zynq-zturn-myir.dtb \
zynq-zybo.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += \
- zynqmp-ep108.dtb \
zynqmp-mini-emmc.dtb \
zynqmp-mini-nand.dtb \
zynqmp-zcu102-revA.dtb \
+++ /dev/null
-/*
- * clock specification for Xilinx ZynqMP ep108 development board
- *
- * (C) Copyright 2015, Xilinx, Inc.
- *
- * Michal Simek <michal.simek@xilinx.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/ {
- misc_clk: misc_clk {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- u-boot,dm-pre-reloc;
- };
-
- i2c_clk: i2c_clk {
- compatible = "fixed-clock";
- #clock-cells = <0x0>;
- clock-frequency = <111111111>;
- };
-
- sata_clk: sata_clk {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <75000000>;
- };
-
- dp_aclk: clock0 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <50000000>;
- clock-accuracy = <100>;
- };
-
- clk100: clk100 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <100000000>;
- };
-
- clk600: clk600 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <600000000>;
- };
-
- dp_aud_clk: clock1 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <22579200>;
- clock-accuracy = <100>;
- };
-};
-
-&can0 {
- clocks = <&misc_clk &misc_clk>;
-};
-
-&can1 {
- clocks = <&misc_clk &misc_clk>;
-};
-
-&fpd_dma_chan1 {
- clocks = <&clk600>, <&clk100>;
-};
-
-&fpd_dma_chan2 {
- clocks = <&clk600>, <&clk100>;
-};
-
-&fpd_dma_chan3 {
- clocks = <&clk600>, <&clk100>;
-};
-
-&fpd_dma_chan4 {
- clocks = <&clk600>, <&clk100>;
-};
-
-&fpd_dma_chan5 {
- clocks = <&clk600>, <&clk100>;
-};
-
-&fpd_dma_chan6 {
- clocks = <&clk600>, <&clk100>;
-};
-
-&fpd_dma_chan7 {
- clocks = <&clk600>, <&clk100>;
-};
-
-&fpd_dma_chan8 {
- clocks = <&clk600>, <&clk100>;
-};
-
-&gem0 {
- clocks = <&misc_clk>, <&misc_clk>, <&misc_clk>;
-};
-
-&gpio {
- clocks = <&misc_clk>;
-};
-
-&i2c0 {
- clocks = <&i2c_clk>;
-};
-
-&i2c1 {
- clocks = <&i2c_clk>;
-};
-
-&nand0 {
- clocks = <&misc_clk &misc_clk>;
-};
-
-&qspi {
- clocks = <&misc_clk &misc_clk>;
-};
-
-&sata {
- clocks = <&sata_clk>;
-};
-
-&sdhci0 {
- clocks = <&misc_clk>, <&misc_clk>;
-};
-
-&sdhci1 {
- clocks = <&misc_clk>, <&misc_clk>;
-};
-
-&spi0 {
- clocks = <&misc_clk &misc_clk>;
-};
-
-&spi1 {
- clocks = <&misc_clk &misc_clk>;
-};
-
-&uart0 {
- clocks = <&misc_clk &misc_clk>;
-};
-
-&usb0 {
- clocks = <&misc_clk>, <&misc_clk>;
-};
-
-&usb1 {
- clocks = <&misc_clk>, <&misc_clk>;
-};
-
-&watchdog0 {
- clocks= <&misc_clk>;
-};
-
-&xilinx_drm {
- clocks = <&misc_clk>;
-};
-
-&xlnx_dp {
- clocks = <&dp_aclk>, <&dp_aud_clk>;
-};
-
-&xlnx_dp_snd_codec0 {
- clocks = <&dp_aud_clk>;
-};
-
-&xlnx_dpdma {
- clocks = <&misc_clk>;
-};
+++ /dev/null
-/*
- * dts file for Xilinx ZynqMP ep108 development board
- *
- * (C) Copyright 2014 - 2015, Xilinx, Inc.
