static unsigned int ir_debug;
module_param(ir_debug, int, 0644);
-MODULE_PARM_DESC(ir_debug, "enable debug message [IR]");
+MODULE_PARM_DESC(ir_debug, "debug message level");
static unsigned int enable_ir = 1;
module_param(enable_ir, int, 0644);
MODULE_PARM_DESC(enable_ir, "enable ir (default is enable)");
-/* number of 50ms for ON-OFF-ON power led */
-/* show IR activity */
-#define PWLED_OFF 2
+static unsigned int ir_clock_mhz = 12;
+module_param(ir_clock_mhz, int, 0644);
+MODULE_PARM_DESC(enable_ir, "ir clock, in MHz");
+
+#define URB_SUBMIT_DELAY 100 /* ms - Delay to submit an URB request on retrial and init */
+#define URB_INT_LED_DELAY 100 /* ms - Delay to turn led on again on int mode */
#undef dprintk
-#define dprintk(fmt, arg...) \
- if (ir_debug) { \
+#define dprintk(level, fmt, arg...) do {\
+ if (ir_debug >= level) \
printk(KERN_DEBUG "%s/ir: " fmt, ir->name , ## arg); \
- }
+ } while (0)
struct tm6000_ir_poll_result {
u16 rc_data;
int polling;
struct delayed_work work;
u8 wait:1;
- u8 key:1;
- u8 pwled:1;
- u8 pwledcnt;
+ u8 pwled:2;
+ u8 submit_urb:1;
u16 key_addr;
struct urb *int_urb;
- u8 *urb_data;
-
- int (*get_key) (struct tm6000_IR *, struct tm6000_ir_poll_result *);
/* IR device properties */
u64 rc_type;
};
-
void tm6000_ir_wait(struct tm6000_core *dev, u8 state)
{
struct tm6000_IR *ir = dev->ir;
if (!dev->ir)
return;
+ dprintk(2, "%s: %i\n",__func__, ir->wait);
+
if (state)
ir->wait = 1;
else
ir->wait = 0;
}
-
static int tm6000_ir_config(struct tm6000_IR *ir)
{
struct tm6000_core *dev = ir->dev;
- u8 buf[10];
- int rc;
+ u32 pulse = 0, leader = 0;
+
+ dprintk(2, "%s\n",__func__);
+
+ /*
+ * The IR decoder supports RC-5 or NEC, with a configurable timing.
+ * The timing configuration there is not that accurate, as it uses
+ * approximate values. The NEC spec mentions a 562.5 unit period,
+ * and RC-5 uses a 888.8 period.
+ * Currently, driver assumes a clock provided by a 12 MHz XTAL, but
+ * a modprobe parameter can adjust it.
+ * Adjustments are required for other timings.
+ * It seems that the 900ms timing for NEC is used to detect a RC-5
+ * IR, in order to discard such decoding
+ */
switch (ir->rc_type) {
case RC_TYPE_NEC:
- /* Setup IR decoder for NEC standard 12MHz system clock */
- /* IR_LEADER_CNT = 0.9ms */
- tm6000_set_reg(dev, TM6010_REQ07_RDC_IR_LEADER1, 0xaa);
- tm6000_set_reg(dev, TM6010_REQ07_RDD_IR_LEADER0, 0x30);
- /* IR_PULSE_CNT = 0.7ms */
- tm6000_set_reg(dev, TM6010_REQ07_RDE_IR_PULSE_CNT1, 0x20);
- tm6000_set_reg(dev, TM6010_REQ07_RDF_IR_PULSE_CNT0, 0xd0);
- /* Remote WAKEUP = enable */
- tm6000_set_reg(dev, TM6010_REQ07_RE5_REMOTE_WAKEUP, 0xfe);
- /* IR_WKUP_SEL = Low byte in decoded IR data */
- tm6000_set_reg(dev, TM6010_REQ07_RDA_IR_WAKEUP_SEL, 0xff);
- /* IR_WKU_ADD code */
- tm6000_set_reg(dev, TM6010_REQ07_RDB_IR_WAKEUP_ADD, 0xff);
- tm6000_flash_led(dev, 0);
- msleep(100);
- tm6000_flash_led(dev, 1);
+ leader = 900; /* ms */
+ pulse = 700; /* ms - the actual value would be 562 */
break;
default:
- /* hack */
- buf[0] = 0xff;
