help
Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
+config SPI_BCM63XX_HSSPI
+ tristate "Broadcom BCM63XX HS SPI controller driver"
+ depends on BCM63XX || COMPILE_TEST
+ help
+ This enables support for the High Speed SPI controller present on
+ newer Broadcom BCM63XX SoCs.
+
config SPI_BITBANG
tristate "Utilities for Bitbanging SPI masters"
help
tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
depends on ARCH_DAVINCI || ARCH_KEYSTONE
select SPI_BITBANG
- select TI_EDMA
help
SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
config SPI_RSPI
tristate "Renesas RSPI controller"
- depends on (SUPERH || ARCH_SHMOBILE) && SH_DMAE_BASE
+ depends on (SUPERH && SH_DMAE_BASE) || ARCH_SHMOBILE
help
SPI driver for Renesas RSPI blocks.
obj-$(CONFIG_SPI_AU1550) += spi-au1550.o
obj-$(CONFIG_SPI_BCM2835) += spi-bcm2835.o
obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o
+obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o
obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o
obj-$(CONFIG_SPI_BFIN_V3) += spi-bfin-v3.o
obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o
clk_prepare_enable(bs->clk);
- err = request_irq(bs->irq, bcm2835_spi_interrupt, 0,
- dev_name(&pdev->dev), master);
+ err = devm_request_irq(&pdev->dev, bs->irq, bcm2835_spi_interrupt, 0,
+ dev_name(&pdev->dev), master);
if (err) {
dev_err(&pdev->dev, "could not request IRQ: %d\n", err);
goto out_clk_disable;
err = devm_spi_register_master(&pdev->dev, master);
if (err) {
dev_err(&pdev->dev, "could not register SPI master: %d\n", err);
- goto out_free_irq;
+ goto out_clk_disable;
}
return 0;
-out_free_irq:
- free_irq(bs->irq, master);
out_clk_disable:
clk_disable_unprepare(bs->clk);
out_master_put:
struct spi_master *master = platform_get_drvdata(pdev);
struct bcm2835_spi *bs = spi_master_get_devdata(master);
- free_irq(bs->irq, master);
-
/* Clear FIFOs, and disable the HW block */
bcm2835_wr(bs, BCM2835_SPI_CS,
BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX);
--- /dev/null
+/*
+ * Broadcom BCM63XX High Speed SPI Controller driver
+ *
+ * Copyright 2000-2010 Broadcom Corporation
+ * Copyright 2012-2013 Jonas Gorski <jogo@openwrt.org>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/spi/spi.h>
+#include <linux/workqueue.h>
+#include <linux/mutex.h>
+
+#define HSSPI_GLOBAL_CTRL_REG 0x0
+#define GLOBAL_CTRL_CS_POLARITY_SHIFT 0
+#define GLOBAL_CTRL_CS_POLARITY_MASK 0x000000ff
+#define GLOBAL_CTRL_PLL_CLK_CTRL_SHIFT 8
+#define GLOBAL_CTRL_PLL_CLK_CTRL_MASK 0x0000ff00
+#define GLOBAL_CTRL_CLK_GATE_SSOFF BIT(16)
+#define GLOBAL_CTRL_CLK_POLARITY BIT(17)
+#define GLOBAL_CTRL_MOSI_IDLE BIT(18)
+
+#define HSSPI_GLOBAL_EXT_TRIGGER_REG 0x4
+
+#define HSSPI_INT_STATUS_REG 0x8
+#define HSSPI_INT_STATUS_MASKED_REG 0xc
+#define HSSPI_INT_MASK_REG 0x10
+
+#define HSSPI_PINGx_CMD_DONE(i) BIT((i * 8) + 0)
+#define HSSPI_PINGx_RX_OVER(i) BIT((i * 8) + 1)
+#define HSSPI_PINGx_TX_UNDER(i) BIT((i * 8) + 2)
+#define HSSPI_PINGx_POLL_TIMEOUT(i) BIT((i * 8) + 3)
+#define HSSPI_PINGx_CTRL_INVAL(i) BIT((i * 8) + 4)
+
+#define HSSPI_INT_CLEAR_ALL 0xff001f1f
+
+#define HSSPI_PINGPONG_COMMAND_REG(x) (0x80 + (x) * 0x40)
+#define PINGPONG_CMD_COMMAND_MASK 0xf
+#define PINGPONG_COMMAND_NOOP 0
+#define PINGPONG_COMMAND_START_NOW 1
+#define PINGPONG_COMMAND_START_TRIGGER 2
+#define PINGPONG_COMMAND_HALT 3
+#define PINGPONG_COMMAND_FLUSH 4
+#define PINGPONG_CMD_PROFILE_SHIFT 8
+#define PINGPONG_CMD_SS_SHIFT 12
+
+#define HSSPI_PINGPONG_STATUS_REG(x) (0x84 + (x) * 0x40)
+
+#define HSSPI_PROFILE_CLK_CTRL_REG(x) (0x100 + (x) * 0x20)
+#define CLK_CTRL_FREQ_CTRL_MASK 0x0000ffff
+#define CLK_CTRL_SPI_CLK_2X_SEL BIT(14)
+#define CLK_CTRL_ACCUM_RST_ON_LOOP BIT(15)
+
+#define HSSPI_PROFILE_SIGNAL_CTRL_REG(x) (0x104 + (x) * 0x20)
+#define SIGNAL_CTRL_LATCH_RISING BIT(12)
+#define SIGNAL_CTRL_LAUNCH_RISING BIT(13)
+#define SIGNAL_CTRL_ASYNC_INPUT_PATH BIT(16)
+
+#define HSSPI_PROFILE_MODE_CTRL_REG(x) (0x108 + (x) * 0x20)
+#define MODE_CTRL_MULTIDATA_RD_STRT_SHIFT 8
+#define MODE_CTRL_MULTIDATA_WR_STRT_SHIFT 12
+#define MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT 16
+#define MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT 18
+#define MODE_CTRL_MODE_3WIRE BIT(20)
+#define MODE_CTRL_PREPENDBYTE_CNT_SHIFT 24
+
+#define HSSPI_FIFO_REG(x) (0x200 + (x) * 0x200)
+
+
+#define HSSPI_OP_CODE_SHIFT 13
+#define HSSPI_OP_SLEEP (0 << HSSPI_OP_CODE_SHIFT)
+#define HSSPI_OP_READ_WRITE (1 << HSSPI_OP_CODE_SHIFT)
+#define HSSPI_OP_WRITE (2 << HSSPI_OP_CODE_SHIFT)
+#define HSSPI_OP_READ (3 << HSSPI_OP_CODE_SHIFT)
+#define HSSPI_OP_SETIRQ (4 << HSSPI_OP_CODE_SHIFT)
+
+#define HSSPI_BUFFER_LEN 512
+#define HSSPI_OPCODE_LEN 2
+
+#define HSSPI_MAX_PREPEND_LEN 15
+
+#define HSSPI_MAX_SYNC_CLOCK 30000000
+
+#define HSSPI_BUS_NUM 1 /* 0 is legacy SPI */
+
+struct bcm63xx_hsspi {
+ struct completion done;
+ struct mutex bus_mutex;
+
+ struct platform_device *pdev;
+ struct clk *clk;
+ void __iomem *regs;
+ u8 __iomem *fifo;
+
+ u32 speed_hz;
+ u8 cs_polarity;
+};
+
+static void bcm63xx_hsspi_set_cs(struct bcm63xx_hsspi *bs, unsigned cs,
+ bool active)
+{
+ u32 reg;
+
+ mutex_lock(&bs->bus_mutex);
+ reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
+
+ reg &= ~BIT(cs);
+ if (active == !(bs->cs_polarity & BIT(cs)))
+ reg |= BIT(cs);
+
+ __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ mutex_unlock(&bs->bus_mutex);
+}
+
+static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs,
+ struct spi_device *spi, int hz)
+{
+ unsigned profile = spi->chip_select;
+ u32 reg;
+
+ reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz));
+ __raw_writel(CLK_CTRL_ACCUM_RST_ON_LOOP | reg,
+ bs->regs + HSSPI_PROFILE_CLK_CTRL_REG(profile));
+
+ reg = __raw_readl(bs->regs + HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
+ if (hz > HSSPI_MAX_SYNC_CLOCK)
+ reg |= SIGNAL_CTRL_ASYNC_INPUT_PATH;
+ else
+ reg &= ~SIGNAL_CTRL_ASYNC_INPUT_PATH;
+ __raw_writel(reg, bs->regs + HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
+
+ mutex_lock(&bs->bus_mutex);
+ /* setup clock polarity */
+ reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ reg &= ~GLOBAL_CTRL_CLK_POLARITY;
+ if (spi->mode & SPI_CPOL)
+ reg |= GLOBAL_CTRL_CLK_POLARITY;
+ __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ mutex_unlock(&bs->bus_mutex);
+}
+
+static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
+{
+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master);
