AIOP_INTR_BIT_3
};
+#ifdef CONFIG_PCI
static Word_t upci_aiop_intr_bits[AIOP_CTL_SIZE] = {
UPCI_AIOP_INTR_BIT_0,
UPCI_AIOP_INTR_BIT_1,
UPCI_AIOP_INTR_BIT_2,
UPCI_AIOP_INTR_BIT_3
};
+#endif
static Byte_t RData[RDATASIZE] = {
0x00, 0x09, 0xf6, 0x82,
static int __init init_ISA(int i);
static void rp_wait_until_sent(struct tty_struct *tty, int timeout);
static void rp_flush_buffer(struct tty_struct *tty);
-static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model);
static unsigned char GetLineNumber(int ctrl, int aiop, int ch);
static unsigned char SetLineNumber(int ctrl, int aiop, int ch);
static void rp_start(struct tty_struct *tty);
static void sModemReset(CONTROLLER_T * CtlP, int chan, int on);
static void sPCIModemReset(CONTROLLER_T * CtlP, int chan, int on);
static int sWriteTxPrioByte(CHANNEL_T * ChP, Byte_t Data);
-static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
- ByteIO_t * AiopIOList, int AiopIOListSize,
- WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
- int PeriodicOnly, int altChanRingIndicator,
- int UPCIRingInd);
static int sInitController(CONTROLLER_T * CtlP, int CtlNum, ByteIO_t MudbacIO,
ByteIO_t * AiopIOList, int AiopIOListSize,
int IRQNum, Byte_t Frequency, int PeriodicOnly);
};
MODULE_DEVICE_TABLE(pci, rocket_pci_ids);
+/* Resets the speaker controller on RocketModem II and III devices */
+static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model)
+{
+ ByteIO_t addr;
+
+ /* RocketModem II speaker control is at the 8th port location of offset 0x40 */
+ if ((model == MODEL_RP4M) || (model == MODEL_RP6M)) {
+ addr = CtlP->AiopIO[0] + 0x4F;
+ sOutB(addr, 0);
+ }
+
+ /* RocketModem III speaker control is at the 1st port location of offset 0x80 */
+ if ((model == MODEL_UPCI_RM3_8PORT)
+ || (model == MODEL_UPCI_RM3_4PORT)) {
+ addr = CtlP->AiopIO[0] + 0x88;
+ sOutB(addr, 0);
+ }
+}
+
+/***************************************************************************
+Function: sPCIInitController
+Purpose: Initialization of controller global registers and controller
+ structure.
+Call: sPCIInitController(CtlP,CtlNum,AiopIOList,AiopIOListSize,
+ IRQNum,Frequency,PeriodicOnly)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+ int CtlNum; Controller number
+ ByteIO_t *AiopIOList; List of I/O addresses for each AIOP.
+ This list must be in the order the AIOPs will be found on the
+ controller. Once an AIOP in the list is not found, it is
+ assumed that there are no more AIOPs on the controller.
+ int AiopIOListSize; Number of addresses in AiopIOList
+ int IRQNum; Interrupt Request number. Can be any of the following:
+ 0: Disable global interrupts
+ 3: IRQ 3
+ 4: IRQ 4
+ 5: IRQ 5
+ 9: IRQ 9
+ 10: IRQ 10
+ 11: IRQ 11
+ 12: IRQ 12
+ 15: IRQ 15
+ Byte_t Frequency: A flag identifying the frequency
+ of the periodic interrupt, can be any one of the following:
+ FREQ_DIS - periodic interrupt disabled
+ FREQ_137HZ - 137 Hertz
+ FREQ_69HZ - 69 Hertz
+ FREQ_34HZ - 34 Hertz
+ FREQ_17HZ - 17 Hertz
+ FREQ_9HZ - 9 Hertz
+ FREQ_4HZ - 4 Hertz
+ If IRQNum is set to 0 the Frequency parameter is
+ overidden, it is forced to a value of FREQ_DIS.
+ int PeriodicOnly: 1 if all interrupts except the periodic
+ interrupt are to be blocked.
+ 0 is both the periodic interrupt and
+ other channel interrupts are allowed.
+ If IRQNum is set to 0 the PeriodicOnly parameter is
+ overidden, it is forced to a value of 0.
+Return: int: Number of AIOPs on the controller, or CTLID_NULL if controller
+ initialization failed.
+
+Comments:
+ If periodic interrupts are to be disabled but AIOP interrupts
+ are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
+
+ If interrupts are to be completely disabled set IRQNum to 0.
+
+ Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
+ invalid combination.