- buf[1] = 0xff;
- buf[2] = 0xf2;
- buf[3] = 0x2b;
- buf[4] = 0x20;
- buf[5] = 0x35;
- buf[6] = 0x60;
- buf[7] = 0x04;
- buf[8] = 0xc0;
- buf[9] = 0x08;
-
- rc = tm6000_read_write_usb(dev, USB_DIR_OUT | USB_TYPE_VENDOR |
- USB_RECIP_DEVICE, REQ_00_SET_IR_VALUE, 0, 0, buf, 0x0a);
- msleep(100);
-
- if (rc < 0) {
- printk(KERN_INFO "IR configuration failed");
- return rc;
- }
+ case RC_TYPE_RC5:
+ leader = 900; /* ms - from the NEC decoding */
+ pulse = 1780; /* ms - The actual value would be 1776 */
break;
}
+ pulse = ir_clock_mhz * pulse;
+ leader = ir_clock_mhz * leader;
+ if (ir->rc_type == RC_TYPE_NEC)
+ leader = leader | 0x8000;
+
+ dprintk(2, "%s: %s, %d MHz, leader = 0x%04x, pulse = 0x%06x \n",
+ __func__,
+ (ir->rc_type == RC_TYPE_NEC) ? "NEC" : "RC-5",
+ ir_clock_mhz, leader, pulse);
+
+ /* Remote WAKEUP = enable, normal mode, from IR decoder output */
+ tm6000_set_reg(dev, TM6010_REQ07_RE5_REMOTE_WAKEUP, 0xfe);
+
+ /* Enable IR reception on non-busrt mode */
+ tm6000_set_reg(dev, TM6010_REQ07_RD8_IR, 0x2f);
+
+ /* IR_WKUP_SEL = Low byte in decoded IR data */
+ tm6000_set_reg(dev, TM6010_REQ07_RDA_IR_WAKEUP_SEL, 0xff);
+ /* IR_WKU_ADD code */
+ tm6000_set_reg(dev, TM6010_REQ07_RDB_IR_WAKEUP_ADD, 0xff);
+
+ tm6000_set_reg(dev, TM6010_REQ07_RDC_IR_LEADER1, leader >> 8);
+ tm6000_set_reg(dev, TM6010_REQ07_RDD_IR_LEADER0, leader);
+
+ tm6000_set_reg(dev, TM6010_REQ07_RDE_IR_PULSE_CNT1, pulse >> 8);
+ tm6000_set_reg(dev, TM6010_REQ07_RDF_IR_PULSE_CNT0, pulse);
+
+ if (!ir->polling)
+ tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 0);
+ else
+ tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 1);
+ msleep(10);
+
+ /* Shows that IR is working via the LED */
+ tm6000_flash_led(dev, 0);
+ msleep(100);
+ tm6000_flash_led(dev, 1);
+ ir->pwled = 1;
+
return 0;
}
{
struct tm6000_core *dev = urb->context;
struct tm6000_IR *ir = dev->ir;
+ struct tm6000_ir_poll_result poll_result;
+ char *buf;
int rc;
- if (urb->status != 0)
- printk(KERN_INFO "not ready\n");
- else if (urb->actual_length > 0) {
- memcpy(ir->urb_data, urb->transfer_buffer, urb->actual_length);
+ dprintk(2, "%s\n",__func__);
+ if (urb->status < 0 || urb->actual_length <= 0) {
+ printk(KERN_INFO "tm6000: IR URB failure: status: %i, length %i\n",
+ urb->status, urb->actual_length);
+ ir->submit_urb = 1;
+ schedule_delayed_work(&ir->work, msecs_to_jiffies(URB_SUBMIT_DELAY));
+ return;
+ }
+ buf = urb->transfer_buffer;
- dprintk("data %02x %02x %02x %02x\n", ir->urb_data[0],
- ir->urb_data[1], ir->urb_data[2], ir->urb_data[3]);
+ if (ir_debug)
+ print_hex_dump(KERN_DEBUG, "tm6000: IR data: ",
+ DUMP_PREFIX_OFFSET,16, 1,
+ buf, urb->actual_length, false);
- ir->key = 1;
- }
+ poll_result.rc_data = buf[0];
+ if (urb->actual_length > 1)
+ poll_result.rc_data |= buf[1] << 8;
+
+ dprintk(1, "%s, scancode: 0x%04x\n",__func__, poll_result.rc_data);
+ rc_keydown(ir->rc, poll_result.rc_data, 0);
rc = usb_submit_urb(urb, GFP_ATOMIC);
+ /*
+ * Flash the led. We can't do it here, as it is running on IRQ context.
