uint16_t chan;
int i;
- /* enab DEBI and audio pins, enable I2C interface. */
+ /* Enable DEBI and audio pins, enable I2C interface */
MC_ENABLE(P_MC1, MC1_DEBI | MC1_AUDIO | MC1_I2C);
- /* Configure DEBI operating mode. */
- WR7146(P_DEBICFG, DEBI_CFG_SLAVE16 /* Local bus is 16 */
- /* bits wide. */
- | (DEBI_TOUT << DEBI_CFG_TOUT_BIT)
-
- /* Declare DEBI */
- /* transfer timeout */
- /* interval. */
- |DEBI_SWAP /* Set up byte lane */
- /* steering. */
- | DEBI_CFG_INTEL); /* Intel-compatible */
- /* local bus (DEBI */
- /* never times out). */
-
- /* DEBI INIT S626 WR7146( P_DEBICFG, DEBI_CFG_INTEL | DEBI_CFG_TOQ */
- /* | DEBI_CFG_INCQ| DEBI_CFG_16Q); //end */
-
- /* Paging is disabled. */
- WR7146(P_DEBIPAGE, DEBI_PAGE_DISABLE); /* Disable MMU paging. */
-
- /* Init GPIO so that ADC Start* is negated. */
+
+ /*
+ * Configure DEBI operating mode
+ *
+ * Local bus is 16 bits wide
+ * Declare DEBI transfer timeout interval
+ * Set up byte lane steering
+ * Intel-compatible local bus (DEBI never times out)
+ */
+ WR7146(P_DEBICFG, DEBI_CFG_SLAVE16 |
+ (DEBI_TOUT << DEBI_CFG_TOUT_BIT) |
+ DEBI_SWAP | DEBI_CFG_INTEL);
+
+ /* Disable MMU paging */
+ WR7146(P_DEBIPAGE, DEBI_PAGE_DISABLE);
+
+ /* Init GPIO so that ADC Start* is negated */
WR7146(P_GPIO, GPIO_BASE | GPIO1_HI);
/* I2C device address for onboard eeprom (revb) */
devpriv->I2CAdrs = 0xA0;
- /* Issue an I2C ABORT command to halt any I2C operation in */
- /* progress and reset BUSY flag. */
+ /*
+ * Issue an I2C ABORT command to halt any I2C
+ * operation in progress and reset BUSY flag.
+ */
WR7146(P_I2CSTAT, I2C_CLKSEL | I2C_ABORT);
- /* Write I2C control: abort any I2C activity. */
MC_ENABLE(P_MC2, MC2_UPLD_IIC);
- /* Invoke command upload */
while ((RR7146(P_MC2) & MC2_UPLD_IIC) == 0)
;
- /* and wait for upload to complete. */
- /* Per SAA7146 data sheet, write to STATUS reg twice to
- * reset all I2C error flags. */
+ /*
+ * Per SAA7146 data sheet, write to STATUS
+ * reg twice to reset all I2C error flags.
+ */
for (i = 0; i < 2; i++) {
WR7146(P_I2CSTAT, I2C_CLKSEL);
- /* Write I2C control: reset error flags. */
- MC_ENABLE(P_MC2, MC2_UPLD_IIC); /* Invoke command upload */
+ MC_ENABLE(P_MC2, MC2_UPLD_IIC);
while (!MC_TEST(P_MC2, MC2_UPLD_IIC))
;
- /* and wait for upload to complete. */
}
- /* Init audio interface functional attributes: set DAC/ADC
+ /*
+ * Init audio interface functional attributes: set DAC/ADC
* serial clock rates, invert DAC serial clock so that
* DAC data setup times are satisfied, enable DAC serial
* clock out.
*/
-
WR7146(P_ACON2, ACON2_INIT);
- /* Set up TSL1 slot list, which is used to control the
+ /*
+ * Set up TSL1 slot list, which is used to control the
* accumulation of ADC data: RSD1 = shift data in on SD1.
- * SIB_A1 = store data uint8_t at next available location in
- * FB BUFFER1 register. */
+ * SIB_A1 = store data uint8_t at next available location
+ * in FB BUFFER1 register.
+ */
WR7146(P_TSL1, RSD1 | SIB_A1);
- /* Fetch ADC high data uint8_t. */
WR7146(P_TSL1 + 4, RSD1 | SIB_A1 | EOS);
- /* Fetch ADC low data uint8_t; end of TSL1. */
- /* enab TSL1 slot list so that it executes all the time. */
+ /* Enable TSL1 slot list so that it executes all the time */
WR7146(P_ACON1, ACON1_ADCSTART);
- /* Initialize RPS registers used for ADC. */
-
- /* Physical start of RPS program. */
- WR7146(P_RPSADDR1, (uint32_t) devpriv->RPSBuf.PhysicalBase);
+ /*
+ * Initialize RPS registers used for ADC
+ */
+ /* Physical start of RPS program */
+ WR7146(P_RPSADDR1, (uint32_t)devpriv->RPSBuf.PhysicalBase);
+ /* RPS program performs no explicit mem writes */
WR7146(P_RPSPAGE1, 0);
- /* RPS program performs no explicit mem writes. */
- WR7146(P_RPS1_TOUT, 0); /* Disable RPS timeouts. */
+ /* Disable RPS timeouts */
+ WR7146(P_RPS1_TOUT, 0);
#if 0
/*
}
#endif /* SAA7146 BUG WORKAROUND */
- /* end initADC */
-
- /* init the DAC interface */
+ /*
+ * Initialize the DAC interface
+ */
- /* Init Audio2's output DMAC attributes: burst length = 1
- * DWORD, threshold = 1 DWORD.
