#include <linux/of_device.h>
#include <linux/of_platform.h>
+#include <linux/of_mdio.h>
+#include <linux/phy.h>
#define DRIVER_NAME "xilinx_emaclite"
/* Register offsets for the EmacLite Core */
#define XEL_TXBUFF_OFFSET 0x0 /* Transmit Buffer */
+#define XEL_MDIOADDR_OFFSET 0x07E4 /* MDIO Address Register */
+#define XEL_MDIOWR_OFFSET 0x07E8 /* MDIO Write Data Register */
+#define XEL_MDIORD_OFFSET 0x07EC /* MDIO Read Data Register */
+#define XEL_MDIOCTRL_OFFSET 0x07F0 /* MDIO Control Register */
#define XEL_GIER_OFFSET 0x07F8 /* GIE Register */
#define XEL_TSR_OFFSET 0x07FC /* Tx status */
#define XEL_TPLR_OFFSET 0x07F4 /* Tx packet length */
#define XEL_BUFFER_OFFSET 0x0800 /* Next Tx/Rx buffer's offset */
+/* MDIO Address Register Bit Masks */
+#define XEL_MDIOADDR_REGADR_MASK 0x0000001F /* Register Address */
+#define XEL_MDIOADDR_PHYADR_MASK 0x000003E0 /* PHY Address */
+#define XEL_MDIOADDR_PHYADR_SHIFT 5
+#define XEL_MDIOADDR_OP_MASK 0x00000400 /* RD/WR Operation */
+
+/* MDIO Write Data Register Bit Masks */
+#define XEL_MDIOWR_WRDATA_MASK 0x0000FFFF /* Data to be Written */
+
+/* MDIO Read Data Register Bit Masks */
+#define XEL_MDIORD_RDDATA_MASK 0x0000FFFF /* Data to be Read */
+
+/* MDIO Control Register Bit Masks */
+#define XEL_MDIOCTRL_MDIOSTS_MASK 0x00000001 /* MDIO Status Mask */
+#define XEL_MDIOCTRL_MDIOEN_MASK 0x00000008 /* MDIO Enable */
+
/* Global Interrupt Enable Register (GIER) Bit Masks */
#define XEL_GIER_GIE_MASK 0x80000000 /* Global Enable */
* @reset_lock: lock used for synchronization
* @deferred_skb: holds an skb (for transmission at a later time) when the
* Tx buffer is not free
+ * @phy_dev: pointer to the PHY device
+ * @phy_node: pointer to the PHY device node
+ * @mii_bus: pointer to the MII bus
+ * @mdio_irqs: IRQs table for MDIO bus
+ * @last_link: last link status
+ * @has_mdio: indicates whether MDIO is included in the HW
*/
struct net_local {
spinlock_t reset_lock;
struct sk_buff *deferred_skb;
+
+ struct phy_device *phy_dev;
+ struct device_node *phy_node;
+
+ struct mii_bus *mii_bus;
+ int mdio_irqs[PHY_MAX_ADDR];
+
+ int last_link;
+ bool has_mdio;
};
}
/**
- * xemaclite_set_mac_address - Set the MAC address for this device
+ * xemaclite_update_address - Update the MAC address in the device
* @drvdata: Pointer to the Emaclite device private data
* @address_ptr:Pointer to the MAC address (MAC address is a 48-bit value)
*
* The MAC address can be programmed using any of the two transmit
* buffers (if configured).
*/
-static void xemaclite_set_mac_address(struct net_local *drvdata,
- u8 *address_ptr)
+static void xemaclite_update_address(struct net_local *drvdata,
+ u8 *address_ptr)
{
void __iomem *addr;
u32 reg_data;
}
/**
+ * xemaclite_set_mac_address - Set the MAC address for this device
+ * @dev: Pointer to the network device instance
+ * @addr: Void pointer to the sockaddr structure
+ *
+ * This function copies the HW address from the sockaddr strucutre to the
+ * net_device structure and updates the address in HW.
+ *
+ * Return: Error if the net device is busy or 0 if the addr is set
+ * successfully
+ */
+static int xemaclite_set_mac_address(struct net_device *dev, void *address)
+{
+ struct net_local *lp = (struct net_local *) netdev_priv(dev);
+ struct sockaddr *addr = address;
+
+ if (netif_running(dev))
+ return -EBUSY;
+
+ memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
+ xemaclite_update_address(lp, dev->dev_addr);
+ return 0;
+}
+
+/**
* xemaclite_tx_timeout - Callback for Tx Timeout
* @dev: Pointer to the network device
*
return IRQ_HANDLED;
}
+/**********************/
+/* MDIO Bus functions */
+/**********************/
+
+/**
+ * xemaclite_mdio_wait - Wait for the MDIO to be ready to use
+ * @lp: Pointer to the Emaclite device private data
+ *
+ * This function waits till the device is ready to accept a new MDIO
+ * request.
