Add cm_t335 board directory, config file. Enable build.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[trini: Adapt Makefile]
Signed-off-by: Tom Rini <trini@ti.com>
#define MT41J128MJT125_PHY_FIFO_WE 0x100
#define MT41J128MJT125_IOCTRL_VALUE 0x18B
+/* Micron MT41J64M16JT-125 */
+#define MT41J64MJT125_EMIF_SDCFG 0x61C04A32
+
+/* Micron MT41J256M16JT-125 */
+#define MT41J256MJT125_EMIF_SDCFG 0x61C04B32
+
/* Micron MT41J256M8HX-15E */
#define MT41J256M8HX15E_EMIF_READ_LATENCY 0x06
#define MT41J256M8HX15E_EMIF_TIM1 0x0888A39B
--- /dev/null
+#
+# Copyright (C) 2013 Compulab Ltd - http://compulab.co.il/
+#
+# Author: Ilya Ledvich <ilya@compulab.co.il>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += $(BOARD).o
+obj-$(CONFIG_SPL_BUILD) += mux.o spl.o
--- /dev/null
+/*
+ * Board functions for Compulab CM-T335 board
+ *
+ * Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Ilya Ledvich <ilya@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <miiphy.h>
+#include <cpsw.h>
+
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware_am33xx.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+
+#include "../common/eeprom.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ */
+int board_init(void)
+{
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ gpmc_init();
+
+ return 0;
+}
+
+#if defined (CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+ return;
+}
+
+static struct cpsw_slave_data cpsw_slave = {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_id = 0,
+ .phy_if = PHY_INTERFACE_MODE_RGMII,
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = CPSW_MDIO_BASE,
+ .cpsw_base = CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = &cpsw_slave,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .bd_ram_ofs = 0x2000,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+
+/* PHY reset GPIO */
+#define GPIO_PHY_RST GPIO_PIN(3, 7)
+
+static void board_phy_init(void)
+{
+ gpio_request(GPIO_PHY_RST, "phy_rst");
+ gpio_direction_output(GPIO_PHY_RST, 0);
+ mdelay(2);
+ gpio_set_value(GPIO_PHY_RST, 1);
+ mdelay(2);
+}
+
+static void get_efuse_mac_addr(uchar *enetaddr)
+{
+ uint32_t mac_hi, mac_lo;
+ struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+ mac_lo = readl(&cdev->macid0l);
+ mac_hi = readl(&cdev->macid0h);
+ enetaddr[0] = mac_hi & 0xFF;
+ enetaddr[1] = (mac_hi & 0xFF00) >> 8;
+ enetaddr[2] = (mac_hi & 0xFF0000) >> 16;
+ enetaddr[3] = (mac_hi & 0xFF000000) >> 24;
+ enetaddr[4] = mac_lo & 0xFF;
+ enetaddr[5] = (mac_lo & 0xFF00) >> 8;
+}
+
+/*
+ * Routine: handle_mac_address
+ * Description: prepare MAC address for on-board Ethernet.
+ */
+static int handle_mac_address(void)
+{
+ uchar enetaddr[6];
+ int rv;
+
+ rv = eth_getenv_enetaddr("ethaddr", enetaddr);
+ if (rv)
+ return 0;
+
+ rv = cl_eeprom_read_mac_addr(enetaddr);
+ if (rv)
+ get_efuse_mac_addr(enetaddr);
+
+ if (!is_valid_ether_addr(enetaddr))
+ return -1;
+
+ return eth_setenv_enetaddr("ethaddr", enetaddr);
+}
+
+#define AR8051_PHY_DEBUG_ADDR_REG 0x1d
+#define AR8051_PHY_DEBUG_DATA_REG 0x1e
+#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
+#define AR8051_RGMII_TX_CLK_DLY 0x100
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, n = 0;
+ const char *devname;
+ struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+ rv = handle_mac_address();
+ if (rv)
+ printf("No MAC address found!\n");
+
+ writel(RGMII_MODE_ENABLE | RGMII_INT_DELAY, &cdev->miisel);
+
+ board_phy_init();
+
+ rv = cpsw_register(&cpsw_data);
+ if (rv < 0)
+ printf("Error %d registering CPSW switch\n", rv);
+ else
+ n += rv;
+
+ /*
+ * CPSW RGMII Internal Delay Mode is not supported in all PVT
+ * operating points. So we must set the TX clock delay feature
+ * in the AR8051 PHY. Since we only support a single ethernet
+ * device, we only do this for the first instance.
