net: phy: Add dts support for Motorcomm yt8531s gigabit ethernet phy

Add dts support for Motorcomm yt8531s gigabit ethernet phy.
 Change yt8521_probe to support clk config of yt8531s. Becase
 yt8521_probe does the things which yt8531s is needed, so
 removed yt8531s function.
 This patch has been verified on AM335x platform with yt8531s board.

Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Change-Id: I85e5655baba7120eadad1e25c4da1797c9943154

diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index ee30e8a..bdc6a55 100644 (file)
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -258,8 +258,6 @@
 #define YT8531_SCR_CLK_SRC_CLOCK_FROM_DIGITAL  3
 #define YT8531_SCR_CLK_SRC_REF_25M             4
 #define YT8531_SCR_CLK_SRC_SSC_25M             5
-#define YT8531S_SYNCE_CFG_REG                  0xA012
-#define YT8531S_SCR_SYNCE_ENABLE               BIT(6)
 
 /* Extended Register  end */
 
@@ -858,7 +856,32 @@ static int yt8521_probe(struct phy_device *phydev)
                        return -EINVAL;
                }
        } else if (phydev->drv->phy_id == PHY_ID_YT8531S) {
-               return 0;
+               switch (freq) {
+               case YTPHY_DTS_OUTPUT_CLK_DIS:
+                       mask = YT8531_SCR_SYNCE_ENABLE;
+                       val = 0;
+                       break;
+               case YTPHY_DTS_OUTPUT_CLK_25M:
+                       mask = YT8531_SCR_SYNCE_ENABLE |
+                              YT8531_SCR_CLK_SRC_MASK |
+                              YT8531_SCR_CLK_FRE_SEL_125M;
+                       val = YT8531_SCR_SYNCE_ENABLE |
+                             FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+                                        YT8531_SCR_CLK_SRC_REF_25M);
+                       break;
+               case YTPHY_DTS_OUTPUT_CLK_125M:
+                       mask = YT8531_SCR_SYNCE_ENABLE |
+                              YT8531_SCR_CLK_SRC_MASK |
+                              YT8531_SCR_CLK_FRE_SEL_125M;
+                       val = YT8531_SCR_SYNCE_ENABLE |
+                             YT8531_SCR_CLK_FRE_SEL_125M |
+                             FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+                                        YT8531_SCR_CLK_SRC_PLL_125M);
+                       break;
+               default:
+                       phydev_warn(phydev, "Freq err:%u\n", freq);
+                       return -EINVAL;
+               }
        } else {
                phydev_warn(phydev, "PHY id err\n");
                return -EINVAL;
@@ -869,26 +892,6 @@ static int yt8521_probe(struct phy_device *phydev)
 }
 
 /**
- * yt8531s_probe() - read chip config then set suitable polling_mode
- * @phydev: a pointer to a &struct phy_device
- *
- * returns 0 or negative errno code
- */
-static int yt8531s_probe(struct phy_device *phydev)
-{
-       int ret;
-
-       /* Disable SyncE clock output by default */
-       ret = ytphy_modify_ext_with_lock(phydev, YT8531S_SYNCE_CFG_REG,
-                                        YT8531S_SCR_SYNCE_ENABLE, 0);
-       if (ret < 0)
-               return ret;
-
-       /* same as yt8521_probe */
-       return yt8521_probe(phydev);
-}
-
-/**
  * ytphy_utp_read_lpa() - read LPA then setup lp_advertising for utp
  * @phydev: a pointer to a &struct phy_device
  *
@@ -1970,7 +1973,7 @@ static struct phy_driver motorcomm_phy_drvs[] = {
                PHY_ID_MATCH_EXACT(PHY_ID_YT8531S),
                .name           = "YT8531S Gigabit Ethernet",
                .get_features   = yt8521_get_features,
-               .probe          = yt8531s_probe,
+               .probe          = yt8521_probe,
                .read_page      = yt8521_read_page,
                .write_page     = yt8521_write_page,
                .get_wol        = ytphy_get_wol,