spi: atmel: Configure GPIO per CS instead of by controller

Instead of setting up the GPIO configuration for the whole controller,
do it at CS level. It will allow to mix internal CS and GPIO CS, which
is not possible with the current implementation.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-4-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 6e08ae5..b511df6 100644 (file)
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -275,7 +275,6 @@ struct atmel_spi {
 
        bool                    use_dma;
        bool                    use_pdc;
-       bool                    use_cs_gpios;
 
        bool                    keep_cs;
        bool                    cs_active;
@@ -348,7 +347,7 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
                }
 
                mr = spi_readl(as, MR);
-               if (as->use_cs_gpios)
+               if (asd->npcs_pin)
                        gpiod_set_value(asd->npcs_pin, 1);
        } else {
                u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
@@ -365,7 +364,7 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
 
                mr = spi_readl(as, MR);
                mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
-               if (as->use_cs_gpios && spi->chip_select != 0)
+               if (asd->npcs_pin && spi->chip_select != 0)
                        gpiod_set_value(asd->npcs_pin, 1);
                spi_writel(as, MR, mr);
        }
@@ -389,7 +388,7 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
 
        dev_dbg(&spi->dev, "DEactivate NPCS, mr %08x\n", mr);
 
-       if (!as->use_cs_gpios)
+       if (!asd->npcs_pin)
                spi_writel(as, CR, SPI_BIT(LASTXFER));
        else if (atmel_spi_is_v2(as) || spi->chip_select != 0)
                gpiod_set_value(asd->npcs_pin, 0);
@@ -1176,7 +1175,7 @@ static int atmel_spi_setup(struct spi_device *spi)
        as = spi_master_get_devdata(spi->master);
 
        /* see notes above re chipselect */
-       if (!as->use_cs_gpios && (spi->mode & SPI_CS_HIGH)) {
+       if (!spi->cs_gpiod && (spi->mode & SPI_CS_HIGH)) {
                dev_warn(&spi->dev, "setup: non GPIO CS can't be active-high\n");
                return -EINVAL;
        }
@@ -1186,9 +1185,9 @@ static int atmel_spi_setup(struct spi_device *spi)
                csr |= SPI_BIT(CPOL);
        if (!(spi->mode & SPI_CPHA))
                csr |= SPI_BIT(NCPHA);
-       if (!as->use_cs_gpios)
-               csr |= SPI_BIT(CSAAT);
 
+       if (!spi->cs_gpiod)
+               csr |= SPI_BIT(CSAAT);
        csr |= SPI_BF(DLYBS, 0);
 
        word_delay_csr = atmel_word_delay_csr(spi, as);
@@ -1206,20 +1205,8 @@ static int atmel_spi_setup(struct spi_device *spi)
                if (!asd)
                        return -ENOMEM;
 
-               /*
-                * If use_cs_gpios is true this means that we have "cs-gpios"
-                * defined in the device tree node so we should have
-                * gotten the GPIO lines from the device tree inside the
-                * SPI core. Warn if this is not the case but continue since
-                * CS GPIOs are after all optional.
-                */
-               if (as->use_cs_gpios) {
-                       if (!spi->cs_gpiod) {
-                               dev_err(&spi->dev,
-                                       "host claims to use CS GPIOs but no CS found in DT by the SPI core\n");
-                       }
+               if (spi->cs_gpiod)
                        asd->npcs_pin = spi->cs_gpiod;
-               }
 
                spi->controller_state = asd;
        }
@@ -1551,13 +1538,10 @@ static int atmel_spi_probe(struct platform_device *pdev)
         * discovered by the SPI core when registering the SPI master
         * and assigned to each SPI device.
         */
-       as->use_cs_gpios = true;
        if (atmel_spi_is_v2(as) &&
            pdev->dev.of_node &&
-           !of_get_property(pdev->dev.of_node, "cs-gpios", NULL)) {
-               as->use_cs_gpios = false;
+           !of_get_property(pdev->dev.of_node, "cs-gpios", NULL))
                master->num_chipselect = 4;
-       }
 
        as->use_dma = false;
        as->use_pdc = false;