+ * So, use the scheduler to do it, in a few ms.
+ */
+ ir->pwled = 2;
+ schedule_delayed_work(&ir->work, msecs_to_jiffies(10));
}
-static int default_polling_getkey(struct tm6000_IR *ir,
- struct tm6000_ir_poll_result *poll_result)
+static void tm6000_ir_handle_key(struct work_struct *work)
{
+ struct tm6000_IR *ir = container_of(work, struct tm6000_IR, work.work);
struct tm6000_core *dev = ir->dev;
+ struct tm6000_ir_poll_result poll_result;
int rc;
u8 buf[2];
- if (ir->wait && !&dev->int_in)
- return 0;
-
- if (&dev->int_in) {
- switch (ir->rc_type) {
- case RC_TYPE_RC5:
- poll_result->rc_data = ir->urb_data[0];
- break;
- case RC_TYPE_NEC:
- switch (dev->model) {
- case 10:
- case 11:
- case 14:
- case 15:
- if (ir->urb_data[1] ==
- ((ir->key_addr >> 8) & 0xff)) {
- poll_result->rc_data =
- ir->urb_data[0]
- | ir->urb_data[1] << 8;
- }
- break;
- default:
- poll_result->rc_data = ir->urb_data[0]
- | ir->urb_data[1] << 8;
- }
- break;
- default:
- poll_result->rc_data = ir->urb_data[0]
- | ir->urb_data[1] << 8;
- break;
- }
- } else {
- tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 0);
- msleep(10);
- tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 1);
- msleep(10);
-
- if (ir->rc_type == RC_TYPE_RC5) {
- rc = tm6000_read_write_usb(dev, USB_DIR_IN |
- USB_TYPE_VENDOR | USB_RECIP_DEVICE,
- REQ_02_GET_IR_CODE, 0, 0, buf, 1);
-
- msleep(10);
-
- dprintk("read data=%02x\n", buf[0]);
- if (rc < 0)
- return rc;
+ if (ir->wait)
+ return;
- poll_result->rc_data = buf[0];
- } else {
- rc = tm6000_read_write_usb(dev, USB_DIR_IN |
- USB_TYPE_VENDOR | USB_RECIP_DEVICE,
- REQ_02_GET_IR_CODE, 0, 0, buf, 2);
+ dprintk(3, "%s\n",__func__);
- msleep(10);
+ rc = tm6000_read_write_usb(dev, USB_DIR_IN |
+ USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ REQ_02_GET_IR_CODE, 0, 0, buf, 2);
+ if (rc < 0)
+ return;
- dprintk("read data=%04x\n", buf[0] | buf[1] << 8);
- if (rc < 0)
- return rc;
+ if (rc > 1)
+ poll_result.rc_data = buf[0] | buf[1] << 8;
+ else
+ poll_result.rc_data = buf[0];
- poll_result->rc_data = buf[0] | buf[1] << 8;
+ /* Check if something was read */
+ if ((poll_result.rc_data & 0xff) == 0xff) {
+ if (!ir->pwled) {
+ tm6000_flash_led(dev, 1);
+ ir->pwled = 1;
}
- if ((poll_result->rc_data & 0x00ff) != 0xff)
- ir->key = 1;
+ return;
}
- return 0;
+
+ dprintk(1, "%s, scancode: 0x%04x\n",__func__, poll_result.rc_data);
+ rc_keydown(ir->rc, poll_result.rc_data, 0);
+ tm6000_flash_led(dev, 0);
+ ir->pwled = 0;
+
+ /* Re-schedule polling */
+ schedule_delayed_work(&ir->work, msecs_to_jiffies(ir->polling));
}
-static void tm6000_ir_handle_key(struct tm6000_IR *ir)
+static void tm6000_ir_int_work(struct work_struct *work)
{
+ struct tm6000_IR *ir = container_of(work, struct tm6000_IR, work.work);
struct tm6000_core *dev = ir->dev;
- int result;
- struct tm6000_ir_poll_result poll_result;