+ *
+ * Return: 0 for success or ETIMEDOUT for a timeout
+ */
+
+static int xemaclite_mdio_wait(struct net_local *lp)
+{
+ long end = jiffies + 2;
+
+ /* wait for the MDIO interface to not be busy or timeout
+ after some time.
+ */
+ while (in_be32(lp->base_addr + XEL_MDIOCTRL_OFFSET) &
+ XEL_MDIOCTRL_MDIOSTS_MASK) {
+ if (end - jiffies <= 0) {
+ WARN_ON(1);
+ return -ETIMEDOUT;
+ }
+ msleep(1);
+ }
+ return 0;
+}
+
+/**
+ * xemaclite_mdio_read - Read from a given MII management register
+ * @bus: the mii_bus struct
+ * @phy_id: the phy address
+ * @reg: register number to read from
+ *
+ * This function waits till the device is ready to accept a new MDIO
+ * request and then writes the phy address to the MDIO Address register
+ * and reads data from MDIO Read Data register, when its available.
+ *
+ * Return: Value read from the MII management register
+ */
+static int xemaclite_mdio_read(struct mii_bus *bus, int phy_id, int reg)
+{
+ struct net_local *lp = bus->priv;
+ u32 ctrl_reg;
+ u32 rc;
+
+ if (xemaclite_mdio_wait(lp))
+ return -ETIMEDOUT;
+
+ /* Write the PHY address, register number and set the OP bit in the
+ * MDIO Address register. Set the Status bit in the MDIO Control
+ * register to start a MDIO read transaction.
+ */
+ ctrl_reg = in_be32(lp->base_addr + XEL_MDIOCTRL_OFFSET);
+ out_be32(lp->base_addr + XEL_MDIOADDR_OFFSET,
+ XEL_MDIOADDR_OP_MASK |
+ ((phy_id << XEL_MDIOADDR_PHYADR_SHIFT) | reg));
+ out_be32(lp->base_addr + XEL_MDIOCTRL_OFFSET,
+ ctrl_reg | XEL_MDIOCTRL_MDIOSTS_MASK);
+
+ if (xemaclite_mdio_wait(lp))
+ return -ETIMEDOUT;
+
+ rc = in_be32(lp->base_addr + XEL_MDIORD_OFFSET);
+
+ dev_dbg(&lp->ndev->dev,
+ "xemaclite_mdio_read(phy_id=%i, reg=%x) == %x\n",
+ phy_id, reg, rc);
+
+ return rc;
+}
+
+/**
+ * xemaclite_mdio_write - Write to a given MII management register
+ * @bus: the mii_bus struct
+ * @phy_id: the phy address
+ * @reg: register number to write to
+ * @val: value to write to the register number specified by reg
+ *
+ * This fucntion waits till the device is ready to accept a new MDIO
+ * request and then writes the val to the MDIO Write Data register.
+ */
+static int xemaclite_mdio_write(struct mii_bus *bus, int phy_id, int reg,
+ u16 val)
+{
+ struct net_local *lp = bus->priv;
+ u32 ctrl_reg;
+
+ dev_dbg(&lp->ndev->dev,
+ "xemaclite_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
+ phy_id, reg, val);
+
+ if (xemaclite_mdio_wait(lp))
+ return -ETIMEDOUT;
+
+ /* Write the PHY address, register number and clear the OP bit in the
+ * MDIO Address register and then write the value into the MDIO Write
+ * Data register. Finally, set the Status bit in the MDIO Control
+ * register to start a MDIO write transaction.
+ */
+ ctrl_reg = in_be32(lp->base_addr + XEL_MDIOCTRL_OFFSET);
+ out_be32(lp->base_addr + XEL_MDIOADDR_OFFSET,
+ ~XEL_MDIOADDR_OP_MASK &
+ ((phy_id << XEL_MDIOADDR_PHYADR_SHIFT) | reg));
+ out_be32(lp->base_addr + XEL_MDIOWR_OFFSET, val);
+ out_be32(lp->base_addr + XEL_MDIOCTRL_OFFSET,
+ ctrl_reg | XEL_MDIOCTRL_MDIOSTS_MASK);
+
+ return 0;
+}
+
+/**
+ * xemaclite_mdio_reset - Reset the mdio bus.
+ * @bus: Pointer to the MII bus
+ *
+ * This function is required(?) as per Documentation/networking/phy.txt.
+ * There is no reset in this device; this function always returns 0.
