#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <linux/libata.h>
+#include "ahci.h"
#define DRV_NAME "ahci"
#define DRV_VERSION "3.0"
-/* Enclosure Management Control */
-#define EM_CTRL_MSG_TYPE 0x000f0000
-
-/* Enclosure Management LED Message Type */
-#define EM_MSG_LED_HBA_PORT 0x0000000f
-#define EM_MSG_LED_PMP_SLOT 0x0000ff00
-#define EM_MSG_LED_VALUE 0xffff0000
-#define EM_MSG_LED_VALUE_ACTIVITY 0x00070000
-#define EM_MSG_LED_VALUE_OFF 0xfff80000
-#define EM_MSG_LED_VALUE_ON 0x00010000
-
-static int ahci_skip_host_reset;
-static int ahci_ignore_sss;
-
-module_param_named(skip_host_reset, ahci_skip_host_reset, int, 0444);
-MODULE_PARM_DESC(skip_host_reset, "skip global host reset (0=don't skip, 1=skip)");
-
-module_param_named(ignore_sss, ahci_ignore_sss, int, 0444);
-MODULE_PARM_DESC(ignore_sss, "Ignore staggered spinup flag (0=don't ignore, 1=ignore)");
-
-static int ahci_enable_alpm(struct ata_port *ap,
- enum link_pm policy);
-static void ahci_disable_alpm(struct ata_port *ap);
-static ssize_t ahci_led_show(struct ata_port *ap, char *buf);
-static ssize_t ahci_led_store(struct ata_port *ap, const char *buf,
- size_t size);
-static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
- ssize_t size);
-
enum {
AHCI_PCI_BAR = 5,
- AHCI_MAX_PORTS = 32,
- AHCI_MAX_SG = 168, /* hardware max is 64K */
- AHCI_DMA_BOUNDARY = 0xffffffff,
- AHCI_MAX_CMDS = 32,
- AHCI_CMD_SZ = 32,
- AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ,
- AHCI_RX_FIS_SZ = 256,
- AHCI_CMD_TBL_CDB = 0x40,
- AHCI_CMD_TBL_HDR_SZ = 0x80,
- AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16),
- AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS,
- AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ +
- AHCI_RX_FIS_SZ,
- AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ +
- AHCI_CMD_TBL_AR_SZ +
- (AHCI_RX_FIS_SZ * 16),
- AHCI_IRQ_ON_SG = (1 << 31),
- AHCI_CMD_ATAPI = (1 << 5),
- AHCI_CMD_WRITE = (1 << 6),
- AHCI_CMD_PREFETCH = (1 << 7),
- AHCI_CMD_RESET = (1 << 8),
- AHCI_CMD_CLR_BUSY = (1 << 10),
-
- RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
- RX_FIS_SDB = 0x58, /* offset of SDB FIS data */
- RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */
board_ahci = 0,
board_ahci_vt8251 = 1,
board_ahci_nopmp = 7,
board_ahci_yesncq = 8,
board_ahci_nosntf = 9,
-
- /* global controller registers */
- HOST_CAP = 0x00, /* host capabilities */
- HOST_CTL = 0x04, /* global host control */
- HOST_IRQ_STAT = 0x08, /* interrupt status */
- HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */
- HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
- HOST_EM_LOC = 0x1c, /* Enclosure Management location */
- HOST_EM_CTL = 0x20, /* Enclosure Management Control */
- HOST_CAP2 = 0x24, /* host capabilities, extended */
-
- /* HOST_CTL bits */
- HOST_RESET = (1 << 0), /* reset controller; self-clear */
- HOST_IRQ_EN = (1 << 1), /* global IRQ enable */
- HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
-
- /* HOST_CAP bits */
- HOST_CAP_SXS = (1 << 5), /* Supports External SATA */
- HOST_CAP_EMS = (1 << 6), /* Enclosure Management support */
- HOST_CAP_CCC = (1 << 7), /* Command Completion Coalescing */
- HOST_CAP_PART = (1 << 13), /* Partial state capable */
- HOST_CAP_SSC = (1 << 14), /* Slumber state capable */
- HOST_CAP_PIO_MULTI = (1 << 15), /* PIO multiple DRQ support */
- HOST_CAP_FBS = (1 << 16), /* FIS-based switching support */
- HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */
- HOST_CAP_ONLY = (1 << 18), /* Supports AHCI mode only */
- HOST_CAP_CLO = (1 << 24), /* Command List Override support */
- HOST_CAP_LED = (1 << 25), /* Supports activity LED */
- HOST_CAP_ALPM = (1 << 26), /* Aggressive Link PM support */
- HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
- HOST_CAP_MPS = (1 << 28), /* Mechanical presence switch */
- HOST_CAP_SNTF = (1 << 29), /* SNotification register */
- HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
- HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
-
- /* HOST_CAP2 bits */
- HOST_CAP2_BOH = (1 << 0), /* BIOS/OS handoff supported */
- HOST_CAP2_NVMHCI = (1 << 1), /* NVMHCI supported */
- HOST_CAP2_APST = (1 << 2), /* Automatic partial to slumber */
-
- /* registers for each SATA port */
- PORT_LST_ADDR = 0x00, /* command list DMA addr */
- PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */
- PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */
- PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */
- PORT_IRQ_STAT = 0x10, /* interrupt status */
- PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */
- PORT_CMD = 0x18, /* port command */
- PORT_TFDATA = 0x20, /* taskfile data */
- PORT_SIG = 0x24, /* device TF signature */
- PORT_CMD_ISSUE = 0x38, /* command issue */
- PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */
- PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */
- PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
- PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
- PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */
- PORT_FBS = 0x40, /* FIS-based Switching */
-
- /* PORT_IRQ_{STAT,MASK} bits */
- PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
- PORT_IRQ_TF_ERR = (1 << 30), /* task file error */
- PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */
- PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */
- PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */
- PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */
- PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */
- PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
-
- PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
- PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */
- PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
- PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
- PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
- PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */
- PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */
- PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */
- PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */
-
- PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR |
- PORT_IRQ_IF_ERR |
- PORT_IRQ_CONNECT |
- PORT_IRQ_PHYRDY |
- PORT_IRQ_UNK_FIS |
- PORT_IRQ_BAD_PMP,
- PORT_IRQ_ERROR = PORT_IRQ_FREEZE |
- PORT_IRQ_TF_ERR |
- PORT_IRQ_HBUS_DATA_ERR,
- DEF_PORT_IRQ = PORT_IRQ_ERROR | PORT_IRQ_SG_DONE |
- PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS |
- PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
-
- /* PORT_CMD bits */
- PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */
- PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */
- PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
- PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */
- PORT_CMD_PMP = (1 << 17), /* PMP attached */
- PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
- PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
- PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */
- PORT_CMD_CLO = (1 << 3), /* Command list override */
- PORT_CMD_POWER_ON = (1 << 2), /* Power up device */
- PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
- PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
-
- PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */
- PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
- PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
- PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
-
- PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */
- PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
- PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */
- PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */
- PORT_FBS_SDE = (1 << 2), /* FBS single device error */
- PORT_FBS_DEC = (1 << 1), /* FBS device error clear */
- PORT_FBS_EN = (1 << 0), /* Enable FBS */
-
- /* hpriv->flags bits */
- AHCI_HFLAG_NO_NCQ = (1 << 0),
- AHCI_HFLAG_IGN_IRQ_IF_ERR = (1 << 1), /* ignore IRQ_IF_ERR */
- AHCI_HFLAG_IGN_SERR_INTERNAL = (1 << 2), /* ignore SERR_INTERNAL */
- AHCI_HFLAG_32BIT_ONLY = (1 << 3), /* force 32bit */
- AHCI_HFLAG_MV_PATA = (1 << 4), /* PATA port */
- AHCI_HFLAG_NO_MSI = (1 << 5), /* no PCI MSI */
- AHCI_HFLAG_NO_PMP = (1 << 6), /* no PMP */
- AHCI_HFLAG_NO_HOTPLUG = (1 << 7), /* ignore PxSERR.DIAG.N */
- AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */
- AHCI_HFLAG_YES_NCQ = (1 << 9), /* force NCQ cap on */
- AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */
- AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as
- link offline */
- AHCI_HFLAG_NO_SNTF = (1 << 12), /* no sntf */
-
- /* ap->flags bits */
-
- AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
- ATA_FLAG_ACPI_SATA | ATA_FLAG_AN |
- ATA_FLAG_IPM,
-
- ICH_MAP = 0x90, /* ICH MAP register */
-
- /* em constants */
- EM_MAX_SLOTS = 8,
- EM_MAX_RETRY = 5,
-
- /* em_ctl bits */
- EM_CTL_RST = (1 << 9), /* Reset */
- EM_CTL_TM = (1 << 8), /* Transmit Message */
- EM_CTL_ALHD = (1 << 26), /* Activity LED */
-};
-
-struct ahci_cmd_hdr {
- __le32 opts;
- __le32 status;
- __le32 tbl_addr;
- __le32 tbl_addr_hi;
- __le32 reserved[4];
-};
-
-struct ahci_sg {
- __le32 addr;
- __le32 addr_hi;
- __le32 reserved;
- __le32 flags_size;
-};
-
-struct ahci_em_priv {
- enum sw_activity blink_policy;
- struct timer_list timer;
- unsigned long saved_activity;
- unsigned long activity;
- unsigned long led_state;
-};
-
-struct ahci_host_priv {
- void __iomem * mmio; /* bus-independant mem map */
- unsigned int flags; /* AHCI_HFLAG_* */
- u32 cap; /* cap to use */
- u32 cap2; /* cap2 to use */
- u32 port_map; /* port map to use */
- u32 saved_cap; /* saved initial cap */
- u32 saved_cap2; /* saved initial cap2 */
- u32 saved_port_map; /* saved initial port_map */
- u32 em_loc; /* enclosure management location */
-};
-
-struct ahci_port_priv {
- struct ata_link *active_link;
- struct ahci_cmd_hdr *cmd_slot;
- dma_addr_t cmd_slot_dma;
- void *cmd_tbl;
- dma_addr_t cmd_tbl_dma;
- void *rx_fis;
- dma_addr_t rx_fis_dma;
- /* for NCQ spurious interrupt analysis */
- unsigned int ncq_saw_d2h:1;
- unsigned int ncq_saw_dmas:1;
- unsigned int ncq_saw_sdb:1;
- u32 intr_mask; /* interrupts to enable */
- bool fbs_supported; /* set iff FBS is supported */
- bool fbs_enabled; /* set iff FBS is enabled */
- int fbs_last_dev; /* save FBS.DEV of last FIS */
- /* enclosure management info per PM slot */
- struct ahci_em_priv em_priv[EM_MAX_SLOTS];
};
-static int ahci_scr_read(struct ata_link *link, unsigned int sc_reg, u32 *val);
-static int ahci_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val);
static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
-static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc);
-static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc);
-static int ahci_port_start(struct ata_port *ap);
-static void ahci_port_stop(struct ata_port *ap);
-static int ahci_pmp_qc_defer(struct ata_queued_cmd *qc);
-static void ahci_qc_prep(struct ata_queued_cmd *qc);
-static void ahci_freeze(struct ata_port *ap);
-static void ahci_thaw(struct ata_port *ap);
-static void ahci_enable_fbs(struct ata_port *ap);
-static void ahci_disable_fbs(struct ata_port *ap);
-static void ahci_pmp_attach(struct ata_port *ap);
-static void ahci_pmp_detach(struct ata_port *ap);
-static int ahci_softreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline);
static int ahci_sb600_softreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
-static int ahci_hardreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline);
static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
-static void ahci_postreset(struct ata_link *link, unsigned int *class);
-static void ahci_error_handler(struct ata_port *ap);
-static void ahci_post_internal_cmd(struct ata_queued_cmd *qc);
-static int ahci_port_resume(struct ata_port *ap);
-static void ahci_dev_config(struct ata_device *dev);
-static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
- u32 opts);
#ifdef CONFIG_PM
-static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg);
static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
static int ahci_pci_device_resume(struct pci_dev *pdev);
#endif
-static ssize_t ahci_activity_show(struct ata_device *dev, char *buf);
-static ssize_t ahci_activity_store(struct ata_device *dev,
- enum sw_activity val);
-static void ahci_init_sw_activity(struct ata_link *link);
-
-static ssize_t ahci_show_host_caps(struct device *dev,
- struct device_attribute *attr, char *buf);
-static ssize_t ahci_show_host_cap2(struct device *dev,
- struct device_attribute *attr, char *buf);
-static ssize_t ahci_show_host_version(struct device *dev,
- struct device_attribute *attr, char *buf);
-static ssize_t ahci_show_port_cmd(struct device *dev,
- struct device_attribute *attr, char *buf);
-
-static DEVICE_ATTR(ahci_host_caps, S_IRUGO, ahci_show_host_caps, NULL);
-static DEVICE_ATTR(ahci_host_cap2, S_IRUGO, ahci_show_host_cap2, NULL);
-static DEVICE_ATTR(ahci_host_version, S_IRUGO, ahci_show_host_version, NULL);
-static DEVICE_ATTR(ahci_port_cmd, S_IRUGO, ahci_show_port_cmd, NULL);
-
-static struct device_attribute *ahci_shost_attrs[] = {
- &dev_attr_link_power_management_policy,
- &dev_attr_em_message_type,
- &dev_attr_em_message,
- &dev_attr_ahci_host_caps,
- &dev_attr_ahci_host_cap2,
- &dev_attr_ahci_host_version,
- &dev_attr_ahci_port_cmd,
- NULL
-};
-
-static struct device_attribute *ahci_sdev_attrs[] = {
- &dev_attr_sw_activity,
- &dev_attr_unload_heads,
- NULL
-};
-
-static struct scsi_host_template ahci_sht = {
- ATA_NCQ_SHT(DRV_NAME),
- .can_queue = AHCI_MAX_CMDS - 1,
- .sg_tablesize = AHCI_MAX_SG,
- .dma_boundary = AHCI_DMA_BOUNDARY,
- .shost_attrs = ahci_shost_attrs,
- .sdev_attrs = ahci_sdev_attrs,
-};
-
-static struct ata_port_operations ahci_ops = {
- .inherits = &sata_pmp_port_ops,
-
- .qc_defer = ahci_pmp_qc_defer,
- .qc_prep = ahci_qc_prep,
- .qc_issue = ahci_qc_issue,
- .qc_fill_rtf = ahci_qc_fill_rtf,
-
- .freeze = ahci_freeze,
- .thaw = ahci_thaw,
- .softreset = ahci_softreset,
- .hardreset = ahci_hardreset,
- .postreset = ahci_postreset,
- .pmp_softreset = ahci_softreset,
- .error_handler = ahci_error_handler,
- .post_internal_cmd = ahci_post_internal_cmd,
- .dev_config = ahci_dev_config,
-
- .scr_read = ahci_scr_read,
- .scr_write = ahci_scr_write,
- .pmp_attach = ahci_pmp_attach,
- .pmp_detach = ahci_pmp_detach,
-
- .enable_pm = ahci_enable_alpm,
- .disable_pm = ahci_disable_alpm,
- .em_show = ahci_led_show,
- .em_store = ahci_led_store,
- .sw_activity_show = ahci_activity_show,
- .sw_activity_store = ahci_activity_store,
-#ifdef CONFIG_PM
- .port_suspend = ahci_port_suspend,
- .port_resume = ahci_port_resume,
-#endif
- .port_start = ahci_port_start,
- .port_stop = ahci_port_stop,
-};
static struct ata_port_operations ahci_vt8251_ops = {
.inherits = &ahci_ops,
#endif
};
-static int ahci_em_messages = 1;
-module_param(ahci_em_messages, int, 0444);
-/* add other LED protocol types when they become supported */
-MODULE_PARM_DESC(ahci_em_messages,
- "Set AHCI Enclosure Management Message type (0 = disabled, 1 = LED");
-
-#if defined(CONFIG_PATA_MARVELL) || defined(CONFIG_PATA_MARVELL_MODULE)
-static int marvell_enable;
-#else
-static int marvell_enable = 1;
-#endif
-module_param(marvell_enable, int, 0644);
-MODULE_PARM_DESC(marvell_enable, "Marvell SATA via AHCI (1 = enabled)");
-
-
-static inline int ahci_nr_ports(u32 cap)
-{
- return (cap & 0x1f) + 1;
-}
-
-static inline void __iomem *__ahci_port_base(struct ata_host *host,
- unsigned int port_no)
-{
- struct ahci_host_priv *hpriv = host->private_data;
- void __iomem *mmio = hpriv->mmio;
-
- return mmio + 0x100 + (port_no * 0x80);
-}
-
-static inline void __iomem *ahci_port_base(struct ata_port *ap)
-{
- return __ahci_port_base(ap->host, ap->port_no);
-}
-
-static void ahci_enable_ahci(void __iomem *mmio)
-{
- int i;
- u32 tmp;
-
- /* turn on AHCI_EN */
- tmp = readl(mmio + HOST_CTL);
- if (tmp & HOST_AHCI_EN)
- return;
-
- /* Some controllers need AHCI_EN to be written multiple times.
- * Try a few times before giving up.
- */
- for (i = 0; i < 5; i++) {
- tmp |= HOST_AHCI_EN;
- writel(tmp, mmio + HOST_CTL);
- tmp = readl(mmio + HOST_CTL); /* flush && sanity check */
- if (tmp & HOST_AHCI_EN)
- return;
- msleep(10);
- }
-
- WARN_ON(1);
-}
-
-static ssize_t ahci_show_host_caps(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct Scsi_Host *shost = class_to_shost(dev);
- struct ata_port *ap = ata_shost_to_port(shost);
- struct ahci_host_priv *hpriv = ap->host->private_data;
-
- return sprintf(buf, "%x\n", hpriv->cap);
-}
-
-static ssize_t ahci_show_host_cap2(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct Scsi_Host *shost = class_to_shost(dev);
- struct ata_port *ap = ata_shost_to_port(shost);
- struct ahci_host_priv *hpriv = ap->host->private_data;
-
- return sprintf(buf, "%x\n", hpriv->cap2);
-}
-
-static ssize_t ahci_show_host_version(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct Scsi_Host *shost = class_to_shost(dev);
- struct ata_port *ap = ata_shost_to_port(shost);
- struct ahci_host_priv *hpriv = ap->host->private_data;
- void __iomem *mmio = hpriv->mmio;
-
- return sprintf(buf, "%x\n", readl(mmio + HOST_VERSION));
-}
-
-static ssize_t ahci_show_port_cmd(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct Scsi_Host *shost = class_to_shost(dev);
- struct ata_port *ap = ata_shost_to_port(shost);
- void __iomem *port_mmio = ahci_port_base(ap);
-
- return sprintf(buf, "%x\n", readl(port_mmio + PORT_CMD));
-}
-
-/**
- * ahci_save_initial_config - Save and fixup initial config values
- * @dev: target AHCI device
- * @hpriv: host private area to store config values
- * @force_port_map: force port map to a specified value
- * @mask_port_map: mask out particular bits from port map
- *
- * Some registers containing configuration info might be setup by
- * BIOS and might be cleared on reset. This function saves the
- * initial values of those registers into @hpriv such that they
- * can be restored after controller reset.
- *
- * If inconsistent, config values are fixed up by this function.
- *
- * LOCKING:
- * None.
- */
-static void ahci_save_initial_config(struct device *dev,
- struct ahci_host_priv *hpriv,
- unsigned int force_port_map,
- unsigned int mask_port_map)
-{
- void __iomem *mmio = hpriv->mmio;
- u32 cap, cap2, vers, port_map;
- int i;
-
- /* make sure AHCI mode is enabled before accessing CAP */
- ahci_enable_ahci(mmio);
-
- /* Values prefixed with saved_ are written back to host after
- * reset. Values without are used for driver operation.
