/* BIST fast-clear mode select. A BIST run with this bit set
* clears all entries in USBH RAMs to 0x0.
*/
-# define USBDRD_UCTL_CTL_CLEAR_BIST BIT(63)
+# define USBDRD_UCTL_CTL_CLEAR_BIST BIT_ULL(63)
/* 1 = Start BIST and cleared by hardware */
-# define USBDRD_UCTL_CTL_START_BIST BIT(62)
+# define USBDRD_UCTL_CTL_START_BIST BIT_ULL(62)
/* Reference clock select for SuperSpeed and HighSpeed PLLs:
* 0x0 = Both PLLs use DLMC_REF_CLK0 for reference clock
* 0x1 = Both PLLs use DLMC_REF_CLK1 for reference clock
* 0x3 = SuperSpeed PLL uses DLMC_REF_CLK1 for reference clock &
* HighSpeed PLL uses PLL_REF_CLK for reference clck
*/
-# define USBDRD_UCTL_CTL_REF_CLK_SEL GENMASK(61, 60)
+# define USBDRD_UCTL_CTL_REF_CLK_SEL GENMASK_ULL(61, 60)
/* 1 = Spread-spectrum clock enable, 0 = SS clock disable */
-# define USBDRD_UCTL_CTL_SSC_EN BIT(59)
+# define USBDRD_UCTL_CTL_SSC_EN BIT_ULL(59)
/* Spread-spectrum clock modulation range:
* 0x0 = -4980 ppm downspread
* 0x1 = -4492 ppm downspread
* 0x2 = -4003 ppm downspread
* 0x3 - 0x7 = Reserved
*/
-# define USBDRD_UCTL_CTL_SSC_RANGE GENMASK(58, 56)
+# define USBDRD_UCTL_CTL_SSC_RANGE GENMASK_ULL(58, 56)
/* Enable non-standard oscillator frequencies:
* [55:53] = modules -1
* [52:47] = 2's complement push amount, 0 = Feature disabled
*/
-# define USBDRD_UCTL_CTL_SSC_REF_CLK_SEL GENMASK(55, 47)
+# define USBDRD_UCTL_CTL_SSC_REF_CLK_SEL GENMASK_ULL(55, 47)
/* Reference clock multiplier for non-standard frequencies:
* 0x19 = 100MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
* 0x28 = 125MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
* 0x32 = 50MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
* Other Values = Reserved
*/
-# define USBDRD_UCTL_CTL_MPLL_MULTIPLIER GENMASK(46, 40)
+# define USBDRD_UCTL_CTL_MPLL_MULTIPLIER GENMASK_ULL(46, 40)
/* Enable reference clock to prescaler for SuperSpeed functionality.
* Should always be set to "1"
*/
-# define USBDRD_UCTL_CTL_REF_SSP_EN BIT(39)
+# define USBDRD_UCTL_CTL_REF_SSP_EN BIT_ULL(39)
/* Divide the reference clock by 2 before entering the
* REF_CLK_FSEL divider:
* If REF_CLK_SEL = 0x0 or 0x1, then only 0x0 is legal
* 0x1 = DLMC_REF_CLK* is 125MHz
* 0x0 = DLMC_REF_CLK* is another supported frequency
*/
-# define USBDRD_UCTL_CTL_REF_CLK_DIV2 BIT(38)
+# define USBDRD_UCTL_CTL_REF_CLK_DIV2 BIT_ULL(38)
/* Select reference clock freqnuency for both PLL blocks:
* 0x27 = REF_CLK_SEL is 0x0 or 0x1
* 0x07 = REF_CLK_SEL is 0x2 or 0x3
*/
-# define USBDRD_UCTL_CTL_REF_CLK_FSEL GENMASK(37, 32)
+# define USBDRD_UCTL_CTL_REF_CLK_FSEL GENMASK_ULL(37, 32)
/* Controller clock enable. */
-# define USBDRD_UCTL_CTL_H_CLK_EN BIT(30)
+# define USBDRD_UCTL_CTL_H_CLK_EN BIT_ULL(30)