+ */
+ devname = miiphy_get_current_dev();
+
+ miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_ADDR_REG,
+ AR8051_DEBUG_RGMII_CLK_DLY_REG);
+ miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_DATA_REG,
+ AR8051_RGMII_TX_CLK_DLY);
+ return n;
+}
+#endif /* CONFIG_DRIVER_TI_CPSW && !CONFIG_SPL_BUILD */
--- /dev/null
+/*
+ * Pinmux configuration for Compulab CM-T335 board
+ *
+ * Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Ilya Ledvich <ilya@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+
+static struct module_pin_mux uart0_pin_mux[] = {
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
+ {-1},
+};
+
+static struct module_pin_mux uart1_pin_mux[] = {
+ {OFFSET(uart1_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},
+ {OFFSET(uart1_txd), (MODE(0) | PULLUDEN)},
+ {OFFSET(uart1_ctsn), (MODE(0) | PULLUP_EN | RXACTIVE)},
+ {OFFSET(uart1_rtsn), (MODE(0) | PULLUDEN)},
+ {-1},
+};
+
+static struct module_pin_mux mmc0_pin_mux[] = {
+ {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},
+ {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},
+ {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)},
+ {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)},
+ {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},
+ {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},
+ {-1},
+};
+
+static struct module_pin_mux i2c0_pin_mux[] = {
+ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDDIS | SLEWCTRL)},
+ {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDDIS | SLEWCTRL)},
+ {-1},
+};
+
+static struct module_pin_mux i2c1_pin_mux[] = {
+ /* I2C_DATA */
+ {OFFSET(uart0_ctsn), (MODE(3) | RXACTIVE | PULLUDDIS | SLEWCTRL)},
+ /* I2C_SCLK */
+ {OFFSET(uart0_rtsn), (MODE(3) | RXACTIVE | PULLUDDIS | SLEWCTRL)},
+ {-1},
+};
+
+static struct module_pin_mux rgmii1_pin_mux[] = {
+ {OFFSET(mii1_txen), MODE(2)}, /* RGMII1_TCTL */
+ {OFFSET(mii1_rxdv), MODE(2) | RXACTIVE}, /* RGMII1_RCTL */
+ {OFFSET(mii1_txd3), MODE(2)}, /* RGMII1_TD3 */
+ {OFFSET(mii1_txd2), MODE(2)}, /* RGMII1_TD2 */
+ {OFFSET(mii1_txd1), MODE(2)}, /* RGMII1_TD1 */
+ {OFFSET(mii1_txd0), MODE(2)}, /* RGMII1_TD0 */
+ {OFFSET(mii1_txclk), MODE(2)}, /* RGMII1_TCLK */
+ {OFFSET(mii1_rxclk), MODE(2) | RXACTIVE}, /* RGMII1_RCLK */
+ {OFFSET(mii1_rxd3), MODE(2) | RXACTIVE}, /* RGMII1_RD3 */
+ {OFFSET(mii1_rxd2), MODE(2) | RXACTIVE}, /* RGMII1_RD2 */
+ {OFFSET(mii1_rxd1), MODE(2) | RXACTIVE}, /* RGMII1_RD1 */
+ {OFFSET(mii1_rxd0), MODE(2) | RXACTIVE}, /* RGMII1_RD0 */
+ {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
+ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
+ {-1},
+};
+
+static struct module_pin_mux nand_pin_mux[] = {
+ {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
+ {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
+ {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
+ {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
+ {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
+ {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
+ {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
+ {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
+ {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
+ {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
+ {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+ {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
+ {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
+ {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
+ {-1},
+};
+
+static struct module_pin_mux eth_phy_rst_pin_mux[] = {
+ {OFFSET(emu0), (MODE(7) | PULLUDDIS)}, /* GPIO3_7 */
+ {-1},
+};
+
+void set_uart_mux_conf(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+ configure_module_pin_mux(uart1_pin_mux);
+}
+