- */
- hpriv->saved_cap = cap = readl(mmio + HOST_CAP);
- hpriv->saved_port_map = port_map = readl(mmio + HOST_PORTS_IMPL);
-
- /* CAP2 register is only defined for AHCI 1.2 and later */
- vers = readl(mmio + HOST_VERSION);
- if ((vers >> 16) > 1 ||
- ((vers >> 16) == 1 && (vers & 0xFFFF) >= 0x200))
- hpriv->saved_cap2 = cap2 = readl(mmio + HOST_CAP2);
- else
- hpriv->saved_cap2 = cap2 = 0;
-
- /* some chips have errata preventing 64bit use */
- if ((cap & HOST_CAP_64) && (hpriv->flags & AHCI_HFLAG_32BIT_ONLY)) {
- dev_printk(KERN_INFO, dev,
- "controller can't do 64bit DMA, forcing 32bit\n");
- cap &= ~HOST_CAP_64;
- }
-
- if ((cap & HOST_CAP_NCQ) && (hpriv->flags & AHCI_HFLAG_NO_NCQ)) {
- dev_printk(KERN_INFO, dev,
- "controller can't do NCQ, turning off CAP_NCQ\n");
- cap &= ~HOST_CAP_NCQ;
- }
-
- if (!(cap & HOST_CAP_NCQ) && (hpriv->flags & AHCI_HFLAG_YES_NCQ)) {
- dev_printk(KERN_INFO, dev,
- "controller can do NCQ, turning on CAP_NCQ\n");
- cap |= HOST_CAP_NCQ;
- }
-
- if ((cap & HOST_CAP_PMP) && (hpriv->flags & AHCI_HFLAG_NO_PMP)) {
- dev_printk(KERN_INFO, dev,
- "controller can't do PMP, turning off CAP_PMP\n");
- cap &= ~HOST_CAP_PMP;
- }
-
- if ((cap & HOST_CAP_SNTF) && (hpriv->flags & AHCI_HFLAG_NO_SNTF)) {
- dev_printk(KERN_INFO, dev,
- "controller can't do SNTF, turning off CAP_SNTF\n");
- cap &= ~HOST_CAP_SNTF;
- }
-
- if (force_port_map && port_map != force_port_map) {
- dev_printk(KERN_INFO, dev, "forcing port_map 0x%x -> 0x%x\n",
- port_map, force_port_map);
- port_map = force_port_map;
- }
-
- if (mask_port_map) {
- dev_printk(KERN_ERR, dev, "masking port_map 0x%x -> 0x%x\n",
- port_map,
- port_map & mask_port_map);
- port_map &= mask_port_map;
- }
-
- /* cross check port_map and cap.n_ports */
- if (port_map) {
- int map_ports = 0;
-
- for (i = 0; i < AHCI_MAX_PORTS; i++)
- if (port_map & (1 << i))
- map_ports++;
-
- /* If PI has more ports than n_ports, whine, clear
- * port_map and let it be generated from n_ports.
- */
- if (map_ports > ahci_nr_ports(cap)) {
- dev_printk(KERN_WARNING, dev,
- "implemented port map (0x%x) contains more "
- "ports than nr_ports (%u), using nr_ports\n",
- port_map, ahci_nr_ports(cap));
- port_map = 0;
- }
- }
-
- /* fabricate port_map from cap.nr_ports */
- if (!port_map) {
- port_map = (1 << ahci_nr_ports(cap)) - 1;
- dev_printk(KERN_WARNING, dev,
- "forcing PORTS_IMPL to 0x%x\n", port_map);
-
- /* write the fixed up value to the PI register */
- hpriv->saved_port_map = port_map;
- }
-
- /* record values to use during operation */
- hpriv->cap = cap;
- hpriv->cap2 = cap2;
- hpriv->port_map = port_map;
-}
-
-static void ahci_pci_save_initial_config(struct pci_dev *pdev,
- struct ahci_host_priv *hpriv)
-{
- unsigned int force_port_map = 0;
- unsigned int mask_port_map = 0;
-
- if (pdev->vendor == PCI_VENDOR_ID_JMICRON && pdev->device == 0x2361) {
- dev_info(&pdev->dev, "JMB361 has only one port\n");
- force_port_map = 1;
- }
-
- /*
- * Temporary Marvell 6145 hack: PATA port presence
- * is asserted through the standard AHCI port
- * presence register, as bit 4 (counting from 0)
- */
- if (hpriv->flags & AHCI_HFLAG_MV_PATA) {
- if (pdev->device == 0x6121)
- mask_port_map = 0x3;
- else
- mask_port_map = 0xf;
- dev_info(&pdev->dev,
- "Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.\n");
- }
-
- ahci_save_initial_config(&pdev->dev, hpriv, force_port_map,
- mask_port_map);
-}
-
-/**
- * ahci_restore_initial_config - Restore initial config
- * @host: target ATA host
- *
- * Restore initial config stored by ahci_save_initial_config().
- *
- * LOCKING:
- * None.
- */
-static void ahci_restore_initial_config(struct ata_host *host)
-{
- struct ahci_host_priv *hpriv = host->private_data;
- void __iomem *mmio = hpriv->mmio;
-
- writel(hpriv->saved_cap, mmio + HOST_CAP);
- if (hpriv->saved_cap2)
- writel(hpriv->saved_cap2, mmio + HOST_CAP2);
- writel(hpriv->saved_port_map, mmio + HOST_PORTS_IMPL);
- (void) readl(mmio + HOST_PORTS_IMPL); /* flush */
-}
-
-static unsigned ahci_scr_offset(struct ata_port *ap, unsigned int sc_reg)
-{
- static const int offset[] = {
- [SCR_STATUS] = PORT_SCR_STAT,
- [SCR_CONTROL] = PORT_SCR_CTL,
- [SCR_ERROR] = PORT_SCR_ERR,
- [SCR_ACTIVE] = PORT_SCR_ACT,
- [SCR_NOTIFICATION] = PORT_SCR_NTF,
- };
- struct ahci_host_priv *hpriv = ap->host->private_data;
-
- if (sc_reg < ARRAY_SIZE(offset) &&
- (sc_reg != SCR_NOTIFICATION || (hpriv->cap & HOST_CAP_SNTF)))
- return offset[sc_reg];
- return 0;
-}
-
-static int ahci_scr_read(struct ata_link *link, unsigned int sc_reg, u32 *val)
-{
- void __iomem *port_mmio = ahci_port_base(link->ap);
- int offset = ahci_scr_offset(link->ap, sc_reg);
-
- if (offset) {
- *val = readl(port_mmio + offset);
- return 0;
- }
- return -EINVAL;
-}
-
-static int ahci_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val)
-{
- void __iomem *port_mmio = ahci_port_base(link->ap);
- int offset = ahci_scr_offset(link->ap, sc_reg);
-
- if (offset) {
- writel(val, port_mmio + offset);
- return 0;
- }
- return -EINVAL;
-}
-
-static void ahci_start_engine(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 tmp;
-
- /* start DMA */
- tmp = readl(port_mmio + PORT_CMD);
- tmp |= PORT_CMD_START;
- writel(tmp, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
-}
-
-static int ahci_stop_engine(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 tmp;
-
- tmp = readl(port_mmio + PORT_CMD);
-
- /* check if the HBA is idle */
- if ((tmp & (PORT_CMD_START | PORT_CMD_LIST_ON)) == 0)
- return 0;
-
- /* setting HBA to idle */
- tmp &= ~PORT_CMD_START;
- writel(tmp, port_mmio + PORT_CMD);
-
- /* wait for engine to stop. This could be as long as 500 msec */
- tmp = ata_wait_register(port_mmio + PORT_CMD,
- PORT_CMD_LIST_ON, PORT_CMD_LIST_ON, 1, 500);
- if (tmp & PORT_CMD_LIST_ON)
- return -EIO;
-
- return 0;
-}
-
-static void ahci_start_fis_rx(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
- struct ahci_host_priv *hpriv = ap->host->private_data;
- struct ahci_port_priv *pp = ap->private_data;
- u32 tmp;
-
- /* set FIS registers */
- if (hpriv->cap & HOST_CAP_64)
- writel((pp->cmd_slot_dma >> 16) >> 16,
- port_mmio + PORT_LST_ADDR_HI);
- writel(pp->cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
-
- if (hpriv->cap & HOST_CAP_64)
- writel((pp->rx_fis_dma >> 16) >> 16,
- port_mmio + PORT_FIS_ADDR_HI);
- writel(pp->rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
-
- /* enable FIS reception */
- tmp = readl(port_mmio + PORT_CMD);
- tmp |= PORT_CMD_FIS_RX;
- writel(tmp, port_mmio + PORT_CMD);
-
- /* flush */
- readl(port_mmio + PORT_CMD);
-}
-
-static int ahci_stop_fis_rx(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 tmp;
-
- /* disable FIS reception */
- tmp = readl(port_mmio + PORT_CMD);
- tmp &= ~PORT_CMD_FIS_RX;
- writel(tmp, port_mmio + PORT_CMD);
-
- /* wait for completion, spec says 500ms, give it 1000 */
- tmp = ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_FIS_ON,
- PORT_CMD_FIS_ON, 10, 1000);
- if (tmp & PORT_CMD_FIS_ON)
- return -EBUSY;
-
- return 0;
-}
-
-static void ahci_power_up(struct ata_port *ap)
-{
- struct ahci_host_priv *hpriv = ap->host->private_data;
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 cmd;
-
- cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
-
- /* spin up device */
- if (hpriv->cap & HOST_CAP_SSS) {
- cmd |= PORT_CMD_SPIN_UP;
- writel(cmd, port_mmio + PORT_CMD);
- }
-
- /* wake up link */
- writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD);
-}
-
-static void ahci_disable_alpm(struct ata_port *ap)
-{
- struct ahci_host_priv *hpriv = ap->host->private_data;
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 cmd;
- struct ahci_port_priv *pp = ap->private_data;
-
- /* IPM bits should be disabled by libata-core */
- /* get the existing command bits */
- cmd = readl(port_mmio + PORT_CMD);
-
- /* disable ALPM and ASP */
- cmd &= ~PORT_CMD_ASP;
- cmd &= ~PORT_CMD_ALPE;
-
- /* force the interface back to active */
- cmd |= PORT_CMD_ICC_ACTIVE;
-
- /* write out new cmd value */
- writel(cmd, port_mmio + PORT_CMD);
- cmd = readl(port_mmio + PORT_CMD);
-
- /* wait 10ms to be sure we've come out of any low power state */
- msleep(10);
-
- /* clear out any PhyRdy stuff from interrupt status */
- writel(PORT_IRQ_PHYRDY, port_mmio + PORT_IRQ_STAT);
-
- /* go ahead and clean out PhyRdy Change from Serror too */
- ahci_scr_write(&ap->link, SCR_ERROR, ((1 << 16) | (1 << 18)));
-
- /*
- * Clear flag to indicate that we should ignore all PhyRdy
- * state changes
- */
- hpriv->flags &= ~AHCI_HFLAG_NO_HOTPLUG;
-
- /*
- * Enable interrupts on Phy Ready.
- */
- pp->intr_mask |= PORT_IRQ_PHYRDY;
- writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
-
- /*
- * don't change the link pm policy - we can be called
- * just to turn of link pm temporarily
- */
-}
-
-static int ahci_enable_alpm(struct ata_port *ap,
- enum link_pm policy)
-{
- struct ahci_host_priv *hpriv = ap->host->private_data;
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 cmd;
- struct ahci_port_priv *pp = ap->private_data;
- u32 asp;
-
- /* Make sure the host is capable of link power management */
- if (!(hpriv->cap & HOST_CAP_ALPM))
- return -EINVAL;
-
- switch (policy) {
- case MAX_PERFORMANCE:
- case NOT_AVAILABLE:
- /*
- * if we came here with NOT_AVAILABLE,
- * it just means this is the first time we
- * have tried to enable - default to max performance,
- * and let the user go to lower power modes on request.
- */
- ahci_disable_alpm(ap);
- return 0;
- case MIN_POWER:
- /* configure HBA to enter SLUMBER */
- asp = PORT_CMD_ASP;
- break;
- case MEDIUM_POWER:
- /* configure HBA to enter PARTIAL */
- asp = 0;
- break;
- default:
- return -EINVAL;
- }
-
- /*
- * Disable interrupts on Phy Ready. This keeps us from
- * getting woken up due to spurious phy ready interrupts
- * TBD - Hot plug should be done via polling now, is
- * that even supported?
- */
- pp->intr_mask &= ~PORT_IRQ_PHYRDY;
- writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
-
- /*
- * Set a flag to indicate that we should ignore all PhyRdy
- * state changes since these can happen now whenever we
- * change link state
- */
- hpriv->flags |= AHCI_HFLAG_NO_HOTPLUG;
-
- /* get the existing command bits */
- cmd = readl(port_mmio + PORT_CMD);
-
- /*
- * Set ASP based on Policy
- */
- cmd |= asp;
-
- /*
- * Setting this bit will instruct the HBA to aggressively
- * enter a lower power link state when it's appropriate and
- * based on the value set above for ASP
- */
- cmd |= PORT_CMD_ALPE;
-
- /* write out new cmd value */
- writel(cmd, port_mmio + PORT_CMD);
- cmd = readl(port_mmio + PORT_CMD);
-
- /* IPM bits should be set by libata-core */
- return 0;
-}
-
-#ifdef CONFIG_PM
-static void ahci_power_down(struct ata_port *ap)
-{
- struct ahci_host_priv *hpriv = ap->host->private_data;
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 cmd, scontrol;
-
- if (!(hpriv->cap & HOST_CAP_SSS))
- return;
-
- /* put device into listen mode, first set PxSCTL.DET to 0 */
- scontrol = readl(port_mmio + PORT_SCR_CTL);
- scontrol &= ~0xf;
- writel(scontrol, port_mmio + PORT_SCR_CTL);
-
- /* then set PxCMD.SUD to 0 */
- cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
- cmd &= ~PORT_CMD_SPIN_UP;
- writel(cmd, port_mmio + PORT_CMD);
-}
-#endif
-
-static void ahci_start_port(struct ata_port *ap)
-{
- struct ahci_port_priv *pp = ap->private_data;
- struct ata_link *link;
- struct ahci_em_priv *emp;
- ssize_t rc;
- int i;
-
- /* enable FIS reception */
- ahci_start_fis_rx(ap);
-
- /* enable DMA */
- ahci_start_engine(ap);
-
- /* turn on LEDs */
- if (ap->flags & ATA_FLAG_EM) {
- ata_for_each_link(link, ap, EDGE) {
- emp = &pp->em_priv[link->pmp];
-
- /* EM Transmit bit maybe busy during init */
- for (i = 0; i < EM_MAX_RETRY; i++) {
- rc = ahci_transmit_led_message(ap,
- emp->led_state,
- 4);
- if (rc == -EBUSY)
- msleep(1);
- else
- break;
- }
- }
- }
-
- if (ap->flags & ATA_FLAG_SW_ACTIVITY)
- ata_for_each_link(link, ap, EDGE)
- ahci_init_sw_activity(link);
-
-}
-
-static int ahci_deinit_port(struct ata_port *ap, const char **emsg)
-{
- int rc;
-
- /* disable DMA */
- rc = ahci_stop_engine(ap);
- if (rc) {
- *emsg = "failed to stop engine";
- return rc;
- }
-
- /* disable FIS reception */
- rc = ahci_stop_fis_rx(ap);
- if (rc) {
- *emsg = "failed stop FIS RX";
- return rc;
- }
-
- return 0;
-}
-
-static int ahci_reset_controller(struct ata_host *host)
-{
- struct ahci_host_priv *hpriv = host->private_data;
- void __iomem *mmio = hpriv->mmio;
- u32 tmp;
-
- /* we must be in AHCI mode, before using anything
- * AHCI-specific, such as HOST_RESET.
- */
- ahci_enable_ahci(mmio);
-
- /* global controller reset */
- if (!ahci_skip_host_reset) {
- tmp = readl(mmio + HOST_CTL);
- if ((tmp & HOST_RESET) == 0) {
- writel(tmp | HOST_RESET, mmio + HOST_CTL);
- readl(mmio + HOST_CTL); /* flush */
- }
-
- /*
- * to perform host reset, OS should set HOST_RESET
- * and poll until this bit is read to be "0".
- * reset must complete within 1 second, or
- * the hardware should be considered fried.
- */
- tmp = ata_wait_register(mmio + HOST_CTL, HOST_RESET,
- HOST_RESET, 10, 1000);
-
- if (tmp & HOST_RESET) {
- dev_printk(KERN_ERR, host->dev,
- "controller reset failed (0x%x)\n", tmp);
- return -EIO;
- }
-
- /* turn on AHCI mode */
- ahci_enable_ahci(mmio);
-
- /* Some registers might be cleared on reset. Restore
- * initial values.
- */
- ahci_restore_initial_config(host);
- } else
- dev_printk(KERN_INFO, host->dev,
- "skipping global host reset\n");
-
- return 0;
-}
-
-static int ahci_pci_reset_controller(struct ata_host *host)
-{
- struct pci_dev *pdev = to_pci_dev(host->dev);
-
- ahci_reset_controller(host);
-
- if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
- struct ahci_host_priv *hpriv = host->private_data;
- u16 tmp16;
-
- /* configure PCS */
- pci_read_config_word(pdev, 0x92, &tmp16);
- if ((tmp16 & hpriv->port_map) != hpriv->port_map) {
- tmp16 |= hpriv->port_map;
- pci_write_config_word(pdev, 0x92, tmp16);
- }
- }
-
- return 0;
-}
-
-static void ahci_sw_activity(struct ata_link *link)
-{
- struct ata_port *ap = link->ap;
- struct ahci_port_priv *pp = ap->private_data;
- struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
-
- if (!(link->flags & ATA_LFLAG_SW_ACTIVITY))
- return;
-
- emp->activity++;
- if (!timer_pending(&emp->timer))
- mod_timer(&emp->timer, jiffies + msecs_to_jiffies(10));
-}
-
-static void ahci_sw_activity_blink(unsigned long arg)
-{
- struct ata_link *link = (struct ata_link *)arg;
- struct ata_port *ap = link->ap;
- struct ahci_port_priv *pp = ap->private_data;
- struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
- unsigned long led_message = emp->led_state;
- u32 activity_led_state;
- unsigned long flags;
-
- led_message &= EM_MSG_LED_VALUE;
- led_message |= ap->port_no | (link->pmp << 8);
-
- /* check to see if we've had activity. If so,
- * toggle state of LED and reset timer. If not,
- * turn LED to desired idle state.
