staging: octeon-usb: delete cvmx_usbnx_clk_ctl_cn50xx

Add the missing bits to common clk ctl definition, and we can delete
duplicated definitions.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/staging/octeon-usb/cvmx-usbnx-defs.h b/drivers/staging/octeon-usb/cvmx-usbnx-defs.h
index c73df64..87e9f33 100644 (file)
--- a/drivers/staging/octeon-usb/cvmx-usbnx-defs.h
+++ b/drivers/staging/octeon-usb/cvmx-usbnx-defs.h
@@ -93,6 +93,16 @@ union cvmx_usbnx_clk_ctl {
         *      suspend.
         *      The value of this field must be set while POR is
         *      active.
+        * @p_rtype: PHY reference clock type (CN50XX/CN52XX/CN56XX only)
+        *      '0' The USB-PHY uses a 12MHz crystal as a clock
+        *      source at the USB_XO and USB_XI pins
+        *      '1' Reserved
+        *      '2' The USB_PHY uses 12/24/48MHz 2.5V board clock
+        *      at the USB_XO pin. USB_XI should be tied to
+        *      ground in this case.
+        *      '3' Reserved
+        *      (bit 14 was P_XENBN on 3xxx)
+        *      (bit 15 was P_RCLK on 3xxx)
         * @p_com_on: '0' Force USB-PHY XO Bias, Bandgap and PLL to
         *      remain powered in Suspend Mode.
         *      '1' The USB-PHY XO Bias, Bandgap and PLL are
@@ -147,7 +157,7 @@ union cvmx_usbnx_clk_ctl {
                uint64_t divide2        : 2;
                uint64_t hclk_rst       : 1;
                uint64_t p_x_on         : 1;
-               uint64_t reserved_14_15 : 2;
+               uint64_t p_rtype        : 2;
                uint64_t p_com_on       : 1;
                uint64_t p_c_sel        : 2;
                uint64_t cdiv_byp       : 1;
@@ -243,99 +253,6 @@ union cvmx_usbnx_clk_ctl {
                uint64_t divide         : 3;
        } cn30xx;
        struct cvmx_usbnx_clk_ctl_cn30xx cn31xx;
-       /**
-        * struct cvmx_usbnx_clk_ctl_cn50xx
-        * @divide2: The 'hclk' used by the USB subsystem is derived
-        *      from the eclk.
-        *      Also see the field DIVIDE. DIVIDE2<1> must currently
-        *      be zero because it is not implemented, so the maximum
-        *      ratio of eclk/hclk is currently 16.
-        *      The actual divide number for hclk is:
-        *      (DIVIDE2 + 1) * (DIVIDE + 1)
-        * @hclk_rst: When this field is '0' the HCLK-DIVIDER used to
-        *      generate the hclk in the USB Subsystem is held
-        *      in reset. This bit must be set to '0' before
-        *      changing the value os DIVIDE in this register.
-        *      The reset to the HCLK_DIVIDERis also asserted
-        *      when core reset is asserted.
-        * @p_rtype: PHY reference clock type
-        *      '0' The USB-PHY uses a 12MHz crystal as a clock
-        *      source at the USB_XO and USB_XI pins
-        *      '1' Reserved
-        *      '2' The USB_PHY uses 12/24/48MHz 2.5V board clock
-        *      at the USB_XO pin. USB_XI should be tied to
-        *      ground in this case.
-        *      '3' Reserved
-        *      (bit 14 was P_XENBN on 3xxx)
-        *      (bit 15 was P_RCLK on 3xxx)
-        * @p_com_on: '0' Force USB-PHY XO Bias, Bandgap and PLL to
-        *      remain powered in Suspend Mode.
-        *      '1' The USB-PHY XO Bias, Bandgap and PLL are
-        *      powered down in suspend mode.
-        *      The value of this field must be set while POR is
-        *      active.
-        * @p_c_sel: Phy clock speed select.
-        *      Selects the reference clock / crystal frequency.
-        *      '11': Reserved
-        *      '10': 48 MHz (reserved when a crystal is used)
-        *      '01': 24 MHz (reserved when a crystal is used)
-        *      '00': 12 MHz
-        *      The value of this field must be set while POR is
-        *      active.
-        *      NOTE: if a crystal is used as a reference clock,
-        *      this field must be set to 12 MHz.
-        * @cdiv_byp: Used to enable the bypass input to the USB_CLK_DIV.
-        * @sd_mode: Scaledown mode for the USBC. Control timing events
-        *      in the USBC, for normal operation this must be '0'.
-        * @s_bist: Starts bist on the hclk memories, during the '0'
-        *      to '1' transition.
-        * @por: Power On Reset for the PHY.
-        *      Resets all the PHYS registers and state machines.
-        * @enable: When '1' allows the generation of the hclk. When
-        *      '0' the hclk will not be generated. SEE DIVIDE
-        *      field of this register.
-        * @prst: When this field is '0' the reset associated with
-        *      the phy_clk functionality in the USB Subsystem is
-        *      help in reset. This bit should not be set to '1'
-        *      until the time it takes 6 clocks (hclk or phy_clk,
-        *      whichever is slower) has passed. Under normal
-        *      operation once this bit is set to '1' it should not
-        *      be set to '0'.
-        * @hrst: When this field is '0' the reset associated with
-        *      the hclk functioanlity in the USB Subsystem is
-        *      held in reset.This bit should not be set to '1'
-        *      until 12ms after phy_clk is stable. Under normal
-        *      operation, once this bit is set to '1' it should
-        *      not be set to '0'.
-        * @divide: The frequency of 'hclk' used by the USB subsystem
-        *      is the eclk frequency divided by the value of
-        *      (DIVIDE2 + 1) * (DIVIDE + 1), also see the field
-        *      DIVIDE2 of this register.
-        *      The hclk frequency should be less than 125Mhz.
-        *      After writing a value to this field the SW should
-        *      read the field for the value written.
-        *      The ENABLE field of this register should not be set
-        *      until AFTER this field is set and then read.
-        */
-       struct cvmx_usbnx_clk_ctl_cn50xx {
-               uint64_t reserved_20_63 : 44;
-               uint64_t divide2        : 2;
-               uint64_t hclk_rst       : 1;
-               uint64_t reserved_16_16 : 1;
-               uint64_t p_rtype        : 2;
-               uint64_t p_com_on       : 1;
-               uint64_t p_c_sel        : 2;
-               uint64_t cdiv_byp       : 1;
-               uint64_t sd_mode        : 2;
-               uint64_t s_bist         : 1;
-               uint64_t por            : 1;
-               uint64_t enable         : 1;
-               uint64_t prst           : 1;
-               uint64_t hrst           : 1;
-               uint64_t divide         : 3;
-       } cn50xx;
-       struct cvmx_usbnx_clk_ctl_cn50xx cn52xx;
-       struct cvmx_usbnx_clk_ctl_cn50xx cn56xx;
 };
 