+ int rc;
- /* read the registers containing the IR status */
- result = ir->get_key(ir, &poll_result);
- if (result < 0) {
- printk(KERN_INFO "ir->get_key() failed %d\n", result);
- return;
- }
+ dprintk(3, "%s, submit_urb = %d, pwled = %d\n",__func__, ir->submit_urb,
+ ir->pwled);
- if (ir->pwled) {
- if (ir->pwledcnt >= PWLED_OFF) {
- ir->pwled = 0;
- ir->pwledcnt = 0;
- tm6000_flash_led(dev, 1);
- } else
- ir->pwledcnt += 1;
+ if (ir->submit_urb) {
+ dprintk(3, "Resubmit urb\n");
+ tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 0);
+
+ rc = usb_submit_urb(ir->int_urb, GFP_ATOMIC);
+ if (rc < 0) {
+ printk(KERN_ERR "tm6000: Can't submit an IR interrupt. Error %i\n",
+ rc);
+ /* Retry in 100 ms */
+ schedule_delayed_work(&ir->work, msecs_to_jiffies(URB_SUBMIT_DELAY));
+ return;
+ }
+ ir->submit_urb = 0;
}
- if (ir->key) {
- dprintk("ir->get_key result data=%04x\n", poll_result.rc_data);
- rc_keydown(ir->rc, poll_result.rc_data, 0);
- ir->key = 0;
- ir->pwled = 1;
- ir->pwledcnt = 0;
+ /* Led is enabled only if USB submit doesn't fail */
+ if (ir->pwled == 2) {
tm6000_flash_led(dev, 0);
+ ir->pwled = 0;
+ schedule_delayed_work(&ir->work, msecs_to_jiffies(URB_INT_LED_DELAY));
+ } else if (!ir->pwled) {
+ tm6000_flash_led(dev, 1);
+ ir->pwled = 1;
}
- return;
-}
-
-static void tm6000_ir_work(struct work_struct *work)
-{
- struct tm6000_IR *ir = container_of(work, struct tm6000_IR, work.work);
-
- tm6000_ir_handle_key(ir);
- schedule_delayed_work(&ir->work, msecs_to_jiffies(ir->polling));
}
static int tm6000_ir_start(struct rc_dev *rc)
{
struct tm6000_IR *ir = rc->priv;
- INIT_DELAYED_WORK(&ir->work, tm6000_ir_work);
+ dprintk(2, "%s\n",__func__);
+
schedule_delayed_work(&ir->work, 0);
return 0;
{
struct tm6000_IR *ir = rc->priv;
+ dprintk(2, "%s\n",__func__);
+
cancel_delayed_work_sync(&ir->work);
}
if (!ir)
return 0;
+ dprintk(2, "%s\n",__func__);
+
if ((rc->rc_map.scan) && (rc_type == RC_TYPE_NEC))
ir->key_addr = ((rc->rc_map.scan[0].scancode >> 8) & 0xffff);
- ir->get_key = default_polling_getkey;
ir->rc_type = rc_type;
tm6000_ir_config(ir);
return 0;
}
-int tm6000_ir_int_start(struct tm6000_core *dev)
+static int __tm6000_ir_int_start(struct rc_dev *rc)
{
- struct tm6000_IR *ir = dev->ir;
+ struct tm6000_IR *ir = rc->priv;
+ struct tm6000_core *dev = ir->dev;
int pipe, size;
int err = -ENOMEM;
-
if (!ir)
return -ENODEV;
- ir->int_urb = usb_alloc_urb(0, GFP_KERNEL);
+ dprintk(2, "%s\n",__func__);
+
+ ir->int_urb = usb_alloc_urb(0, GFP_ATOMIC);
if (!ir->int_urb)
return -ENOMEM;
& USB_ENDPOINT_NUMBER_MASK);
size = usb_maxpacket(dev->udev, pipe, usb_pipeout(pipe));
- dprintk("IR max size: %d\n", size);
+ dprintk(1, "IR max size: %d\n", size);
- ir->int_urb->transfer_buffer = kzalloc(size, GFP_KERNEL);
+ ir->int_urb->transfer_buffer = kzalloc(size, GFP_ATOMIC);
if (ir->int_urb->transfer_buffer == NULL) {