+
+ This function performs initialization of global interrupt modes,
+ but it does not actually enable global interrupts. To enable
+ and disable global interrupts use functions sEnGlobalInt() and
+ sDisGlobalInt(). Enabling of global interrupts is normally not
+ done until all other initializations are complete.
+
+ Even if interrupts are globally enabled, they must also be
+ individually enabled for each channel that is to generate
+ interrupts.
+
+Warnings: No range checking on any of the parameters is done.
+
+ No context switches are allowed while executing this function.
+
+ After this function all AIOPs on the controller are disabled,
+ they can be enabled with sEnAiop().
+*/
+static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
+ ByteIO_t * AiopIOList, int AiopIOListSize,
+ WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
+ int PeriodicOnly, int altChanRingIndicator,
+ int UPCIRingInd)
+{
+ int i;
+ ByteIO_t io;
+
+ CtlP->AltChanRingIndicator = altChanRingIndicator;
+ CtlP->UPCIRingInd = UPCIRingInd;
+ CtlP->CtlNum = CtlNum;
+ CtlP->CtlID = CTLID_0001; /* controller release 1 */
+ CtlP->BusType = isPCI; /* controller release 1 */
+
+ if (ConfigIO) {
+ CtlP->isUPCI = 1;
+ CtlP->PCIIO = ConfigIO + _PCI_9030_INT_CTRL;
+ CtlP->PCIIO2 = ConfigIO + _PCI_9030_GPIO_CTRL;
+ CtlP->AiopIntrBits = upci_aiop_intr_bits;
+ } else {
+ CtlP->isUPCI = 0;
+ CtlP->PCIIO =
+ (WordIO_t) ((ByteIO_t) AiopIOList[0] + _PCI_INT_FUNC);
+ CtlP->AiopIntrBits = aiop_intr_bits;
+ }
+
+ sPCIControllerEOI(CtlP); /* clear EOI if warm init */
+ /* Init AIOPs */
+ CtlP->NumAiop = 0;
+ for (i = 0; i < AiopIOListSize; i++) {
+ io = AiopIOList[i];
+ CtlP->AiopIO[i] = (WordIO_t) io;
+ CtlP->AiopIntChanIO[i] = io + _INT_CHAN;
+
+ CtlP->AiopID[i] = sReadAiopID(io); /* read AIOP ID */
+ if (CtlP->AiopID[i] == AIOPID_NULL) /* if AIOP does not exist */
+ break; /* done looking for AIOPs */
+
+ CtlP->AiopNumChan[i] = sReadAiopNumChan((WordIO_t) io); /* num channels in AIOP */
+ sOutW((WordIO_t) io + _INDX_ADDR, _CLK_PRE); /* clock prescaler */
+ sOutB(io + _INDX_DATA, sClockPrescale);
+ CtlP->NumAiop++; /* bump count of AIOPs */
+ }
+
+ if (CtlP->NumAiop == 0)
+ return (-1);
+ else
+ return (CtlP->NumAiop);
+}
+
/*
* Called when a PCI card is found. Retrieves and stores model information,
* init's aiopic and serial port hardware.
return (CtlP->NumAiop);
}
-#ifdef CONFIG_PCI
-/***************************************************************************
-Function: sPCIInitController
-Purpose: Initialization of controller global registers and controller
- structure.
-Call: sPCIInitController(CtlP,CtlNum,AiopIOList,AiopIOListSize,
- IRQNum,Frequency,PeriodicOnly)
- CONTROLLER_T *CtlP; Ptr to controller structure
- int CtlNum; Controller number
- ByteIO_t *AiopIOList; List of I/O addresses for each AIOP.
- This list must be in the order the AIOPs will be found on the
- controller. Once an AIOP in the list is not found, it is
- assumed that there are no more AIOPs on the controller.
- int AiopIOListSize; Number of addresses in AiopIOList
- int IRQNum; Interrupt Request number. Can be any of the following:
- 0: Disable global interrupts
- 3: IRQ 3
- 4: IRQ 4
- 5: IRQ 5
- 9: IRQ 9
- 10: IRQ 10
- 11: IRQ 11
- 12: IRQ 12
- 15: IRQ 15
- Byte_t Frequency: A flag identifying the frequency
- of the periodic interrupt, can be any one of the following:
- FREQ_DIS - periodic interrupt disabled
- FREQ_137HZ - 137 Hertz
- FREQ_69HZ - 69 Hertz
- FREQ_34HZ - 34 Hertz
- FREQ_17HZ - 17 Hertz
- FREQ_9HZ - 9 Hertz
- FREQ_4HZ - 4 Hertz
- If IRQNum is set to 0 the Frequency parameter is
- overidden, it is forced to a value of FREQ_DIS.
