/*
- * Copyright (C) 2012 Altera Corporation <www.altera.com>
+ * Copyright (C) 2012 Altera Corporation <www.altera.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
-#ifndef __CONFIG_H
-#define __CONFIG_H
+#ifndef __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__
+#define __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__
#include <asm/arch/socfpga_base_addrs.h>
#include "../../board/altera/socfpga/pinmux_config.h"
#include "../../board/altera/socfpga/iocsr_config.h"
#include "../../board/altera/socfpga/pll_config.h"
-/*
- * High level configuration
- */
+#define CONFIG_SYS_GENERIC_BOARD
+
/* Virtual target or real hardware */
#undef CONFIG_SOCFPGA_VIRTUAL_TARGET
#define CONFIG_ARMV7
-#undef CONFIG_USE_IRQ
+#define CONFIG_SYS_THUMB_BUILD
-#define CONFIG_MISC_INIT_R
-#define CONFIG_SINGLE_BOOTLOADER
#define CONFIG_SOCFPGA
-#define CONFIG_CLOCKS
-#define CONFIG_SYS_ARM_CACHE_WRITEALLOC
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#define CONFIG_SYS_L2_PL310
-#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
+/* U-Boot Commands */
+#define CONFIG_SYS_NO_FLASH
+#include <config_cmd_default.h>
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FAT_WRITE
+#define CONFIG_HW_WATCHDOG
-/* base address for .text section */
-#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define CONFIG_SYS_TEXT_BASE 0x08000040
-#else
-#define CONFIG_SYS_TEXT_BASE 0x01000040
-#endif
-#define CONFIG_SYS_LOAD_ADDR 0x7fc0
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE 256
-/* Monitor Command Prompt */
-#define CONFIG_SYS_PROMPT "SOCFPGA_CYCLONE5 # "
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_REGEX /* Enable regular expression support */
/*
- * Display CPU and Board Info
+ * High level configuration
*/
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-
-/*
- * Enable early stage initialization at C environment
- */
#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MISC_INIT_R
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_CLOCKS
-/* flat device tree */
+#define CONFIG_FIT
#define CONFIG_OF_LIBFDT
-/* skip updating the FDT blob */
-#define CONFIG_FDT_BLOB_SKIP_UPDATE
-/* Initial Memory map size for Linux, minus 4k alignment for DFT blob */
-#define CONFIG_SYS_BOOTMAPSZ ((256*1024*1024) - (4*1024))
+#define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024)
-#define CONFIG_SPL_RAM_DEVICE
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
-#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start))
-#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start)
+#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/*
- * Memory allocation (MALLOC)
+ * Memory configurations
*/
-/* Room required on the stack for the environment data */
-#define CONFIG_ENV_SIZE 1024
-/* Size of DRAM reserved for malloc() use */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB on SoCDK */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 0x0
+#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
+#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
-/* SP location before relocation, must use scratch RAM */
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
-/* Reserving 0x100 space at back of scratch RAM for debug info */
#define CONFIG_SYS_INIT_RAM_SIZE (0x10000 - 0x100)
-/* Stack pointer prior relocation, must situated at on-chip RAM */
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_SYS_NO_FLASH
-#include <config_cmd_default.h>
-/* FAT file system support */
-#define CONFIG_CMD_FAT
-/* bootz command support */
-#define CONFIG_CMD_BOOTZ
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
-
-/*
- * Misc
- */
-#define CONFIG_DOS_PARTITION 1
-
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_PARTITIONS
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
+#define CONFIG_SYS_TEXT_BASE 0x08000040
+#else
+#define CONFIG_SYS_TEXT_BASE 0x01000040
#endif
-/*
- * Environment setup
- */
-
-/* Delay before automatically booting the default image */
-#define CONFIG_BOOTDELAY 3
-/* Enable auto completion of commands using TAB */
-#define CONFIG_AUTO_COMPLETE
-/* use "hush" command parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#define CONFIG_CMD_RUN
-
+/* Booting Linux */
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTFILE "zImage"
+#define CONFIG_BOOTARGS "console=ttyS0" __stringify(CONFIG_BAUDRATE)
#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define CONFIG_BOOTCOMMAND "run ramboot"
+#define CONFIG_BOOTCOMMAND "run ramboot"
#else
-#define CONFIG_BOOTCOMMAND "run mmcload; run mmcboot"
+#define CONFIG_BOOTCOMMAND "run mmcload; run mmcboot"
#endif
+#define CONFIG_LOADADDR 0x8000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/*
- * arguments passed to the bootm command. The value of
- * CONFIG_BOOTARGS goes into the environment value "bootargs".
- * Do note the value will overide also the chosen node in FDT blob.
