help
Enable EXYNOS5440 SoC support
-config EXYNOS_ATAGS
- bool "ATAGS based boot for EXYNOS (deprecated)"
- depends on !ARCH_MULTIPLATFORM
- depends on ATAGS
- default y
- help
- The EXYNOS platform is moving towards being completely probed
- through device tree. This enables support for board files using
- the traditional ATAGS boot format.
- Note that this option is not available for multiplatform builds.
-
-if EXYNOS_ATAGS
-
-config EXYNOS_DEV_DMA
- bool
- help
- Compile in amba device definitions for DMA controller
-
-config EXYNOS4_DEV_AHCI
- bool
- help
- Compile in platform device definitions for AHCI
-
-config EXYNOS4_SETUP_FIMD0
- bool
- help
- Common setup code for FIMD0.
-
-config EXYNOS4_DEV_USB_OHCI
- bool
- help
- Compile in platform device definition for USB OHCI
-
-config EXYNOS4_SETUP_I2C1
- bool
- help
- Common setup code for i2c bus 1.
-
-config EXYNOS4_SETUP_I2C2
- bool
- help
- Common setup code for i2c bus 2.
-
-config EXYNOS4_SETUP_I2C3
- bool
- help
- Common setup code for i2c bus 3.
-
-config EXYNOS4_SETUP_I2C4
- bool
- help
- Common setup code for i2c bus 4.
-
-config EXYNOS4_SETUP_I2C5
- bool
- help
- Common setup code for i2c bus 5.
-
-config EXYNOS4_SETUP_I2C6
- bool
- help
- Common setup code for i2c bus 6.
-
-config EXYNOS4_SETUP_I2C7
- bool
- help
- Common setup code for i2c bus 7.
-
-config EXYNOS4_SETUP_KEYPAD
- bool
- help
- Common setup code for keypad.
-
-config EXYNOS4_SETUP_SDHCI
- bool
- select EXYNOS4_SETUP_SDHCI_GPIO
- help
- Internal helper functions for EXYNOS4 based SDHCI systems.
-
-config EXYNOS4_SETUP_SDHCI_GPIO
- bool
- help
- Common setup code for SDHCI gpio.
-
-config EXYNOS4_SETUP_FIMC
- bool
- help
- Common setup code for the camera interfaces.
-
-config EXYNOS4_SETUP_USB_PHY
- bool
- help
- Common setup code for USB PHY controller
-
-config EXYNOS_SETUP_SPI
- bool
- help
- Common setup code for SPI GPIO configurations.
-
-# machine support
-
-if ARCH_EXYNOS4
-
-comment "EXYNOS4210 Boards"
-
-config MACH_SMDKC210
- bool "SMDKC210"
- select MACH_SMDKV310
- help
- Machine support for Samsung SMDKC210
-
-config MACH_SMDKV310
- bool "SMDKV310"
- select CPU_EXYNOS4210
- select EXYNOS4_DEV_AHCI
- select EXYNOS4_DEV_USB_OHCI
- select EXYNOS4_SETUP_FIMD0
- select EXYNOS4_SETUP_I2C1
- select EXYNOS4_SETUP_KEYPAD
- select EXYNOS4_SETUP_SDHCI
- select EXYNOS4_SETUP_USB_PHY
- select EXYNOS_DEV_DMA
- select EXYNOS_DEV_SYSMMU
- select S3C24XX_PWM
- select S3C_DEV_HSMMC
- select S3C_DEV_HSMMC1
- select S3C_DEV_HSMMC2
- select S3C_DEV_HSMMC3
- select S3C_DEV_I2C1
- select S3C_DEV_RTC
- select S3C_DEV_USB_HSOTG
- select S3C_DEV_WDT
- select S5P_DEV_FIMC0
- select S5P_DEV_FIMC1
- select S5P_DEV_FIMC2
- select S5P_DEV_FIMC3
- select S5P_DEV_FIMD0
- select S5P_DEV_G2D
- select S5P_DEV_I2C_HDMIPHY
- select S5P_DEV_JPEG
- select S5P_DEV_MFC
- select S5P_DEV_TV
- select S5P_DEV_USB_EHCI
- select SAMSUNG_DEV_BACKLIGHT
- select SAMSUNG_DEV_KEYPAD
- select SAMSUNG_DEV_PWM
- help
- Machine support for Samsung SMDKV310
-
-config MACH_ARMLEX4210
- bool "ARMLEX4210"
- select CPU_EXYNOS4210
- select EXYNOS4_DEV_AHCI
- select EXYNOS4_SETUP_SDHCI
- select EXYNOS_DEV_DMA
- select S3C_DEV_HSMMC
- select S3C_DEV_HSMMC2
- select S3C_DEV_HSMMC3
- select S3C_DEV_RTC
- select S3C_DEV_WDT
- help
- Machine support for Samsung ARMLEX4210 based on EXYNOS4210
-
-config MACH_UNIVERSAL_C210
- bool "Mobile UNIVERSAL_C210 Board"
- select CLKSRC_MMIO
- select CLKSRC_SAMSUNG_PWM
- select CPU_EXYNOS4210
- select EXYNOS4_SETUP_FIMC
- select EXYNOS4_SETUP_FIMD0
- select EXYNOS4_SETUP_I2C1
- select EXYNOS4_SETUP_I2C3
- select EXYNOS4_SETUP_I2C5
- select EXYNOS4_SETUP_SDHCI
- select EXYNOS4_SETUP_USB_PHY
- select EXYNOS_DEV_DMA
- select EXYNOS_DEV_SYSMMU
- select S3C_DEV_HSMMC
- select S3C_DEV_HSMMC2
- select S3C_DEV_HSMMC3
- select S3C_DEV_I2C1
- select S3C_DEV_I2C3
- select S3C_DEV_I2C5
- select S3C_DEV_USB_HSOTG
- select S5P_DEV_CSIS0
- select S5P_DEV_FIMC0
- select S5P_DEV_FIMC1
- select S5P_DEV_FIMC2
- select S5P_DEV_FIMC3
- select S5P_DEV_FIMD0
- select S5P_DEV_G2D
- select S5P_DEV_I2C_HDMIPHY
- select S5P_DEV_JPEG
- select S5P_DEV_MFC
- select S5P_DEV_ONENAND
- select S5P_DEV_TV
- select S5P_GPIO_INT
- select S5P_SETUP_MIPIPHY
- help
- Machine support for Samsung Mobile Universal S5PC210 Reference
- Board.
