This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
bool "Support mpc8308_p1m"
select ARCH_MPC8308
-config TARGET_SBC8349
- bool "Support sbc8349"
- select ARCH_MPC8349
-
config TARGET_VE8313
bool "Support ve8313"
select ARCH_MPC8313
source "board/ids/ids8313/Kconfig"
source "board/keymile/Kconfig"
source "board/mpc8308_p1m/Kconfig"
-source "board/sbc8349/Kconfig"
source "board/tqc/tqm834x/Kconfig"
source "board/ve8313/Kconfig"
source "board/gdsys/mpc8308/Kconfig"
+++ /dev/null
-if TARGET_SBC8349
-
-config SYS_BOARD
- default "sbc8349"
-
-config SYS_CONFIG_NAME
- default "sbc8349"
-
-endif
+++ /dev/null
-SBC8349 BOARD
-M: Paul Gortmaker <paul.gortmaker@windriver.com>
-S: Maintained
-F: board/sbc8349/
-F: include/configs/sbc8349.h
-F: configs/sbc8349_defconfig
-F: configs/sbc8349_PCI_33_defconfig
-F: configs/sbc8349_PCI_66_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (c) 2006 Wind River Systems, Inc.
-
-obj-y += sbc8349.o
-obj-$(CONFIG_PCI) += pci.o
+++ /dev/null
-
-
- U-Boot for Wind River SBC834x Boards
- ====================================
-
-
-The Wind River SBC834x board is a 6U form factor (not CPCI) reference
-design that uses the MPC8347E or MPC8349E processor. U-Boot support
-for this board is heavily based on the existing U-Boot support for
-Freescale MPC8349 reference boards.
-
-Support has been primarily tested on the SBC8349 version of the board,
-although earlier versions were also tested on the SBC8347. The primary
-difference in the two is the level of PCI functionality.
-
- http://www.windriver.com/products/OCD/SBC8347E_49E/
-
-
-Flash Details:
-==============
-
-The flash type is intel 28F640Jx (4096x16) [one device]. Base address
-is 0xFF80_0000 which is also where the Hardware Reset Configuration
-Word (HRCW) is stored. Caution should be used to not reset the
-board without having a valid HRCW in place (i.e. erased flash) as
-then a Wind River ICE will be required to restore the HRCW and flash
-image.
-
-
-Restoring a corrupted or missing flash image:
-=============================================
-
-Note that U-Boot versions up to and including 2009.06 had essentially
-two copies of U-Boot in flash; one at the very beginning, which set
-the HRCW, and one at the very end, which was the image that was run.
-As of this point in time, the two have been combined into just one
-at the beginning of flash, which provides both the HRCW, and the image
-that is executed. This frees up the remainder of flash for other uses.
-Use of the U-Boot command "fli" will indicate what parts are in use.
-Details for storing U-Boot to flash using a Wind River ICE can be found
-on page 19 of the board manual (request ERG-00328-001). The following
-is a summary of that information:
-
- - Connect ICE and establish connection to it from WorkBench/OCD.
- - Ensure you have background mode (BKM) in the OCD terminal window.
- - Select the appropriate flash type (listed above)
- - Prepare a U-Boot image by using the Wind River Convert utility;
- by using "Convert and Add file" on the ELF file from your build.
- Convert from FF80_0000 to FFFF_FFFF (or to FF83_FFFF if you are
- trying to preserve your old environment settings and user flash).
- - Set the start address of the erase/flash process to FF80_0000
- - Set the target RAM required to 64kB.
- - Select sectors for erasing (see note on environment below)
- - Select Erase and Reprogram.
-
-Note that some versions of the register files used with Workbench
-would zero some TSEC registers, which inhibits ethernet operation
-by U-Boot when this register file is played to the target. Using
-"INN" in the OCD terminal window instead of "IN" before the "GO"
-will not play the register file, and allow U-Boot to use the TSEC
-interface while executed from the ICE "GO" command.