+ * U-Boot general configurations
*/
-#define CONFIG_BOOTARGS "console=ttyS0," __stringify(CONFIG_BAUDRATE)
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "verify=n\0" \
- "loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
- "ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
- "bootm ${loadaddr} - ${fdt_addr}\0" \
- "bootimage=zImage\0" \
- "fdt_addr=100\0" \
- "fdtimage=socfpga.dtb\0" \
- "fsloadcmd=ext2load\0" \
- "bootm ${loadaddr} - ${fdt_addr}\0" \
- "mmcroot=/dev/mmcblk0p2\0" \
- "mmcboot=setenv bootargs " CONFIG_BOOTARGS \
- " root=${mmcroot} rw rootwait;" \
- "bootz ${loadaddr} - ${fdt_addr}\0" \
- "mmcload=mmc rescan;" \
- "fatload mmc 0:1 ${loadaddr} ${bootimage};" \
- "fatload mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
- "qspiroot=/dev/mtdblock0\0" \
- "qspirootfstype=jffs2\0" \
- "qspiboot=setenv bootargs " CONFIG_BOOTARGS \
- " root=${qspiroot} rw rootfstype=${qspirootfstype};"\
- "bootm ${loadaddr} - ${fdt_addr}\0"
-
-/* using environment setting for stdin, stdout, stderr */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-/* Enable the call to overwrite_console() */
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-/* Enable overwrite of previous console environment settings */
-#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
-
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS 16
-
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+ /* Print buffer size */
+#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+ /* Boot argument buffer size */
+#define CONFIG_VERSION_VARIABLE /* U-BOOT version */
+#define CONFIG_AUTO_COMPLETE /* Command auto complete */
+#define CONFIG_CMDLINE_EDITING /* Command history etc */
+#define CONFIG_SYS_HUSH_PARSER
/*
- * Hardware drivers
+ * Cache
*/
+#define CONFIG_SYS_ARM_CACHE_WRITEALLOC
+#define CONFIG_SYS_CACHELINE_SIZE 32
+#define CONFIG_SYS_L2_PL310
+#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
/*
- * SDRAM Memory Map
+ * Ethernet on SoC (EMAC)
*/
-/* We have 1 bank of DRAM */
-#define CONFIG_NR_DRAM_BANKS 1
-/* SDRAM Bank #1 */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-/* SDRAM memory size */
-#define PHYS_SDRAM_1_SIZE 0x40000000
+#if defined(CONFIG_CMD_NET) && !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET)
+#define CONFIG_DESIGNWARE_ETH
+#define CONFIG_NET_MULTI
+#define CONFIG_DW_ALTDESCRIPTOR
+#define CONFIG_MII
+#define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ)
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_GIGE
-#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_START 0x00000000
-#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
+#define CONFIG_EMAC_BASE SOCFPGA_EMAC0_ADDRESS
+#define CONFIG_PHY_INTERFACE_MODE PHY_INTERFACE_MODE_RGMII
+#define CONFIG_EPHY0_PHY_ADDR 0
+
+/* PHY */
+#define CONFIG_EPHY1_PHY_ADDR 4
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9021
+#define CONFIG_KSZ9021_CLK_SKEW_ENV "micrel-ksz9021-clk-skew"
+#define CONFIG_KSZ9021_CLK_SKEW_VAL 0xf0f0
+#define CONFIG_KSZ9021_DATA_SKEW_ENV "micrel-ksz9021-data-skew"
+#define CONFIG_KSZ9021_DATA_SKEW_VAL 0x0
-/*
- * NS16550 Configuration
- */
-#define UART0_BASE SOCFPGA_UART0_ADDRESS
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550_COM1 UART0_BASE
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200}
-#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define V_NS16550_CLK 1000000
-#else
-#define V_NS16550_CLK 100000000
#endif
-#define CONFIG_BAUDRATE 115200
/*
- * FLASH
+ * FPGA Driver
*/
-#define CONFIG_SYS_NO_FLASH
+#ifdef CONFIG_CMD_FPGA
+#define CONFIG_FPGA
+#define CONFIG_FPGA_ALTERA
+#define CONFIG_FPGA_SOCFPGA
+#define CONFIG_FPGA_COUNT 1
+#endif
/*
* L4 OSC1 Timer 0
*/
-/* This timer use eosc1 where the clock frequency is fixed
- * throughout any condition */
+/* This timer uses eosc1, whose clock frequency is fixed at any condition. */
#define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS
-/* Timer info */
+#define CONFIG_SYS_TIMER_COUNTS_DOWN
+#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
#define CONFIG_SYS_TIMER_RATE 2400000
#else
#define CONFIG_SYS_TIMER_RATE 25000000
#endif
-#define CONFIG_SYS_TIMER_COUNTS_DOWN
-#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
-
-#define CONFIG_ENV_IS_NOWHERE
-
-/*
- * network support
- */
-#ifndef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define CONFIG_DESIGNWARE_ETH 1
-#endif
-
-#ifdef CONFIG_DESIGNWARE_ETH
-#define CONFIG_EMAC0_BASE SOCFPGA_EMAC0_ADDRESS
-#define CONFIG_EMAC1_BASE SOCFPGA_EMAC1_ADDRESS
-/* console support for network */
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-/* designware */
-#define CONFIG_NET_MULTI