-
-config MACH_NURI
- bool "Mobile NURI Board"
- select CPU_EXYNOS4210
- select EXYNOS4_SETUP_FIMC
- select EXYNOS4_SETUP_FIMD0
- select EXYNOS4_SETUP_I2C1
- select EXYNOS4_SETUP_I2C3
- select EXYNOS4_SETUP_I2C5
- select EXYNOS4_SETUP_I2C6
- select EXYNOS4_SETUP_SDHCI
- select EXYNOS4_SETUP_USB_PHY
- select EXYNOS_DEV_DMA
- select S3C_DEV_HSMMC
- select S3C_DEV_HSMMC2
- select S3C_DEV_HSMMC3
- select S3C_DEV_I2C1
- select S3C_DEV_I2C3
- select S3C_DEV_I2C5
- select S3C_DEV_I2C6
- select S3C_DEV_RTC
- select S3C_DEV_USB_HSOTG
- select S3C_DEV_WDT
- select S5P_DEV_CSIS0
- select S5P_DEV_FIMC0
- select S5P_DEV_FIMC1
- select S5P_DEV_FIMC2
- select S5P_DEV_FIMC3
- select S5P_DEV_FIMD0
- select S5P_DEV_G2D
- select S5P_DEV_JPEG
- select S5P_DEV_MFC
- select S5P_DEV_USB_EHCI
- select S5P_GPIO_INT
- select S5P_SETUP_MIPIPHY
- select SAMSUNG_DEV_ADC
- select SAMSUNG_DEV_PWM
- help
- Machine support for Samsung Mobile NURI Board.
-
-config MACH_ORIGEN
- bool "ORIGEN"
- select CPU_EXYNOS4210
- select EXYNOS4_DEV_USB_OHCI
- select EXYNOS4_SETUP_FIMD0
- select EXYNOS4_SETUP_SDHCI
- select EXYNOS4_SETUP_USB_PHY
- select EXYNOS_DEV_DMA
- select EXYNOS_DEV_SYSMMU
- select S3C24XX_PWM
- select S3C_DEV_HSMMC
- select S3C_DEV_HSMMC2
- select S3C_DEV_RTC
- select S3C_DEV_USB_HSOTG
- select S3C_DEV_WDT
- select S5P_DEV_FIMC0
- select S5P_DEV_FIMC1
- select S5P_DEV_FIMC2
- select S5P_DEV_FIMC3
- select S5P_DEV_FIMD0
- select S5P_DEV_G2D
- select S5P_DEV_I2C_HDMIPHY
- select S5P_DEV_JPEG
- select S5P_DEV_MFC
- select S5P_DEV_TV
- select S5P_DEV_USB_EHCI
- select SAMSUNG_DEV_BACKLIGHT
- select SAMSUNG_DEV_PWM
- help
- Machine support for ORIGEN based on Samsung EXYNOS4210
-
-comment "EXYNOS4212 Boards"
-
-config MACH_SMDK4212
- bool "SMDK4212"
- select EXYNOS4_SETUP_FIMD0
- select EXYNOS4_SETUP_I2C1
- select EXYNOS4_SETUP_I2C3
- select EXYNOS4_SETUP_I2C7
- select EXYNOS4_SETUP_KEYPAD
- select EXYNOS4_SETUP_SDHCI
- select EXYNOS4_SETUP_USB_PHY
- select EXYNOS_DEV_DMA
- select EXYNOS_DEV_SYSMMU
- select S3C24XX_PWM
- select S3C_DEV_HSMMC2
- select S3C_DEV_HSMMC3
- select S3C_DEV_I2C1
- select S3C_DEV_I2C3
- select S3C_DEV_I2C7
- select S3C_DEV_RTC
- select S3C_DEV_USB_HSOTG
- select S3C_DEV_WDT
- select S5P_DEV_FIMC0
- select S5P_DEV_FIMC1
- select S5P_DEV_FIMC2
- select S5P_DEV_FIMC3
- select S5P_DEV_FIMD0
- select S5P_DEV_MFC
- select SAMSUNG_DEV_BACKLIGHT
- select SAMSUNG_DEV_KEYPAD
- select SAMSUNG_DEV_PWM
- select SOC_EXYNOS4212
- help
- Machine support for Samsung SMDK4212
-
-comment "EXYNOS4412 Boards"
-
-config MACH_SMDK4412
- bool "SMDK4412"
- select MACH_SMDK4212
- select SOC_EXYNOS4412
- help
- Machine support for Samsung SMDK4412
-endif
-
-endif
-
comment "Flattened Device Tree based board for EXYNOS SoCs"
config MACH_EXYNOS4_DT
bool "Samsung Exynos4 Machine using device tree"
+ default y
depends on ARCH_EXYNOS4
select ARM_AMBA
select CLKSRC_OF
# machine support
-obj-$(CONFIG_MACH_SMDKC210) += mach-smdkv310.o
-obj-$(CONFIG_MACH_SMDKV310) += mach-smdkv310.o