-
-Alternatively, you can locate the register file which will be named
-WRS_SBC8349_PCT00328001.reg or similar) and "REM" out all the lines
-beginning with "SCGA TSEC1" and "SCGA TSEC2". This allows you to
-use all the remaining register file content.
-
-If you wish to preserve your prior U-Boot environment settings,
-then convert (and erase to) 0xFF83FFFF instead of 0xFFFFFFFF.
-The size for converting (and erasing) must be at least as large
-as u-boot.bin.
-
-
-Updating U-Boot with U-Boot:
-============================
-
-This procedure is very similar to other boards that have U-Boot installed.
-Assuming that the network has been configured, and that the new u-boot.bin
-has been copied to the TFTP server, the commands are:
-
- tftp 200000 u-boot.bin
- protect off all
- erase ff800000 ff83ffff
- cp.b 200000 ff800000 40000
- protect on all
-
-You may wish to do a "md ff800000 20" operation as a prefix and postfix
-to the above steps to inspect/compare the HRCW before/after as an extra
-safety check before resetting the board upon completion of the reflash.
-
-PCI:
-====
-
-There are three configuration choices:
- sbc8349_config
- sbc8349_PCI_33_config
- sbc8349_PCI_66_config
-
-The 1st does not enable CONFIG_PCI, and assumes that the PCI slot
-will be left empty (M66EN high), and so the board will operate with
-a base clock of 66MHz. Note that you need both PCI enabled in U-Boot
-and linux in order to have functional PCI under linux. The only
-reason for choosing to not enable PCI would be if you had a very
-early (rev 1.0) CPU with possible PCI issues.
-
-The second enables PCI support and builds for a 33MHz clock rate. Note
-that if a 33MHz 32bit card is inserted in the slot, then the whole board
-will clock down to a 33MHz base clock instead of the default 66MHz. This
-will change the baud clocks and mess up your serial console output if you
-were previously running at 66MHz. If you want to use a 33MHz PCI card,
-then you should build a U-Boot with sbc8349_PCI_33_config and store this
-to flash prior to powering down the board and inserting the 33MHz PCI
-card.
-
-The third option builds PCI support in, and leaves the clocking at the
-default 66MHz. This has been tested with an intel PCI-X e1000 card.
-This is also the appropriate choice for people with a recent (non 1.0)
-CPU who currently have the PCI slot physically empty, but intend to
-possibly add a PCI-X card at a later date.
-
- => pci
- Scanning PCI devices on bus 0
- BusDevFun VendorId DeviceId Device Class Sub-Class
- _____________________________________________________________
- 00.00.00 0x1957 0x0080 Processor 0x20
- 00.11.00 0x8086 0x1026 Network controller 0x00
- =>
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * pci.c -- WindRiver SBC8349 PCI board support.
- * Copyright (c) 2006 Wind River Systems, Inc.
- * Copyright (C) 2006-2009 Freescale Semiconductor, Inc.
- *
- * Based on MPC8349 PCI support but w/o PIB related code.
- */
-
-#include <init.h>
-#include <asm/mmu.h>
-#include <asm/io.h>
-#include <common.h>
-#include <mpc83xx.h>
-#include <pci.h>
-#include <i2c.h>
-#include <asm/fsl_i2c.h>
-#include <linux/delay.h>
-
-static struct pci_region pci1_regions[] = {
- {
- bus_start: CONFIG_SYS_PCI1_MEM_BASE,
- phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
- size: CONFIG_SYS_PCI1_MEM_SIZE,
- flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- bus_start: CONFIG_SYS_PCI1_IO_BASE,
- phys_start: CONFIG_SYS_PCI1_IO_PHYS,
- size: CONFIG_SYS_PCI1_IO_SIZE,
- flags: PCI_REGION_IO
- },
- {
- bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
- phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
- size: CONFIG_SYS_PCI1_MMIO_SIZE,
- flags: PCI_REGION_MEM
- },
-};
-
-/*
- * pci_init_board()
- *
- * NOTICE: PCI2 is not supported. There is only one
- * physical PCI slot on the board.
