+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2011
- * eInfochips Ltd. <www.einfochips.com>
- * Written-by: Ajay Bhargav <contact@8051projects.net>
- *
- * (C) Copyright 2010
- * Marvell Semiconductor <www.marvell.com>
- * Contributor: Mahavir Jain <mjain@marvell.com>
- */
-
-#include <common.h>
-#include <log.h>
-#include <net.h>
-#include <malloc.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/types.h>
-#include <asm/byteorder.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/mii.h>
-#include <asm/io.h>
-#include <asm/arch/armada100.h>
-#include "armada100_fec.h"
-
-#define PHY_ADR_REQ 0xFF /* Magic number to read/write PHY address */
-
-#ifdef DEBUG
-static int eth_dump_regs(struct eth_device *dev)
-{
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct armdfec_reg *regs = darmdfec->regs;
- unsigned int i = 0;
-
- printf("\noffset: phy_adr, value: 0x%x\n", readl(®s->phyadr));
- printf("offset: smi, value: 0x%x\n", readl(®s->smi));
- for (i = 0x400; i <= 0x4e4; i += 4)
- printf("offset: 0x%x, value: 0x%x\n",
- i, readl(ARMD1_FEC_BASE + i));
- return 0;
-}
-#endif
-
-static int armdfec_phy_timeout(u32 *reg, u32 flag, int cond)
-{
- u32 timeout = PHY_WAIT_ITERATIONS;
- u32 reg_val;
-
- while (--timeout) {
- reg_val = readl(reg);
- if (cond && (reg_val & flag))
- break;
- else if (!cond && !(reg_val & flag))
- break;
- udelay(PHY_WAIT_MICRO_SECONDS);
- }
- return !timeout;
-}
-
-static int smi_reg_read(struct mii_dev *bus, int phy_addr, int devad,
- int phy_reg)
-{
- u16 value = 0;
- struct eth_device *dev = eth_get_dev_by_name(bus->name);
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct armdfec_reg *regs = darmdfec->regs;
- u32 val;
-
- if (phy_addr == PHY_ADR_REQ && phy_reg == PHY_ADR_REQ) {
- val = readl(®s->phyadr);
- value = val & 0x1f;
- return value;
- }
-
- /* check parameters */
- if (phy_addr > PHY_MASK) {
- printf("ARMD100 FEC: (%s) Invalid phy address: 0x%X\n",
- __func__, phy_addr);
- return -EINVAL;
- }
- if (phy_reg > PHY_MASK) {
- printf("ARMD100 FEC: (%s) Invalid register offset: 0x%X\n",
- __func__, phy_reg);
- return -EINVAL;
- }
-
- /* wait for the SMI register to become available */
- if (armdfec_phy_timeout(®s->smi, SMI_BUSY, false)) {
- printf("ARMD100 FEC: (%s) PHY busy timeout\n", __func__);
- return -1;
- }
-
- writel((phy_addr << 16) | (phy_reg << 21) | SMI_OP_R, ®s->smi);
-
- /* now wait for the data to be valid */
- if (armdfec_phy_timeout(®s->smi, SMI_R_VALID, true)) {
- val = readl(®s->smi);
- printf("ARMD100 FEC: (%s) PHY Read timeout, val=0x%x\n",
- __func__, val);
- return -1;
- }
- val = readl(®s->smi);
- value = val & 0xffff;
-
- return value;
-}
-
-static int smi_reg_write(struct mii_dev *bus, int phy_addr, int devad,
- int phy_reg, u16 value)
-{
- struct eth_device *dev = eth_get_dev_by_name(bus->name);
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct armdfec_reg *regs = darmdfec->regs;
-
- if (phy_addr == PHY_ADR_REQ && phy_reg == PHY_ADR_REQ) {
- clrsetbits_le32(®s->phyadr, 0x1f, value & 0x1f);
- return 0;
- }
-
- /* check parameters */
- if (phy_addr > PHY_MASK) {
- printf("ARMD100 FEC: (%s) Invalid phy address\n", __func__);
- return -EINVAL;
- }
- if (phy_reg > PHY_MASK) {
- printf("ARMD100 FEC: (%s) Invalid register offset\n", __func__);
- return -EINVAL;
- }
-
- /* wait for the SMI register to become available */
- if (armdfec_phy_timeout(®s->smi, SMI_BUSY, false)) {
- printf("ARMD100 FEC: (%s) PHY busy timeout\n", __func__);
- return -1;
- }
-
- writel((phy_addr << 16) | (phy_reg << 21) | SMI_OP_W | (value & 0xffff),
- ®s->smi);
- return 0;
-}
-
-/*
- * Abort any transmit and receive operations and put DMA
- * in idle state. AT and AR bits are cleared upon entering
- * in IDLE state. So poll those bits to verify operation.