- */
- spin_lock_irqsave(ap->lock, flags);
- if (emp->saved_activity != emp->activity) {
- emp->saved_activity = emp->activity;
- /* get the current LED state */
- activity_led_state = led_message & EM_MSG_LED_VALUE_ON;
-
- if (activity_led_state)
- activity_led_state = 0;
- else
- activity_led_state = 1;
-
- /* clear old state */
- led_message &= ~EM_MSG_LED_VALUE_ACTIVITY;
-
- /* toggle state */
- led_message |= (activity_led_state << 16);
- mod_timer(&emp->timer, jiffies + msecs_to_jiffies(100));
- } else {
- /* switch to idle */
- led_message &= ~EM_MSG_LED_VALUE_ACTIVITY;
- if (emp->blink_policy == BLINK_OFF)
- led_message |= (1 << 16);
- }
- spin_unlock_irqrestore(ap->lock, flags);
- ahci_transmit_led_message(ap, led_message, 4);
-}
-
-static void ahci_init_sw_activity(struct ata_link *link)
-{
- struct ata_port *ap = link->ap;
- struct ahci_port_priv *pp = ap->private_data;
- struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
-
- /* init activity stats, setup timer */
- emp->saved_activity = emp->activity = 0;
- setup_timer(&emp->timer, ahci_sw_activity_blink, (unsigned long)link);
-
- /* check our blink policy and set flag for link if it's enabled */
- if (emp->blink_policy)
- link->flags |= ATA_LFLAG_SW_ACTIVITY;
-}
-
-static int ahci_reset_em(struct ata_host *host)
-{
- struct ahci_host_priv *hpriv = host->private_data;
- void __iomem *mmio = hpriv->mmio;
- u32 em_ctl;
-
- em_ctl = readl(mmio + HOST_EM_CTL);
- if ((em_ctl & EM_CTL_TM) || (em_ctl & EM_CTL_RST))
- return -EINVAL;
-
- writel(em_ctl | EM_CTL_RST, mmio + HOST_EM_CTL);
- return 0;
-}
-
-static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
- ssize_t size)
-{
- struct ahci_host_priv *hpriv = ap->host->private_data;
- struct ahci_port_priv *pp = ap->private_data;
- void __iomem *mmio = hpriv->mmio;
- u32 em_ctl;
- u32 message[] = {0, 0};
- unsigned long flags;
- int pmp;
- struct ahci_em_priv *emp;
-
- /* get the slot number from the message */
- pmp = (state & EM_MSG_LED_PMP_SLOT) >> 8;
- if (pmp < EM_MAX_SLOTS)
- emp = &pp->em_priv[pmp];
- else
- return -EINVAL;
-
- spin_lock_irqsave(ap->lock, flags);
-
- /*
- * if we are still busy transmitting a previous message,
- * do not allow
- */
- em_ctl = readl(mmio + HOST_EM_CTL);
- if (em_ctl & EM_CTL_TM) {
- spin_unlock_irqrestore(ap->lock, flags);
- return -EBUSY;
- }
-
- /*
- * create message header - this is all zero except for
- * the message size, which is 4 bytes.
- */
- message[0] |= (4 << 8);
-
- /* ignore 0:4 of byte zero, fill in port info yourself */
- message[1] = ((state & ~EM_MSG_LED_HBA_PORT) | ap->port_no);
-
- /* write message to EM_LOC */
- writel(message[0], mmio + hpriv->em_loc);
- writel(message[1], mmio + hpriv->em_loc+4);
-
- /* save off new led state for port/slot */
- emp->led_state = state;
-
- /*
- * tell hardware to transmit the message
- */
- writel(em_ctl | EM_CTL_TM, mmio + HOST_EM_CTL);
-
- spin_unlock_irqrestore(ap->lock, flags);
- return size;
-}
-
-static ssize_t ahci_led_show(struct ata_port *ap, char *buf)
-{
- struct ahci_port_priv *pp = ap->private_data;
- struct ata_link *link;
- struct ahci_em_priv *emp;
- int rc = 0;
-
- ata_for_each_link(link, ap, EDGE) {
- emp = &pp->em_priv[link->pmp];
- rc += sprintf(buf, "%lx\n", emp->led_state);
- }
- return rc;
-}
-
-static ssize_t ahci_led_store(struct ata_port *ap, const char *buf,
- size_t size)
-{
- int state;
- int pmp;
- struct ahci_port_priv *pp = ap->private_data;
- struct ahci_em_priv *emp;
-
- state = simple_strtoul(buf, NULL, 0);
-
- /* get the slot number from the message */
- pmp = (state & EM_MSG_LED_PMP_SLOT) >> 8;
- if (pmp < EM_MAX_SLOTS)
- emp = &pp->em_priv[pmp];
- else
- return -EINVAL;
-
- /* mask off the activity bits if we are in sw_activity
- * mode, user should turn off sw_activity before setting
- * activity led through em_message
- */
- if (emp->blink_policy)
- state &= ~EM_MSG_LED_VALUE_ACTIVITY;
-
- return ahci_transmit_led_message(ap, state, size);
-}
-
-static ssize_t ahci_activity_store(struct ata_device *dev, enum sw_activity val)
-{
- struct ata_link *link = dev->link;
- struct ata_port *ap = link->ap;
- struct ahci_port_priv *pp = ap->private_data;
- struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
- u32 port_led_state = emp->led_state;
-
- /* save the desired Activity LED behavior */
- if (val == OFF) {
- /* clear LFLAG */
- link->flags &= ~(ATA_LFLAG_SW_ACTIVITY);
-
- /* set the LED to OFF */
- port_led_state &= EM_MSG_LED_VALUE_OFF;
- port_led_state |= (ap->port_no | (link->pmp << 8));
- ahci_transmit_led_message(ap, port_led_state, 4);
- } else {
- link->flags |= ATA_LFLAG_SW_ACTIVITY;
- if (val == BLINK_OFF) {
- /* set LED to ON for idle */
- port_led_state &= EM_MSG_LED_VALUE_OFF;
- port_led_state |= (ap->port_no | (link->pmp << 8));
- port_led_state |= EM_MSG_LED_VALUE_ON; /* check this */
- ahci_transmit_led_message(ap, port_led_state, 4);
- }
- }
- emp->blink_policy = val;
- return 0;
-}
-
-static ssize_t ahci_activity_show(struct ata_device *dev, char *buf)
-{
- struct ata_link *link = dev->link;
- struct ata_port *ap = link->ap;
- struct ahci_port_priv *pp = ap->private_data;
- struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
-
- /* display the saved value of activity behavior for this
- * disk.
- */
- return sprintf(buf, "%d\n", emp->blink_policy);
-}
-
-static void ahci_port_init(struct device *dev, struct ata_port *ap,
- int port_no, void __iomem *mmio,
- void __iomem *port_mmio)
-{
- const char *emsg = NULL;
- int rc;
- u32 tmp;
-
- /* make sure port is not active */
- rc = ahci_deinit_port(ap, &emsg);
- if (rc)
- dev_warn(dev, "%s (%d)\n", emsg, rc);
-
- /* clear SError */
- tmp = readl(port_mmio + PORT_SCR_ERR);
- VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
- writel(tmp, port_mmio + PORT_SCR_ERR);
-
- /* clear port IRQ */
- tmp = readl(port_mmio + PORT_IRQ_STAT);
- VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
- if (tmp)
- writel(tmp, port_mmio + PORT_IRQ_STAT);
-
- writel(1 << port_no, mmio + HOST_IRQ_STAT);
-}
-
-static void ahci_init_controller(struct ata_host *host)
-{
- struct ahci_host_priv *hpriv = host->private_data;
- void __iomem *mmio = hpriv->mmio;
- int i;
- void __iomem *port_mmio;
- u32 tmp;
-
- for (i = 0; i < host->n_ports; i++) {
- struct ata_port *ap = host->ports[i];
-
- port_mmio = ahci_port_base(ap);
- if (ata_port_is_dummy(ap))
- continue;
-
- ahci_port_init(host->dev, ap, i, mmio, port_mmio);
- }
-
- tmp = readl(mmio + HOST_CTL);
- VPRINTK("HOST_CTL 0x%x\n", tmp);
- writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL);
- tmp = readl(mmio + HOST_CTL);
- VPRINTK("HOST_CTL 0x%x\n", tmp);
-}
-
-static void ahci_pci_init_controller(struct ata_host *host)
-{
- struct ahci_host_priv *hpriv = host->private_data;
- struct pci_dev *pdev = to_pci_dev(host->dev);
- void __iomem *port_mmio;
- u32 tmp;
- int mv;
-
- if (hpriv->flags & AHCI_HFLAG_MV_PATA) {
- if (pdev->device == 0x6121)
- mv = 2;
- else
- mv = 4;
- port_mmio = __ahci_port_base(host, mv);
-
- writel(0, port_mmio + PORT_IRQ_MASK);
-
- /* clear port IRQ */
- tmp = readl(port_mmio + PORT_IRQ_STAT);
- VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
- if (tmp)
- writel(tmp, port_mmio + PORT_IRQ_STAT);
- }
-
- ahci_init_controller(host);
-}
-
-static void ahci_dev_config(struct ata_device *dev)
-{
- struct ahci_host_priv *hpriv = dev->link->ap->host->private_data;
-
- if (hpriv->flags & AHCI_HFLAG_SECT255) {
- dev->max_sectors = 255;
- ata_dev_printk(dev, KERN_INFO,
- "SB600 AHCI: limiting to 255 sectors per cmd\n");
- }
-}
-
-static unsigned int ahci_dev_classify(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
- struct ata_taskfile tf;
- u32 tmp;
-
- tmp = readl(port_mmio + PORT_SIG);
- tf.lbah = (tmp >> 24) & 0xff;
- tf.lbam = (tmp >> 16) & 0xff;
- tf.lbal = (tmp >> 8) & 0xff;
- tf.nsect = (tmp) & 0xff;
-
- return ata_dev_classify(&tf);
-}
-
-static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
- u32 opts)
-{
- dma_addr_t cmd_tbl_dma;
-
- cmd_tbl_dma = pp->cmd_tbl_dma + tag * AHCI_CMD_TBL_SZ;
-
- pp->cmd_slot[tag].opts = cpu_to_le32(opts);
- pp->cmd_slot[tag].status = 0;
- pp->cmd_slot[tag].tbl_addr = cpu_to_le32(cmd_tbl_dma & 0xffffffff);
- pp->cmd_slot[tag].tbl_addr_hi = cpu_to_le32((cmd_tbl_dma >> 16) >> 16);
-}
-
-static int ahci_kick_engine(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
- struct ahci_host_priv *hpriv = ap->host->private_data;
- u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
- u32 tmp;
- int busy, rc;
-
- /* stop engine */
- rc = ahci_stop_engine(ap);
- if (rc)
- goto out_restart;
-
- /* need to do CLO?
- * always do CLO if PMP is attached (AHCI-1.3 9.2)
- */
- busy = status & (ATA_BUSY | ATA_DRQ);
- if (!busy && !sata_pmp_attached(ap)) {
- rc = 0;
- goto out_restart;
- }
-
- if (!(hpriv->cap & HOST_CAP_CLO)) {
- rc = -EOPNOTSUPP;
- goto out_restart;
- }
-
- /* perform CLO */
- tmp = readl(port_mmio + PORT_CMD);
- tmp |= PORT_CMD_CLO;
- writel(tmp, port_mmio + PORT_CMD);
-
- rc = 0;
- tmp = ata_wait_register(port_mmio + PORT_CMD,
- PORT_CMD_CLO, PORT_CMD_CLO, 1, 500);
- if (tmp & PORT_CMD_CLO)
- rc = -EIO;
-
- /* restart engine */
- out_restart:
- ahci_start_engine(ap);
- return rc;
-}
-
-static int ahci_exec_polled_cmd(struct ata_port *ap, int pmp,
- struct ata_taskfile *tf, int is_cmd, u16 flags,
- unsigned long timeout_msec)
-{
- const u32 cmd_fis_len = 5; /* five dwords */
- struct ahci_port_priv *pp = ap->private_data;
- void __iomem *port_mmio = ahci_port_base(ap);
- u8 *fis = pp->cmd_tbl;
- u32 tmp;
-
- /* prep the command */
- ata_tf_to_fis(tf, pmp, is_cmd, fis);
- ahci_fill_cmd_slot(pp, 0, cmd_fis_len | flags | (pmp << 12));
-
- /* issue & wait */
- writel(1, port_mmio + PORT_CMD_ISSUE);
-
- if (timeout_msec) {
- tmp = ata_wait_register(port_mmio + PORT_CMD_ISSUE, 0x1, 0x1,
- 1, timeout_msec);
- if (tmp & 0x1) {
- ahci_kick_engine(ap);
- return -EBUSY;
- }
- } else
- readl(port_mmio + PORT_CMD_ISSUE); /* flush */
-
- return 0;
-}
-
-static int ahci_do_softreset(struct ata_link *link, unsigned int *class,
- int pmp, unsigned long deadline,
- int (*check_ready)(struct ata_link *link))
-{
- struct ata_port *ap = link->ap;
- struct ahci_host_priv *hpriv = ap->host->private_data;
- const char *reason = NULL;
- unsigned long now, msecs;
- struct ata_taskfile tf;
- int rc;
-
- DPRINTK("ENTER\n");
-
- /* prepare for SRST (AHCI-1.1 10.4.1) */
- rc = ahci_kick_engine(ap);
- if (rc && rc != -EOPNOTSUPP)
- ata_link_printk(link, KERN_WARNING,
- "failed to reset engine (errno=%d)\n", rc);
-
- ata_tf_init(link->device, &tf);
-
- /* issue the first D2H Register FIS */
- msecs = 0;
- now = jiffies;
- if (time_after(now, deadline))
- msecs = jiffies_to_msecs(deadline - now);
-
- tf.ctl |= ATA_SRST;
- if (ahci_exec_polled_cmd(ap, pmp, &tf, 0,
- AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY, msecs)) {
- rc = -EIO;
- reason = "1st FIS failed";
- goto fail;
- }
-
- /* spec says at least 5us, but be generous and sleep for 1ms */
- msleep(1);
-
- /* issue the second D2H Register FIS */
- tf.ctl &= ~ATA_SRST;
- ahci_exec_polled_cmd(ap, pmp, &tf, 0, 0, 0);
-
- /* wait for link to become ready */
- rc = ata_wait_after_reset(link, deadline, check_ready);
- if (rc == -EBUSY && hpriv->flags & AHCI_HFLAG_SRST_TOUT_IS_OFFLINE) {
- /*
- * Workaround for cases where link online status can't
- * be trusted. Treat device readiness timeout as link
- * offline.
- */
- ata_link_printk(link, KERN_INFO,
- "device not ready, treating as offline\n");
- *class = ATA_DEV_NONE;
- } else if (rc) {
- /* link occupied, -ENODEV too is an error */
- reason = "device not ready";
- goto fail;
- } else
- *class = ahci_dev_classify(ap);
-
- DPRINTK("EXIT, class=%u\n", *class);
- return 0;
-
- fail:
- ata_link_printk(link, KERN_ERR, "softreset failed (%s)\n", reason);
- return rc;
-}
-
-static int ahci_check_ready(struct ata_link *link)
-{
- void __iomem *port_mmio = ahci_port_base(link->ap);
- u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
-
- return ata_check_ready(status);
-}
-
-static int ahci_softreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline)
-{
- int pmp = sata_srst_pmp(link);
-
- DPRINTK("ENTER\n");
-
- return ahci_do_softreset(link, class, pmp, deadline, ahci_check_ready);
-}
-
-static int ahci_sb600_check_ready(struct ata_link *link)
-{
- void __iomem *port_mmio = ahci_port_base(link->ap);
- u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
- u32 irq_status = readl(port_mmio + PORT_IRQ_STAT);
-
- /*
- * There is no need to check TFDATA if BAD PMP is found due to HW bug,
- * which can save timeout delay.
- */
- if (irq_status & PORT_IRQ_BAD_PMP)
- return -EIO;
-
- return ata_check_ready(status);
-}
-
-static int ahci_sb600_softreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline)
-{
- struct ata_port *ap = link->ap;
- void __iomem *port_mmio = ahci_port_base(ap);
- int pmp = sata_srst_pmp(link);
- int rc;
- u32 irq_sts;
-
- DPRINTK("ENTER\n");
-
- rc = ahci_do_softreset(link, class, pmp, deadline,
- ahci_sb600_check_ready);
-
- /*
- * Soft reset fails on some ATI chips with IPMS set when PMP
- * is enabled but SATA HDD/ODD is connected to SATA port,
- * do soft reset again to port 0.
- */
- if (rc == -EIO) {
- irq_sts = readl(port_mmio + PORT_IRQ_STAT);
- if (irq_sts & PORT_IRQ_BAD_PMP) {
- ata_link_printk(link, KERN_WARNING,
- "applying SB600 PMP SRST workaround "
- "and retrying\n");
- rc = ahci_do_softreset(link, class, 0, deadline,
- ahci_check_ready);
- }
- }
-
- return rc;
-}
-
-static int ahci_hardreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline)
-{
- const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
- struct ata_port *ap = link->ap;
- struct ahci_port_priv *pp = ap->private_data;
- u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
- struct ata_taskfile tf;
- bool online;
- int rc;
-
- DPRINTK("ENTER\n");
-
- ahci_stop_engine(ap);
-
- /* clear D2H reception area to properly wait for D2H FIS */
- ata_tf_init(link->device, &tf);
- tf.command = 0x80;
- ata_tf_to_fis(&tf, 0, 0, d2h_fis);
-
- rc = sata_link_hardreset(link, timing, deadline, &online,
- ahci_check_ready);
-
- ahci_start_engine(ap);
-
- if (online)
- *class = ahci_dev_classify(ap);
-
- DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
- return rc;
-}
-
-static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline)
-{
- struct ata_port *ap = link->ap;
- bool online;
- int rc;
-
- DPRINTK("ENTER\n");
-
- ahci_stop_engine(ap);
-
- rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
- deadline, &online, NULL);
-
- ahci_start_engine(ap);
-
- DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
-
- /* vt8251 doesn't clear BSY on signature FIS reception,
- * request follow-up softreset.
- */
- return online ? -EAGAIN : rc;
-}
-
-static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline)
-{
- struct ata_port *ap = link->ap;
- struct ahci_port_priv *pp = ap->private_data;
- u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
- struct ata_taskfile tf;
- bool online;
- int rc;
-
- ahci_stop_engine(ap);
-
- /* clear D2H reception area to properly wait for D2H FIS */
- ata_tf_init(link->device, &tf);
- tf.command = 0x80;
- ata_tf_to_fis(&tf, 0, 0, d2h_fis);
-
- rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
- deadline, &online, NULL);
-
- ahci_start_engine(ap);
-
- /* The pseudo configuration device on SIMG4726 attached to
- * ASUS P5W-DH Deluxe doesn't send signature FIS after
- * hardreset if no device is attached to the first downstream
- * port && the pseudo device locks up on SRST w/ PMP==0. To
- * work around this, wait for !BSY only briefly. If BSY isn't
- * cleared, perform CLO and proceed to IDENTIFY (achieved by
- * ATA_LFLAG_NO_SRST and ATA_LFLAG_ASSUME_ATA).
- *
- * Wait for two seconds. Devices attached to downstream port
- * which can't process the following IDENTIFY after this will
- * have to be reset again. For most cases, this should
- * suffice while making probing snappish enough.
- */
- if (online) {
- rc = ata_wait_after_reset(link, jiffies + 2 * HZ,
- ahci_check_ready);
- if (rc)
- ahci_kick_engine(ap);
- }
- return rc;
-}
-
-static void ahci_postreset(struct ata_link *link, unsigned int *class)
-{
- struct ata_port *ap = link->ap;
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 new_tmp, tmp;
-
- ata_std_postreset(link, class);
-
- /* Make sure port's ATAPI bit is set appropriately */
- new_tmp = tmp = readl(port_mmio + PORT_CMD);
- if (*class == ATA_DEV_ATAPI)
- new_tmp |= PORT_CMD_ATAPI;
- else
- new_tmp &= ~PORT_CMD_ATAPI;
- if (new_tmp != tmp) {
- writel(new_tmp, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
- }
-}
-
-static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl)
-{
- struct scatterlist *sg;
- struct ahci_sg *ahci_sg = cmd_tbl + AHCI_CMD_TBL_HDR_SZ;
- unsigned int si;
-
- VPRINTK("ENTER\n");
-
- /*
- * Next, the S/G list.
