stv0991: configure clock & pad muxing for qspi
authorVikas Manocha <vikas.manocha@st.com>
Fri, 3 Jul 2015 01:29:40 +0000 (18:29 -0700)
committerJagan Teki <jteki@openedev.com>
Fri, 3 Jul 2015 08:20:53 +0000 (13:50 +0530)
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
arch/arm/cpu/armv7/stv0991/clock.c
arch/arm/cpu/armv7/stv0991/pinmux.c
arch/arm/include/asm/arch-stv0991/stv0991_cgu.h
arch/arm/include/asm/arch-stv0991/stv0991_creg.h
arch/arm/include/asm/arch-stv0991/stv0991_periph.h
board/st/stv0991/stv0991.c

index 70b8a8d..26c0d36 100644 (file)
@@ -33,7 +33,9 @@ void clock_setup(int peripheral)
                /* Clock selection for ethernet tx_clk & rx_clk*/
                writel((readl(&stv0991_cgu_regs->eth_ctrl) & ETH_CLK_MASK)
                                | ETH_CLK_CTRL, &stv0991_cgu_regs->eth_ctrl);
-
+               break;
+       case QSPI_CLOCK_CFG:
+               writel(QSPI_CLK_CTRL, &stv0991_cgu_regs->qspi_freq);
                break;
        default:
                break;
index 1d086a2..24c67fa 100644 (file)
@@ -55,6 +55,11 @@ int stv0991_pinmux_config(int peripheral)
                                ETH_M_VDD_CFG, &stv0991_creg->vdd_pad1);
 
                break;
+       case QSPI_CS_CLK_PAD:
+               writel((readl(&stv0991_creg->mux13) & FLASH_CS_NC_MASK) |
+                               CFG_FLASH_CS_NC, &stv0991_creg->mux13);
+               writel((readl(&stv0991_creg->mux13) & FLASH_CLK_MASK) |
+                               CFG_FLASH_CLK, &stv0991_creg->mux13);
        default:
                break;
        }
index ddcbb57..f0045f3 100644 (file)
@@ -113,4 +113,19 @@ struct stv0991_cgu_regs {
 
 #define ETH_CLK_CTRL                   (ETH_CLK_RX_EXT_PHY << RX_CLK_SHIFT \
                                        | ETH_CLK_TX_EXT_PHY)
+/* CGU qspi clock */
+#define DIV_HCLK1_SHIFT                        9
+#define DIV_CRYP_SHIFT                 6
+#define MDIV_QSPI_SHIFT                        3
+
+#define CLK_QSPI_OSC                   0
+#define CLK_QSPI_MCLK                  1
+#define CLK_QSPI_PLL1                  2
+#define CLK_QSPI_PLL2                  3
+
+#define QSPI_CLK_CTRL                  (3 << DIV_HCLK1_SHIFT \
+                                       | 1 << DIV_CRYP_SHIFT \
+                                       | 0 << MDIV_QSPI_SHIFT \
+                                       | CLK_QSPI_OSC)
+
 #endif
index c804eb5..737c952 100644 (file)
@@ -49,6 +49,15 @@ struct stv0991_creg {
        u32 vdd_comp1;          /* offset 0x400 */
 };
 
+/* CREG MUX 13 register */
+#define FLASH_CS_NC_SHIFT      4
+#define FLASH_CS_NC_MASK       ~(7 << FLASH_CS_NC_SHIFT)
+#define CFG_FLASH_CS_NC                (0 << FLASH_CS_NC_SHIFT)
+
+#define FLASH_CLK_SHIFT                0
+#define FLASH_CLK_MASK         ~(7 << FLASH_CLK_SHIFT)
+#define CFG_FLASH_CLK          (0 << FLASH_CLK_SHIFT)
+
 /* CREG MUX 12 register */
 #define GPIOC_30_MUX_SHIFT     24
 #define GPIOC_30_MUX_MASK      ~(1 << GPIOC_30_MUX_SHIFT)
index f728c83..725da83 100644 (file)
@@ -18,6 +18,7 @@ enum periph_id {
        UART_GPIOC_30_31 = 0,
        UART_GPIOB_16_17,
        ETH_GPIOB_10_31_C_0_4,
+       QSPI_CS_CLK_PAD,
        PERIPH_ID_I2C0,
        PERIPH_ID_I2C1,
        PERIPH_ID_I2C2,
@@ -39,6 +40,7 @@ enum periph_id {
 enum periph_clock {
        UART_CLOCK_CFG = 0,
        ETH_CLOCK_CFG,
+       QSPI_CLOCK_CFG,
 };
 
 #endif /* __ASM_ARM_ARCH_PERIPH_H */
index 09f973f..add1ce1 100644 (file)
@@ -55,12 +55,20 @@ int board_eth_enable(void)
        return 0;
 }
 
+int board_qspi_enable(void)
+{
+       stv0991_pinmux_config(QSPI_CS_CLK_PAD);
+       clock_setup(QSPI_CLOCK_CFG);
+       return 0;
+}
+
 /*
  * Miscellaneous platform dependent initialisations
  */
 int board_init(void)
 {
        board_eth_enable();
+       board_qspi_enable();
        return 0;
 }