// SPDX-License-Identifier: GPL-2.0+
/*
- * Motorcomm 8511/8521/8531S PHY driver.
+ * Motorcomm 8511/8521/8531/8531S PHY driver.
*
* Author: Peter Geis <pgwipeout@gmail.com>
* Author: Frank <Frank.Sae@motor-comm.com>
#define PHY_ID_YT8511 0x0000010a
#define PHY_ID_YT8521 0x0000011a
+#define PHY_ID_YT8531 0x4f51e91b
#define PHY_ID_YT8531S 0x4f51e91a
/* YT8521/YT8531S Register Overview
return phy_restore_page(phydev, old_page, ret);
}
+static int yt8531_set_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol)
+{
+ const u16 mac_addr_reg[] = {
+ YTPHY_WOL_MACADDR2_REG,
+ YTPHY_WOL_MACADDR1_REG,
+ YTPHY_WOL_MACADDR0_REG,
+ };
+ const u8 *mac_addr;
+ u16 mask, val;
+ int ret;
+ u8 i;
+
+ if (wol->wolopts & WAKE_MAGIC) {
+ mac_addr = phydev->attached_dev->dev_addr;
+
+ /* Store the device address for the magic packet */
+ for (i = 0; i < 3; i++) {
+ ret = ytphy_write_ext_with_lock(phydev, mac_addr_reg[i],
+ ((mac_addr[i * 2] << 8)) |
+ (mac_addr[i * 2 + 1]));
+ if (ret < 0)
+ return ret;
+ }
+
+ /* Enable WOL feature */
+ mask = YTPHY_WCR_PULSE_WIDTH_MASK | YTPHY_WCR_INTR_SEL;
+ val = YTPHY_WCR_ENABLE | YTPHY_WCR_INTR_SEL;
+ val |= YTPHY_WCR_TYPE_PULSE | YTPHY_WCR_PULSE_WIDTH_672MS;
+ ret = ytphy_modify_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG,
+ mask, val);
+ if (ret < 0)
+ return ret;
+
+ /* Enable WOL interrupt */
+ ret = phy_modify(phydev, YTPHY_INTERRUPT_ENABLE_REG, 0,
+ YTPHY_IER_WOL);
+ if (ret < 0)
+ return ret;
+ } else {
+ /* Disable WOL feature */
+ mask = YTPHY_WCR_ENABLE | YTPHY_WCR_INTR_SEL;
+ ret = ytphy_modify_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG,
+ mask, 0);
+
+ /* Disable WOL interrupt */
+ ret = phy_modify(phydev, YTPHY_INTERRUPT_ENABLE_REG,
+ YTPHY_IER_WOL, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
static int yt8511_read_page(struct phy_device *phydev)
{
return __phy_read(phydev, YT8511_PAGE_SELECT);
return ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG, mask, val);
}
+static int ytphy_rgmii_clk_delay_config_with_lock(struct phy_device *phydev)
+{
+ int ret;
+
+ phy_lock_mdio_bus(phydev);
+ ret = ytphy_rgmii_clk_delay_config(phydev);
+ phy_unlock_mdio_bus(phydev);
+
+ return ret;
+}
+
/**
* yt8521_probe() - read chip config then set suitable polling_mode
* @phydev: a pointer to a &struct phy_device
val);
}
+static int yt8531_probe(struct phy_device *phydev)
+{
+ struct device_node *node = phydev->mdio.dev.of_node;
+ u16 mask, val;
+ u32 freq;
+
+ if (of_property_read_u32(node, "motorcomm,clk-out-frequency-hz", &freq))
+ freq = YTPHY_DTS_OUTPUT_CLK_DIS;
+
+ switch (freq) {
+ case YTPHY_DTS_OUTPUT_CLK_DIS:
+ mask = YT8531_SCR_SYNCE_ENABLE;
+ val = 0;
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_25M:
+ mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK |
+ YT8531_SCR_CLK_FRE_SEL_125M;
+ val = YT8531_SCR_SYNCE_ENABLE |
+ FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+ YT8531_SCR_CLK_SRC_REF_25M);
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_125M:
+ mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK |
+ YT8531_SCR_CLK_FRE_SEL_125M;
+ val = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_FRE_SEL_125M |
+ FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+ YT8531_SCR_CLK_SRC_PLL_125M);
+ break;
+ default:
+ phydev_warn(phydev, "Freq err:%u\n", freq);
+ return -EINVAL;
+ }
+
+ return ytphy_modify_ext_with_lock(phydev, YTPHY_SYNCE_CFG_REG, mask,
+ val);
+}
+
/**
* ytphy_utp_read_lpa() - read LPA then setup lp_advertising for utp
* @phydev: a pointer to a &struct phy_device
return phy_restore_page(phydev, old_page, ret);
}
+static int yt8531_config_init(struct phy_device *phydev)
+{
+ struct device_node *node = phydev->mdio.dev.of_node;
+ int ret;
+
+ ret = ytphy_rgmii_clk_delay_config_with_lock(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (of_property_read_bool(node, "motorcomm,auto-sleep-disabled")) {
+ /* disable auto sleep */
+ ret = ytphy_modify_ext_with_lock(phydev,
+ YT8521_EXTREG_SLEEP_CONTROL1_REG,
+ YT8521_ESC1R_SLEEP_SW, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ if (of_property_read_bool(node, "motorcomm,keep-pll-enabled")) {
+ /* enable RXC clock when no wire plug */
+ ret = ytphy_modify_ext_with_lock(phydev,
+ YT8521_CLOCK_GATING_REG,
+ YT8521_CGR_RX_CLK_EN, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * yt8531_link_change_notify() - Adjust the tx clock direction according to
+ * the current speed and dts config.