- */
- for_each_sg(qc->sg, sg, qc->n_elem, si) {
- dma_addr_t addr = sg_dma_address(sg);
- u32 sg_len = sg_dma_len(sg);
-
- ahci_sg[si].addr = cpu_to_le32(addr & 0xffffffff);
- ahci_sg[si].addr_hi = cpu_to_le32((addr >> 16) >> 16);
- ahci_sg[si].flags_size = cpu_to_le32(sg_len - 1);
- }
-
- return si;
-}
-
-static int ahci_pmp_qc_defer(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- struct ahci_port_priv *pp = ap->private_data;
-
- if (!sata_pmp_attached(ap) || pp->fbs_enabled)
- return ata_std_qc_defer(qc);
- else
- return sata_pmp_qc_defer_cmd_switch(qc);
-}
-
-static void ahci_qc_prep(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- struct ahci_port_priv *pp = ap->private_data;
- int is_atapi = ata_is_atapi(qc->tf.protocol);
- void *cmd_tbl;
- u32 opts;
- const u32 cmd_fis_len = 5; /* five dwords */
- unsigned int n_elem;
-
- /*
- * Fill in command table information. First, the header,
- * a SATA Register - Host to Device command FIS.
- */
- cmd_tbl = pp->cmd_tbl + qc->tag * AHCI_CMD_TBL_SZ;
-
- ata_tf_to_fis(&qc->tf, qc->dev->link->pmp, 1, cmd_tbl);
- if (is_atapi) {
- memset(cmd_tbl + AHCI_CMD_TBL_CDB, 0, 32);
- memcpy(cmd_tbl + AHCI_CMD_TBL_CDB, qc->cdb, qc->dev->cdb_len);
- }
-
- n_elem = 0;
- if (qc->flags & ATA_QCFLAG_DMAMAP)
- n_elem = ahci_fill_sg(qc, cmd_tbl);
-
- /*
- * Fill in command slot information.
- */
- opts = cmd_fis_len | n_elem << 16 | (qc->dev->link->pmp << 12);
- if (qc->tf.flags & ATA_TFLAG_WRITE)
- opts |= AHCI_CMD_WRITE;
- if (is_atapi)
- opts |= AHCI_CMD_ATAPI | AHCI_CMD_PREFETCH;
-
- ahci_fill_cmd_slot(pp, qc->tag, opts);
-}
-
-static void ahci_fbs_dec_intr(struct ata_port *ap)
-{
- struct ahci_port_priv *pp = ap->private_data;
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 fbs = readl(port_mmio + PORT_FBS);
- int retries = 3;
-
- DPRINTK("ENTER\n");
- BUG_ON(!pp->fbs_enabled);
-
- /* time to wait for DEC is not specified by AHCI spec,
- * add a retry loop for safety.
- */
- writel(fbs | PORT_FBS_DEC, port_mmio + PORT_FBS);
- fbs = readl(port_mmio + PORT_FBS);
- while ((fbs & PORT_FBS_DEC) && retries--) {
- udelay(1);
- fbs = readl(port_mmio + PORT_FBS);
- }
-
- if (fbs & PORT_FBS_DEC)
- dev_printk(KERN_ERR, ap->host->dev,
- "failed to clear device error\n");
-}
-
-static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
-{
- struct ahci_host_priv *hpriv = ap->host->private_data;
- struct ahci_port_priv *pp = ap->private_data;
- struct ata_eh_info *host_ehi = &ap->link.eh_info;
- struct ata_link *link = NULL;
- struct ata_queued_cmd *active_qc;
- struct ata_eh_info *active_ehi;
- bool fbs_need_dec = false;
- u32 serror;
-
- /* determine active link with error */
- if (pp->fbs_enabled) {
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 fbs = readl(port_mmio + PORT_FBS);
- int pmp = fbs >> PORT_FBS_DWE_OFFSET;
-
- if ((fbs & PORT_FBS_SDE) && (pmp < ap->nr_pmp_links) &&
- ata_link_online(&ap->pmp_link[pmp])) {
- link = &ap->pmp_link[pmp];
- fbs_need_dec = true;
- }
-
- } else
- ata_for_each_link(link, ap, EDGE)
- if (ata_link_active(link))
- break;
-
- if (!link)
- link = &ap->link;
-
- active_qc = ata_qc_from_tag(ap, link->active_tag);
- active_ehi = &link->eh_info;
-
- /* record irq stat */
- ata_ehi_clear_desc(host_ehi);
- ata_ehi_push_desc(host_ehi, "irq_stat 0x%08x", irq_stat);
-
- /* AHCI needs SError cleared; otherwise, it might lock up */
- ahci_scr_read(&ap->link, SCR_ERROR, &serror);
- ahci_scr_write(&ap->link, SCR_ERROR, serror);
- host_ehi->serror |= serror;
-
- /* some controllers set IRQ_IF_ERR on device errors, ignore it */
- if (hpriv->flags & AHCI_HFLAG_IGN_IRQ_IF_ERR)
- irq_stat &= ~PORT_IRQ_IF_ERR;
-
- if (irq_stat & PORT_IRQ_TF_ERR) {
- /* If qc is active, charge it; otherwise, the active
- * link. There's no active qc on NCQ errors. It will
- * be determined by EH by reading log page 10h.
- */
- if (active_qc)
- active_qc->err_mask |= AC_ERR_DEV;
- else
- active_ehi->err_mask |= AC_ERR_DEV;
-
- if (hpriv->flags & AHCI_HFLAG_IGN_SERR_INTERNAL)
- host_ehi->serror &= ~SERR_INTERNAL;
- }
-
- if (irq_stat & PORT_IRQ_UNK_FIS) {
- u32 *unk = (u32 *)(pp->rx_fis + RX_FIS_UNK);
-
- active_ehi->err_mask |= AC_ERR_HSM;
- active_ehi->action |= ATA_EH_RESET;
- ata_ehi_push_desc(active_ehi,
- "unknown FIS %08x %08x %08x %08x" ,
- unk[0], unk[1], unk[2], unk[3]);
- }
-
- if (sata_pmp_attached(ap) && (irq_stat & PORT_IRQ_BAD_PMP)) {
- active_ehi->err_mask |= AC_ERR_HSM;
- active_ehi->action |= ATA_EH_RESET;
- ata_ehi_push_desc(active_ehi, "incorrect PMP");
- }
-
- if (irq_stat & (PORT_IRQ_HBUS_ERR | PORT_IRQ_HBUS_DATA_ERR)) {
- host_ehi->err_mask |= AC_ERR_HOST_BUS;
- host_ehi->action |= ATA_EH_RESET;
- ata_ehi_push_desc(host_ehi, "host bus error");
- }
-
- if (irq_stat & PORT_IRQ_IF_ERR) {
- if (fbs_need_dec)
- active_ehi->err_mask |= AC_ERR_DEV;
- else {
- host_ehi->err_mask |= AC_ERR_ATA_BUS;
- host_ehi->action |= ATA_EH_RESET;
- }
-
- ata_ehi_push_desc(host_ehi, "interface fatal error");
- }
-
- if (irq_stat & (PORT_IRQ_CONNECT | PORT_IRQ_PHYRDY)) {
- ata_ehi_hotplugged(host_ehi);
- ata_ehi_push_desc(host_ehi, "%s",
- irq_stat & PORT_IRQ_CONNECT ?
- "connection status changed" : "PHY RDY changed");
- }
-
- /* okay, let's hand over to EH */
-
- if (irq_stat & PORT_IRQ_FREEZE)
- ata_port_freeze(ap);
- else if (fbs_need_dec) {
- ata_link_abort(link);
- ahci_fbs_dec_intr(ap);
- } else
- ata_port_abort(ap);
-}
-
-static void ahci_port_intr(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
- struct ata_eh_info *ehi = &ap->link.eh_info;
- struct ahci_port_priv *pp = ap->private_data;
- struct ahci_host_priv *hpriv = ap->host->private_data;
- int resetting = !!(ap->pflags & ATA_PFLAG_RESETTING);
- u32 status, qc_active = 0;
- int rc;
-
- status = readl(port_mmio + PORT_IRQ_STAT);
- writel(status, port_mmio + PORT_IRQ_STAT);
-
- /* ignore BAD_PMP while resetting */
- if (unlikely(resetting))
- status &= ~PORT_IRQ_BAD_PMP;
-
- /* If we are getting PhyRdy, this is
- * just a power state change, we should
- * clear out this, plus the PhyRdy/Comm
- * Wake bits from Serror
- */
- if ((hpriv->flags & AHCI_HFLAG_NO_HOTPLUG) &&
- (status & PORT_IRQ_PHYRDY)) {
- status &= ~PORT_IRQ_PHYRDY;
- ahci_scr_write(&ap->link, SCR_ERROR, ((1 << 16) | (1 << 18)));
- }
-
- if (unlikely(status & PORT_IRQ_ERROR)) {
- ahci_error_intr(ap, status);
- return;
- }
-
- if (status & PORT_IRQ_SDB_FIS) {
- /* If SNotification is available, leave notification
- * handling to sata_async_notification(). If not,
- * emulate it by snooping SDB FIS RX area.
- *
- * Snooping FIS RX area is probably cheaper than
- * poking SNotification but some constrollers which
- * implement SNotification, ICH9 for example, don't
- * store AN SDB FIS into receive area.
- */
- if (hpriv->cap & HOST_CAP_SNTF)
- sata_async_notification(ap);
- else {
- /* If the 'N' bit in word 0 of the FIS is set,
- * we just received asynchronous notification.
- * Tell libata about it.
- *
- * Lack of SNotification should not appear in
- * ahci 1.2, so the workaround is unnecessary
- * when FBS is enabled.
- */
- if (pp->fbs_enabled)
- WARN_ON_ONCE(1);
- else {
- const __le32 *f = pp->rx_fis + RX_FIS_SDB;
- u32 f0 = le32_to_cpu(f[0]);
- if (f0 & (1 << 15))
- sata_async_notification(ap);
- }
- }
- }
-
- /* pp->active_link is not reliable once FBS is enabled, both
- * PORT_SCR_ACT and PORT_CMD_ISSUE should be checked because
- * NCQ and non-NCQ commands may be in flight at the same time.
- */
- if (pp->fbs_enabled) {
- if (ap->qc_active) {
- qc_active = readl(port_mmio + PORT_SCR_ACT);
- qc_active |= readl(port_mmio + PORT_CMD_ISSUE);
- }
- } else {
- /* pp->active_link is valid iff any command is in flight */
- if (ap->qc_active && pp->active_link->sactive)
- qc_active = readl(port_mmio + PORT_SCR_ACT);
- else
- qc_active = readl(port_mmio + PORT_CMD_ISSUE);
- }
-
- rc = ata_qc_complete_multiple(ap, qc_active);
-
- /* while resetting, invalid completions are expected */
- if (unlikely(rc < 0 && !resetting)) {
- ehi->err_mask |= AC_ERR_HSM;
- ehi->action |= ATA_EH_RESET;
- ata_port_freeze(ap);
- }
-}
-
-static irqreturn_t ahci_interrupt(int irq, void *dev_instance)
-{
- struct ata_host *host = dev_instance;
- struct ahci_host_priv *hpriv;
- unsigned int i, handled = 0;
- void __iomem *mmio;
- u32 irq_stat, irq_masked;
-
- VPRINTK("ENTER\n");
-
- hpriv = host->private_data;
- mmio = hpriv->mmio;
-
- /* sigh. 0xffffffff is a valid return from h/w */
- irq_stat = readl(mmio + HOST_IRQ_STAT);
- if (!irq_stat)
- return IRQ_NONE;
-
- irq_masked = irq_stat & hpriv->port_map;
+#if defined(CONFIG_PATA_MARVELL) || defined(CONFIG_PATA_MARVELL_MODULE)
+static int marvell_enable;
+#else
+static int marvell_enable = 1;
+#endif
+module_param(marvell_enable, int, 0644);
+MODULE_PARM_DESC(marvell_enable, "Marvell SATA via AHCI (1 = enabled)");
- spin_lock(&host->lock);
- for (i = 0; i < host->n_ports; i++) {
- struct ata_port *ap;
-
- if (!(irq_masked & (1 << i)))
- continue;
-
- ap = host->ports[i];
- if (ap) {
- ahci_port_intr(ap);
- VPRINTK("port %u\n", i);
- } else {
- VPRINTK("port %u (no irq)\n", i);
- if (ata_ratelimit())
- dev_printk(KERN_WARNING, host->dev,
- "interrupt on disabled port %u\n", i);
- }
+static void ahci_pci_save_initial_config(struct pci_dev *pdev,
+ struct ahci_host_priv *hpriv)
+{
+ unsigned int force_port_map = 0;
+ unsigned int mask_port_map = 0;
- handled = 1;
+ if (pdev->vendor == PCI_VENDOR_ID_JMICRON && pdev->device == 0x2361) {
+ dev_info(&pdev->dev, "JMB361 has only one port\n");
+ force_port_map = 1;
}
- /* HOST_IRQ_STAT behaves as level triggered latch meaning that
- * it should be cleared after all the port events are cleared;
- * otherwise, it will raise a spurious interrupt after each
- * valid one. Please read section 10.6.2 of ahci 1.1 for more
- * information.
- *
- * Also, use the unmasked value to clear interrupt as spurious
- * pending event on a dummy port might cause screaming IRQ.
+ /*
+ * Temporary Marvell 6145 hack: PATA port presence
+ * is asserted through the standard AHCI port
+ * presence register, as bit 4 (counting from 0)
*/
- writel(irq_stat, mmio + HOST_IRQ_STAT);
-
- spin_unlock(&host->lock);
-
- VPRINTK("EXIT\n");
+ if (hpriv->flags & AHCI_HFLAG_MV_PATA) {
+ if (pdev->device == 0x6121)
+ mask_port_map = 0x3;
+ else
+ mask_port_map = 0xf;
+ dev_info(&pdev->dev,
+ "Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.\n");
+ }
- return IRQ_RETVAL(handled);
+ ahci_save_initial_config(&pdev->dev, hpriv, force_port_map,
+ mask_port_map);
}
-static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc)
+static int ahci_pci_reset_controller(struct ata_host *host)
{
- struct ata_port *ap = qc->ap;
- void __iomem *port_mmio = ahci_port_base(ap);
- struct ahci_port_priv *pp = ap->private_data;
+ struct pci_dev *pdev = to_pci_dev(host->dev);
- /* Keep track of the currently active link. It will be used
- * in completion path to determine whether NCQ phase is in
- * progress.
- */
- pp->active_link = qc->dev->link;
+ ahci_reset_controller(host);
- if (qc->tf.protocol == ATA_PROT_NCQ)
- writel(1 << qc->tag, port_mmio + PORT_SCR_ACT);
+ if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
+ struct ahci_host_priv *hpriv = host->private_data;
+ u16 tmp16;
- if (pp->fbs_enabled && pp->fbs_last_dev != qc->dev->link->pmp) {
- u32 fbs = readl(port_mmio + PORT_FBS);
- fbs &= ~(PORT_FBS_DEV_MASK | PORT_FBS_DEC);
- fbs |= qc->dev->link->pmp << PORT_FBS_DEV_OFFSET;
- writel(fbs, port_mmio + PORT_FBS);
- pp->fbs_last_dev = qc->dev->link->pmp;
+ /* configure PCS */
+ pci_read_config_word(pdev, 0x92, &tmp16);
+ if ((tmp16 & hpriv->port_map) != hpriv->port_map) {
+ tmp16 |= hpriv->port_map;
+ pci_write_config_word(pdev, 0x92, tmp16);
+ }
}
- writel(1 << qc->tag, port_mmio + PORT_CMD_ISSUE);
-
- ahci_sw_activity(qc->dev->link);
-
return 0;
}
-static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc)
-{
- struct ahci_port_priv *pp = qc->ap->private_data;
- u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
-
- if (pp->fbs_enabled)
- d2h_fis += qc->dev->link->pmp * AHCI_RX_FIS_SZ;
-
- ata_tf_from_fis(d2h_fis, &qc->result_tf);
- return true;
-}
-
-static void ahci_freeze(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
-
- /* turn IRQ off */
- writel(0, port_mmio + PORT_IRQ_MASK);
-}
-
-static void ahci_thaw(struct ata_port *ap)
+static void ahci_pci_init_controller(struct ata_host *host)
{
- struct ahci_host_priv *hpriv = ap->host->private_data;
- void __iomem *mmio = hpriv->mmio;
- void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_host_priv *hpriv = host->private_data;
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+ void __iomem *port_mmio;
u32 tmp;
- struct ahci_port_priv *pp = ap->private_data;
+ int mv;
- /* clear IRQ */
- tmp = readl(port_mmio + PORT_IRQ_STAT);
- writel(tmp, port_mmio + PORT_IRQ_STAT);
- writel(1 << ap->port_no, mmio + HOST_IRQ_STAT);
+ if (hpriv->flags & AHCI_HFLAG_MV_PATA) {
+ if (pdev->device == 0x6121)
+ mv = 2;
+ else
+ mv = 4;
+ port_mmio = __ahci_port_base(host, mv);
- /* turn IRQ back on */
- writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
-}
+ writel(0, port_mmio + PORT_IRQ_MASK);
-static void ahci_error_handler(struct ata_port *ap)
-{
- if (!(ap->pflags & ATA_PFLAG_FROZEN)) {
- /* restart engine */
- ahci_stop_engine(ap);
- ahci_start_engine(ap);
+ /* clear port IRQ */
+ tmp = readl(port_mmio + PORT_IRQ_STAT);
+ VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
+ if (tmp)
+ writel(tmp, port_mmio + PORT_IRQ_STAT);
}
- sata_pmp_error_handler(ap);
+ ahci_init_controller(host);
}
-static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
+static int ahci_sb600_check_ready(struct ata_link *link)
{
- struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = ahci_port_base(link->ap);
+ u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
+ u32 irq_status = readl(port_mmio + PORT_IRQ_STAT);
+
+ /*
+ * There is no need to check TFDATA if BAD PMP is found due to HW bug,
+ * which can save timeout delay.
+ */
+ if (irq_status & PORT_IRQ_BAD_PMP)
+ return -EIO;
- /* make DMA engine forget about the failed command */
- if (qc->flags & ATA_QCFLAG_FAILED)
- ahci_kick_engine(ap);
+ return ata_check_ready(status);
}
-static void ahci_enable_fbs(struct ata_port *ap)
+static int ahci_sb600_softreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
{
- struct ahci_port_priv *pp = ap->private_data;
+ struct ata_port *ap = link->ap;
void __iomem *port_mmio = ahci_port_base(ap);
- u32 fbs;
+ int pmp = sata_srst_pmp(link);
int rc;
+ u32 irq_sts;
- if (!pp->fbs_supported)
- return;
-
- fbs = readl(port_mmio + PORT_FBS);
- if (fbs & PORT_FBS_EN) {
- pp->fbs_enabled = true;
- pp->fbs_last_dev = -1; /* initialization */
- return;
- }
+ DPRINTK("ENTER\n");
- rc = ahci_stop_engine(ap);
- if (rc)
- return;
+ rc = ahci_do_softreset(link, class, pmp, deadline,
+ ahci_sb600_check_ready);
- writel(fbs | PORT_FBS_EN, port_mmio + PORT_FBS);
- fbs = readl(port_mmio + PORT_FBS);
- if (fbs & PORT_FBS_EN) {
- dev_printk(KERN_INFO, ap->host->dev, "FBS is enabled.\n");
- pp->fbs_enabled = true;
- pp->fbs_last_dev = -1; /* initialization */
- } else
- dev_printk(KERN_ERR, ap->host->dev, "Failed to enable FBS\n");
+ /*
+ * Soft reset fails on some ATI chips with IPMS set when PMP
+ * is enabled but SATA HDD/ODD is connected to SATA port,
+ * do soft reset again to port 0.