+ unsigned chip_select = spi->chip_select;
+ u16 opcode = 0;
+ int pending = t->len;
+ int step_size = HSSPI_BUFFER_LEN;
+ const u8 *tx = t->tx_buf;
+ u8 *rx = t->rx_buf;
+
+ bcm63xx_hsspi_set_clk(bs, spi, t->speed_hz);
+ bcm63xx_hsspi_set_cs(bs, spi->chip_select, true);
+
+ if (tx && rx)
+ opcode = HSSPI_OP_READ_WRITE;
+ else if (tx)
+ opcode = HSSPI_OP_WRITE;
+ else if (rx)
+ opcode = HSSPI_OP_READ;
+
+ if (opcode != HSSPI_OP_READ)
+ step_size -= HSSPI_OPCODE_LEN;
+
+ __raw_writel(0 << MODE_CTRL_PREPENDBYTE_CNT_SHIFT |
+ 2 << MODE_CTRL_MULTIDATA_WR_STRT_SHIFT |
+ 2 << MODE_CTRL_MULTIDATA_RD_STRT_SHIFT | 0xff,
+ bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
+
+ while (pending > 0) {
+ int curr_step = min_t(int, step_size, pending);
+
+ init_completion(&bs->done);
+ if (tx) {
+ memcpy_toio(bs->fifo + HSSPI_OPCODE_LEN, tx, curr_step);
+ tx += curr_step;
+ }
+
+ __raw_writew(opcode | curr_step, bs->fifo);
+
+ /* enable interrupt */
+ __raw_writel(HSSPI_PINGx_CMD_DONE(0),
+ bs->regs + HSSPI_INT_MASK_REG);
+
+ /* start the transfer */
+ __raw_writel(!chip_select << PINGPONG_CMD_SS_SHIFT |
+ chip_select << PINGPONG_CMD_PROFILE_SHIFT |
+ PINGPONG_COMMAND_START_NOW,
+ bs->regs + HSSPI_PINGPONG_COMMAND_REG(0));
+
+ if (wait_for_completion_timeout(&bs->done, HZ) == 0) {
+ dev_err(&bs->pdev->dev, "transfer timed out!\n");
+ return -ETIMEDOUT;
+ }
+
+ if (rx) {
+ memcpy_fromio(rx, bs->fifo, curr_step);
+ rx += curr_step;
+ }
+
+ pending -= curr_step;
+ }
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_setup(struct spi_device *spi)
+{
+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master);
+ u32 reg;
+
+ reg = __raw_readl(bs->regs +
+ HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
+ reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING);
+ if (spi->mode & SPI_CPHA)
+ reg |= SIGNAL_CTRL_LAUNCH_RISING;
+ else
+ reg |= SIGNAL_CTRL_LATCH_RISING;
+ __raw_writel(reg, bs->regs +
+ HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
+
+ mutex_lock(&bs->bus_mutex);
+ reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
+
+ /* only change actual polarities if there is no transfer */
+ if ((reg & GLOBAL_CTRL_CS_POLARITY_MASK) == bs->cs_polarity) {
+ if (spi->mode & SPI_CS_HIGH)
+ reg |= BIT(spi->chip_select);
+ else
+ reg &= ~BIT(spi->chip_select);
+ __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ }
+
+ if (spi->mode & SPI_CS_HIGH)
+ bs->cs_polarity |= BIT(spi->chip_select);
+ else
+ bs->cs_polarity &= ~BIT(spi->chip_select);
+
+ mutex_unlock(&bs->bus_mutex);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_transfer_one(struct spi_master *master,
+ struct spi_message *msg)
+{
+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
+ struct spi_transfer *t;
+ struct spi_device *spi = msg->spi;
+ int status = -EINVAL;
+ int dummy_cs;
+ u32 reg;
+
+ /* This controller does not support keeping CS active during idle.
+ * To work around this, we use the following ugly hack:
+ *
+ * a. Invert the target chip select's polarity so it will be active.
+ * b. Select a "dummy" chip select to use as the hardware target.
+ * c. Invert the dummy chip select's polarity so it will be inactive
+ * during the actual transfers.
+ * d. Tell the hardware to send to the dummy chip select. Thanks to
+ * the multiplexed nature of SPI the actual target will receive
+ * the transfer and we see its response.
+ *
+ * e. At the end restore the polarities again to their default values.
+ */
+
+ dummy_cs = !spi->chip_select;
+ bcm63xx_hsspi_set_cs(bs, dummy_cs, true);
+
+ list_for_each_entry(t, &msg->transfers, transfer_list) {
+ status = bcm63xx_hsspi_do_txrx(spi, t);
+ if (status)
+ break;
+
+ msg->actual_length += t->len;
+
+ if (t->delay_usecs)
+ udelay(t->delay_usecs);
+
+ if (t->cs_change)
+ bcm63xx_hsspi_set_cs(bs, spi->chip_select, false);
+ }
+
+ mutex_lock(&bs->bus_mutex);
+ reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ reg &= ~GLOBAL_CTRL_CS_POLARITY_MASK;
+ reg |= bs->cs_polarity;
+ __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ mutex_unlock(&bs->bus_mutex);
+
+ msg->status = status;
+ spi_finalize_current_message(master);
+
+ return 0;
+}
+
+static irqreturn_t bcm63xx_hsspi_interrupt(int irq, void *dev_id)
+{
+ struct bcm63xx_hsspi *bs = (struct bcm63xx_hsspi *)dev_id;
+
+ if (__raw_readl(bs->regs + HSSPI_INT_STATUS_MASKED_REG) == 0)
+ return IRQ_NONE;
+
+ __raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG);
+ __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
+
+ complete(&bs->done);
+
+ return IRQ_HANDLED;
+}
+
+static int bcm63xx_hsspi_probe(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct bcm63xx_hsspi *bs;
+ struct resource *res_mem;
+ void __iomem *regs;
+ struct device *dev = &pdev->dev;
+ struct clk *clk;
+ int irq, ret;
+ u32 reg, rate;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "no irq\n");
+ return -ENXIO;
+ }
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ regs = devm_ioremap_resource(dev, res_mem);
+ if (IS_ERR(regs))
+ return PTR_ERR(regs);
+
+ clk = devm_clk_get(dev, "hsspi");
+
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ rate = clk_get_rate(clk);
+ if (!rate)
+ return -EINVAL;
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ return ret;
+
+ master = spi_alloc_master(&pdev->dev, sizeof(*bs));
+ if (!master) {
+ ret = -ENOMEM;
+ goto out_disable_clk;
+ }
+
+ bs = spi_master_get_devdata(master);
+ bs->pdev = pdev;
+ bs->clk = clk;
+ bs->regs = regs;
+ bs->speed_hz = rate;
+ bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0));
+
+ mutex_init(&bs->bus_mutex);
+
+ master->bus_num = HSSPI_BUS_NUM;
+ master->num_chipselect = 8;
+ master->setup = bcm63xx_hsspi_setup;
+ master->transfer_one_message = bcm63xx_hsspi_transfer_one;
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+ master->bits_per_word_mask = SPI_BPW_MASK(8);
+ master->auto_runtime_pm = true;
+
+ platform_set_drvdata(pdev, master);
+
+ /* Initialize the hardware */
+ __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
+
+ /* clean up any pending interrupts */
+ __raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG);
+
+ /* read out default CS polarities */
+ reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ bs->cs_polarity = reg & GLOBAL_CTRL_CS_POLARITY_MASK;
+ __raw_writel(reg | GLOBAL_CTRL_CLK_GATE_SSOFF,
+ bs->regs + HSSPI_GLOBAL_CTRL_REG);
+
+ ret = devm_request_irq(dev, irq, bcm63xx_hsspi_interrupt, IRQF_SHARED,
