPI drivers using the core transfer_one_message()
* implementation to notify it that the current interrupt driven
source "drivers/staging/slicoss/Kconfig"
-source "drivers/staging/usbip/Kconfig"
-
source "drivers/staging/wlan-ng/Kconfig"
source "drivers/staging/comedi/Kconfig"
obj-y += media/
obj-$(CONFIG_ET131X) += et131x/
obj-$(CONFIG_SLICOSS) += slicoss/
-obj-$(CONFIG_USBIP_CORE) += usbip/
obj-$(CONFIG_PRISM2_USB) += wlan-ng/
obj-$(CONFIG_COMEDI) += comedi/
obj-$(CONFIG_FB_OLPC_DCON) += olpc_dcon/
if (unlikely(ret)) {
pr_err("failed to register misc device for log '%s'!\n",
log->misc.name);
- goto out_free_log;
+ goto out_free_misc_name;
}
pr_info("created %luK log '%s'\n",
return 0;
+out_free_misc_name:
+ kfree(log->misc.name);
+
out_free_log:
kfree(log);
* @reg: the register to read
* @value: 16-bit value to write
*/
-static int et131x_mii_write(struct et131x_adapter *adapter, u8 reg, u16 value)
+static int et131x_mii_write(struct et131x_adapter *adapter, u8 addr, u8 reg,
+ u16 value)
{
struct mac_regs __iomem *mac = &adapter->regs->mac;
- struct phy_device *phydev = adapter->phydev;
int status = 0;
- u8 addr;
u32 delay = 0;
u32 mii_addr;
u32 mii_cmd;
u32 mii_indicator;
- if (!phydev)
- return -EIO;
-
- addr = phydev->addr;
-
/* Save a local copy of the registers we are dealing with so we can
* set them back
*/
struct net_device *netdev = bus->priv;
struct et131x_adapter *adapter = netdev_priv(netdev);
- return et131x_mii_write(adapter, reg, value);
-}
-
-static int et131x_mdio_reset(struct mii_bus *bus)
-{
- struct net_device *netdev = bus->priv;
- struct et131x_adapter *adapter = netdev_priv(netdev);
-
- et131x_mii_write(adapter, MII_BMCR, BMCR_RESET);
-
- return 0;
+ return et131x_mii_write(adapter, phy_addr, reg, value);
}
/* et1310_phy_power_switch - PHY power control
static void et1310_phy_power_switch(struct et131x_adapter *adapter, bool down)
{
u16 data;
+ struct phy_device *phydev = adapter->phydev;
et131x_mii_read(adapter, MII_BMCR, &data);
data &= ~BMCR_PDOWN;
if (down)
data |= BMCR_PDOWN;
- et131x_mii_write(adapter, MII_BMCR, data);
+ et131x_mii_write(adapter, phydev->addr, MII_BMCR, data);
}
/* et131x_xcvr_init - Init the phy if we are setting it into force mode */
static void et131x_xcvr_init(struct et131x_adapter *adapter)
{
u16 lcr2;
+ struct phy_device *phydev = adapter->phydev;
/* Set the LED behavior such that LED 1 indicates speed (off =
* 10Mbits, blink = 100Mbits, on = 1000Mbits) and LED 2 indicates
else
lcr2 |= (LED_VAL_LINKON << LED_TXRX_SHIFT);
- et131x_mii_write(adapter, PHY_LED_2, lcr2);
+ et131x_mii_write(adapter, phydev->addr, PHY_LED_2, lcr2);
}
}
et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
®ister18);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18 | 0x4);
- et131x_mii_write(adapter, PHY_INDEX_REG,
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18 | 0x4);
+ et131x_mii_write(adapter, phydev->addr, PHY_INDEX_REG,
register18 | 0x8402);
- et131x_mii_write(adapter, PHY_DATA_REG,
+ et131x_mii_write(adapter, phydev->addr, PHY_DATA_REG,
register18 | 511);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18);
}
et1310_config_flow_control(adapter);
et131x_mii_read(adapter, PHY_CONFIG, ®);
reg &= ~ET_PHY_CONFIG_TX_FIFO_DEPTH;
reg |= ET_PHY_CONFIG_FIFO_DEPTH_32;
- et131x_mii_write(adapter, PHY_CONFIG, reg);
+ et131x_mii_write(adapter, phydev->addr, PHY_CONFIG,
+ reg);
}
et131x_set_rx_dma_timer(adapter);
et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
®ister18);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18 | 0x4);
- et131x_mii_write(adapter, PHY_INDEX_REG,
- register18 | 0x8402);
- et131x_mii_write(adapter, PHY_DATA_REG,
- register18 | 511);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18 | 0x4);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_INDEX_REG, register18 | 0x8402);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_DATA_REG, register18 | 511);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18);
}
/* Free the packets being actively sent & stopped */
/* Copy address into the net_device struct */
memcpy(netdev->dev_addr, adapter->addr, ETH_ALEN);
- /* Init variable for counting how long we do not have link status */
- adapter->boot_coma = 0;
- et1310_disable_phy_coma(adapter);
-
rc = -ENOMEM;
/* Setup the mii_bus struct */
adapter->mii_bus->priv = netdev;
adapter->mii_bus->read = et131x_mdio_read;
adapter->mii_bus->write = et131x_mdio_write;
- adapter->mii_bus->reset = et131x_mdio_reset;
adapter->mii_bus->irq = kmalloc_array(PHY_MAX_ADDR, sizeof(int),
GFP_KERNEL);
if (!adapter->mii_bus->irq)
/* Setup et1310 as per the documentation */
et131x_adapter_setup(adapter);
+ /* Init variable for counting how long we do not have link status */
+ adapter->boot_coma = 0;
+ et1310_disable_phy_coma(adapter);
+
/* We can enable interrupts now
*
* NOTE - Because registration of interrupt handler is done in the
return -ENOMEM;
strncpy(sched->ws_name, name, CFS_WS_NAME_LEN);
+ sched->ws_name[CFS_WS_NAME_LEN - 1] = '\0';
sched->ws_cptab = cptab;
sched->ws_cpt = cpt;
*/
#define DEBUG_SUBSYSTEM S_CLASS
-# include <asm/atomic.h>
+# include <linux/atomic.h>
#include "../include/obd_support.h"
#include "../include/obd_class.h"
{USB_DEVICE(USB_VENDER_ID_REALTEK, 0x0179)}, /* 8188ETV */
/*=== Customer ID ===*/
/****** 8188EUS ********/
+ {USB_DEVICE(0x056e, 0x4008)}, /* Elecom WDC-150SU2M */
{USB_DEVICE(0x07b8, 0x8179)}, /* Abocom - Abocom */
{USB_DEVICE(0x2001, 0x330F)}, /* DLink DWA-125 REV D1 */
{USB_DEVICE(0x2001, 0x3310)}, /* Dlink DWA-123 REV D1 */
+ {USB_DEVICE(0x0df6, 0x0076)}, /* Sitecom N150 v2 */
{} /* Terminating entry */
};
/* Activate hops. */
for (i = path->path_length - 1; i >= 0; i--) {
- struct tb_regs_hop hop;
+ struct tb_regs_hop hop = { 0 };
+
+ /*
+ * We do (currently) not tear down paths setup by the firmeware.
+ * If a firmware device is unplugged and plugged in again then
+ * it can happen that we reuse some of the hops from the (now
+ * defunct) firmeware path. This causes the hotplug operation to
+ * fail (the pci device does not show up). Clearing the hop
+ * before overwriting it fixes the problem.
+ *
+ * Should be removed once we discover and tear down firmeware
+ * paths.
+ */
+ res = tb_port_write(path->hops[i].in_port, &hop, TB_CFG_HOPS,
+ 2 * path->hops[i].in_hop_index, 2);
+ if (res) {
+ __tb_path_deactivate_hops(path, i);
+ __tb_path_deallocate_nfc(path, 0);
+ goto err;
+ }
/* dword 0 */
hop.next_hop = path->hops[i].next_hop_index;
source "drivers/usb/image/Kconfig"
+source "drivers/usb/usbip/Kconfig"
+
endif
source "drivers/usb/musb/Kconfig"
obj-$(CONFIG_USB_GADGET) += gadget/
obj-$(CONFIG_USB_COMMON) += common/
+
+obj-$(CONFIG_USBIP_CORE) += usbip/
* - Change autosuspend delay of hub can avoid unnecessary auto
* suspend timer for hub, also may decrease power consumption
* of USB bus.
+ *
+ * - If user has indicated to prevent autosuspend by passing
+ * usbcore.autosuspend = -1 then keep autosuspend disabled.
*/
- pm_runtime_set_autosuspend_delay(&hdev->dev, 0);
+#ifdef CONFIG_PM_RUNTIME
+ if (hdev->dev.power.autosuspend_delay >= 0)
+ pm_runtime_set_autosuspend_delay(&hdev->dev, 0);
+#endif
/*
* Hubs have proper suspend/resume support, except for root hubs
{
struct usb_port *port_dev = NULL;
struct usb_device *udev = *pdev;
- struct usb_hub *hub;
- int port1;
+ struct usb_hub *hub = NULL;
+ int port1 = 1;
/* mark the device as inactive, so any further urb submissions for
* this device (and any of its children) will fail immediately.
if (status != -ENODEV &&
port1 != unreliable_port &&
printk_ratelimit())
- dev_err(&udev->dev, "connect-debounce failed, port %d disabled\n",
- port1);
-
+ dev_err(&port_dev->dev, "connect-debounce failed\n");
portstatus &= ~USB_PORT_STAT_CONNECTION;
unreliable_port = port1;
} else {
static void s3c_hsotg_irq_enumdone(struct s3c_hsotg *hsotg)
{
u32 dsts = readl(hsotg->regs + DSTS);
- int ep0_mps = 0, ep_mps;
+ int ep0_mps = 0, ep_mps = 8;
/*
* This should signal the finish of the enumeration phase
static int dwc3_omap_extcon_register(struct dwc3_omap *omap)
{
- u32 ret;
+ int ret;
struct device_node *node = omap->dev->of_node;
struct extcon_dev *edev;
#
subdir-ccflags-$(CONFIG_USB_GADGET_DEBUG) := -DDEBUG
subdir-ccflags-$(CONFIG_USB_GADGET_VERBOSE) += -DVERBOSE_DEBUG
-ccflags-y += -I$(PWD)/drivers/usb/gadget/udc
+ccflags-y += -Idrivers/usb/gadget/udc
obj-$(CONFIG_USB_LIBCOMPOSITE) += libcomposite.o
libcomposite-y := usbstring.o config.o epautoconf.o
# USB peripheral controller drivers
#
-ccflags-y := -I$(PWD)/drivers/usb/gadget/
-ccflags-y += -I$(PWD)/drivers/usb/gadget/udc/
+ccflags-y := -Idrivers/usb/gadget/
+ccflags-y += -Idrivers/usb/gadget/udc/
# USB Functions
usb_f_acm-y := f_acm.o
DBG(dev, "%s\n", __func__);
- netif_tx_lock(dev->net);
netif_stop_queue(dev->net);
- netif_tx_unlock(dev->net);
-
netif_carrier_off(dev->net);
/* disable endpoints, forcing (synchronous) completion
printk(KERN_INFO "Failed to queue request (%d).\n", ret);
usb_ep_set_halt(ep);
spin_unlock_irqrestore(&video->queue.irqlock, flags);
+ uvc_queue_cancel(queue, 0);
goto requeue;
}
spin_unlock_irqrestore(&video->queue.irqlock, flags);
static int
uvc_video_pump(struct uvc_video *video)
{
+ struct uvc_video_queue *queue = &video->queue;
struct usb_request *req;
struct uvc_buffer *buf;
unsigned long flags;
printk(KERN_INFO "Failed to queue request (%d)\n", ret);
usb_ep_set_halt(video->ep);
spin_unlock_irqrestore(&video->queue.irqlock, flags);
+ uvc_queue_cancel(queue, 0);
break;
}
spin_unlock_irqrestore(&video->queue.irqlock, flags);
# USB gadget drivers
#
-ccflags-y := -I$(PWD)/drivers/usb/gadget/
-ccflags-y += -I$(PWD)/drivers/usb/gadget/udc/
-ccflags-y += -I$(PWD)/drivers/usb/gadget/function/
+ccflags-y := -Idrivers/usb/gadget/
+ccflags-y += -Idrivers/usb/gadget/udc/
+ccflags-y += -Idrivers/usb/gadget/function/
g_zero-y := zero.o
g_audio-y := audio.o
{
#ifdef CONFIG_USB_G_DBGP_SERIAL
kfree(dbgp.serial);
+ dbgp.serial = NULL;
#endif
if (dbgp.req) {
kfree(dbgp.req->buf);
usb_ep_free_request(gadget->ep0, dbgp.req);
+ dbgp.req = NULL;
}
gadget->ep0->driver_data = NULL;
value = -ENOMEM;
kbuf = memdup_user(buf, len);
- if (!kbuf) {
+ if (IS_ERR(kbuf)) {
value = PTR_ERR(kbuf);
goto free1;
}
gadget drivers to also be dynamically linked.
config USB_EG20T
- tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7213/ML7831) UDC"
+ tristate "Intel QUARK X1000/EG20T PCH/LAPIS Semiconductor IOH(ML7213/ML7831) UDC"
depends on PCI
help
This is a USB device driver for EG20T PCH.
ML7213/ML7831 is companion chip for Intel Atom E6xx series.
ML7213/ML7831 is completely compatible for Intel EG20T PCH.
+ This driver can be used with Intel's Quark X1000 SOC platform
#
# LAST -- dummy/emulated controller
#
if (dma_status) {
int i;
- for (i = 1; i < USBA_NR_DMAS; i++)
+ for (i = 1; i <= USBA_NR_DMAS; i++)
if (dma_status & (1 << i))
usba_dma_irq(udc, &udc->usba_ep[i]);
}
/* initialize udc */
fusb300 = kzalloc(sizeof(struct fusb300), GFP_KERNEL);
- if (fusb300 == NULL)
+ if (fusb300 == NULL) {
+ ret = -ENOMEM;
goto clean_up;
+ }
for (i = 0; i < FUSB300_MAX_NUM_EP; i++) {
_ep[i] = kzalloc(sizeof(struct fusb300_ep), GFP_KERNEL);
- if (_ep[i] == NULL)
+ if (_ep[i] == NULL) {
+ ret = -ENOMEM;
goto clean_up;
+ }
fusb300->ep[i] = _ep[i];
}
* @setup_data: Received setup data
* @phys_addr: of device memory
* @base_addr: for mapped device memory
+ * @bar: Indicates which PCI BAR for USB regs
* @irq: IRQ line for the device
* @cfg_data: current cfg, intf, and alt in use
* @vbus_gpio: GPIO informaton for detecting VBUS
struct usb_ctrlrequest setup_data;
unsigned long phys_addr;
void __iomem *base_addr;
+ unsigned bar;
unsigned irq;
struct pch_udc_cfg_data cfg_data;
struct pch_vbus_gpio_data vbus_gpio;
};
#define to_pch_udc(g) (container_of((g), struct pch_udc_dev, gadget))
+#define PCH_UDC_PCI_BAR_QUARK_X1000 0
#define PCH_UDC_PCI_BAR 1
#define PCI_DEVICE_ID_INTEL_EG20T_UDC 0x8808
+#define PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC 0x0939
#define PCI_VENDOR_ID_ROHM 0x10DB
#define PCI_DEVICE_ID_ML7213_IOH_UDC 0x801D
#define PCI_DEVICE_ID_ML7831_IOH_UDC 0x8808
iounmap(dev->base_addr);
if (dev->mem_region)
release_mem_region(dev->phys_addr,
- pci_resource_len(pdev, PCH_UDC_PCI_BAR));
+ pci_resource_len(pdev, dev->bar));
if (dev->active)
pci_disable_device(pdev);
kfree(dev);
dev->active = 1;
pci_set_drvdata(pdev, dev);
+ /* Determine BAR based on PCI ID */
+ if (id->device == PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC)
+ dev->bar = PCH_UDC_PCI_BAR_QUARK_X1000;
+ else
+ dev->bar = PCH_UDC_PCI_BAR;
+
/* PCI resource allocation */
- resource = pci_resource_start(pdev, 1);
- len = pci_resource_len(pdev, 1);
+ resource = pci_resource_start(pdev, dev->bar);
+ len = pci_resource_len(pdev, dev->bar);
if (!request_mem_region(resource, len, KBUILD_MODNAME)) {
dev_err(&pdev->dev, "%s: pci device used already\n", __func__);
static const struct pci_device_id pch_udc_pcidev_id[] = {
{
+ PCI_DEVICE(PCI_VENDOR_ID_INTEL,
+ PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC),
+ .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe,
+ .class_mask = 0xffffffff,
+ },
+ {
PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EG20T_UDC),
.class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe,
.class_mask = 0xffffffff,
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
reg = devm_ioremap_resource(&pdev->dev, res);
- if (!reg)
- return -ENODEV;
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
ires = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
irq = ires->start;
if (selector == EHSET_TEST_SINGLE_STEP_SET_FEATURE) {
spin_unlock_irqrestore(&ehci->lock, flags);
retval = ehset_single_step_set_feature(hcd,
- wIndex);
+ wIndex + 1);
spin_lock_irqsave(&ehci->lock, flags);
break;
}
/* AMD PLL quirk */
if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
xhci->quirks |= XHCI_AMD_PLL_FIX;
+
+ if (pdev->vendor == PCI_VENDOR_ID_AMD)
+ xhci->quirks |= XHCI_TRUST_TX_LENGTH;
+
if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
xhci->quirks |= XHCI_LPM_SUPPORT;
xhci->quirks |= XHCI_INTEL_HOST;
if (pdev->vendor == PCI_VENDOR_ID_VIA)
xhci->quirks |= XHCI_RESET_ON_RESUME;
+ /* See https://bugzilla.kernel.org/show_bug.cgi?id=79511 */
+ if (pdev->vendor == PCI_VENDOR_ID_VIA &&
+ pdev->device == 0x3432)
+ xhci->quirks |= XHCI_BROKEN_STREAMS;
+
if (xhci->quirks & XHCI_RESET_ON_RESUME)
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Resetting on resume");
}
}
-/*
- * Find the segment that trb is in. Start searching in start_seg.
- * If we must move past a segment that has a link TRB with a toggle cycle state
- * bit set, then we will toggle the value pointed at by cycle_state.
- */
-static struct xhci_segment *find_trb_seg(
- struct xhci_segment *start_seg,
- union xhci_trb *trb, int *cycle_state)
-{
- struct xhci_segment *cur_seg = start_seg;
- struct xhci_generic_trb *generic_trb;
-
- while (cur_seg->trbs > trb ||
- &cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) {
- generic_trb = &cur_seg->trbs[TRBS_PER_SEGMENT - 1].generic;
- if (generic_trb->field[3] & cpu_to_le32(LINK_TOGGLE))
- *cycle_state ^= 0x1;
- cur_seg = cur_seg->next;
- if (cur_seg == start_seg)
- /* Looped over the entire list. Oops! */
- return NULL;
- }
- return cur_seg;
-}
-
-
static struct xhci_ring *xhci_triad_to_transfer_ring(struct xhci_hcd *xhci,
unsigned int slot_id, unsigned int ep_index,
unsigned int stream_id)
struct xhci_virt_device *dev = xhci->devs[slot_id];
struct xhci_virt_ep *ep = &dev->eps[ep_index];
struct xhci_ring *ep_ring;
- struct xhci_generic_trb *trb;
+ struct xhci_segment *new_seg;
+ union xhci_trb *new_deq;
dma_addr_t addr;
u64 hw_dequeue;
+ bool cycle_found = false;
+ bool td_last_trb_found = false;
ep_ring = xhci_triad_to_transfer_ring(xhci, slot_id,
ep_index, stream_id);
hw_dequeue = le64_to_cpu(ep_ctx->deq);
}
- /* Find virtual address and segment of hardware dequeue pointer */
- state->new_deq_seg = ep_ring->deq_seg;
- state->new_deq_ptr = ep_ring->dequeue;
- while (xhci_trb_virt_to_dma(state->new_deq_seg, state->new_deq_ptr)
- != (dma_addr_t)(hw_dequeue & ~0xf)) {
- next_trb(xhci, ep_ring, &state->new_deq_seg,
- &state->new_deq_ptr);
- if (state->new_deq_ptr == ep_ring->dequeue) {
- WARN_ON(1);
- return;
- }
- }
+ new_seg = ep_ring->deq_seg;
+ new_deq = ep_ring->dequeue;
+ state->new_cycle_state = hw_dequeue & 0x1;
+
/*
- * Find cycle state for last_trb, starting at old cycle state of
- * hw_dequeue. If there is only one segment ring, find_trb_seg() will
- * return immediately and cannot toggle the cycle state if this search
- * wraps around, so add one more toggle manually in that case.
+ * We want to find the pointer, segment and cycle state of the new trb
+ * (the one after current TD's last_trb). We know the cycle state at
+ * hw_dequeue, so walk the ring until both hw_dequeue and last_trb are
+ * found.
*/
- state->new_cycle_state = hw_dequeue & 0x1;
- if (ep_ring->first_seg == ep_ring->first_seg->next &&
- cur_td->last_trb < state->new_deq_ptr)
- state->new_cycle_state ^= 0x1;
+ do {
+ if (!cycle_found && xhci_trb_virt_to_dma(new_seg, new_deq)
+ == (dma_addr_t)(hw_dequeue & ~0xf)) {
+ cycle_found = true;
+ if (td_last_trb_found)
+ break;
+ }
+ if (new_deq == cur_td->last_trb)
+ td_last_trb_found = true;
- state->new_deq_ptr = cur_td->last_trb;
- xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
- "Finding segment containing last TRB in TD.");
- state->new_deq_seg = find_trb_seg(state->new_deq_seg,
- state->new_deq_ptr, &state->new_cycle_state);
- if (!state->new_deq_seg) {
- WARN_ON(1);
- return;
- }
+ if (cycle_found &&
+ TRB_TYPE_LINK_LE32(new_deq->generic.field[3]) &&
+ new_deq->generic.field[3] & cpu_to_le32(LINK_TOGGLE))
+ state->new_cycle_state ^= 0x1;
+
+ next_trb(xhci, ep_ring, &new_seg, &new_deq);
+
+ /* Search wrapped around, bail out */
+ if (new_deq == ep->ring->dequeue) {
+ xhci_err(xhci, "Error: Failed finding new dequeue state\n");
+ state->new_deq_seg = NULL;
+ state->new_deq_ptr = NULL;
+ return;
+ }
+
+ } while (!cycle_found || !td_last_trb_found);
- /* Increment to find next TRB after last_trb. Cycle if appropriate. */
- trb = &state->new_deq_ptr->generic;
- if (TRB_TYPE_LINK_LE32(trb->field[3]) &&
- (trb->field[3] & cpu_to_le32(LINK_TOGGLE)))
- state->new_cycle_state ^= 0x1;
- next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr);
+ state->new_deq_seg = new_seg;
+ state->new_deq_ptr = new_deq;
/* Don't update the ring cycle state for the producer (us). */
xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
* last TRB of the previous TD. The command completion handle
* will take care the rest.
*/
- if (!event_seg && trb_comp_code == COMP_STOP_INVAL) {
+ if (!event_seg && (trb_comp_code == COMP_STOP ||
+ trb_comp_code == COMP_STOP_INVAL)) {
ret = 0;
goto cleanup;
}
ep_index, ep->stopped_stream, ep->stopped_td,
&deq_state);
+ if (!deq_state.new_deq_ptr || !deq_state.new_deq_seg)
+ return;
+
/* HW with the reset endpoint quirk will use the saved dequeue state to
* issue a configure endpoint command later.