- */
-static void abortdma(struct eth_device *dev)
-{
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct armdfec_reg *regs = darmdfec->regs;
- int delay;
- int maxretries = 40;
- u32 tmp;
-
- while (--maxretries) {
- writel(SDMA_CMD_AR | SDMA_CMD_AT, ®s->sdma_cmd);
- udelay(100);
-
- delay = 10;
- while (--delay) {
- tmp = readl(®s->sdma_cmd);
- if (!(tmp & (SDMA_CMD_AR | SDMA_CMD_AT)))
- break;
- udelay(10);
- }
- if (delay)
- break;
- }
-
- if (!maxretries)
- printf("ARMD100 FEC: (%s) DMA Stuck\n", __func__);
-}
-
-static inline u32 nibble_swapping_32_bit(u32 x)
-{
- return ((x & 0xf0f0f0f0) >> 4) | ((x & 0x0f0f0f0f) << 4);
-}
-
-static inline u32 nibble_swapping_16_bit(u32 x)
-{
- return ((x & 0x0000f0f0) >> 4) | ((x & 0x00000f0f) << 4);
-}
-
-static inline u32 flip_4_bits(u32 x)
-{
- return ((x & 0x01) << 3) | ((x & 0x002) << 1)
- | ((x & 0x04) >> 1) | ((x & 0x008) >> 3);
-}
-
-/*
- * This function will calculate the hash function of the address.
- * depends on the hash mode and hash size.
- * Inputs
- * mach - the 2 most significant bytes of the MAC address.
- * macl - the 4 least significant bytes of the MAC address.
- * Outputs
- * return the calculated entry.
- */
-static u32 hash_function(u32 mach, u32 macl)
-{
- u32 hashresult;
- u32 addrh;
- u32 addrl;
- u32 addr0;
- u32 addr1;
- u32 addr2;
- u32 addr3;
- u32 addrhswapped;
- u32 addrlswapped;
-
- addrh = nibble_swapping_16_bit(mach);
- addrl = nibble_swapping_32_bit(macl);
-
- addrhswapped = flip_4_bits(addrh & 0xf)
- + ((flip_4_bits((addrh >> 4) & 0xf)) << 4)
- + ((flip_4_bits((addrh >> 8) & 0xf)) << 8)
- + ((flip_4_bits((addrh >> 12) & 0xf)) << 12);
-
- addrlswapped = flip_4_bits(addrl & 0xf)
- + ((flip_4_bits((addrl >> 4) & 0xf)) << 4)
- + ((flip_4_bits((addrl >> 8) & 0xf)) << 8)
- + ((flip_4_bits((addrl >> 12) & 0xf)) << 12)
- + ((flip_4_bits((addrl >> 16) & 0xf)) << 16)
- + ((flip_4_bits((addrl >> 20) & 0xf)) << 20)
- + ((flip_4_bits((addrl >> 24) & 0xf)) << 24)
- + ((flip_4_bits((addrl >> 28) & 0xf)) << 28);
-
- addrh = addrhswapped;
- addrl = addrlswapped;
-
- addr0 = (addrl >> 2) & 0x03f;
- addr1 = (addrl & 0x003) | (((addrl >> 8) & 0x7f) << 2);
- addr2 = (addrl >> 15) & 0x1ff;
- addr3 = ((addrl >> 24) & 0x0ff) | ((addrh & 1) << 8);
-
- hashresult = (addr0 << 9) | (addr1 ^ addr2 ^ addr3);
- hashresult = hashresult & 0x07ff;
- return hashresult;
-}
-
-/*
- * This function will add an entry to the address table.
- * depends on the hash mode and hash size that was initialized.
- * Inputs
- * mach - the 2 most significant bytes of the MAC address.
- * macl - the 4 least significant bytes of the MAC address.
- * skip - if 1, skip this address.
- * rd - the RD field in the address table.
- * Outputs
- * address table entry is added.
- * 0 if success.