+void set_mux_conf_regs(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+ configure_module_pin_mux(i2c1_pin_mux);
+ configure_module_pin_mux(rgmii1_pin_mux);
+ configure_module_pin_mux(eth_phy_rst_pin_mux);
+ configure_module_pin_mux(mmc0_pin_mux);
+ configure_module_pin_mux(nand_pin_mux);
+}
--- /dev/null
+/*
+ * SPL specific code for Compulab CM-T335 board
+ *
+ * Board functions for Compulab CM-T335 board
+ *
+ * Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Ilya Ledvich <ilya@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/clocks_am33xx.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware_am33xx.h>
+#include <asm/sizes.h>
+
+static const struct ddr_data ddr3_data = {
+ .datardsratio0 = MT41J128MJT125_RD_DQS,
+ .datawdsratio0 = MT41J128MJT125_WR_DQS,
+ .datafwsratio0 = MT41J128MJT125_PHY_FIFO_WE,
+ .datawrsratio0 = MT41J128MJT125_PHY_WR_DATA,
+ .datadldiff0 = PHY_DLL_LOCK_DIFF,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+ .cmd0csratio = MT41J128MJT125_RATIO,
+ .cmd0dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
+ .cmd0iclkout = MT41J128MJT125_INVERT_CLKOUT,
+
+ .cmd1csratio = MT41J128MJT125_RATIO,
+ .cmd1dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
+ .cmd1iclkout = MT41J128MJT125_INVERT_CLKOUT,
+
+ .cmd2csratio = MT41J128MJT125_RATIO,
+ .cmd2dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
+ .cmd2iclkout = MT41J128MJT125_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+ .sdram_config = MT41J128MJT125_EMIF_SDCFG,
+ .ref_ctrl = MT41J128MJT125_EMIF_SDREF,
+ .sdram_tim1 = MT41J128MJT125_EMIF_TIM1,
+ .sdram_tim2 = MT41J128MJT125_EMIF_TIM2,
+ .sdram_tim3 = MT41J128MJT125_EMIF_TIM3,
+ .zq_config = MT41J128MJT125_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41J128MJT125_EMIF_READ_LATENCY |
+ PHY_EN_DYN_PWRDN,
+};
+
+const struct dpll_params dpll_ddr = {
+/* M N M2 M3 M4 M5 M6 */
+ 303, (V_OSCK/1000000) - 1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+ struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+ /* Get the frequency */
+ dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+ /* Set MPU Frequency to what we detected now that voltages are set */
+ do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ return &dpll_ddr;
+}
+
+static void probe_sdram_size(long size)
+{
+ switch (size) {
+ case SZ_512M:
+ ddr3_emif_reg_data.sdram_config = MT41J256MJT125_EMIF_SDCFG;
+ break;
+ case SZ_256M:
+ ddr3_emif_reg_data.sdram_config = MT41J128MJT125_EMIF_SDCFG;
+ break;
+ case SZ_128M:
+ ddr3_emif_reg_data.sdram_config = MT41J64MJT125_EMIF_SDCFG;
+ break;
+ default:
+ puts("Failed configuring DRAM, resetting...\n\n");
+ reset_cpu(0);
+ }
+ debug("%s: setting DRAM size to %ldM\n", __func__, size >> 20);
+ config_ddr(303, MT41J128MJT125_IOCTRL_VALUE, &ddr3_data,
+ &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+}
+
+void sdram_init(void)
+{
+ long size = SZ_1G;
+
+ do {
+ size = size / 2;
+ probe_sdram_size(size);
+ } while (get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, size) < size);
+
+ return;
+}
--- /dev/null
+/*
+ * Copyright (c) 2004-2008 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ *(.__image_copy_start)
+ CPUDIR/start.o (.text*)
+ board/compulab/cm_t335/libcm_t335.o (.text*)
+ *(.text*)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+ . = ALIGN(4);
+ .data : {
+ *(.data*)
+ }
+
+ . = ALIGN(4);
+
+ . = .;
+
+ . = ALIGN(4);
+ .u_boot_list : {
+ KEEP(*(SORT(.u_boot_list*)));
+ }
+
+ . = ALIGN(4);
+
+ .image_copy_end :
+ {
+ *(.__image_copy_end)
+ }
+
+ .rel_dyn_start :
+ {
+ *(.__rel_dyn_start)
+ }
+
+ .rel.dyn : {
+ *(.rel*)
+ }
+
+ .rel_dyn_end :
+ {
+ *(.__rel_dyn_end)
+ }
+
+ _end = .;
+
+ /*
+ * Deprecated: this MMU section is used by pxa at present but
+ * should not be used by new boards/CPUs.