*/
{ USB_DEVICE(0x0711, 0x0918) },
{ USB_DEVICE(0x0711, 0x0920) },
{ USB_DEVICE(0x0711, 0x0950) },
+ { USB_DEVICE(0x0711, 0x5200) },
{ USB_DEVICE(0x182d, 0x021c) },
{ USB_DEVICE(0x182d, 0x0269) },
{ }
struct musb *musb = ux500_channel->controller->private_data;
dev_dbg(musb->controller,
- "packet_sz=%d, mode=%d, dma_addr=0x%llu, len=%d is_tx=%d\n",
+ "packet_sz=%d, mode=%d, dma_addr=0x%llx, len=%d is_tx=%d\n",
packet_sz, mode, (unsigned long long) dma_addr,
len, ux500_channel->is_tx);
gpio_vbus->phy.otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
GFP_KERNEL);
- if (!gpio_vbus->phy.otg) {
- kfree(gpio_vbus);
+ if (!gpio_vbus->phy.otg)
return -ENOMEM;
- }
platform_set_drvdata(pdev, gpio_vbus);
gpio_vbus->dev = &pdev->dev;
*/
if (motg->phy_number) {
phy_select = devm_ioremap_nocache(&pdev->dev, USB2_PHY_SEL, 4);
- if (IS_ERR(phy_select))
- return PTR_ERR(phy_select);
+ if (!phy_select)
+ return -ENOMEM;
/* Enable second PHY with the OTG port */
writel(0x1, phy_select);
}
#define EXYNOS5_DRD_PHYPARAM1 (0x20)
-#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
+#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x3f << 0)
#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
#define EXYNOS5_DRD_PHYTERM (0x24)
phy = __usb_find_phy_dev(dev, &phy_bind_list, index);
if (IS_ERR(phy) || !try_module_get(phy->dev->driver->owner)) {
dev_dbg(dev, "unable to find transceiver\n");
+ if (!IS_ERR(phy))
+ phy = ERR_PTR(-ENODEV);
+
goto err0;
}
{ USB_DEVICE(FTDI_VID, FTDI_AMC232_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CANUSB_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CANDAPTER_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_BM_ATOM_NANO_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_NXTCAM_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_EV3CON_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_0_PID) },
{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_2_PID) },
{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_3_PID) },
{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_4_PID) },
+ /* ekey Devices */
+ { USB_DEVICE(FTDI_VID, FTDI_EKEY_CONV_USB_PID) },
/* Infineon Devices */
{ USB_DEVICE_INTERFACE_NUMBER(INFINEON_VID, INFINEON_TRIBOARD_PID, 1) },
{ } /* Terminating entry */
/* www.candapter.com Ewert Energy Systems CANdapter device */
#define FTDI_CANDAPTER_PID 0x9F80 /* Product Id */
+#define FTDI_BM_ATOM_NANO_PID 0xa559 /* Basic Micro ATOM Nano USB2Serial */
+
/*
* Texas Instruments XDS100v2 JTAG / BeagleBone A3
* http://processors.wiki.ti.com/index.php/XDS100
#define BRAINBOXES_US_160_6_PID 0x9006 /* US-160 16xRS232 1Mbaud Port 11 and 12 */
#define BRAINBOXES_US_160_7_PID 0x9007 /* US-160 16xRS232 1Mbaud Port 13 and 14 */
#define BRAINBOXES_US_160_8_PID 0x9008 /* US-160 16xRS232 1Mbaud Port 15 and 16 */
+
+/*
+ * ekey biometric systems GmbH (http://ekey.net/)
+ */
+#define FTDI_EKEY_CONV_USB_PID 0xCB08 /* Converter USB */
#define ZTE_PRODUCT_MF622 0x0001
#define ZTE_PRODUCT_MF628 0x0015
#define ZTE_PRODUCT_MF626 0x0031
-#define ZTE_PRODUCT_MC2718 0xffe8
#define ZTE_PRODUCT_AC2726 0xfff1
+#define ZTE_PRODUCT_CDMA_TECH 0xfffe
+#define ZTE_PRODUCT_AC8710T 0xffff
+#define ZTE_PRODUCT_MC2718 0xffe8
+#define ZTE_PRODUCT_AD3812 0xffeb
+#define ZTE_PRODUCT_MC2716 0xffed
#define BENQ_VENDOR_ID 0x04a5
#define BENQ_PRODUCT_H10 0x4068
#define INOVIA_VENDOR_ID 0x20a6
#define INOVIA_SEW858 0x1105
+/* VIA Telecom */
+#define VIATELECOM_VENDOR_ID 0x15eb
+#define VIATELECOM_PRODUCT_CDS7 0x0001
+
/* some devices interfaces need special handling due to a number of reasons */
enum option_blacklist_reason {
OPTION_BLACKLIST_NONE = 0,
.reserved = BIT(4),
};
+static const struct option_blacklist_info zte_ad3812_z_blacklist = {
+ .sendsetup = BIT(0) | BIT(1) | BIT(2),
+};
+
static const struct option_blacklist_info zte_mc2718_z_blacklist = {
.sendsetup = BIT(1) | BIT(2) | BIT(3) | BIT(4),
};
+static const struct option_blacklist_info zte_mc2716_z_blacklist = {
+ .sendsetup = BIT(1) | BIT(2) | BIT(3),
+};
+
static const struct option_blacklist_info huawei_cdc12_blacklist = {
.reserved = BIT(1) | BIT(2),
};
{ USB_DEVICE_INTERFACE_CLASS(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1012, 0xff) },
{ USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC650) },
{ USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC680) },
+ { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6000)}, /* ZTE AC8700 */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x0023)}, /* ONYX 3G device */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x9000)}, /* SIMCom SIM5218 */
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff93, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff94, 0xff, 0xff, 0xff) },
- /* NOTE: most ZTE CDMA devices should be driven by zte_ev, not option */
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710T, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2718, 0xff, 0xff, 0xff),
.driver_info = (kernel_ulong_t)&zte_mc2718_z_blacklist },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AD3812, 0xff, 0xff, 0xff),
+ .driver_info = (kernel_ulong_t)&zte_ad3812_z_blacklist },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2716, 0xff, 0xff, 0xff),
+ .driver_info = (kernel_ulong_t)&zte_mc2716_z_blacklist },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x01) },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x05) },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x86, 0x10) },
- { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) },
{ USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) },
{ USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) },
{ USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e01, 0xff, 0xff, 0xff) }, /* D-Link DWM-152/C1 */
{ USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e02, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/C1 */
{ USB_DEVICE(INOVIA_VENDOR_ID, INOVIA_SEW858) },
+ { USB_DEVICE(VIATELECOM_VENDOR_ID, VIATELECOM_PRODUCT_CDS7) },
{ } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, option_ids);
dev_dbg(dev, "%s: type %x req %x\n", __func__,
req_pkt->bRequestType, req_pkt->bRequest);
}
+ } else if (status == -ENOENT || status == -ESHUTDOWN) {
+ dev_dbg(dev, "%s: urb stopped: %d\n", __func__, status);
} else
dev_err(dev, "%s: error %d\n", __func__, status);
{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_GPRS) },
{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_HCR331) },
{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_MOTOROLA) },
+ { USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_ZTEK) },
{ USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID) },
{ USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID_RSAQ5) },
{ USB_DEVICE(ATEN_VENDOR_ID, ATEN_PRODUCT_ID) },
#define PL2303_PRODUCT_ID_GPRS 0x0609
#define PL2303_PRODUCT_ID_HCR331 0x331a
#define PL2303_PRODUCT_ID_MOTOROLA 0x0307
+#define PL2303_PRODUCT_ID_ZTEK 0xe1f1
#define ATEN_VENDOR_ID 0x0557
#define ATEN_VENDOR_ID2 0x0547
if (usb_endpoint_is_bulk_in(endpoint)) {
/* we found a bulk in endpoint */
dev_dbg(ddev, "found bulk in on endpoint %d\n", i);
- bulk_in_endpoint[num_bulk_in] = endpoint;
- ++num_bulk_in;
+ if (num_bulk_in < MAX_NUM_PORTS) {
+ bulk_in_endpoint[num_bulk_in] = endpoint;
+ ++num_bulk_in;
+ }
}
if (usb_endpoint_is_bulk_out(endpoint)) {
/* we found a bulk out endpoint */
dev_dbg(ddev, "found bulk out on endpoint %d\n", i);
- bulk_out_endpoint[num_bulk_out] = endpoint;
- ++num_bulk_out;
+ if (num_bulk_out < MAX_NUM_PORTS) {
+ bulk_out_endpoint[num_bulk_out] = endpoint;
+ ++num_bulk_out;
+ }
}
if (usb_endpoint_is_int_in(endpoint)) {
/* we found a interrupt in endpoint */
dev_dbg(ddev, "found interrupt in on endpoint %d\n", i);
- interrupt_in_endpoint[num_interrupt_in] = endpoint;
- ++num_interrupt_in;
+ if (num_interrupt_in < MAX_NUM_PORTS) {
+ interrupt_in_endpoint[num_interrupt_in] =
+ endpoint;
+ ++num_interrupt_in;
+ }
}
if (usb_endpoint_is_int_out(endpoint)) {
/* we found an interrupt out endpoint */
dev_dbg(ddev, "found interrupt out on endpoint %d\n", i);
- interrupt_out_endpoint[num_interrupt_out] = endpoint;
- ++num_interrupt_out;
+ if (num_interrupt_out < MAX_NUM_PORTS) {
+ interrupt_out_endpoint[num_interrupt_out] =
+ endpoint;
+ ++num_interrupt_out;
+ }
}
}
if (usb_endpoint_is_int_in(endpoint)) {
/* we found a interrupt in endpoint */
dev_dbg(ddev, "found interrupt in for Prolific device on separate interface\n");
- interrupt_in_endpoint[num_interrupt_in] = endpoint;
- ++num_interrupt_in;
+ if (num_interrupt_in < MAX_NUM_PORTS) {
+ interrupt_in_endpoint[num_interrupt_in] = endpoint;
+ ++num_interrupt_in;
+ }
}
}
}
num_ports = type->num_ports;
}
+ if (num_ports > MAX_NUM_PORTS) {
+ dev_warn(ddev, "too many ports requested: %d\n", num_ports);
+ num_ports = MAX_NUM_PORTS;
+ }
+
serial->num_ports = num_ports;
serial->num_bulk_in = num_bulk_in;
serial->num_bulk_out = num_bulk_out;
dev_dbg(&urb->dev->dev, "%s - command_info is NULL, exiting.\n", __func__);
return;
}
+ if (!urb->actual_length) {
+ dev_dbg(&urb->dev->dev, "%s - empty response, exiting.\n", __func__);
+ return;
+ }
if (status) {
dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n", __func__, status);
if (status != -ENOENT)
/* These are unsolicited reports from the firmware, hence no
waiting command to wakeup */
dev_dbg(&urb->dev->dev, "%s - event received\n", __func__);
- } else if (data[0] == WHITEHEAT_GET_DTR_RTS) {
+ } else if ((data[0] == WHITEHEAT_GET_DTR_RTS) &&
+ (urb->actual_length - 1 <= sizeof(command_info->result_buffer))) {
memcpy(command_info->result_buffer, &data[1],
urb->actual_length - 1);
command_info->command_finished = WHITEHEAT_CMD_COMPLETE;
}
static const struct usb_device_id id_table[] = {
- /* AC8710, AC8710T */
- { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffff, 0xff, 0xff, 0xff) },
- /* AC8700 */
- { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xfffe, 0xff, 0xff, 0xff) },
/* MG880 */
{ USB_DEVICE(0x19d2, 0xfffd) },
- { USB_DEVICE(0x19d2, 0xfffc) },
- { USB_DEVICE(0x19d2, 0xfffb) },
- /* AC8710_V3 */
- { USB_DEVICE(0x19d2, 0xfff6) },
- { USB_DEVICE(0x19d2, 0xfff7) },
- { USB_DEVICE(0x19d2, 0xfff8) },
- { USB_DEVICE(0x19d2, 0xfff9) },
- { USB_DEVICE(0x19d2, 0xffee) },
- /* AC2716, MC2716 */
- { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffed, 0xff, 0xff, 0xff) },
- /* AD3812 */
- { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffeb, 0xff, 0xff, 0xff) },
- { USB_DEVICE(0x19d2, 0xffec) },
- { USB_DEVICE(0x05C6, 0x3197) },
- { USB_DEVICE(0x05C6, 0x6000) },
- { USB_DEVICE(0x05C6, 0x9008) },
{ },
};
MODULE_DEVICE_TABLE(usb, id_table);
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
US_FL_FIX_CAPACITY ),
+UNUSUAL_DEV( 0x06ca, 0x2003, 0x0100, 0x0100,
+ "Newer Technology",
+ "uSCSI",
+ USB_SC_DEVICE, USB_PR_DEVICE, usb_stor_euscsi_init,
+ US_FL_SCM_MULT_TARG ),
+
/* Reported by Adrian Pilchowiec <adi1981@epf.pl> */
UNUSUAL_DEV( 0x071b, 0x3203, 0x0000, 0x0000,
"RockChip",
#include "stub.h"
/*
- * Define device IDs here if you want to explicitly limit exportable devices.
- * In most cases, wildcard matching will be okay because driver binding can be
- * changed dynamically by a userland program.
- */
-static struct usb_device_id stub_table[] = {
-#if 0
- /* just an example */
- { USB_DEVICE(0x05ac, 0x0301) }, /* Mac 1 button mouse */
- { USB_DEVICE(0x0430, 0x0009) }, /* Plat Home Keyboard */
- { USB_DEVICE(0x059b, 0x0001) }, /* Iomega USB Zip 100 */
- { USB_DEVICE(0x04b3, 0x4427) }, /* IBM USB CD-ROM */
- { USB_DEVICE(0x05a9, 0xa511) }, /* LifeView USB cam */
- { USB_DEVICE(0x55aa, 0x0201) }, /* Imation card reader */
- { USB_DEVICE(0x046d, 0x0870) }, /* Qcam Express(QV-30) */
- { USB_DEVICE(0x04bb, 0x0101) }, /* IO-DATA HD 120GB */
- { USB_DEVICE(0x04bb, 0x0904) }, /* IO-DATA USB-ET/TX */
- { USB_DEVICE(0x04bb, 0x0201) }, /* IO-DATA USB-ET/TX */
- { USB_DEVICE(0x08bb, 0x2702) }, /* ONKYO USB Speaker */
- { USB_DEVICE(0x046d, 0x08b2) }, /* Logicool Qcam 4000 Pro */
-#endif
- /* magic for wild card */
- { .driver_info = 1 },
- { 0, } /* Terminating entry */
-};
-MODULE_DEVICE_TABLE(usb, stub_table);
-
-/*
* usbip_status shows the status of usbip-host as long as this driver is bound
* to the target device.
*/
#include <linux/types.h>
#include <linux/usb.h>
#include <linux/wait.h>
-#include "uapi/usbip.h"
+#include <uapi/linux/usbip.h>
#define USBIP_VERSION "1.0.0"
dev = &wa->usb_iface->dev;
--(wa->active_buf_in_urbs);
active_buf_in_urbs = wa->active_buf_in_urbs;
+ rpipe = xfer->ep->hcpriv;
if (usb_pipeisoc(xfer->urb->pipe)) {
struct usb_iso_packet_descriptor *iso_frame_desc =
resubmit_dti = (isoc_data_frame_count ==
urb_frame_count);
} else if (active_buf_in_urbs == 0) {
- rpipe = xfer->ep->hcpriv;
dev_dbg(dev,
"xfer %p 0x%08X#%u: data in done (%zu bytes)\n",
xfer, wa_xfer_id(xfer), seg->index,
*/
resubmit_dti = wa->dti_state != WA_DTI_TRANSFER_RESULT_PENDING;
spin_lock_irqsave(&xfer->lock, flags);
- rpipe = xfer->ep->hcpriv;
if (printk_ratelimit())
dev_err(dev, "xfer %p 0x%08X#%u: data in error %d\n",
xfer, wa_xfer_id(xfer), seg->index,
data->max_brightness--;
}
+ data->enable_gpio = -EINVAL;
return 0;
}
#include <linux/list.h>
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
+#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/hardirq.h>
#include <linux/dma-mapping.h>
{
struct device_node *endpoint;
int err;
+ unsigned int bpp;
u32 max_bandwidth;
u32 tft_r0b0g0[3];
err = of_property_read_u32(fb->dev->dev.of_node, "max-memory-bandwidth",
&max_bandwidth);
- if (!err)
- fb->panel->bpp = 8 * max_bandwidth / (fb->panel->mode.xres *
- fb->panel->mode.yres * fb->panel->mode.refresh);
- else
- fb->panel->bpp = 32;
+ if (!err) {
+ /*
+ * max_bandwidth is in bytes per second and pixclock in
+ * pico-seconds, so the maximum allowed bits per pixel is
+ * 8 * max_bandwidth / (PICOS2KHZ(pixclock) * 1000)
+ * Rearrange this calculation to avoid overflow and then ensure
+ * result is a valid format.
+ */
+ bpp = max_bandwidth / (1000 / 8)
+ / PICOS2KHZ(fb->panel->mode.pixclock);
+ bpp = rounddown_pow_of_two(bpp);
+ if (bpp > 32)
+ bpp = 32;
+ } else
+ bpp = 32;
+ fb->panel->bpp = bpp;
#ifdef CONFIG_CPU_BIG_ENDIAN
fb->panel->cntl |= CNTL_BEBO;
timings = of_get_display_timings(display_np);
if (!timings) {
dev_err(dev, "failed to get display timings\n");
+ ret = -EINVAL;
goto put_display_node;
}
timings_np = of_find_node_by_name(display_np, "display-timings");
if (!timings_np) {
dev_err(dev, "failed to find display-timings node\n");
+ ret = -ENODEV;
goto put_display_node;
}
{ 0xa8, 0x00 }
};
-static void __init chips_hw_init(void)
+static void chips_hw_init(void)
{
int i;
{
u32 reg;
- reg = lcdc_read(LCD_RASTER_TIMING_0_REG) & 0xf;
+ reg = lcdc_read(LCD_RASTER_TIMING_0_REG) & 0x3ff;
reg |= (((back_porch-1) & 0xff) << 24)
| (((front_porch-1) & 0xff) << 16)
| (((pulse_width-1) & 0x3f) << 10);
if (native_mode)
of_node_put(native_mode);
display_timings_release(disp);
+ disp = NULL;
entryfail:
kfree(disp);
dispfail:
for (i = 0; i < table->nr; ++i) {
struct kioctx *ctx = table->table[i];
+ struct completion requests_done =
+ COMPLETION_INITIALIZER_ONSTACK(requests_done);
if (!ctx)
continue;
* that it needs to unmap the area, just set it to 0.
*/
ctx->mmap_size = 0;
- kill_ioctx(mm, ctx, NULL);
+ kill_ioctx(mm, ctx, &requests_done);
+
+ /* Wait until all IO for the context are done. */
+ wait_for_completion(&requests_done);
}
RCU_INIT_POINTER(mm->ioctx_table, NULL);
tail = ring->tail;
kunmap_atomic(ring);
+ /*
+ * Ensure that once we've read the current tail pointer, that
+ * we also see the events that were stored up to the tail.