-obj-$(CONFIG_MACH_ARMLEX4210) += mach-armlex4210.o
-obj-$(CONFIG_MACH_UNIVERSAL_C210) += mach-universal_c210.o
-obj-$(CONFIG_MACH_NURI) += mach-nuri.o
-obj-$(CONFIG_MACH_ORIGEN) += mach-origen.o
-
-obj-$(CONFIG_MACH_SMDK4212) += mach-smdk4x12.o
-obj-$(CONFIG_MACH_SMDK4412) += mach-smdk4x12.o
-
obj-$(CONFIG_MACH_EXYNOS4_DT) += mach-exynos4-dt.o
obj-$(CONFIG_MACH_EXYNOS5_DT) += mach-exynos5-dt.o
obj-y += dev-uart.o
obj-$(CONFIG_ARCH_EXYNOS4) += dev-audio.o
-obj-$(CONFIG_EXYNOS4_DEV_AHCI) += dev-ahci.o
-obj-$(CONFIG_EXYNOS_DEV_DMA) += dma.o
-obj-$(CONFIG_EXYNOS4_DEV_USB_OHCI) += dev-ohci.o
obj-$(CONFIG_ARCH_EXYNOS) += setup-i2c0.o
-obj-$(CONFIG_EXYNOS4_SETUP_FIMC) += setup-fimc.o
-obj-$(CONFIG_EXYNOS4_SETUP_FIMD0) += setup-fimd0.o
-obj-$(CONFIG_EXYNOS4_SETUP_I2C1) += setup-i2c1.o
-obj-$(CONFIG_EXYNOS4_SETUP_I2C2) += setup-i2c2.o
-obj-$(CONFIG_EXYNOS4_SETUP_I2C3) += setup-i2c3.o
-obj-$(CONFIG_EXYNOS4_SETUP_I2C4) += setup-i2c4.o
-obj-$(CONFIG_EXYNOS4_SETUP_I2C5) += setup-i2c5.o
-obj-$(CONFIG_EXYNOS4_SETUP_I2C6) += setup-i2c6.o
-obj-$(CONFIG_EXYNOS4_SETUP_I2C7) += setup-i2c7.o
-obj-$(CONFIG_EXYNOS4_SETUP_KEYPAD) += setup-keypad.o
-obj-$(CONFIG_EXYNOS4_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
-obj-$(CONFIG_EXYNOS4_SETUP_USB_PHY) += setup-usb-phy.o
-obj-$(CONFIG_EXYNOS_SETUP_SPI) += setup-spi.o
exynos_pm_late_initcall();
}
-#ifdef CONFIG_OF
int __init exynos_fdt_map_chipid(unsigned long node, const char *uname,
int depth, void *data)
{
iotable_init(&iodesc, 1);
return 1;
}
-#endif
/*
* exynos_map_io
{
debug_ll_io_init();
-#ifdef CONFIG_OF
if (initial_boot_params)
of_scan_flat_dt(exynos_fdt_map_chipid, NULL);
else
-#endif
iotable_init(exynos_iodesc, ARRAY_SIZE(exynos_iodesc));
if (mach_desc)
};
if (of_have_populated_dt()) {
-#ifdef CONFIG_OF
of_clk_init(NULL);
clocksource_of_init();
-#endif
} else {
/* todo: remove after migrating legacy E4 platforms to dt */
#ifdef CONFIG_ARCH_EXYNOS4
if (!of_have_populated_dt())
gic_init_bases(0, IRQ_PPI(0), S5P_VA_GIC_DIST, S5P_VA_GIC_CPU, gic_bank_offset, NULL);
-#ifdef CONFIG_OF
else
irqchip_init();
-#endif
if (!of_have_populated_dt())
combiner_init(S5P_VA_COMBINER_BASE, NULL,
void __init exynos5_init_irq(void)
{
-#ifdef CONFIG_OF
irqchip_init();
-#endif
gic_arch_extn.irq_set_wake = s3c_irq_wake;
}
+++ /dev/null
-/* linux/arch/arm/mach-exynos4/dev-ahci.c
- *
- * Copyright (c) 2011 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * EXYNOS4 - AHCI support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/ahci_platform.h>
-
-#include <plat/cpu.h>
-
-#include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/regs-pmu.h>
-
-/* PHY Control Register */
-#define SATA_CTRL0 0x0
-/* PHY Link Control Register */
-#define SATA_CTRL1 0x4
-/* PHY Status Register */
-#define SATA_PHY_STATUS 0x8
-
-#define SATA_CTRL0_RX_DATA_VALID(x) (x << 27)
-#define SATA_CTRL0_SPEED_MODE (1 << 26)
-#define SATA_CTRL0_M_PHY_CAL (1 << 19)
-#define SATA_CTRL0_PHY_CMU_RST_N (1 << 10)
-#define SATA_CTRL0_M_PHY_LN_RST_N (1 << 9)