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * NOTE: This function is only used to adapt to VF2 with JH7110 SoC. Please
+ * keep "motorcomm,tx-clk-adj-enabled" not exist in dts when the soc is not
+ * JH7110.
+ */
+static void yt8531_link_change_notify(struct phy_device *phydev)
+{
+ struct device_node *node = phydev->mdio.dev.of_node;
+ bool tx_clk_adj_enabled = false;
+ bool tx_clk_1000_inverted;
+ bool tx_clk_100_inverted;
+ bool tx_clk_10_inverted;
+ u16 val = 0;
+ int ret;
+
+ if (of_property_read_bool(node, "motorcomm,tx-clk-adj-enabled"))
+ tx_clk_adj_enabled = true;
+
+ if (!tx_clk_adj_enabled)
+ return;
+
+ if (of_property_read_bool(node, "motorcomm,tx-clk-10-inverted"))
+ tx_clk_10_inverted = true;
+ if (of_property_read_bool(node, "motorcomm,tx-clk-100-inverted"))
+ tx_clk_100_inverted = true;
+ if (of_property_read_bool(node, "motorcomm,tx-clk-1000-inverted"))
+ tx_clk_1000_inverted = true;
+
+ if (phydev->speed < 0)
+ return;
+
+ switch (phydev->speed) {
+ case SPEED_1000:
+ if (tx_clk_1000_inverted)
+ val = YT8521_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ case SPEED_100:
+ if (tx_clk_100_inverted)
+ val = YT8521_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ case SPEED_10:
+ if (tx_clk_10_inverted)
+ val = YT8521_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ default:
+ return;
+ }
+
+ ret = ytphy_modify_ext_with_lock(phydev, YT8521_RGMII_CONFIG1_REG,
+ YT8521_RC1R_TX_CLK_SEL_INVERTED, val);
+ if (ret < 0)
+ phydev_warn(phydev, "Modify TX_CLK_SEL err:%d\n", ret);
+}
+
/**
* yt8521_prepare_fiber_features() - A small helper function that setup
* fiber's features.
.suspend = yt8521_suspend,
.resume = yt8521_resume,
},
+ {
+ PHY_ID_MATCH_EXACT(PHY_ID_YT8531),
+ .name = "YT8531 Gigabit Ethernet",
+ .probe = yt8531_probe,
+ .config_init = yt8531_config_init,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .get_wol = ytphy_get_wol,
+ .set_wol = yt8531_set_wol,
+ .link_change_notify = yt8531_link_change_notify,
+ },
{
PHY_ID_MATCH_EXACT(PHY_ID_YT8531S),
.name = "YT8531S Gigabit Ethernet",
module_phy_driver(motorcomm_phy_drvs);
-MODULE_DESCRIPTION("Motorcomm 8511/8521/8531S PHY driver");
+MODULE_DESCRIPTION("Motorcomm 8511/8521/8531/8531S PHY driver");
MODULE_AUTHOR("Peter Geis");
MODULE_AUTHOR("Frank");
MODULE_LICENSE("GPL");
static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = {
{ PHY_ID_MATCH_EXACT(PHY_ID_YT8511) },
{ PHY_ID_MATCH_EXACT(PHY_ID_YT8521) },
+ { PHY_ID_MATCH_EXACT(PHY_ID_YT8531) },
{ PHY_ID_MATCH_EXACT(PHY_ID_YT8531S) },
{ /* sentinel */ }
};