drm/vc4: Make DSI call into the bridge after the DSI link is enabled.

This allows panels or bridges that need to send DSI commands during
pre_enable() to successfully send them.  We delay DISP0 (aka the
actual display) enabling until after pre_enable so that pixels aren't
streaming before then.

v2: Just clear out the encoder->bridge value to disable the midlayer
    calls (idea by Andrzej Hajda).

Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621231759.29604-1-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>

diff --git a/drivers/gpu/drm/vc4/vc4_dsi.c b/drivers/gpu/drm/vc4/vc4_dsi.c
index 8aa8978..9c8e893 100644 (file)
--- a/drivers/gpu/drm/vc4/vc4_dsi.c
+++ b/drivers/gpu/drm/vc4/vc4_dsi.c
@@ -814,7 +814,9 @@ static void vc4_dsi_encoder_disable(struct drm_encoder *encoder)
        struct vc4_dsi *dsi = vc4_encoder->dsi;
        struct device *dev = &dsi->pdev->dev;
 
+       drm_bridge_disable(dsi->bridge);
        vc4_dsi_ulps(dsi, true);
+       drm_bridge_post_disable(dsi->bridge);
 
        clk_disable_unprepare(dsi->pll_phy_clock);
        clk_disable_unprepare(dsi->escape_clock);
@@ -1089,21 +1091,6 @@ static void vc4_dsi_encoder_enable(struct drm_encoder *encoder)
        /* Display reset sequence timeout */
        DSI_PORT_WRITE(PR_TO_CNT, 100000);
 
-       if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
-               DSI_PORT_WRITE(DISP0_CTRL,
-                              VC4_SET_FIELD(dsi->divider,
-                                            DSI_DISP0_PIX_CLK_DIV) |
-                              VC4_SET_FIELD(dsi->format, DSI_DISP0_PFORMAT) |
-                              VC4_SET_FIELD(DSI_DISP0_LP_STOP_PERFRAME,
-                                            DSI_DISP0_LP_STOP_CTRL) |
-                              DSI_DISP0_ST_END |
-                              DSI_DISP0_ENABLE);
-       } else {
-               DSI_PORT_WRITE(DISP0_CTRL,
-                              DSI_DISP0_COMMAND_MODE |
-                              DSI_DISP0_ENABLE);
-       }
-
        /* Set up DISP1 for transferring long command payloads through
         * the pixfifo.
         */
@@ -1128,6 +1115,25 @@ static void vc4_dsi_encoder_enable(struct drm_encoder *encoder)
 
        vc4_dsi_ulps(dsi, false);
 
+       drm_bridge_pre_enable(dsi->bridge);
+
+       if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
+               DSI_PORT_WRITE(DISP0_CTRL,
+                              VC4_SET_FIELD(dsi->divider,
+                                            DSI_DISP0_PIX_CLK_DIV) |
+                              VC4_SET_FIELD(dsi->format, DSI_DISP0_PFORMAT) |
+                              VC4_SET_FIELD(DSI_DISP0_LP_STOP_PERFRAME,
+                                            DSI_DISP0_LP_STOP_CTRL) |
+                              DSI_DISP0_ST_END |
+                              DSI_DISP0_ENABLE);
+       } else {
+               DSI_PORT_WRITE(DISP0_CTRL,
+                              DSI_DISP0_COMMAND_MODE |
+                              DSI_DISP0_ENABLE);
+       }
+
+       drm_bridge_enable(dsi->bridge);
+
        if (debug_dump_regs) {
                DRM_INFO("DSI regs after:\n");
                vc4_dsi_dump_regs(dsi);
@@ -1639,6 +1645,12 @@ static int vc4_dsi_bind(struct device *dev, struct device *master, void *data)
                dev_err(dev, "bridge attach failed: %d\n", ret);
                return ret;
        }
+       /* Disable the atomic helper calls into the bridge.  We
+        * manually call the bridge pre_enable / enable / etc. calls
+        * from our driver, since we need to sequence them within the
+        * encoder's enable/disable paths.
+        */
+       dsi->encoder->bridge = NULL;
 
        pm_runtime_enable(dev);