- *
- */
-void
-pci_init_board(void)
-{
- volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
- struct pci_region *reg[] = { pci1_regions };
-
- /* Enable all 8 PCI_CLK_OUTPUTS */
- clk->occr = 0xff000000;
- udelay(2000);
-
- /* Configure PCI Local Access Windows */
- pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
-
- pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M;
-
- udelay(2000);
-
- mpc83xx_pci_init(1, reg);
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * sbc8349.c -- WindRiver SBC8349 board support.
- * Copyright (c) 2006-2007 Wind River Systems, Inc.
- *
- * Paul Gortmaker <paul.gortmaker@windriver.com>
- * Based on board/mpc8349emds/mpc8349emds.c (and previous 834x releases.)
- */
-
-#include <common.h>
-#include <fdt_support.h>
-#include <init.h>
-#include <ioports.h>
-#include <mpc83xx.h>
-#include <asm/bitops.h>
-#include <asm/global_data.h>
-#include <asm/mpc8349_pci.h>
-#include <i2c.h>
-#include <spd_sdram.h>
-#include <miiphy.h>
-#if defined(CONFIG_OF_LIBFDT)
-#include <linux/libfdt.h>
-#endif
-#include <linux/delay.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int fixed_sdram(void);
-void sdram_init(void);
-
-#if defined(CONFIG_DDR_ECC) && defined(CONFIG_MPC83xx)
-void ddr_enable_ecc(unsigned int dram_size);
-#endif
-
-#ifdef CONFIG_BOARD_EARLY_INIT_F
-int board_early_init_f (void)
-{
- return 0;
-}
-#endif
-
-#define ns2clk(ns) (ns / (1000000000 / CONFIG_8349_CLKIN) + 1)
-
-int dram_init(void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- u32 msize = 0;
-
- if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
- return -1;
-
- /* DDR SDRAM - Main SODIMM */
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_SDRAM_BASE & LAWBAR_BAR;
-#if defined(CONFIG_SPD_EEPROM)
- msize = spd_sdram();
-#else
- msize = fixed_sdram();
-#endif
- /*
- * Initialize SDRAM if it is on local bus.
- */
- sdram_init();
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /*
- * Initialize and enable DDR ECC.
- */
- ddr_enable_ecc(msize * 1024 * 1024);
-#endif
- /* set total bus SDRAM size(bytes) -- DDR */
- gd->ram_size = msize * 1024 * 1024;
-
- return 0;
-}
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-int fixed_sdram(void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- u32 msize = CONFIG_SYS_DDR_SIZE;
- u32 ddr_size = msize << 20; /* DDR size in bytes */
- u32 ddr_size_log2 = __ilog2(msize);
-
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_SDRAM_BASE & 0xfffff000;
- im->sysconf.ddrlaw[0].ar = LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
-
-#if (CONFIG_SYS_DDR_SIZE != 256)
-#warning Currently any ddr size other than 256 is not supported
-#endif
-
-#if ((CONFIG_SYS_SDRAM_BASE & 0x00FFFFFF) != 0)
-#warning Chip select bounds is only configurable in 16MB increments
-#endif
- im->ddr.csbnds[2].csbnds =
- ((CONFIG_SYS_SDRAM_BASE >> CSBNDS_SA_SHIFT) & CSBNDS_SA) |
- (((CONFIG_SYS_SDRAM_BASE + ddr_size - 1) >>
- CSBNDS_EA_SHIFT) & CSBNDS_EA);
- im->ddr.cs_config[2] = CONFIG_SYS_DDR_CS2_CONFIG;
-
- /* currently we use only one CS, so disable the other banks */
- im->ddr.cs_config[0] = 0;
- im->ddr.cs_config[1] = 0;
- im->ddr.cs_config[3] = 0;
-
- im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
-
- im->ddr.sdram_cfg =
- SDRAM_CFG_SREN
-#if defined(CONFIG_DDR_2T_TIMING)
- | SDRAM_CFG_2T_EN
-#endif
- | SDRAM_CFG_SDRAM_TYPE_DDR1;
-#if defined (CONFIG_DDR_32BIT)
- /* for 32-bit mode burst length is 8 */
- im->ddr.sdram_cfg |= (SDRAM_CFG_32_BE | SDRAM_CFG_8_BE);
-#endif
- im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
-
- im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
- udelay(200);
-
- /* enable DDR controller */
- im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
- return msize;
-}
-#endif/*!CONFIG_SYS_SPD_EEPROM*/
-
-
-int checkboard (void)
-{
- puts("Board: Wind River SBC834x\n");
- return 0;
-}
-
-/*
- * if board is fitted with SDRAM
- */
-#if defined(CONFIG_SYS_BR2_PRELIM) \
- && defined(CONFIG_SYS_OR2_PRELIM) \
- && defined(CONFIG_SYS_LBLAWBAR2_PRELIM) \
- && defined(CONFIG_SYS_LBLAWAR2_PRELIM)
-/*
- * Initialize SDRAM memory on the Local Bus.