-#define SATA_CTRL0_PHY_POR_N (1 << 8)
-
-#define SATA_CTRL1_RST_PMALIVE_N (1 << 8)
-#define SATA_CTRL1_RST_RXOOB_N (1 << 7)
-#define SATA_CTRL1_RST_RX_N (1 << 6)
-#define SATA_CTRL1_RST_TX_N (1 << 5)
-
-#define SATA_PHY_STATUS_CMU_OK (1 << 18)
-#define SATA_PHY_STATUS_LANE_OK (1 << 16)
-
-#define LANE0 0x200
-#define COM_LANE 0xA00
-
-#define HOST_PORTS_IMPL 0xC
-#define SCLK_SATA_FREQ (67 * MHZ)
-
-static void __iomem *phy_base, *phy_ctrl;
-
-struct phy_reg {
- u8 reg;
- u8 val;
-};
-
-/* SATA PHY setup */
-static const struct phy_reg exynos4_sataphy_cmu[] = {
- { 0x00, 0x06 }, { 0x02, 0x80 }, { 0x22, 0xa0 }, { 0x23, 0x42 },
- { 0x2e, 0x04 }, { 0x2f, 0x50 }, { 0x30, 0x70 }, { 0x31, 0x02 },
- { 0x32, 0x25 }, { 0x33, 0x40 }, { 0x34, 0x01 }, { 0x35, 0x40 },
- { 0x61, 0x2e }, { 0x63, 0x5e }, { 0x65, 0x42 }, { 0x66, 0xd1 },
- { 0x67, 0x20 }, { 0x68, 0x28 }, { 0x69, 0x78 }, { 0x6a, 0x04 },
- { 0x6b, 0xc8 }, { 0x6c, 0x06 },
-};
-
-static const struct phy_reg exynos4_sataphy_lane[] = {
- { 0x00, 0x02 }, { 0x05, 0x10 }, { 0x06, 0x84 }, { 0x07, 0x04 },
- { 0x08, 0xe0 }, { 0x10, 0x23 }, { 0x13, 0x05 }, { 0x14, 0x30 },
- { 0x15, 0x00 }, { 0x17, 0x70 }, { 0x18, 0xf2 }, { 0x19, 0x1e },
- { 0x1a, 0x18 }, { 0x1b, 0x0d }, { 0x1c, 0x08 }, { 0x50, 0x60 },
- { 0x51, 0x0f },
-};
-
-static const struct phy_reg exynos4_sataphy_comlane[] = {
- { 0x01, 0x20 }, { 0x03, 0x40 }, { 0x04, 0x3c }, { 0x05, 0x7d },
- { 0x06, 0x1d }, { 0x07, 0xcf }, { 0x08, 0x05 }, { 0x09, 0x63 },
- { 0x0a, 0x29 }, { 0x0b, 0xc4 }, { 0x0c, 0x01 }, { 0x0d, 0x03 },
- { 0x0e, 0x28 }, { 0x0f, 0x98 }, { 0x10, 0x19 }, { 0x13, 0x80 },
- { 0x14, 0xf0 }, { 0x15, 0xd0 }, { 0x39, 0xa0 }, { 0x3a, 0xa0 },
- { 0x3b, 0xa0 }, { 0x3c, 0xa0 }, { 0x3d, 0xa0 }, { 0x3e, 0xa0 },
- { 0x3f, 0xa0 }, { 0x40, 0x42 }, { 0x42, 0x80 }, { 0x43, 0x58 },
- { 0x45, 0x44 }, { 0x46, 0x5c }, { 0x47, 0x86 }, { 0x48, 0x8d },
- { 0x49, 0xd0 }, { 0x4a, 0x09 }, { 0x4b, 0x90 }, { 0x4c, 0x07 },
- { 0x4d, 0x40 }, { 0x51, 0x20 }, { 0x52, 0x32 }, { 0x7f, 0xd8 },
- { 0x80, 0x1a }, { 0x81, 0xff }, { 0x82, 0x11 }, { 0x83, 0x00 },
- { 0x87, 0xf0 }, { 0x87, 0xff }, { 0x87, 0xff }, { 0x87, 0xff },
- { 0x87, 0xff }, { 0x8c, 0x1c }, { 0x8d, 0xc2 }, { 0x8e, 0xc3 },
- { 0x8f, 0x3f }, { 0x90, 0x0a }, { 0x96, 0xf8 },
-};
-
-static int wait_for_phy_ready(void __iomem *reg, unsigned long bit)
-{
- unsigned long timeout;
-
- /* wait for maximum of 3 sec */
- timeout = jiffies + msecs_to_jiffies(3000);
- while (!(__raw_readl(reg) & bit)) {
- if (time_after(jiffies, timeout))
- return -1;
- cpu_relax();
- }
- return 0;
-}
-
-static int ahci_phy_init(void __iomem *mmio)
-{
- int i, ctrl0;
-
- for (i = 0; i < ARRAY_SIZE(exynos4_sataphy_cmu); i++)
- __raw_writeb(exynos4_sataphy_cmu[i].val,
- phy_base + (exynos4_sataphy_cmu[i].reg * 4));
-
- for (i = 0; i < ARRAY_SIZE(exynos4_sataphy_lane); i++)
- __raw_writeb(exynos4_sataphy_lane[i].val,
- phy_base + (LANE0 + exynos4_sataphy_lane[i].reg) * 4);
-
- for (i = 0; i < ARRAY_SIZE(exynos4_sataphy_comlane); i++)