/* Select bypass input to controller clock divider:
* 0x0 = Use divided coprocessor clock from H_CLKDIV
* 0x1 = Use clock from GPIO pins
*/
-# define USBDRD_UCTL_CTL_H_CLK_BYP_SEL BIT(29)
+# define USBDRD_UCTL_CTL_H_CLK_BYP_SEL BIT_ULL(29)
/* Reset controller clock divider. */
-# define USBDRD_UCTL_CTL_H_CLKDIV_RST BIT(28)
+# define USBDRD_UCTL_CTL_H_CLKDIV_RST BIT_ULL(28)
/* Clock divider select:
* 0x0 = divide by 1
* 0x1 = divide by 2
* 0x6 = divide by 24
* 0x7 = divide by 32
*/
-# define USBDRD_UCTL_CTL_H_CLKDIV_SEL GENMASK(26, 24)
+# define USBDRD_UCTL_CTL_H_CLKDIV_SEL GENMASK_ULL(26, 24)
/* USB3 port permanently attached: 0x0 = No, 0x1 = Yes */
-# define USBDRD_UCTL_CTL_USB3_PORT_PERM_ATTACH BIT(21)
+# define USBDRD_UCTL_CTL_USB3_PORT_PERM_ATTACH BIT_ULL(21)
/* USB2 port permanently attached: 0x0 = No, 0x1 = Yes */
-# define USBDRD_UCTL_CTL_USB2_PORT_PERM_ATTACH BIT(20)
+# define USBDRD_UCTL_CTL_USB2_PORT_PERM_ATTACH BIT_ULL(20)
/* Disable SuperSpeed PHY: 0x0 = No, 0x1 = Yes */
-# define USBDRD_UCTL_CTL_USB3_PORT_DISABLE BIT(18)
+# define USBDRD_UCTL_CTL_USB3_PORT_DISABLE BIT_ULL(18)
/* Disable HighSpeed PHY: 0x0 = No, 0x1 = Yes */
-# define USBDRD_UCTL_CTL_USB2_PORT_DISABLE BIT(16)
+# define USBDRD_UCTL_CTL_USB2_PORT_DISABLE BIT_ULL(16)
/* Enable PHY SuperSpeed block power: 0x0 = No, 0x1 = Yes */
-# define USBDRD_UCTL_CTL_SS_POWER_EN BIT(14)
+# define USBDRD_UCTL_CTL_SS_POWER_EN BIT_ULL(14)
/* Enable PHY HighSpeed block power: 0x0 = No, 0x1 = Yes */
-# define USBDRD_UCTL_CTL_HS_POWER_EN BIT(12)
+# define USBDRD_UCTL_CTL_HS_POWER_EN BIT_ULL(12)
/* Enable USB UCTL interface clock: 0xx = No, 0x1 = Yes */
-# define USBDRD_UCTL_CTL_CSCLK_EN BIT(4)
+# define USBDRD_UCTL_CTL_CSCLK_EN BIT_ULL(4)
/* Controller mode: 0x0 = Host, 0x1 = Device */
-# define USBDRD_UCTL_CTL_DRD_MODE BIT(3)
+# define USBDRD_UCTL_CTL_DRD_MODE BIT_ULL(3)
/* PHY reset */
-# define USBDRD_UCTL_CTL_UPHY_RST BIT(2)
+# define USBDRD_UCTL_CTL_UPHY_RST BIT_ULL(2)
/* Software reset UAHC */
-# define USBDRD_UCTL_CTL_UAHC_RST BIT(1)
+# define USBDRD_UCTL_CTL_UAHC_RST BIT_ULL(1)
/* Software resets UCTL */
-# define USBDRD_UCTL_CTL_UCTL_RST BIT(0)
+# define USBDRD_UCTL_CTL_UCTL_RST BIT_ULL(0)
#define USBDRD_UCTL_BIST_STATUS 0x08
#define USBDRD_UCTL_SPARE0 0x10
*/
#define USBDRD_UCTL_HOST_CFG 0xe0
/* Indicates minimum value of all received BELT values */
-# define USBDRD_UCTL_HOST_CFG_HOST_CURRENT_BELT GENMASK(59, 48)
+# define USBDRD_UCTL_HOST_CFG_HOST_CURRENT_BELT GENMASK_ULL(59, 48)
/* HS jitter adjustment */
-# define USBDRD_UCTL_HOST_CFG_FLA GENMASK(37, 32)
+# define USBDRD_UCTL_HOST_CFG_FLA GENMASK_ULL(37, 32)
/* Bus-master enable: 0x0 = Disabled (stall DMAs), 0x1 = enabled */