+ pdev->name, bs);
+
+ if (ret)
+ goto out_put_master;
+
+ /* register and we are done */
+ ret = devm_spi_register_master(dev, master);
+ if (ret)
+ goto out_put_master;
+
+ return 0;
+
+out_put_master:
+ spi_master_put(master);
+out_disable_clk:
+ clk_disable_unprepare(clk);
+ return ret;
+}
+
+
+static int bcm63xx_hsspi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
+
+ /* reset the hardware and block queue progress */
+ __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
+ clk_disable_unprepare(bs->clk);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int bcm63xx_hsspi_suspend(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
+
+ spi_master_suspend(master);
+ clk_disable_unprepare(bs->clk);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_resume(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
+ int ret;
+
+ ret = clk_prepare_enable(bs->clk);
+ if (ret)
+ return ret;
+
+ spi_master_resume(master);
+
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops bcm63xx_hsspi_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(bcm63xx_hsspi_suspend, bcm63xx_hsspi_resume)
+};
+
+static struct platform_driver bcm63xx_hsspi_driver = {
+ .driver = {
+ .name = "bcm63xx-hsspi",
+ .owner = THIS_MODULE,
+ .pm = &bcm63xx_hsspi_pm_ops,
+ },
+ .probe = bcm63xx_hsspi_probe,
+ .remove = bcm63xx_hsspi_remove,
+};
+
+module_platform_driver(bcm63xx_hsspi_driver);
+
+MODULE_ALIAS("platform:bcm63xx_hsspi");
+MODULE_DESCRIPTION("Broadcom BCM63xx High Speed SPI Controller driver");
+MODULE_AUTHOR("Jonas Gorski <jogo@openwrt.org>");
+MODULE_LICENSE("GPL");
if (!timeout)
return -ETIMEDOUT;
- /* read out all data */
- rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
-
- if (do_rx && rx_tail != len)
- return -EIO;
-
- if (!rx_tail)
+ if (!do_rx)
return 0;
len = 0;
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
dev_err(dev, "no irq\n");
- ret = -ENXIO;
- goto out;
+ return -ENXIO;
}
- clk = clk_get(dev, "spi");
+ clk = devm_clk_get(dev, "spi");
if (IS_ERR(clk)) {
dev_err(dev, "no clock for device\n");
- ret = PTR_ERR(clk);
- goto out;
+ return PTR_ERR(clk);
}
master = spi_alloc_master(dev, sizeof(*bs));
if (!master) {
dev_err(dev, "out of memory\n");
- ret = -ENOMEM;
- goto out_clk;
+ return -ENOMEM;
}
bs = spi_master_get_devdata(master);
}
/* Initialize hardware */
- clk_prepare_enable(bs->clk);
+ ret = clk_prepare_enable(bs->clk);
+ if (ret)
+ goto out_err;
+
bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
/* register and we are done */
clk_disable_unprepare(clk);
out_err:
spi_master_put(master);
-out_clk:
- clk_put(clk);
-out:
return ret;
}
/* HW shutdown */
clk_disable_unprepare(bs->clk);
- clk_put(bs->clk);
return 0;
}
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
static int bcm63xx_spi_suspend(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
{
struct spi_master *master = dev_get_drvdata(dev);
struct bcm63xx_spi *bs = spi_master_get_devdata(master);
+ int ret;
- clk_prepare_enable(bs->clk);
+ ret = clk_prepare_enable(bs->clk);
+ if (ret)
+ return ret;
spi_master_resume(master);
return 0;
}
+#endif
static const struct dev_pm_ops bcm63xx_spi_pm_ops = {
- .suspend = bcm63xx_spi_suspend,
- .resume = bcm63xx_spi_resume,
+ SET_SYSTEM_SLEEP_PM_OPS(bcm63xx_spi_suspend, bcm63xx_spi_resume)
};
-#define BCM63XX_SPI_PM_OPS (&bcm63xx_spi_pm_ops)
-#else
-#define BCM63XX_SPI_PM_OPS NULL
-#endif
-
static struct platform_driver bcm63xx_spi_driver = {
.driver = {
.name = "bcm63xx-spi",
.owner = THIS_MODULE,
- .pm = BCM63XX_SPI_PM_OPS,
+ .pm = &bcm63xx_spi_pm_ops,
},
.probe = bcm63xx_spi_probe,
.remove = bcm63xx_spi_remove,
*
* Since this is software, the timings may not be exactly what your board's
* chips need ... there may be several reasons you'd need to tweak timings
- * in these routines, not just make to make it faster or slower to match a
+ * in these routines, not just to make it faster or slower to match a
* particular CPU clock rate.
*/
/*
* CLPS711X SPI bus driver
*
- * Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru>
+ * Copyright (C) 2012-2014 Alexander Shiyan <shc_work@mail.ru>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
ret = -EINVAL;
goto err_out;
}
- if (gpio_request(hw->chipselect[i], DRIVER_NAME)) {
+ if (devm_gpio_request(&pdev->dev, hw->chipselect[i], NULL)) {
dev_err(&pdev->dev, "Can't get CS GPIO %i\n", i);
ret = -EINVAL;
goto err_out;
dev_err(&pdev->dev, "Failed to register master\n");
err_out:
- while (--i >= 0)
- if (gpio_is_valid(hw->chipselect[i]))
- gpio_free(hw->chipselect[i]);
-
spi_master_put(master);
return ret;
}
-static int spi_clps711x_remove(struct platform_device *pdev)
-{
- int i;
- struct spi_master *master = platform_get_drvdata(pdev);
- struct spi_clps711x_data *hw = spi_master_get_devdata(master);
-
- for (i = 0; i < master->num_chipselect; i++)
- if (gpio_is_valid(hw->chipselect[i]))
- gpio_free(hw->chipselect[i]);
-
- return 0;
-}
-
static struct platform_driver clps711x_spi_driver = {
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
},
.probe = spi_clps711x_probe,
- .remove = spi_clps711x_remove,
};
module_platform_driver(clps711x_spi_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>");
MODULE_DESCRIPTION("CLPS711X SPI bus driver");
+MODULE_ALIAS("platform:" DRIVER_NAME);
mcfqspi = spi_master_get_devdata(master);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_dbg(&pdev->dev, "platform_get_resource failed\n");
- status = -ENXIO;
+ mcfqspi->iobase = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(mcfqspi->iobase)) {
+ status = PTR_ERR(mcfqspi->iobase);
goto fail0;
}
- if (!request_mem_region(res->start, resource_size(res), pdev->name)) {
- dev_dbg(&pdev->dev, "request_mem_region failed\n");
- status = -EBUSY;
- goto fail0;
- }
-
- mcfqspi->iobase = ioremap(res->start, resource_size(res));
- if (!mcfqspi->iobase) {
- dev_dbg(&pdev->dev, "ioremap failed\n");
- status = -ENOMEM;
- goto fail1;
- }
-
mcfqspi->irq = platform_get_irq(pdev, 0);
if (mcfqspi->irq < 0) {
dev_dbg(&pdev->dev, "platform_get_irq failed\n");
status = -ENXIO;
- goto fail2;
+ goto fail0;
}
- status = request_irq(mcfqspi->irq, mcfqspi_irq_handler, 0,
- pdev->name, mcfqspi);
+ status = devm_request_irq(&pdev->dev, mcfqspi->irq, mcfqspi_irq_handler,
+ 0, pdev->name, mcfqspi);
if (status) {
dev_dbg(&pdev->dev, "request_irq failed\n");
- goto fail2;
+ goto fail0;
}
- mcfqspi->clk = clk_get(&pdev->dev, "qspi_clk");