- * -ENOSPC if table full
- */
-static int add_del_hash_entry(struct armdfec_device *darmdfec, u32 mach,
- u32 macl, u32 rd, u32 skip, int del)
-{
- struct addr_table_entry_t *entry, *start;
- u32 newhi;
- u32 newlo;
- u32 i;
-
- newlo = (((mach >> 4) & 0xf) << 15)
- | (((mach >> 0) & 0xf) << 11)
- | (((mach >> 12) & 0xf) << 7)
- | (((mach >> 8) & 0xf) << 3)
- | (((macl >> 20) & 0x1) << 31)
- | (((macl >> 16) & 0xf) << 27)
- | (((macl >> 28) & 0xf) << 23)
- | (((macl >> 24) & 0xf) << 19)
- | (skip << HTESKIP) | (rd << HTERDBIT)
- | HTEVALID;
-
- newhi = (((macl >> 4) & 0xf) << 15)
- | (((macl >> 0) & 0xf) << 11)
- | (((macl >> 12) & 0xf) << 7)
- | (((macl >> 8) & 0xf) << 3)
- | (((macl >> 21) & 0x7) << 0);
-
- /*
- * Pick the appropriate table, start scanning for free/reusable
- * entries at the index obtained by hashing the specified MAC address
- */
- start = (struct addr_table_entry_t *)(darmdfec->htpr);
- entry = start + hash_function(mach, macl);
- for (i = 0; i < HOP_NUMBER; i++) {
- if (!(entry->lo & HTEVALID)) {
- break;
- } else {
- /* if same address put in same position */
- if (((entry->lo & 0xfffffff8) == (newlo & 0xfffffff8))
- && (entry->hi == newhi))
- break;
- }
- if (entry == start + 0x7ff)
- entry = start;
- else
- entry++;
- }
-
- if (((entry->lo & 0xfffffff8) != (newlo & 0xfffffff8)) &&
- (entry->hi != newhi) && del)
- return 0;
-
- if (i == HOP_NUMBER) {
- if (!del) {
- printf("ARMD100 FEC: (%s) table section is full\n",
- __func__);
- return -ENOSPC;
- } else {
- return 0;
- }
- }
-
- /*
- * Update the selected entry
- */
- if (del) {
- entry->hi = 0;
- entry->lo = 0;
- } else {
- entry->hi = newhi;
- entry->lo = newlo;
- }
-
- return 0;
-}
-
-/*
- * Create an addressTable entry from MAC address info
- * found in the specifed net_device struct
- *
- * Input : pointer to ethernet interface network device structure
- * Output : N/A
- */
-static void update_hash_table_mac_address(struct armdfec_device *darmdfec,
- u8 *oaddr, u8 *addr)
-{
- u32 mach;
- u32 macl;
-
- /* Delete old entry */
- if (oaddr) {
- mach = (oaddr[0] << 8) | oaddr[1];
- macl = (oaddr[2] << 24) | (oaddr[3] << 16) |
- (oaddr[4] << 8) | oaddr[5];
- add_del_hash_entry(darmdfec, mach, macl, 1, 0, HASH_DELETE);
- }
-
- /* Add new entry */
- mach = (addr[0] << 8) | addr[1];
- macl = (addr[2] << 24) | (addr[3] << 16) | (addr[4] << 8) | addr[5];
- add_del_hash_entry(darmdfec, mach, macl, 1, 0, HASH_ADD);
-}
-
-/* Address Table Initialization */
-static void init_hashtable(struct eth_device *dev)
-{
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct armdfec_reg *regs = darmdfec->regs;
- memset(darmdfec->htpr, 0, HASH_ADDR_TABLE_SIZE);
- writel((u32)darmdfec->htpr, ®s->htpr);
-}
-
-/*
- * This detects PHY chip from address 0-31 by reading PHY status
- * registers. PHY chip can be connected at any of this address.