+ */
+ if (rc == -EIO) {
+ irq_sts = readl(port_mmio + PORT_IRQ_STAT);
+ if (irq_sts & PORT_IRQ_BAD_PMP) {
+ ata_link_printk(link, KERN_WARNING,
+ "applying SB600 PMP SRST workaround "
+ "and retrying\n");
+ rc = ahci_do_softreset(link, class, 0, deadline,
+ ahci_check_ready);
+ }
+ }
- ahci_start_engine(ap);
+ return rc;
}
-static void ahci_disable_fbs(struct ata_port *ap)
+static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
{
- struct ahci_port_priv *pp = ap->private_data;
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 fbs;
+ struct ata_port *ap = link->ap;
+ bool online;
int rc;
- if (!pp->fbs_supported)
- return;
-
- fbs = readl(port_mmio + PORT_FBS);
- if ((fbs & PORT_FBS_EN) == 0) {
- pp->fbs_enabled = false;
- return;
- }
+ DPRINTK("ENTER\n");
- rc = ahci_stop_engine(ap);
- if (rc)
- return;
+ ahci_stop_engine(ap);
- writel(fbs & ~PORT_FBS_EN, port_mmio + PORT_FBS);
- fbs = readl(port_mmio + PORT_FBS);
- if (fbs & PORT_FBS_EN)
- dev_printk(KERN_ERR, ap->host->dev, "Failed to disable FBS\n");
- else {
- dev_printk(KERN_INFO, ap->host->dev, "FBS is disabled.\n");
- pp->fbs_enabled = false;
- }
+ rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
+ deadline, &online, NULL);
ahci_start_engine(ap);
-}
-
-static void ahci_pmp_attach(struct ata_port *ap)
-{
- void __iomem *port_mmio = ahci_port_base(ap);
- struct ahci_port_priv *pp = ap->private_data;
- u32 cmd;
-
- cmd = readl(port_mmio + PORT_CMD);
- cmd |= PORT_CMD_PMP;
- writel(cmd, port_mmio + PORT_CMD);
- ahci_enable_fbs(ap);
+ DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
- pp->intr_mask |= PORT_IRQ_BAD_PMP;
- writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+ /* vt8251 doesn't clear BSY on signature FIS reception,
+ * request follow-up softreset.
+ */
+ return online ? -EAGAIN : rc;
}
-static void ahci_pmp_detach(struct ata_port *ap)
+static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
{
- void __iomem *port_mmio = ahci_port_base(ap);
+ struct ata_port *ap = link->ap;
struct ahci_port_priv *pp = ap->private_data;
- u32 cmd;
-
- ahci_disable_fbs(ap);
-
- cmd = readl(port_mmio + PORT_CMD);
- cmd &= ~PORT_CMD_PMP;
- writel(cmd, port_mmio + PORT_CMD);
-
- pp->intr_mask &= ~PORT_IRQ_BAD_PMP;
- writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
-}
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+ struct ata_taskfile tf;
+ bool online;
+ int rc;
-static int ahci_port_resume(struct ata_port *ap)
-{
- ahci_power_up(ap);
- ahci_start_port(ap);
+ ahci_stop_engine(ap);
- if (sata_pmp_attached(ap))
- ahci_pmp_attach(ap);
- else
- ahci_pmp_detach(ap);
+ /* clear D2H reception area to properly wait for D2H FIS */
+ ata_tf_init(link->device, &tf);
+ tf.command = 0x80;
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
- return 0;
-}
+ rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
+ deadline, &online, NULL);
-#ifdef CONFIG_PM
-static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
-{
- const char *emsg = NULL;
- int rc;
+ ahci_start_engine(ap);
- rc = ahci_deinit_port(ap, &emsg);
- if (rc == 0)
- ahci_power_down(ap);
- else {
- ata_port_printk(ap, KERN_ERR, "%s (%d)\n", emsg, rc);
- ahci_start_port(ap);
+ /* The pseudo configuration device on SIMG4726 attached to
+ * ASUS P5W-DH Deluxe doesn't send signature FIS after
+ * hardreset if no device is attached to the first downstream
+ * port && the pseudo device locks up on SRST w/ PMP==0. To
+ * work around this, wait for !BSY only briefly. If BSY isn't
+ * cleared, perform CLO and proceed to IDENTIFY (achieved by
+ * ATA_LFLAG_NO_SRST and ATA_LFLAG_ASSUME_ATA).
+ *
+ * Wait for two seconds. Devices attached to downstream port
+ * which can't process the following IDENTIFY after this will
+ * have to be reset again. For most cases, this should
+ * suffice while making probing snappish enough.
+ */
+ if (online) {
+ rc = ata_wait_after_reset(link, jiffies + 2 * HZ,
+ ahci_check_ready);
+ if (rc)
+ ahci_kick_engine(ap);
}
-
return rc;
}
+#ifdef CONFIG_PM
static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
}
#endif
-static int ahci_port_start(struct ata_port *ap)
-{
- struct ahci_host_priv *hpriv = ap->host->private_data;
- struct device *dev = ap->host->dev;
- struct ahci_port_priv *pp;
- void *mem;
- dma_addr_t mem_dma;
- size_t dma_sz, rx_fis_sz;
-
- pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
- if (!pp)
- return -ENOMEM;
-
- /* check FBS capability */
- if ((hpriv->cap & HOST_CAP_FBS) && sata_pmp_supported(ap)) {
- void __iomem *port_mmio = ahci_port_base(ap);
- u32 cmd = readl(port_mmio + PORT_CMD);
- if (cmd & PORT_CMD_FBSCP)
- pp->fbs_supported = true;
- else
- dev_printk(KERN_WARNING, dev,
- "The port is not capable of FBS\n");
- }
-
- if (pp->fbs_supported) {
- dma_sz = AHCI_PORT_PRIV_FBS_DMA_SZ;
- rx_fis_sz = AHCI_RX_FIS_SZ * 16;
- } else {
- dma_sz = AHCI_PORT_PRIV_DMA_SZ;
- rx_fis_sz = AHCI_RX_FIS_SZ;
- }
-
- mem = dmam_alloc_coherent(dev, dma_sz, &mem_dma, GFP_KERNEL);
- if (!mem)
- return -ENOMEM;
- memset(mem, 0, dma_sz);
-
- /*
- * First item in chunk of DMA memory: 32-slot command table,
- * 32 bytes each in size
- */
- pp->cmd_slot = mem;
- pp->cmd_slot_dma = mem_dma;
-
- mem += AHCI_CMD_SLOT_SZ;
- mem_dma += AHCI_CMD_SLOT_SZ;
-
- /*
- * Second item: Received-FIS area
- */
- pp->rx_fis = mem;
- pp->rx_fis_dma = mem_dma;
-
- mem += rx_fis_sz;
- mem_dma += rx_fis_sz;
-
- /*
- * Third item: data area for storing a single command
- * and its scatter-gather table
- */
- pp->cmd_tbl = mem;
- pp->cmd_tbl_dma = mem_dma;
-
- /*
- * Save off initial list of interrupts to be enabled.
- * This could be changed later
- */
- pp->intr_mask = DEF_PORT_IRQ;
-
- ap->private_data = pp;
-
- /* engage engines, captain */
- return ahci_port_resume(ap);
-}
-
-static void ahci_port_stop(struct ata_port *ap)
-{
- const char *emsg = NULL;
- int rc;
-
- /* de-initialize port */
- rc = ahci_deinit_port(ap, &emsg);
- if (rc)
- ata_port_printk(ap, KERN_WARNING, "%s (%d)\n", emsg, rc);
-}
-
static int ahci_configure_dma_masks(struct pci_dev *pdev, int using_dac)
{
int rc;
return 0;
}
-static void ahci_print_info(struct ata_host *host, const char *scc_s)
-{
- struct ahci_host_priv *hpriv = host->private_data;
- void __iomem *mmio = hpriv->mmio;
- u32 vers, cap, cap2, impl, speed;
- const char *speed_s;
-
- vers = readl(mmio + HOST_VERSION);
- cap = hpriv->cap;
- cap2 = hpriv->cap2;
- impl = hpriv->port_map;
-
- speed = (cap >> 20) & 0xf;
- if (speed == 1)
- speed_s = "1.5";
- else if (speed == 2)
- speed_s = "3";
- else if (speed == 3)
- speed_s = "6";
- else
- speed_s = "?";
-
- dev_info(host->dev,
- "AHCI %02x%02x.%02x%02x "
- "%u slots %u ports %s Gbps 0x%x impl %s mode\n"
- ,
-
- (vers >> 24) & 0xff,
- (vers >> 16) & 0xff,
- (vers >> 8) & 0xff,
- vers & 0xff,
-
- ((cap >> 8) & 0x1f) + 1,
- (cap & 0x1f) + 1,
- speed_s,
- impl,
- scc_s);
-
- dev_info(host->dev,
- "flags: "
- "%s%s%s%s%s%s%s"
- "%s%s%s%s%s%s%s"
- "%s%s%s%s%s%s\n"
- ,
-
- cap & HOST_CAP_64 ? "64bit " : "",
- cap & HOST_CAP_NCQ ? "ncq " : "",
- cap & HOST_CAP_SNTF ? "sntf " : "",
- cap & HOST_CAP_MPS ? "ilck " : "",
- cap & HOST_CAP_SSS ? "stag " : "",
- cap & HOST_CAP_ALPM ? "pm " : "",
- cap & HOST_CAP_LED ? "led " : "",
- cap & HOST_CAP_CLO ? "clo " : "",
- cap & HOST_CAP_ONLY ? "only " : "",
- cap & HOST_CAP_PMP ? "pmp " : "",
- cap & HOST_CAP_FBS ? "fbs " : "",
- cap & HOST_CAP_PIO_MULTI ? "pio " : "",
- cap & HOST_CAP_SSC ? "slum " : "",
- cap & HOST_CAP_PART ? "part " : "",
- cap & HOST_CAP_CCC ? "ccc " : "",
- cap & HOST_CAP_EMS ? "ems " : "",
- cap & HOST_CAP_SXS ? "sxs " : "",
- cap2 & HOST_CAP2_APST ? "apst " : "",
- cap2 & HOST_CAP2_NVMHCI ? "nvmp " : "",
- cap2 & HOST_CAP2_BOH ? "boh " : ""
- );
-}
-
static void ahci_pci_print_info(struct ata_host *host)
{
struct pci_dev *pdev = to_pci_dev(host->dev);
{}
#endif
-static void ahci_set_em_messages(struct ahci_host_priv *hpriv,
- struct ata_port_info *pi)
-{
- u8 messages;
- void __iomem *mmio = hpriv->mmio;
- u32 em_loc = readl(mmio + HOST_EM_LOC);
- u32 em_ctl = readl(mmio + HOST_EM_CTL);
-
- if (!ahci_em_messages || !(hpriv->cap & HOST_CAP_EMS))
- return;
-
- messages = (em_ctl & EM_CTRL_MSG_TYPE) >> 16;
-
- /* we only support LED message type right now */
- if ((messages & 0x01) && (ahci_em_messages == 1)) {
- /* store em_loc */
- hpriv->em_loc = ((em_loc >> 16) * 4);
- pi->flags |= ATA_FLAG_EM;
- if (!(em_ctl & EM_CTL_ALHD))
- pi->flags |= ATA_FLAG_SW_ACTIVITY;
- }
-}
-
static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
--- /dev/null
+/*
+ * libahci.c - Common AHCI SATA low-level routines
+ *
+ * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Please ALWAYS copy linux-ide@vger.kernel.org
+ * on emails.
+ *
+ * Copyright 2004-2005 Red Hat, Inc.
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ * libata documentation is available via 'make {ps|pdf}docs',
+ * as Documentation/DocBook/libata.*
+ *
+ * AHCI hardware documentation:
+ * http://www.intel.com/technology/serialata/pdf/rev1_0.pdf
+ * http://www.intel.com/technology/serialata/pdf/rev1_1.pdf
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_cmnd.h>
+#include <linux/libata.h>
+#include "ahci.h"
+
+static int ahci_skip_host_reset;
+int ahci_ignore_sss;
+EXPORT_SYMBOL_GPL(ahci_ignore_sss);
+
+module_param_named(skip_host_reset, ahci_skip_host_reset, int, 0444);
+MODULE_PARM_DESC(skip_host_reset, "skip global host reset (0=don't skip, 1=skip)");
+
+module_param_named(ignore_sss, ahci_ignore_sss, int, 0444);
+MODULE_PARM_DESC(ignore_sss, "Ignore staggered spinup flag (0=don't ignore, 1=ignore)");
+
+static int ahci_enable_alpm(struct ata_port *ap,
+ enum link_pm policy);
+static void ahci_disable_alpm(struct ata_port *ap);
+static ssize_t ahci_led_show(struct ata_port *ap, char *buf);
+static ssize_t ahci_led_store(struct ata_port *ap, const char *buf,
+ size_t size);
+static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
+ ssize_t size);
+
+
+
+static int ahci_scr_read(struct ata_link *link, unsigned int sc_reg, u32 *val);
+static int ahci_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val);
+static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc);
+static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc);
+static int ahci_port_start(struct ata_port *ap);
+static void ahci_port_stop(struct ata_port *ap);
+static void ahci_qc_prep(struct ata_queued_cmd *qc);
+static int ahci_pmp_qc_defer(struct ata_queued_cmd *qc);
+static void ahci_freeze(struct ata_port *ap);
+static void ahci_thaw(struct ata_port *ap);
+static void ahci_enable_fbs(struct ata_port *ap);
+static void ahci_disable_fbs(struct ata_port *ap);
+static void ahci_pmp_attach(struct ata_port *ap);
+static void ahci_pmp_detach(struct ata_port *ap);
+static int ahci_softreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
+static int ahci_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
+static void ahci_postreset(struct ata_link *link, unsigned int *class);
+static void ahci_error_handler(struct ata_port *ap);
+static void ahci_post_internal_cmd(struct ata_queued_cmd *qc);
+static int ahci_port_resume(struct ata_port *ap);
+static void ahci_dev_config(struct ata_device *dev);
+static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
+ u32 opts);
+#ifdef CONFIG_PM
+static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg);
+#endif
+static ssize_t ahci_activity_show(struct ata_device *dev, char *buf);
+static ssize_t ahci_activity_store(struct ata_device *dev,
+ enum sw_activity val);
+static void ahci_init_sw_activity(struct ata_link *link);
+
+static ssize_t ahci_show_host_caps(struct device *dev,
+ struct device_attribute *attr, char *buf);
+static ssize_t ahci_show_host_cap2(struct device *dev,
+ struct device_attribute *attr, char *buf);
+static ssize_t ahci_show_host_version(struct device *dev,
+ struct device_attribute *attr, char *buf);
+static ssize_t ahci_show_port_cmd(struct device *dev,
+ struct device_attribute *attr, char *buf);
+
+static DEVICE_ATTR(ahci_host_caps, S_IRUGO, ahci_show_host_caps, NULL);
+static DEVICE_ATTR(ahci_host_cap2, S_IRUGO, ahci_show_host_cap2, NULL);
+static DEVICE_ATTR(ahci_host_version, S_IRUGO, ahci_show_host_version, NULL);
+static DEVICE_ATTR(ahci_port_cmd, S_IRUGO, ahci_show_port_cmd, NULL);
+
+static struct device_attribute *ahci_shost_attrs[] = {
+ &dev_attr_link_power_management_policy,
+ &dev_attr_em_message_type,
+ &dev_attr_em_message,
+ &dev_attr_ahci_host_caps,
+ &dev_attr_ahci_host_cap2,
+ &dev_attr_ahci_host_version,
+ &dev_attr_ahci_port_cmd,
+ NULL
+};
+
+static struct device_attribute *ahci_sdev_attrs[] = {
+ &dev_attr_sw_activity,
+ &dev_attr_unload_heads,
+ NULL
+};
+
+struct scsi_host_template ahci_sht = {
+ ATA_NCQ_SHT("ahci"),
+ .can_queue = AHCI_MAX_CMDS - 1,
+ .sg_tablesize = AHCI_MAX_SG,
+ .dma_boundary = AHCI_DMA_BOUNDARY,
+ .shost_attrs = ahci_shost_attrs,
+ .sdev_attrs = ahci_sdev_attrs,
+};
+EXPORT_SYMBOL_GPL(ahci_sht);
+
+struct ata_port_operations ahci_ops = {
+ .inherits = &sata_pmp_port_ops,
+
+ .qc_defer = ahci_pmp_qc_defer,
+ .qc_prep = ahci_qc_prep,
+ .qc_issue = ahci_qc_issue,
+ .qc_fill_rtf = ahci_qc_fill_rtf,
+
+ .freeze = ahci_freeze,
+ .thaw = ahci_thaw,
+ .softreset = ahci_softreset,
+ .hardreset = ahci_hardreset,
+ .postreset = ahci_postreset,
+ .pmp_softreset = ahci_softreset,
+ .error_handler = ahci_error_handler,
+ .post_internal_cmd = ahci_post_internal_cmd,
+ .dev_config = ahci_dev_config,
+
+ .scr_read = ahci_scr_read,
+ .scr_write = ahci_scr_write,
+ .pmp_attach = ahci_pmp_attach,
+ .pmp_detach = ahci_pmp_detach,
+
+ .enable_pm = ahci_enable_alpm,
+ .disable_pm = ahci_disable_alpm,
+ .em_show = ahci_led_show,
+ .em_store = ahci_led_store,
+ .sw_activity_show = ahci_activity_show,
+ .sw_activity_store = ahci_activity_store,
+#ifdef CONFIG_PM
+ .port_suspend = ahci_port_suspend,
+ .port_resume = ahci_port_resume,
+#endif
+ .port_start = ahci_port_start,
+ .port_stop = ahci_port_stop,
+};
+EXPORT_SYMBOL_GPL(ahci_ops);
+
+int ahci_em_messages = 1;
+EXPORT_SYMBOL_GPL(ahci_em_messages);
+module_param(ahci_em_messages, int, 0444);
+/* add other LED protocol types when they become supported */
+MODULE_PARM_DESC(ahci_em_messages,
+ "Set AHCI Enclosure Management Message type (0 = disabled, 1 = LED");
+
+static void ahci_enable_ahci(void __iomem *mmio)
+{
+ int i;
+ u32 tmp;
+
+ /* turn on AHCI_EN */
+ tmp = readl(mmio + HOST_CTL);
+ if (tmp & HOST_AHCI_EN)
+ return;
+
+ /* Some controllers need AHCI_EN to be written multiple times.
+ * Try a few times before giving up.
+ */
+ for (i = 0; i < 5; i++) {
+ tmp |= HOST_AHCI_EN;
+ writel(tmp, mmio + HOST_CTL);
+ tmp = readl(mmio + HOST_CTL); /* flush && sanity check */
+ if (tmp & HOST_AHCI_EN)
+ return;
+ msleep(10);
+ }
+
+ WARN_ON(1);
+}
+
+static ssize_t ahci_show_host_caps(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct Scsi_Host *shost = class_to_shost(dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+
+ return sprintf(buf, "%x\n", hpriv->cap);
+}
+
+static ssize_t ahci_show_host_cap2(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct Scsi_Host *shost = class_to_shost(dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+
+ return sprintf(buf, "%x\n", hpriv->cap2);
+}
+
+static ssize_t ahci_show_host_version(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct Scsi_Host *shost = class_to_shost(dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = hpriv->mmio;
+
+ return sprintf(buf, "%x\n", readl(mmio + HOST_VERSION));
+}
+
+static ssize_t ahci_show_port_cmd(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct Scsi_Host *shost = class_to_shost(dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+ void __iomem *port_mmio = ahci_port_base(ap);
+
+ return sprintf(buf, "%x\n", readl(port_mmio + PORT_CMD));
+}
+
+/**
+ * ahci_save_initial_config - Save and fixup initial config values
+ * @dev: target AHCI device
+ * @hpriv: host private area to store config values
+ * @force_port_map: force port map to a specified value
+ * @mask_port_map: mask out particular bits from port map
+ *
+ * Some registers containing configuration info might be setup by
+ * BIOS and might be cleared on reset. This function saves the
+ * initial values of those registers into @hpriv such that they
+ * can be restored after controller reset.
