of support for RGMII internal delays (supported on P/Q/R/S, but not on
E/T).
-Optional properties:
-
-- sja1105,role-mac:
-- sja1105,role-phy:
- Boolean properties that can be assigned under each port node. By
- default (unless otherwise specified) a port is configured as MAC if it
- is driving a PHY (phy-handle is present) or as PHY if it is PHY-less
- (fixed-link specified, presumably because it is connected to a MAC).
- The effect of this property (in either its implicit or explicit form)
- is:
- - In the case of MII or RMII it specifies whether the SJA1105 port is a
- clock source or sink for this interface (not applicable for RGMII
- where there is a Tx and an Rx clock).
- - In the case of RGMII it affects the behavior regarding internal
- delays:
- 1. If sja1105,role-mac is specified, and the phy-mode property is one
- of "rgmii-id", "rgmii-txid" or "rgmii-rxid", then the entity
- designated to apply the delay/clock skew necessary for RGMII
- is the PHY. The SJA1105 MAC does not apply any internal delays.
- 2. If sja1105,role-phy is specified, and the phy-mode property is one
- of the above, the designated entity to apply the internal delays
- is the SJA1105 MAC (if hardware-supported). This is only supported
- by the second-generation (P/Q/R/S) hardware. On a first-generation
- E or T device, it is an error to specify an RGMII phy-mode other
- than "rgmii" for a port that is in fixed-link mode. In that case,
- the clock skew must either be added by the MAC at the other end of
- the fixed-link, or by PCB serpentine traces on the board.
- These properties are required, for example, in the case where SJA1105
- ports are at both ends of a MII/RMII PHY-less setup. One end would need
- to have sja1105,role-mac, while the other sja1105,role-phy.
-
See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard
DSA required and optional properties.
phy-handle = <&rgmii_phy6>;
phy-mode = "rgmii-id";
reg = <0>;
- /* Implicit "sja1105,role-mac;" */
};
port@1 {
/* ETH2 written on chassis */
phy-handle = <&rgmii_phy3>;
phy-mode = "rgmii-id";
reg = <1>;
- /* Implicit "sja1105,role-mac;" */
};
port@2 {
/* ETH3 written on chassis */
phy-handle = <&rgmii_phy4>;
phy-mode = "rgmii-id";
reg = <2>;
- /* Implicit "sja1105,role-mac;" */
};
port@3 {
/* ETH4 written on chassis */
label = "swp4";
phy-mode = "rgmii-id";
reg = <3>;
- /* Implicit "sja1105,role-mac;" */
};
port@4 {
/* Internal port connected to eth2 */
ethernet = <&enet2>;
phy-mode = "rgmii";
reg = <4>;
- /* Implicit "sja1105,role-phy;" */
+
fixed-link {
speed = <1000>;
full-duplex;
return !!(l2_fwd[from].reach_port & BIT(to));
}
-/* Structure used to temporarily transport device tree
- * settings into sja1105_setup
- */
-struct sja1105_dt_port {
- phy_interface_t phy_mode;
- sja1105_mii_role_t role;
-};
-
static int sja1105_init_mac_settings(struct sja1105_private *priv)
{
struct sja1105_mac_config_entry default_mac = {
return 0;
}
-static int sja1105_init_mii_settings(struct sja1105_private *priv,
- struct sja1105_dt_port *ports)
+static int sja1105_init_mii_settings(struct sja1105_private *priv)
{
struct device *dev = &priv->spidev->dev;
struct sja1105_xmii_params_entry *mii;
mii = table->entries;
for (i = 0; i < ds->num_ports; i++) {
+ sja1105_mii_role_t role = XMII_MAC;
+
if (dsa_is_unused_port(priv->ds, i))
continue;
- switch (ports[i].phy_mode) {
+ switch (priv->phy_mode[i]) {
+ case PHY_INTERFACE_MODE_REVMII:
+ role = XMII_PHY;
+ fallthrough;
case PHY_INTERFACE_MODE_MII:
if (!priv->info->supports_mii[i])
goto unsupported;
mii->xmii_mode[i] = XMII_MODE_MII;
break;
+ case PHY_INTERFACE_MODE_REVRMII:
+ role = XMII_PHY;
+ fallthrough;
case PHY_INTERFACE_MODE_RMII:
if (!priv->info->supports_rmii[i])
goto unsupported;
unsupported:
default:
dev_err(dev, "Unsupported PHY mode %s on port %d!\n",
- phy_modes(ports[i].phy_mode), i);
+ phy_modes(priv->phy_mode[i]), i);
return -EINVAL;
}
- /* Even though the SerDes port is able to drive SGMII autoneg
- * like a PHY would, from the perspective of the XMII tables,
- * the SGMII port should always be put in MAC mode.