- */
-static int ethernet_phy_detect(struct eth_device *dev)
-{
- u32 val;
- u16 tmp, mii_status;
- u8 addr;
-
- for (addr = 0; addr < 32; addr++) {
- if (miiphy_read(dev->name, addr, MII_BMSR, &mii_status) != 0)
- /* try next phy */
- continue;
-
- /* invalid MII status. More validation required here... */
- if (mii_status == 0 || mii_status == 0xffff)
- /* try next phy */
- continue;
-
- if (miiphy_read(dev->name, addr, MII_PHYSID1, &tmp) != 0)
- /* try next phy */
- continue;
-
- val = tmp << 16;
- if (miiphy_read(dev->name, addr, MII_PHYSID2, &tmp) != 0)
- /* try next phy */
- continue;
-
- val |= tmp;
-
- if ((val & 0xfffffff0) != 0)
- return addr;
- }
- return -1;
-}
-
-static void armdfec_init_rx_desc_ring(struct armdfec_device *darmdfec)
-{
- struct rx_desc *p_rx_desc;
- int i;
-
- /* initialize the Rx descriptors ring */
- p_rx_desc = darmdfec->p_rxdesc;
- for (i = 0; i < RINGSZ; i++) {
- p_rx_desc->cmd_sts = BUF_OWNED_BY_DMA | RX_EN_INT;
- p_rx_desc->buf_size = PKTSIZE_ALIGN;
- p_rx_desc->byte_cnt = 0;
- p_rx_desc->buf_ptr = darmdfec->p_rxbuf + i * PKTSIZE_ALIGN;
- if (i == (RINGSZ - 1)) {
- p_rx_desc->nxtdesc_p = darmdfec->p_rxdesc;
- } else {
- p_rx_desc->nxtdesc_p = (struct rx_desc *)
- ((u32)p_rx_desc + ARMDFEC_RXQ_DESC_ALIGNED_SIZE);
- p_rx_desc = p_rx_desc->nxtdesc_p;
- }
- }
- darmdfec->p_rxdesc_curr = darmdfec->p_rxdesc;
-}
-
-static int armdfec_init(struct eth_device *dev, struct bd_info *bd)
-{
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct armdfec_reg *regs = darmdfec->regs;
- int phy_adr;
- u32 temp;
-
- armdfec_init_rx_desc_ring(darmdfec);
-
- /* Disable interrupts */
- writel(0, ®s->im);
- writel(0, ®s->ic);
- /* Write to ICR to clear interrupts. */
- writel(0, ®s->iwc);
-
- /*
- * Abort any transmit and receive operations and put DMA
- * in idle state.
- */
- abortdma(dev);
-
- /* Initialize address hash table */
- init_hashtable(dev);
-
- /* SDMA configuration */
- writel(SDCR_BSZ8 | /* Burst size = 32 bytes */
- SDCR_RIFB | /* Rx interrupt on frame */
- SDCR_BLMT | /* Little endian transmit */
- SDCR_BLMR | /* Little endian receive */
- SDCR_RC_MAX_RETRANS, /* Max retransmit count */
- ®s->sdma_conf);
- /* Port Configuration */
- writel(PCR_HS, ®s->pconf); /* Hash size is 1/2kb */
-
- /* Set extended port configuration */
- writel(PCXR_2BSM | /* Two byte suffix aligns IP hdr */
- PCXR_DSCP_EN | /* Enable DSCP in IP */
- PCXR_MFL_1536 | /* Set MTU = 1536 */
- PCXR_FLP | /* do not force link pass */
- PCXR_TX_HIGH_PRI, /* Transmit - high priority queue */
- ®s->pconf_ext);
-
- update_hash_table_mac_address(darmdfec, NULL, dev->enetaddr);
-
- /* Update TX and RX queue descriptor register */
- temp = (u32)®s->txcdp[TXQ];
- writel((u32)darmdfec->p_txdesc, temp);
- temp = (u32)®s->rxfdp[RXQ];
- writel((u32)darmdfec->p_rxdesc, temp);
- temp = (u32)®s->rxcdp[RXQ];
- writel((u32)darmdfec->p_rxdesc_curr, temp);
-
- /* Enable Interrupts */
- writel(ALL_INTS, ®s->im);
-
- /* Enable Ethernet Port */
- setbits_le32(®s->pconf, PCR_EN);
-
- /* Enable RX DMA engine */
- setbits_le32(®s->sdma_cmd, SDMA_CMD_ERD);
-
-#ifdef DEBUG
- eth_dump_regs(dev);
-#endif
-
-#if (defined(CONFIG_MII) || defined(CONFIG_CMD_MII))
-
-#if defined(CONFIG_PHY_BASE_ADR)
- miiphy_write(dev->name, PHY_ADR_REQ, PHY_ADR_REQ, CONFIG_PHY_BASE_ADR);
-#else
- /* Search phy address from range 0-31 */
- phy_adr = ethernet_phy_detect(dev);
- if (phy_adr < 0) {
- printf("ARMD100 FEC: PHY not detected at address range 0-31\n");
- return -1;
- } else {
- debug("ARMD100 FEC: PHY detected at addr %d\n", phy_adr);
- miiphy_write(dev->name, PHY_ADR_REQ, PHY_ADR_REQ, phy_adr);
- }
-#endif
-
-#if defined(CONFIG_SYS_FAULT_ECHO_LINK_DOWN)
- /* Wait up to 5s for the link status */
- for (i = 0; i < 5; i++) {
- u16 phy_adr;
-
- miiphy_read(dev->name, 0xFF, 0xFF, &phy_adr);
- /* Return if we get link up */
- if (miiphy_link(dev->name, phy_adr))
- return 0;
- udelay(1000000);
- }
-
- printf("ARMD100 FEC: No link on %s\n", dev->name);
- return -1;
-#endif
-#endif
- return 0;
-}
-
-static void armdfec_halt(struct eth_device *dev)
-{
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct armdfec_reg *regs = darmdfec->regs;
-
- /* Stop RX DMA */
- clrbits_le32(®s->sdma_cmd, SDMA_CMD_ERD);
-
- /*
- * Abort any transmit and receive operations and put DMA
- * in idle state.