+ *
+ * If inconsistent, config values are fixed up by this function.
+ *
+ * LOCKING:
+ * None.
+ */
+void ahci_save_initial_config(struct device *dev,
+ struct ahci_host_priv *hpriv,
+ unsigned int force_port_map,
+ unsigned int mask_port_map)
+{
+ void __iomem *mmio = hpriv->mmio;
+ u32 cap, cap2, vers, port_map;
+ int i;
+
+ /* make sure AHCI mode is enabled before accessing CAP */
+ ahci_enable_ahci(mmio);
+
+ /* Values prefixed with saved_ are written back to host after
+ * reset. Values without are used for driver operation.
+ */
+ hpriv->saved_cap = cap = readl(mmio + HOST_CAP);
+ hpriv->saved_port_map = port_map = readl(mmio + HOST_PORTS_IMPL);
+
+ /* CAP2 register is only defined for AHCI 1.2 and later */
+ vers = readl(mmio + HOST_VERSION);
+ if ((vers >> 16) > 1 ||
+ ((vers >> 16) == 1 && (vers & 0xFFFF) >= 0x200))
+ hpriv->saved_cap2 = cap2 = readl(mmio + HOST_CAP2);
+ else
+ hpriv->saved_cap2 = cap2 = 0;
+
+ /* some chips have errata preventing 64bit use */
+ if ((cap & HOST_CAP_64) && (hpriv->flags & AHCI_HFLAG_32BIT_ONLY)) {
+ dev_printk(KERN_INFO, dev,
+ "controller can't do 64bit DMA, forcing 32bit\n");
+ cap &= ~HOST_CAP_64;
+ }
+
+ if ((cap & HOST_CAP_NCQ) && (hpriv->flags & AHCI_HFLAG_NO_NCQ)) {
+ dev_printk(KERN_INFO, dev,
+ "controller can't do NCQ, turning off CAP_NCQ\n");
+ cap &= ~HOST_CAP_NCQ;
+ }
+
+ if (!(cap & HOST_CAP_NCQ) && (hpriv->flags & AHCI_HFLAG_YES_NCQ)) {
+ dev_printk(KERN_INFO, dev,
+ "controller can do NCQ, turning on CAP_NCQ\n");
+ cap |= HOST_CAP_NCQ;
+ }
+
+ if ((cap & HOST_CAP_PMP) && (hpriv->flags & AHCI_HFLAG_NO_PMP)) {
+ dev_printk(KERN_INFO, dev,
+ "controller can't do PMP, turning off CAP_PMP\n");
+ cap &= ~HOST_CAP_PMP;
+ }
+
+ if ((cap & HOST_CAP_SNTF) && (hpriv->flags & AHCI_HFLAG_NO_SNTF)) {
+ dev_printk(KERN_INFO, dev,
+ "controller can't do SNTF, turning off CAP_SNTF\n");
+ cap &= ~HOST_CAP_SNTF;
+ }
+
+ if (force_port_map && port_map != force_port_map) {
+ dev_printk(KERN_INFO, dev, "forcing port_map 0x%x -> 0x%x\n",
+ port_map, force_port_map);
+ port_map = force_port_map;
+ }
+
+ if (mask_port_map) {
+ dev_printk(KERN_ERR, dev, "masking port_map 0x%x -> 0x%x\n",
+ port_map,
+ port_map & mask_port_map);
+ port_map &= mask_port_map;
+ }
+
+ /* cross check port_map and cap.n_ports */
+ if (port_map) {
+ int map_ports = 0;
+
+ for (i = 0; i < AHCI_MAX_PORTS; i++)
+ if (port_map & (1 << i))
+ map_ports++;
+
+ /* If PI has more ports than n_ports, whine, clear
+ * port_map and let it be generated from n_ports.
+ */
+ if (map_ports > ahci_nr_ports(cap)) {
+ dev_printk(KERN_WARNING, dev,
+ "implemented port map (0x%x) contains more "
+ "ports than nr_ports (%u), using nr_ports\n",
+ port_map, ahci_nr_ports(cap));
+ port_map = 0;
+ }
+ }
+
+ /* fabricate port_map from cap.nr_ports */
+ if (!port_map) {
+ port_map = (1 << ahci_nr_ports(cap)) - 1;
+ dev_printk(KERN_WARNING, dev,
+ "forcing PORTS_IMPL to 0x%x\n", port_map);
+
+ /* write the fixed up value to the PI register */
+ hpriv->saved_port_map = port_map;
+ }
+
+ /* record values to use during operation */
+ hpriv->cap = cap;
+ hpriv->cap2 = cap2;
+ hpriv->port_map = port_map;
+}
+EXPORT_SYMBOL_GPL(ahci_save_initial_config);
+
+/**
+ * ahci_restore_initial_config - Restore initial config
+ * @host: target ATA host
+ *
+ * Restore initial config stored by ahci_save_initial_config().
+ *
+ * LOCKING:
+ * None.
+ */
+static void ahci_restore_initial_config(struct ata_host *host)
+{
+ struct ahci_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->mmio;
+
+ writel(hpriv->saved_cap, mmio + HOST_CAP);
+ if (hpriv->saved_cap2)
+ writel(hpriv->saved_cap2, mmio + HOST_CAP2);
+ writel(hpriv->saved_port_map, mmio + HOST_PORTS_IMPL);
+ (void) readl(mmio + HOST_PORTS_IMPL); /* flush */
+}
+
+static unsigned ahci_scr_offset(struct ata_port *ap, unsigned int sc_reg)
+{
+ static const int offset[] = {
+ [SCR_STATUS] = PORT_SCR_STAT,
+ [SCR_CONTROL] = PORT_SCR_CTL,
+ [SCR_ERROR] = PORT_SCR_ERR,
+ [SCR_ACTIVE] = PORT_SCR_ACT,
+ [SCR_NOTIFICATION] = PORT_SCR_NTF,
+ };
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+
+ if (sc_reg < ARRAY_SIZE(offset) &&
+ (sc_reg != SCR_NOTIFICATION || (hpriv->cap & HOST_CAP_SNTF)))
+ return offset[sc_reg];
+ return 0;
+}
+
+static int ahci_scr_read(struct ata_link *link, unsigned int sc_reg, u32 *val)
+{
+ void __iomem *port_mmio = ahci_port_base(link->ap);
+ int offset = ahci_scr_offset(link->ap, sc_reg);
+
+ if (offset) {
+ *val = readl(port_mmio + offset);
+ return 0;
+ }
+ return -EINVAL;
+}
+
+static int ahci_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val)
+{
+ void __iomem *port_mmio = ahci_port_base(link->ap);
+ int offset = ahci_scr_offset(link->ap, sc_reg);
+
+ if (offset) {
+ writel(val, port_mmio + offset);
+ return 0;
+ }
+ return -EINVAL;
+}
+
+void ahci_start_engine(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 tmp;
+
+ /* start DMA */
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp |= PORT_CMD_START;
+ writel(tmp, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+}
+EXPORT_SYMBOL_GPL(ahci_start_engine);
+
+int ahci_stop_engine(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 tmp;
+
+ tmp = readl(port_mmio + PORT_CMD);
+
+ /* check if the HBA is idle */
+ if ((tmp & (PORT_CMD_START | PORT_CMD_LIST_ON)) == 0)
+ return 0;
+
+ /* setting HBA to idle */
+ tmp &= ~PORT_CMD_START;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ /* wait for engine to stop. This could be as long as 500 msec */
+ tmp = ata_wait_register(port_mmio + PORT_CMD,
+ PORT_CMD_LIST_ON, PORT_CMD_LIST_ON, 1, 500);
+ if (tmp & PORT_CMD_LIST_ON)
+ return -EIO;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ahci_stop_engine);
+
+static void ahci_start_fis_rx(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ struct ahci_port_priv *pp = ap->private_data;
+ u32 tmp;
+
+ /* set FIS registers */
+ if (hpriv->cap & HOST_CAP_64)
+ writel((pp->cmd_slot_dma >> 16) >> 16,
+ port_mmio + PORT_LST_ADDR_HI);
+ writel(pp->cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
+
+ if (hpriv->cap & HOST_CAP_64)
+ writel((pp->rx_fis_dma >> 16) >> 16,
+ port_mmio + PORT_FIS_ADDR_HI);
+ writel(pp->rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
+
+ /* enable FIS reception */
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp |= PORT_CMD_FIS_RX;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ /* flush */
+ readl(port_mmio + PORT_CMD);
+}
+
+static int ahci_stop_fis_rx(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 tmp;
+
+ /* disable FIS reception */
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp &= ~PORT_CMD_FIS_RX;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ /* wait for completion, spec says 500ms, give it 1000 */
+ tmp = ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_FIS_ON,
+ PORT_CMD_FIS_ON, 10, 1000);
+ if (tmp & PORT_CMD_FIS_ON)
+ return -EBUSY;
+
+ return 0;
+}
+
+static void ahci_power_up(struct ata_port *ap)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 cmd;
+
+ cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
+
+ /* spin up device */
+ if (hpriv->cap & HOST_CAP_SSS) {
+ cmd |= PORT_CMD_SPIN_UP;
+ writel(cmd, port_mmio + PORT_CMD);
+ }
+
+ /* wake up link */
+ writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD);
+}
+
+static void ahci_disable_alpm(struct ata_port *ap)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 cmd;
+ struct ahci_port_priv *pp = ap->private_data;
+
+ /* IPM bits should be disabled by libata-core */
+ /* get the existing command bits */
+ cmd = readl(port_mmio + PORT_CMD);
+
+ /* disable ALPM and ASP */
+ cmd &= ~PORT_CMD_ASP;
+ cmd &= ~PORT_CMD_ALPE;
+
+ /* force the interface back to active */
+ cmd |= PORT_CMD_ICC_ACTIVE;
+
+ /* write out new cmd value */
+ writel(cmd, port_mmio + PORT_CMD);
+ cmd = readl(port_mmio + PORT_CMD);
+
+ /* wait 10ms to be sure we've come out of any low power state */
+ msleep(10);
+
+ /* clear out any PhyRdy stuff from interrupt status */
+ writel(PORT_IRQ_PHYRDY, port_mmio + PORT_IRQ_STAT);
+
+ /* go ahead and clean out PhyRdy Change from Serror too */
+ ahci_scr_write(&ap->link, SCR_ERROR, ((1 << 16) | (1 << 18)));
+
+ /*
+ * Clear flag to indicate that we should ignore all PhyRdy
+ * state changes
+ */
+ hpriv->flags &= ~AHCI_HFLAG_NO_HOTPLUG;
+
+ /*
+ * Enable interrupts on Phy Ready.
+ */
+ pp->intr_mask |= PORT_IRQ_PHYRDY;
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+
+ /*
+ * don't change the link pm policy - we can be called
+ * just to turn of link pm temporarily
+ */
+}
+
+static int ahci_enable_alpm(struct ata_port *ap,
+ enum link_pm policy)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 cmd;
+ struct ahci_port_priv *pp = ap->private_data;
+ u32 asp;
+
+ /* Make sure the host is capable of link power management */
+ if (!(hpriv->cap & HOST_CAP_ALPM))
+ return -EINVAL;
+
+ switch (policy) {
+ case MAX_PERFORMANCE:
+ case NOT_AVAILABLE:
+ /*
+ * if we came here with NOT_AVAILABLE,
+ * it just means this is the first time we
+ * have tried to enable - default to max performance,
+ * and let the user go to lower power modes on request.
+ */
+ ahci_disable_alpm(ap);
+ return 0;
+ case MIN_POWER:
+ /* configure HBA to enter SLUMBER */
+ asp = PORT_CMD_ASP;
+ break;
+ case MEDIUM_POWER:
+ /* configure HBA to enter PARTIAL */
+ asp = 0;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /*
+ * Disable interrupts on Phy Ready. This keeps us from
+ * getting woken up due to spurious phy ready interrupts
+ * TBD - Hot plug should be done via polling now, is
+ * that even supported?
+ */
+ pp->intr_mask &= ~PORT_IRQ_PHYRDY;
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+
+ /*
+ * Set a flag to indicate that we should ignore all PhyRdy
+ * state changes since these can happen now whenever we
+ * change link state
+ */
+ hpriv->flags |= AHCI_HFLAG_NO_HOTPLUG;
+
+ /* get the existing command bits */
+ cmd = readl(port_mmio + PORT_CMD);
+
+ /*
+ * Set ASP based on Policy
+ */
+ cmd |= asp;
+
+ /*
+ * Setting this bit will instruct the HBA to aggressively
+ * enter a lower power link state when it's appropriate and
+ * based on the value set above for ASP
+ */
+ cmd |= PORT_CMD_ALPE;
+
+ /* write out new cmd value */
+ writel(cmd, port_mmio + PORT_CMD);
+ cmd = readl(port_mmio + PORT_CMD);
+
+ /* IPM bits should be set by libata-core */
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static void ahci_power_down(struct ata_port *ap)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 cmd, scontrol;
+
+ if (!(hpriv->cap & HOST_CAP_SSS))
+ return;
+
+ /* put device into listen mode, first set PxSCTL.DET to 0 */
+ scontrol = readl(port_mmio + PORT_SCR_CTL);
+ scontrol &= ~0xf;
+ writel(scontrol, port_mmio + PORT_SCR_CTL);
+
+ /* then set PxCMD.SUD to 0 */
+ cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
+ cmd &= ~PORT_CMD_SPIN_UP;
+ writel(cmd, port_mmio + PORT_CMD);
+}
+#endif
+
+static void ahci_start_port(struct ata_port *ap)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ata_link *link;
+ struct ahci_em_priv *emp;
+ ssize_t rc;
+ int i;
+
+ /* enable FIS reception */
+ ahci_start_fis_rx(ap);
+
+ /* enable DMA */
+ ahci_start_engine(ap);
+
+ /* turn on LEDs */
+ if (ap->flags & ATA_FLAG_EM) {
+ ata_for_each_link(link, ap, EDGE) {
+ emp = &pp->em_priv[link->pmp];
+
+ /* EM Transmit bit maybe busy during init */
+ for (i = 0; i < EM_MAX_RETRY; i++) {
+ rc = ahci_transmit_led_message(ap,
+ emp->led_state,
+ 4);
+ if (rc == -EBUSY)
+ msleep(1);
+ else
+ break;
+ }
+ }
+ }
+
+ if (ap->flags & ATA_FLAG_SW_ACTIVITY)
+ ata_for_each_link(link, ap, EDGE)
+ ahci_init_sw_activity(link);
+
+}
+
+static int ahci_deinit_port(struct ata_port *ap, const char **emsg)
+{
+ int rc;
+
+ /* disable DMA */
+ rc = ahci_stop_engine(ap);
+ if (rc) {
+ *emsg = "failed to stop engine";
+ return rc;
+ }
+
+ /* disable FIS reception */
+ rc = ahci_stop_fis_rx(ap);
+ if (rc) {
+ *emsg = "failed stop FIS RX";
+ return rc;
+ }
+
+ return 0;
+}
+
+int ahci_reset_controller(struct ata_host *host)
+{
+ struct ahci_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->mmio;
+ u32 tmp;
+
+ /* we must be in AHCI mode, before using anything
+ * AHCI-specific, such as HOST_RESET.
+ */
+ ahci_enable_ahci(mmio);
+
+ /* global controller reset */
+ if (!ahci_skip_host_reset) {
+ tmp = readl(mmio + HOST_CTL);
+ if ((tmp & HOST_RESET) == 0) {
+ writel(tmp | HOST_RESET, mmio + HOST_CTL);
+ readl(mmio + HOST_CTL); /* flush */
+ }
+
+ /*
+ * to perform host reset, OS should set HOST_RESET
+ * and poll until this bit is read to be "0".
+ * reset must complete within 1 second, or
+ * the hardware should be considered fried.
+ */
+ tmp = ata_wait_register(mmio + HOST_CTL, HOST_RESET,
+ HOST_RESET, 10, 1000);
+
+ if (tmp & HOST_RESET) {
+ dev_printk(KERN_ERR, host->dev,
+ "controller reset failed (0x%x)\n", tmp);
+ return -EIO;
+ }
+
+ /* turn on AHCI mode */
+ ahci_enable_ahci(mmio);
+
+ /* Some registers might be cleared on reset. Restore
+ * initial values.
+ */
+ ahci_restore_initial_config(host);
+ } else
+ dev_printk(KERN_INFO, host->dev,
+ "skipping global host reset\n");
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ahci_reset_controller);
+
+static void ahci_sw_activity(struct ata_link *link)
+{
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
+
+ if (!(link->flags & ATA_LFLAG_SW_ACTIVITY))
+ return;
+
+ emp->activity++;
+ if (!timer_pending(&emp->timer))
+ mod_timer(&emp->timer, jiffies + msecs_to_jiffies(10));
+}
+
+static void ahci_sw_activity_blink(unsigned long arg)
+{
+ struct ata_link *link = (struct ata_link *)arg;
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
+ unsigned long led_message = emp->led_state;
+ u32 activity_led_state;
+ unsigned long flags;
+
+ led_message &= EM_MSG_LED_VALUE;
+ led_message |= ap->port_no | (link->pmp << 8);
+
+ /* check to see if we've had activity. If so,
+ * toggle state of LED and reset timer. If not,
+ * turn LED to desired idle state.
+ */
+ spin_lock_irqsave(ap->lock, flags);
+ if (emp->saved_activity != emp->activity) {
+ emp->saved_activity = emp->activity;
+ /* get the current LED state */
+ activity_led_state = led_message & EM_MSG_LED_VALUE_ON;
+
+ if (activity_led_state)
+ activity_led_state = 0;
+ else
+ activity_led_state = 1;
+
+ /* clear old state */
+ led_message &= ~EM_MSG_LED_VALUE_ACTIVITY;
+
+ /* toggle state */
+ led_message |= (activity_led_state << 16);
+ mod_timer(&emp->timer, jiffies + msecs_to_jiffies(100));
+ } else {
+ /* switch to idle */
+ led_message &= ~EM_MSG_LED_VALUE_ACTIVITY;
+ if (emp->blink_policy == BLINK_OFF)
+ led_message |= (1 << 16);
+ }
+ spin_unlock_irqrestore(ap->lock, flags);
+ ahci_transmit_led_message(ap, led_message, 4);
+}
+
+static void ahci_init_sw_activity(struct ata_link *link)
+{
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
+
+ /* init activity stats, setup timer */
+ emp->saved_activity = emp->activity = 0;
+ setup_timer(&emp->timer, ahci_sw_activity_blink, (unsigned long)link);
+
+ /* check our blink policy and set flag for link if it's enabled */
+ if (emp->blink_policy)
+ link->flags |= ATA_LFLAG_SW_ACTIVITY;
+}
+
+int ahci_reset_em(struct ata_host *host)
+{
+ struct ahci_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->mmio;
+ u32 em_ctl;
+
+ em_ctl = readl(mmio + HOST_EM_CTL);
+ if ((em_ctl & EM_CTL_TM) || (em_ctl & EM_CTL_RST))
+ return -EINVAL;
+
+ writel(em_ctl | EM_CTL_RST, mmio + HOST_EM_CTL);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ahci_reset_em);
+
+static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
+ ssize_t size)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *mmio = hpriv->mmio;
+ u32 em_ctl;
+ u32 message[] = {0, 0};
+ unsigned long flags;
+ int pmp;
+ struct ahci_em_priv *emp;
+
+ /* get the slot number from the message */
+ pmp = (state & EM_MSG_LED_PMP_SLOT) >> 8;
+ if (pmp < EM_MAX_SLOTS)
+ emp = &pp->em_priv[pmp];
+ else
+ return -EINVAL;
+
+ spin_lock_irqsave(ap->lock, flags);
+
+ /*
+ * if we are still busy transmitting a previous message,
+ * do not allow
+ */
+ em_ctl = readl(mmio + HOST_EM_CTL);
+ if (em_ctl & EM_CTL_TM) {
+ spin_unlock_irqrestore(ap->lock, flags);
+ return -EBUSY;
+ }
+
+ /*
+ * create message header - this is all zero except for
+ * the message size, which is 4 bytes.