- __raw_writeb(exynos4_sataphy_comlane[i].val,
- phy_base + (COM_LANE + exynos4_sataphy_comlane[i].reg) * 4);
-
- __raw_writeb(0x07, phy_base);
-
- ctrl0 = __raw_readl(phy_ctrl + SATA_CTRL0);
- ctrl0 |= SATA_CTRL0_PHY_CMU_RST_N;
- __raw_writel(ctrl0, phy_ctrl + SATA_CTRL0);
-
- if (wait_for_phy_ready(phy_ctrl + SATA_PHY_STATUS,
- SATA_PHY_STATUS_CMU_OK) < 0) {
- printk(KERN_ERR "PHY CMU not ready\n");
- return -EBUSY;
- }
-
- __raw_writeb(0x03, phy_base + (COM_LANE * 4));
-
- ctrl0 = __raw_readl(phy_ctrl + SATA_CTRL0);
- ctrl0 |= SATA_CTRL0_M_PHY_LN_RST_N;
- __raw_writel(ctrl0, phy_ctrl + SATA_CTRL0);
-
- if (wait_for_phy_ready(phy_ctrl + SATA_PHY_STATUS,
- SATA_PHY_STATUS_LANE_OK) < 0) {
- printk(KERN_ERR "PHY LANE not ready\n");
- return -EBUSY;
- }
-
- ctrl0 = __raw_readl(phy_ctrl + SATA_CTRL0);
- ctrl0 |= SATA_CTRL0_M_PHY_CAL;
- __raw_writel(ctrl0, phy_ctrl + SATA_CTRL0);
-
- return 0;
-}
-
-static int exynos4_ahci_init(struct device *dev, void __iomem *mmio)
-{
- struct clk *clk_sata, *clk_sataphy, *clk_sclk_sata;
- int val, ret;
-
- phy_base = ioremap(EXYNOS4_PA_SATAPHY, SZ_64K);
- if (!phy_base) {
- dev_err(dev, "failed to allocate memory for SATA PHY\n");
- return -ENOMEM;
- }
-
- phy_ctrl = ioremap(EXYNOS4_PA_SATAPHY_CTRL, SZ_16);
- if (!phy_ctrl) {
- dev_err(dev, "failed to allocate memory for SATA PHY CTRL\n");
- ret = -ENOMEM;
- goto err1;
- }
-
- clk_sata = clk_get(dev, "sata");
- if (IS_ERR(clk_sata)) {
- dev_err(dev, "failed to get sata clock\n");
- ret = PTR_ERR(clk_sata);
- clk_sata = NULL;
- goto err2;
-
- }
- clk_enable(clk_sata);
-
- clk_sataphy = clk_get(dev, "sataphy");
- if (IS_ERR(clk_sataphy)) {
- dev_err(dev, "failed to get sataphy clock\n");
- ret = PTR_ERR(clk_sataphy);
- clk_sataphy = NULL;
- goto err3;
- }
- clk_enable(clk_sataphy);
-
- clk_sclk_sata = clk_get(dev, "sclk_sata");
- if (IS_ERR(clk_sclk_sata)) {
- dev_err(dev, "failed to get sclk_sata\n");
- ret = PTR_ERR(clk_sclk_sata);
- clk_sclk_sata = NULL;
- goto err4;
- }
- clk_enable(clk_sclk_sata);
- clk_set_rate(clk_sclk_sata, SCLK_SATA_FREQ);
-
- __raw_writel(S5P_PMU_SATA_PHY_CONTROL_EN, S5P_PMU_SATA_PHY_CONTROL);
-
- /* Enable PHY link control */
- val = SATA_CTRL1_RST_PMALIVE_N | SATA_CTRL1_RST_RXOOB_N |
- SATA_CTRL1_RST_RX_N | SATA_CTRL1_RST_TX_N;
- __raw_writel(val, phy_ctrl + SATA_CTRL1);
-
- /* Set communication speed as 3Gbps and enable PHY power */
- val = SATA_CTRL0_RX_DATA_VALID(3) | SATA_CTRL0_SPEED_MODE |
- SATA_CTRL0_PHY_POR_N;
- __raw_writel(val, phy_ctrl + SATA_CTRL0);
-
- /* Port0 is available */
- __raw_writel(0x1, mmio + HOST_PORTS_IMPL);
-
- return ahci_phy_init(mmio);
-
-err4:
- clk_disable(clk_sataphy);
- clk_put(clk_sataphy);
-err3:
- clk_disable(clk_sata);
- clk_put(clk_sata);
-err2:
- iounmap(phy_ctrl);
-err1:
- iounmap(phy_base);
-
- return ret;
-}
-
-static struct ahci_platform_data exynos4_ahci_pdata = {
- .init = exynos4_ahci_init,
-};
-
-static struct resource exynos4_ahci_resource[] = {
- [0] = DEFINE_RES_MEM(EXYNOS4_PA_SATA, SZ_64K),