+ */
+static int xemaclite_mdio_reset(struct mii_bus *bus)
+{
+ return 0;
+}
+
+/**
+ * xemaclite_mdio_setup - Register mii_bus for the Emaclite device
+ * @lp: Pointer to the Emaclite device private data
+ * @ofdev: Pointer to OF device structure
+ *
+ * This function enables MDIO bus in the Emaclite device and registers a
+ * mii_bus.
+ *
+ * Return: 0 upon success or a negative error upon failure
+ */
+static int xemaclite_mdio_setup(struct net_local *lp, struct device *dev)
+{
+ struct mii_bus *bus;
+ int rc;
+ struct resource res;
+ struct device_node *np = of_get_parent(lp->phy_node);
+
+ /* Don't register the MDIO bus if the phy_node or its parent node
+ * can't be found.
+ */
+ if (!np)
+ return -ENODEV;
+
+ /* Enable the MDIO bus by asserting the enable bit in MDIO Control
+ * register.
+ */
+ out_be32(lp->base_addr + XEL_MDIOCTRL_OFFSET,
+ XEL_MDIOCTRL_MDIOEN_MASK);
+
+ bus = mdiobus_alloc();
+ if (!bus)
+ return -ENOMEM;
+
+ of_address_to_resource(np, 0, &res);
+ snprintf(bus->id, MII_BUS_ID_SIZE, "%.8llx",
+ (unsigned long long)res.start);
+ bus->priv = lp;
+ bus->name = "Xilinx Emaclite MDIO";
+ bus->read = xemaclite_mdio_read;
+ bus->write = xemaclite_mdio_write;
+ bus->reset = xemaclite_mdio_reset;
+ bus->parent = dev;
+ bus->irq = lp->mdio_irqs; /* preallocated IRQ table */
+
+ lp->mii_bus = bus;
+
+ rc = of_mdiobus_register(bus, np);
+ if (rc)
+ goto err_register;
+
+ return 0;
+
+err_register:
+ mdiobus_free(bus);
+ return rc;
+}
+
+/**
+ * xemaclite_adjust_link - Link state callback for the Emaclite device
+ * @ndev: pointer to net_device struct
+ *
+ * There's nothing in the Emaclite device to be configured when the link
+ * state changes. We just print the status.
+ */
+void xemaclite_adjust_link(struct net_device *ndev)
+{
+ struct net_local *lp = netdev_priv(ndev);
+ struct phy_device *phy = lp->phy_dev;
+ int link_state;
+
+ /* hash together the state values to decide if something has changed */
+ link_state = phy->speed | (phy->duplex << 1) | phy->link;
+
+ if (lp->last_link != link_state) {
+ lp->last_link = link_state;
+ phy_print_status(phy);
+ }
+}
+
/**
* xemaclite_open - Open the network device
* @dev: Pointer to the network device
*
* This function sets the MAC address, requests an IRQ and enables interrupts
* for the Emaclite device and starts the Tx queue.
+ * It also connects to the phy device, if MDIO is included in Emaclite device.
*/
static int xemaclite_open(struct net_device *dev)
{
/* Just to be safe, stop the device first */
xemaclite_disable_interrupts(lp);
+ if (lp->phy_node) {
+ u32 bmcr;
+
+ lp->phy_dev = of_phy_connect(lp->ndev, lp->phy_node,
+ xemaclite_adjust_link, 0,
+ PHY_INTERFACE_MODE_MII);
+ if (!lp->phy_dev) {
+ dev_err(&lp->ndev->dev, "of_phy_connect() failed\n");
+ return -ENODEV;
+ }
+
+ /* EmacLite doesn't support giga-bit speeds */
+ lp->phy_dev->supported &= (PHY_BASIC_FEATURES);
+ lp->phy_dev->advertising = lp->phy_dev->supported;
+
+ /* Don't advertise 1000BASE-T Full/Half duplex speeds */
+ phy_write(lp->phy_dev, MII_CTRL1000, 0);
+
+ /* Advertise only 10 and 100mbps full/half duplex speeds */
+ phy_write(lp->phy_dev, MII_ADVERTISE, ADVERTISE_ALL);
+
+ /* Restart auto negotiation */
+ bmcr = phy_read(lp->phy_dev, MII_BMCR);
+ bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
+ phy_write(lp->phy_dev, MII_BMCR, bmcr);
+
+ phy_start(lp->phy_dev);
+ }
+
/* Set the MAC address each time opened */
- xemaclite_set_mac_address(lp, dev->dev_addr);
+ xemaclite_update_address(lp, dev->dev_addr);
/* Grab the IRQ */
retval = request_irq(dev->irq, xemaclite_interrupt, 0, dev->name, dev);
if (retval) {
dev_err(&lp->ndev->dev, "Could not allocate interrupt %d\n",
dev->irq);
+ if (lp->phy_dev)
+ phy_disconnect(lp->phy_dev);
+ lp->phy_dev = NULL;
+
return retval;
}
*
* This function stops the Tx queue, disables interrupts and frees the IRQ for
* the Emaclite device.