+ mcfqspi->clk = devm_clk_get(&pdev->dev, "qspi_clk");
if (IS_ERR(mcfqspi->clk)) {
dev_dbg(&pdev->dev, "clk_get failed\n");
status = PTR_ERR(mcfqspi->clk);
- goto fail3;
+ goto fail0;
}
clk_enable(mcfqspi->clk);
status = mcfqspi_cs_setup(mcfqspi);
if (status) {
dev_dbg(&pdev->dev, "error initializing cs_control\n");
- goto fail4;
+ goto fail1;
}
init_waitqueue_head(&mcfqspi->waitq);
platform_set_drvdata(pdev, master);
- status = spi_register_master(master);
+ status = devm_spi_register_master(&pdev->dev, master);
if (status) {
dev_dbg(&pdev->dev, "spi_register_master failed\n");
- goto fail5;
+ goto fail2;
}
pm_runtime_enable(mcfqspi->dev);
return 0;
-fail5:
- mcfqspi_cs_teardown(mcfqspi);
-fail4:
- clk_disable(mcfqspi->clk);
- clk_put(mcfqspi->clk);
-fail3:
- free_irq(mcfqspi->irq, mcfqspi);
fail2:
- iounmap(mcfqspi->iobase);
+ mcfqspi_cs_teardown(mcfqspi);
fail1:
- release_mem_region(res->start, resource_size(res));
+ clk_disable(mcfqspi->clk);
fail0:
spi_master_put(master);
mcfqspi_cs_teardown(mcfqspi);
clk_disable(mcfqspi->clk);
- clk_put(mcfqspi->clk);
- free_irq(mcfqspi->irq, mcfqspi);
- iounmap(mcfqspi->iobase);
- release_mem_region(res->start, resource_size(res));
- spi_unregister_master(master);
return 0;
}
dspi = spi_master_get_devdata(spi->master);
pdata = &dspi->pdata;
- /* if bits per word length is zero then set it default 8 */
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
if (!(spi->mode & SPI_NO_CS)) {
if ((pdata->chip_sel == NULL) ||
(pdata->chip_sel[spi->chip_select] == SPI_INTERN_CS))
struct spi_master *master;
struct davinci_spi *dspi;
struct davinci_spi_platform_data *pdata;
- struct resource *r, *mem;
+ struct resource *r;
resource_size_t dma_rx_chan = SPI_NO_RESOURCE;
resource_size_t dma_tx_chan = SPI_NO_RESOURCE;
int i = 0, ret = 0;
dspi->pbase = r->start;
- mem = request_mem_region(r->start, resource_size(r), pdev->name);
- if (mem == NULL) {
- ret = -EBUSY;
+ dspi->base = devm_ioremap_resource(&pdev->dev, r);
+ if (IS_ERR(dspi->base)) {
+ ret = PTR_ERR(dspi->base);
goto free_master;
}
- dspi->base = ioremap(r->start, resource_size(r));
- if (dspi->base == NULL) {
- ret = -ENOMEM;
- goto release_region;
- }
-
dspi->irq = platform_get_irq(pdev, 0);
if (dspi->irq <= 0) {
ret = -EINVAL;
- goto unmap_io;
+ goto free_master;
}
- ret = request_threaded_irq(dspi->irq, davinci_spi_irq, dummy_thread_fn,
- 0, dev_name(&pdev->dev), dspi);
+ ret = devm_request_threaded_irq(&pdev->dev, dspi->irq, davinci_spi_irq,
+ dummy_thread_fn, 0, dev_name(&pdev->dev), dspi);
if (ret)
- goto unmap_io;
+ goto free_master;
dspi->bitbang.master = master;
if (dspi->bitbang.master == NULL) {
ret = -ENODEV;
- goto irq_free;
+ goto free_master;
}
- dspi->clk = clk_get(&pdev->dev, NULL);
+ dspi->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(dspi->clk)) {
ret = -ENODEV;
- goto irq_free;
+ goto free_master;
}
clk_prepare_enable(dspi->clk);
goto free_clk;
dev_info(&pdev->dev, "DMA: supported\n");
- dev_info(&pdev->dev, "DMA: RX channel: %d, TX channel: %d, "
- "event queue: %d\n", dma_rx_chan, dma_tx_chan,
+ dev_info(&pdev->dev, "DMA: RX channel: %pa, TX channel: %pa, "
+ "event queue: %d\n", &dma_rx_chan, &dma_tx_chan,
pdata->dma_event_q);
}
dma_release_channel(dspi->dma_tx);
free_clk:
clk_disable_unprepare(dspi->clk);
- clk_put(dspi->clk);
-irq_free:
- free_irq(dspi->irq, dspi);
-unmap_io:
- iounmap(dspi->base);
-release_region:
- release_mem_region(dspi->pbase, resource_size(r));
free_master:
spi_master_put(master);
err:
{
struct davinci_spi *dspi;
struct spi_master *master;
- struct resource *r;
master = platform_get_drvdata(pdev);
dspi = spi_master_get_devdata(master);
spi_bitbang_stop(&dspi->bitbang);
clk_disable_unprepare(dspi->clk);
- clk_put(dspi->clk);
- free_irq(dspi->irq, dspi);
- iounmap(dspi->base);
- r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(dspi->pbase, resource_size(r));
spi_master_put(master);
return 0;
{
struct dw_spi_mmio *dwsmmio;
struct dw_spi *dws;
- struct resource *mem, *ioarea;
+ struct resource *mem;
int ret;
- dwsmmio = kzalloc(sizeof(struct dw_spi_mmio), GFP_KERNEL);
- if (!dwsmmio) {
- ret = -ENOMEM;
- goto err_end;
- }
+ dwsmmio = devm_kzalloc(&pdev->dev, sizeof(struct dw_spi_mmio),
+ GFP_KERNEL);
+ if (!dwsmmio)
+ return -ENOMEM;
dws = &dwsmmio->dws;
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!mem) {
dev_err(&pdev->dev, "no mem resource?\n");
- ret = -EINVAL;
- goto err_kfree;
+ return -EINVAL;
}
- ioarea = request_mem_region(mem->start, resource_size(mem),
- pdev->name);
- if (!ioarea) {
- dev_err(&pdev->dev, "SPI region already claimed\n");
- ret = -EBUSY;
- goto err_kfree;
- }
-
- dws->regs = ioremap_nocache(mem->start, resource_size(mem));
- if (!dws->regs) {
- dev_err(&pdev->dev, "SPI region already mapped\n");
- ret = -ENOMEM;
- goto err_release_reg;
+ dws->regs = devm_ioremap_resource(&pdev->dev, mem);
+ if (IS_ERR(dws->regs)) {
+ dev_err(&pdev->dev, "SPI region map failed\n");
+ return PTR_ERR(dws->regs);
}
dws->irq = platform_get_irq(pdev, 0);
if (dws->irq < 0) {
dev_err(&pdev->dev, "no irq resource?\n");
- ret = dws->irq; /* -ENXIO */
- goto err_unmap;
+ return dws->irq; /* -ENXIO */
}
- dwsmmio->clk = clk_get(&pdev->dev, NULL);
- if (IS_ERR(dwsmmio->clk)) {
- ret = PTR_ERR(dwsmmio->clk);
- goto err_unmap;
- }
- clk_enable(dwsmmio->clk);
+ dwsmmio->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(dwsmmio->clk))
+ return PTR_ERR(dwsmmio->clk);
+ ret = clk_prepare_enable(dwsmmio->clk);
+ if (ret)
+ return ret;
- dws->parent_dev = &pdev->dev;
dws->bus_num = 0;
dws->num_cs = 4;
dws->max_freq = clk_get_rate(dwsmmio->clk);
- ret = dw_spi_add_host(dws);
+ ret = dw_spi_add_host(&pdev->dev, dws);
if (ret)
- goto err_clk;
+ goto out;
platform_set_drvdata(pdev, dwsmmio);
return 0;
-err_clk:
- clk_disable(dwsmmio->clk);
- clk_put(dwsmmio->clk);
- dwsmmio->clk = NULL;
-err_unmap:
- iounmap(dws->regs);
-err_release_reg:
- release_mem_region(mem->start, resource_size(mem));
-err_kfree:
- kfree(dwsmmio);
-err_end:
+out:
+ clk_disable_unprepare(dwsmmio->clk);
return ret;
}
static int dw_spi_mmio_remove(struct platform_device *pdev)
{
struct dw_spi_mmio *dwsmmio = platform_get_drvdata(pdev);
- struct resource *mem;
-
- clk_disable(dwsmmio->clk);
- clk_put(dwsmmio->clk);
- dwsmmio->clk = NULL;
+ clk_disable_unprepare(dwsmmio->clk);
dw_spi_remove_host(&dwsmmio->dws);
- iounmap(dwsmmio->dws.regs);
- kfree(dwsmmio);
- mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(mem->start, resource_size(mem));
return 0;
}
dev_info(&pdev->dev, "found PCI SPI controller(ID: %04x:%04x)\n",
pdev->vendor, pdev->device);
- ret = pci_enable_device(pdev);
+ ret = pcim_enable_device(pdev);
if (ret)
return ret;
- dwpci = kzalloc(sizeof(struct dw_spi_pci), GFP_KERNEL);
- if (!dwpci) {
- ret = -ENOMEM;
- goto err_disable;
- }
+ dwpci = devm_kzalloc(&pdev->dev, sizeof(struct dw_spi_pci),
+ GFP_KERNEL);
+ if (!dwpci)
+ return -ENOMEM;
dwpci->pdev = pdev;
dws = &dwpci->dws;
/* Get basic io resource and map it */
dws->paddr = pci_resource_start(pdev, pci_bar);
- dws->iolen = pci_resource_len(pdev, pci_bar);
- ret = pci_request_region(pdev, pci_bar, dev_name(&pdev->dev));
+ ret = pcim_iomap_regions(pdev, 1, dev_name(&pdev->dev));
if (ret)
- goto err_kfree;
-
- dws->regs = ioremap_nocache((unsigned long)dws->paddr,
- pci_resource_len(pdev, pci_bar));
- if (!dws->regs) {
- ret = -ENOMEM;
- goto err_release_reg;
- }
+ return ret;
- dws->parent_dev = &pdev->dev;
dws->bus_num = 0;
dws->num_cs = 4;
dws->irq = pdev->irq;
if (pdev->device == 0x0800) {
ret = dw_spi_mid_init(dws);
if (ret)
- goto err_unmap;
+ return ret;
}
- ret = dw_spi_add_host(dws);
+ ret = dw_spi_add_host(&pdev->dev, dws);
if (ret)
- goto err_unmap;
+ return ret;
/* PCI hook and SPI hook use the same drv data */
pci_set_drvdata(pdev, dwpci);
- return 0;
-err_unmap:
- iounmap(dws->regs);
-err_release_reg:
- pci_release_region(pdev, pci_bar);
-err_kfree:
- kfree(dwpci);
-err_disable:
- pci_disable_device(pdev);
- return ret;
+ return 0;
}
static void spi_pci_remove(struct pci_dev *pdev)
struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
dw_spi_remove_host(&dwpci->dws);
- iounmap(dwpci->dws.regs);
- pci_release_region(pdev, 0);
- kfree(dwpci);
- pci_disable_device(pdev);
}
#ifdef CONFIG_PM
dws->tx_end = dws->tx + transfer->len;
dws->rx = transfer->rx_buf;
dws->rx_end = dws->rx + transfer->len;
- dws->cs_change = transfer->cs_change;
dws->len = dws->cur_transfer->len;
if (chip != dws->prev_chip)
cs_change = 1;
/* Only alloc on first setup */
chip = spi_get_ctldata(spi);
if (!chip) {
- chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
+ chip = devm_kzalloc(&spi->dev, sizeof(struct chip_data),
+ GFP_KERNEL);
if (!chip)
return -ENOMEM;
+ spi_set_ctldata(spi, chip);
}
/*
| (spi->mode << SPI_MODE_OFFSET)
| (chip->tmode << SPI_TMOD_OFFSET);
- spi_set_ctldata(spi, chip);
return 0;
}
}
}
-int dw_spi_add_host(struct dw_spi *dws)
+int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
{
struct spi_master *master;
int ret;
BUG_ON(dws == NULL);
- master = spi_alloc_master(dws->parent_dev, 0);
- if (!master) {
- ret = -ENOMEM;
- goto exit;
- }
+ master = spi_alloc_master(dev, 0);
+ if (!master)
+ return -ENOMEM;
dws->master = master;
dws->type = SSI_MOTO_SPI;
snprintf(dws->name, sizeof(dws->name), "dw_spi%d",
dws->bus_num);
- ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED,
+ ret = devm_request_irq(dev, dws->irq, dw_spi_irq, IRQF_SHARED,
dws->name, dws);
if (ret < 0) {
dev_err(&master->dev, "can not get IRQ\n");
}
spi_master_set_devdata(master, dws);
- ret = spi_register_master(master);
+ ret = devm_spi_register_master(dev, master);
if (ret) {
dev_err(&master->dev, "problem registering spi master\n");
goto err_queue_alloc;
dws->dma_ops->dma_exit(dws);
err_diable_hw:
spi_enable_chip(dws, 0);
- free_irq(dws->irq, dws);
err_free_master:
spi_master_put(master);
-exit:
return ret;
}
EXPORT_SYMBOL_GPL(dw_spi_add_host);
spi_enable_chip(dws, 0);
/* Disable clk */
spi_set_clk(dws, 0);
- free_irq(dws->irq, dws);
-
- /* Disconnect from the SPI framework */
- spi_unregister_master(dws->master);
}
EXPORT_SYMBOL_GPL(dw_spi_remove_host);
struct dw_spi {
struct spi_master *master;
struct spi_device *cur_dev;
- struct device *parent_dev;
enum dw_ssi_type type;
char name[16];
void __iomem *regs;
unsigned long paddr;
- u32 iolen;
int irq;
u32 fifo_len; /* depth of the FIFO buffer */
u32 max_freq; /* max bus freq supported */
u8 n_bytes; /* current is a 1/2 bytes op */
u8 max_bits_per_word; /* maxim is 16b */
u32 dma_width;
- int cs_change;
irqreturn_t (*transfer_handler)(struct dw_spi *dws);
void (*cs_control)(u32 command);
void (*cs_control)(u32 command);
};
-extern int dw_spi_add_host(struct dw_spi *dws);
+extern int dw_spi_add_host(struct device *dev, struct dw_spi *dws);
extern void dw_spi_remove_host(struct dw_spi *dws);
extern int dw_spi_suspend_host(struct dw_spi *dws);
extern int dw_spi_resume_host(struct dw_spi *dws);
platform_set_drvdata(pdev, priv);
- ret = spi_register_master(master);
+ ret = devm_spi_register_master(&pdev->dev, master);
if (ret)
spi_master_put(master);
return ret;
}
-static int falcon_sflash_remove(struct platform_device *pdev)
-{
- struct falcon_sflash *priv = platform_get_drvdata(pdev);
-
- spi_unregister_master(priv->master);
-
- return 0;
-}
-
static const struct of_device_id falcon_sflash_match[] = {
{ .compatible = "lantiq,sflash-falcon" },
{},
static struct platform_driver falcon_sflash_driver = {
.probe = falcon_sflash_probe,
- .remove = falcon_sflash_remove,
.driver = {
.name = DRV_NAME,
.owner = THIS_MODULE,
if (!spi->max_speed_hz)
return -EINVAL;
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
return dspi_setup_transfer(spi, NULL);
}
return 0;
}
-static int mxs_spi_setup(struct spi_device *dev)
-{
- if (!dev->bits_per_word)
- dev->bits_per_word = 8;
-
- return 0;
-}
-
static u32 mxs_spi_cs_to_reg(unsigned cs)
{
u32 select = 0;
return -ENOMEM;
master->transfer_one_message = mxs_spi_transfer_one;
- master->setup = mxs_spi_setup;
master->bits_per_word_mask = SPI_BPW_MASK(8);
master->mode_bits = SPI_CPOL | SPI_CPHA;
master->num_chipselect = 3;
#include <linux/spi/spi.h>
#include <linux/spi/rspi.h>
-#define RSPI_SPCR 0x00
-#define RSPI_SSLP 0x01
-#define RSPI_SPPCR 0x02
-#define RSPI_SPSR 0x03
-#define RSPI_SPDR 0x04
-#define RSPI_SPSCR 0x08
-#define RSPI_SPSSR 0x09
-#define RSPI_SPBR 0x0a
-#define RSPI_SPDCR 0x0b
-#define RSPI_SPCKD 0x0c
-#define RSPI_SSLND 0x0d
-#define RSPI_SPND 0x0e
-#define RSPI_SPCR2 0x0f
-#define RSPI_SPCMD0 0x10
-#define RSPI_SPCMD1 0x12
-#define RSPI_SPCMD2 0x14
-#define RSPI_SPCMD3 0x16
-#define RSPI_SPCMD4 0x18
-#define RSPI_SPCMD5 0x1a
-#define RSPI_SPCMD6 0x1c
-#define RSPI_SPCMD7 0x1e
+#define RSPI_SPCR 0x00 /* Control Register */
+#define RSPI_SSLP 0x01 /* Slave Select Polarity Register */
+#define RSPI_SPPCR 0x02 /* Pin Control Register */
+#define RSPI_SPSR 0x03 /* Status Register */
+#define RSPI_SPDR 0x04 /* Data Register */
+#define RSPI_SPSCR 0x08 /* Sequence Control Register */
+#define RSPI_SPSSR 0x09 /* Sequence Status Register */
+#define RSPI_SPBR 0x0a /* Bit Rate Register */
+#define RSPI_SPDCR 0x0b /* Data Control Register */
+#define RSPI_SPCKD 0x0c /* Clock Delay Register */
+#define RSPI_SSLND 0x0d /* Slave Select Negation Delay Register */
+#define RSPI_SPND 0x0e /* Next-Access Delay Register */
+#define RSPI_SPCR2 0x0f /* Control Register 2 */
+#define RSPI_SPCMD0 0x10 /* Command Register 0 */
+#define RSPI_SPCMD1 0x12 /* Command Register 1 */
+#define RSPI_SPCMD2 0x14 /* Command Register 2 */
+#define RSPI_SPCMD3 0x16 /* Command Register 3 */
+#define RSPI_SPCMD4 0x18 /* Command Register 4 */
+#define RSPI_SPCMD5 0x1a /* Command Register 5 */
+#define RSPI_SPCMD6 0x1c /* Command Register 6 */
+#define RSPI_SPCMD7 0x1e /* Command Register 7 */
+#define RSPI_SPBFCR 0x20 /* Buffer Control Register */
+#define RSPI_SPBFDR 0x22 /* Buffer Data Count Setting Register */
/*qspi only */
-#define QSPI_SPBFCR 0x18
-#define QSPI_SPBDCR 0x1a
-#define QSPI_SPBMUL0 0x1c
-#define QSPI_SPBMUL1 0x20
-#define QSPI_SPBMUL2 0x24
-#define QSPI_SPBMUL3 0x28
-
-/* SPCR */
-#define SPCR_SPRIE 0x80
-#define SPCR_SPE 0x40
-#define SPCR_SPTIE 0x20
-#define SPCR_SPEIE 0x10
-#define SPCR_MSTR 0x08
-#define SPCR_MODFEN 0x04
-#define SPCR_TXMD 0x02
-#define SPCR_SPMS 0x01
-
-/* SSLP */
-#define SSLP_SSL1P 0x02
-#define SSLP_SSL0P 0x01
-
-/* SPPCR */
-#define SPPCR_MOIFE 0x20
-#define SPPCR_MOIFV 0x10
+#define QSPI_SPBFCR 0x18 /* Buffer Control Register */
+#define QSPI_SPBDCR 0x1a /* Buffer Data Count Register */
+#define QSPI_SPBMUL0 0x1c /* Transfer Data Length Multiplier Setting Register 0 */
+#define QSPI_SPBMUL1 0x20 /* Transfer Data Length Multiplier Setting Register 1 */
+#define QSPI_SPBMUL2 0x24 /* Transfer Data Length Multiplier Setting Register 2 */
+#define QSPI_SPBMUL3 0x28 /* Transfer Data Length Multiplier Setting Register 3 */
+
+/* SPCR - Control Register */
+#define SPCR_SPRIE 0x80 /* Receive Interrupt Enable */
+#define SPCR_SPE 0x40 /* Function Enable */
+#define SPCR_SPTIE 0x20 /* Transmit Interrupt Enable */
+#define SPCR_SPEIE 0x10 /* Error Interrupt Enable */
+#define SPCR_MSTR 0x08 /* Master/Slave Mode Select */
+#define SPCR_MODFEN 0x04 /* Mode Fault Error Detection Enable */
+/* RSPI on SH only */
+#define SPCR_TXMD 0x02 /* TX Only Mode (vs. Full Duplex) */
+#define SPCR_SPMS 0x01 /* 3-wire Mode (vs. 4-wire) */
+/* QSPI on R-Car M2 only */
+#define SPCR_WSWAP 0x02 /* Word Swap of read-data for DMAC */
+#define SPCR_BSWAP 0x01 /* Byte Swap of read-data for DMAC */
+
+/* SSLP - Slave Select Polarity Register */
+#define SSLP_SSL1P 0x02 /* SSL1 Signal Polarity Setting */
+#define SSLP_SSL0P 0x01 /* SSL0 Signal Polarity Setting */
+
+/* SPPCR - Pin Control Register */
+#define SPPCR_MOIFE 0x20 /* MOSI Idle Value Fixing Enable */
+#define SPPCR_MOIFV 0x10 /* MOSI Idle Fixed Value */
#define SPPCR_SPOM 0x04
-#define SPPCR_SPLP2 0x02
-#define SPPCR_SPLP 0x01
-
-/* SPSR */
-#define SPSR_SPRF 0x80
-#define SPSR_SPTEF 0x20
-#define SPSR_PERF 0x08
-#define SPSR_MODF 0x04
-#define SPSR_IDLNF 0x02
-#define SPSR_OVRF 0x01
-
-/* SPSCR */
-#define SPSCR_SPSLN_MASK 0x07
-
-/* SPSSR */
-#define SPSSR_SPECM_MASK 0x70
-#define SPSSR_SPCP_MASK 0x07
-
-/* SPDCR */
-#define SPDCR_SPLW 0x20
-#define SPDCR_SPRDTD 0x10
+#define SPPCR_SPLP2 0x02 /* Loopback Mode 2 (non-inverting) */
+#define SPPCR_SPLP 0x01 /* Loopback Mode (inverting) */
+
+#define SPPCR_IO3FV 0x04 /* Single-/Dual-SPI Mode IO3 Output Fixed Value */
+#define SPPCR_IO2FV 0x04 /* Single-/Dual-SPI Mode IO2 Output Fixed Value */
+
+/* SPSR - Status Register */
+#define SPSR_SPRF 0x80 /* Receive Buffer Full Flag */
+#define SPSR_TEND 0x40 /* Transmit End */
+#define SPSR_SPTEF 0x20 /* Transmit Buffer Empty Flag */
+#define SPSR_PERF 0x08 /* Parity Error Flag */
+#define SPSR_MODF 0x04 /* Mode Fault Error Flag */
+#define SPSR_IDLNF 0x02 /* RSPI Idle Flag */
+#define SPSR_OVRF 0x01 /* Overrun Error Flag */
+
+/* SPSCR - Sequence Control Register */
+#define SPSCR_SPSLN_MASK 0x07 /* Sequence Length Specification */
+
+/* SPSSR - Sequence Status Register */
+#define SPSSR_SPECM_MASK 0x70 /* Command Error Mask */
+#define SPSSR_SPCP_MASK 0x07 /* Command Pointer Mask */
+
+/* SPDCR - Data Control Register */
+#define SPDCR_TXDMY 0x80 /* Dummy Data Transmission Enable */
+#define SPDCR_SPLW1 0x40 /* Access Width Specification (RZ) */
+#define SPDCR_SPLW0 0x20 /* Access Width Specification (RZ) */
+#define SPDCR_SPLLWORD (SPDCR_SPLW1 | SPDCR_SPLW0)
+#define SPDCR_SPLWORD SPDCR_SPLW1
+#define SPDCR_SPLBYTE SPDCR_SPLW0
+#define SPDCR_SPLW 0x20 /* Access Width Specification (SH) */
+#define SPDCR_SPRDTD 0x10 /* Receive Transmit Data Select */
#define SPDCR_SLSEL1 0x08
#define SPDCR_SLSEL0 0x04
-#define SPDCR_SLSEL_MASK 0x0c
+#define SPDCR_SLSEL_MASK 0x0c /* SSL1 Output Select */
#define SPDCR_SPFC1 0x02
#define SPDCR_SPFC0 0x01
+#define SPDCR_SPFC_MASK 0x03 /* Frame Count Setting (1-4) */
-/* SPCKD */
-#define SPCKD_SCKDL_MASK 0x07
+/* SPCKD - Clock Delay Register */
+#define SPCKD_SCKDL_MASK 0x07 /* Clock Delay Setting (1-8) */
-/* SSLND */
-#define SSLND_SLNDL_MASK 0x07
+/* SSLND - Slave Select Negation Delay Register */
+#define SSLND_SLNDL_MASK 0x07 /* SSL Negation Delay Setting (1-8) */
-/* SPND */
-#define SPND_SPNDL_MASK 0x07
+/* SPND - Next-Access Delay Register */
+#define SPND_SPNDL_MASK 0x07 /* Next-Access Delay Setting (1-8) */
-/* SPCR2 */
-#define SPCR2_PTE 0x08
-#define SPCR2_SPIE 0x04
-#define SPCR2_SPOE 0x02
-#define SPCR2_SPPE 0x01
+/* SPCR2 - Control Register 2 */
+#define SPCR2_PTE 0x08 /* Parity Self-Test Enable */
+#define SPCR2_SPIE 0x04 /* Idle Interrupt Enable */
+#define SPCR2_SPOE 0x02 /* Odd Parity Enable (vs. Even) */
+#define SPCR2_SPPE 0x01 /* Parity Enable */
-/* SPCMDn */
-#define SPCMD_SCKDEN 0x8000
-#define SPCMD_SLNDEN 0x4000
-#define SPCMD_SPNDEN 0x2000
-#define SPCMD_LSBF 0x1000
-#define SPCMD_SPB_MASK 0x0f00
+/* SPCMDn - Command Registers */
+#define SPCMD_SCKDEN 0x8000 /* Clock Delay Setting Enable */
+#define SPCMD_SLNDEN 0x4000 /* SSL Negation Delay Setting Enable */
+#define SPCMD_SPNDEN 0x2000 /* Next-Access Delay Enable */
+#define SPCMD_LSBF 0x1000 /* LSB First */
+#define SPCMD_SPB_MASK 0x0f00 /* Data Length Setting */
