CONFIG_SENSORS_PCF8574=y
# CONFIG_PCF8575 is not set
CONFIG_SENSORS_PCF8591=y
-CONFIG_SENSORS_MAX6875=y
+CONFIG_EEPROM_MAX6875=y
# CONFIG_SENSORS_TSL2550 is not set
CONFIG_I2C_DEBUG_CORE=y
CONFIG_I2C_DEBUG_ALGO=y
CONFIG_SENSORS_PCF8574=m
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
-CONFIG_SENSORS_MAX6875=m
+CONFIG_EEPROM_MAX6875=m
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
# CONFIG_TPS65010 is not set
-CONFIG_SENSORS_MAX6875=m
+CONFIG_EEPROM_MAX6875=m
CONFIG_SENSORS_TSL2550=m
CONFIG_MCU_MPC8349EMITX=m
# CONFIG_I2C_DEBUG_CORE is not set
This driver is deprecated and will be dropped soon. Use
drivers/gpio/pca953x.c instead.
-config SENSORS_MAX6875
- tristate "Maxim MAX6875 Power supply supervisor"
- depends on EXPERIMENTAL
- help
- If you say yes here you get support for the Maxim MAX6875
- EEPROM-programmable, quad power-supply sequencer/supervisor.
-
- This provides an interface to program the EEPROM and reset the chip.
-
- This driver also supports the Maxim MAX6874 hex power-supply
- sequencer/supervisor if found at a compatible address.
-
- This driver can also be built as a module. If so, the module
- will be called max6875.
-
config SENSORS_TSL2550
tristate "Taos TSL2550 ambient light sensor"
depends on EXPERIMENTAL
#
obj-$(CONFIG_DS1682) += ds1682.o
-obj-$(CONFIG_SENSORS_MAX6875) += max6875.o
obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o
obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o
obj-$(CONFIG_PCF8575) += pcf8575.o
This driver can also be built as a module. If so, the module
will be called eeprom.
+config EEPROM_MAX6875
+ tristate "Maxim MAX6874/5 power supply supervisor"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get read-only support for the user EEPROM of
+ the Maxim MAX6874/5 EEPROM-programmable, quad power-supply
+ sequencer/supervisor.
+
+ All other features of this chip should be accessed via i2c-dev.
+
+ This driver can also be built as a module. If so, the module
+ will be called max6875.
+
+
config EEPROM_93CX6
tristate "EEPROM 93CX6 support"
help
obj-$(CONFIG_EEPROM_AT24) += at24.o
obj-$(CONFIG_EEPROM_AT25) += at25.o
obj-$(CONFIG_EEPROM_LEGACY) += eeprom.o
+obj-$(CONFIG_EEPROM_MAX6875) += max6875.o
obj-$(CONFIG_EEPROM_93CX6) += eeprom_93cx6.o
Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
- Based on i2c/chips/eeprom.c
+ Based on eeprom.c
The MAX6875 has a bank of registers and two banks of EEPROM.
Address ranges are defined as follows: