*/
/*
-Driver: amplc_dio200
-Description: Amplicon 200 Series Digital I/O
-Author: Ian Abbott <abbotti@mev.co.uk>
-Devices: [Amplicon] PC212E (pc212e), PC214E (pc214e), PC215E (pc215e),
- PCI215 (pci215 or amplc_dio200), PC218E (pc218e), PC272E (pc272e),
- PCI272 (pci272 or amplc_dio200)
-Updated: Wed, 22 Oct 2008 13:36:02 +0100
-Status: works
-
-Configuration options - PC212E, PC214E, PC215E, PC218E, PC272E:
- [0] - I/O port base address
- [1] - IRQ (optional, but commands won't work without it)
-
-Configuration options - PCI215, PCI272:
- [0] - PCI bus of device (optional)
- [1] - PCI slot of device (optional)
- If bus/slot is not specified, the first available PCI device will
- be used.
-
-Passing a zero for an option is the same as leaving it unspecified.
-
-SUBDEVICES
-
- PC218E PC212E PC215E/PCI215
- ------------- ------------- -------------
- Subdevices 7 6 5
- 0 CTR-X1 PPI-X PPI-X
- 1 CTR-X2 CTR-Y1 PPI-Y
- 2 CTR-Y1 CTR-Y2 CTR-Z1
- 3 CTR-Y2 CTR-Z1 CTR-Z2
- 4 CTR-Z1 CTR-Z2 INTERRUPT
- 5 CTR-Z2 INTERRUPT
- 6 INTERRUPT
-
- PC214E PC272E/PCI272
- ------------- -------------
- Subdevices 4 4
- 0 PPI-X PPI-X
- 1 PPI-Y PPI-Y
- 2 CTR-Z1* PPI-Z
- 3 INTERRUPT* INTERRUPT
-
-Each PPI is a 8255 chip providing 24 DIO channels. The DIO channels
-are configurable as inputs or outputs in four groups:
-
- Port A - channels 0 to 7
- Port B - channels 8 to 15
- Port CL - channels 16 to 19
- Port CH - channels 20 to 23
-
-Only mode 0 of the 8255 chips is supported.
-
-Each CTR is a 8254 chip providing 3 16-bit counter channels. Each
-channel is configured individually with INSN_CONFIG instructions. The
-specific type of configuration instruction is specified in data[0].
-Some configuration instructions expect an additional parameter in
-data[1]; others return a value in data[1]. The following configuration
-instructions are supported:
-
- INSN_CONFIG_SET_COUNTER_MODE. Sets the counter channel's mode and
- BCD/binary setting specified in data[1].
-
- INSN_CONFIG_8254_READ_STATUS. Reads the status register value for the
- counter channel into data[1].
-
- INSN_CONFIG_SET_CLOCK_SRC. Sets the counter channel's clock source as
- specified in data[1] (this is a hardware-specific value). Not
- supported on PC214E. For the other boards, valid clock sources are
- 0 to 7 as follows:
-
- 0. CLK n, the counter channel's dedicated CLK input from the SK1
- connector. (N.B. for other values, the counter channel's CLKn
- pin on the SK1 connector is an output!)
- 1. Internal 10 MHz clock.
- 2. Internal 1 MHz clock.
- 3. Internal 100 kHz clock.
- 4. Internal 10 kHz clock.
- 5. Internal 1 kHz clock.
- 6. OUT n-1, the output of counter channel n-1 (see note 1 below).
- 7. Ext Clock, the counter chip's dedicated Ext Clock input from
- the SK1 connector. This pin is shared by all three counter
- channels on the chip.
-
- INSN_CONFIG_GET_CLOCK_SRC. Returns the counter channel's current
- clock source in data[1]. For internal clock sources, data[2] is set
- to the period in ns.
-
- INSN_CONFIG_SET_GATE_SRC. Sets the counter channel's gate source as
- specified in data[2] (this is a hardware-specific value). Not
- supported on PC214E. For the other boards, valid gate sources are 0
- to 7 as follows:
-
- 0. VCC (internal +5V d.c.), i.e. gate permanently enabled.
- 1. GND (internal 0V d.c.), i.e. gate permanently disabled.
- 2. GAT n, the counter channel's dedicated GAT input from the SK1
- connector. (N.B. for other values, the counter channel's GATn
- pin on the SK1 connector is an output!)
- 3. /OUT n-2, the inverted output of counter channel n-2 (see note
- 2 below).
- 4. Reserved.
- 5. Reserved.
- 6. Reserved.
- 7. Reserved.
-
- INSN_CONFIG_GET_GATE_SRC. Returns the counter channel's current gate
- source in data[2].
-
-Clock and gate interconnection notes:
-
- 1. Clock source OUT n-1 is the output of the preceding channel on the
- same counter subdevice if n > 0, or the output of channel 2 on the
- preceding counter subdevice (see note 3) if n = 0.
-
- 2. Gate source /OUT n-2 is the inverted output of channel 0 on the
- same counter subdevice if n = 2, or the inverted output of channel n+1
- on the preceding counter subdevice (see note 3) if n < 2.
-
- 3. The counter subdevices are connected in a ring, so the highest
- counter subdevice precedes the lowest.
-
-The 'INTERRUPT' subdevice pretends to be a digital input subdevice. The
-digital inputs come from the interrupt status register. The number of
-channels matches the number of interrupt sources. The PC214E does not
-have an interrupt status register; see notes on 'INTERRUPT SOURCES'
-below.
-
-INTERRUPT SOURCES
-
- PC218E PC212E PC215E/PCI215
- ------------- ------------- -------------
- Sources 6 6 6
- 0 CTR-X1-OUT PPI-X-C0 PPI-X-C0
- 1 CTR-X2-OUT PPI-X-C3 PPI-X-C3
- 2 CTR-Y1-OUT CTR-Y1-OUT PPI-Y-C0
- 3 CTR-Y2-OUT CTR-Y2-OUT PPI-Y-C3
- 4 CTR-Z1-OUT CTR-Z1-OUT CTR-Z1-OUT
- 5 CTR-Z2-OUT CTR-Z2-OUT CTR-Z2-OUT
-
- PC214E PC272E/PCI272
- ------------- -------------
- Sources 1 6
- 0 JUMPER-J5 PPI-X-C0
- 1 PPI-X-C3
- 2 PPI-Y-C0
- 3 PPI-Y-C3
- 4 PPI-Z-C0
- 5 PPI-Z-C3
-
-When an interrupt source is enabled in the interrupt source enable
-register, a rising edge on the source signal latches the corresponding
-bit to 1 in the interrupt status register.
-
-When the interrupt status register value as a whole (actually, just the
-6 least significant bits) goes from zero to non-zero, the board will
-generate an interrupt. For level-triggered hardware interrupts (PCI
-card), the interrupt will remain asserted until the interrupt status
-register is cleared to zero. For edge-triggered hardware interrupts
-(ISA card), no further interrupts will occur until the interrupt status
-register is cleared to zero. To clear a bit to zero in the interrupt
-status register, the corresponding interrupt source must be disabled
-in the interrupt source enable register (there is no separate interrupt
-clear register).
-
-The PC214E does not have an interrupt source enable register or an
-interrupt status register; its 'INTERRUPT' subdevice has a single
-channel and its interrupt source is selected by the position of jumper
-J5.
-
-COMMANDS
-
-The driver supports a read streaming acquisition command on the
-'INTERRUPT' subdevice. The channel list selects the interrupt sources
-to be enabled. All channels will be sampled together (convert_src ==
-TRIG_NOW). The scan begins a short time after the hardware interrupt
-occurs, subject to interrupt latencies (scan_begin_src == TRIG_EXT,
-scan_begin_arg == 0). The value read from the interrupt status register
-is packed into a short value, one bit per requested channel, in the
-order they appear in the channel list.
-*/
+ * Driver: amplc_dio200
+ * Description: Amplicon 200 Series Digital I/O
+
* Author: Ian Abbott <abbotti@mev.co.uk>
+ * Devices: [Amplicon] PC212E (pc212e), PC214E (pc214e), PC215E (pc215e),
+ * PCI215 (pci215 or amplc_dio200), PC218E (pc218e), PC272E (pc272e),
+ * PCI272 (pci272 or amplc_dio200)
+ * Updated: Wed, 22 Oct 2008 13:36:02 +0100
+ * Status: works
+ *
+ * Configuration options - PC212E, PC214E, PC215E, PC218E, PC272E:
+ * [0] - I/O port base address
+ * [1] - IRQ (optional, but commands won't work without it)
+ *
+ * Configuration options - PCI215, PCI272:
+ * [0] - PCI bus of device (optional)
+ * [1] - PCI slot of device (optional)
+ * If bus/slot is not specified, the first available PCI device will
+ * be used.
+ *
+ * Passing a zero for an option is the same as leaving it unspecified.
+ *
+ * SUBDEVICES
+ *
+ * PC218E PC212E PC215E/PCI215
+ * ------------- ------------- -------------
+ * Subdevices 7 6 5
+ * 0 CTR-X1 PPI-X PPI-X
+ * 1 CTR-X2 CTR-Y1 PPI-Y
+ * 2 CTR-Y1 CTR-Y2 CTR-Z1
+ * 3 CTR-Y2 CTR-Z1 CTR-Z2
+ * 4 CTR-Z1 CTR-Z2 INTERRUPT
+ * 5 CTR-Z2 INTERRUPT
+ * 6 INTERRUPT
+ *
+ * PC214E PC272E/PCI272
+ * ------------- -------------
+ * Subdevices 4 4
+ * 0 PPI-X PPI-X
+ * 1 PPI-Y PPI-Y
+ * 2 CTR-Z1* PPI-Z
+ * 3 INTERRUPT* INTERRUPT
+ *
+ * Each PPI is a 8255 chip providing 24 DIO channels. The DIO channels
+ * are configurable as inputs or outputs in four groups:
+ *
+ * Port A - channels 0 to 7
+ * Port B - channels 8 to 15
+ * Port CL - channels 16 to 19
+ * Port CH - channels 20 to 23
+ *
+ * Only mode 0 of the 8255 chips is supported.
+ *
+ * Each CTR is a 8254 chip providing 3 16-bit counter channels. Each
+ * channel is configured individually with INSN_CONFIG instructions. The
+ * specific type of configuration instruction is specified in data[0].
+ * Some configuration instructions expect an additional parameter in
+ * data[1]; others return a value in data[1]. The following configuration
+ * instructions are supported:
+ *
+ * INSN_CONFIG_SET_COUNTER_MODE. Sets the counter channel's mode and
+ * BCD/binary setting specified in data[1].
+ *
+ * INSN_CONFIG_8254_READ_STATUS. Reads the status register value for the
+ * counter channel into data[1].
+ *
+ * INSN_CONFIG_SET_CLOCK_SRC. Sets the counter channel's clock source as
+ * specified in data[1] (this is a hardware-specific value). Not
+ * supported on PC214E. For the other boards, valid clock sources are
+ * 0 to 7 as follows:
+ *
+ * 0. CLK n, the counter channel's dedicated CLK input from the SK1
+ * connector. (N.B. for other values, the counter channel's CLKn
+ * pin on the SK1 connector is an output!)
+ * 1. Internal 10 MHz clock.
+ * 2. Internal 1 MHz clock.
+ * 3. Internal 100 kHz clock.
+ * 4. Internal 10 kHz clock.
+ * 5. Internal 1 kHz clock.
+ * 6. OUT n-1, the output of counter channel n-1 (see note 1 below).
+ * 7. Ext Clock, the counter chip's dedicated Ext Clock input from
+ * the SK1 connector. This pin is shared by all three counter
+ * channels on the chip.
+ *
+ * INSN_CONFIG_GET_CLOCK_SRC. Returns the counter channel's current
+ * clock source in data[1]. For internal clock sources, data[2] is set
+ * to the period in ns.
+ *
+ * INSN_CONFIG_SET_GATE_SRC. Sets the counter channel's gate source as
+ * specified in data[2] (this is a hardware-specific value). Not
+ * supported on PC214E. For the other boards, valid gate sources are 0
+ * to 7 as follows:
+ *
+ * 0. VCC (internal +5V d.c.), i.e. gate permanently enabled.
+ * 1. GND (internal 0V d.c.), i.e. gate permanently disabled.
+ * 2. GAT n, the counter channel's dedicated GAT input from the SK1
+ * connector. (N.B. for other values, the counter channel's GATn
+ * pin on the SK1 connector is an output!)