#define SPCMD_SPB_8_TO_16(bit) (((bit - 1) << 8) & SPCMD_SPB_MASK)
#define SPCMD_SPB_8BIT 0x0000 /* qspi only */
#define SPCMD_SPB_16BIT 0x0100
#define SPCMD_SPB_20BIT 0x0000
#define SPCMD_SPB_24BIT 0x0100
#define SPCMD_SPB_32BIT 0x0200
-#define SPCMD_SSLKP 0x0080
-#define SPCMD_SSLA_MASK 0x0030
-#define SPCMD_BRDV_MASK 0x000c
-#define SPCMD_CPOL 0x0002
-#define SPCMD_CPHA 0x0001
-
-/* SPBFCR */
-#define SPBFCR_TXRST 0x80 /* qspi only */
-#define SPBFCR_RXRST 0x40 /* qspi only */
+#define SPCMD_SSLKP 0x0080 /* SSL Signal Level Keeping */
+#define SPCMD_SPIMOD_MASK 0x0060 /* SPI Operating Mode (QSPI only) */
+#define SPCMD_SPIMOD1 0x0040
+#define SPCMD_SPIMOD0 0x0020
+#define SPCMD_SPIMOD_SINGLE 0
+#define SPCMD_SPIMOD_DUAL SPCMD_SPIMOD0
+#define SPCMD_SPIMOD_QUAD SPCMD_SPIMOD1
+#define SPCMD_SPRW 0x0010 /* SPI Read/Write Access (Dual/Quad) */
+#define SPCMD_SSLA_MASK 0x0030 /* SSL Assert Signal Setting (RSPI) */
+#define SPCMD_BRDV_MASK 0x000c /* Bit Rate Division Setting */
+#define SPCMD_CPOL 0x0002 /* Clock Polarity Setting */
+#define SPCMD_CPHA 0x0001 /* Clock Phase Setting */
+
+/* SPBFCR - Buffer Control Register */
+#define SPBFCR_TXRST 0x80 /* Transmit Buffer Data Reset (qspi only) */
+#define SPBFCR_RXRST 0x40 /* Receive Buffer Data Reset (qspi only) */
+#define SPBFCR_TXTRG_MASK 0x30 /* Transmit Buffer Data Triggering Number */
+#define SPBFCR_RXTRG_MASK 0x07 /* Receive Buffer Data Triggering Number */
+
+#define DUMMY_DATA 0x00
struct rspi_data {
void __iomem *addr;
wait_queue_head_t wait;
spinlock_t lock;
struct clk *clk;
- unsigned char spsr;
+ u8 spsr;
+ u16 spcmd;
const struct spi_ops *ops;
/* for dmaengine */
unsigned dma_callbacked:1;
};
-static void rspi_write8(struct rspi_data *rspi, u8 data, u16 offset)
+static void rspi_write8(const struct rspi_data *rspi, u8 data, u16 offset)
{
iowrite8(data, rspi->addr + offset);
}
-static void rspi_write16(struct rspi_data *rspi, u16 data, u16 offset)
+static void rspi_write16(const struct rspi_data *rspi, u16 data, u16 offset)
{
iowrite16(data, rspi->addr + offset);
}
-static void rspi_write32(struct rspi_data *rspi, u32 data, u16 offset)
+static void rspi_write32(const struct rspi_data *rspi, u32 data, u16 offset)
{
iowrite32(data, rspi->addr + offset);
}
-static u8 rspi_read8(struct rspi_data *rspi, u16 offset)
+static u8 rspi_read8(const struct rspi_data *rspi, u16 offset)
{
return ioread8(rspi->addr + offset);
}
-static u16 rspi_read16(struct rspi_data *rspi, u16 offset)
+static u16 rspi_read16(const struct rspi_data *rspi, u16 offset)
{
return ioread16(rspi->addr + offset);
}
/* optional functions */
struct spi_ops {
- int (*set_config_register)(struct rspi_data *rspi, int access_size);
+ int (*set_config_register)(const struct rspi_data *rspi,
+ int access_size);
int (*send_pio)(struct rspi_data *rspi, struct spi_message *mesg,
struct spi_transfer *t);
int (*receive_pio)(struct rspi_data *rspi, struct spi_message *mesg,
/*
* functions for RSPI
*/
-static int rspi_set_config_register(struct rspi_data *rspi, int access_size)
+static int rspi_set_config_register(const struct rspi_data *rspi,
+ int access_size)
{
int spbr;
rspi_write8(rspi, 0x00, RSPI_SPCR2);
/* Sets SPCMD */
- rspi_write16(rspi, SPCMD_SPB_8_TO_16(access_size) | SPCMD_SSLKP,
+ rspi_write16(rspi, SPCMD_SPB_8_TO_16(access_size) | rspi->spcmd,
RSPI_SPCMD0);
/* Sets RSPI mode */
/*
* functions for QSPI
*/
-static int qspi_set_config_register(struct rspi_data *rspi, int access_size)
+static int qspi_set_config_register(const struct rspi_data *rspi,
+ int access_size)
{
u16 spcmd;
int spbr;
spcmd = SPCMD_SPB_8BIT;
else if (access_size == 16)
spcmd = SPCMD_SPB_16BIT;
- else if (access_size == 32)
+ else
spcmd = SPCMD_SPB_32BIT;
- spcmd |= SPCMD_SCKDEN | SPCMD_SLNDEN | SPCMD_SSLKP | SPCMD_SPNDEN;
+ spcmd |= SPCMD_SCKDEN | SPCMD_SLNDEN | rspi->spcmd | SPCMD_SPNDEN;
/* Resets transfer data length */
rspi_write32(rspi, 0, QSPI_SPBMUL0);
#define set_config_register(spi, n) spi->ops->set_config_register(spi, n)
-static void rspi_enable_irq(struct rspi_data *rspi, u8 enable)
+static void rspi_enable_irq(const struct rspi_data *rspi, u8 enable)
{
rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) | enable, RSPI_SPCR);
}
-static void rspi_disable_irq(struct rspi_data *rspi, u8 disable)
+static void rspi_disable_irq(const struct rspi_data *rspi, u8 disable)
{
rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) & ~disable, RSPI_SPCR);
}
return 0;
}
-static void rspi_assert_ssl(struct rspi_data *rspi)
+static void rspi_assert_ssl(const struct rspi_data *rspi)
{
rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) | SPCR_SPE, RSPI_SPCR);
}
-static void rspi_negate_ssl(struct rspi_data *rspi)
+static void rspi_negate_ssl(const struct rspi_data *rspi)
{
rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) & ~SPCR_SPE, RSPI_SPCR);
}
struct spi_transfer *t)
{
int remain = t->len;
- u8 *data;
-
- data = (u8 *)t->tx_buf;
+ const u8 *data = t->tx_buf;
while (remain > 0) {
rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) | SPCR_TXMD,
RSPI_SPCR);
remain--;
}
- /* Waiting for the last transmition */
+ /* Waiting for the last transmission */
rspi_wait_for_interrupt(rspi, SPSR_SPTEF, SPCR_SPTIE);
return 0;
struct spi_transfer *t)
{
int remain = t->len;
- u8 *data;
+ const u8 *data = t->tx_buf;
rspi_write8(rspi, SPBFCR_TXRST, QSPI_SPBFCR);
rspi_write8(rspi, 0x00, QSPI_SPBFCR);
- data = (u8 *)t->tx_buf;
while (remain > 0) {
if (rspi_wait_for_interrupt(rspi, SPSR_SPTEF, SPCR_SPTIE) < 0) {
remain--;
}
- /* Waiting for the last transmition */
+ /* Waiting for the last transmission */
rspi_wait_for_interrupt(rspi, SPSR_SPTEF, SPCR_SPTIE);
return 0;
wake_up_interruptible(&rspi->wait);
}
-static int rspi_dma_map_sg(struct scatterlist *sg, void *buf, unsigned len,
- struct dma_chan *chan,
+static int rspi_dma_map_sg(struct scatterlist *sg, const void *buf,
+ unsigned len, struct dma_chan *chan,
enum dma_transfer_direction dir)
{
sg_init_table(sg, 1);
static int rspi_send_dma(struct rspi_data *rspi, struct spi_transfer *t)
{
struct scatterlist sg;
- void *buf = NULL;
+ const void *buf = NULL;
struct dma_async_tx_descriptor *desc;
unsigned len;
int ret = 0;
if (rspi->dma_width_16bit) {
+ void *tmp;
/*
* If DMAC bus width is 16-bit, the driver allocates a dummy
* buffer. And, the driver converts original data into the
* DMAC data: 1st byte, dummy, 2nd byte, dummy ...