+ */
+ smp_rmb();
+
pr_debug("h%u t%u m%u\n", head, tail, ctx->nr_events);
if (head == tail)
#include <linux/list.h>
#include <linux/spinlock.h>
#include <linux/freezer.h>
-#include <linux/workqueue.h>
#include "async-thread.h"
#include "ctree.h"
struct __btrfs_workqueue *high;
};
-static inline struct __btrfs_workqueue
-*__btrfs_alloc_workqueue(const char *name, int flags, int max_active,
+static void normal_work_helper(struct btrfs_work *work);
+
+#define BTRFS_WORK_HELPER(name) \
+void btrfs_##name(struct work_struct *arg) \
+{ \
+ struct btrfs_work *work = container_of(arg, struct btrfs_work, \
+ normal_work); \
+ normal_work_helper(work); \
+}
+
+BTRFS_WORK_HELPER(worker_helper);
+BTRFS_WORK_HELPER(delalloc_helper);
+BTRFS_WORK_HELPER(flush_delalloc_helper);
+BTRFS_WORK_HELPER(cache_helper);
+BTRFS_WORK_HELPER(submit_helper);
+BTRFS_WORK_HELPER(fixup_helper);
+BTRFS_WORK_HELPER(endio_helper);
+BTRFS_WORK_HELPER(endio_meta_helper);
+BTRFS_WORK_HELPER(endio_meta_write_helper);
+BTRFS_WORK_HELPER(endio_raid56_helper);
+BTRFS_WORK_HELPER(rmw_helper);
+BTRFS_WORK_HELPER(endio_write_helper);
+BTRFS_WORK_HELPER(freespace_write_helper);
+BTRFS_WORK_HELPER(delayed_meta_helper);
+BTRFS_WORK_HELPER(readahead_helper);
+BTRFS_WORK_HELPER(qgroup_rescan_helper);
+BTRFS_WORK_HELPER(extent_refs_helper);
+BTRFS_WORK_HELPER(scrub_helper);
+BTRFS_WORK_HELPER(scrubwrc_helper);
+BTRFS_WORK_HELPER(scrubnc_helper);
+
+static struct __btrfs_workqueue *
+__btrfs_alloc_workqueue(const char *name, int flags, int max_active,
int thresh)
{
struct __btrfs_workqueue *ret = kzalloc(sizeof(*ret), GFP_NOFS);
spin_unlock_irqrestore(lock, flags);
}
-static void normal_work_helper(struct work_struct *arg)
+static void normal_work_helper(struct btrfs_work *work)
{
- struct btrfs_work *work;
struct __btrfs_workqueue *wq;
int need_order = 0;
- work = container_of(arg, struct btrfs_work, normal_work);
/*
* We should not touch things inside work in the following cases:
* 1) after work->func() if it has no ordered_free
trace_btrfs_all_work_done(work);
}
-void btrfs_init_work(struct btrfs_work *work,
+void btrfs_init_work(struct btrfs_work *work, btrfs_work_func_t uniq_func,
btrfs_func_t func,
btrfs_func_t ordered_func,
btrfs_func_t ordered_free)
work->func = func;
work->ordered_func = ordered_func;
work->ordered_free = ordered_free;
- INIT_WORK(&work->normal_work, normal_work_helper);
+ INIT_WORK(&work->normal_work, uniq_func);
INIT_LIST_HEAD(&work->ordered_list);
work->flags = 0;
}
#ifndef __BTRFS_ASYNC_THREAD_
#define __BTRFS_ASYNC_THREAD_
+#include <linux/workqueue.h>
struct btrfs_workqueue;
/* Internal use only */
struct __btrfs_workqueue;
struct btrfs_work;
typedef void (*btrfs_func_t)(struct btrfs_work *arg);
+typedef void (*btrfs_work_func_t)(struct work_struct *arg);
struct btrfs_work {
btrfs_func_t func;
unsigned long flags;
};
+#define BTRFS_WORK_HELPER_PROTO(name) \
+void btrfs_##name(struct work_struct *arg)
+
+BTRFS_WORK_HELPER_PROTO(worker_helper);
+BTRFS_WORK_HELPER_PROTO(delalloc_helper);
+BTRFS_WORK_HELPER_PROTO(flush_delalloc_helper);
+BTRFS_WORK_HELPER_PROTO(cache_helper);
+BTRFS_WORK_HELPER_PROTO(submit_helper);
+BTRFS_WORK_HELPER_PROTO(fixup_helper);
+BTRFS_WORK_HELPER_PROTO(endio_helper);
+BTRFS_WORK_HELPER_PROTO(endio_meta_helper);
+BTRFS_WORK_HELPER_PROTO(endio_meta_write_helper);
+BTRFS_WORK_HELPER_PROTO(endio_raid56_helper);
+BTRFS_WORK_HELPER_PROTO(rmw_helper);
+BTRFS_WORK_HELPER_PROTO(endio_write_helper);
+BTRFS_WORK_HELPER_PROTO(freespace_write_helper);
+BTRFS_WORK_HELPER_PROTO(delayed_meta_helper);
+BTRFS_WORK_HELPER_PROTO(readahead_helper);
+BTRFS_WORK_HELPER_PROTO(qgroup_rescan_helper);
+BTRFS_WORK_HELPER_PROTO(extent_refs_helper);
+BTRFS_WORK_HELPER_PROTO(scrub_helper);
+BTRFS_WORK_HELPER_PROTO(scrubwrc_helper);
+BTRFS_WORK_HELPER_PROTO(scrubnc_helper);
+
struct btrfs_workqueue *btrfs_alloc_workqueue(const char *name,
int flags,
int max_active,
int thresh);
-void btrfs_init_work(struct btrfs_work *work,
+void btrfs_init_work(struct btrfs_work *work, btrfs_work_func_t helper,
btrfs_func_t func,
btrfs_func_t ordered_func,
btrfs_func_t ordered_free);
return -ENOMEM;
async_work->delayed_root = delayed_root;
- btrfs_init_work(&async_work->work, btrfs_async_run_delayed_root,
- NULL, NULL);
+ btrfs_init_work(&async_work->work, btrfs_delayed_meta_helper,
+ btrfs_async_run_delayed_root, NULL, NULL);
async_work->nr = nr;
btrfs_queue_work(root->fs_info->delayed_workers, &async_work->work);
#include "btrfs_inode.h"
#include "volumes.h"
#include "print-tree.h"
-#include "async-thread.h"
#include "locking.h"
#include "tree-log.h"
#include "free-space-cache.h"
{
struct end_io_wq *end_io_wq = bio->bi_private;
struct btrfs_fs_info *fs_info;
+ struct btrfs_workqueue *wq;
+ btrfs_work_func_t func;
fs_info = end_io_wq->info;
end_io_wq->error = err;
- btrfs_init_work(&end_io_wq->work, end_workqueue_fn, NULL, NULL);
if (bio->bi_rw & REQ_WRITE) {
- if (end_io_wq->metadata == BTRFS_WQ_ENDIO_METADATA)
- btrfs_queue_work(fs_info->endio_meta_write_workers,
- &end_io_wq->work);
- else if (end_io_wq->metadata == BTRFS_WQ_ENDIO_FREE_SPACE)
- btrfs_queue_work(fs_info->endio_freespace_worker,
- &end_io_wq->work);
- else if (end_io_wq->metadata == BTRFS_WQ_ENDIO_RAID56)
- btrfs_queue_work(fs_info->endio_raid56_workers,
- &end_io_wq->work);
- else
- btrfs_queue_work(fs_info->endio_write_workers,
- &end_io_wq->work);
+ if (end_io_wq->metadata == BTRFS_WQ_ENDIO_METADATA) {
+ wq = fs_info->endio_meta_write_workers;
+ func = btrfs_endio_meta_write_helper;
+ } else if (end_io_wq->metadata == BTRFS_WQ_ENDIO_FREE_SPACE) {
+ wq = fs_info->endio_freespace_worker;
+ func = btrfs_freespace_write_helper;
+ } else if (end_io_wq->metadata == BTRFS_WQ_ENDIO_RAID56) {
+ wq = fs_info->endio_raid56_workers;
+ func = btrfs_endio_raid56_helper;
+ } else {
+ wq = fs_info->endio_write_workers;
+ func = btrfs_endio_write_helper;
+ }
} else {
- if (end_io_wq->metadata == BTRFS_WQ_ENDIO_RAID56)
- btrfs_queue_work(fs_info->endio_raid56_workers,
- &end_io_wq->work);
- else if (end_io_wq->metadata)
- btrfs_queue_work(fs_info->endio_meta_workers,
- &end_io_wq->work);
- else
- btrfs_queue_work(fs_info->endio_workers,
- &end_io_wq->work);
+ if (end_io_wq->metadata == BTRFS_WQ_ENDIO_RAID56) {
+ wq = fs_info->endio_raid56_workers;
+ func = btrfs_endio_raid56_helper;
+ } else if (end_io_wq->metadata) {
+ wq = fs_info->endio_meta_workers;
+ func = btrfs_endio_meta_helper;
+ } else {
+ wq = fs_info->endio_workers;
+ func = btrfs_endio_helper;
+ }
}
+
+ btrfs_init_work(&end_io_wq->work, func, end_workqueue_fn, NULL, NULL);
+ btrfs_queue_work(wq, &end_io_wq->work);
}
/*
async->submit_bio_start = submit_bio_start;
async->submit_bio_done = submit_bio_done;
- btrfs_init_work(&async->work, run_one_async_start,
+ btrfs_init_work(&async->work, btrfs_worker_helper, run_one_async_start,
run_one_async_done, run_one_async_free);
async->bio_flags = bio_flags;
btrfs_set_stack_device_generation(dev_item, 0);
btrfs_set_stack_device_type(dev_item, dev->type);
btrfs_set_stack_device_id(dev_item, dev->devid);
- btrfs_set_stack_device_total_bytes(dev_item, dev->total_bytes);
+ btrfs_set_stack_device_total_bytes(dev_item,
+ dev->disk_total_bytes);
btrfs_set_stack_device_bytes_used(dev_item, dev->bytes_used);
btrfs_set_stack_device_io_align(dev_item, dev->io_align);
btrfs_set_stack_device_io_width(dev_item, dev->io_width);
caching_ctl->block_group = cache;
caching_ctl->progress = cache->key.objectid;
atomic_set(&caching_ctl->count, 1);
- btrfs_init_work(&caching_ctl->work, caching_thread, NULL, NULL);
+ btrfs_init_work(&caching_ctl->work, btrfs_cache_helper,
+ caching_thread, NULL, NULL);
spin_lock(&cache->lock);
/*
async->sync = 0;
init_completion(&async->wait);
- btrfs_init_work(&async->work, delayed_ref_async_start,
- NULL, NULL);
+ btrfs_init_work(&async->work, btrfs_extent_refs_helper,
+ delayed_ref_async_start, NULL, NULL);
btrfs_queue_work(root->fs_info->extent_workers, &async->work);
*/
static u64 btrfs_reduce_alloc_profile(struct btrfs_root *root, u64 flags)
{
- /*
- * we add in the count of missing devices because we want
- * to make sure that any RAID levels on a degraded FS
- * continue to be honored.
- */
- u64 num_devices = root->fs_info->fs_devices->rw_devices +
- root->fs_info->fs_devices->missing_devices;
+ u64 num_devices = root->fs_info->fs_devices->rw_devices;
u64 target;
u64 tmp;
if (stripped)
return extended_to_chunk(stripped);
- /*
- * we add in the count of missing devices because we want
- * to make sure that any RAID levels on a degraded FS
- * continue to be honored.
- */
- num_devices = root->fs_info->fs_devices->rw_devices +
- root->fs_info->fs_devices->missing_devices;
+ num_devices = root->fs_info->fs_devices->rw_devices;
stripped = BTRFS_BLOCK_GROUP_RAID0 |
BTRFS_BLOCK_GROUP_RAID5 | BTRFS_BLOCK_GROUP_RAID6 |
test_bit(BIO_UPTODATE, &bio->bi_flags);
if (err)
uptodate = 0;
+ offset += len;
continue;
}
}
return -ENOMEM;
path->leave_spinning = 1;
- start = ALIGN(start, BTRFS_I(inode)->root->sectorsize);
- len = ALIGN(len, BTRFS_I(inode)->root->sectorsize);
+ start = round_down(start, BTRFS_I(inode)->root->sectorsize);
+ len = round_up(max, BTRFS_I(inode)->root->sectorsize) - start;
/*
* lookup the last file extent. We're not using i_size here
{
if (filp->private_data)
btrfs_ioctl_trans_end(filp);
- filemap_flush(inode->i_mapping);
+ /*
+ * ordered_data_close is set by settattr when we are about to truncate
+ * a file from a non-zero size to a zero size. This tries to
+ * flush down new bytes that may have been written if the
+ * application were using truncate to replace a file in place.
+ */
+ if (test_and_clear_bit(BTRFS_INODE_ORDERED_DATA_CLOSE,
+ &BTRFS_I(inode)->runtime_flags))
+ filemap_flush(inode->i_mapping);
return 0;
}
goto out;
}
- if (hole_mergeable(inode, leaf, path->slots[0]+1, offset, end)) {
+ if (hole_mergeable(inode, leaf, path->slots[0], offset, end)) {
u64 num_bytes;
- path->slots[0]++;
key.offset = offset;
btrfs_set_item_key_safe(root, path, &key);
fi = btrfs_item_ptr(leaf, path->slots[0],
goto out_only_mutex;
}
- lockstart = round_up(offset , BTRFS_I(inode)->root->sectorsize);
+ lockstart = round_up(offset, BTRFS_I(inode)->root->sectorsize);
lockend = round_down(offset + len,
BTRFS_I(inode)->root->sectorsize) - 1;
same_page = ((offset >> PAGE_CACHE_SHIFT) ==
tail_start + tail_len, 0, 1);
if (ret)
goto out_only_mutex;
- }
+ }
}
}
async_cow->end = cur_end;
INIT_LIST_HEAD(&async_cow->extents);
- btrfs_init_work(&async_cow->work, async_cow_start,
- async_cow_submit, async_cow_free);
+ btrfs_init_work(&async_cow->work,
+ btrfs_delalloc_helper,
+ async_cow_start, async_cow_submit,
+ async_cow_free);
nr_pages = (cur_end - start + PAGE_CACHE_SIZE) >>
PAGE_CACHE_SHIFT;
SetPageChecked(page);
page_cache_get(page);
- btrfs_init_work(&fixup->work, btrfs_writepage_fixup_worker, NULL, NULL);
+ btrfs_init_work(&fixup->work, btrfs_fixup_helper,
+ btrfs_writepage_fixup_worker, NULL, NULL);
fixup->page = page;
btrfs_queue_work(root->fs_info->fixup_workers, &fixup->work);
return -EBUSY;
struct inode *inode = page->mapping->host;
struct btrfs_root *root = BTRFS_I(inode)->root;
struct btrfs_ordered_extent *ordered_extent = NULL;
- struct btrfs_workqueue *workers;
+ struct btrfs_workqueue *wq;
+ btrfs_work_func_t func;
trace_btrfs_writepage_end_io_hook(page, start, end, uptodate);
end - start + 1, uptodate))
return 0;
- btrfs_init_work(&ordered_extent->work, finish_ordered_fn, NULL, NULL);
+ if (btrfs_is_free_space_inode(inode)) {
+ wq = root->fs_info->endio_freespace_worker;
+ func = btrfs_freespace_write_helper;
+ } else {
+ wq = root->fs_info->endio_write_workers;
+ func = btrfs_endio_write_helper;
+ }
- if (btrfs_is_free_space_inode(inode))
- workers = root->fs_info->endio_freespace_worker;
- else
- workers = root->fs_info->endio_write_workers;
- btrfs_queue_work(workers, &ordered_extent->work);
+ btrfs_init_work(&ordered_extent->work, func, finish_ordered_fn, NULL,
+ NULL);
+ btrfs_queue_work(wq, &ordered_extent->work);
return 0;
}
clear_bit(EXTENT_FLAG_LOGGING, &em->flags);
remove_extent_mapping(map_tree, em);
free_extent_map(em);
+ if (need_resched()) {
+ write_unlock(&map_tree->lock);
+ cond_resched();
+ write_lock(&map_tree->lock);
+ }
}
write_unlock(&map_tree->lock);
&cached_state, GFP_NOFS);
free_extent_state(state);
+ cond_resched();
spin_lock(&io_tree->lock);
}
spin_unlock(&io_tree->lock);
iput(inode);
inode = ERR_PTR(ret);
}
+ /*
+ * If orphan cleanup did remove any orphans, it means the tree
+ * was modified and therefore the commit root is not the same as
+ * the current root anymore. This is a problem, because send
+ * uses the commit root and therefore can see inode items that
+ * don't exist in the current root anymore, and for example make
+ * calls to btrfs_iget, which will do tree lookups based on the
+ * current root and not on the commit root. Those lookups will
+ * fail, returning a -ESTALE error, and making send fail with
+ * that error. So make sure a send does not see any orphans we
+ * have just removed, and that it will see the same inodes
+ * regardless of whether a transaction commit happened before
+ * it started (meaning that the commit root will be the same as
+ * the current root) or not.
+ */
+ if (sub_root->node != sub_root->commit_root) {
+ u64 sub_flags = btrfs_root_flags(&sub_root->root_item);
+
+ if (sub_flags & BTRFS_ROOT_SUBVOL_RDONLY) {
+ struct extent_buffer *eb;
+
+ /*
+ * Assert we can't have races between dentry
+ * lookup called through the snapshot creation
+ * ioctl and the VFS.
+ */
+ ASSERT(mutex_is_locked(&dir->i_mutex));
+
+ down_write(&root->fs_info->commit_root_sem);
+ eb = sub_root->commit_root;
+ sub_root->commit_root =
+ btrfs_root_node(sub_root);
+ up_write(&root->fs_info->commit_root_sem);
+ free_extent_buffer(eb);
+ }
+ }
}
return inode;
}
/*
+ * O_TMPFILE, set link count to 0, so that after this point,
+ * we fill in an inode item with the correct link count.
+ */
+ if (!name)
+ set_nlink(inode, 0);
+
+ /*
* we have to initialize this early, so we can reclaim the inode
* number if we fail afterwards in this function.
*/
static int merge_extent_mapping(struct extent_map_tree *em_tree,
struct extent_map *existing,
struct extent_map *em,
- u64 map_start, u64 map_len)
+ u64 map_start)
{
u64 start_diff;
BUG_ON(map_start < em->start || map_start >= extent_map_end(em));
start_diff = map_start - em->start;
em->start = map_start;
- em->len = map_len;
+ em->len = existing->start - em->start;
if (em->block_start < EXTENT_MAP_LAST_BYTE &&
!test_bit(EXTENT_FLAG_COMPRESSED, &em->flags)) {
em->block_start += start_diff;
goto not_found;
if (start + len <= found_key.offset)
goto not_found;
+ if (start > found_key.offset)
+ goto next;
em->start = start;
em->orig_start = start;
em->len = found_key.offset - start;
em->len);
if (existing) {
err = merge_extent_mapping(em_tree, existing,
- em, start,
- root->sectorsize);
+ em, start);
free_extent_map(existing);
if (err) {
free_extent_map(em);
if (!ret)
goto out_test;
- btrfs_init_work(&ordered->work, finish_ordered_fn, NULL, NULL);
+ btrfs_init_work(&ordered->work, btrfs_endio_write_helper,
+ finish_ordered_fn, NULL, NULL);
btrfs_queue_work(root->fs_info->endio_write_workers,
&ordered->work);
out_test:
map_length = orig_bio->bi_iter.bi_size;
ret = btrfs_map_block(root->fs_info, rw, start_sector << 9,
&map_length, NULL, 0);
- if (ret) {
- bio_put(orig_bio);
+ if (ret)
return -EIO;
- }
if (map_length >= orig_bio->bi_iter.bi_size) {
bio = orig_bio;
bio = btrfs_dio_bio_alloc(orig_bio->bi_bdev, start_sector, GFP_NOFS);
if (!bio)
return -ENOMEM;
+
bio->bi_private = dip;
bio->bi_end_io = btrfs_end_dio_bio;
atomic_inc(&dip->pending_bios);
count = iov_iter_count(iter);
if (test_bit(BTRFS_INODE_HAS_ASYNC_EXTENT,
&BTRFS_I(inode)->runtime_flags))
- filemap_fdatawrite_range(inode->i_mapping, offset, count);
+ filemap_fdatawrite_range(inode->i_mapping, offset,
+ offset + count - 1);
if (rw & WRITE) {
/*
work->inode = inode;
work->wait = wait;
work->delay_iput = delay_iput;
- btrfs_init_work(&work->work, btrfs_run_delalloc_work, NULL, NULL);
+ WARN_ON_ONCE(!inode);
+ btrfs_init_work(&work->work, btrfs_flush_delalloc_helper,
+ btrfs_run_delalloc_work, NULL, NULL);
return work;
}
if (ret)
goto out;
+ /*
+ * We set number of links to 0 in btrfs_new_inode(), and here we set
+ * it to 1 because d_tmpfile() will issue a warning if the count is 0,
+ * through:
+ *
+ * d_tmpfile() -> inode_dec_link_count() -> drop_nlink()
+ */
+ set_nlink(inode, 1);
d_tmpfile(dentry, inode);
mark_inode_dirty(inode);
if (ret)
goto fail;
- ret = btrfs_orphan_cleanup(pending_snapshot->snap);
- if (ret)
- goto fail;
-
- /*
- * If orphan cleanup did remove any orphans, it means the tree was
- * modified and therefore the commit root is not the same as the
- * current root anymore. This is a problem, because send uses the
- * commit root and therefore can see inode items that don't exist
- * in the current root anymore, and for example make calls to
- * btrfs_iget, which will do tree lookups based on the current root
- * and not on the commit root. Those lookups will fail, returning a
- * -ESTALE error, and making send fail with that error. So make sure
- * a send does not see any orphans we have just removed, and that it
- * will see the same inodes regardless of whether a transaction
- * commit happened before it started (meaning that the commit root
- * will be the same as the current root) or not.
- */
- if (readonly && pending_snapshot->snap->node !=
- pending_snapshot->snap->commit_root) {
- trans = btrfs_join_transaction(pending_snapshot->snap);
- if (IS_ERR(trans) && PTR_ERR(trans) != -ENOENT) {
- ret = PTR_ERR(trans);
- goto fail;
- }
- if (!IS_ERR(trans)) {
- ret = btrfs_commit_transaction(trans,
- pending_snapshot->snap);
- if (ret)
- goto fail;
- }
- }
-
inode = btrfs_lookup_dentry(dentry->d_parent->d_inode, dentry);
if (IS_ERR(inode)) {
ret = PTR_ERR(inode);
btrfs_mark_buffer_dirty(leaf);
btrfs_release_path(path);
- last_dest_end = new_key.offset + datal;
+ last_dest_end = ALIGN(new_key.offset + datal,
+ root->sectorsize);
ret = clone_finish_inode_update(trans, inode,
last_dest_end,
destoff, olen);
spin_unlock(&root->ordered_extent_lock);
btrfs_init_work(&ordered->flush_work,
+ btrfs_flush_delalloc_helper,
btrfs_run_ordered_extent_work, NULL, NULL);
list_add_tail(&ordered->work_list, &works);
btrfs_queue_work(root->fs_info->flush_workers,
elem.seq, &roots);
btrfs_put_tree_mod_seq(fs_info, &elem);
if (ret < 0)
- return ret;
+ goto out;
if (roots->nnodes != 1)
goto out;
memset(&fs_info->qgroup_rescan_work, 0,
sizeof(fs_info->qgroup_rescan_work));
btrfs_init_work(&fs_info->qgroup_rescan_work,
+ btrfs_qgroup_rescan_helper,
btrfs_qgroup_rescan_worker, NULL, NULL);
if (ret) {
static void async_rmw_stripe(struct btrfs_raid_bio *rbio)
{
- btrfs_init_work(&rbio->work, rmw_work, NULL, NULL);
+ btrfs_init_work(&rbio->work, btrfs_rmw_helper,
+ rmw_work, NULL, NULL);
btrfs_queue_work(rbio->fs_info->rmw_workers,
&rbio->work);
static void async_read_rebuild(struct btrfs_raid_bio *rbio)
{
- btrfs_init_work(&rbio->work, read_rebuild_work, NULL, NULL);
+ btrfs_init_work(&rbio->work, btrfs_rmw_helper,
+ read_rebuild_work, NULL, NULL);
btrfs_queue_work(rbio->fs_info->rmw_workers,
&rbio->work);
plug = container_of(cb, struct btrfs_plug_cb, cb);
if (from_schedule) {
- btrfs_init_work(&plug->work, unplug_work, NULL, NULL);
+ btrfs_init_work(&plug->work, btrfs_rmw_helper,
+ unplug_work, NULL, NULL);
btrfs_queue_work(plug->info->rmw_workers,
&plug->work);
return;
/* FIXME we cannot handle this properly right now */
BUG();
}
- btrfs_init_work(&rmw->work, reada_start_machine_worker, NULL, NULL);
+ btrfs_init_work(&rmw->work, btrfs_readahead_helper,
+ reada_start_machine_worker, NULL, NULL);
rmw->fs_info = fs_info;
btrfs_queue_work(fs_info->readahead_workers, &rmw->work);
sbio->index = i;
sbio->sctx = sctx;
sbio->page_count = 0;
- btrfs_init_work(&sbio->work, scrub_bio_end_io_worker,
- NULL, NULL);
+ btrfs_init_work(&sbio->work, btrfs_scrub_helper,
+ scrub_bio_end_io_worker, NULL, NULL);
if (i != SCRUB_BIOS_PER_SCTX - 1)
sctx->bios[i]->next_free = i + 1;
fixup_nodatasum->root = fs_info->extent_root;
fixup_nodatasum->mirror_num = failed_mirror_index + 1;
scrub_pending_trans_workers_inc(sctx);
- btrfs_init_work(&fixup_nodatasum->work, scrub_fixup_nodatasum,
- NULL, NULL);
+ btrfs_init_work(&fixup_nodatasum->work, btrfs_scrub_helper,
+ scrub_fixup_nodatasum, NULL, NULL);
btrfs_queue_work(fs_info->scrub_workers,
&fixup_nodatasum->work);
goto out;
sbio->err = err;
sbio->bio = bio;
- btrfs_init_work(&sbio->work, scrub_wr_bio_end_io_worker, NULL, NULL);
+ btrfs_init_work(&sbio->work, btrfs_scrubwrc_helper,
+ scrub_wr_bio_end_io_worker, NULL, NULL);
btrfs_queue_work(fs_info->scrub_wr_completion_workers, &sbio->work);
}
struct scrub_ctx *sctx;
int ret;
struct btrfs_device *dev;
+ struct rcu_string *name;
if (btrfs_fs_closing(fs_info))
return -EINVAL;
return -ENODEV;
}
+ if (!is_dev_replace && !readonly && !dev->writeable) {
+ mutex_unlock(&fs_info->fs_devices->device_list_mutex);
+ rcu_read_lock();
+ name = rcu_dereference(dev->name);
+ btrfs_err(fs_info, "scrub: device %s is not writable",
+ name->str);
+ rcu_read_unlock();
+ return -EROFS;
+ }
+
mutex_lock(&fs_info->scrub_lock);
if (!dev->in_fs_metadata || dev->is_tgtdev_for_dev_replace) {
mutex_unlock(&fs_info->scrub_lock);
nocow_ctx->len = len;
nocow_ctx->mirror_num = mirror_num;
nocow_ctx->physical_for_dev_replace = physical_for_dev_replace;
- btrfs_init_work(&nocow_ctx->work, copy_nocow_pages_worker, NULL, NULL);
+ btrfs_init_work(&nocow_ctx->work, btrfs_scrubnc_helper,
+ copy_nocow_pages_worker, NULL, NULL);
INIT_LIST_HEAD(&nocow_ctx->inodes);
btrfs_queue_work(fs_info->scrub_nocow_workers,
&nocow_ctx->work);
if (!fs_info->device_dir_kobj)
return -EINVAL;
- if (one_device) {
+ if (one_device && one_device->bdev) {
disk = one_device->bdev->bd_part;
disk_kobj = &part_to_dev(disk)->kobj;
struct list_head ordered_sums;
int skip_csum = BTRFS_I(inode)->flags & BTRFS_INODE_NODATASUM;
bool has_extents = false;
- bool need_find_last_extent = (*last_extent == 0);
+ bool need_find_last_extent = true;
bool done = false;
INIT_LIST_HEAD(&ordered_sums);
*/
if (ins_keys[i].type == BTRFS_EXTENT_DATA_KEY) {
has_extents = true;
- if (need_find_last_extent &&
- first_key.objectid == (u64)-1)
+ if (first_key.objectid == (u64)-1)
first_key = ins_keys[i];
} else {
need_find_last_extent = false;
if (!has_extents)
return ret;
+ if (need_find_last_extent && *last_extent == first_key.offset) {
+ /*
+ * We don't have any leafs between our current one and the one
+ * we processed before that can have file extent items for our
+ * inode (and have a generation number smaller than our current
+ * transaction id).