 /**

diff --git a/drivers/staging/octeon-usb/octeon-hcd.c b/drivers/staging/octeon-usb/octeon-hcd.c
index 1859c05..a5c4622 100644 (file)
--- a/drivers/staging/octeon-usb/octeon-hcd.c
+++ b/drivers/staging/octeon-usb/octeon-hcd.c
@@ -842,10 +842,10 @@ static int cvmx_usb_initialize(struct cvmx_usb_state *usb,
                        usbn_clk_ctl.cn31xx.p_xenbn = 0;
                } else if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN50XX))
                        /* From CN56XX,CN50XX manual */
-                       usbn_clk_ctl.cn56xx.p_rtype = 2;
+                       usbn_clk_ctl.s.p_rtype = 2;
                else
                        /* From CN52XX manual */
-                       usbn_clk_ctl.cn52xx.p_rtype = 1;
+                       usbn_clk_ctl.s.p_rtype = 1;
 
                switch (flags & CVMX_USB_INITIALIZE_FLAGS_CLOCK_MHZ_MASK) {
                case CVMX_USB_INITIALIZE_FLAGS_CLOCK_12MHZ:
@@ -869,10 +869,10 @@ static int cvmx_usb_initialize(struct cvmx_usb_state *usb,
                        usbn_clk_ctl.cn31xx.p_xenbn = 1;
                } else if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN50XX))
                        /* From CN56XX,CN50XX manual */
-                       usbn_clk_ctl.cn56xx.p_rtype = 0;
+                       usbn_clk_ctl.s.p_rtype = 0;
                else
                        /* From CN52XX manual */
-                       usbn_clk_ctl.cn52xx.p_rtype = 0;
+                       usbn_clk_ctl.s.p_rtype = 0;
 
                usbn_clk_ctl.s.p_c_sel = 0;
        }