*/
len = t->len * 2;
- buf = kmalloc(len, GFP_KERNEL);
- if (!buf)
+ tmp = kmalloc(len, GFP_KERNEL);
+ if (!tmp)
return -ENOMEM;
- rspi_memory_to_8bit(buf, t->tx_buf, t->len);
+ rspi_memory_to_8bit(tmp, t->tx_buf, t->len);
+ buf = tmp;
} else {
len = t->len;
- buf = (void *)t->tx_buf;
+ buf = t->tx_buf;
}
if (!rspi_dma_map_sg(&sg, buf, len, rspi->chan_tx, DMA_TO_DEVICE)) {
return ret;
}
-static void rspi_receive_init(struct rspi_data *rspi)
+static void rspi_receive_init(const struct rspi_data *rspi)
{
- unsigned char spsr;
+ u8 spsr;
spsr = rspi_read8(rspi, RSPI_SPSR);
if (spsr & SPSR_SPRF)
rspi_receive_init(rspi);
- data = (u8 *)t->rx_buf;
+ data = t->rx_buf;
while (remain > 0) {
rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) & ~SPCR_TXMD,
RSPI_SPCR);
return -ETIMEDOUT;
}
/* dummy write for generate clock */
- rspi_write16(rspi, 0x00, RSPI_SPDR);
+ rspi_write16(rspi, DUMMY_DATA, RSPI_SPDR);
if (rspi_wait_for_interrupt(rspi, SPSR_SPRF, SPCR_SPRIE) < 0) {
dev_err(&rspi->master->dev,
return 0;
}
-static void qspi_receive_init(struct rspi_data *rspi)
+static void qspi_receive_init(const struct rspi_data *rspi)
{
- unsigned char spsr;
+ u8 spsr;
spsr = rspi_read8(rspi, RSPI_SPSR);
if (spsr & SPSR_SPRF)
qspi_receive_init(rspi);
- data = (u8 *)t->rx_buf;
+ data = t->rx_buf;
while (remain > 0) {
if (rspi_wait_for_interrupt(rspi, SPSR_SPTEF, SPCR_SPTIE) < 0) {
return -ETIMEDOUT;
}
/* dummy write for generate clock */
- rspi_write8(rspi, 0x00, RSPI_SPDR);
+ rspi_write8(rspi, DUMMY_DATA, RSPI_SPDR);
if (rspi_wait_for_interrupt(rspi, SPSR_SPRF, SPCR_SPRIE) < 0) {
dev_err(&rspi->master->dev,
return ret;
}
-static int rspi_is_dma(struct rspi_data *rspi, struct spi_transfer *t)
+static int rspi_is_dma(const struct rspi_data *rspi, struct spi_transfer *t)
{
if (t->tx_buf && rspi->chan_tx)
return 1;
{
struct rspi_data *rspi = spi_master_get_devdata(spi->master);
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
rspi->max_speed_hz = spi->max_speed_hz;
+ rspi->spcmd = SPCMD_SSLKP;
+ if (spi->mode & SPI_CPOL)
+ rspi->spcmd |= SPCMD_CPOL;
+ if (spi->mode & SPI_CPHA)
+ rspi->spcmd |= SPCMD_CPHA;
+
set_config_register(rspi, 8);
return 0;
static irqreturn_t rspi_irq(int irq, void *_sr)
{
- struct rspi_data *rspi = (struct rspi_data *)_sr;
- unsigned long spsr;
+ struct rspi_data *rspi = _sr;
+ u8 spsr;
irqreturn_t ret = IRQ_NONE;
- unsigned char disable_irq = 0;
+ u8 disable_irq = 0;
rspi->spsr = spsr = rspi_read8(rspi, RSPI_SPSR);
if (spsr & SPSR_SPRF)
static int rspi_request_dma(struct rspi_data *rspi,
struct platform_device *pdev)
{
- struct rspi_plat_data *rspi_pd = dev_get_platdata(&pdev->dev);
+ const struct rspi_plat_data *rspi_pd = dev_get_platdata(&pdev->dev);
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
dma_cap_mask_t mask;
struct dma_slave_config cfg;
{
struct rspi_data *rspi = platform_get_drvdata(pdev);
- spi_unregister_master(rspi->master);
rspi_release_dma(rspi);
- free_irq(platform_get_irq(pdev, 0), rspi);
- clk_put(rspi->clk);
- iounmap(rspi->addr);
+ clk_disable(rspi->clk);
return 0;
}
struct rspi_data *rspi;
int ret, irq;
char clk_name[16];
- struct rspi_plat_data *rspi_pd = pdev->dev.platform_data;
+ const struct rspi_plat_data *rspi_pd = dev_get_platdata(&pdev->dev);
const struct spi_ops *ops;
const struct platform_device_id *id_entry = pdev->id_entry;
dev_err(&pdev->dev, "there is no set_config_register\n");
return -ENODEV;
}
- /* get base addr */
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (unlikely(res == NULL)) {
- dev_err(&pdev->dev, "invalid resource\n");
- return -EINVAL;
- }
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
platform_set_drvdata(pdev, rspi);
rspi->ops = ops;
rspi->master = master;
- rspi->addr = ioremap(res->start, resource_size(res));
- if (rspi->addr == NULL) {
- dev_err(&pdev->dev, "ioremap error.\n");
- ret = -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ rspi->addr = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(rspi->addr)) {
+ ret = PTR_ERR(rspi->addr);
goto error1;
}
snprintf(clk_name, sizeof(clk_name), "%s%d", id_entry->name, pdev->id);
- rspi->clk = clk_get(&pdev->dev, clk_name);
+ rspi->clk = devm_clk_get(&pdev->dev, clk_name);
if (IS_ERR(rspi->clk)) {
dev_err(&pdev->dev, "cannot get clock\n");
ret = PTR_ERR(rspi->clk);
- goto error2;
+ goto error1;
}
clk_enable(rspi->clk);
master->setup = rspi_setup;
master->transfer = rspi_transfer;
master->cleanup = rspi_cleanup;
+ master->mode_bits = SPI_CPHA | SPI_CPOL;
- ret = request_irq(irq, rspi_irq, 0, dev_name(&pdev->dev), rspi);
+ ret = devm_request_irq(&pdev->dev, irq, rspi_irq, 0,
+ dev_name(&pdev->dev), rspi);
if (ret < 0) {
dev_err(&pdev->dev, "request_irq error\n");
- goto error3;
+ goto error2;
}
rspi->irq = irq;
ret = rspi_request_dma(rspi, pdev);
if (ret < 0) {
dev_err(&pdev->dev, "rspi_request_dma failed.\n");
- goto error4;
+ goto error3;
}
- ret = spi_register_master(master);
+ ret = devm_spi_register_master(&pdev->dev, master);
if (ret < 0) {
dev_err(&pdev->dev, "spi_register_master error.\n");
- goto error4;
+ goto error3;
}
dev_info(&pdev->dev, "probed\n");
return 0;
-error4:
- rspi_release_dma(rspi);
- free_irq(irq, rspi);
error3:
- clk_put(rspi->clk);
+ rspi_release_dma(rspi);
error2:
- iounmap(rspi->addr);
+ clk_disable(rspi->clk);
error1:
spi_master_put(master);
static int sc18is602_setup(struct spi_device *spi)
{
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
if (spi->mode & ~(SPI_CPHA | SPI_CPOL | SPI_LSB_FIRST))
return -EINVAL;
master->transfer_one_message = sc18is602_transfer_one;
master->dev.of_node = np;
- error = spi_register_master(master);
+ error = devm_spi_register_master(dev, master);
if (error)
goto error_reg;
return error;
}
-static int sc18is602_remove(struct i2c_client *client)
-{
- struct sc18is602 *hw = i2c_get_clientdata(client);
- struct spi_master *master = hw->master;
-
- spi_unregister_master(master);
-
- return 0;
-}
-
static const struct i2c_device_id sc18is602_id[] = {
{ "sc18is602", sc18is602 },
{ "sc18is602b", sc18is602b },
.name = "sc18is602",
},
.probe = sc18is602_probe,
- .remove = sc18is602_remove,
.id_table = sc18is602_id,
};
{
struct spi_sh_data *ss = spi_master_get_devdata(spi->master);
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
pr_debug("%s: enter\n", __func__);
spi_sh_write(ss, 0xfe, SPI_SH_CR1); /* SPI sycle stop */
static int spi_sirfsoc_setup(struct spi_device *spi)
{
- struct sirfsoc_spi *sspi;
-
if (!spi->max_speed_hz)
return -EINVAL;
- sspi = spi_master_get_devdata(spi->master);
-
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
return spi_sirfsoc_setup_transfer(spi, NULL);
}
static int pch_spi_setup(struct spi_device *pspi)
{
- /* check bits per word */
- if (pspi->bits_per_word == 0) {
- pspi->bits_per_word = 8;
- dev_dbg(&pspi->dev, "%s 8 bits per word\n", __func__);
- }
-
/* Check baud rate setting */
/* if baud rate of chip is greater than
max we can support,return error */
projects / platform / kernel / linux-stable.git / commitdiff