- *
- * Michal Simek <michal.simek@xilinx.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/dts-v1/;
-
-#include "zynqmp.dtsi"
-#include "zynqmp-ep108-clk.dtsi"
-
-/ {
- model = "ZynqMP EP108";
-
- aliases {
- ethernet0 = &gem0;
- mmc0 = &sdhci0;
- mmc1 = &sdhci1;
- serial0 = &uart0;
- spi0 = &qspi;
- spi1 = &spi0;
- spi2 = &spi1;
- usb0 = &usb0;
- usb1 = &usb1;
- };
-
- chosen {
- bootargs = "earlycon";
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0 0x40000000>;
- };
-};
-
-&can0 {
- status = "okay";
-};
-
-&can1 {
- status = "okay";
-};
-
-&gem0 {
- status = "okay";
- phy-handle = <&phy0>;
- phy-mode = "rgmii-id";
- phy0: phy@0 {
- reg = <0>;
- max-speed = <100>;
- };
-};
-
-&gpio {
- status = "okay";
-};
-
-&i2c0 {
- status = "okay";
- clock-frequency = <400000>;
- eeprom@54 {
- compatible = "atmel,24c64";
- reg = <0x54>;
- };
-};
-
-&i2c1 {
- status = "okay";
- clock-frequency = <400000>;
- eeprom@55 {
- compatible = "atmel,24c64";
- reg = <0x55>;
- };
-};
-
-&nand0 {
- status = "okay";
- arasan,has-mdma;
- num-cs = <1>;
-
- partition@0 { /* for testing purpose */
- label = "nand-fsbl-uboot";
- reg = <0x0 0x0 0x400000>;
- };
- partition@1 { /* for testing purpose */
- label = "nand-linux";
- reg = <0x0 0x400000 0x1400000>;
- };
- partition@2 { /* for testing purpose */
- label = "nand-device-tree";
- reg = <0x0 0x1800000 0x400000>;
- };
- partition@3 { /* for testing purpose */
- label = "nand-rootfs";
- reg = <0x0 0x1C00000 0x1400000>;
- };
- partition@4 { /* for testing purpose */
- label = "nand-bitstream";
- reg = <0x0 0x3000000 0x400000>;
- };
- partition@5 { /* for testing purpose */
- label = "nand-misc";
- reg = <0x0 0x3400000 0xFCC00000>;
- };
-};
-
-&qspi {
- status = "okay";
- flash@0 {
- compatible = "m25p80";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x0>;
- spi-tx-bus-width = <1>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <10000000>;
- partition@qspi-fsbl-uboot { /* for testing purpose */
- label = "qspi-fsbl-uboot";
- reg = <0x0 0x100000>;
- };
- partition@qspi-linux { /* for testing purpose */
- label = "qspi-linux";
- reg = <0x100000 0x500000>;
- };
- partition@qspi-device-tree { /* for testing purpose */
- label = "qspi-device-tree";
- reg = <0x600000 0x20000>;
- };
- partition@qspi-rootfs { /* for testing purpose */
- label = "qspi-rootfs";
- reg = <0x620000 0x5E0000>;
- };
- };
-};
-
-&sata {
- status = "okay";
- ceva,broken-gen2;
- /* SATA Phy OOB timing settings */
- ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
- ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
- ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
- ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>;
- ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
- ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
- ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
- ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>;
-};
-
-&sdhci0 {
- status = "okay";
- bus-width = <8>;
- xlnx,mio_bank = <2>;
-};
-
-&sdhci1 {
- status = "okay";
- xlnx,mio_bank = <1>;
-};
-
-&spi0 {
- status = "okay";
- num-cs = <1>;
- spi0_flash0: spi0_flash0@0 {
- compatible = "m25p80";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- spi0_flash0@0 {
- label = "spi0_flash0";
- reg = <0x0 0x100000>;
- };
- };
-};
-
-&spi1 {
- status = "okay";
- num-cs = <1>;
- spi1_flash0: spi1_flash0@0 {