+ */
+ . = ALIGN(4096);
+ .mmutable : {
+ *(.mmutable)
+ }
+
+/*
+ * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
+ * __bss_base and __bss_limit are for linker only (overlay ordering)
+ */
+
+ .bss_start __rel_dyn_start (OVERLAY) : {
+ KEEP(*(.__bss_start));
+ __bss_base = .;
+ }
+
+ .bss __bss_base (OVERLAY) : {
+ *(.bss*)
+ . = ALIGN(4);
+ __bss_limit = .;
+ }
+
+ .bss_end __bss_limit (OVERLAY) : {
+ KEEP(*(.__bss_end));
+ }
+
+ /DISCARD/ : { *(.dynsym) }
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
+}
Active arm armv7 - armltd vexpress vexpress_ca15_tc2 - -
Active arm armv7 - armltd vexpress vexpress_ca5x2 - Matt Waddel <matt.waddel@linaro.org>
Active arm armv7 - armltd vexpress vexpress_ca9x4 - Matt Waddel <matt.waddel@linaro.org>
+Active arm armv7 am33xx compulab cm_t335 cm_t335 cm_t335 Igor Grinberg <grinberg@compulab.co.il>
Active arm armv7 am33xx isee igep0033 am335x_igep0033 - Enric Balletbo i Serra <eballetbo@iseebcn.com>
Active arm armv7 am33xx phytec pcm051 pcm051 pcm051 Lars Poeschel <poeschel@lemonage.de>
Active arm armv7 am33xx siemens dxr2 dxr2 - Roger Meier <r.meier@siemens.com>
--- /dev/null
+/*
+ * Config file for Compulab CM-T335 board
+ *
+ * Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Ilya Ledvich <ilya@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_CM_T335_H
+#define __CONFIG_CM_T335_H
+
+#define CONFIG_CM_T335
+#define CONFIG_NAND
+
+#include <configs/ti_am335x_common.h>
+
+#undef CONFIG_BOARD_LATE_INIT
+#undef CONFIG_SPI
+#undef CONFIG_OMAP3_SPI
+#undef CONFIG_CMD_SPI
+#undef CONFIG_SPL_OS_BOOT
+#undef CONFIG_BOOTCOUNT_LIMIT
+#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
+
+#undef CONFIG_MAX_RAM_BANK_SIZE
+#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* 512MB */
+
+#undef CONFIG_SYS_PROMPT
+#define CONFIG_SYS_PROMPT "CM-T335 # "
+
+#define CONFIG_OMAP_COMMON
+
+#define MACH_TYPE_CM_T335 4586 /* Until the next sync */
+#define CONFIG_MACH_TYPE MACH_TYPE_CM_T335
+
+/* Clock Defines */
+#define V_OSCK 25000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK)
+
+#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
+
+#ifndef CONFIG_SPL_BUILD
+#define MMCARGS \
+ "mmcdev=0\0" \
+ "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
+ "mmcrootfstype=ext4\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0"
+
+#define NANDARGS \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "nandroot=ubi0:rootfs rw\0" \
+ "nandrootfstype=ubifs\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype} " \
+ "ubi.mtd=${rootfs_name}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nboot ${loadaddr} nand0 900000; " \
+ "bootm ${loadaddr}\0"
+
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=82000000\0" \
+ "console=ttyO0,115200n8\0" \
+ "rootfs_name=rootfs\0" \
+ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source ${loadaddr}\0" \
+ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
+ MMCARGS \
+ NANDARGS
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+#endif /* CONFIG_SPL_BUILD */
+
+#define CONFIG_TIMESTAMP
+#define CONFIG_SYS_AUTOLOAD "no"
+
+/* Serial console configuration */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SERIAL1 1 /* UART0 */
+
+/* NS16550 Configuration */
+#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
+#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
+#define CONFIG_BAUDRATE 115200
+
+/* I2C Configuration */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/* SPL */
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+/* Network. */
+#define CONFIG_PHY_GIGE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR 0
+#define CONFIG_PHY_ATHEROS
+
+/* NAND support */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12, 13, 14, 15, 16, 17, \
+ 18, 19, 20, 21, 22, 23, 24, 25, \
+ 26, 27, 28, 29, 30, 31, 32, 33, \
+ 34, 35, 36, 37, 38, 39, 40, 41, \
+ 42, 43, 44, 45, 46, 47, 48, 49, \
+ 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 14
+
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+
+#undef CONFIG_SYS_NAND_U_BOOT_OFFS
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
+
+#define CONFIG_CMD_NAND
+#define GPMC_NAND_ECC_LP_x8_LAYOUT
+#define MTDIDS_DEFAULT "nand0=nand"
+#define MTDPARTS_DEFAULT "mtdparts=nand:2m(spl)," \
+ "1m(u-boot),1m(u-boot-env)," \
+ "1m(dtb),4m(splash)," \
+ "6m(kernel),-(rootfs)"
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x300000 /* environment starts here */
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* GPIO pin + bank to pin ID mapping */
+#define GPIO_PIN(_bank, _pin) ((_bank << 5) + _pin)
+
+#endif /* __CONFIG_CM_T335_H */
+
projects / platform / kernel / u-boot.git / commitdiff