+ */
+ need_find_last_extent = false;
+ }
+
/*
* Because we use btrfs_search_forward we could skip leaves that were
* not modified and then assume *last_extent is valid when it really
0, 0);
if (ret)
break;
- *last_extent = offset + len;
+ *last_extent = extent_end;
}
/*
* Need to let the callers know we dropped the path so they should
ret = 1;
device->fs_devices = fs_devices;
} else if (!device->name || strcmp(device->name->str, path)) {
+ /*
+ * When FS is already mounted.
+ * 1. If you are here and if the device->name is NULL that
+ * means this device was missing at time of FS mount.
+ * 2. If you are here and if the device->name is different
+ * from 'path' that means either
+ * a. The same device disappeared and reappeared with
+ * different name. or
+ * b. The missing-disk-which-was-replaced, has
+ * reappeared now.
+ *
+ * We must allow 1 and 2a above. But 2b would be a spurious
+ * and unintentional.
+ *
+ * Further in case of 1 and 2a above, the disk at 'path'
+ * would have missed some transaction when it was away and
+ * in case of 2a the stale bdev has to be updated as well.
+ * 2b must not be allowed at all time.
+ */
+
+ /*
+ * As of now don't allow update to btrfs_fs_device through
+ * the btrfs dev scan cli, after FS has been mounted.
+ */
+ if (fs_devices->opened) {
+ return -EBUSY;
+ } else {
+ /*
+ * That is if the FS is _not_ mounted and if you
+ * are here, that means there is more than one
+ * disk with same uuid and devid.We keep the one
+ * with larger generation number or the last-in if
+ * generation are equal.
+ */
+ if (found_transid < device->generation)
+ return -EEXIST;
+ }
+
name = rcu_string_strdup(path, GFP_NOFS);
if (!name)
return -ENOMEM;
}
}
+ /*
+ * Unmount does not free the btrfs_device struct but would zero
+ * generation along with most of the other members. So just update
+ * it back. We need it to pick the disk with largest generation
+ * (as above).
+ */
+ if (!fs_devices->opened)
+ device->generation = found_transid;
+
if (found_transid > fs_devices->latest_trans) {
fs_devices->latest_devid = devid;
fs_devices->latest_trans = found_transid;
btrfs_set_device_io_align(leaf, dev_item, device->io_align);
btrfs_set_device_io_width(leaf, dev_item, device->io_width);
btrfs_set_device_sector_size(leaf, dev_item, device->sector_size);
- btrfs_set_device_total_bytes(leaf, dev_item, device->total_bytes);
+ btrfs_set_device_total_bytes(leaf, dev_item, device->disk_total_bytes);
btrfs_set_device_bytes_used(leaf, dev_item, device->bytes_used);
btrfs_set_device_group(leaf, dev_item, 0);
btrfs_set_device_seek_speed(leaf, dev_item, 0);
device->fs_devices->total_devices--;
if (device->missing)
- root->fs_info->fs_devices->missing_devices--;
+ device->fs_devices->missing_devices--;
next_device = list_entry(root->fs_info->fs_devices->devices.next,
struct btrfs_device, dev_list);
if (srcdev->bdev) {
fs_info->fs_devices->open_devices--;
- /* zero out the old super */
- btrfs_scratch_superblock(srcdev);
+ /*
+ * zero out the old super if it is not writable
+ * (e.g. seed device)
+ */
+ if (srcdev->writeable)
+ btrfs_scratch_superblock(srcdev);
}
call_rcu(&srcdev->rcu, free_device);
fs_devices->seeding = 0;
fs_devices->num_devices = 0;
fs_devices->open_devices = 0;
+ fs_devices->missing_devices = 0;
+ fs_devices->num_can_discard = 0;
+ fs_devices->rotating = 0;
fs_devices->seed = seed_devices;
generate_random_uuid(fs_devices->fsid);
else
generate_random_uuid(dev->uuid);
- btrfs_init_work(&dev->work, pending_bios_fn, NULL, NULL);
+ btrfs_init_work(&dev->work, btrfs_submit_helper,
+ pending_bios_fn, NULL, NULL);
return dev;
}
/*
* Special error return code only used by dx_probe() and its callers.
*/
-#define ERR_BAD_DX_DIR -75000
+#define ERR_BAD_DX_DIR (-(MAX_ERRNO - 1))
/*
* Timeout and state flag for lazy initialization inode thread.
up_write(&EXT4_I(inode)->i_data_sem);
}
+/* Update i_size, i_disksize. Requires i_mutex to avoid races with truncate */
+static inline int ext4_update_inode_size(struct inode *inode, loff_t newsize)
+{
+ int changed = 0;
+
+ if (newsize > inode->i_size) {
+ i_size_write(inode, newsize);
+ changed = 1;
+ }
+ if (newsize > EXT4_I(inode)->i_disksize) {
+ ext4_update_i_disksize(inode, newsize);
+ changed |= 2;
+ }
+ return changed;
+}
+
struct ext4_group_info {
unsigned long bb_state;
struct rb_root bb_free_root;
}
static int ext4_alloc_file_blocks(struct file *file, ext4_lblk_t offset,
- ext4_lblk_t len, int flags, int mode)
+ ext4_lblk_t len, loff_t new_size,
+ int flags, int mode)
{
struct inode *inode = file_inode(file);
handle_t *handle;
int retries = 0;
struct ext4_map_blocks map;
unsigned int credits;
+ loff_t epos;
map.m_lblk = offset;
+ map.m_len = len;
/*
* Don't normalize the request if it can fit in one extent so
* that it doesn't get unnecessarily split into multiple
credits = ext4_chunk_trans_blocks(inode, len);
retry:
- while (ret >= 0 && ret < len) {
- map.m_lblk = map.m_lblk + ret;
- map.m_len = len = len - ret;
+ while (ret >= 0 && len) {
handle = ext4_journal_start(inode, EXT4_HT_MAP_BLOCKS,
credits);
if (IS_ERR(handle)) {
ret2 = ext4_journal_stop(handle);
break;
}
+ map.m_lblk += ret;
+ map.m_len = len = len - ret;
+ epos = (loff_t)map.m_lblk << inode->i_blkbits;
+ inode->i_ctime = ext4_current_time(inode);
+ if (new_size) {
+ if (epos > new_size)
+ epos = new_size;
+ if (ext4_update_inode_size(inode, epos) & 0x1)
+ inode->i_mtime = inode->i_ctime;
+ } else {
+ if (epos > inode->i_size)
+ ext4_set_inode_flag(inode,
+ EXT4_INODE_EOFBLOCKS);
+ }
+ ext4_mark_inode_dirty(handle, inode);
ret2 = ext4_journal_stop(handle);
if (ret2)
break;
loff_t new_size = 0;
int ret = 0;
int flags;
- int partial;
+ int credits;
+ int partial_begin, partial_end;
loff_t start, end;
ext4_lblk_t lblk;
struct address_space *mapping = inode->i_mapping;
if (start < offset || end > offset + len)
return -EINVAL;
- partial = (offset + len) & ((1 << blkbits) - 1);
+ partial_begin = offset & ((1 << blkbits) - 1);
+ partial_end = (offset + len) & ((1 << blkbits) - 1);
lblk = start >> blkbits;
max_blocks = (end >> blkbits);
* If we have a partial block after EOF we have to allocate
* the entire block.
*/
- if (partial)
+ if (partial_end)
max_blocks += 1;
}
/* Now release the pages and zero block aligned part of pages*/
truncate_pagecache_range(inode, start, end - 1);
+ inode->i_mtime = inode->i_ctime = ext4_current_time(inode);
/* Wait all existing dio workers, newcomers will block on i_mutex */
ext4_inode_block_unlocked_dio(inode);
if (ret)
goto out_dio;
- ret = ext4_alloc_file_blocks(file, lblk, max_blocks, flags,
- mode);
+ ret = ext4_alloc_file_blocks(file, lblk, max_blocks, new_size,
+ flags, mode);
if (ret)
goto out_dio;
}
+ if (!partial_begin && !partial_end)
+ goto out_dio;
- handle = ext4_journal_start(inode, EXT4_HT_MISC, 4);
+ /*
+ * In worst case we have to writeout two nonadjacent unwritten
+ * blocks and update the inode
+ */
+ credits = (2 * ext4_ext_index_trans_blocks(inode, 2)) + 1;
+ if (ext4_should_journal_data(inode))
+ credits += 2;
+ handle = ext4_journal_start(inode, EXT4_HT_MISC, credits);
if (IS_ERR(handle)) {
ret = PTR_ERR(handle);
ext4_std_error(inode->i_sb, ret);
}
inode->i_mtime = inode->i_ctime = ext4_current_time(inode);
-
if (new_size) {
- if (new_size > i_size_read(inode))
- i_size_write(inode, new_size);
- if (new_size > EXT4_I(inode)->i_disksize)
- ext4_update_i_disksize(inode, new_size);
+ ext4_update_inode_size(inode, new_size);
} else {
/*
* Mark that we allocate beyond EOF so the subsequent truncate
if ((offset + len) > i_size_read(inode))
ext4_set_inode_flag(inode, EXT4_INODE_EOFBLOCKS);
}
-
ext4_mark_inode_dirty(handle, inode);
/* Zero out partial block at the edges of the range */
long ext4_fallocate(struct file *file, int mode, loff_t offset, loff_t len)
{
struct inode *inode = file_inode(file);
- handle_t *handle;
loff_t new_size = 0;
unsigned int max_blocks;
int ret = 0;
int flags;
ext4_lblk_t lblk;
- struct timespec tv;
unsigned int blkbits = inode->i_blkbits;
/* Return error if mode is not supported */
goto out;
}
- ret = ext4_alloc_file_blocks(file, lblk, max_blocks, flags, mode);
+ ret = ext4_alloc_file_blocks(file, lblk, max_blocks, new_size,
+ flags, mode);
if (ret)
goto out;
- handle = ext4_journal_start(inode, EXT4_HT_INODE, 2);
- if (IS_ERR(handle))
- goto out;
-
- tv = inode->i_ctime = ext4_current_time(inode);
-
- if (new_size) {
- if (new_size > i_size_read(inode)) {
- i_size_write(inode, new_size);
- inode->i_mtime = tv;
- }
- if (new_size > EXT4_I(inode)->i_disksize)
- ext4_update_i_disksize(inode, new_size);
- } else {
- /*
- * Mark that we allocate beyond EOF so the subsequent truncate
- * can proceed even if the new size is the same as i_size.
- */
- if ((offset + len) > i_size_read(inode))
- ext4_set_inode_flag(inode, EXT4_INODE_EOFBLOCKS);
+ if (file->f_flags & O_SYNC && EXT4_SB(inode->i_sb)->s_journal) {
+ ret = jbd2_complete_transaction(EXT4_SB(inode->i_sb)->s_journal,
+ EXT4_I(inode)->i_sync_tid);
}
- ext4_mark_inode_dirty(handle, inode);
- if (file->f_flags & O_SYNC)
- ext4_handle_sync(handle);
-
- ext4_journal_stop(handle);
out:
mutex_unlock(&inode->i_mutex);
trace_ext4_fallocate_exit(inode, offset, max_blocks, ret);
} else
copied = block_write_end(file, mapping, pos,
len, copied, page, fsdata);
-
/*
- * No need to use i_size_read() here, the i_size
- * cannot change under us because we hole i_mutex.
- *
- * But it's important to update i_size while still holding page lock:
+ * it's important to update i_size while still holding page lock:
* page writeout could otherwise come in and zero beyond i_size.
*/
- if (pos + copied > inode->i_size) {
- i_size_write(inode, pos + copied);
- i_size_changed = 1;
- }
-
- if (pos + copied > EXT4_I(inode)->i_disksize) {
- /* We need to mark inode dirty even if
- * new_i_size is less that inode->i_size
- * but greater than i_disksize. (hint delalloc)
- */
- ext4_update_i_disksize(inode, (pos + copied));
- i_size_changed = 1;
- }
+ i_size_changed = ext4_update_inode_size(inode, pos + copied);
unlock_page(page);
page_cache_release(page);
int ret = 0, ret2;
int partial = 0;
unsigned from, to;
- loff_t new_i_size;
+ int size_changed = 0;
trace_ext4_journalled_write_end(inode, pos, len, copied);
from = pos & (PAGE_CACHE_SIZE - 1);
if (!partial)
SetPageUptodate(page);
}
- new_i_size = pos + copied;
- if (new_i_size > inode->i_size)
- i_size_write(inode, pos+copied);
+ size_changed = ext4_update_inode_size(inode, pos + copied);
ext4_set_inode_state(inode, EXT4_STATE_JDATA);
EXT4_I(inode)->i_datasync_tid = handle->h_transaction->t_tid;
- if (new_i_size > EXT4_I(inode)->i_disksize) {
- ext4_update_i_disksize(inode, new_i_size);
+ unlock_page(page);
+ page_cache_release(page);
+
+ if (size_changed) {
ret2 = ext4_mark_inode_dirty(handle, inode);
if (!ret)
ret = ret2;
}
- unlock_page(page);
- page_cache_release(page);
if (pos + len > inode->i_size && ext4_can_truncate(inode))
/* if we have allocated more blocks and copied
* less. We will have blocks allocated outside
struct ext4_map_blocks *map = &mpd->map;
int err;
loff_t disksize;
+ int progress = 0;
mpd->io_submit.io_end->offset =
((loff_t)map->m_lblk) << inode->i_blkbits;
* is non-zero, a commit should free up blocks.
*/
if ((err == -ENOMEM) ||
- (err == -ENOSPC && ext4_count_free_clusters(sb)))
+ (err == -ENOSPC && ext4_count_free_clusters(sb))) {
+ if (progress)
+ goto update_disksize;
return err;
+ }
ext4_msg(sb, KERN_CRIT,
"Delayed block allocation failed for "
"inode %lu at logical offset %llu with"
*give_up_on_write = true;
return err;
}
+ progress = 1;
/*
* Update buffer state, submit mapped pages, and get us new
* extent to map
*/
err = mpage_map_and_submit_buffers(mpd);
if (err < 0)
- return err;
+ goto update_disksize;
} while (map->m_len);
+update_disksize:
/*
* Update on-disk size after IO is submitted. Races with
* truncate are avoided by checking i_size under i_data_sem.
int last = first + count - 1;
struct super_block *sb = e4b->bd_sb;
+ if (WARN_ON(count == 0))
+ return;
BUG_ON(last >= (sb->s_blocksize << 3));
assert_spin_locked(ext4_group_lock_ptr(sb, e4b->bd_group));
/* Don't bother if the block group is corrupt. */
int err;
if (pa == NULL) {
+ if (ac->ac_f_ex.fe_len == 0)
+ return;
err = ext4_mb_load_buddy(ac->ac_sb, ac->ac_f_ex.fe_group, &e4b);
if (err) {
/*
mb_free_blocks(ac->ac_inode, &e4b, ac->ac_f_ex.fe_start,
ac->ac_f_ex.fe_len);
ext4_unlock_group(ac->ac_sb, ac->ac_f_ex.fe_group);
+ ext4_mb_unload_buddy(&e4b);
return;
}
if (pa->pa_type == MB_INODE_PA)
buffer */
int num = 0;
ext4_lblk_t nblocks;
- int i, err;
+ int i, err = 0;
int namelen;
*res_dir = NULL;
* return. Otherwise, fall back to doing a search the
* old fashioned way.
*/
- if (bh || (err != ERR_BAD_DX_DIR))
+ if (err == -ENOENT)
+ return NULL;
+ if (err && err != ERR_BAD_DX_DIR)
+ return ERR_PTR(err);
+ if (bh)
return bh;
dxtrace(printk(KERN_DEBUG "ext4_find_entry: dx failed, "
"falling back\n"));
}
num++;
bh = ext4_getblk(NULL, dir, b++, 0, &err);
+ if (unlikely(err)) {
+ if (ra_max == 0)
+ return ERR_PTR(err);
+ break;
+ }
bh_use[ra_max] = bh;
if (bh)
ll_rw_block(READ | REQ_META | REQ_PRIO,
return ERR_PTR(-ENAMETOOLONG);
bh = ext4_find_entry(dir, &dentry->d_name, &de, NULL);
+ if (IS_ERR(bh))
+ return (struct dentry *) bh;
inode = NULL;
if (bh) {
__u32 ino = le32_to_cpu(de->inode);
struct buffer_head *bh;
bh = ext4_find_entry(child->d_inode, &dotdot, &de, NULL);
+ if (IS_ERR(bh))
+ return (struct dentry *) bh;
if (!bh)
return ERR_PTR(-ENOENT);
ino = le32_to_cpu(de->inode);
retval = -ENOENT;
bh = ext4_find_entry(dir, &dentry->d_name, &de, NULL);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
if (!bh)
goto end_rmdir;
retval = -ENOENT;
bh = ext4_find_entry(dir, &dentry->d_name, &de, NULL);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
if (!bh)
goto end_unlink;
struct ext4_dir_entry_2 *de;
bh = ext4_find_entry(dir, d_name, &de, NULL);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
if (bh) {
retval = ext4_delete_entry(handle, dir, de, bh);
brelse(bh);
return retval;
}
-static void ext4_rename_delete(handle_t *handle, struct ext4_renament *ent)
+static void ext4_rename_delete(handle_t *handle, struct ext4_renament *ent,
+ int force_reread)
{
int retval;
/*
if (le32_to_cpu(ent->de->inode) != ent->inode->i_ino ||
ent->de->name_len != ent->dentry->d_name.len ||
strncmp(ent->de->name, ent->dentry->d_name.name,
- ent->de->name_len)) {
+ ent->de->name_len) ||
+ force_reread) {
retval = ext4_find_delete_entry(handle, ent->dir,
&ent->dentry->d_name);
} else {
.dentry = new_dentry,
.inode = new_dentry->d_inode,
};
+ int force_reread;
int retval;
dquot_initialize(old.dir);
dquot_initialize(new.inode);
old.bh = ext4_find_entry(old.dir, &old.dentry->d_name, &old.de, NULL);
+ if (IS_ERR(old.bh))
+ return PTR_ERR(old.bh);
/*
* Check for inode number is _not_ due to possible IO errors.
* We might rmdir the source, keep it as pwd of some process
new.bh = ext4_find_entry(new.dir, &new.dentry->d_name,
&new.de, &new.inlined);
+ if (IS_ERR(new.bh)) {
+ retval = PTR_ERR(new.bh);
+ goto end_rename;
+ }
if (new.bh) {
if (!new.inode) {
brelse(new.bh);
if (retval)
goto end_rename;
}
+ /*
+ * If we're renaming a file within an inline_data dir and adding or
+ * setting the new dirent causes a conversion from inline_data to
+ * extents/blockmap, we need to force the dirent delete code to
+ * re-read the directory, or else we end up trying to delete a dirent
+ * from what is now the extent tree root (or a block map).
+ */
+ force_reread = (new.dir->i_ino == old.dir->i_ino &&
+ ext4_test_inode_flag(new.dir, EXT4_INODE_INLINE_DATA));
if (!new.bh) {
retval = ext4_add_entry(handle, new.dentry, old.inode);
if (retval)
if (retval)
goto end_rename;
}
+ if (force_reread)
+ force_reread = !ext4_test_inode_flag(new.dir,
+ EXT4_INODE_INLINE_DATA);
/*
* Like most other Unix systems, set the ctime for inodes on a
/*
* ok, that's it
*/
- ext4_rename_delete(handle, &old);
+ ext4_rename_delete(handle, &old, force_reread);
if (new.inode) {
ext4_dec_count(handle, new.inode);
old.bh = ext4_find_entry(old.dir, &old.dentry->d_name,
&old.de, &old.inlined);
+ if (IS_ERR(old.bh))
+ return PTR_ERR(old.bh);
/*
* Check for inode number is _not_ due to possible IO errors.
* We might rmdir the source, keep it as pwd of some process
new.bh = ext4_find_entry(new.dir, &new.dentry->d_name,
&new.de, &new.inlined);
+ if (IS_ERR(new.bh)) {
+ retval = PTR_ERR(new.bh);
+ goto end_rename;
+ }
/* RENAME_EXCHANGE case: old *and* new must both exist */
if (!new.bh || le32_to_cpu(new.de->inode) != new.inode->i_ino)
if (EXT4_HAS_RO_COMPAT_FEATURE(sb,
EXT4_FEATURE_RO_COMPAT_METADATA_CSUM)) {
- /* journal checksum v2 */
+ /* journal checksum v3 */
compat = 0;
- incompat = JBD2_FEATURE_INCOMPAT_CSUM_V2;
+ incompat = JBD2_FEATURE_INCOMPAT_CSUM_V3;
} else {
/* journal checksum v1 */
compat = JBD2_FEATURE_COMPAT_CHECKSUM;
jbd2_journal_clear_features(sbi->s_journal,
JBD2_FEATURE_COMPAT_CHECKSUM, 0,
JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT |
+ JBD2_FEATURE_INCOMPAT_CSUM_V3 |
JBD2_FEATURE_INCOMPAT_CSUM_V2);
}
mounted as f2fs. Each file shows the whole f2fs information.
/sys/kernel/debug/f2fs/status includes:
- - major file system information managed by f2fs currently
+ - major filesystem information managed by f2fs currently
- average SIT information about whole segments
- current memory footprint consumed by f2fs.
bool "F2FS consistency checking feature"
depends on F2FS_FS
help
- Enables BUG_ONs which check the file system consistency in runtime.
+ Enables BUG_ONs which check the filesystem consistency in runtime.
If you want to improve the performance, say N.
goto redirty_out;
if (wbc->for_reclaim)
goto redirty_out;
-
- /* Should not write any meta pages, if any IO error was occurred */
- if (unlikely(is_set_ckpt_flags(F2FS_CKPT(sbi), CP_ERROR_FLAG)))
- goto no_write;
+ if (unlikely(f2fs_cp_error(sbi)))
+ goto redirty_out;
f2fs_wait_on_page_writeback(page, META);
write_meta_page(sbi, page);
-no_write:
dec_page_count(sbi, F2FS_DIRTY_META);
unlock_page(page);
return 0;
return e ? true : false;
}
-static void release_dirty_inode(struct f2fs_sb_info *sbi)
+void release_dirty_inode(struct f2fs_sb_info *sbi)
{
struct ino_entry *e, *tmp;
int i;
struct f2fs_orphan_block *orphan_blk = NULL;
unsigned int nentries = 0;
unsigned short index;
- unsigned short orphan_blocks = (unsigned short)((sbi->n_orphans +
- (F2FS_ORPHANS_PER_BLOCK - 1)) / F2FS_ORPHANS_PER_BLOCK);
+ unsigned short orphan_blocks =
+ (unsigned short)GET_ORPHAN_BLOCKS(sbi->n_orphans);
struct page *page = NULL;
struct ino_entry *orphan = NULL;
/*
* Freeze all the FS-operations for checkpoint.
*/
-static void block_operations(struct f2fs_sb_info *sbi)
+static int block_operations(struct f2fs_sb_info *sbi)
{
struct writeback_control wbc = {
.sync_mode = WB_SYNC_ALL,
.for_reclaim = 0,
};
struct blk_plug plug;
+ int err = 0;
blk_start_plug(&plug);
if (get_pages(sbi, F2FS_DIRTY_DENTS)) {
f2fs_unlock_all(sbi);
sync_dirty_dir_inodes(sbi);
+ if (unlikely(f2fs_cp_error(sbi))) {
+ err = -EIO;
+ goto out;
+ }
goto retry_flush_dents;
}
/*
- * POR: we should ensure that there is no dirty node pages
+ * POR: we should ensure that there are no dirty node pages
* until finishing nat/sit flush.