+ */
+ message[0] |= (4 << 8);
+
+ /* ignore 0:4 of byte zero, fill in port info yourself */
+ message[1] = ((state & ~EM_MSG_LED_HBA_PORT) | ap->port_no);
+
+ /* write message to EM_LOC */
+ writel(message[0], mmio + hpriv->em_loc);
+ writel(message[1], mmio + hpriv->em_loc+4);
+
+ /* save off new led state for port/slot */
+ emp->led_state = state;
+
+ /*
+ * tell hardware to transmit the message
+ */
+ writel(em_ctl | EM_CTL_TM, mmio + HOST_EM_CTL);
+
+ spin_unlock_irqrestore(ap->lock, flags);
+ return size;
+}
+
+static ssize_t ahci_led_show(struct ata_port *ap, char *buf)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ata_link *link;
+ struct ahci_em_priv *emp;
+ int rc = 0;
+
+ ata_for_each_link(link, ap, EDGE) {
+ emp = &pp->em_priv[link->pmp];
+ rc += sprintf(buf, "%lx\n", emp->led_state);
+ }
+ return rc;
+}
+
+static ssize_t ahci_led_store(struct ata_port *ap, const char *buf,
+ size_t size)
+{
+ int state;
+ int pmp;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_em_priv *emp;
+
+ state = simple_strtoul(buf, NULL, 0);
+
+ /* get the slot number from the message */
+ pmp = (state & EM_MSG_LED_PMP_SLOT) >> 8;
+ if (pmp < EM_MAX_SLOTS)
+ emp = &pp->em_priv[pmp];
+ else
+ return -EINVAL;
+
+ /* mask off the activity bits if we are in sw_activity
+ * mode, user should turn off sw_activity before setting
+ * activity led through em_message
+ */
+ if (emp->blink_policy)
+ state &= ~EM_MSG_LED_VALUE_ACTIVITY;
+
+ return ahci_transmit_led_message(ap, state, size);
+}
+
+static ssize_t ahci_activity_store(struct ata_device *dev, enum sw_activity val)
+{
+ struct ata_link *link = dev->link;
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
+ u32 port_led_state = emp->led_state;
+
+ /* save the desired Activity LED behavior */
+ if (val == OFF) {
+ /* clear LFLAG */
+ link->flags &= ~(ATA_LFLAG_SW_ACTIVITY);
+
+ /* set the LED to OFF */
+ port_led_state &= EM_MSG_LED_VALUE_OFF;
+ port_led_state |= (ap->port_no | (link->pmp << 8));
+ ahci_transmit_led_message(ap, port_led_state, 4);
+ } else {
+ link->flags |= ATA_LFLAG_SW_ACTIVITY;
+ if (val == BLINK_OFF) {
+ /* set LED to ON for idle */
+ port_led_state &= EM_MSG_LED_VALUE_OFF;
+ port_led_state |= (ap->port_no | (link->pmp << 8));
+ port_led_state |= EM_MSG_LED_VALUE_ON; /* check this */
+ ahci_transmit_led_message(ap, port_led_state, 4);
+ }
+ }
+ emp->blink_policy = val;
+ return 0;
+}
+
+static ssize_t ahci_activity_show(struct ata_device *dev, char *buf)
+{
+ struct ata_link *link = dev->link;
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
+
+ /* display the saved value of activity behavior for this
+ * disk.
+ */
+ return sprintf(buf, "%d\n", emp->blink_policy);
+}
+
+static void ahci_port_init(struct device *dev, struct ata_port *ap,
+ int port_no, void __iomem *mmio,
+ void __iomem *port_mmio)
+{
+ const char *emsg = NULL;
+ int rc;
+ u32 tmp;
+
+ /* make sure port is not active */
+ rc = ahci_deinit_port(ap, &emsg);
+ if (rc)
+ dev_warn(dev, "%s (%d)\n", emsg, rc);
+
+ /* clear SError */
+ tmp = readl(port_mmio + PORT_SCR_ERR);
+ VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
+ writel(tmp, port_mmio + PORT_SCR_ERR);
+
+ /* clear port IRQ */
+ tmp = readl(port_mmio + PORT_IRQ_STAT);
+ VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
+ if (tmp)
+ writel(tmp, port_mmio + PORT_IRQ_STAT);
+
+ writel(1 << port_no, mmio + HOST_IRQ_STAT);
+}
+
+void ahci_init_controller(struct ata_host *host)
+{
+ struct ahci_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->mmio;
+ int i;
+ void __iomem *port_mmio;
+ u32 tmp;
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ port_mmio = ahci_port_base(ap);
+ if (ata_port_is_dummy(ap))
+ continue;
+
+ ahci_port_init(host->dev, ap, i, mmio, port_mmio);
+ }
+
+ tmp = readl(mmio + HOST_CTL);
+ VPRINTK("HOST_CTL 0x%x\n", tmp);
+ writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL);
+ tmp = readl(mmio + HOST_CTL);
+ VPRINTK("HOST_CTL 0x%x\n", tmp);
+}
+EXPORT_SYMBOL_GPL(ahci_init_controller);
+
+static void ahci_dev_config(struct ata_device *dev)
+{
+ struct ahci_host_priv *hpriv = dev->link->ap->host->private_data;
+
+ if (hpriv->flags & AHCI_HFLAG_SECT255) {
+ dev->max_sectors = 255;
+ ata_dev_printk(dev, KERN_INFO,
+ "SB600 AHCI: limiting to 255 sectors per cmd\n");
+ }
+}
+
+static unsigned int ahci_dev_classify(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ata_taskfile tf;
+ u32 tmp;
+
+ tmp = readl(port_mmio + PORT_SIG);
+ tf.lbah = (tmp >> 24) & 0xff;
+ tf.lbam = (tmp >> 16) & 0xff;
+ tf.lbal = (tmp >> 8) & 0xff;
+ tf.nsect = (tmp) & 0xff;
+
+ return ata_dev_classify(&tf);
+}
+
+static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
+ u32 opts)
+{
+ dma_addr_t cmd_tbl_dma;
+
+ cmd_tbl_dma = pp->cmd_tbl_dma + tag * AHCI_CMD_TBL_SZ;
+
+ pp->cmd_slot[tag].opts = cpu_to_le32(opts);
+ pp->cmd_slot[tag].status = 0;
+ pp->cmd_slot[tag].tbl_addr = cpu_to_le32(cmd_tbl_dma & 0xffffffff);
+ pp->cmd_slot[tag].tbl_addr_hi = cpu_to_le32((cmd_tbl_dma >> 16) >> 16);
+}
+
+int ahci_kick_engine(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
+ u32 tmp;
+ int busy, rc;
+
+ /* stop engine */
+ rc = ahci_stop_engine(ap);
+ if (rc)
+ goto out_restart;
+
+ /* need to do CLO?
+ * always do CLO if PMP is attached (AHCI-1.3 9.2)
+ */
+ busy = status & (ATA_BUSY | ATA_DRQ);
+ if (!busy && !sata_pmp_attached(ap)) {
+ rc = 0;
+ goto out_restart;
+ }
+
+ if (!(hpriv->cap & HOST_CAP_CLO)) {
+ rc = -EOPNOTSUPP;
+ goto out_restart;
+ }
+
+ /* perform CLO */
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp |= PORT_CMD_CLO;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ rc = 0;
+ tmp = ata_wait_register(port_mmio + PORT_CMD,
+ PORT_CMD_CLO, PORT_CMD_CLO, 1, 500);
+ if (tmp & PORT_CMD_CLO)
+ rc = -EIO;
+
+ /* restart engine */
+ out_restart:
+ ahci_start_engine(ap);
+ return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_kick_engine);
+
+static int ahci_exec_polled_cmd(struct ata_port *ap, int pmp,
+ struct ata_taskfile *tf, int is_cmd, u16 flags,
+ unsigned long timeout_msec)
+{
+ const u32 cmd_fis_len = 5; /* five dwords */
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u8 *fis = pp->cmd_tbl;
+ u32 tmp;
+
+ /* prep the command */
+ ata_tf_to_fis(tf, pmp, is_cmd, fis);
+ ahci_fill_cmd_slot(pp, 0, cmd_fis_len | flags | (pmp << 12));
+
+ /* issue & wait */
+ writel(1, port_mmio + PORT_CMD_ISSUE);
+
+ if (timeout_msec) {
+ tmp = ata_wait_register(port_mmio + PORT_CMD_ISSUE, 0x1, 0x1,
+ 1, timeout_msec);
+ if (tmp & 0x1) {
+ ahci_kick_engine(ap);
+ return -EBUSY;
+ }
+ } else
+ readl(port_mmio + PORT_CMD_ISSUE); /* flush */
+
+ return 0;
+}
+
+int ahci_do_softreset(struct ata_link *link, unsigned int *class,
+ int pmp, unsigned long deadline,
+ int (*check_ready)(struct ata_link *link))
+{
+ struct ata_port *ap = link->ap;
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ const char *reason = NULL;
+ unsigned long now, msecs;
+ struct ata_taskfile tf;
+ int rc;
+
+ DPRINTK("ENTER\n");
+
+ /* prepare for SRST (AHCI-1.1 10.4.1) */
+ rc = ahci_kick_engine(ap);
+ if (rc && rc != -EOPNOTSUPP)
+ ata_link_printk(link, KERN_WARNING,
+ "failed to reset engine (errno=%d)\n", rc);
+
+ ata_tf_init(link->device, &tf);
+
+ /* issue the first D2H Register FIS */
+ msecs = 0;
+ now = jiffies;
+ if (time_after(now, deadline))
+ msecs = jiffies_to_msecs(deadline - now);
+
+ tf.ctl |= ATA_SRST;
+ if (ahci_exec_polled_cmd(ap, pmp, &tf, 0,
+ AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY, msecs)) {
+ rc = -EIO;
+ reason = "1st FIS failed";
+ goto fail;
+ }
+
+ /* spec says at least 5us, but be generous and sleep for 1ms */
+ msleep(1);
+
+ /* issue the second D2H Register FIS */
+ tf.ctl &= ~ATA_SRST;
+ ahci_exec_polled_cmd(ap, pmp, &tf, 0, 0, 0);
+
+ /* wait for link to become ready */
+ rc = ata_wait_after_reset(link, deadline, check_ready);
+ if (rc == -EBUSY && hpriv->flags & AHCI_HFLAG_SRST_TOUT_IS_OFFLINE) {
+ /*
+ * Workaround for cases where link online status can't
+ * be trusted. Treat device readiness timeout as link
+ * offline.
+ */
+ ata_link_printk(link, KERN_INFO,
+ "device not ready, treating as offline\n");
+ *class = ATA_DEV_NONE;
+ } else if (rc) {
+ /* link occupied, -ENODEV too is an error */
+ reason = "device not ready";
+ goto fail;
+ } else
+ *class = ahci_dev_classify(ap);
+
+ DPRINTK("EXIT, class=%u\n", *class);
+ return 0;
+
+ fail:
+ ata_link_printk(link, KERN_ERR, "softreset failed (%s)\n", reason);
+ return rc;
+}
+
+int ahci_check_ready(struct ata_link *link)
+{
+ void __iomem *port_mmio = ahci_port_base(link->ap);
+ u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
+
+ return ata_check_ready(status);
+}
+EXPORT_SYMBOL_GPL(ahci_check_ready);
+
+static int ahci_softreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ int pmp = sata_srst_pmp(link);
+
+ DPRINTK("ENTER\n");
+
+ return ahci_do_softreset(link, class, pmp, deadline, ahci_check_ready);
+}
+EXPORT_SYMBOL_GPL(ahci_do_softreset);
+
+static int ahci_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+ struct ata_taskfile tf;
+ bool online;
+ int rc;
+
+ DPRINTK("ENTER\n");
+
+ ahci_stop_engine(ap);
+
+ /* clear D2H reception area to properly wait for D2H FIS */
+ ata_tf_init(link->device, &tf);
+ tf.command = 0x80;
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+
+ rc = sata_link_hardreset(link, timing, deadline, &online,
+ ahci_check_ready);
+
+ ahci_start_engine(ap);
+
+ if (online)
+ *class = ahci_dev_classify(ap);
+
+ DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
+ return rc;
+}
+
+static void ahci_postreset(struct ata_link *link, unsigned int *class)
+{
+ struct ata_port *ap = link->ap;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 new_tmp, tmp;
+
+ ata_std_postreset(link, class);
+
+ /* Make sure port's ATAPI bit is set appropriately */
+ new_tmp = tmp = readl(port_mmio + PORT_CMD);
+ if (*class == ATA_DEV_ATAPI)
+ new_tmp |= PORT_CMD_ATAPI;
+ else
+ new_tmp &= ~PORT_CMD_ATAPI;
+ if (new_tmp != tmp) {
+ writel(new_tmp, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+ }
+}
+
+static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl)
+{
+ struct scatterlist *sg;
+ struct ahci_sg *ahci_sg = cmd_tbl + AHCI_CMD_TBL_HDR_SZ;
+ unsigned int si;
+
+ VPRINTK("ENTER\n");
+
+ /*
+ * Next, the S/G list.
+ */
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
+ dma_addr_t addr = sg_dma_address(sg);
+ u32 sg_len = sg_dma_len(sg);
+
+ ahci_sg[si].addr = cpu_to_le32(addr & 0xffffffff);
+ ahci_sg[si].addr_hi = cpu_to_le32((addr >> 16) >> 16);
+ ahci_sg[si].flags_size = cpu_to_le32(sg_len - 1);
+ }
+
+ return si;
+}
+
+static int ahci_pmp_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+
+ if (!sata_pmp_attached(ap) || pp->fbs_enabled)
+ return ata_std_qc_defer(qc);
+ else
+ return sata_pmp_qc_defer_cmd_switch(qc);
+}
+
+static void ahci_qc_prep(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ int is_atapi = ata_is_atapi(qc->tf.protocol);
+ void *cmd_tbl;
+ u32 opts;
+ const u32 cmd_fis_len = 5; /* five dwords */
+ unsigned int n_elem;
+
+ /*
+ * Fill in command table information. First, the header,
+ * a SATA Register - Host to Device command FIS.
+ */
+ cmd_tbl = pp->cmd_tbl + qc->tag * AHCI_CMD_TBL_SZ;
+
+ ata_tf_to_fis(&qc->tf, qc->dev->link->pmp, 1, cmd_tbl);
+ if (is_atapi) {
+ memset(cmd_tbl + AHCI_CMD_TBL_CDB, 0, 32);
+ memcpy(cmd_tbl + AHCI_CMD_TBL_CDB, qc->cdb, qc->dev->cdb_len);
+ }
+
+ n_elem = 0;
+ if (qc->flags & ATA_QCFLAG_DMAMAP)
+ n_elem = ahci_fill_sg(qc, cmd_tbl);
+
+ /*
+ * Fill in command slot information.
+ */
+ opts = cmd_fis_len | n_elem << 16 | (qc->dev->link->pmp << 12);
+ if (qc->tf.flags & ATA_TFLAG_WRITE)
+ opts |= AHCI_CMD_WRITE;
+ if (is_atapi)
+ opts |= AHCI_CMD_ATAPI | AHCI_CMD_PREFETCH;
+
+ ahci_fill_cmd_slot(pp, qc->tag, opts);
+}
+
+static void ahci_fbs_dec_intr(struct ata_port *ap)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 fbs = readl(port_mmio + PORT_FBS);
+ int retries = 3;
+
+ DPRINTK("ENTER\n");
+ BUG_ON(!pp->fbs_enabled);
+
+ /* time to wait for DEC is not specified by AHCI spec,
+ * add a retry loop for safety.
+ */
+ writel(fbs | PORT_FBS_DEC, port_mmio + PORT_FBS);
+ fbs = readl(port_mmio + PORT_FBS);
+ while ((fbs & PORT_FBS_DEC) && retries--) {
+ udelay(1);
+ fbs = readl(port_mmio + PORT_FBS);
+ }
+
+ if (fbs & PORT_FBS_DEC)
+ dev_printk(KERN_ERR, ap->host->dev,
+ "failed to clear device error\n");
+}
+
+static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ata_eh_info *host_ehi = &ap->link.eh_info;
+ struct ata_link *link = NULL;
+ struct ata_queued_cmd *active_qc;
+ struct ata_eh_info *active_ehi;
+ bool fbs_need_dec = false;
+ u32 serror;
+
+ /* determine active link with error */
+ if (pp->fbs_enabled) {
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 fbs = readl(port_mmio + PORT_FBS);
+ int pmp = fbs >> PORT_FBS_DWE_OFFSET;
+
+ if ((fbs & PORT_FBS_SDE) && (pmp < ap->nr_pmp_links) &&
+ ata_link_online(&ap->pmp_link[pmp])) {
+ link = &ap->pmp_link[pmp];
+ fbs_need_dec = true;
+ }
+
+ } else
+ ata_for_each_link(link, ap, EDGE)
+ if (ata_link_active(link))
+ break;
+
+ if (!link)
+ link = &ap->link;
+
+ active_qc = ata_qc_from_tag(ap, link->active_tag);
+ active_ehi = &link->eh_info;
+
+ /* record irq stat */
+ ata_ehi_clear_desc(host_ehi);
+ ata_ehi_push_desc(host_ehi, "irq_stat 0x%08x", irq_stat);
+
+ /* AHCI needs SError cleared; otherwise, it might lock up */
+ ahci_scr_read(&ap->link, SCR_ERROR, &serror);
+ ahci_scr_write(&ap->link, SCR_ERROR, serror);
+ host_ehi->serror |= serror;
+
+ /* some controllers set IRQ_IF_ERR on device errors, ignore it */
+ if (hpriv->flags & AHCI_HFLAG_IGN_IRQ_IF_ERR)
+ irq_stat &= ~PORT_IRQ_IF_ERR;
+
+ if (irq_stat & PORT_IRQ_TF_ERR) {
+ /* If qc is active, charge it; otherwise, the active
+ * link. There's no active qc on NCQ errors. It will
+ * be determined by EH by reading log page 10h.