usb_free_urb(ir->int_urb);
return err;
}
- dprintk("int interval: %d\n", dev->int_in.endp->desc.bInterval);
+ dprintk(1, "int interval: %d\n", dev->int_in.endp->desc.bInterval);
+
usb_fill_int_urb(ir->int_urb, dev->udev, pipe,
ir->int_urb->transfer_buffer, size,
tm6000_ir_urb_received, dev,
dev->int_in.endp->desc.bInterval);
- err = usb_submit_urb(ir->int_urb, GFP_ATOMIC);
- if (err) {
- kfree(ir->int_urb->transfer_buffer);
- usb_free_urb(ir->int_urb);
- return err;
- }
- ir->urb_data = kzalloc(size, GFP_KERNEL);
+
+ ir->submit_urb = 1;
+ schedule_delayed_work(&ir->work, msecs_to_jiffies(URB_SUBMIT_DELAY));
return 0;
}
-void tm6000_ir_int_stop(struct tm6000_core *dev)
+static void __tm6000_ir_int_stop(struct rc_dev *rc)
{
- struct tm6000_IR *ir = dev->ir;
+ struct tm6000_IR *ir = rc->priv;
- if (!ir)
+ if (!ir || !ir->int_urb)
return;
+ dprintk(2, "%s\n",__func__);
+
usb_kill_urb(ir->int_urb);
kfree(ir->int_urb->transfer_buffer);
usb_free_urb(ir->int_urb);
ir->int_urb = NULL;
- kfree(ir->urb_data);
- ir->urb_data = NULL;
+}
+
+int tm6000_ir_int_start(struct tm6000_core *dev)
+{
+ struct tm6000_IR *ir = dev->ir;
+
+ return __tm6000_ir_int_start(ir->rc);
+}
+
+void tm6000_ir_int_stop(struct tm6000_core *dev)
+{
+ struct tm6000_IR *ir = dev->ir;
+
+ __tm6000_ir_int_stop(ir->rc);
}
int tm6000_ir_init(struct tm6000_core *dev)
if (!dev->ir_codes)
return 0;
- ir = kzalloc(sizeof(*ir), GFP_KERNEL);
+ dprintk(2, "%s\n",__func__);
+
+ ir = kzalloc(sizeof(*ir), GFP_ATOMIC);
rc = rc_allocate_device();
if (!ir || !rc)
goto out;
dev->ir = ir;
ir->rc = rc;
- /* input einrichten */
+ /* input setup */
rc->allowed_protos = RC_TYPE_RC5 | RC_TYPE_NEC;
rc->priv = ir;
rc->change_protocol = tm6000_ir_change_protocol;
- rc->open = tm6000_ir_start;
- rc->close = tm6000_ir_stop;
+ if (&dev->int_in) {
+ rc->open = __tm6000_ir_int_start;
+ rc->close = __tm6000_ir_int_stop;
+ INIT_DELAYED_WORK(&ir->work, tm6000_ir_int_work);
+ } else {
+ rc->open = tm6000_ir_start;
+ rc->close = tm6000_ir_stop;
+ ir->polling = 50;
+ INIT_DELAYED_WORK(&ir->work, tm6000_ir_handle_key);
+ }
rc->driver_type = RC_DRIVER_SCANCODE;
- ir->polling = 50;
- ir->pwled = 0;
- ir->pwledcnt = 0;
-
-
snprintf(ir->name, sizeof(ir->name), "tm5600/60x0 IR (%s)",
dev->name);
rc->driver_name = "tm6000";
rc->dev.parent = &dev->udev->dev;
- if (&dev->int_in) {
- dprintk("IR over int\n");
-
- err = tm6000_ir_int_start(dev);
-
- if (err)
- goto out;
- }
-
/* ir register */
err = rc_register_device(rc);
if (err)
if (!ir)
return 0;
+ dprintk(2, "%s\n",__func__);
+
rc_unregister_device(ir->rc);
- if (ir->int_urb)
- tm6000_ir_int_stop(dev);
+ if (!ir->polling)
+ __tm6000_ir_int_stop(ir->rc);
+
+ tm6000_ir_stop(ir->rc);
+
+ /* Turn off the led */
+ tm6000_flash_led(dev, 0);
+ ir->pwled = 0;
+
kfree(ir);
dev->ir = NULL;
projects / platform / kernel / linux-3.10.git / commitdiff