i2c: st: Implement bus clear
authorPeter Griffin <peter.griffin@linaro.org>
Wed, 11 May 2016 16:21:59 +0000 (17:21 +0100)
committerWolfram Sang <wsa@the-dreams.de>
Fri, 13 May 2016 10:40:15 +0000 (12:40 +0200)
>From I2C specifications:
      http://www.nxp.com/documents/user_manual/UM10204.pdf

Chapter 3.1.16, when the i2c device held the SDA line low, the master
should send 9 clocks pulses to try to recover.

Signed-off-by: Frederic Pillon <frederic.pillon@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
drivers/i2c/busses/i2c-st.c

index b3c182f..944ec42 100644 (file)
@@ -337,10 +337,42 @@ static void st_i2c_hw_config(struct st_i2c_dev *i2c_dev)
        writel_relaxed(val, i2c_dev->base + SSC_NOISE_SUPP_WIDTH_DATAOUT);
 }
 
+static int st_i2c_recover_bus(struct i2c_adapter *i2c_adap)
+{
+       struct st_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
+       u32 ctl;
+
+       dev_dbg(i2c_dev->dev, "Trying to recover bus\n");
+
+       /*
+        * SSP IP is dual role SPI/I2C to generate 9 clock pulses
+        * we switch to SPI node, 9 bit words and write a 0. This
+        * has been validate with a oscilloscope and is easier
+        * than switching to GPIO mode.
+        */
+
+       /* Disable interrupts */
+       writel_relaxed(0, i2c_dev->base + SSC_IEN);
+
+       st_i2c_hw_config(i2c_dev);
+
+       ctl = SSC_CTL_EN | SSC_CTL_MS | SSC_CTL_EN_RX_FIFO | SSC_CTL_EN_TX_FIFO;
+       st_i2c_set_bits(i2c_dev->base + SSC_CTL, ctl);
+
+       st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_I2CM);
+       usleep_range(8000, 10000);
+
+       writel_relaxed(0, i2c_dev->base + SSC_TBUF);
+       usleep_range(2000, 4000);
+       st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_I2CM);
+
+       return 0;
+}
+
 static int st_i2c_wait_free_bus(struct st_i2c_dev *i2c_dev)
 {
        u32 sta;
-       int i;
+       int i, ret;
 
        for (i = 0; i < 10; i++) {
                sta = readl_relaxed(i2c_dev->base + SSC_STA);
@@ -352,6 +384,12 @@ static int st_i2c_wait_free_bus(struct st_i2c_dev *i2c_dev)
 
        dev_err(i2c_dev->dev, "bus not free (status = 0x%08x)\n", sta);
 
+       ret = i2c_recover_bus(&i2c_dev->adap);
+       if (ret) {
+               dev_err(i2c_dev->dev, "Failed to recover the bus (%d)\n", ret);
+               return ret;
+       }
+
        return -EBUSY;
 }
 
@@ -743,6 +781,10 @@ static struct i2c_algorithm st_i2c_algo = {
        .functionality = st_i2c_func,
 };
 
+static struct i2c_bus_recovery_info st_i2c_recovery_info = {
+       .recover_bus = st_i2c_recover_bus,
+};
+
 static int st_i2c_of_get_deglitch(struct device_node *np,
                struct st_i2c_dev *i2c_dev)
 {
@@ -825,6 +867,7 @@ static int st_i2c_probe(struct platform_device *pdev)
        adap->timeout = 2 * HZ;
        adap->retries = 0;
        adap->algo = &st_i2c_algo;
+       adap->bus_recovery_info = &st_i2c_recovery_info;
        adap->dev.parent = &pdev->dev;
        adap->dev.of_node = pdev->dev.of_node;