- */
- abortdma(dev);
-
- /* Disable interrupts */
- writel(0, ®s->im);
- writel(0, ®s->ic);
- writel(0, ®s->iwc);
-
- /* Disable Port */
- clrbits_le32(®s->pconf, PCR_EN);
-}
-
-static int armdfec_send(struct eth_device *dev, void *dataptr, int datasize)
-{
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct armdfec_reg *regs = darmdfec->regs;
- struct tx_desc *p_txdesc = darmdfec->p_txdesc;
- void *p = (void *)dataptr;
- int retry = PHY_WAIT_ITERATIONS * PHY_WAIT_MICRO_SECONDS;
- u32 cmd_sts, temp;
-
- /* Copy buffer if it's misaligned */
- if ((u32)dataptr & 0x07) {
- if (datasize > PKTSIZE_ALIGN) {
- printf("ARMD100 FEC: Non-aligned data too large (%d)\n",
- datasize);
- return -1;
- }
- memcpy(darmdfec->p_aligned_txbuf, p, datasize);
- p = darmdfec->p_aligned_txbuf;
- }
-
- p_txdesc->cmd_sts = TX_ZERO_PADDING | TX_GEN_CRC;
- p_txdesc->cmd_sts |= TX_FIRST_DESC | TX_LAST_DESC;
- p_txdesc->cmd_sts |= BUF_OWNED_BY_DMA;
- p_txdesc->cmd_sts |= TX_EN_INT;
- p_txdesc->buf_ptr = p;
- p_txdesc->byte_cnt = datasize;
-
- /* Apply send command using high priority TX queue */
- temp = (u32)®s->txcdp[TXQ];
- writel((u32)p_txdesc, temp);
- writel(SDMA_CMD_TXDL | SDMA_CMD_TXDH | SDMA_CMD_ERD, ®s->sdma_cmd);
-
- /*
- * wait for packet xmit completion
- */
- cmd_sts = readl(&p_txdesc->cmd_sts);
- while (cmd_sts & BUF_OWNED_BY_DMA) {
- /* return fail if error is detected */
- if ((cmd_sts & (TX_ERROR | TX_LAST_DESC)) ==
- (TX_ERROR | TX_LAST_DESC)) {
- printf("ARMD100 FEC: (%s) in xmit packet\n", __func__);
- return -1;
- }
- cmd_sts = readl(&p_txdesc->cmd_sts);
- if (!(retry--)) {
- printf("ARMD100 FEC: (%s) xmit packet timeout!\n",
- __func__);
- return -1;
- }
- }
-
- return 0;
-}
-
-static int armdfec_recv(struct eth_device *dev)
-{
- struct armdfec_device *darmdfec = to_darmdfec(dev);
- struct rx_desc *p_rxdesc_curr = darmdfec->p_rxdesc_curr;
- u32 cmd_sts;
- u32 timeout = 0;
- u32 temp;
-
- /* wait untill rx packet available or timeout */
- do {
- if (timeout < PHY_WAIT_ITERATIONS * PHY_WAIT_MICRO_SECONDS) {
- timeout++;
- } else {
- debug("ARMD100 FEC: %s time out...\n", __func__);
- return -1;
- }
- } while (readl(&p_rxdesc_curr->cmd_sts) & BUF_OWNED_BY_DMA);
-
- if (p_rxdesc_curr->byte_cnt != 0) {
- debug("ARMD100 FEC: %s: Received %d byte Packet @ 0x%x"
- "(cmd_sts= %08x)\n", __func__,
- (u32)p_rxdesc_curr->byte_cnt,
- (u32)p_rxdesc_curr->buf_ptr,
- (u32)p_rxdesc_curr->cmd_sts);
- }
-
- /*
- * In case received a packet without first/last bits on
- * OR the error summary bit is on,
- * the packets needs to be dropeed.