- * Similarly, RGMII is a symmetric protocol electrically
- * speaking, and the 'RGMII PHY' role does not mean anything to
- * hardware. Just keep the 'PHY role' notation relevant to the
- * driver to mean 'the switch port should apply RGMII delays',
- * but unconditionally put the port in the MAC role.
- */
- if (ports[i].phy_mode == PHY_INTERFACE_MODE_SGMII ||
- phy_interface_mode_is_rgmii(ports[i].phy_mode))
- mii->phy_mac[i] = XMII_MAC;
- else
- mii->phy_mac[i] = ports[i].role;
+ mii->phy_mac[i] = role;
}
return 0;
}
return 0;
}
-static int sja1105_static_config_load(struct sja1105_private *priv,
- struct sja1105_dt_port *ports)
+static int sja1105_static_config_load(struct sja1105_private *priv)
{
int rc;
rc = sja1105_init_mac_settings(priv);
if (rc < 0)
return rc;
- rc = sja1105_init_mii_settings(priv, ports);
+ rc = sja1105_init_mii_settings(priv);
if (rc < 0)
return rc;
rc = sja1105_init_static_fdb(priv);
}
static int sja1105_parse_ports_node(struct sja1105_private *priv,
- struct sja1105_dt_port *ports,
struct device_node *ports_node)
{
struct device *dev = &priv->spidev->dev;
of_node_put(child);
return -ENODEV;
}
- ports[index].phy_mode = phy_mode;
phy_node = of_parse_phandle(child, "phy-handle", 0);
if (!phy_node) {
* So it's a fixed link. Default to PHY role.
*/
priv->fixed_link[index] = true;
- ports[index].role = XMII_PHY;
} else {
- /* phy-handle present => put port in MAC role */
- ports[index].role = XMII_MAC;
of_node_put(phy_node);
}
- /* The MAC/PHY role can be overridden with explicit bindings */
- if (of_property_read_bool(child, "sja1105,role-mac"))
- ports[index].role = XMII_MAC;
- else if (of_property_read_bool(child, "sja1105,role-phy"))
- ports[index].role = XMII_PHY;
-
priv->phy_mode[index] = phy_mode;
}
return 0;
}
-static int sja1105_parse_dt(struct sja1105_private *priv,
- struct sja1105_dt_port *ports)
+static int sja1105_parse_dt(struct sja1105_private *priv)
{
struct device *dev = &priv->spidev->dev;
struct device_node *switch_node = dev->of_node;
return -ENODEV;
}
- rc = sja1105_parse_ports_node(priv, ports, ports_node);
+ rc = sja1105_parse_ports_node(priv, ports_node);
of_node_put(ports_node);
return rc;
*/
static int sja1105_setup(struct dsa_switch *ds)
{
- struct sja1105_dt_port ports[SJA1105_MAX_NUM_PORTS];
struct sja1105_private *priv = ds->priv;
int rc;
- rc = sja1105_parse_dt(priv, ports);
+ rc = sja1105_parse_dt(priv);
if (rc < 0) {
dev_err(ds->dev, "Failed to parse DT: %d\n", rc);
return rc;
return rc;
}
/* Create and send configuration down to device */
- rc = sja1105_static_config_load(priv, ports);
+ rc = sja1105_static_config_load(priv);
if (rc < 0) {
dev_err(ds->dev, "Failed to load static config: %d\n", rc);
goto out_ptp_clock_unregister;
projects / platform / kernel / linux-starfive.git / commitdiff