- */
-
-void sdram_init(void)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile fsl_lbc_t *lbc = &immap->im_lbc;
- uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
- const u32 lsdmr_common = LSDMR_RFEN | LSDMR_BSMA1516 | LSDMR_RFCR8 |
- LSDMR_PRETOACT6 | LSDMR_ACTTORW3 | LSDMR_BL8 |
- LSDMR_WRC3 | LSDMR_CL3;
-
- puts("\n SDRAM on Local Bus: ");
- print_size (CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
-
- /*
- * Setup SDRAM Base and Option Registers, already done in cpu_init.c
- */
-
- /* setup mtrpt, lsrt and lbcr for LB bus */
- lbc->lbcr = 0x00000000;
- /* LB refresh timer prescal, 266MHz/32 */
- lbc->mrtpr = 0x20000000;
- /* LB sdram refresh timer, about 6us */
- lbc->lsrt = 0x32000000;
- asm("sync");
-
- /*
- * Configure the SDRAM controller Machine Mode Register.
- */
- /* 0x40636733; normal operation */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
-
- /* 0x68636733; precharge all the banks */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
- asm("sync");
- *sdram_addr = 0xff;
- udelay(100);
-
- /* 0x48636733; auto refresh */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
- asm("sync");
- /*1 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*2 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*3 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*4 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*5 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*6 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*7 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*8 times*/
- *sdram_addr = 0xff;
- udelay(100);
-
- /* 0x58636733; mode register write operation */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
- asm("sync");
- *sdram_addr = 0xff;
- udelay(100);
-
- /* 0x40636733; normal operation */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
- asm("sync");
- *sdram_addr = 0xff;
- udelay(100);
-}
-#else
-void sdram_init(void)
-{
- puts(" SDRAM on Local Bus: Disabled in config\n");
-}
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
- ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI
- ft_pci_setup(blob, bd);
-#endif
-
- return 0;
-}
-#endif
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFF800000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=33000000
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_SBC8349=y
-CONFIG_DDR_MC_CLOCK_MODE_1_1=y
-CONFIG_SYSTEM_PLL_FACTOR_8_1=y
-CONFIG_CORE_PLL_RATIO_2_1=y
-CONFIG_PCI_HOST_MODE_ENABLE=y
-CONFIG_PCI_64BIT_MODE_ENABLE=y
-CONFIG_PCI_INT_ARBITER1_ENABLE=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC1_MODE_GMII=y
-CONFIG_TSEC2_MODE_GMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="PCI1_MEM"
-CONFIG_BAT1_BASE=0x80000000
-CONFIG_BAT1_LENGTH_256_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="PCI1_MMIO"
-CONFIG_BAT2_BASE=0x90000000
-CONFIG_BAT2_LENGTH_256_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_INHIBITED=y
-CONFIG_BAT2_ICACHE_GUARDED=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="IMMR_PCIIO"
-CONFIG_BAT5_BASE=0xE0000000
-CONFIG_BAT5_LENGTH_256_MBYTES=y
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_ICACHE_INHIBITED=y
-CONFIG_BAT5_ICACHE_GUARDED=y
-CONFIG_BAT5_DCACHE_INHIBITED=y
-CONFIG_BAT5_DCACHE_GUARDED=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT6=y
-CONFIG_BAT6_NAME="LBC_INITRAM_FLASH"
-CONFIG_BAT6_BASE=0xF0000000
-CONFIG_BAT6_LENGTH_256_MBYTES=y
-CONFIG_BAT6_ACCESS_RW=y
-CONFIG_BAT6_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_ICACHE_GUARDED=y
-CONFIG_BAT6_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_DCACHE_GUARDED=y
-CONFIG_BAT6_USER_MODE_VALID=y
-CONFIG_BAT6_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFF800000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_8_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFF800000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_8_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_OR0_EAD_EXTRA=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_4=y
-CONFIG_PCI_64BIT=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="PCI_33M"
