void __cvmx_interrupt_gmxx_enable(int interface);
void __cvmx_interrupt_pcsx_intx_en_reg_enable(int index, int block);
void __cvmx_interrupt_pcsxx_int_en_reg_enable(int index);
+
+int __cvmx_helper_xaui_enumerate(int interface)
+{
+ union cvmx_gmxx_hg2_control gmx_hg2_control;
+
+ /* If HiGig2 is enabled return 16 ports, otherwise return 1 port */
+ gmx_hg2_control.u64 = cvmx_read_csr(CVMX_GMXX_HG2_CONTROL(interface));
+ if (gmx_hg2_control.s.hg2tx_en)
+ return 16;
+ else
+ return 1;
+}
+
/**
* Probe a XAUI interface and determine the number of ports
* connected to it. The XAUI interface should still be down
int __cvmx_helper_xaui_probe(int interface)
{
int i;
- union cvmx_gmxx_hg2_control gmx_hg2_control;
union cvmx_gmxx_inf_mode mode;
/*
pko_mem_port_ptrs.s.pid = interface * 16 + i;
cvmx_write_csr(CVMX_PKO_MEM_PORT_PTRS, pko_mem_port_ptrs.u64);
}
-
- /* If HiGig2 is enabled return 16 ports, otherwise return 1 port */
- gmx_hg2_control.u64 = cvmx_read_csr(CVMX_GMXX_HG2_CONTROL(interface));
- if (gmx_hg2_control.s.hg2tx_en)
- return 16;
- else
- return 1;
+ return __cvmx_helper_xaui_enumerate(interface);
}
/**
}
/**
- * This function probes an interface to determine the actual
- * number of hardware ports connected to it. It doesn't setup the
- * ports or enable them. The main goal here is to set the global
- * interface_port_count[interface] correctly. Hardware setup of the
- * ports will be performed later.
+ * This function sets the interface_port_count[interface] correctly,
+ * without modifying any hardware configuration. Hardware setup of
+ * the ports will be performed later.
*
* @interface: Interface to probe
*
* Returns Zero on success, negative on failure
*/
-int cvmx_helper_interface_probe(int interface)
+int cvmx_helper_interface_enumerate(int interface)
{
- /* At this stage in the game we don't want packets to be moving yet.
- The following probe calls should perform hardware setup
- needed to determine port counts. Receive must still be disabled */
switch (cvmx_helper_interface_get_mode(interface)) {
/* These types don't support ports to IPD/PKO */
case CVMX_HELPER_INTERFACE_MODE_DISABLED:
/* XAUI is a single high speed port */
case CVMX_HELPER_INTERFACE_MODE_XAUI:
interface_port_count[interface] =
- __cvmx_helper_xaui_probe(interface);
+ __cvmx_helper_xaui_enumerate(interface);
break;
/*
* RGMII/GMII/MII are all treated about the same. Most
case CVMX_HELPER_INTERFACE_MODE_RGMII:
case CVMX_HELPER_INTERFACE_MODE_GMII:
interface_port_count[interface] =
- __cvmx_helper_rgmii_probe(interface);
+ __cvmx_helper_rgmii_enumerate(interface);
break;
/*
* SPI4 can have 1-16 ports depending on the device at
*/
case CVMX_HELPER_INTERFACE_MODE_SPI:
interface_port_count[interface] =
- __cvmx_helper_spi_probe(interface);
+ __cvmx_helper_spi_enumerate(interface);
break;
/*
* SGMII can have 1-4 ports depending on how many are
case CVMX_HELPER_INTERFACE_MODE_SGMII:
case CVMX_HELPER_INTERFACE_MODE_PICMG:
interface_port_count[interface] =
- __cvmx_helper_sgmii_probe(interface);
+ __cvmx_helper_sgmii_enumerate(interface);
break;
/* PCI target Network Packet Interface */
case CVMX_HELPER_INTERFACE_MODE_NPI:
interface_port_count[interface] =
- __cvmx_helper_npi_probe(interface);
+ __cvmx_helper_npi_enumerate(interface);
break;
/*
* Special loopback only ports. These are not the same
*/
case CVMX_HELPER_INTERFACE_MODE_LOOP:
interface_port_count[interface] =
- __cvmx_helper_loop_probe(interface);
+ __cvmx_helper_loop_enumerate(interface);
break;
}
}
/**
+ * This function probes an interface to determine the actual
+ * number of hardware ports connected to it. It doesn't setup the
+ * ports or enable them. The main goal here is to set the global
+ * interface_port_count[interface] correctly. Hardware setup of the
+ * ports will be performed later.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Zero on success, negative on failure
+ */
+int cvmx_helper_interface_probe(int interface)
+{
+ cvmx_helper_interface_enumerate(interface);
+ /* At this stage in the game we don't want packets to be moving yet.
+ The following probe calls should perform hardware setup
+ needed to determine port counts. Receive must still be disabled */
+ switch (cvmx_helper_interface_get_mode(interface)) {
+ /* These types don't support ports to IPD/PKO */
+ case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+ case CVMX_HELPER_INTERFACE_MODE_PCIE:
+ break;
+ /* XAUI is a single high speed port */
+ case CVMX_HELPER_INTERFACE_MODE_XAUI:
+ __cvmx_helper_xaui_probe(interface);
+ break;
+ /*
+ * RGMII/GMII/MII are all treated about the same. Most
+ * functions refer to these ports as RGMII.
+ */
+ case CVMX_HELPER_INTERFACE_MODE_RGMII:
+ case CVMX_HELPER_INTERFACE_MODE_GMII:
+ __cvmx_helper_rgmii_probe(interface);
+ break;
+ /*
+ * SPI4 can have 1-16 ports depending on the device at
+ * the other end.
+ */
+ case CVMX_HELPER_INTERFACE_MODE_SPI:
+ __cvmx_helper_spi_probe(interface);
+ break;
+ /*
+ * SGMII can have 1-4 ports depending on how many are
+ * hooked up.
+ */
+ case CVMX_HELPER_INTERFACE_MODE_SGMII:
+ case CVMX_HELPER_INTERFACE_MODE_PICMG:
+ __cvmx_helper_sgmii_probe(interface);
+ break;
+ /* PCI target Network Packet Interface */
+ case CVMX_HELPER_INTERFACE_MODE_NPI:
+ __cvmx_helper_npi_probe(interface);
+ break;
+ /*
+ * Special loopback only ports. These are not the same
+ * as other ports in loopback mode.
+ */
+ case CVMX_HELPER_INTERFACE_MODE_LOOP:
+ __cvmx_helper_loop_probe(interface);
+ break;
+ }
+
+ /* Make sure all global variables propagate to other cores */
+ CVMX_SYNCWS;
+
+ return 0;
+}
+
+/**
* Setup the IPD/PIP for the ports on an interface. Packet
* classification and tagging are set for every port on the
* interface. The number of ports on the interface must already
projects / platform / adaptation / renesas_rcar / renesas_kernel.git / commitdiff