-# define USBDRD_UCTL_HOST_CFG_BME BIT(28)
+# define USBDRD_UCTL_HOST_CFG_BME BIT_ULL(28)
/* Overcurrent protection enable: 0x0 = unavailable, 0x1 = available */
-# define USBDRD_UCTL_HOST_OCI_EN BIT(27)
+# define USBDRD_UCTL_HOST_OCI_EN BIT_ULL(27)
/* Overcurrent sene selection:
* 0x0 = Overcurrent indication from off-chip is active-low
* 0x1 = Overcurrent indication from off-chip is active-high
*/
-# define USBDRD_UCTL_HOST_OCI_ACTIVE_HIGH_EN BIT(26)
+# define USBDRD_UCTL_HOST_OCI_ACTIVE_HIGH_EN BIT_ULL(26)
/* Port power control enable: 0x0 = unavailable, 0x1 = available */
-# define USBDRD_UCTL_HOST_PPC_EN BIT(25)
+# define USBDRD_UCTL_HOST_PPC_EN BIT_ULL(25)
/* Port power control sense selection:
* 0x0 = Port power to off-chip is active-low
* 0x1 = Port power to off-chip is active-high
*/
-# define USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN BIT(24)
+# define USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN BIT_ULL(24)
/*
* UCTL Shim Features Register
*/
#define USBDRD_UCTL_SHIM_CFG 0xe8
/* Out-of-bound UAHC register access: 0 = read, 1 = write */
-# define USBDRD_UCTL_SHIM_CFG_XS_NCB_OOB_WRN BIT(63)
+# define USBDRD_UCTL_SHIM_CFG_XS_NCB_OOB_WRN BIT_ULL(63)
/* SRCID error log for out-of-bound UAHC register access:
* [59:58] = chipID
* [57] = Request source: 0 = core, 1 = NCB-device
* [56:51] = Core/NCB-device number, [56] always 0 for NCB devices
* [50:48] = SubID
*/
-# define USBDRD_UCTL_SHIM_CFG_XS_NCB_OOB_OSRC GENMASK(59, 48)
+# define USBDRD_UCTL_SHIM_CFG_XS_NCB_OOB_OSRC GENMASK_ULL(59, 48)
/* Error log for bad UAHC DMA access: 0 = Read log, 1 = Write log */
-# define USBDRD_UCTL_SHIM_CFG_XM_BAD_DMA_WRN BIT(47)
+# define USBDRD_UCTL_SHIM_CFG_XM_BAD_DMA_WRN BIT_ULL(47)
/* Encoded error type for bad UAHC DMA */
-# define USBDRD_UCTL_SHIM_CFG_XM_BAD_DMA_TYPE GENMASK(43, 40)
+# define USBDRD_UCTL_SHIM_CFG_XM_BAD_DMA_TYPE GENMASK_ULL(43, 40)
/* Select the IOI read command used by DMA accesses */
-# define USBDRD_UCTL_SHIM_CFG_DMA_READ_CMD BIT(12)
+# define USBDRD_UCTL_SHIM_CFG_DMA_READ_CMD BIT_ULL(12)
/* Select endian format for DMA accesses to the L2C:
* 0x0 = Little endian
* 0x1 = Big endian
* 0x2 = Reserved
* 0x3 = Reserved
*/
-# define USBDRD_UCTL_SHIM_CFG_DMA_ENDIAN_MODE GENMASK(9, 8)
+# define USBDRD_UCTL_SHIM_CFG_DMA_ENDIAN_MODE GENMASK_ULL(9, 8)
/* Select endian format for IOI CSR access to UAHC:
* 0x0 = Little endian
* 0x1 = Big endian
* 0x2 = Reserved
* 0x3 = Reserved
*/
-# define USBDRD_UCTL_SHIM_CFG_CSR_ENDIAN_MODE GENMASK(1, 0)
+# define USBDRD_UCTL_SHIM_CFG_CSR_ENDIAN_MODE GENMASK_ULL(1, 0)
#define USBDRD_UCTL_ECC 0xf0
#define USBDRD_UCTL_SPARE1 0xf8
projects / platform / kernel / linux-starfive.git / commitdiff