- [1] = DEFINE_RES_IRQ(EXYNOS4_IRQ_SATA),
-};
-
-static u64 exynos4_ahci_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device exynos4_device_ahci = {
- .name = "ahci",
- .id = -1,
- .resource = exynos4_ahci_resource,
- .num_resources = ARRAY_SIZE(exynos4_ahci_resource),
- .dev = {
- .platform_data = &exynos4_ahci_pdata,
- .dma_mask = &exynos4_ahci_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
+++ /dev/null
-/* linux/arch/arm/mach-exynos/dev-ohci.c
- *
- * Copyright (c) 2011 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * EXYNOS - OHCI support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/platform_data/usb-ohci-exynos.h>
-
-#include <mach/irqs.h>
-#include <mach/map.h>
-
-#include <plat/devs.h>
-#include <plat/usb-phy.h>
-
-static struct resource exynos4_ohci_resource[] = {
- [0] = DEFINE_RES_MEM(EXYNOS4_PA_OHCI, SZ_256),
- [1] = DEFINE_RES_IRQ(IRQ_USB_HOST),
-};
-
-static u64 exynos4_ohci_dma_mask = DMA_BIT_MASK(32);
-
-struct platform_device exynos4_device_ohci = {
- .name = "exynos-ohci",
- .id = -1,
- .num_resources = ARRAY_SIZE(exynos4_ohci_resource),
- .resource = exynos4_ohci_resource,
- .dev = {
- .dma_mask = &exynos4_ohci_dma_mask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- }
-};
-
-void __init exynos4_ohci_set_platdata(struct exynos4_ohci_platdata *pd)
-{
- struct exynos4_ohci_platdata *npd;
-
- npd = s3c_set_platdata(pd, sizeof(struct exynos4_ohci_platdata),
- &exynos4_device_ohci);
-
- if (!npd->phy_init)
- npd->phy_init = s5p_usb_phy_init;
- if (!npd->phy_exit)
- npd->phy_exit = s5p_usb_phy_exit;
-}
+++ /dev/null
-/* linux/arch/arm/mach-exynos4/dma.c
- *
- * Copyright (c) 2011 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * Copyright (C) 2010 Samsung Electronics Co. Ltd.
- * Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/pl330.h>
-#include <linux/of.h>
-
-#include <asm/irq.h>
-#include <plat/devs.h>
-#include <plat/irqs.h>
-#include <plat/cpu.h>
-
-#include <mach/map.h>
-#include <mach/irqs.h>
-#include <mach/dma.h>
-
-static u8 exynos4210_pdma0_peri[] = {
- DMACH_PCM0_RX,
- DMACH_PCM0_TX,
- DMACH_PCM2_RX,
- DMACH_PCM2_TX,
- DMACH_MSM_REQ0,
- DMACH_MSM_REQ2,
- DMACH_SPI0_RX,
- DMACH_SPI0_TX,
- DMACH_SPI2_RX,
- DMACH_SPI2_TX,
- DMACH_I2S0S_TX,
- DMACH_I2S0_RX,
- DMACH_I2S0_TX,
- DMACH_I2S2_RX,
- DMACH_I2S2_TX,
- DMACH_UART0_RX,
- DMACH_UART0_TX,
- DMACH_UART2_RX,
- DMACH_UART2_TX,
- DMACH_UART4_RX,
- DMACH_UART4_TX,
- DMACH_SLIMBUS0_RX,
- DMACH_SLIMBUS0_TX,
- DMACH_SLIMBUS2_RX,
- DMACH_SLIMBUS2_TX,
- DMACH_SLIMBUS4_RX,
- DMACH_SLIMBUS4_TX,
- DMACH_AC97_MICIN,
- DMACH_AC97_PCMIN,
- DMACH_AC97_PCMOUT,
-};
-
-static u8 exynos4212_pdma0_peri[] = {
- DMACH_PCM0_RX,
- DMACH_PCM0_TX,
- DMACH_PCM2_RX,
- DMACH_PCM2_TX,
- DMACH_MIPI_HSI0,
- DMACH_MIPI_HSI1,
- DMACH_SPI0_RX,
- DMACH_SPI0_TX,
- DMACH_SPI2_RX,
- DMACH_SPI2_TX,
- DMACH_I2S0S_TX,
- DMACH_I2S0_RX,
- DMACH_I2S0_TX,
- DMACH_I2S2_RX,
- DMACH_I2S2_TX,
- DMACH_UART0_RX,
- DMACH_UART0_TX,
- DMACH_UART2_RX,
- DMACH_UART2_TX,
- DMACH_UART4_RX,
- DMACH_UART4_TX,
