GDB/testsuite: Avoid timeout lowering

The recent change to introduce `gdb_reverse_timeout' turned out
ineffective for board setups that set the `gdb,timeout' target variable.
A lower `gdb,timeout' setting takes precedence and defeats the effect of
`gdb_reverse_timeout'.  This is because the global timeout is overridden
in gdb_test_multiple and then again in gdb_expect.

Three timeout variables are taken into account in these two places, in
this precedence:

1. The `gdb,timeout' target variable.

2. The caller's local `timeout' variable (upvar timeout)

3. The global `timeout' variable.

This precedence is obeyed by gdb_test_multiple strictly.  OTOH
gdb_expect will select the higher of the two formers and will only take
the latter into account if none of the formers is present.  However the
two timeout selections are conceptually the same and gdb_test_multiple
does its only for the purpose of passing it down to gdb_expect.

Therefore I decided there is no point to keep carrying on this
duplication and removed the sequence from gdb_test_multiple, however
retaining the `upvar timeout' variable definition.  This way gdb_expect
will still access gdb_test_multiple's caller `timeout' variable (if any)
via its own `upvar timeout' reference.

Now as to the sequence in gdb_expect.  In addition to the three
variables described above it also takes a timeout argument into account,
as the fourth value to choose from.  It is currently used if it is
higher than the timeout selected from the variables as described above.

With the timeout selection code from gdb_test_multiple gone, gone is
also the most prominent use of this timeout argument, it's now used in
a couple of places only, mostly within this test framework library code
itself for preparatory commands or suchlike.  With this being the case
this timeout selection code can be simplified as follows:

1. Among the three timeout variables, the highest is always chosen.
   This is so that a test case doesn't inadvertently lower a high value
   timeout needed by slow target boards.  This is what all test cases
   use.

2. Any timeout argument takes precedence.  This is for special cases
   such as within the framework library code, e.g. it doesn't make sense
   to send `set height 0' with a timeout of 7200 seconds.  This is a
   local command that does not interact with the target and setting a
   high timeout here only risks a test suite run taking ages if it goes
   astray for some reason.

3. The fallback timeout of 60s remains.

	* lib/gdb.exp (gdb_test_multiple): Remove code to select the
	timeout, don't pass one down to gdb_expect.
	(gdb_expect): Rework timeout selection.

diff --git a/gdb/testsuite/ChangeLog b/gdb/testsuite/ChangeLog
index 0691c46..24fde49 100644 (file)
--- a/gdb/testsuite/ChangeLog
+++ b/gdb/testsuite/ChangeLog
@@ -1,5 +1,11 @@
 2014-09-09  Maciej W. Rozycki  <macro@codesourcery.com>
 
+       * lib/gdb.exp (gdb_test_multiple): Remove code to select the
+       timeout, don't pass one down to gdb_expect.
+       (gdb_expect): Rework timeout selection.
+
+2014-09-09  Maciej W. Rozycki  <macro@codesourcery.com>
+
        * lib/gdbserver-support.exp (gdbserver_start): Throw an error
        exception on timeout.
        (gdbserver_run): Catch any `gdbserver_spawn' error exceptions.

diff --git a/gdb/testsuite/lib/gdb.exp b/gdb/testsuite/lib/gdb.exp
index 1019ecd..82242f4 100644 (file)
--- a/gdb/testsuite/lib/gdb.exp
+++ b/gdb/testsuite/lib/gdb.exp
@@ -792,21 +792,6 @@ proc gdb_test_multiple { command message user_code } {
        }
     }
 
-    if [target_info exists gdb,timeout] {
-       set tmt [target_info gdb,timeout]
-    } else {
-       if [info exists timeout] {
-           set tmt $timeout
-       } else {
-           global timeout
-           if [info exists timeout] {
-               set tmt $timeout
-           } else {
-               set tmt 60
-           }
-       }
-    }
-
     set code {
        -re ".*A problem internal to GDB has been detected" {
            fail "$message (GDB internal error)"
@@ -912,7 +897,7 @@ proc gdb_test_multiple { command message user_code } {
     }
 
     set result 0
-    set code [catch {gdb_expect $tmt $code} string]
+    set code [catch {gdb_expect $code} string]
     if {$code == 1} {
        global errorInfo errorCode
        return -code error -errorinfo $errorInfo -errorcode $errorCode $string
@@ -3127,35 +3112,27 @@ proc gdb_expect { args } {
        set expcode $args
     }
 
+    # A timeout argument takes precedence, otherwise of all the timeouts
+    # select the largest.
+    upvar #0 timeout gtimeout
     upvar timeout timeout
-
-    if [target_info exists gdb,timeout] {
+    if [info exists atimeout] {
+       set tmt $atimeout
+    } else {
+       set tmt 0
        if [info exists timeout] {
-           if { $timeout < [target_info gdb,timeout] } {
-               set gtimeout [target_info gdb,timeout]
-           } else {
-               set gtimeout $timeout
-           }
-       } else {
-           set gtimeout [target_info gdb,timeout]
+           set tmt $timeout
        }
-    }
-
-    if ![info exists gtimeout] {
-       global timeout
-       if [info exists timeout] {
-           set gtimeout $timeout
+       if { [info exists gtimeout] && $gtimeout > $tmt } {
+           set tmt $gtimeout
        }
-    }
-
-    if [info exists atimeout] {
-       if { ![info exists gtimeout] || $gtimeout < $atimeout } {
-           set gtimeout $atimeout
+       if { [target_info exists gdb,timeout]
+            && [target_info gdb,timeout] > $tmt } {
+           set tmt [target_info gdb,timeout]
        }
-    } else {
-       if ![info exists gtimeout] {
+       if { $tmt == 0 } {
            # Eeeeew.
-           set gtimeout 60
+           set tmt 60
        }
     }
 
@@ -3170,7 +3147,7 @@ proc gdb_expect { args } {
        }
     }
     set code [catch \
-       {uplevel remote_expect host $gtimeout $expcode} string]
+       {uplevel remote_expect host $tmt $expcode} string]
     if [info exists old_val] {
        set remote_suppress_flag $old_val
     } else {