-CONFIG_BOOTDELAY=6
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xFF840000
-CONFIG_ENV_ADDR_REDUND=0xFF860000
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFF800000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=66000000
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_SBC8349=y
-CONFIG_DDR_MC_CLOCK_MODE_1_1=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_2_1=y
-CONFIG_PCI_HOST_MODE_ENABLE=y
-CONFIG_PCI_64BIT_MODE_ENABLE=y
-CONFIG_PCI_INT_ARBITER1_ENABLE=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC1_MODE_GMII=y
-CONFIG_TSEC2_MODE_GMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="PCI1_MEM"
-CONFIG_BAT1_BASE=0x80000000
-CONFIG_BAT1_LENGTH_256_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="PCI1_MMIO"
-CONFIG_BAT2_BASE=0x90000000
-CONFIG_BAT2_LENGTH_256_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_INHIBITED=y
-CONFIG_BAT2_ICACHE_GUARDED=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="IMMR_PCIIO"
-CONFIG_BAT5_BASE=0xE0000000
-CONFIG_BAT5_LENGTH_256_MBYTES=y
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_ICACHE_INHIBITED=y
-CONFIG_BAT5_ICACHE_GUARDED=y
-CONFIG_BAT5_DCACHE_INHIBITED=y
-CONFIG_BAT5_DCACHE_GUARDED=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT6=y
-CONFIG_BAT6_NAME="LBC_INITRAM_FLASH"
-CONFIG_BAT6_BASE=0xF0000000
-CONFIG_BAT6_LENGTH_256_MBYTES=y
-CONFIG_BAT6_ACCESS_RW=y
-CONFIG_BAT6_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_ICACHE_GUARDED=y
-CONFIG_BAT6_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_DCACHE_GUARDED=y
-CONFIG_BAT6_USER_MODE_VALID=y
-CONFIG_BAT6_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFF800000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_8_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFF800000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_8_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_OR0_EAD_EXTRA=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_4=y
-CONFIG_PCI_64BIT=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="PCI_66M"
-CONFIG_BOOTDELAY=6
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xFF840000
-CONFIG_ENV_ADDR_REDUND=0xFF860000
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFF800000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=66000000
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_SBC8349=y
-CONFIG_DDR_MC_CLOCK_MODE_1_1=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_2_1=y
-CONFIG_PCI_HOST_MODE_ENABLE=y
-CONFIG_PCI_INT_ARBITER1_ENABLE=y
-CONFIG_PCI_INT_ARBITER2_ENABLE=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC1_MODE_GMII=y
-CONFIG_TSEC2_MODE_GMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="IMMR_PCIIO"
-CONFIG_BAT5_BASE=0xE0000000
-CONFIG_BAT5_LENGTH_256_MBYTES=y
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_ICACHE_INHIBITED=y
-CONFIG_BAT5_ICACHE_GUARDED=y
-CONFIG_BAT5_DCACHE_INHIBITED=y
-CONFIG_BAT5_DCACHE_GUARDED=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT6=y
-CONFIG_BAT6_NAME="LBC_INITRAM_FLASH"
-CONFIG_BAT6_BASE=0xF0000000
-CONFIG_BAT6_LENGTH_256_MBYTES=y
-CONFIG_BAT6_ACCESS_RW=y
-CONFIG_BAT6_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_ICACHE_GUARDED=y
-CONFIG_BAT6_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_DCACHE_GUARDED=y
-CONFIG_BAT6_USER_MODE_VALID=y
-CONFIG_BAT6_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFF800000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_8_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFF800000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_8_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_OR0_EAD_EXTRA=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_4=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=6
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xFF840000
-CONFIG_ENV_ADDR_REDUND=0xFF860000
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_TSEC_ENET=y
-# CONFIG_PCI is not set
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * WindRiver SBC8349 U-Boot configuration file.