- DMACH_SLIMBUS0_RX,
- DMACH_SLIMBUS0_TX,
- DMACH_SLIMBUS2_RX,
- DMACH_SLIMBUS2_TX,
- DMACH_SLIMBUS4_RX,
- DMACH_SLIMBUS4_TX,
- DMACH_AC97_MICIN,
- DMACH_AC97_PCMIN,
- DMACH_AC97_PCMOUT,
- DMACH_MIPI_HSI4,
- DMACH_MIPI_HSI5,
-};
-
-static u8 exynos5250_pdma0_peri[] = {
- DMACH_PCM0_RX,
- DMACH_PCM0_TX,
- DMACH_PCM2_RX,
- DMACH_PCM2_TX,
- DMACH_SPI0_RX,
- DMACH_SPI0_TX,
- DMACH_SPI2_RX,
- DMACH_SPI2_TX,
- DMACH_I2S0S_TX,
- DMACH_I2S0_RX,
- DMACH_I2S0_TX,
- DMACH_I2S2_RX,
- DMACH_I2S2_TX,
- DMACH_UART0_RX,
- DMACH_UART0_TX,
- DMACH_UART2_RX,
- DMACH_UART2_TX,
- DMACH_UART4_RX,
- DMACH_UART4_TX,
- DMACH_SLIMBUS0_RX,
- DMACH_SLIMBUS0_TX,
- DMACH_SLIMBUS2_RX,
- DMACH_SLIMBUS2_TX,
- DMACH_SLIMBUS4_RX,
- DMACH_SLIMBUS4_TX,
- DMACH_AC97_MICIN,
- DMACH_AC97_PCMIN,
- DMACH_AC97_PCMOUT,
- DMACH_MIPI_HSI0,
- DMACH_MIPI_HSI2,
- DMACH_MIPI_HSI4,
- DMACH_MIPI_HSI6,
-};
-
-static struct dma_pl330_platdata exynos_pdma0_pdata;
-
-static AMBA_AHB_DEVICE(exynos_pdma0, "dma-pl330.0", 0x00041330,
- EXYNOS4_PA_PDMA0, {EXYNOS4_IRQ_PDMA0}, &exynos_pdma0_pdata);
-
-static u8 exynos4210_pdma1_peri[] = {
- DMACH_PCM0_RX,
- DMACH_PCM0_TX,
- DMACH_PCM1_RX,
- DMACH_PCM1_TX,
- DMACH_MSM_REQ1,
- DMACH_MSM_REQ3,
- DMACH_SPI1_RX,
- DMACH_SPI1_TX,
- DMACH_I2S0S_TX,
- DMACH_I2S0_RX,
- DMACH_I2S0_TX,
- DMACH_I2S1_RX,
- DMACH_I2S1_TX,
- DMACH_UART0_RX,
- DMACH_UART0_TX,
- DMACH_UART1_RX,
- DMACH_UART1_TX,
- DMACH_UART3_RX,
- DMACH_UART3_TX,
- DMACH_SLIMBUS1_RX,
- DMACH_SLIMBUS1_TX,
- DMACH_SLIMBUS3_RX,
- DMACH_SLIMBUS3_TX,
- DMACH_SLIMBUS5_RX,
- DMACH_SLIMBUS5_TX,
-};
-
-static u8 exynos4212_pdma1_peri[] = {
- DMACH_PCM0_RX,
- DMACH_PCM0_TX,
- DMACH_PCM1_RX,
- DMACH_PCM1_TX,
- DMACH_MIPI_HSI2,
- DMACH_MIPI_HSI3,
- DMACH_SPI1_RX,
- DMACH_SPI1_TX,
- DMACH_I2S0S_TX,
- DMACH_I2S0_RX,
- DMACH_I2S0_TX,
- DMACH_I2S1_RX,
- DMACH_I2S1_TX,
- DMACH_UART0_RX,
- DMACH_UART0_TX,
- DMACH_UART1_RX,
- DMACH_UART1_TX,
- DMACH_UART3_RX,
- DMACH_UART3_TX,
- DMACH_SLIMBUS1_RX,
- DMACH_SLIMBUS1_TX,
- DMACH_SLIMBUS3_RX,
- DMACH_SLIMBUS3_TX,
- DMACH_SLIMBUS5_RX,
- DMACH_SLIMBUS5_TX,
- DMACH_SLIMBUS0AUX_RX,
- DMACH_SLIMBUS0AUX_TX,
- DMACH_SPDIF,
- DMACH_MIPI_HSI6,
- DMACH_MIPI_HSI7,
-};
-
-static u8 exynos5250_pdma1_peri[] = {
- DMACH_PCM0_RX,
- DMACH_PCM0_TX,
- DMACH_PCM1_RX,
- DMACH_PCM1_TX,
- DMACH_SPI1_RX,
- DMACH_SPI1_TX,
- DMACH_PWM,
- DMACH_SPDIF,
- DMACH_I2S0S_TX,
- DMACH_I2S0_RX,
- DMACH_I2S0_TX,
- DMACH_I2S1_RX,
- DMACH_I2S1_TX,
- DMACH_UART0_RX,
- DMACH_UART0_TX,
- DMACH_UART1_RX,
- DMACH_UART1_TX,
- DMACH_UART3_RX,
- DMACH_UART3_TX,
- DMACH_SLIMBUS1_RX,
- DMACH_SLIMBUS1_TX,
- DMACH_SLIMBUS3_RX,
- DMACH_SLIMBUS3_TX,
- DMACH_SLIMBUS5_RX,
- DMACH_SLIMBUS5_TX,
- DMACH_SLIMBUS0AUX_RX,
- DMACH_SLIMBUS0AUX_TX,
- DMACH_DISP1,
- DMACH_MIPI_HSI1,
- DMACH_MIPI_HSI3,
- DMACH_MIPI_HSI5,
- DMACH_MIPI_HSI7,
-};
-
-static struct dma_pl330_platdata exynos_pdma1_pdata;
-
-static AMBA_AHB_DEVICE(exynos_pdma1, "dma-pl330.1", 0x00041330,
- EXYNOS4_PA_PDMA1, {EXYNOS4_IRQ_PDMA1}, &exynos_pdma1_pdata);
-
-static u8 mdma_peri[] = {