*/
retry_flush_nodes:
if (get_pages(sbi, F2FS_DIRTY_NODES)) {
up_write(&sbi->node_write);
sync_node_pages(sbi, 0, &wbc);
+ if (unlikely(f2fs_cp_error(sbi))) {
+ f2fs_unlock_all(sbi);
+ err = -EIO;
+ goto out;
+ }
goto retry_flush_nodes;
}
+out:
blk_finish_plug(&plug);
+ return err;
}
static void unblock_operations(struct f2fs_sb_info *sbi)
discard_next_dnode(sbi, NEXT_FREE_BLKADDR(sbi, curseg));
/* Flush all the NAT/SIT pages */
- while (get_pages(sbi, F2FS_DIRTY_META))
+ while (get_pages(sbi, F2FS_DIRTY_META)) {
sync_meta_pages(sbi, META, LONG_MAX);
+ if (unlikely(f2fs_cp_error(sbi)))
+ return;
+ }
next_free_nid(sbi, &last_nid);
ckpt->elapsed_time = cpu_to_le64(get_mtime(sbi));
ckpt->valid_block_count = cpu_to_le64(valid_user_blocks(sbi));
ckpt->free_segment_count = cpu_to_le32(free_segments(sbi));
- for (i = 0; i < 3; i++) {
+ for (i = 0; i < NR_CURSEG_NODE_TYPE; i++) {
ckpt->cur_node_segno[i] =
cpu_to_le32(curseg_segno(sbi, i + CURSEG_HOT_NODE));
ckpt->cur_node_blkoff[i] =
ckpt->alloc_type[i + CURSEG_HOT_NODE] =
curseg_alloc_type(sbi, i + CURSEG_HOT_NODE);
}
- for (i = 0; i < 3; i++) {
+ for (i = 0; i < NR_CURSEG_DATA_TYPE; i++) {
ckpt->cur_data_segno[i] =
cpu_to_le32(curseg_segno(sbi, i + CURSEG_HOT_DATA));
ckpt->cur_data_blkoff[i] =
/* 2 cp + n data seg summary + orphan inode blocks */
data_sum_blocks = npages_for_summary_flush(sbi);
- if (data_sum_blocks < 3)
+ if (data_sum_blocks < NR_CURSEG_DATA_TYPE)
set_ckpt_flags(ckpt, CP_COMPACT_SUM_FLAG);
else
clear_ckpt_flags(ckpt, CP_COMPACT_SUM_FLAG);
- orphan_blocks = (sbi->n_orphans + F2FS_ORPHANS_PER_BLOCK - 1)
- / F2FS_ORPHANS_PER_BLOCK;
+ orphan_blocks = GET_ORPHAN_BLOCKS(sbi->n_orphans);
ckpt->cp_pack_start_sum = cpu_to_le32(1 + cp_payload_blks +
orphan_blocks);
if (is_umount) {
set_ckpt_flags(ckpt, CP_UMOUNT_FLAG);
- ckpt->cp_pack_total_block_count = cpu_to_le32(2 +
+ ckpt->cp_pack_total_block_count = cpu_to_le32(F2FS_CP_PACKS+
cp_payload_blks + data_sum_blocks +
orphan_blocks + NR_CURSEG_NODE_TYPE);
} else {
clear_ckpt_flags(ckpt, CP_UMOUNT_FLAG);
- ckpt->cp_pack_total_block_count = cpu_to_le32(2 +
+ ckpt->cp_pack_total_block_count = cpu_to_le32(F2FS_CP_PACKS +
cp_payload_blks + data_sum_blocks +
orphan_blocks);
}
/* wait for previous submitted node/meta pages writeback */
wait_on_all_pages_writeback(sbi);
+ if (unlikely(f2fs_cp_error(sbi)))
+ return;
+
filemap_fdatawait_range(NODE_MAPPING(sbi), 0, LONG_MAX);
filemap_fdatawait_range(META_MAPPING(sbi), 0, LONG_MAX);
/* Here, we only have one bio having CP pack */
sync_meta_pages(sbi, META_FLUSH, LONG_MAX);
- if (!is_set_ckpt_flags(ckpt, CP_ERROR_FLAG)) {
- clear_prefree_segments(sbi);
- release_dirty_inode(sbi);
- F2FS_RESET_SB_DIRT(sbi);
- }
+ release_dirty_inode(sbi);
+
+ if (unlikely(f2fs_cp_error(sbi)))
+ return;
+
+ clear_prefree_segments(sbi);
+ F2FS_RESET_SB_DIRT(sbi);
}
/*
- * We guarantee that this checkpoint procedure should not fail.
+ * We guarantee that this checkpoint procedure will not fail.
*/
void write_checkpoint(struct f2fs_sb_info *sbi, bool is_umount)
{
trace_f2fs_write_checkpoint(sbi->sb, is_umount, "start block_ops");
mutex_lock(&sbi->cp_mutex);
- block_operations(sbi);
+
+ if (!sbi->s_dirty)
+ goto out;
+ if (unlikely(f2fs_cp_error(sbi)))
+ goto out;
+ if (block_operations(sbi))
+ goto out;
trace_f2fs_write_checkpoint(sbi->sb, is_umount, "finish block_ops");
do_checkpoint(sbi, is_umount);
unblock_operations(sbi);
- mutex_unlock(&sbi->cp_mutex);
-
stat_inc_cp_count(sbi->stat_info);
+out:
+ mutex_unlock(&sbi->cp_mutex);
trace_f2fs_write_checkpoint(sbi->sb, is_umount, "finish checkpoint");
}
* for cp pack we can have max 1020*504 orphan entries
*/
sbi->n_orphans = 0;
- sbi->max_orphans = (sbi->blocks_per_seg - 2 - NR_CURSEG_TYPE)
- * F2FS_ORPHANS_PER_BLOCK;
+ sbi->max_orphans = (sbi->blocks_per_seg - F2FS_CP_PACKS -
+ NR_CURSEG_TYPE) * F2FS_ORPHANS_PER_BLOCK;
}
int __init create_checkpoint_caches(void)
struct page *page = bvec->bv_page;
if (unlikely(err)) {
- SetPageError(page);
+ set_page_dirty(page);
set_bit(AS_EIO, &page->mapping->flags);
f2fs_stop_checkpoint(sbi);
}
allocated = true;
blkaddr = dn.data_blkaddr;
}
- /* Give more consecutive addresses for the read ahead */
+ /* Give more consecutive addresses for the readahead */
if (blkaddr == (bh_result->b_blocknr + ofs)) {
ofs++;
dn.ofs_in_node++;
trace_f2fs_readpage(page, DATA);
- /* If the file has inline data, try to read it directlly */
+ /* If the file has inline data, try to read it directly */
if (f2fs_has_inline_data(inode))
ret = f2fs_read_inline_data(inode, page);
else
/* Dentry blocks are controlled by checkpoint */
if (S_ISDIR(inode->i_mode)) {
+ if (unlikely(f2fs_cp_error(sbi)))
+ goto redirty_out;
err = do_write_data_page(page, &fio);
goto done;
}
+ /* we should bypass data pages to proceed the kworkder jobs */
+ if (unlikely(f2fs_cp_error(sbi))) {
+ SetPageError(page);
+ unlock_page(page);
+ return 0;
+ }
+
if (!wbc->for_reclaim)
need_balance_fs = true;
else if (has_not_enough_free_secs(sbi, 0))
if (to > inode->i_size) {
truncate_pagecache(inode, inode->i_size);
- truncate_blocks(inode, inode->i_size);
+ truncate_blocks(inode, inode->i_size, true);
}
}
f2fs_balance_fs(sbi);
repeat:
- err = f2fs_convert_inline_data(inode, pos + len);
+ err = f2fs_convert_inline_data(inode, pos + len, NULL);
if (err)
goto fail;
struct f2fs_stat_info *si = F2FS_STAT(sbi);
int i;
- /* valid check of the segment numbers */
+ /* validation check of the segment numbers */
si->hit_ext = sbi->read_hit_ext;
si->total_ext = sbi->total_hit_ext;
si->ndirty_node = get_pages(sbi, F2FS_DIRTY_NODES);
si->base_mem += NR_DIRTY_TYPE * f2fs_bitmap_size(TOTAL_SEGS(sbi));
si->base_mem += f2fs_bitmap_size(TOTAL_SECS(sbi));
- /* buld nm */
+ /* build nm */
si->base_mem += sizeof(struct f2fs_nm_info);
si->base_mem += __bitmap_size(sbi, NAT_BITMAP);
/*
* For the most part, it should be a bug when name_len is zero.
- * We stop here for figuring out where the bugs are occurred.
+ * We stop here for figuring out where the bugs has occurred.
*/
f2fs_bug_on(!de->name_len);
error:
/* once the failed inode becomes a bad inode, i_mode is S_IFREG */
truncate_inode_pages(&inode->i_data, 0);
- truncate_blocks(inode, 0);
+ truncate_blocks(inode, 0, false);
remove_dirty_dir_inode(inode);
remove_inode_page(inode);
return ERR_PTR(err);
}
/*
- * It only removes the dentry from the dentry page,corresponding name
+ * It only removes the dentry from the dentry page, corresponding name
* entry in name page does not need to be touched during deletion.
*/
void f2fs_delete_entry(struct f2fs_dir_entry *dentry, struct page *page,
#define f2fs_bug_on(condition) BUG_ON(condition)
#define f2fs_down_write(x, y) down_write_nest_lock(x, y)
#else
-#define f2fs_bug_on(condition)
+#define f2fs_bug_on(condition) WARN_ON(condition)
#define f2fs_down_write(x, y) down_write(x)
#endif
};
/*
- * The below are the page types of bios used in submti_bio().
+ * The below are the page types of bios used in submit_bio().
* The available types are:
* DATA User data pages. It operates as async mode.
* NODE Node pages. It operates as async mode.
struct list_head dir_inode_list; /* dir inode list */
spinlock_t dir_inode_lock; /* for dir inode list lock */
- /* basic file system units */
+ /* basic filesystem units */
unsigned int log_sectors_per_block; /* log2 sectors per block */
unsigned int log_blocksize; /* log2 block size */
unsigned int blocksize; /* block size */
/*
* odd numbered checkpoint should at cp segment 0
- * and even segent must be at cp segment 1
+ * and even segment must be at cp segment 1
*/
if (!(ckpt_version & 1))
start_addr += sbi->blocks_per_seg;
return sb->s_flags & MS_RDONLY;
}
+static inline bool f2fs_cp_error(struct f2fs_sb_info *sbi)
+{
+ return is_set_ckpt_flags(sbi->ckpt, CP_ERROR_FLAG);
+}
+
static inline void f2fs_stop_checkpoint(struct f2fs_sb_info *sbi)
{
set_ckpt_flags(sbi->ckpt, CP_ERROR_FLAG);
*/
int f2fs_sync_file(struct file *, loff_t, loff_t, int);
void truncate_data_blocks(struct dnode_of_data *);
-int truncate_blocks(struct inode *, u64);
+int truncate_blocks(struct inode *, u64, bool);
void f2fs_truncate(struct inode *);
int f2fs_getattr(struct vfsmount *, struct dentry *, struct kstat *);
int f2fs_setattr(struct dentry *, struct iattr *);
bool alloc_nid(struct f2fs_sb_info *, nid_t *);
void alloc_nid_done(struct f2fs_sb_info *, nid_t);
void alloc_nid_failed(struct f2fs_sb_info *, nid_t);
-void recover_node_page(struct f2fs_sb_info *, struct page *,
- struct f2fs_summary *, struct node_info *, block_t);
void recover_inline_xattr(struct inode *, struct page *);
-bool recover_xattr_data(struct inode *, struct page *, block_t);
+void recover_xattr_data(struct inode *, struct page *, block_t);
int recover_inode_page(struct f2fs_sb_info *, struct page *);
int restore_node_summary(struct f2fs_sb_info *, unsigned int,
struct f2fs_summary_block *);
void rewrite_data_page(struct page *, block_t, struct f2fs_io_info *);
void recover_data_page(struct f2fs_sb_info *, struct page *,
struct f2fs_summary *, block_t, block_t);
-void rewrite_node_page(struct f2fs_sb_info *, struct page *,
- struct f2fs_summary *, block_t, block_t);
void allocate_data_block(struct f2fs_sb_info *, struct page *,
block_t, block_t *, struct f2fs_summary *, int);
void f2fs_wait_on_page_writeback(struct page *, enum page_type);
long sync_meta_pages(struct f2fs_sb_info *, enum page_type, long);
void add_dirty_inode(struct f2fs_sb_info *, nid_t, int type);
void remove_dirty_inode(struct f2fs_sb_info *, nid_t, int type);
+void release_dirty_inode(struct f2fs_sb_info *);
bool exist_written_data(struct f2fs_sb_info *, nid_t, int);
int acquire_orphan_inode(struct f2fs_sb_info *);
void release_orphan_inode(struct f2fs_sb_info *);
*/
bool f2fs_may_inline(struct inode *);
int f2fs_read_inline_data(struct inode *, struct page *);
-int f2fs_convert_inline_data(struct inode *, pgoff_t);
+int f2fs_convert_inline_data(struct inode *, pgoff_t, struct page *);
int f2fs_write_inline_data(struct inode *, struct page *, unsigned int);
void truncate_inline_data(struct inode *, u64);
-int recover_inline_data(struct inode *, struct page *);
+bool recover_inline_data(struct inode *, struct page *);
#endif
sb_start_pagefault(inode->i_sb);
+ /* force to convert with normal data indices */
+ err = f2fs_convert_inline_data(inode, MAX_INLINE_DATA + 1, page);
+ if (err)
+ goto out;
+
/* block allocation */
f2fs_lock_op(sbi);
set_new_dnode(&dn, inode, NULL, NULL, 0);
return 1;
}
+static inline bool need_do_checkpoint(struct inode *inode)
+{
+ struct f2fs_sb_info *sbi = F2FS_SB(inode->i_sb);
+ bool need_cp = false;
+
+ if (!S_ISREG(inode->i_mode) || inode->i_nlink != 1)
+ need_cp = true;
+ else if (file_wrong_pino(inode))
+ need_cp = true;
+ else if (!space_for_roll_forward(sbi))
+ need_cp = true;
+ else if (!is_checkpointed_node(sbi, F2FS_I(inode)->i_pino))
+ need_cp = true;
+ else if (F2FS_I(inode)->xattr_ver == cur_cp_version(F2FS_CKPT(sbi)))
+ need_cp = true;
+
+ return need_cp;
+}
+
int f2fs_sync_file(struct file *file, loff_t start, loff_t end, int datasync)
{
struct inode *inode = file->f_mapping->host;
/* guarantee free sections for fsync */
f2fs_balance_fs(sbi);
- down_read(&fi->i_sem);
-
/*
* Both of fdatasync() and fsync() are able to be recovered from
* sudden-power-off.
*/
- if (!S_ISREG(inode->i_mode) || inode->i_nlink != 1)
- need_cp = true;
- else if (file_wrong_pino(inode))
- need_cp = true;
- else if (!space_for_roll_forward(sbi))
- need_cp = true;
- else if (!is_checkpointed_node(sbi, F2FS_I(inode)->i_pino))
- need_cp = true;
- else if (F2FS_I(inode)->xattr_ver == cur_cp_version(F2FS_CKPT(sbi)))
- need_cp = true;
-
+ down_read(&fi->i_sem);
+ need_cp = need_do_checkpoint(inode);
up_read(&fi->i_sem);
if (need_cp) {
if (err && err != -ENOENT) {
goto fail;
} else if (err == -ENOENT) {
- /* direct node is not exist */
+ /* direct node does not exists */
if (whence == SEEK_DATA) {
pgofs = PGOFS_OF_NEXT_DNODE(pgofs,
F2FS_I(inode));
f2fs_put_page(page, 1);
}
-int truncate_blocks(struct inode *inode, u64 from)
+int truncate_blocks(struct inode *inode, u64 from, bool lock)
{
struct f2fs_sb_info *sbi = F2FS_SB(inode->i_sb);
unsigned int blocksize = inode->i_sb->s_blocksize;
free_from = (pgoff_t)
((from + blocksize - 1) >> (sbi->log_blocksize));
- f2fs_lock_op(sbi);
+ if (lock)
+ f2fs_lock_op(sbi);
set_new_dnode(&dn, inode, NULL, NULL, 0);
err = get_dnode_of_data(&dn, free_from, LOOKUP_NODE);
if (err) {
if (err == -ENOENT)
goto free_next;
- f2fs_unlock_op(sbi);
+ if (lock)
+ f2fs_unlock_op(sbi);
trace_f2fs_truncate_blocks_exit(inode, err);
return err;
}
f2fs_put_dnode(&dn);
free_next:
err = truncate_inode_blocks(inode, free_from);
- f2fs_unlock_op(sbi);
+ if (lock)
+ f2fs_unlock_op(sbi);
done:
/* lastly zero out the first data page */
truncate_partial_data_page(inode, from);
trace_f2fs_truncate(inode);
- if (!truncate_blocks(inode, i_size_read(inode))) {
+ if (!truncate_blocks(inode, i_size_read(inode), true)) {
inode->i_mtime = inode->i_ctime = CURRENT_TIME;
mark_inode_dirty(inode);
}
if ((attr->ia_valid & ATTR_SIZE) &&
attr->ia_size != i_size_read(inode)) {
- err = f2fs_convert_inline_data(inode, attr->ia_size);
+ err = f2fs_convert_inline_data(inode, attr->ia_size, NULL);
if (err)
return err;
loff_t off_start, off_end;
int ret = 0;
- ret = f2fs_convert_inline_data(inode, MAX_INLINE_DATA + 1);
+ ret = f2fs_convert_inline_data(inode, MAX_INLINE_DATA + 1, NULL);
if (ret)
return ret;
if (ret)
return ret;
- ret = f2fs_convert_inline_data(inode, offset + len);
+ ret = f2fs_convert_inline_data(inode, offset + len, NULL);
if (ret)
return ret;
* 3. IO subsystem is idle by checking the # of requests in
* bdev's request list.
*
- * Note) We have to avoid triggering GCs too much frequently.
+ * Note) We have to avoid triggering GCs frequently.
* Because it is possible that some segments can be
* invalidated soon after by user update or deletion.
* So, I'd like to wait some time to collect dirty segments.
u = (vblocks * 100) >> sbi->log_blocks_per_seg;
- /* Handle if the system time is changed by user */
+ /* Handle if the system time has changed by the user */
if (mtime < sit_i->min_mtime)
sit_i->min_mtime = mtime;
if (mtime > sit_i->max_mtime)
if (phase == 2) {
inode = f2fs_iget(sb, dni.ino);
- if (IS_ERR(inode))
+ if (IS_ERR(inode) || is_bad_inode(inode))
continue;
start_bidx = start_bidx_of_node(nofs, F2FS_I(inode));
gc_more:
if (unlikely(!(sbi->sb->s_flags & MS_ACTIVE)))
goto stop;
- if (unlikely(is_set_ckpt_flags(F2FS_CKPT(sbi), CP_ERROR_FLAG)))
+ if (unlikely(f2fs_cp_error(sbi)))
goto stop;
if (gc_type == BG_GC && has_not_enough_free_secs(sbi, nfree)) {
block_t invalid_user_blocks = sbi->user_block_count -
written_block_count(sbi);
/*
- * Background GC is triggered with the following condition.
+ * Background GC is triggered with the following conditions.
* 1. There are a number of invalid blocks.
* 2. There is not enough free space.