- */
- cmd_sts = readl(&p_rxdesc_curr->cmd_sts);
-
- if ((cmd_sts & (RX_FIRST_DESC | RX_LAST_DESC)) !=
- (RX_FIRST_DESC | RX_LAST_DESC)) {
- printf("ARMD100 FEC: (%s) Dropping packet spread on"
- " multiple descriptors\n", __func__);
- } else if (cmd_sts & RX_ERROR) {
- printf("ARMD100 FEC: (%s) Dropping packet with errors\n",
- __func__);
- } else {
- /* !!! call higher layer processing */
- debug("ARMD100 FEC: (%s) Sending Received packet to"
- " upper layer (net_process_received_packet)\n", __func__);
-
- /*
- * let the upper layer handle the packet, subtract offset
- * as two dummy bytes are added in received buffer see
- * PORT_CONFIG_EXT register bit TWO_Byte_Stuff_Mode bit.
- */
- net_process_received_packet(
- p_rxdesc_curr->buf_ptr + RX_BUF_OFFSET,
- (int)(p_rxdesc_curr->byte_cnt - RX_BUF_OFFSET));
- }
- /*
- * free these descriptors and point next in the ring
- */
- p_rxdesc_curr->cmd_sts = BUF_OWNED_BY_DMA | RX_EN_INT;
- p_rxdesc_curr->buf_size = PKTSIZE_ALIGN;
- p_rxdesc_curr->byte_cnt = 0;
-
- temp = (u32)&darmdfec->p_rxdesc_curr;
- writel((u32)p_rxdesc_curr->nxtdesc_p, temp);
-
- return 0;
-}
-
-int armada100_fec_register(unsigned long base_addr)
-{
- struct armdfec_device *darmdfec;
- struct eth_device *dev;
-
- darmdfec = malloc(sizeof(struct armdfec_device));
- if (!darmdfec)
- goto error;
-
- memset(darmdfec, 0, sizeof(struct armdfec_device));
-
- darmdfec->htpr = memalign(8, HASH_ADDR_TABLE_SIZE);
- if (!darmdfec->htpr)
- goto error1;
-
- darmdfec->p_rxdesc = memalign(PKTALIGN,
- ARMDFEC_RXQ_DESC_ALIGNED_SIZE * RINGSZ + 1);
-
- if (!darmdfec->p_rxdesc)
- goto error1;
-
- darmdfec->p_rxbuf = memalign(PKTALIGN, RINGSZ * PKTSIZE_ALIGN + 1);
- if (!darmdfec->p_rxbuf)
- goto error1;
-
- darmdfec->p_aligned_txbuf = memalign(8, PKTSIZE_ALIGN);
- if (!darmdfec->p_aligned_txbuf)
- goto error1;
-
- darmdfec->p_txdesc = memalign(PKTALIGN, sizeof(struct tx_desc) + 1);
- if (!darmdfec->p_txdesc)
- goto error1;
-
- dev = &darmdfec->dev;
- /* Assign ARMADA100 Fast Ethernet Controller Base Address */
- darmdfec->regs = (void *)base_addr;
-
- /* must be less than sizeof(dev->name) */
- strcpy(dev->name, "armd-fec0");
-
- dev->init = armdfec_init;
- dev->halt = armdfec_halt;
- dev->send = armdfec_send;
- dev->recv = armdfec_recv;
-
- eth_register(dev);
-
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
- int retval;
- struct mii_dev *mdiodev = mdio_alloc();
- if (!mdiodev)
- return -ENOMEM;
- strlcpy(mdiodev->name, dev->name, MDIO_NAME_LEN);
- mdiodev->read = smi_reg_read;
- mdiodev->write = smi_reg_write;
-
- retval = mdio_register(mdiodev);
- if (retval < 0)
- return retval;
-#endif
- return 0;
-
-error1:
- free(darmdfec->p_aligned_txbuf);
- free(darmdfec->p_rxbuf);
- free(darmdfec->p_rxdesc);
- free(darmdfec->htpr);
-error:
- free(darmdfec);
- printf("AMD100 FEC: (%s) Failed to allocate memory\n", __func__);