- * Copyright (c) 2006, 2007 Wind River Systems, Inc.
- *
- * Paul Gortmaker <paul.gortmaker@windriver.com>
- * Based on the MPC8349EMDS config.
- */
-
-/*
- * sbc8349 board configuration file.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 Family */
-
-/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
-#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
-
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-
-/*
- * DDR Setup
- */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
-#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
-#define CONFIG_SYS_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */
-
-/*
- * 32-bit data path mode.
- *
- * Please note that using this mode for devices with the real density of 64-bit
- * effectively reduces the amount of available memory due to the effect of
- * wrapping around while translating address to row/columns, for example in the
- * 256MB module the upper 128MB get aliased with contents of the lower
- * 128MB); normally this define should be used for devices with real 32-bit
- * data path.
- */
-#undef CONFIG_DDR_32BIT
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
-#define CONFIG_DDR_2T_TIMING
-
-#if defined(CONFIG_SPD_EEPROM)
-/*
- * Determine DDR configuration from I2C interface.
- */
-#define SPD_EEPROM_ADDRESS 0x52 /* DDR DIMM */
-
-#else
-/*
- * Manually set up DDR parameters
- * NB: manual DDR setup untested on sbc834x
- */
-#define CONFIG_SYS_DDR_SIZE 256 /* MB */
-#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ROW_BIT_13 \
- | CSCONFIG_COL_BIT_10)
-#define CONFIG_SYS_DDR_TIMING_1 0x36332321
-#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
-#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */
-
-#if defined(CONFIG_DDR_32BIT)
-/* set burst length to 8 for 32-bit data path */
- /* DLL,normal,seq,4/2.5, 8 burst len */
-#define CONFIG_SYS_DDR_MODE 0x00000023
-#else
-/* the default burst length is 4 - for 64-bit data path */
- /* DLL,normal,seq,4/2.5, 4 burst len */
-#define CONFIG_SYS_DDR_MODE 0x00000022
-#endif
-#endif
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* start of FLASH */
-#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
- /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000
- /* Size of used area in RAM*/
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
-
-#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69}, {1, 0x69} }
-/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
-
-/* TSEC */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
-
-#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
-#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
-#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
-#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
-
-#if defined(CONFIG_PCI)
-
-
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xFIXME
- #define PCI_ENET0_MEMADDR 0xFIXME
- #define PCI_IDSEL_NUMBER 0xFIXME
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
-#endif /* CONFIG_PCI */
-
-/*
- * TSEC configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define CONFIG_PHY_BCM5421S 1
-#define TSEC1_PHY_ADDR 0x19
-#define TSEC2_PHY_ADDR 0x1a
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#ifndef CONFIG_SYS_RAMBOOT
-/* Address and size of Redundant Environment Sector */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
- /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-
-#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH 0
-#define CONFIG_SYS_SICRL SICRL_LDP_A
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_HOSTNAME "SBC8349"
-#define CONFIG_ROOTPATH "/tftpboot/rootfs"
-#define CONFIG_BOOTFILE "uImage"
-
- /* default location for tftp and bootm */
-#define CONFIG_LOADADDR 800000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=sbc8349\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0" \
- "update=protect off ff800000 ff83ffff; " \
- "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
- "upd=run load update\0" \
- "fdtaddr=780000\0" \
- "fdtfile=sbc8349.dtb\0" \
- ""
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
- "$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / commitdiff