- int PeriodicOnly: 1 if all interrupts except the periodic
- interrupt are to be blocked.
- 0 is both the periodic interrupt and
- other channel interrupts are allowed.
- If IRQNum is set to 0 the PeriodicOnly parameter is
- overidden, it is forced to a value of 0.
-Return: int: Number of AIOPs on the controller, or CTLID_NULL if controller
- initialization failed.
-
-Comments:
- If periodic interrupts are to be disabled but AIOP interrupts
- are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
-
- If interrupts are to be completely disabled set IRQNum to 0.
-
- Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
- invalid combination.
-
- This function performs initialization of global interrupt modes,
- but it does not actually enable global interrupts. To enable
- and disable global interrupts use functions sEnGlobalInt() and
- sDisGlobalInt(). Enabling of global interrupts is normally not
- done until all other initializations are complete.
-
- Even if interrupts are globally enabled, they must also be
- individually enabled for each channel that is to generate
- interrupts.
-
-Warnings: No range checking on any of the parameters is done.
-
- No context switches are allowed while executing this function.
-
- After this function all AIOPs on the controller are disabled,
- they can be enabled with sEnAiop().
-*/
-static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
- ByteIO_t * AiopIOList, int AiopIOListSize,
- WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
- int PeriodicOnly, int altChanRingIndicator,
- int UPCIRingInd)
-{
- int i;
- ByteIO_t io;
-
- CtlP->AltChanRingIndicator = altChanRingIndicator;
- CtlP->UPCIRingInd = UPCIRingInd;
- CtlP->CtlNum = CtlNum;
- CtlP->CtlID = CTLID_0001; /* controller release 1 */
- CtlP->BusType = isPCI; /* controller release 1 */
-
- if (ConfigIO) {
- CtlP->isUPCI = 1;
- CtlP->PCIIO = ConfigIO + _PCI_9030_INT_CTRL;
- CtlP->PCIIO2 = ConfigIO + _PCI_9030_GPIO_CTRL;
- CtlP->AiopIntrBits = upci_aiop_intr_bits;
- } else {
- CtlP->isUPCI = 0;
- CtlP->PCIIO =
- (WordIO_t) ((ByteIO_t) AiopIOList[0] + _PCI_INT_FUNC);
- CtlP->AiopIntrBits = aiop_intr_bits;
- }
-
- sPCIControllerEOI(CtlP); /* clear EOI if warm init */
- /* Init AIOPs */
- CtlP->NumAiop = 0;
- for (i = 0; i < AiopIOListSize; i++) {
- io = AiopIOList[i];
- CtlP->AiopIO[i] = (WordIO_t) io;
- CtlP->AiopIntChanIO[i] = io + _INT_CHAN;
-
- CtlP->AiopID[i] = sReadAiopID(io); /* read AIOP ID */
- if (CtlP->AiopID[i] == AIOPID_NULL) /* if AIOP does not exist */
- break; /* done looking for AIOPs */
-
- CtlP->AiopNumChan[i] = sReadAiopNumChan((WordIO_t) io); /* num channels in AIOP */
- sOutW((WordIO_t) io + _INDX_ADDR, _CLK_PRE); /* clock prescaler */
- sOutB(io + _INDX_DATA, sClockPrescale);
- CtlP->NumAiop++; /* bump count of AIOPs */
- }
-
- if (CtlP->NumAiop == 0)
- return (-1);
- else
- return (CtlP->NumAiop);
-}
-
-/* Resets the speaker controller on RocketModem II and III devices */
-static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model)
-{
- ByteIO_t addr;
-
- /* RocketModem II speaker control is at the 8th port location of offset 0x40 */
- if ((model == MODEL_RP4M) || (model == MODEL_RP6M)) {
- addr = CtlP->AiopIO[0] + 0x4F;
- sOutB(addr, 0);
- }
-
- /* RocketModem III speaker control is at the 1st port location of offset 0x80 */
- if ((model == MODEL_UPCI_RM3_8PORT)
- || (model == MODEL_UPCI_RM3_4PORT)) {
- addr = CtlP->AiopIO[0] + 0x88;
- sOutB(addr, 0);
- }
-}
-#endif
-
/***************************************************************************
Function: sReadAiopID
Purpose: Read the AIOP idenfication number directly from an AIOP.
projects / profile / common / kernel-common.git / commitdiff