*/
buf[1] += b1;
}
-static void str2hashbuf(const char *msg, size_t len, unsigned int *buf, int num)
+static void str2hashbuf(const unsigned char *msg, size_t len,
+ unsigned int *buf, int num)
{
unsigned pad, val;
int i;
{
__u32 hash;
f2fs_hash_t f2fs_hash;
- const char *p;
+ const unsigned char *p;
__u32 in[8], buf[4];
- const char *name = name_info->name;
+ const unsigned char *name = name_info->name;
size_t len = name_info->len;
if ((len <= 2) && (name[0] == '.') &&
static int __f2fs_convert_inline_data(struct inode *inode, struct page *page)
{
- int err;
+ int err = 0;
struct page *ipage;
struct dnode_of_data dn;
void *src_addr, *dst_addr;
goto out;
}
+ /* someone else converted inline_data already */
+ if (!f2fs_has_inline_data(inode))
+ goto out;
+
/*
* i_addr[0] is not used for inline data,
* so reserving new block will not destroy inline data
return err;
}
-int f2fs_convert_inline_data(struct inode *inode, pgoff_t to_size)
+int f2fs_convert_inline_data(struct inode *inode, pgoff_t to_size,
+ struct page *page)
{
- struct page *page;
+ struct page *new_page = page;
int err;
if (!f2fs_has_inline_data(inode))
else if (to_size <= MAX_INLINE_DATA)
return 0;
- page = grab_cache_page(inode->i_mapping, 0);
- if (!page)
- return -ENOMEM;
+ if (!page || page->index != 0) {
+ new_page = grab_cache_page(inode->i_mapping, 0);
+ if (!new_page)
+ return -ENOMEM;
+ }
- err = __f2fs_convert_inline_data(inode, page);
- f2fs_put_page(page, 1);
+ err = __f2fs_convert_inline_data(inode, new_page);
+ if (!page || page->index != 0)
+ f2fs_put_page(new_page, 1);
return err;
}
int f2fs_write_inline_data(struct inode *inode,
- struct page *page, unsigned size)
+ struct page *page, unsigned size)
{
void *src_addr, *dst_addr;
struct page *ipage;
f2fs_put_page(ipage, 1);
}
-int recover_inline_data(struct inode *inode, struct page *npage)
+bool recover_inline_data(struct inode *inode, struct page *npage)
{
struct f2fs_sb_info *sbi = F2FS_SB(inode->i_sb);
struct f2fs_inode *ri = NULL;
ri = F2FS_INODE(npage);
if (f2fs_has_inline_data(inode) &&
- ri && ri->i_inline & F2FS_INLINE_DATA) {
+ ri && (ri->i_inline & F2FS_INLINE_DATA)) {
process_inline:
ipage = get_node_page(sbi, inode->i_ino);
f2fs_bug_on(IS_ERR(ipage));
memcpy(dst_addr, src_addr, MAX_INLINE_DATA);
update_inode(inode, ipage);
f2fs_put_page(ipage, 1);
- return -1;
+ return true;
}
if (f2fs_has_inline_data(inode)) {
clear_inode_flag(F2FS_I(inode), FI_INLINE_DATA);
update_inode(inode, ipage);
f2fs_put_page(ipage, 1);
- } else if (ri && ri->i_inline & F2FS_INLINE_DATA) {
- truncate_blocks(inode, 0);
+ } else if (ri && (ri->i_inline & F2FS_INLINE_DATA)) {
+ truncate_blocks(inode, 0, false);
set_inode_flag(F2FS_I(inode), FI_INLINE_DATA);
goto process_inline;
}
- return 0;
+ return false;
}
return 0;
out:
clear_nlink(inode);
- unlock_new_inode(inode);
- make_bad_inode(inode);
- iput(inode);
+ iget_failed(inode);
alloc_nid_failed(sbi, ino);
return err;
}
f2fs_delete_entry(de, page, inode);
f2fs_unlock_op(sbi);
- /* In order to evict this inode, we set it dirty */
+ /* In order to evict this inode, we set it dirty */
mark_inode_dirty(inode);
fail:
trace_f2fs_unlink_exit(inode, err);
return err;
out:
clear_nlink(inode);
- unlock_new_inode(inode);
- make_bad_inode(inode);
- iput(inode);
+ iget_failed(inode);
alloc_nid_failed(sbi, inode->i_ino);
return err;
}
out_fail:
clear_inode_flag(F2FS_I(inode), FI_INC_LINK);
clear_nlink(inode);
- unlock_new_inode(inode);
- make_bad_inode(inode);
- iput(inode);
+ iget_failed(inode);
alloc_nid_failed(sbi, inode->i_ino);
return err;
}
return 0;
out:
clear_nlink(inode);
- unlock_new_inode(inode);
- make_bad_inode(inode);
- iput(inode);
+ iget_failed(inode);
alloc_nid_failed(sbi, inode->i_ino);
return err;
}
out:
f2fs_unlock_op(sbi);
clear_nlink(inode);
- unlock_new_inode(inode);
- make_bad_inode(inode);
- iput(inode);
+ iget_failed(inode);
alloc_nid_failed(sbi, inode->i_ino);
return err;
}
.mkdir = f2fs_mkdir,
.rmdir = f2fs_rmdir,
.mknod = f2fs_mknod,
- .rename = f2fs_rename,
.rename2 = f2fs_rename2,
.tmpfile = f2fs_tmpfile,
.getattr = f2fs_getattr,
nat_get_blkaddr(e) != NULL_ADDR &&
new_blkaddr == NEW_ADDR);
- /* increament version no as node is removed */
+ /* increment version no as node is removed */
if (nat_get_blkaddr(e) != NEW_ADDR && new_blkaddr == NULL_ADDR) {
unsigned char version = nat_get_version(e);
nat_set_version(e, inc_node_version(version));
}
/*
- * This function returns always success
+ * This function always returns success
*/
void get_node_info(struct f2fs_sb_info *sbi, nid_t nid, struct node_info *ni)
{
/* get indirect nodes in the path */
for (i = 0; i < idx + 1; i++) {
- /* refernece count'll be increased */
+ /* reference count'll be increased */
pages[i] = get_node_page(sbi, nid[i]);
if (IS_ERR(pages[i])) {
err = PTR_ERR(pages[i]);
*/
void remove_inode_page(struct inode *inode)
{
- struct f2fs_sb_info *sbi = F2FS_SB(inode->i_sb);
- struct page *page;
- nid_t ino = inode->i_ino;
struct dnode_of_data dn;
- page = get_node_page(sbi, ino);
- if (IS_ERR(page))
+ set_new_dnode(&dn, inode, NULL, NULL, inode->i_ino);
+ if (get_dnode_of_data(&dn, 0, LOOKUP_NODE))
return;
- if (truncate_xattr_node(inode, page)) {
- f2fs_put_page(page, 1);
+ if (truncate_xattr_node(inode, dn.inode_page)) {
+ f2fs_put_dnode(&dn);
return;
}
- /* 0 is possible, after f2fs_new_inode() is failed */
+
+ /* remove potential inline_data blocks */
+ if (S_ISREG(inode->i_mode) || S_ISDIR(inode->i_mode) ||
+ S_ISLNK(inode->i_mode))
+ truncate_data_blocks_range(&dn, 1);
+
+ /* 0 is possible, after f2fs_new_inode() has failed */
f2fs_bug_on(inode->i_blocks != 0 && inode->i_blocks != 1);
- set_new_dnode(&dn, inode, page, page, ino);
+
+ /* will put inode & node pages */
truncate_node(&dn);
}
set_fsync_mark(page, 0);
set_dentry_mark(page, 0);
}
- NODE_MAPPING(sbi)->a_ops->writepage(page, wbc);
- wrote++;
+
+ if (NODE_MAPPING(sbi)->a_ops->writepage(page, wbc))
+ unlock_page(page);
+ else
+ wrote++;
if (--wbc->nr_to_write == 0)
break;
if (unlikely(sbi->por_doing))
goto redirty_out;
+ if (unlikely(f2fs_cp_error(sbi)))
+ goto redirty_out;
f2fs_wait_on_page_writeback(page, NODE);
kmem_cache_free(free_nid_slab, i);
}
-void recover_node_page(struct f2fs_sb_info *sbi, struct page *page,
- struct f2fs_summary *sum, struct node_info *ni,
- block_t new_blkaddr)
-{
- rewrite_node_page(sbi, page, sum, ni->blk_addr, new_blkaddr);
- set_node_addr(sbi, ni, new_blkaddr, false);
- clear_node_page_dirty(page);
-}
-
void recover_inline_xattr(struct inode *inode, struct page *page)
{
struct f2fs_sb_info *sbi = F2FS_SB(inode->i_sb);
struct page *ipage;
struct f2fs_inode *ri;
- if (!f2fs_has_inline_xattr(inode))
- return;
-
- if (!IS_INODE(page))
- return;
-
- ri = F2FS_INODE(page);
- if (!(ri->i_inline & F2FS_INLINE_XATTR))
- return;
-
ipage = get_node_page(sbi, inode->i_ino);
f2fs_bug_on(IS_ERR(ipage));
+ ri = F2FS_INODE(page);
+ if (!(ri->i_inline & F2FS_INLINE_XATTR)) {
+ clear_inode_flag(F2FS_I(inode), FI_INLINE_XATTR);
+ goto update_inode;
+ }
+
dst_addr = inline_xattr_addr(ipage);
src_addr = inline_xattr_addr(page);
inline_size = inline_xattr_size(inode);
f2fs_wait_on_page_writeback(ipage, NODE);
memcpy(dst_addr, src_addr, inline_size);
-
+update_inode:
update_inode(inode, ipage);
f2fs_put_page(ipage, 1);
}
-bool recover_xattr_data(struct inode *inode, struct page *page, block_t blkaddr)
+void recover_xattr_data(struct inode *inode, struct page *page, block_t blkaddr)
{
struct f2fs_sb_info *sbi = F2FS_SB(inode->i_sb);
nid_t prev_xnid = F2FS_I(inode)->i_xattr_nid;
nid_t new_xnid = nid_of_node(page);
struct node_info ni;
- if (!f2fs_has_xattr_block(ofs_of_node(page)))
- return false;
-
/* 1: invalidate the previous xattr nid */
if (!prev_xnid)
goto recover_xnid;
set_node_addr(sbi, &ni, blkaddr, false);
update_inode_page(inode);
- return true;
}
int recover_inode_page(struct f2fs_sb_info *sbi, struct page *page)
if (!ipage)
return -ENOMEM;
- /* Should not use this inode from free nid list */
+ /* Should not use this inode from free nid list */
remove_free_nid(NM_I(sbi), ino);
SetPageUptodate(ipage);
dst->i_blocks = cpu_to_le64(1);
dst->i_links = cpu_to_le32(1);
dst->i_xattr_nid = 0;
+ dst->i_inline = src->i_inline & F2FS_INLINE_XATTR;
new_ni = old_ni;
new_ni.ino = ino;
WARN_ON(1);
set_node_addr(sbi, &new_ni, NEW_ADDR, false);
inc_valid_inode_count(sbi);
+ set_page_dirty(ipage);
f2fs_put_page(ipage, 1);
return 0;
}
/*
* ra_sum_pages() merge contiguous pages into one bio and submit.
- * these pre-readed pages are alloced in bd_inode's mapping tree.
+ * these pre-read pages are allocated in bd_inode's mapping tree.
*/
static int ra_sum_pages(struct f2fs_sb_info *sbi, struct page **pages,
int start, int nrpages)
for (i = 0; !err && i < last_offset; i += nrpages, addr += nrpages) {
nrpages = min(last_offset - i, bio_blocks);
- /* read ahead node pages */
+ /* readahead node pages */
nrpages = ra_sum_pages(sbi, pages, addr, nrpages);
if (!nrpages)
return -ENOMEM;
nm_i->max_nid = NAT_ENTRY_PER_BLOCK * nat_blocks;
/* not used nids: 0, node, meta, (and root counted as valid node) */
- nm_i->available_nids = nm_i->max_nid - 3;
+ nm_i->available_nids = nm_i->max_nid - F2FS_RESERVED_NODE_NUM;
nm_i->fcnt = 0;
nm_i->nat_cnt = 0;
nm_i->ram_thresh = DEF_RAM_THRESHOLD;
}
retry:
de = f2fs_find_entry(dir, &name, &page);
- if (de && inode->i_ino == le32_to_cpu(de->ino))
+ if (de && inode->i_ino == le32_to_cpu(de->ino)) {
+ clear_inode_flag(F2FS_I(inode), FI_INC_LINK);
goto out_unmap_put;
+ }
if (de) {
einode = f2fs_iget(inode->i_sb, le32_to_cpu(de->ino));
if (IS_ERR(einode)) {
struct node_info ni;
int err = 0, recovered = 0;
- recover_inline_xattr(inode, page);
-
- if (recover_inline_data(inode, page))
+ /* step 1: recover xattr */
+ if (IS_INODE(page)) {
+ recover_inline_xattr(inode, page);
+ } else if (f2fs_has_xattr_block(ofs_of_node(page))) {
+ recover_xattr_data(inode, page, blkaddr);
goto out;
+ }
- if (recover_xattr_data(inode, page, blkaddr))
+ /* step 2: recover inline data */
+ if (recover_inline_data(inode, page))
goto out;
+ /* step 3: recover data indices */
start = start_bidx_of_node(ofs_of_node(page), fi);
end = start + ADDRS_PER_PAGE(page, fi);
fill_node_footer(dn.node_page, dn.nid, ni.ino,
ofs_of_node(page), false);
set_page_dirty(dn.node_page);
-
- recover_node_page(sbi, dn.node_page, &sum, &ni, blkaddr);
err:
f2fs_put_dnode(&dn);
f2fs_unlock_op(sbi);
/* step #1: find fsynced inode numbers */
sbi->por_doing = true;
+ /* prevent checkpoint */
+ mutex_lock(&sbi->cp_mutex);
+
blkaddr = NEXT_FREE_BLKADDR(sbi, curseg);
err = find_fsync_dnodes(sbi, &inode_list);
/* step #2: recover data */
err = recover_data(sbi, &inode_list, CURSEG_WARM_NODE);
- f2fs_bug_on(!list_empty(&inode_list));
+ if (!err)
+ f2fs_bug_on(!list_empty(&inode_list));
out:
destroy_fsync_dnodes(&inode_list);
kmem_cache_destroy(fsync_entry_slab);
/* Flush all the NAT/SIT pages */
while (get_pages(sbi, F2FS_DIRTY_META))
sync_meta_pages(sbi, META, LONG_MAX);
+ set_ckpt_flags(sbi->ckpt, CP_ERROR_FLAG);
+ mutex_unlock(&sbi->cp_mutex);
} else if (need_writecp) {
+ mutex_unlock(&sbi->cp_mutex);
write_checkpoint(sbi, false);
+ } else {
+ mutex_unlock(&sbi->cp_mutex);
}
return err;
}
}
/*
- * __find_rev_next(_zero)_bit is copied from lib/find_next_bit.c becasue
+ * __find_rev_next(_zero)_bit is copied from lib/find_next_bit.c because
* f2fs_set_bit makes MSB and LSB reversed in a byte.
* Example:
* LSB <--> MSB
}
/*
- * This function always allocates a used segment (from dirty seglist) by SSR
+ * This function always allocates a used segment(from dirty seglist) by SSR
* manner, so it should recover the existing segment information of valid blocks
*/
static void change_curseg(struct f2fs_sb_info *sbi, int type, bool reuse)
mutex_unlock(&curseg->curseg_mutex);
}
-void rewrite_node_page(struct f2fs_sb_info *sbi,
- struct page *page, struct f2fs_summary *sum,
- block_t old_blkaddr, block_t new_blkaddr)
-{
- struct sit_info *sit_i = SIT_I(sbi);
- int type = CURSEG_WARM_NODE;
- struct curseg_info *curseg;
- unsigned int segno, old_cursegno;
- block_t next_blkaddr = next_blkaddr_of_node(page);
- unsigned int next_segno = GET_SEGNO(sbi, next_blkaddr);
- struct f2fs_io_info fio = {
- .type = NODE,
- .rw = WRITE_SYNC,
- };
-
- curseg = CURSEG_I(sbi, type);
-
- mutex_lock(&curseg->curseg_mutex);
- mutex_lock(&sit_i->sentry_lock);
-
- segno = GET_SEGNO(sbi, new_blkaddr);
- old_cursegno = curseg->segno;
-
- /* change the current segment */
- if (segno != curseg->segno) {
- curseg->next_segno = segno;
- change_curseg(sbi, type, true);
- }
- curseg->next_blkoff = GET_BLKOFF_FROM_SEG0(sbi, new_blkaddr);
- __add_sum_entry(sbi, type, sum);
-
- /* change the current log to the next block addr in advance */
- if (next_segno != segno) {
- curseg->next_segno = next_segno;
- change_curseg(sbi, type, true);
- }
- curseg->next_blkoff = GET_BLKOFF_FROM_SEG0(sbi, next_blkaddr);
-
- /* rewrite node page */
- set_page_writeback(page);
- f2fs_submit_page_mbio(sbi, page, new_blkaddr, &fio);
- f2fs_submit_merged_bio(sbi, NODE, WRITE);
- refresh_sit_entry(sbi, old_blkaddr, new_blkaddr);
- locate_dirty_segment(sbi, old_cursegno);
-
- mutex_unlock(&sit_i->sentry_lock);
- mutex_unlock(&curseg->curseg_mutex);
-}
-
static inline bool is_merged_page(struct f2fs_sb_info *sbi,
struct page *page, enum page_type type)
{
}
/*
- * Summary block is always treated as invalid block
+ * Summary block is always treated as an invalid block
*/
static inline void check_block_count(struct f2fs_sb_info *sbi,
int segno, struct f2fs_sit_entry *raw_sit)
stop_gc_thread(sbi);
/* We don't need to do checkpoint when it's clean */
- if (sbi->s_dirty && get_pages(sbi, F2FS_DIRTY_NODES))
+ if (sbi->s_dirty)
write_checkpoint(sbi, true);
+ /*
+ * normally superblock is clean, so we need to release this.
+ * In addition, EIO will skip do checkpoint, we need this as well.
+ */
+ release_dirty_inode(sbi);
+
iput(sbi->node_inode);
iput(sbi->meta_inode);
trace_f2fs_sync_fs(sb, sync);
- if (!sbi->s_dirty && !get_pages(sbi, F2FS_DIRTY_NODES))
- return 0;
-
if (sync) {
mutex_lock(&sbi->gc_mutex);
write_checkpoint(sbi, false);
buf->f_bfree = buf->f_blocks - valid_user_blocks(sbi) - ovp_count;
buf->f_bavail = user_block_count - valid_user_blocks(sbi);
- buf->f_files = sbi->total_node_count;
- buf->f_ffree = sbi->total_node_count - valid_inode_count(sbi);
+ buf->f_files = sbi->total_node_count - F2FS_RESERVED_NODE_NUM;
+ buf->f_ffree = buf->f_files - valid_inode_count(sbi);
buf->f_namelen = F2FS_NAME_LEN;
buf->f_fsid.val[0] = (u32)id;
if (need_restart_gc) {
if (start_gc_thread(sbi))
f2fs_msg(sbi->sb, KERN_WARNING,
- "background gc thread is stop");
+ "background gc thread has stopped");
} else if (need_stop_gc) {
stop_gc_thread(sbi);
}
if (unlikely(fsmeta >= total))
return 1;
- if (unlikely(is_set_ckpt_flags(ckpt, CP_ERROR_FLAG))) {
+ if (unlikely(f2fs_cp_error(sbi))) {
f2fs_msg(sbi->sb, KERN_ERR, "A bug case: need to run fsck");
return 1;
}
struct buffer_head *raw_super_buf;
struct inode *root;
long err = -EINVAL;
+ bool retry = true;
int i;
+try_onemore:
/* allocate memory for f2fs-specific super block info */
sbi = kzalloc(sizeof(struct f2fs_sb_info), GFP_KERNEL);
if (!sbi)
/* recover fsynced data */
if (!test_opt(sbi, DISABLE_ROLL_FORWARD)) {
err = recover_fsync_data(sbi);
- if (err)
+ if (err) {
f2fs_msg(sb, KERN_ERR,
"Cannot recover all fsync data errno=%ld", err);
+ goto free_kobj;
+ }
}
/*
brelse(raw_super_buf);
free_sbi:
kfree(sbi);
+
+ /* give only one another chance */
+ if (retry) {
+ retry = 0;
+ shrink_dcache_sb(sb);
+ goto try_onemore;
+ }
return err;
}
int free;
/*
* If value is NULL, it is remove operation.
- * In case of update operation, we caculate free.
+ * In case of update operation, we calculate free.
*/
free = MIN_OFFSET(inode) - ((char *)last - (char *)base_addr);
if (found)
struct commit_header *h;
__u32 csum;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
h = (struct commit_header *)(bh->b_data);
return checksum;
}
-static void write_tag_block(int tag_bytes, journal_block_tag_t *tag,
+static void write_tag_block(journal_t *j, journal_block_tag_t *tag,
unsigned long long block)
{
tag->t_blocknr = cpu_to_be32(block & (u32)~0);
- if (tag_bytes > JBD2_TAG_SIZE32)
+ if (JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_64BIT))
tag->t_blocknr_high = cpu_to_be32((block >> 31) >> 1);
}
struct jbd2_journal_block_tail *tail;
__u32 csum;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
tail = (struct jbd2_journal_block_tail *)(bh->b_data + j->j_blocksize -
static void jbd2_block_tag_csum_set(journal_t *j, journal_block_tag_t *tag,
struct buffer_head *bh, __u32 sequence)
{
+ journal_block_tag3_t *tag3 = (journal_block_tag3_t *)tag;
struct page *page = bh->b_page;
__u8 *addr;
__u32 csum32;
__be32 seq;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
seq = cpu_to_be32(sequence);
bh->b_size);
kunmap_atomic(addr);
- /* We only have space to store the lower 16 bits of the crc32c. */
- tag->t_checksum = cpu_to_be16(csum32);
+ if (JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V3))
+ tag3->t_checksum = cpu_to_be32(csum32);
+ else
+ tag->t_checksum = cpu_to_be16(csum32);
}
/*
* jbd2_journal_commit_transaction
LIST_HEAD(io_bufs);
LIST_HEAD(log_bufs);
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
csum_size = sizeof(struct jbd2_journal_block_tail);
/*
tag_flag |= JBD2_FLAG_SAME_UUID;
tag = (journal_block_tag_t *) tagp;
- write_tag_block(tag_bytes, tag, jh2bh(jh)->b_blocknr);
+ write_tag_block(journal, tag, jh2bh(jh)->b_blocknr);
tag->t_flags = cpu_to_be16(tag_flag);
jbd2_block_tag_csum_set(journal, tag, wbuf[bufs],
commit_transaction->t_tid);
/* Checksumming functions */
static int jbd2_verify_csum_type(journal_t *j, journal_superblock_t *sb)
{
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
return sb->s_checksum_type == JBD2_CRC32C_CHKSUM;
static int jbd2_superblock_csum_verify(journal_t *j, journal_superblock_t *sb)
{
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
return sb->s_checksum == jbd2_superblock_csum(j, sb);
static void jbd2_superblock_csum_set(journal_t *j, journal_superblock_t *sb)
{
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
sb->s_checksum = jbd2_superblock_csum(j, sb);
goto out;
}
- if (JBD2_HAS_COMPAT_FEATURE(journal, JBD2_FEATURE_COMPAT_CHECKSUM) &&
- JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2)) {
+ if (jbd2_journal_has_csum_v2or3(journal) &&
+ JBD2_HAS_COMPAT_FEATURE(journal, JBD2_FEATURE_COMPAT_CHECKSUM)) {
/* Can't have checksum v1 and v2 on at the same time! */
printk(KERN_ERR "JBD2: Can't enable checksumming v1 and v2 "
"at the same time!\n");
goto out;
}
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2) &&
+ JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V3)) {
+ /* Can't have checksum v2 and v3 at the same time! */
+ printk(KERN_ERR "JBD2: Can't enable checksumming v2 and v3 "
+ "at the same time!\n");
+ goto out;
+ }
+
if (!jbd2_verify_csum_type(journal, sb)) {
printk(KERN_ERR "JBD2: Unknown checksum type\n");
goto out;
}
/* Load the checksum driver */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2)) {
+ if (jbd2_journal_has_csum_v2or3(journal)) {
journal->j_chksum_driver = crypto_alloc_shash("crc32c", 0, 0);
if (IS_ERR(journal->j_chksum_driver)) {
printk(KERN_ERR "JBD2: Cannot load crc32c driver.\n");
}
/* Precompute checksum seed for all metadata */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
journal->j_csum_seed = jbd2_chksum(journal, ~0, sb->s_uuid,
sizeof(sb->s_uuid));
if (!jbd2_journal_check_available_features(journal, compat, ro, incompat))
return 0;
- /* Asking for checksumming v2 and v1? Only give them v2. */
- if (incompat & JBD2_FEATURE_INCOMPAT_CSUM_V2 &&
+ /* If enabling v2 checksums, turn on v3 instead */
+ if (incompat & JBD2_FEATURE_INCOMPAT_CSUM_V2) {
+ incompat &= ~JBD2_FEATURE_INCOMPAT_CSUM_V2;
+ incompat |= JBD2_FEATURE_INCOMPAT_CSUM_V3;
+ }
+
+ /* Asking for checksumming v3 and v1? Only give them v3. */
+ if (incompat & JBD2_FEATURE_INCOMPAT_CSUM_V3 &&
compat & JBD2_FEATURE_COMPAT_CHECKSUM)
compat &= ~JBD2_FEATURE_COMPAT_CHECKSUM;
sb = journal->j_superblock;
- /* If enabling v2 checksums, update superblock */
- if (INCOMPAT_FEATURE_ON(JBD2_FEATURE_INCOMPAT_CSUM_V2)) {
+ /* If enabling v3 checksums, update superblock */
+ if (INCOMPAT_FEATURE_ON(JBD2_FEATURE_INCOMPAT_CSUM_V3)) {
sb->s_checksum_type = JBD2_CRC32C_CHKSUM;
sb->s_feature_compat &=
~cpu_to_be32(JBD2_FEATURE_COMPAT_CHECKSUM);
}
/* Precompute checksum seed for all metadata */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal,
- JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
journal->j_csum_seed = jbd2_chksum(journal, ~0,
sb->s_uuid,
sizeof(sb->s_uuid));
/* If enabling v1 checksums, downgrade superblock */
if (COMPAT_FEATURE_ON(JBD2_FEATURE_COMPAT_CHECKSUM))
sb->s_feature_incompat &=
- ~cpu_to_be32(JBD2_FEATURE_INCOMPAT_CSUM_V2);
+ ~cpu_to_be32(JBD2_FEATURE_INCOMPAT_CSUM_V2 |
+ JBD2_FEATURE_INCOMPAT_CSUM_V3);
sb->s_feature_compat |= cpu_to_be32(compat);
sb->s_feature_ro_compat |= cpu_to_be32(ro);
*/
size_t journal_tag_bytes(journal_t *journal)
{
- journal_block_tag_t tag;
- size_t x = 0;
+ size_t sz;
+
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V3))
+ return sizeof(journal_block_tag3_t);
+
+ sz = sizeof(journal_block_tag_t);
if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
- x += sizeof(tag.t_checksum);
+ sz += sizeof(__u16);
if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_64BIT))
- return x + JBD2_TAG_SIZE64;
+ return sz;
else
- return x + JBD2_TAG_SIZE32;
+ return sz - sizeof(__u32);
}
/*
__be32 provided;
__u32 calculated;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
tail = (struct jbd2_journal_block_tail *)(buf + j->j_blocksize -
int nr = 0, size = journal->j_blocksize;
int tag_bytes = journal_tag_bytes(journal);
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
size -= sizeof(struct jbd2_journal_block_tail);
tagp = &bh->b_data[sizeof(journal_header_t)];
return err;
}
-static inline unsigned long long read_tag_block(int tag_bytes, journal_block_tag_t *tag)
+static inline unsigned long long read_tag_block(journal_t *journal,
+ journal_block_tag_t *tag)
{
unsigned long long block = be32_to_cpu(tag->t_blocknr);
- if (tag_bytes > JBD2_TAG_SIZE32)
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_64BIT))
block |= (u64)be32_to_cpu(tag->t_blocknr_high) << 32;
return block;
}
__be32 provided;
__u32 calculated;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
h = buf;
static int jbd2_block_tag_csum_verify(journal_t *j, journal_block_tag_t *tag,
void *buf, __u32 sequence)
{
+ journal_block_tag3_t *tag3 = (journal_block_tag3_t *)tag;
__u32 csum32;
__be32 seq;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
seq = cpu_to_be32(sequence);
csum32 = jbd2_chksum(j, j->j_csum_seed, (__u8 *)&seq, sizeof(seq));
csum32 = jbd2_chksum(j, csum32, buf, j->j_blocksize);
- return tag->t_checksum == cpu_to_be16(csum32);
+ if (JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V3))
+ return tag3->t_checksum == cpu_to_be32(csum32);
+ else
+ return tag->t_checksum == cpu_to_be16(csum32);
}
static int do_one_pass(journal_t *journal,
int tag_bytes = journal_tag_bytes(journal);
__u32 crc32_sum = ~0; /* Transactional Checksums */
int descr_csum_size = 0;
+ int block_error = 0;
/*
* First thing is to establish what we expect to find in the log
switch(blocktype) {
case JBD2_DESCRIPTOR_BLOCK:
/* Verify checksum first */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal,
- JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
descr_csum_size =
sizeof(struct jbd2_journal_block_tail);
if (descr_csum_size > 0 &&
unsigned long long blocknr;
J_ASSERT(obh != NULL);
- blocknr = read_tag_block(tag_bytes,
+ blocknr = read_tag_block(journal,
tag);
/* If the block has been
"checksum recovering "
"block %llu in log\n",
blocknr);
- continue;
+ block_error = 1;
+ goto skip_write;
}
/* Find a buffer for the new
success = -EIO;
}
}
-
+ if (block_error && success == 0)
+ success = -EIO;
return success;
failed:
__be32 provided;
__u32 calculated;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
tail = (struct jbd2_journal_revoke_tail *)(buf + j->j_blocksize -
#include <linux/list.h>
#include <linux/init.h>
#include <linux/bio.h>
-#endif
#include <linux/log2.h>
+#endif
static struct kmem_cache *jbd2_revoke_record_cache;
static struct kmem_cache *jbd2_revoke_table_cache;
offset = *offsetp;
/* Do we need to leave space at the end for a checksum? */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
csum_size = sizeof(struct jbd2_journal_revoke_tail);
/* Make sure we have a descriptor with space left for the record */
struct jbd2_journal_revoke_tail *tail;
__u32 csum;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
tail = (struct jbd2_journal_revoke_tail *)(bh->b_data + j->j_blocksize -
smp_mb();
error = check_conflicting_open(dentry, arg);
if (error)
- locks_unlink_lock(flp);
+ locks_unlink_lock(before);
out:
if (is_deleg)
mutex_unlock(&inode->i_mutex);
.rpc_argp = &args,
.rpc_resp = &fattr,
};
- int status;
+ int status = 0;
+
+ if (acl == NULL && (!S_ISDIR(inode->i_mode) || dfacl == NULL))
+ goto out;
status = -EOPNOTSUPP;
if (!nfs_server_capable(inode, NFS_CAP_ACLS))
struct nfs4_closedata *calldata = data;
struct nfs4_state *state = calldata->state;
struct nfs_server *server = NFS_SERVER(calldata->inode);
+ nfs4_stateid *res_stateid = NULL;
dprintk("%s: begin!\n", __func__);
if (!nfs4_sequence_done(task, &calldata->res.seq_res))
*/
switch (task->tk_status) {
case 0:
- if (calldata->roc)
+ res_stateid = &calldata->res.stateid;
+ if (calldata->arg.fmode == 0 && calldata->roc)
pnfs_roc_set_barrier(state->inode,
calldata->roc_barrier);
- nfs_clear_open_stateid(state, &calldata->res.stateid, 0);
renew_lease(server, calldata->timestamp);
- goto out_release;
+ break;
case -NFS4ERR_ADMIN_REVOKED:
case -NFS4ERR_STALE_STATEID:
case -NFS4ERR_OLD_STATEID:
goto out_release;
}
}
- nfs_clear_open_stateid(state, NULL, calldata->arg.fmode);
+ nfs_clear_open_stateid(state, res_stateid, calldata->arg.fmode);
out_release:
nfs_release_seqid(calldata->arg.seqid);
nfs_refresh_inode(calldata->inode, calldata->res.fattr);
struct nfs4_closedata *calldata = data;
struct nfs4_state *state = calldata->state;
struct inode *inode = calldata->inode;
+ bool is_rdonly, is_wronly, is_rdwr;
int call_close = 0;
dprintk("%s: begin!\n", __func__);
goto out_wait;
task->tk_msg.rpc_proc = &nfs4_procedures[NFSPROC4_CLNT_OPEN_DOWNGRADE];
- calldata->arg.fmode = FMODE_READ|FMODE_WRITE;
spin_lock(&state->owner->so_lock);
+ is_rdwr = test_bit(NFS_O_RDWR_STATE, &state->flags);
+ is_rdonly = test_bit(NFS_O_RDONLY_STATE, &state->flags);
+ is_wronly = test_bit(NFS_O_WRONLY_STATE, &state->flags);
+ /* Calculate the current open share mode */
+ calldata->arg.fmode = 0;
+ if (is_rdonly || is_rdwr)
+ calldata->arg.fmode |= FMODE_READ;
+ if (is_wronly || is_rdwr)
+ calldata->arg.fmode |= FMODE_WRITE;
/* Calculate the change in open mode */
if (state->n_rdwr == 0) {
if (state->n_rdonly == 0) {
- call_close |= test_bit(NFS_O_RDONLY_STATE, &state->flags);
- call_close |= test_bit(NFS_O_RDWR_STATE, &state->flags);
+ call_close |= is_rdonly || is_rdwr;
calldata->arg.fmode &= ~FMODE_READ;
}
if (state->n_wronly == 0) {
- call_close |= test_bit(NFS_O_WRONLY_STATE, &state->flags);
- call_close |= test_bit(NFS_O_RDWR_STATE, &state->flags);
+ call_close |= is_wronly || is_rdwr;
calldata->arg.fmode &= ~FMODE_WRITE;
}
}
}
out:
- spin_unlock(&qs->qs_lock);
- if (fence)
+ if (fence) {
+ spin_unlock(&qs->qs_lock);
o2quo_fence_self();
+ } else {
+ mlog(ML_NOTICE, "not fencing this node, heartbeating: %d, "
+ "connected: %d, lowest: %d (%sreachable)\n",
+ qs->qs_heartbeating, qs->qs_connected, lowest_hb,
+ lowest_reachable ? "" : "un");
+ spin_unlock(&qs->qs_lock);
+
+ }
+
}
static void o2quo_set_hold(struct o2quo_state *qs, u8 node)
return ret;
}
+static int o2net_set_usertimeout(struct socket *sock)
+{
+ int user_timeout = O2NET_TCP_USER_TIMEOUT;
+
+ return kernel_setsockopt(sock, SOL_TCP, TCP_USER_TIMEOUT,
+ (char *)&user_timeout, sizeof(user_timeout));
+}
+
static void o2net_initialize_handshake(void)
{
o2net_hand->o2hb_heartbeat_timeout_ms = cpu_to_be32(
#endif
printk(KERN_NOTICE "o2net: Connection to " SC_NODEF_FMT " has been "
- "idle for %lu.%lu secs, shutting it down.\n", SC_NODEF_ARGS(sc),
- msecs / 1000, msecs % 1000);
+ "idle for %lu.%lu secs.\n",
+ SC_NODEF_ARGS(sc), msecs / 1000, msecs % 1000);
- /*
- * Initialize the nn_timeout so that the next connection attempt
- * will continue in o2net_start_connect.