-#define CONFIG_DW_ALTDESCRIPTOR
-#define CONFIG_MII
-#define CONFIG_PHY_GIGE
-#define CONFIG_DW_AUTONEG
-#define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ)
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_MICREL
-#define CONFIG_PHY_MICREL_KSZ9021
-/* EMAC controller and PHY used */
-#define CONFIG_EMAC_BASE CONFIG_EMAC1_BASE
-#define CONFIG_EPHY_PHY_ADDR CONFIG_EPHY1_PHY_ADDR
-#define CONFIG_PHY_INTERFACE_MODE PHY_INTERFACE_MODE_RGMII
-#endif /* CONFIG_DESIGNWARE_ETH */
/*
* L4 Watchdog
*/
-#define CONFIG_HW_WATCHDOG
-#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 2000
+#ifdef CONFIG_HW_WATCHDOG
#define CONFIG_DESIGNWARE_WATCHDOG
#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
-/* Clocks source frequency to watchdog timer */
#define CONFIG_DW_WDT_CLOCK_KHZ 25000
+#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 12000
+#endif
/*
- * MMC support
+ * MMC Driver
*/
+#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
-#ifdef CONFIG_MMC
#define CONFIG_BOUNCE_BUFFER
-#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_DWMMC
#define CONFIG_SOCFPGA_DWMMC
#define CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH 1024
#define CONFIG_SOCFPGA_DWMMC_DRVSEL 3
#define CONFIG_SOCFPGA_DWMMC_SMPSEL 0
+/* FIXME */
/* using smaller max blk cnt to avoid flooding the limited stack we have */
-#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256
-#endif /* CONFIG_MMC */
+#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256 /* FIXME -- SPL only? */
+#endif
/*
- * SPL "Second Program Loader" aka Initial Software
+ * Serial Driver
*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE -4
+#define CONFIG_SYS_NS16550_COM1 SOCFPGA_UART0_ADDRESS
+#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
+#define CONFIG_SYS_NS16550_CLK 1000000
+#else
+#define CONFIG_SYS_NS16550_CLK 100000000
+#endif
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
-/* Enable building of SPL globally */
-#define CONFIG_SPL_FRAMEWORK
-
-/* TEXT_BASE for linking the SPL binary */
-#define CONFIG_SPL_TEXT_BASE 0xFFFF0000
+/*
+ * USB
+ * Ungate USB:
+ * mw 0xffd05014 0x01bef032
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_DWC2_OTG
+/*#define CONFIG_USB_DWC2_REG_ADDR 0xffb00000*/
+#define CONFIG_USB_DWC2_REG_ADDR 0xffb40000
+#define CONFIG_USB_STORAGE
+#endif
-/* Stack size for SPL */
-#define CONFIG_SPL_STACK_SIZE (4 * 1024)
+/*
+ * U-Boot environment
+ */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE 4096
+#define CONFIG_HOSTNAME socfpga_cyclone5
-/* MALLOC size for SPL */
-#define CONFIG_SPL_MALLOC_SIZE (5 * 1024)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "verify=n\0" \
+ "loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+ "ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
+ "bootm ${loadaddr} - ${fdt_addr}\0" \
+ "bootimage=zImage\0" \
+ "fdt_addr=100\0" \
+ "fdtimage=socfpga.dtb\0" \
+ "fsloadcmd=ext2load\0" \
+ "bootm ${loadaddr} - ${fdt_addr}\0" \
+ "mmcroot=/dev/mmcblk0p2\0" \
+ "mmcboot=setenv bootargs " CONFIG_BOOTARGS \
+ " root=${mmcroot} rw rootwait;" \
+ "bootz ${loadaddr} - ${fdt_addr}\0" \
+ "mmcload=mmc rescan;" \
+ "fatload mmc 0:1 ${loadaddr} ${bootimage};" \
+ "fatload mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
+ "qspiroot=/dev/mtdblock0\0" \
+ "qspirootfstype=jffs2\0" \
+ "qspiboot=setenv bootargs " CONFIG_BOOTARGS \
+ " root=${qspiroot} rw rootfstype=${qspirootfstype};"\
+ "bootm ${loadaddr} - ${fdt_addr}\0"
-#define CONFIG_SPL_SERIAL_SUPPORT
+/*
+ * SPL
+ */
+#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_RAM_DEVICE
+#define CONFIG_SPL_TEXT_BASE 0xFFFF0000
+#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
+#define CONFIG_SPL_STACK_SIZE (4 * 1024)
+#define CONFIG_SPL_MALLOC_SIZE (5 * 1024) /* FIXME */
+#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start))
+#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start)
-#define CHUNKSZ_CRC32 (1 * 1024)
-
+#define CHUNKSZ_CRC32 (1 * 1024) /* FIXME: ewww */
#define CONFIG_CRC32_VERIFY
/* Linker script for SPL */
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds"
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds"
-/* Support for common/libcommon.o in SPL binary */
#define CONFIG_SPL_LIBCOMMON_SUPPORT
-/* Support for lib/libgeneric.o in SPL binary */
#define CONFIG_SPL_LIBGENERIC_SUPPORT
-
-/* Support for watchdog */
#define CONFIG_SPL_WATCHDOG_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#ifdef CONFIG_SPL_BUILD
+#undef CONFIG_PARTITIONS
+#endif
-#endif /* __CONFIG_H */
+#endif /* __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__ */
projects / platform / kernel / u-boot.git / commitdiff