- DMACH_MTOM_0,
- DMACH_MTOM_1,
- DMACH_MTOM_2,
- DMACH_MTOM_3,
- DMACH_MTOM_4,
- DMACH_MTOM_5,
- DMACH_MTOM_6,
- DMACH_MTOM_7,
-};
-
-static struct dma_pl330_platdata exynos_mdma1_pdata = {
- .nr_valid_peri = ARRAY_SIZE(mdma_peri),
- .peri_id = mdma_peri,
-};
-
-static AMBA_AHB_DEVICE(exynos_mdma1, "dma-pl330.2", 0x00041330,
- EXYNOS4_PA_MDMA1, {EXYNOS4_IRQ_MDMA1}, &exynos_mdma1_pdata);
-
-static int __init exynos_dma_init(void)
-{
- if (of_have_populated_dt())
- return 0;
-
- if (soc_is_exynos4210()) {
- exynos_pdma0_pdata.nr_valid_peri =
- ARRAY_SIZE(exynos4210_pdma0_peri);
- exynos_pdma0_pdata.peri_id = exynos4210_pdma0_peri;
- exynos_pdma1_pdata.nr_valid_peri =
- ARRAY_SIZE(exynos4210_pdma1_peri);
- exynos_pdma1_pdata.peri_id = exynos4210_pdma1_peri;
-
- if (samsung_rev() == EXYNOS4210_REV_0)
- exynos_mdma1_device.res.start = EXYNOS4_PA_S_MDMA1;
- } else if (soc_is_exynos4212() || soc_is_exynos4412()) {
- exynos_pdma0_pdata.nr_valid_peri =
- ARRAY_SIZE(exynos4212_pdma0_peri);
- exynos_pdma0_pdata.peri_id = exynos4212_pdma0_peri;
- exynos_pdma1_pdata.nr_valid_peri =
- ARRAY_SIZE(exynos4212_pdma1_peri);
- exynos_pdma1_pdata.peri_id = exynos4212_pdma1_peri;
- } else if (soc_is_exynos5250()) {
- exynos_pdma0_pdata.nr_valid_peri =
- ARRAY_SIZE(exynos5250_pdma0_peri);
- exynos_pdma0_pdata.peri_id = exynos5250_pdma0_peri;
- exynos_pdma1_pdata.nr_valid_peri =
- ARRAY_SIZE(exynos5250_pdma1_peri);
- exynos_pdma1_pdata.peri_id = exynos5250_pdma1_peri;
-
- exynos_pdma0_device.res.start = EXYNOS5_PA_PDMA0;
- exynos_pdma0_device.res.end = EXYNOS5_PA_PDMA0 + SZ_4K;
- exynos_pdma0_device.irq[0] = EXYNOS5_IRQ_PDMA0;
- exynos_pdma1_device.res.start = EXYNOS5_PA_PDMA1;
- exynos_pdma1_device.res.end = EXYNOS5_PA_PDMA1 + SZ_4K;
- exynos_pdma0_device.irq[0] = EXYNOS5_IRQ_PDMA1;
- exynos_mdma1_device.res.start = EXYNOS5_PA_MDMA1;
- exynos_mdma1_device.res.end = EXYNOS5_PA_MDMA1 + SZ_4K;
- exynos_pdma0_device.irq[0] = EXYNOS5_IRQ_MDMA1;
- }
-
- dma_cap_set(DMA_SLAVE, exynos_pdma0_pdata.cap_mask);
- dma_cap_set(DMA_CYCLIC, exynos_pdma0_pdata.cap_mask);
- dma_cap_set(DMA_PRIVATE, exynos_pdma0_pdata.cap_mask);
- amba_device_register(&exynos_pdma0_device, &iomem_resource);
-
- dma_cap_set(DMA_SLAVE, exynos_pdma1_pdata.cap_mask);
- dma_cap_set(DMA_CYCLIC, exynos_pdma1_pdata.cap_mask);
- dma_cap_set(DMA_PRIVATE, exynos_pdma1_pdata.cap_mask);
- amba_device_register(&exynos_pdma1_device, &iomem_resource);
-
- dma_cap_set(DMA_MEMCPY, exynos_mdma1_pdata.cap_mask);
- amba_device_register(&exynos_mdma1_device, &iomem_resource);
-
- return 0;
-}
-arch_initcall(exynos_dma_init);
}, \
}
-#ifdef CONFIG_OF
static void exynos_add_device_to_domain(struct exynos_pm_domain *pd,
struct device *dev)
{
return 0;
}
-#else
-static __init int exynos_pm_dt_parse_domains(void)
-{
- return 0;
-}
-#endif /* CONFIG_OF */
static __init __maybe_unused void exynos_pm_add_dev_to_genpd(struct platform_device *pdev,
struct exynos_pm_domain *pd)
projects / platform / kernel / linux-stable.git / commitdiff