+ /* idle timerout happen, don't shutdown the connection, but
+ * make fence decision. Maybe the connection can recover before
+ * the decision is made.
*/
atomic_set(&nn->nn_timeout, 1);
+ o2quo_conn_err(o2net_num_from_nn(nn));
+ queue_delayed_work(o2net_wq, &nn->nn_still_up,
+ msecs_to_jiffies(O2NET_QUORUM_DELAY_MS));
+
+ o2net_sc_reset_idle_timer(sc);
- o2net_sc_queue_work(sc, &sc->sc_shutdown_work);
}
static void o2net_sc_reset_idle_timer(struct o2net_sock_container *sc)
static void o2net_sc_postpone_idle(struct o2net_sock_container *sc)
{
+ struct o2net_node *nn = o2net_nn_from_num(sc->sc_node->nd_num);
+
+ /* clear fence decision since the connection recover from timeout*/
+ if (atomic_read(&nn->nn_timeout)) {
+ o2quo_conn_up(o2net_num_from_nn(nn));
+ cancel_delayed_work(&nn->nn_still_up);
+ atomic_set(&nn->nn_timeout, 0);
+ }
+
/* Only push out an existing timer */
if (timer_pending(&sc->sc_idle_timeout))
o2net_sc_reset_idle_timer(sc);
goto out;
}
+ ret = o2net_set_usertimeout(sock);
+ if (ret) {
+ mlog(ML_ERROR, "set TCP_USER_TIMEOUT failed with %d\n", ret);
+ goto out;
+ }
+
o2net_register_callbacks(sc->sc_sock->sk, sc);
spin_lock(&nn->nn_lock);
goto out;
}
+ ret = o2net_set_usertimeout(new_sock);
+ if (ret) {
+ mlog(ML_ERROR, "set TCP_USER_TIMEOUT failed with %d\n", ret);
+ goto out;
+ }
+
slen = sizeof(sin);
ret = new_sock->ops->getname(new_sock, (struct sockaddr *) &sin,
&slen, 1);
#define O2NET_KEEPALIVE_DELAY_MS_DEFAULT 2000
#define O2NET_IDLE_TIMEOUT_MS_DEFAULT 30000
+#define O2NET_TCP_USER_TIMEOUT 0x7fffffff
/* TODO: figure this out.... */
static inline int o2net_link_down(int err, struct socket *sock)
copy_to_user((typeof(a) __user *)b, &(a), sizeof(a))
/*
- * This call is void because we are already reporting an error that may
- * be -EFAULT. The error will be returned from the ioctl(2) call. It's
- * just a best-effort to tell userspace that this request caused the error.
+ * This is just a best-effort to tell userspace that this request
+ * caused the error.
*/
static inline void o2info_set_request_error(struct ocfs2_info_request *kreq,
struct ocfs2_info_request __user *req)
static int ocfs2_info_handle_blocksize(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_blocksize oib;
if (o2info_from_user(oib, req))
- goto bail;
+ return -EFAULT;
oib.ib_blocksize = inode->i_sb->s_blocksize;
o2info_set_request_filled(&oib.ib_req);
if (o2info_to_user(oib, req))
- goto bail;
-
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oib.ib_req, req);
+ return -EFAULT;
- return status;
+ return 0;
}
static int ocfs2_info_handle_clustersize(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_clustersize oic;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oic, req))
- goto bail;
+ return -EFAULT;
oic.ic_clustersize = osb->s_clustersize;
o2info_set_request_filled(&oic.ic_req);
if (o2info_to_user(oic, req))
- goto bail;
-
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oic.ic_req, req);
+ return -EFAULT;
- return status;
+ return 0;
}
static int ocfs2_info_handle_maxslots(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_maxslots oim;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oim, req))
- goto bail;
+ return -EFAULT;
oim.im_max_slots = osb->max_slots;
o2info_set_request_filled(&oim.im_req);
if (o2info_to_user(oim, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oim.im_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_label(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_label oil;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oil, req))
- goto bail;
+ return -EFAULT;
memcpy(oil.il_label, osb->vol_label, OCFS2_MAX_VOL_LABEL_LEN);
o2info_set_request_filled(&oil.il_req);
if (o2info_to_user(oil, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oil.il_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_uuid(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_uuid oiu;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oiu, req))
- goto bail;
+ return -EFAULT;
memcpy(oiu.iu_uuid_str, osb->uuid_str, OCFS2_TEXT_UUID_LEN + 1);
o2info_set_request_filled(&oiu.iu_req);
if (o2info_to_user(oiu, req))
- goto bail;
-
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oiu.iu_req, req);
+ return -EFAULT;
- return status;
+ return 0;
}
static int ocfs2_info_handle_fs_features(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_fs_features oif;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oif, req))
- goto bail;
+ return -EFAULT;
oif.if_compat_features = osb->s_feature_compat;
oif.if_incompat_features = osb->s_feature_incompat;
o2info_set_request_filled(&oif.if_req);
if (o2info_to_user(oif, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oif.if_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_journal_size(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_journal_size oij;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oij, req))
- goto bail;
+ return -EFAULT;
oij.ij_journal_size = i_size_read(osb->journal->j_inode);
o2info_set_request_filled(&oij.ij_req);
if (o2info_to_user(oij, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oij.ij_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_scan_inode_alloc(struct ocfs2_super *osb,
u32 i;
u64 blkno = -1;
char namebuf[40];
- int status = -EFAULT, type = INODE_ALLOC_SYSTEM_INODE;
+ int status, type = INODE_ALLOC_SYSTEM_INODE;
struct ocfs2_info_freeinode *oifi = NULL;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
struct inode *inode_alloc = NULL;
goto out_err;
}
- if (o2info_from_user(*oifi, req))
- goto bail;
+ if (o2info_from_user(*oifi, req)) {
+ status = -EFAULT;
+ goto out_free;
+ }
oifi->ifi_slotnum = osb->max_slots;
o2info_set_request_filled(&oifi->ifi_req);
- if (o2info_to_user(*oifi, req))
- goto bail;
+ if (o2info_to_user(*oifi, req)) {
+ status = -EFAULT;
+ goto out_free;
+ }
status = 0;
bail:
if (status)
o2info_set_request_error(&oifi->ifi_req, req);
-
+out_free:
kfree(oifi);
out_err:
return status;
{
u64 blkno = -1;
char namebuf[40];
- int status = -EFAULT, type = GLOBAL_BITMAP_SYSTEM_INODE;
+ int status, type = GLOBAL_BITMAP_SYSTEM_INODE;
struct ocfs2_info_freefrag *oiff;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
goto out_err;
}
- if (o2info_from_user(*oiff, req))
- goto bail;
+ if (o2info_from_user(*oiff, req)) {
+ status = -EFAULT;
+ goto out_free;
+ }
/*
* chunksize from userspace should be power of 2.
*/
if (o2info_to_user(*oiff, req)) {
status = -EFAULT;
- goto bail;
+ goto out_free;
}
status = 0;
bail:
if (status)
o2info_set_request_error(&oiff->iff_req, req);
-
+out_free:
kfree(oiff);
out_err:
return status;
static int ocfs2_info_handle_unknown(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_request oir;
if (o2info_from_user(oir, req))
- goto bail;
+ return -EFAULT;
o2info_clear_request_filled(&oir);
if (o2info_to_user(oir, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oir, req);
-
- return status;
+ return 0;
}
/*
BLK_MQ_RQ_QUEUE_ERROR = 2, /* end IO with error */
BLK_MQ_F_SHOULD_MERGE = 1 << 0,
- BLK_MQ_F_SHOULD_SORT = 1 << 1,
- BLK_MQ_F_TAG_SHARED = 1 << 2,
- BLK_MQ_F_SG_MERGE = 1 << 3,
- BLK_MQ_F_SYSFS_UP = 1 << 4,
+ BLK_MQ_F_TAG_SHARED = 1 << 1,
+ BLK_MQ_F_SG_MERGE = 1 << 2,
+ BLK_MQ_F_SYSFS_UP = 1 << 3,
BLK_MQ_S_STOPPED = 0,
BLK_MQ_S_TAG_ACTIVE = 1,
#define NULL_ADDR ((block_t)0) /* used as block_t addresses */
#define NEW_ADDR ((block_t)-1) /* used as block_t addresses */
+/* 0, 1(node nid), 2(meta nid) are reserved node id */
+#define F2FS_RESERVED_NODE_NUM 3
+
#define F2FS_ROOT_INO(sbi) (sbi->root_ino_num)
#define F2FS_NODE_INO(sbi) (sbi->node_ino_num)
#define F2FS_META_INO(sbi) (sbi->meta_ino_num)
#define CP_ORPHAN_PRESENT_FLAG 0x00000002
#define CP_UMOUNT_FLAG 0x00000001
+#define F2FS_CP_PACKS 2 /* # of checkpoint packs */
+
struct f2fs_checkpoint {
__le64 checkpoint_ver; /* checkpoint block version number */
__le64 user_block_count; /* # of user blocks */
*/
#define F2FS_ORPHANS_PER_BLOCK 1020
+#define GET_ORPHAN_BLOCKS(n) ((n + F2FS_ORPHANS_PER_BLOCK - 1) / \
+ F2FS_ORPHANS_PER_BLOCK)
+
struct f2fs_orphan_block {
__le32 ino[F2FS_ORPHANS_PER_BLOCK]; /* inode numbers */
__le32 reserved; /* reserved */
#define F2FS_NAME_LEN 255
#define F2FS_INLINE_XATTR_ADDRS 50 /* 200 bytes for inline xattrs */
#define DEF_ADDRS_PER_INODE 923 /* Address Pointers in an Inode */
+#define DEF_NIDS_PER_INODE 5 /* Node IDs in an Inode */
#define ADDRS_PER_INODE(fi) addrs_per_inode(fi)
#define ADDRS_PER_BLOCK 1018 /* Address Pointers in a Direct Block */
#define NIDS_PER_BLOCK 1018 /* Node IDs in an Indirect Block */
#define MAX_INLINE_DATA (sizeof(__le32) * (DEF_ADDRS_PER_INODE - \
F2FS_INLINE_XATTR_ADDRS - 1))
-#define INLINE_DATA_OFFSET (PAGE_CACHE_SIZE - sizeof(struct node_footer) \
- - sizeof(__le32) * (DEF_ADDRS_PER_INODE + 5 - 1))
+#define INLINE_DATA_OFFSET (PAGE_CACHE_SIZE - sizeof(struct node_footer) -\
+ sizeof(__le32) * (DEF_ADDRS_PER_INODE + \
+ DEF_NIDS_PER_INODE - 1))
struct f2fs_inode {
__le16 i_mode; /* file mode */
__le32 i_addr[DEF_ADDRS_PER_INODE]; /* Pointers to data blocks */
- __le32 i_nid[5]; /* direct(2), indirect(2),
+ __le32 i_nid[DEF_NIDS_PER_INODE]; /* direct(2), indirect(2),
double_indirect(1) node id */
} __packed;
* journal_block_tag (in the descriptor). The other h_chksum* fields are
* not used.
*
- * Checksum v1 and v2 are mutually exclusive features.
+ * If FEATURE_INCOMPAT_CSUM_V3 is set, the descriptor block uses
+ * journal_block_tag3_t to store a full 32-bit checksum. Everything else
+ * is the same as v2.
+ *
+ * Checksum v1, v2, and v3 are mutually exclusive features.
*/
struct commit_header {
__be32 h_magic;
* raw struct shouldn't be used for pointer math or sizeof() - use
* journal_tag_bytes(journal) instead to compute this.
*/
+typedef struct journal_block_tag3_s
+{
+ __be32 t_blocknr; /* The on-disk block number */
+ __be32 t_flags; /* See below */
+ __be32 t_blocknr_high; /* most-significant high 32bits. */
+ __be32 t_checksum; /* crc32c(uuid+seq+block) */
+} journal_block_tag3_t;
+
typedef struct journal_block_tag_s
{
__be32 t_blocknr; /* The on-disk block number */
__be32 t_blocknr_high; /* most-significant high 32bits. */
} journal_block_tag_t;
-#define JBD2_TAG_SIZE32 (offsetof(journal_block_tag_t, t_blocknr_high))
-#define JBD2_TAG_SIZE64 (sizeof(journal_block_tag_t))
-
/* Tail of descriptor block, for checksumming */
struct jbd2_journal_block_tail {
__be32 t_checksum; /* crc32c(uuid+descr_block) */
#define JBD2_FEATURE_INCOMPAT_64BIT 0x00000002
#define JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT 0x00000004
#define JBD2_FEATURE_INCOMPAT_CSUM_V2 0x00000008
+#define JBD2_FEATURE_INCOMPAT_CSUM_V3 0x00000010
/* Features known to this kernel version: */
#define JBD2_KNOWN_COMPAT_FEATURES JBD2_FEATURE_COMPAT_CHECKSUM
#define JBD2_KNOWN_INCOMPAT_FEATURES (JBD2_FEATURE_INCOMPAT_REVOKE | \
JBD2_FEATURE_INCOMPAT_64BIT | \
JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT | \
- JBD2_FEATURE_INCOMPAT_CSUM_V2)
+ JBD2_FEATURE_INCOMPAT_CSUM_V2 | \
+ JBD2_FEATURE_INCOMPAT_CSUM_V3)
#ifdef __KERNEL__
extern int jbd2_journal_blocks_per_page(struct inode *inode);
extern size_t journal_tag_bytes(journal_t *journal);
+static inline int jbd2_journal_has_csum_v2or3(journal_t *journal)
+{
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2) ||
+ JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V3))
+ return 1;
+
+ return 0;
+}
+
/*
* We reserve t_outstanding_credits >> JBD2_CONTROL_BLOCKS_SHIFT for
* transaction control blocks.
#include <linux/list.h>
#include <linux/spinlock.h>
#include <linux/rwsem.h>
+#include <linux/timer.h>
#include <linux/workqueue.h>
struct device;
const char *default_trigger; /* Trigger to use */
unsigned long blink_delay_on, blink_delay_off;
- struct delayed_work blink_work;
+ struct timer_list blink_timer;
int blink_brightness;
struct work_struct set_brightness_work;
};
enum omap_ecc {
- /* 1-bit ECC calculation by GPMC, Error detection by Software */
- OMAP_ECC_HAM1_CODE_HW = 0,
+ /*
+ * 1-bit ECC: calculation and correction by SW
+ * ECC stored at end of spare area
+ */
+ OMAP_ECC_HAM1_CODE_SW = 0,
+
+ /*
+ * 1-bit ECC: calculation by GPMC, Error detection by Software
+ * ECC layout compatible with ROM code layout
+ */
+ OMAP_ECC_HAM1_CODE_HW,
/* 4-bit ECC calculation by GPMC, Error detection by Software */
OMAP_ECC_BCH4_CODE_HW_DETECTION_SW,
/* 4-bit ECC calculation by GPMC, Error detection by ELM */
* @context: the execution context this fence is a part of
* @seqno_ofs: the offset within @sync_buf
* @seqno: the sequence # to signal on
+ * @cond: fence wait condition
* @ops: the fence_ops for operations on this seqno fence
*
* This function initializes a struct seqno_fence with passed parameters,
* the device whose settings are being modified.
* @transfer: adds a message to the controller's transfer queue.
* @cleanup: frees controller-specific state
+ * @can_dma: determine whether this master supports DMA
* @queued: whether this master is providing an internal message queue
* @kworker: thread struct for message pump
* @kworker_task: pointer to task for message pump kworker thread
* @cur_msg: the currently in-flight message
* @cur_msg_prepared: spi_prepare_message was called for the currently
* in-flight message
+ * @cur_msg_mapped: message has been mapped for DMA
* @xfer_completion: used by core transfer_one_message()
* @busy: message pump is busy
* @running: message pump is running
* @cs_gpios: Array of GPIOs to use as chip select lines; one per CS
* number. Any individual value may be -ENOENT for CS lines that
* are not GPIOs (driven by the SPI controller itself).