- return -1;
-}
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2011
- * eInfochips Ltd. <www.einfochips.com>
- * Written-by: Ajay Bhargav <contact@8051projects.net>
- *
- * (C) Copyright 2010
- * Marvell Semiconductor <www.marvell.com>
- * Contributor: Mahavir Jain <mjain@marvell.com>
- */
-
-#ifndef __ARMADA100_FEC_H__
-#define __ARMADA100_FEC_H__
-
-#define PORT_NUM 0x0
-
-/* RX & TX descriptor command */
-#define BUF_OWNED_BY_DMA (1<<31)
-
-/* RX descriptor status */
-#define RX_EN_INT (1<<23)
-#define RX_FIRST_DESC (1<<17)
-#define RX_LAST_DESC (1<<16)
-#define RX_ERROR (1<<15)
-
-/* TX descriptor command */
-#define TX_EN_INT (1<<23)
-#define TX_GEN_CRC (1<<22)
-#define TX_ZERO_PADDING (1<<18)
-#define TX_FIRST_DESC (1<<17)
-#define TX_LAST_DESC (1<<16)
-#define TX_ERROR (1<<15)
-
-/* smi register */
-#define SMI_BUSY (1<<28) /* 0 - Write, 1 - Read */
-#define SMI_R_VALID (1<<27) /* 0 - Write, 1 - Read */
-#define SMI_OP_W (0<<26) /* Write operation */
-#define SMI_OP_R (1<<26) /* Read operation */
-
-#define HASH_ADD 0
-#define HASH_DELETE 1
-#define HASH_ADDR_TABLE_SIZE 0x4000 /* 16K (1/2K address - PCR_HS == 1) */
-#define HOP_NUMBER 12
-
-#define PHY_WAIT_ITERATIONS 1000 /* 1000 iterations * 10uS = 10mS max */
-#define PHY_WAIT_MICRO_SECONDS 10
-
-#define ETH_HW_IP_ALIGN 2 /* hw aligns IP header */
-#define ETH_EXTRA_HEADER (6+6+2+4)
- /* dest+src addr+protocol id+crc */
-#define MAX_PKT_SIZE 1536
-
-
-/* Bit definitions of the SDMA Config Reg */
-#define SDCR_BSZ_OFF 12
-#define SDCR_BSZ8 (3<<SDCR_BSZ_OFF)
-#define SDCR_BSZ4 (2<<SDCR_BSZ_OFF)
-#define SDCR_BSZ2 (1<<SDCR_BSZ_OFF)
-#define SDCR_BSZ1 (0<<SDCR_BSZ_OFF)
-#define SDCR_BLMR (1<<6)
-#define SDCR_BLMT (1<<7)
-#define SDCR_RIFB (1<<9)
-#define SDCR_RC_OFF 2
-#define SDCR_RC_MAX_RETRANS (0xf << SDCR_RC_OFF)
-
-/* SDMA_CMD */
-#define SDMA_CMD_AT (1<<31)
-#define SDMA_CMD_TXDL (1<<24)
-#define SDMA_CMD_TXDH (1<<23)
-#define SDMA_CMD_AR (1<<15)
-#define SDMA_CMD_ERD (1<<7)
-
-
-/* Bit definitions of the Port Config Reg */
-#define PCR_HS (1<<12)
-#define PCR_EN (1<<7)
-#define PCR_PM (1<<0)
-
-/* Bit definitions of the Port Config Extend Reg */
-#define PCXR_2BSM (1<<28)
-#define PCXR_DSCP_EN (1<<21)
-#define PCXR_MFL_1518 (0<<14)
-#define PCXR_MFL_1536 (1<<14)
-#define PCXR_MFL_2048 (2<<14)
-#define PCXR_MFL_64K (3<<14)
-#define PCXR_FLP (1<<11)
-#define PCXR_PRIO_TX_OFF 3
-#define PCXR_TX_HIGH_PRI (7<<PCXR_PRIO_TX_OFF)
-
-/*
- * * Bit definitions of the Interrupt Cause Reg
- * * and Interrupt MASK Reg is the same
- * */
-#define ICR_RXBUF (1<<0)
-#define ICR_TXBUF_H (1<<2)
-#define ICR_TXBUF_L (1<<3)
-#define ICR_TXEND_H (1<<6)
-#define ICR_TXEND_L (1<<7)
-#define ICR_RXERR (1<<8)
-#define ICR_TXERR_H (1<<10)
-#define ICR_TXERR_L (1<<11)
-#define ICR_TX_UDR (1<<13)
-#define ICR_MII_CH (1<<28)