+ * It also disconnects the phy device associated with the Emaclite device.
*/
static int xemaclite_close(struct net_device *dev)
{
xemaclite_disable_interrupts(lp);
free_irq(dev->irq, dev);
+ if (lp->phy_dev)
+ phy_disconnect(lp->phy_dev);
+ lp->phy_dev = NULL;
+
return 0;
}
}
/**
- * xemaclite_ioctl - Perform IO Control operations on the network device
- * @dev: Pointer to the network device
- * @rq: Pointer to the interface request structure
- * @cmd: IOCTL command
- *
- * The only IOCTL operation supported by this function is setting the MAC
- * address. An error is reported if any other operations are requested.
- *
- * Return: 0 to indicate success, or a negative error for failure.
- */
-static int xemaclite_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-{
- struct net_local *lp = (struct net_local *) netdev_priv(dev);
- struct hw_addr_data *hw_addr = (struct hw_addr_data *) &rq->ifr_hwaddr;
-
- switch (cmd) {
- case SIOCETHTOOL:
- return -EIO;
-
- case SIOCSIFHWADDR:
- dev_err(&lp->ndev->dev, "SIOCSIFHWADDR\n");
-
- /* Copy MAC address in from user space */
- copy_from_user((void __force *) dev->dev_addr,
- (void __user __force *) hw_addr,
- IFHWADDRLEN);
- xemaclite_set_mac_address(lp, dev->dev_addr);
- break;
- default:
- return -EOPNOTSUPP;
- }
-
- return 0;
-}
-
-/**
* xemaclite_remove_ndev - Free the network device
* @ndev: Pointer to the network device to be freed
*
* This function probes for the Emaclite device in the device tree.
* It initializes the driver data structure and the hardware, sets the MAC
* address and registers the network device.
+ * It also registers a mii_bus for the Emaclite device, if MDIO is included
+ * in the device.
*
* Return: 0, if the driver is bound to the Emaclite device, or
* a negative error if there is failure.
}
dev_set_drvdata(dev, ndev);
+ SET_NETDEV_DEV(ndev, &ofdev->dev);
ndev->irq = r_irq.start;
ndev->mem_start = r_mem.start;
out_be32(lp->base_addr + XEL_BUFFER_OFFSET + XEL_TSR_OFFSET, 0);
/* Set the MAC address in the EmacLite device */
- xemaclite_set_mac_address(lp, ndev->dev_addr);
+ xemaclite_update_address(lp, ndev->dev_addr);
+
+ lp->phy_node = of_parse_phandle(ofdev->node, "phy-handle", 0);
+ rc = xemaclite_mdio_setup(lp, &ofdev->dev);
+ if (rc)
+ dev_warn(&ofdev->dev, "error registering MDIO bus\n");
dev_info(dev, "MAC address is now %pM\n", ndev->dev_addr);
struct device *dev = &of_dev->dev;
struct net_device *ndev = dev_get_drvdata(dev);
+ struct net_local *lp = (struct net_local *) netdev_priv(ndev);
+
+ /* Un-register the mii_bus, if configured */
+ if (lp->has_mdio) {
+ mdiobus_unregister(lp->mii_bus);
+ kfree(lp->mii_bus->irq);
+ mdiobus_free(lp->mii_bus);
+ lp->mii_bus = NULL;
+ }
+
unregister_netdev(ndev);
+ if (lp->phy_node)
+ of_node_put(lp->phy_node);
+ lp->phy_node = NULL;
+
release_mem_region(ndev->mem_start, ndev->mem_end-ndev->mem_start + 1);
xemaclite_remove_ndev(ndev);
-
dev_set_drvdata(dev, NULL);
return 0;
.ndo_open = xemaclite_open,
.ndo_stop = xemaclite_close,
.ndo_start_xmit = xemaclite_send,
- .ndo_do_ioctl = xemaclite_ioctl,
+ .ndo_set_mac_address = xemaclite_set_mac_address,
.ndo_tx_timeout = xemaclite_tx_timeout,
.ndo_get_stats = xemaclite_get_stats,
};
{ .compatible = "xlnx,xps-ethernetlite-1.00.a", },
{ .compatible = "xlnx,xps-ethernetlite-2.00.a", },
{ .compatible = "xlnx,xps-ethernetlite-2.01.a", },
+ { .compatible = "xlnx,xps-ethernetlite-3.00.a", },
{ /* end of list */ },
};
MODULE_DEVICE_TABLE(of, xemaclite_of_match);
projects / platform / upstream / kernel-adaptation-pc.git / commitdiff