+ */
+ if (active_qc)
+ active_qc->err_mask |= AC_ERR_DEV;
+ else
+ active_ehi->err_mask |= AC_ERR_DEV;
+
+ if (hpriv->flags & AHCI_HFLAG_IGN_SERR_INTERNAL)
+ host_ehi->serror &= ~SERR_INTERNAL;
+ }
+
+ if (irq_stat & PORT_IRQ_UNK_FIS) {
+ u32 *unk = (u32 *)(pp->rx_fis + RX_FIS_UNK);
+
+ active_ehi->err_mask |= AC_ERR_HSM;
+ active_ehi->action |= ATA_EH_RESET;
+ ata_ehi_push_desc(active_ehi,
+ "unknown FIS %08x %08x %08x %08x" ,
+ unk[0], unk[1], unk[2], unk[3]);
+ }
+
+ if (sata_pmp_attached(ap) && (irq_stat & PORT_IRQ_BAD_PMP)) {
+ active_ehi->err_mask |= AC_ERR_HSM;
+ active_ehi->action |= ATA_EH_RESET;
+ ata_ehi_push_desc(active_ehi, "incorrect PMP");
+ }
+
+ if (irq_stat & (PORT_IRQ_HBUS_ERR | PORT_IRQ_HBUS_DATA_ERR)) {
+ host_ehi->err_mask |= AC_ERR_HOST_BUS;
+ host_ehi->action |= ATA_EH_RESET;
+ ata_ehi_push_desc(host_ehi, "host bus error");
+ }
+
+ if (irq_stat & PORT_IRQ_IF_ERR) {
+ if (fbs_need_dec)
+ active_ehi->err_mask |= AC_ERR_DEV;
+ else {
+ host_ehi->err_mask |= AC_ERR_ATA_BUS;
+ host_ehi->action |= ATA_EH_RESET;
+ }
+
+ ata_ehi_push_desc(host_ehi, "interface fatal error");
+ }
+
+ if (irq_stat & (PORT_IRQ_CONNECT | PORT_IRQ_PHYRDY)) {
+ ata_ehi_hotplugged(host_ehi);
+ ata_ehi_push_desc(host_ehi, "%s",
+ irq_stat & PORT_IRQ_CONNECT ?
+ "connection status changed" : "PHY RDY changed");
+ }
+
+ /* okay, let's hand over to EH */
+
+ if (irq_stat & PORT_IRQ_FREEZE)
+ ata_port_freeze(ap);
+ else if (fbs_need_dec) {
+ ata_link_abort(link);
+ ahci_fbs_dec_intr(ap);
+ } else
+ ata_port_abort(ap);
+}
+
+static void ahci_port_intr(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ int resetting = !!(ap->pflags & ATA_PFLAG_RESETTING);
+ u32 status, qc_active = 0;
+ int rc;
+
+ status = readl(port_mmio + PORT_IRQ_STAT);
+ writel(status, port_mmio + PORT_IRQ_STAT);
+
+ /* ignore BAD_PMP while resetting */
+ if (unlikely(resetting))
+ status &= ~PORT_IRQ_BAD_PMP;
+
+ /* If we are getting PhyRdy, this is
+ * just a power state change, we should
+ * clear out this, plus the PhyRdy/Comm
+ * Wake bits from Serror
+ */
+ if ((hpriv->flags & AHCI_HFLAG_NO_HOTPLUG) &&
+ (status & PORT_IRQ_PHYRDY)) {
+ status &= ~PORT_IRQ_PHYRDY;
+ ahci_scr_write(&ap->link, SCR_ERROR, ((1 << 16) | (1 << 18)));
+ }
+
+ if (unlikely(status & PORT_IRQ_ERROR)) {
+ ahci_error_intr(ap, status);
+ return;
+ }
+
+ if (status & PORT_IRQ_SDB_FIS) {
+ /* If SNotification is available, leave notification
+ * handling to sata_async_notification(). If not,
+ * emulate it by snooping SDB FIS RX area.
+ *
+ * Snooping FIS RX area is probably cheaper than
+ * poking SNotification but some constrollers which
+ * implement SNotification, ICH9 for example, don't
+ * store AN SDB FIS into receive area.
+ */
+ if (hpriv->cap & HOST_CAP_SNTF)
+ sata_async_notification(ap);
+ else {
+ /* If the 'N' bit in word 0 of the FIS is set,
+ * we just received asynchronous notification.
+ * Tell libata about it.
+ *
+ * Lack of SNotification should not appear in
+ * ahci 1.2, so the workaround is unnecessary
+ * when FBS is enabled.
+ */
+ if (pp->fbs_enabled)
+ WARN_ON_ONCE(1);
+ else {
+ const __le32 *f = pp->rx_fis + RX_FIS_SDB;
+ u32 f0 = le32_to_cpu(f[0]);
+ if (f0 & (1 << 15))
+ sata_async_notification(ap);
+ }
+ }
+ }
+
+ /* pp->active_link is not reliable once FBS is enabled, both
+ * PORT_SCR_ACT and PORT_CMD_ISSUE should be checked because
+ * NCQ and non-NCQ commands may be in flight at the same time.
+ */
+ if (pp->fbs_enabled) {
+ if (ap->qc_active) {
+ qc_active = readl(port_mmio + PORT_SCR_ACT);
+ qc_active |= readl(port_mmio + PORT_CMD_ISSUE);
+ }
+ } else {
+ /* pp->active_link is valid iff any command is in flight */
+ if (ap->qc_active && pp->active_link->sactive)
+ qc_active = readl(port_mmio + PORT_SCR_ACT);
+ else
+ qc_active = readl(port_mmio + PORT_CMD_ISSUE);
+ }
+
+
+ rc = ata_qc_complete_multiple(ap, qc_active);
+
+ /* while resetting, invalid completions are expected */
+ if (unlikely(rc < 0 && !resetting)) {
+ ehi->err_mask |= AC_ERR_HSM;
+ ehi->action |= ATA_EH_RESET;
+ ata_port_freeze(ap);
+ }
+}
+
+irqreturn_t ahci_interrupt(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ struct ahci_host_priv *hpriv;
+ unsigned int i, handled = 0;
+ void __iomem *mmio;
+ u32 irq_stat, irq_masked;
+
+ VPRINTK("ENTER\n");
+
+ hpriv = host->private_data;
+ mmio = hpriv->mmio;
+
+ /* sigh. 0xffffffff is a valid return from h/w */
+ irq_stat = readl(mmio + HOST_IRQ_STAT);
+ if (!irq_stat)
+ return IRQ_NONE;
+
+ irq_masked = irq_stat & hpriv->port_map;
+
+ spin_lock(&host->lock);
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap;
+
+ if (!(irq_masked & (1 << i)))
+ continue;
+
+ ap = host->ports[i];
+ if (ap) {
+ ahci_port_intr(ap);
+ VPRINTK("port %u\n", i);
+ } else {
+ VPRINTK("port %u (no irq)\n", i);
+ if (ata_ratelimit())
+ dev_printk(KERN_WARNING, host->dev,
+ "interrupt on disabled port %u\n", i);
+ }
+
+ handled = 1;
+ }
+
+ /* HOST_IRQ_STAT behaves as level triggered latch meaning that
+ * it should be cleared after all the port events are cleared;
+ * otherwise, it will raise a spurious interrupt after each
+ * valid one. Please read section 10.6.2 of ahci 1.1 for more
+ * information.
+ *
+ * Also, use the unmasked value to clear interrupt as spurious
+ * pending event on a dummy port might cause screaming IRQ.
+ */
+ writel(irq_stat, mmio + HOST_IRQ_STAT);
+
+ spin_unlock(&host->lock);
+
+ VPRINTK("EXIT\n");
+
+ return IRQ_RETVAL(handled);
+}
+EXPORT_SYMBOL_GPL(ahci_interrupt);
+
+static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_port_priv *pp = ap->private_data;
+
+ /* Keep track of the currently active link. It will be used
+ * in completion path to determine whether NCQ phase is in
+ * progress.
+ */
+ pp->active_link = qc->dev->link;
+
+ if (qc->tf.protocol == ATA_PROT_NCQ)
+ writel(1 << qc->tag, port_mmio + PORT_SCR_ACT);
+
+ if (pp->fbs_enabled && pp->fbs_last_dev != qc->dev->link->pmp) {
+ u32 fbs = readl(port_mmio + PORT_FBS);
+ fbs &= ~(PORT_FBS_DEV_MASK | PORT_FBS_DEC);
+ fbs |= qc->dev->link->pmp << PORT_FBS_DEV_OFFSET;
+ writel(fbs, port_mmio + PORT_FBS);
+ pp->fbs_last_dev = qc->dev->link->pmp;
+ }
+
+ writel(1 << qc->tag, port_mmio + PORT_CMD_ISSUE);
+
+ ahci_sw_activity(qc->dev->link);
+
+ return 0;
+}
+
+static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc)
+{
+ struct ahci_port_priv *pp = qc->ap->private_data;
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+
+ if (pp->fbs_enabled)
+ d2h_fis += qc->dev->link->pmp * AHCI_RX_FIS_SZ;
+
+ ata_tf_from_fis(d2h_fis, &qc->result_tf);
+ return true;
+}
+
+static void ahci_freeze(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+
+ /* turn IRQ off */
+ writel(0, port_mmio + PORT_IRQ_MASK);
+}
+
+static void ahci_thaw(struct ata_port *ap)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = hpriv->mmio;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 tmp;
+ struct ahci_port_priv *pp = ap->private_data;
+
+ /* clear IRQ */
+ tmp = readl(port_mmio + PORT_IRQ_STAT);
+ writel(tmp, port_mmio + PORT_IRQ_STAT);
+ writel(1 << ap->port_no, mmio + HOST_IRQ_STAT);
+
+ /* turn IRQ back on */
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+}
+
+static void ahci_error_handler(struct ata_port *ap)
+{
+ if (!(ap->pflags & ATA_PFLAG_FROZEN)) {
+ /* restart engine */
+ ahci_stop_engine(ap);
+ ahci_start_engine(ap);
+ }
+
+ sata_pmp_error_handler(ap);
+}
+
+static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+
+ /* make DMA engine forget about the failed command */
+ if (qc->flags & ATA_QCFLAG_FAILED)
+ ahci_kick_engine(ap);
+}
+
+static void ahci_enable_fbs(struct ata_port *ap)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 fbs;
+ int rc;
+
+ if (!pp->fbs_supported)
+ return;
+
+ fbs = readl(port_mmio + PORT_FBS);
+ if (fbs & PORT_FBS_EN) {
+ pp->fbs_enabled = true;
+ pp->fbs_last_dev = -1; /* initialization */
+ return;
+ }
+
+ rc = ahci_stop_engine(ap);
+ if (rc)
+ return;
+
+ writel(fbs | PORT_FBS_EN, port_mmio + PORT_FBS);
+ fbs = readl(port_mmio + PORT_FBS);
+ if (fbs & PORT_FBS_EN) {
+ dev_printk(KERN_INFO, ap->host->dev, "FBS is enabled.\n");
+ pp->fbs_enabled = true;
+ pp->fbs_last_dev = -1; /* initialization */
+ } else
+ dev_printk(KERN_ERR, ap->host->dev, "Failed to enable FBS\n");
+
+ ahci_start_engine(ap);
+}
+
+static void ahci_disable_fbs(struct ata_port *ap)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 fbs;
+ int rc;
+
+ if (!pp->fbs_supported)
+ return;
+
+ fbs = readl(port_mmio + PORT_FBS);
+ if ((fbs & PORT_FBS_EN) == 0) {
+ pp->fbs_enabled = false;
+ return;
+ }
+
+ rc = ahci_stop_engine(ap);
+ if (rc)
+ return;
+
+ writel(fbs & ~PORT_FBS_EN, port_mmio + PORT_FBS);
+ fbs = readl(port_mmio + PORT_FBS);
+ if (fbs & PORT_FBS_EN)
+ dev_printk(KERN_ERR, ap->host->dev, "Failed to disable FBS\n");
+ else {
+ dev_printk(KERN_INFO, ap->host->dev, "FBS is disabled.\n");
+ pp->fbs_enabled = false;
+ }
+
+ ahci_start_engine(ap);
+}
+
+static void ahci_pmp_attach(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_port_priv *pp = ap->private_data;
+ u32 cmd;
+
+ cmd = readl(port_mmio + PORT_CMD);
+ cmd |= PORT_CMD_PMP;
+ writel(cmd, port_mmio + PORT_CMD);
+
+ ahci_enable_fbs(ap);
+
+ pp->intr_mask |= PORT_IRQ_BAD_PMP;
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+}
+
+static void ahci_pmp_detach(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_port_priv *pp = ap->private_data;
+ u32 cmd;
+
+ ahci_disable_fbs(ap);
+
+ cmd = readl(port_mmio + PORT_CMD);
+ cmd &= ~PORT_CMD_PMP;
+ writel(cmd, port_mmio + PORT_CMD);
+
+ pp->intr_mask &= ~PORT_IRQ_BAD_PMP;
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+}
+
+static int ahci_port_resume(struct ata_port *ap)
+{
+ ahci_power_up(ap);
+ ahci_start_port(ap);
+
+ if (sata_pmp_attached(ap))
+ ahci_pmp_attach(ap);
+ else
+ ahci_pmp_detach(ap);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
+{
+ const char *emsg = NULL;
+ int rc;
+
+ rc = ahci_deinit_port(ap, &emsg);
+ if (rc == 0)
+ ahci_power_down(ap);
+ else {
+ ata_port_printk(ap, KERN_ERR, "%s (%d)\n", emsg, rc);
+ ahci_start_port(ap);
+ }
+
+ return rc;
+}
+#endif
+
+static int ahci_port_start(struct ata_port *ap)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ struct device *dev = ap->host->dev;
+ struct ahci_port_priv *pp;
+ void *mem;
+ dma_addr_t mem_dma;
+ size_t dma_sz, rx_fis_sz;
+
+ pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
+ if (!pp)
+ return -ENOMEM;
+
+ /* check FBS capability */
+ if ((hpriv->cap & HOST_CAP_FBS) && sata_pmp_supported(ap)) {
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 cmd = readl(port_mmio + PORT_CMD);
+ if (cmd & PORT_CMD_FBSCP)
+ pp->fbs_supported = true;
+ else
+ dev_printk(KERN_WARNING, dev,
+ "The port is not capable of FBS\n");
+ }
+
+ if (pp->fbs_supported) {
+ dma_sz = AHCI_PORT_PRIV_FBS_DMA_SZ;
+ rx_fis_sz = AHCI_RX_FIS_SZ * 16;
+ } else {
+ dma_sz = AHCI_PORT_PRIV_DMA_SZ;
+ rx_fis_sz = AHCI_RX_FIS_SZ;
+ }
+
+ mem = dmam_alloc_coherent(dev, dma_sz, &mem_dma, GFP_KERNEL);
+ if (!mem)
+ return -ENOMEM;
+ memset(mem, 0, dma_sz);
+
+ /*
+ * First item in chunk of DMA memory: 32-slot command table,
+ * 32 bytes each in size
+ */
+ pp->cmd_slot = mem;
+ pp->cmd_slot_dma = mem_dma;
+
+ mem += AHCI_CMD_SLOT_SZ;
+ mem_dma += AHCI_CMD_SLOT_SZ;
+
+ /*
+ * Second item: Received-FIS area
+ */
+ pp->rx_fis = mem;
+ pp->rx_fis_dma = mem_dma;
+
+ mem += rx_fis_sz;
+ mem_dma += rx_fis_sz;
+
+ /*
+ * Third item: data area for storing a single command
+ * and its scatter-gather table
+ */
+ pp->cmd_tbl = mem;
+ pp->cmd_tbl_dma = mem_dma;
+
+ /*
+ * Save off initial list of interrupts to be enabled.
+ * This could be changed later
+ */
+ pp->intr_mask = DEF_PORT_IRQ;
+
+ ap->private_data = pp;
+
+ /* engage engines, captain */
+ return ahci_port_resume(ap);
+}
+
+static void ahci_port_stop(struct ata_port *ap)
+{
+ const char *emsg = NULL;
+ int rc;
+
+ /* de-initialize port */
+ rc = ahci_deinit_port(ap, &emsg);
+ if (rc)
+ ata_port_printk(ap, KERN_WARNING, "%s (%d)\n", emsg, rc);
+}
+
+void ahci_print_info(struct ata_host *host, const char *scc_s)
+{
+ struct ahci_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->mmio;
+ u32 vers, cap, cap2, impl, speed;
+ const char *speed_s;
+
+ vers = readl(mmio + HOST_VERSION);
+ cap = hpriv->cap;
+ cap2 = hpriv->cap2;
+ impl = hpriv->port_map;
+
+ speed = (cap >> 20) & 0xf;
+ if (speed == 1)
+ speed_s = "1.5";
+ else if (speed == 2)
+ speed_s = "3";
+ else if (speed == 3)
+ speed_s = "6";
+ else
+ speed_s = "?";
+
+ dev_info(host->dev,
+ "AHCI %02x%02x.%02x%02x "
+ "%u slots %u ports %s Gbps 0x%x impl %s mode\n"
+ ,
+
+ (vers >> 24) & 0xff,
+ (vers >> 16) & 0xff,
+ (vers >> 8) & 0xff,
+ vers & 0xff,
+
+ ((cap >> 8) & 0x1f) + 1,
+ (cap & 0x1f) + 1,
+ speed_s,
+ impl,
+ scc_s);
+
+ dev_info(host->dev,
+ "flags: "
+ "%s%s%s%s%s%s%s"
+ "%s%s%s%s%s%s%s"
+ "%s%s%s%s%s%s\n"
+ ,
+
+ cap & HOST_CAP_64 ? "64bit " : "",
+ cap & HOST_CAP_NCQ ? "ncq " : "",
+ cap & HOST_CAP_SNTF ? "sntf " : "",
+ cap & HOST_CAP_MPS ? "ilck " : "",
+ cap & HOST_CAP_SSS ? "stag " : "",
+ cap & HOST_CAP_ALPM ? "pm " : "",
+ cap & HOST_CAP_LED ? "led " : "",
+ cap & HOST_CAP_CLO ? "clo " : "",
+ cap & HOST_CAP_ONLY ? "only " : "",
+ cap & HOST_CAP_PMP ? "pmp " : "",
+ cap & HOST_CAP_FBS ? "fbs " : "",
+ cap & HOST_CAP_PIO_MULTI ? "pio " : "",
+ cap & HOST_CAP_SSC ? "slum " : "",
+ cap & HOST_CAP_PART ? "part " : "",
+ cap & HOST_CAP_CCC ? "ccc " : "",
+ cap & HOST_CAP_EMS ? "ems " : "",
+ cap & HOST_CAP_SXS ? "sxs " : "",
+ cap2 & HOST_CAP2_APST ? "apst " : "",
+ cap2 & HOST_CAP2_NVMHCI ? "nvmp " : "",
+ cap2 & HOST_CAP2_BOH ? "boh " : ""
+ );
+}
+EXPORT_SYMBOL_GPL(ahci_print_info);
+
+void ahci_set_em_messages(struct ahci_host_priv *hpriv,
+ struct ata_port_info *pi)
+{
+ u8 messages;
+ void __iomem *mmio = hpriv->mmio;
+ u32 em_loc = readl(mmio + HOST_EM_LOC);
+ u32 em_ctl = readl(mmio + HOST_EM_CTL);
+
+ if (!ahci_em_messages || !(hpriv->cap & HOST_CAP_EMS))
+ return;
+
+ messages = (em_ctl & EM_CTRL_MSG_TYPE) >> 16;
+
+ /* we only support LED message type right now */
+ if ((messages & 0x01) && (ahci_em_messages == 1)) {
+ /* store em_loc */
+ hpriv->em_loc = ((em_loc >> 16) * 4);
+ pi->flags |= ATA_FLAG_EM;
+ if (!(em_ctl & EM_CTL_ALHD))
+ pi->flags |= ATA_FLAG_SW_ACTIVITY;
+ }
+}
+EXPORT_SYMBOL_GPL(ahci_set_em_messages);
+
+MODULE_AUTHOR("Jeff Garzik");
+MODULE_DESCRIPTION("Common AHCI SATA low-level routines");
+MODULE_LICENSE("GPL");
projects / kernel / kernel-generic.git / commitdiff