-
-#define ALL_INTS (ICR_TXBUF_H | ICR_TXBUF_L | ICR_TX_UDR |\
- ICR_TXERR_H | ICR_TXERR_L |\
- ICR_TXEND_H | ICR_TXEND_L |\
- ICR_RXBUF | ICR_RXERR | ICR_MII_CH)
-
-#define PHY_MASK 0x0000001f
-
-#define to_darmdfec(_kd) container_of(_kd, struct armdfec_device, dev)
-/* Size of a Tx/Rx descriptor used in chain list data structure */
-#define ARMDFEC_RXQ_DESC_ALIGNED_SIZE \
- (((sizeof(struct rx_desc) / PKTALIGN) + 1) * PKTALIGN)
-
-#define RX_BUF_OFFSET 0x2
-#define RXQ 0x0 /* RX Queue 0 */
-#define TXQ 0x1 /* TX Queue 1 */
-
-struct addr_table_entry_t {
- u32 lo;
- u32 hi;
-};
-
-/* Bit fields of a Hash Table Entry */
-enum hash_table_entry {
- HTEVALID = 1,
- HTESKIP = 2,
- HTERD = 4,
- HTERDBIT = 2
-};
-
-struct tx_desc {
- u32 cmd_sts; /* Command/status field */
- u16 reserved;
- u16 byte_cnt; /* buffer byte count */
- u8 *buf_ptr; /* pointer to buffer for this descriptor */
- struct tx_desc *nextdesc_p; /* Pointer to next descriptor */
-};
-
-struct rx_desc {
- u32 cmd_sts; /* Descriptor command status */
- u16 byte_cnt; /* Descriptor buffer byte count */
- u16 buf_size; /* Buffer size */
- u8 *buf_ptr; /* Descriptor buffer pointer */
- struct rx_desc *nxtdesc_p; /* Next descriptor pointer */
-};
-
-/*
- * Armada100 Fast Ethernet controller Registers
- * Refer Datasheet Appendix A.22
- */
-struct armdfec_reg {
- u32 phyadr; /* PHY Address */
- u32 pad1[3];
- u32 smi; /* SMI */
- u32 pad2[0xFB];
- u32 pconf; /* Port configuration */
- u32 pad3;
- u32 pconf_ext; /* Port configuration extend */
- u32 pad4;
- u32 pcmd; /* Port Command */
- u32 pad5;
- u32 pstatus; /* Port Status */
- u32 pad6;
- u32 spar; /* Serial Parameters */
- u32 pad7;
- u32 htpr; /* Hash table pointer */
- u32 pad8;
- u32 fcsal; /* Flow control source address low */
- u32 pad9;
- u32 fcsah; /* Flow control source address high */
- u32 pad10;
- u32 sdma_conf; /* SDMA configuration */
- u32 pad11;
- u32 sdma_cmd; /* SDMA command */
- u32 pad12;
- u32 ic; /* Interrupt cause */
- u32 iwc; /* Interrupt write to clear */
- u32 im; /* Interrupt mask */
- u32 pad13;
- u32 *eth_idscpp[4]; /* Eth0 IP Differentiated Services Code
- Point to Priority 0 Low */
- u32 eth_vlan_p; /* Eth0 VLAN Priority Tag to Priority */
- u32 pad14[3];
- struct rx_desc *rxfdp[4]; /* Ethernet First Rx Descriptor
- Pointer */
- u32 pad15[4];
- struct rx_desc *rxcdp[4]; /* Ethernet Current Rx Descriptor
- Pointer */
- u32 pad16[0x0C];
- struct tx_desc *txcdp[2]; /* Ethernet Current Tx Descriptor
- Pointer */
-};
-
-struct armdfec_device {
- struct eth_device dev;
- struct armdfec_reg *regs;
- struct tx_desc *p_txdesc;
- struct rx_desc *p_rxdesc;
- struct rx_desc *p_rxdesc_curr;
- u8 *p_rxbuf;
- u8 *p_aligned_txbuf;
- u8 *htpr; /* hash pointer */
-};
-
-#endif /* __ARMADA100_FEC_H__ */
projects / platform / kernel / u-boot.git / commitdiff