+ /*
+ * Init Audio2's output DMAC attributes:
+ * burst length = 1 DWORD
+ * threshold = 1 DWORD.
*/
WR7146(P_PCI_BT_A, 0);
- /* Init Audio2's output DMA physical addresses. The protection
+ /*
+ * Init Audio2's output DMA physical addresses. The protection
* address is set to 1 DWORD past the base address so that a
* single DWORD will be transferred each time a DMA transfer is
- * enabled. */
-
+ * enabled.
+ */
pPhysBuf = devpriv->ANABuf.PhysicalBase +
(DAC_WDMABUF_OS * sizeof(uint32_t));
+ WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf);
+ WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t)));
- WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf); /* Buffer base adrs. */
- WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t))); /* Protection address. */
-
- /* Cache Audio2's output DMA buffer logical address. This is
- * where DAC data is buffered for A2 output DMA transfers. */
+ /*
+ * Cache Audio2's output DMA buffer logical address. This is
+ * where DAC data is buffered for A2 output DMA transfers.
+ */
devpriv->pDacWBuf = (uint32_t *)devpriv->ANABuf.LogicalBase +
DAC_WDMABUF_OS;
- /* Audio2's output channels does not use paging. The protection
- * violation handling bit is set so that the DMAC will
- * automatically halt and its PCI address pointer will be reset
- * when the protection address is reached. */
-
+ /*
+ * Audio2's output channels does not use paging. The
+ * protection violation handling bit is set so that the
+ * DMAC will automatically halt and its PCI address pointer
+ * will be reset when the protection address is reached.
+ */
WR7146(P_PAGEA2_OUT, 8);
- /* Initialize time slot list 2 (TSL2), which is used to control
+ /*
+ * Initialize time slot list 2 (TSL2), which is used to control
* the clock generation for and serialization of data to be sent
* to the DAC devices. Slot 0 is a NOP that is used to trap TSL
* execution; this permits other slots to be safely modified
* not yet finished executing.
*/
+ /* Slot 0: Trap TSL execution, shift 0xFF into FB_BUFFER2 */
SETVECT(0, XSD2 | RSD3 | SIB_A2 | EOS);
- /* Slot 0: Trap TSL execution, shift 0xFF into FB_BUFFER2. */
- /* Initialize slot 1, which is constant. Slot 1 causes a
+ /*
+ * Initialize slot 1, which is constant. Slot 1 causes a
* DWORD to be transferred from audio channel 2's output FIFO
* to the FIFO's output buffer so that it can be serialized
* and sent to the DAC during subsequent slots. All remaining
* slots are dynamically populated as required by the target
* DAC device.
*/
+
+ /* Slot 1: Fetch DWORD from Audio2's output FIFO */
SETVECT(1, LF_A2);
- /* Slot 1: Fetch DWORD from Audio2's output FIFO. */
- /* Start DAC's audio interface (TSL2) running. */
+ /* Start DAC's audio interface (TSL2) running */
WR7146(P_ACON1, ACON1_DACSTART);
- /* end init DAC interface */
-
- /* Init Trim DACs to calibrated values. Do it twice because the
+ /*
+ * Init Trim DACs to calibrated values. Do it twice because the
* SAA7146 audio channel does not always reset properly and
* sometimes causes the first few TrimDAC writes to malfunction.
*/
-
LoadTrimDACs(dev);
- LoadTrimDACs(dev); /* Insurance. */
+ LoadTrimDACs(dev);
- /* Manually init all gate array hardware in case this is a soft
+ /*
+ * Manually init all gate array hardware in case this is a soft
* reset (we have no way of determining whether this is a warm
* or cold start). This is necessary because the gate array will
* reset only in response to a PCI hard reset; there is no soft
- * reset function. */
+ * reset function.
+ */
- /* Init all DAC outputs to 0V and init all DAC setpoint and
+ /*
+ * Init all DAC outputs to 0V and init all DAC setpoint and
* polarity images.
*/
for (chan = 0; chan < S626_DAC_CHANNELS; chan++)
SetDAC(dev, chan, 0);
- /* Init counters. */
+ /* Init counters */
CountersInit(dev);
- /* Without modifying the state of the Battery Backup enab, disable
+ /*
+ * Without modifying the state of the Battery Backup enab, disable
* the watchdog timer, set DIO channels 0-5 to operate in the
* standard DIO (vs. counter overflow) mode, disable the battery
* charger, and reset the watchdog interval selector to zero.
WriteMISC2(dev, (uint16_t)(DEBIread(dev, LP_RDMISC2) &
MISC2_BATT_ENABLE));
- /* Initialize the digital I/O subsystem. */
+ /* Initialize the digital I/O subsystem */
s626_dio_init(dev);
/* enable interrupt test */
- /* writel(IRQ_GPIO3 | IRQ_RPS1,devpriv->base_addr+P_IER); */
+ /* writel(IRQ_GPIO3 | IRQ_RPS1, devpriv->base_addr + P_IER); */
}
static int s626_attach_pci(struct comedi_device *dev, struct pci_dev *pcidev)
projects / profile / ivi / kernel-x86-ivi.git / commitdiff