+ * 3. /OUT n-2, the inverted output of counter channel n-2 (see note
+ * 2 below).
+ * 4. Reserved.
+ * 5. Reserved.
+ * 6. Reserved.
+ * 7. Reserved.
+ *
+ * INSN_CONFIG_GET_GATE_SRC. Returns the counter channel's current gate
+ * source in data[2].
+ *
+ * Clock and gate interconnection notes:
+ *
+ * 1. Clock source OUT n-1 is the output of the preceding channel on the
+ * same counter subdevice if n > 0, or the output of channel 2 on the
+ * preceding counter subdevice (see note 3) if n = 0.
+ *
+ * 2. Gate source /OUT n-2 is the inverted output of channel 0 on the
+ * same counter subdevice if n = 2, or the inverted output of channel n+1
+ * on the preceding counter subdevice (see note 3) if n < 2.
+ *
+ * 3. The counter subdevices are connected in a ring, so the highest
+ * counter subdevice precedes the lowest.
+ *
+ * The 'INTERRUPT' subdevice pretends to be a digital input subdevice. The
+ * digital inputs come from the interrupt status register. The number of
+ * channels matches the number of interrupt sources. The PC214E does not
+ * have an interrupt status register; see notes on 'INTERRUPT SOURCES'
+ * below.
+ *
+ * INTERRUPT SOURCES
+ *
+ * PC218E PC212E PC215E/PCI215
+ * ------------- ------------- -------------
+ * Sources 6 6 6
+ * 0 CTR-X1-OUT PPI-X-C0 PPI-X-C0
+ * 1 CTR-X2-OUT PPI-X-C3 PPI-X-C3
+ * 2 CTR-Y1-OUT CTR-Y1-OUT PPI-Y-C0
+ * 3 CTR-Y2-OUT CTR-Y2-OUT PPI-Y-C3
+ * 4 CTR-Z1-OUT CTR-Z1-OUT CTR-Z1-OUT
+ * 5 CTR-Z2-OUT CTR-Z2-OUT CTR-Z2-OUT
+ *
+ * PC214E PC272E/PCI272
+ * ------------- -------------
+ * Sources 1 6
+ * 0 JUMPER-J5 PPI-X-C0
+ * 1 PPI-X-C3
+ * 2 PPI-Y-C0
+ * 3 PPI-Y-C3
+ * 4 PPI-Z-C0
+ * 5 PPI-Z-C3
+ *
+ * When an interrupt source is enabled in the interrupt source enable
+ * register, a rising edge on the source signal latches the corresponding
+ * bit to 1 in the interrupt status register.
+ *
+ * When the interrupt status register value as a whole (actually, just the
+ * 6 least significant bits) goes from zero to non-zero, the board will
+ * generate an interrupt. For level-triggered hardware interrupts (PCI
+ * card), the interrupt will remain asserted until the interrupt status
+ * register is cleared to zero. For edge-triggered hardware interrupts
+ * (ISA card), no further interrupts will occur until the interrupt status
+ * register is cleared to zero. To clear a bit to zero in the interrupt
+ * status register, the corresponding interrupt source must be disabled
+ * in the interrupt source enable register (there is no separate interrupt
+ * clear register).
+ *
+ * The PC214E does not have an interrupt source enable register or an
+ * interrupt status register; its 'INTERRUPT' subdevice has a single
+ * channel and its interrupt source is selected by the position of jumper
+ * J5.
+ *
+ * COMMANDS
+ *
+ * The driver supports a read streaming acquisition command on the
+ * 'INTERRUPT' subdevice. The channel list selects the interrupt sources
+ * to be enabled. All channels will be sampled together (convert_src ==
+ * TRIG_NOW). The scan begins a short time after the hardware interrupt
+ * occurs, subject to interrupt latencies (scan_begin_src == TRIG_EXT,
+ * scan_begin_arg == 0). The value read from the interrupt status register
+ * is packed into a short value, one bit per requested channel, in the
+ * order they appear in the channel list.
+ */
#include <linux/interrupt.h>
#include <linux/slab.h>
projects / profile / ivi / kernel-adaptation-intel-automotive.git / commitdiff