+ * @dma_tx: DMA transmit channel
+ * @dma_rx: DMA receive channel
+ * @dummy_rx: dummy receive buffer for full-duplex devices
+ * @dummy_tx: dummy transmit buffer for full-duplex devices
*
* Each SPI master controller can communicate with one or more @spi_device
* children. These make a small bus, sharing MOSI, MISO and SCK signals
* addresses for each transfer buffer
* @complete: called to report transaction completions
* @context: the argument to complete() when it's called
+ * @frame_length: the total number of bytes in the message
* @actual_length: the total number of bytes that were transferred in all
* successful segments
* @status: zero for success, else negative errno
.access = SNDRV_CTL_ELEM_ACCESS_TLV_READWRITE | \
SNDRV_CTL_ELEM_ACCESS_TLV_CALLBACK, \
.tlv.c = (snd_soc_bytes_tlv_callback), \
- .info = snd_soc_info_bytes_ext, \
+ .info = snd_soc_bytes_info_ext, \
.private_value = (unsigned long)&(struct soc_bytes_ext) \
{.max = xcount, .get = xhandler_get, .put = xhandler_put, } }
#define SOC_SINGLE_XR_SX(xname, xregbase, xregcount, xnbits, \
#ifndef _UAPI_LINUX_XATTR_H
#define _UAPI_LINUX_XATTR_H
-#ifdef __UAPI_DEF_XATTR
+#if __UAPI_DEF_XATTR
#define __USE_KERNEL_XATTR_DEFS
#define XATTR_CREATE 0x1 /* set value, fail if attr already exists */
chip->irq_eoi(&desc->irq_data);
raw_spin_unlock(&desc->lock);
}
+EXPORT_SYMBOL_GPL(handle_fasteoi_irq);
/**
* handle_edge_irq - edge type IRQ handler
char __weak kexec_purgatory[0];
size_t __weak kexec_purgatory_size = 0;
+#ifdef CONFIG_KEXEC_FILE
static int kexec_calculate_store_digests(struct kimage *image);
+#endif
/* Location of the reserved area for the crash kernel */
struct resource crashk_res = {
return ret;
}
+#ifdef CONFIG_KEXEC_FILE
static int copy_file_from_fd(int fd, void **buf, unsigned long *buf_len)
{
struct fd f = fdget(fd);
kfree(image);
return ret;
}
+#else /* CONFIG_KEXEC_FILE */
+static inline void kimage_file_post_load_cleanup(struct kimage *image) { }
+#endif /* CONFIG_KEXEC_FILE */
static int kimage_is_destination_range(struct kimage *image,
unsigned long start,
}
#endif
+#ifdef CONFIG_KEXEC_FILE
SYSCALL_DEFINE5(kexec_file_load, int, kernel_fd, int, initrd_fd,
unsigned long, cmdline_len, const char __user *, cmdline_ptr,
unsigned long, flags)
return ret;
}
+#endif /* CONFIG_KEXEC_FILE */
+
void crash_kexec(struct pt_regs *regs)
{
/* Take the kexec_mutex here to prevent sys_kexec_load
subsys_initcall(crash_save_vmcoreinfo_init);
+#ifdef CONFIG_KEXEC_FILE
static int __kexec_add_segment(struct kimage *image, char *buf,
unsigned long bufsz, unsigned long mem,
unsigned long memsz)
return 0;
}
+#endif /* CONFIG_KEXEC_FILE */
/*
* Move into place and start executing a preloaded standalone
end = res->end;
BUG_ON(start >= end);
- read_lock(&resource_lock);
-
- if (first_level_children_only) {
- p = iomem_resource.child;
+ if (first_level_children_only)
sibling_only = true;
- } else
- p = &iomem_resource;
- while ((p = next_resource(p, sibling_only))) {
+ read_lock(&resource_lock);
+
+ for (p = iomem_resource.child; p; p = next_resource(p, sibling_only)) {
if (p->flags != res->flags)
continue;
if (name && strcmp(p->name, name))
work = &cpu_buffer->irq_work;
}
- work->waiters_pending = true;
poll_wait(filp, &work->waiters, poll_table);
+ work->waiters_pending = true;
+ /*
+ * There's a tight race between setting the waiters_pending and
+ * checking if the ring buffer is empty. Once the waiters_pending bit
+ * is set, the next event will wake the task up, but we can get stuck
+ * if there's only a single event in.
+ *
+ * FIXME: Ideally, we need a memory barrier on the writer side as well,
+ * but adding a memory barrier to all events will cause too much of a
+ * performance hit in the fast path. We only need a memory barrier when
+ * the buffer goes from empty to having content. But as this race is
+ * extremely small, and it's not a problem if another event comes in, we
+ * will fix it later.
+ */
+ smp_mb();
if ((cpu == RING_BUFFER_ALL_CPUS && !ring_buffer_empty(buffer)) ||
(cpu != RING_BUFFER_ALL_CPUS && !ring_buffer_empty_cpu(buffer, cpu)))
the full mutex checks enabled with (CONFIG_PROVE_LOCKING) this
will test all possible w/w mutex interface abuse with the
exception of simply not acquiring all the required locks.
+ Note that this feature can introduce significant overhead, so
+ it really should not be enabled in a production or distro kernel,
+ even a debug kernel. If you are a driver writer, enable it. If
+ you are a distro, do not.
config DEBUG_LOCK_ALLOC
bool "Lock debugging: detect incorrect freeing of live locks"
either tracing or lock debugging.
config STACKTRACE
- bool
+ bool "Stack backtrace support"
depends on STACKTRACE_SUPPORT
+ help
+ This option causes the kernel to create a /proc/pid/stack for
+ every process, showing its current stack trace.
+ It is also used by various kernel debugging features that require
+ stack trace generation.
config DEBUG_KOBJECT
bool "kobject debugging"
gc_complete:
edit->set[0].to = new_root;
assoc_array_apply_edit(edit);
- edit->array->nr_leaves_on_tree = nr_leaves_on_tree;
+ array->nr_leaves_on_tree = nr_leaves_on_tree;
return 0;
enomem:
if (hugetlb_cgroup_disabled())
return;
- VM_BUG_ON(!spin_is_locked(&hugetlb_lock));
+ lockdep_assert_held(&hugetlb_lock);
h_cg = hugetlb_cgroup_from_page(page);
if (unlikely(!h_cg))
return;
phys_addr_t align, phys_addr_t start,
phys_addr_t end, int nid)
{
- int ret;
- phys_addr_t kernel_end;
+ phys_addr_t kernel_end, ret;
/* pump up @end */
if (end == MEMBLOCK_ALLOC_ACCESSIBLE)
unsigned long pfn = pte_pfn(pte);
if (HAVE_PTE_SPECIAL) {
- if (likely(!pte_special(pte) || pte_numa(pte)))
+ if (likely(!pte_special(pte)))
goto check_pfn;
if (vma->vm_flags & (VM_PFNMAP | VM_MIXEDMAP))
return NULL;
}
}
+ if (is_zero_pfn(pfn))
+ return NULL;
check_pfn:
if (unlikely(pfn > highest_memmap_pfn)) {
print_bad_pte(vma, addr, pte, NULL);
return NULL;
}
- if (is_zero_pfn(pfn))
- return NULL;
-
/*
* NOTE! We still have PageReserved() pages in the page tables.
* eg. VDSO mappings can cause them to exist.
pmd_t entry = *pmdp;
if (pmd_numa(entry))
entry = pmd_mknonnuma(entry);
- set_pmd_at(vma->vm_mm, address, pmdp, pmd_mknotpresent(*pmdp));
+ set_pmd_at(vma->vm_mm, address, pmdp, pmd_mknotpresent(entry));
flush_tlb_range(vma, address, address + HPAGE_PMD_SIZE);
}
#endif /* CONFIG_TRANSPARENT_HUGEPAGE */
.total_size = zbud_zpool_total_size,
};
+MODULE_ALIAS("zpool-zbud");
#endif /* CONFIG_ZPOOL */
/*****************
driver = zpool_get_driver(type);
if (!driver) {
- request_module(type);
+ request_module("zpool-%s", type);
driver = zpool_get_driver(type);
}
.total_size = zs_zpool_total_size,
};
+MODULE_ALIAS("zpool-zsmalloc");
#endif /* CONFIG_ZPOOL */
/* per-cpu VM mapping areas for zspage accesses that cross page boundaries */
# Check for improperly formed commit descriptions
if ($in_commit_log &&
$line =~ /\bcommit\s+[0-9a-f]{5,}/i &&
- $line !~ /\b[Cc]ommit [0-9a-f]{12,16} \("/) {
+ $line !~ /\b[Cc]ommit [0-9a-f]{12,40} \("/) {
$line =~ /\b(c)ommit\s+([0-9a-f]{5,})/i;
my $init_char = $1;
my $orig_commit = lc($2);
my $desc = 'commit description';
($id, $desc) = git_commit_info($orig_commit, $id, $desc);
ERROR("GIT_COMMIT_ID",
- "Please use 12 to 16 chars for the git commit ID like: '${init_char}ommit $id (\"$desc\")'\n" . $herecurr);
+ "Please use 12 or more chars for the git commit ID like: '${init_char}ommit $id (\"$desc\")'\n" . $herecurr);
}
# Check for added, moved or deleted files
$prototype =~ s/^noinline +//;
$prototype =~ s/__init +//;
$prototype =~ s/__init_or_module +//;
+ $prototype =~ s/__meminit +//;
$prototype =~ s/__must_check +//;
$prototype =~ s/__weak +//;
my $define = $prototype =~ s/^#\s*define\s+//; #ak added
struct rb_root key_user_tree; /* tree of quota records indexed by UID */
DEFINE_SPINLOCK(key_user_lock);
-unsigned int key_quota_root_maxkeys = 200; /* root's key count quota */
-unsigned int key_quota_root_maxbytes = 20000; /* root's key space quota */
+unsigned int key_quota_root_maxkeys = 1000000; /* root's key count quota */
+unsigned int key_quota_root_maxbytes = 25000000; /* root's key space quota */
unsigned int key_quota_maxkeys = 200; /* general key count quota */
unsigned int key_quota_maxbytes = 20000; /* general key space quota */
* Use filesystem name if filesystem does not support rename()
* operation.
*/
- if (!inode->i_op->rename)
+ if (!inode->i_op->rename && !inode->i_op->rename2)
goto prepend_filesystem_name;
}
/* Prepend device name. */
* Get local name for filesystems without rename() operation
* or dentry without vfsmount.
*/
- if (!path->mnt || !inode->i_op->rename)
+ if (!path->mnt ||
+ (!inode->i_op->rename && !inode->i_op->rename2))
pos = tomoyo_get_local_path(path->dentry, buf,
buf_len - 1);
/* Get absolute name for the rest. */
* snd_info_get_line - read one line from the procfs buffer
* @buffer: the procfs buffer
* @line: the buffer to store
- * @len: the max. buffer size - 1
+ * @len: the max. buffer size
*
* Reads one line from the buffer and stores the string.
*
buffer->stop = 1;
if (c == '\n')
break;
- if (len) {
+ if (len > 1) {
len--;
*line++ = c;
}
},
[SNDRV_PCM_FORMAT_DSD_U8] = {
.width = 8, .phys = 8, .le = 1, .signd = 0,
- .silence = {},
+ .silence = { 0x69 },
},
[SNDRV_PCM_FORMAT_DSD_U16_LE] = {
.width = 16, .phys = 16, .le = 1, .signd = 0,
- .silence = {},
+ .silence = { 0x69, 0x69 },
},
/* FIXME: the following three formats are not defined properly yet */
[SNDRV_PCM_FORMAT_MPEG] = {
static void update_pcm_pointers(struct amdtp_stream *s,
struct snd_pcm_substream *pcm,
unsigned int frames)
-{ unsigned int ptr;
+{
+ unsigned int ptr;
+
+ /*
+ * In IEC 61883-6, one data block represents one event. In ALSA, one
+ * event equals to one PCM frame. But Dice has a quirk to transfer
+ * two PCM frames in one data block.
+ */
+ if (s->double_pcm_frames)
+ frames *= 2;
ptr = s->pcm_buffer_pointer + frames;
if (ptr >= pcm->runtime->buffer_size)
unsigned int pcm_buffer_pointer;
unsigned int pcm_period_pointer;
bool pointer_flush;
+ bool double_pcm_frames;
struct snd_rawmidi_substream *midi[AMDTP_MAX_CHANNELS_FOR_MIDI * 8];
return err;
/*
- * At rates above 96 kHz, pretend that the stream runs at half the
- * actual sample rate with twice the number of channels; two samples
- * of a channel are stored consecutively in the packet. Requires
- * blocking mode and PCM buffer size should be aligned to SYT_INTERVAL.
+ * At 176.4/192.0 kHz, Dice has a quirk to transfer two PCM frames in
+ * one data block of AMDTP packet. Thus sampling transfer frequency is
+ * a half of PCM sampling frequency, i.e. PCM frames at 192.0 kHz are
+ * transferred on AMDTP packets at 96 kHz. Two successive samples of a
+ * channel are stored consecutively in the packet. This quirk is called
+ * as 'Dual Wire'.
+ * For this quirk, blocking mode is required and PCM buffer size should
+ * be aligned to SYT_INTERVAL.
*/
channels = params_channels(hw_params);
if (rate_index > 4) {
return err;
}
- for (i = 0; i < channels; i++) {
- dice->stream.pcm_positions[i * 2] = i;
- dice->stream.pcm_positions[i * 2 + 1] = i + channels;
- }
-
rate /= 2;
channels *= 2;
+ dice->stream.double_pcm_frames = true;
+ } else {
+ dice->stream.double_pcm_frames = false;
}
mode = rate_index_to_mode(rate_index);
amdtp_stream_set_parameters(&dice->stream, rate, channels,
dice->rx_midi_ports[mode]);
+ if (rate_index > 4) {
+ channels /= 2;
+
+ for (i = 0; i < channels; i++) {
+ dice->stream.pcm_positions[i] = i * 2;
+ dice->stream.pcm_positions[i + channels] = i * 2 + 1;
+ }
+ }
+
amdtp_stream_set_pcm_format(&dice->stream,
params_format(hw_params));
*/
#ifndef CT20K1REG_H
-#define CT20k1REG_H
+#define CT20K1REG_H
/* 20k1 registers */
#define DSPXRAM_START 0x000000
#define I2SD_R 0x19L
#endif /* CT20K1REG_H */
-
-
*/
#ifndef __CA0132_REGS_H
-#define __CA0312_REGS_H
+#define __CA0132_REGS_H
#define DSP_CHIP_OFFSET 0x100000
#define DSP_DBGCNTL_MODULE_OFFSET 0xE30
CXT_FIXUP_HEADPHONE_MIC_PIN,
CXT_FIXUP_HEADPHONE_MIC,
CXT_FIXUP_GPIO1,
+ CXT_FIXUP_ASPIRE_DMIC,
CXT_FIXUP_THINKPAD_ACPI,
CXT_FIXUP_OLPC_XO,
CXT_FIXUP_CAP_MIX_AMP,
{ }
},
},
+ [CXT_FIXUP_ASPIRE_DMIC] = {
+ .type = HDA_FIXUP_FUNC,
+ .v.func = cxt_fixup_stereo_dmic,
+ .chained = true,
+ .chain_id = CXT_FIXUP_GPIO1,
+ },
[CXT_FIXUP_THINKPAD_ACPI] = {
.type = HDA_FIXUP_FUNC,
.v.func = hda_fixup_thinkpad_acpi,
static const struct snd_pci_quirk cxt5066_fixups[] = {
SND_PCI_QUIRK(0x1025, 0x0543, "Acer Aspire One 522", CXT_FIXUP_STEREO_DMIC),
- SND_PCI_QUIRK(0x1025, 0x054c, "Acer Aspire 3830TG", CXT_FIXUP_GPIO1),
+ SND_PCI_QUIRK(0x1025, 0x054c, "Acer Aspire 3830TG", CXT_FIXUP_ASPIRE_DMIC),
SND_PCI_QUIRK(0x1043, 0x138d, "Asus", CXT_FIXUP_HEADPHONE_MIC_PIN),
SND_PCI_QUIRK(0x152d, 0x0833, "OLPC XO-1.5", CXT_FIXUP_OLPC_XO),
SND_PCI_QUIRK(0x17aa, 0x20f2, "Lenovo T400", CXT_PINCFG_LENOVO_TP410),
case 0x10ec0885:
case 0x10ec0887:
/*case 0x10ec0889:*/ /* this causes an SPDIF problem */
+ case 0x10ec0900:
alc889_coef_init(codec);
break;
case 0x10ec0888:
switch (codec->vendor_id) {
case 0x10ec0882:
case 0x10ec0885:
+ case 0x10ec0900:
break;
default:
/* ALC883 and variants */
ALC292_FIXUP_TPT440_DOCK,
ALC283_FIXUP_BXBT2807_MIC,
ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED,
+ ALC282_FIXUP_ASPIRE_V5_PINS,
};
static const struct hda_fixup alc269_fixups[] = {
.chained_before = true,
.chain_id = ALC255_FIXUP_DELL1_MIC_NO_PRESENCE
},
+ [ALC282_FIXUP_ASPIRE_V5_PINS] = {
+ .type = HDA_FIXUP_PINS,
+ .v.pins = (const struct hda_pintbl[]) {
+ { 0x12, 0x90a60130 },
+ { 0x14, 0x90170110 },
+ { 0x17, 0x40000008 },
+ { 0x18, 0x411111f0 },
+ { 0x19, 0x411111f0 },
+ { 0x1a, 0x411111f0 },
+ { 0x1b, 0x411111f0 },
+ { 0x1d, 0x40f89b2d },
+ { 0x1e, 0x411111f0 },
+ { 0x21, 0x0321101f },
+ { },
+ },
+ },
};
SND_PCI_QUIRK(0x1025, 0x0740, "Acer AO725", ALC271_FIXUP_HP_GATE_MIC_JACK),
SND_PCI_QUIRK(0x1025, 0x0742, "Acer AO756", ALC271_FIXUP_HP_GATE_MIC_JACK),
SND_PCI_QUIRK(0x1025, 0x0775, "Acer Aspire E1-572", ALC271_FIXUP_HP_GATE_MIC_JACK_E1_572),
+ SND_PCI_QUIRK(0x1025, 0x079b, "Acer Aspire V5-573G", ALC282_FIXUP_ASPIRE_V5_PINS),
SND_PCI_QUIRK(0x1028, 0x0470, "Dell M101z", ALC269_FIXUP_DELL_M101Z),
SND_PCI_QUIRK(0x1028, 0x05bd, "Dell", ALC269_FIXUP_DELL2_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x05be, "Dell", ALC269_FIXUP_DELL2_MIC_NO_PRESENCE),
/*64k*/
{8192000, 64000, 1, 0},
- {1228800, 64000, 1, 1},
- {1693440, 64000, 1, 2},
- {2457600, 64000, 1, 3},
- {3276800, 64000, 1, 4},
+ {12288000, 64000, 1, 1},
+ {16934400, 64000, 1, 2},
+ {24576000, 64000, 1, 3},
+ {32768000, 64000, 1, 4},
/* 88.2k */
{11289600, 88200, 1, 0},
index = cs4265_get_clk_index(cs4265->sysclk, params_rate(params));
if (index >= 0) {
snd_soc_update_bits(codec, CS4265_ADC_CTL,
- CS4265_ADC_FM, clk_map_table[index].fm_mode);
+ CS4265_ADC_FM, clk_map_table[index].fm_mode << 6);
snd_soc_update_bits(codec, CS4265_MCLK_FREQ,
CS4265_MCLK_FREQ_MASK,
- clk_map_table[index].mclkdiv);
+ clk_map_table[index].mclkdiv << 4);
} else {
dev_err(codec->dev, "can't get correct mclk\n");
*/
#ifndef __DA732X_H_
-#define __DA732X_H
+#define __DA732X_H_
#include <sound/soc.h>
static const struct regmap_config rt5640_regmap = {
.reg_bits = 8,
.val_bits = 16,
+ .use_single_rw = true,
.max_register = RT5640_VENDOR_ID2 + 1 + (ARRAY_SIZE(rt5640_ranges) *
RT5640_PR_SPACING),
{ "BST2", NULL, "IN2P" },
{ "BST2", NULL, "IN2N" },
- { "IN1P", NULL, "micbias1" },
- { "IN1N", NULL, "micbias1" },
- { "IN2P", NULL, "micbias1" },
- { "IN2N", NULL, "micbias1" },
+ { "IN1P", NULL, "MICBIAS1" },
+ { "IN1N", NULL, "MICBIAS1" },
+ { "IN2P", NULL, "MICBIAS1" },
+ { "IN2N", NULL, "MICBIAS1" },
{ "ADC 1", NULL, "BST1" },
{ "ADC 1", NULL, "ADC 1 power" },
snd_soc_card_set_drvdata(&priv->snd_card, priv);
ret = devm_snd_soc_register_card(&pdev->dev, &priv->snd_card);
+ if (ret >= 0)
+ return ret;
err:
asoc_simple_card_unref(pdev);
return ret;
}
+static int asoc_simple_card_remove(struct platform_device *pdev)
+{
+ return asoc_simple_card_unref(pdev);
+}
+
static const struct of_device_id asoc_simple_of_match[] = {
{ .compatible = "simple-audio-card", },
{},
.of_match_table = asoc_simple_of_match,
},
.probe = asoc_simple_card_probe,
+ .remove = asoc_simple_card_remove,
};
module_platform_driver(asoc_simple_card);
.stream_name = "TWL4030 Voice",
.cpu_dai_name = "omap-mcbsp.3",
.codec_dai_name = "twl4030-voice",
- .platform_name = "omap-mcbsp.2",
+ .platform_name = "omap-mcbsp.3",
.codec_name = "twl4030-codec",
.dai_fmt = SND_SOC_DAIFMT_DSP_A | SND_SOC_DAIFMT_IB_NF |
SND_SOC_DAIFMT_CBM_CFM,
};
/* it shouldn't happen */
- if (use_dvc & !use_src)
+ if (use_dvc && !use_src)
dev_err(dev, "DVC is selected without SRC\n");
/* use SSIU or SSI ? */
device_initialize(rtd->dev);
rtd->dev->parent = rtd->card->dev;
rtd->dev->release = rtd_release;
- rtd->dev->init_name = name;
+ dev_set_name(rtd->dev, "%s", name);
dev_set_drvdata(rtd->dev, rtd);
mutex_init(&rtd->pcm_mutex);
INIT_LIST_HEAD(&rtd->dpcm[SNDRV_PCM_STREAM_PLAYBACK].be_clients);
*/
#ifndef __TEGRA_ASOC_UTILS_H__
-#define __TEGRA_ASOC_UTILS_H_
+#define __TEGRA_ASOC_UTILS_H__
struct clk;
struct device;
uname_M := $(shell uname -m 2>/dev/null || echo not)
ARCH ?= $(shell echo $(uname_M) | sed -e s/i.86/i386/)
ifeq ($(ARCH),i386)
- ARCH := X86
+ ARCH := x86
CFLAGS := -DCONFIG_X86_32 -D__i386__
endif
ifeq ($(ARCH),x86_64)
- ARCH := X86
+ ARCH := x86
CFLAGS := -DCONFIG_X86_64 -D__x86_64__
endif
CFLAGS += -I../../../../usr/include/
all:
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) msgque.c -o msgque_test
else
echo "Not an x86 target, can't build msgque selftest"
uname_M := $(shell uname -m 2>/dev/null || echo not)
ARCH ?= $(shell echo $(uname_M) | sed -e s/i.86/i386/)
ifeq ($(ARCH),i386)
- ARCH := X86
+ ARCH := x86
CFLAGS := -DCONFIG_X86_32 -D__i386__
endif
ifeq ($(ARCH),x86_64)
- ARCH := X86
+ ARCH := x86
CFLAGS := -DCONFIG_X86_64 -D__x86_64__
endif
CFLAGS += -I../../../../arch/x86/include/
all:
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) kcmp_test.c -o kcmp_test
else
echo "Not an x86 target, can't build kcmp selftest"
uname_M := $(shell uname -m 2>/dev/null || echo not)
ARCH ?= $(shell echo $(uname_M) | sed -e s/i.86/i386/)
ifeq ($(ARCH),i386)
- ARCH := X86
+ ARCH := x86
endif
ifeq ($(ARCH),x86_64)
- ARCH := X86
+ ARCH := x86
endif
CFLAGS += -D_FILE_OFFSET_BITS=64
CFLAGS += -I../../../../include/
all:
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) memfd_test.c -o memfd_test
else
echo "Not an x86 target, can't build memfd selftest"
endif
run_tests: all
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) memfd_test.c -o memfd_test
endif
@./memfd_test || echo "memfd_test: [FAIL]"
build_fuse:
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) fuse_mnt.c `pkg-config fuse --cflags --libs` -o fuse_mnt
gcc $(CFLAGS) fuse_test.c -o fuse_test
else