- compatible = "m25p80";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- spi1_flash0@0 {
- label = "spi1_flash0";
- reg = <0x0 0x100000>;
- };
- };
-};
-
-&uart0 {
- status = "okay";
-};
-
-&usb0 {
- status = "okay";
-};
-
-&dwc3_0 {
- status = "okay";
- dr_mode = "peripheral";
- maximum-speed = "high-speed";
-};
-
-&usb1 {
- status = "okay";
-};
-
-&dwc3_1 {
- status = "okay";
- dr_mode = "host";
- maximum-speed = "high-speed";
-};
-
-&watchdog0 {
- status = "okay";
-};
-
-&xlnx_dp {
- xlnx,max-pclock-frequency = <200000>;
-};
-
-&xlnx_dpdma {
- xlnx,axi-clock-freq = <200000000>;
-};
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_SYS_CONFIG_NAME="xilinx_zynqmp_ep"
-CONFIG_ARCH_ZYNQMP=y
-CONFIG_SYS_TEXT_BASE=0x8000000
-CONFIG_SYS_MALLOC_F_LEN=0x8000
-CONFIG_SPL=y
-CONFIG_ZYNQ_SDHCI_MAX_FREQ=52000000
-CONFIG_ZYNQMP_USB=y
-CONFIG_DEFAULT_DEVICE_TREE="zynqmp-ep108"
-CONFIG_DEBUG_UART=y
-CONFIG_AHCI=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_SPL_LOAD_FIT=y
-# CONFIG_DISPLAY_CPUINFO is not set
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_SPL_OS_BOOT=y
-CONFIG_SYS_PROMPT="ZynqMP> "
-CONFIG_FASTBOOT=y
-CONFIG_FASTBOOT_FLASH=y
-CONFIG_FASTBOOT_FLASH_MMC_DEV=0
-# CONFIG_CMD_CONSOLE is not set
-# CONFIG_CMD_XIMG is not set
-CONFIG_CMD_THOR_DOWNLOAD=y
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_ENV_EXISTS is not set
-CONFIG_CMD_CLK=y
-CONFIG_CMD_DFU=y
-# CONFIG_CMD_FPGA is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-# CONFIG_CMD_LOADB is not set
-# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_LOCK_UNLOCK=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_TFTPPUT=y
-# CONFIG_CMD_NFS is not set
-CONFIG_CMD_TIME=y
-CONFIG_CMD_TIMER=y
-CONFIG_CMD_EXT4_WRITE=y
-# CONFIG_SPL_ISO_PARTITION is not set
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_OF_EMBED=y
-CONFIG_ENV_IS_IN_FAT=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_SCSI_AHCI=y
-CONFIG_SATA_CEVA=y
-CONFIG_DFU_RAM=y
-CONFIG_FPGA_XILINX=y
-CONFIG_FPGA_ZYNQMPPL=y
-CONFIG_DM_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SYS_I2C_CADENCE=y
-CONFIG_MISC=y
-CONFIG_DM_MMC=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_ZYNQ=y
-CONFIG_ZYNQ_SDHCI_MIN_FREQ=100000
-CONFIG_NAND=y
-CONFIG_NAND_ARASAN=y
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_WINBOND=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TI=y
-CONFIG_PHY_VITESSE=y
-CONFIG_DM_ETH=y
-CONFIG_PHY_GIGE=y
-CONFIG_ZYNQ_GEM=y
-CONFIG_SCSI=y
-CONFIG_DM_SCSI=y
-CONFIG_DEBUG_UART_ZYNQ=y
-CONFIG_DEBUG_UART_BASE=0xff000000
-CONFIG_DEBUG_UART_CLOCK=25000000
-CONFIG_DEBUG_UART_ANNOUNCE=y
-CONFIG_ZYNQ_SERIAL=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-CONFIG_USB_XHCI_ZYNQMP=y
-CONFIG_USB_DWC3=y
-CONFIG_USB_DWC3_GADGET=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
-CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
-CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
-CONFIG_USB_FUNCTION_THOR=y
-# CONFIG_REGEX is not set
-CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
+++ /dev/null
-/*
- * Configuration for Xilinx ZynqMP emulation platforms
- *
- * (C) Copyright 2014 - 2015 Xilinx, Inc.
- * Michal Simek <michal.simek@xilinx.com>
- * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
- *
- * Based on Configuration for Versatile Express
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_ZYNQMP_EP_H
-#define __CONFIG_ZYNQMP_EP_H
-
-#define CONFIG_ZYNQ_EEPROM
-#define CONFIG_ZYNQMP_XHCI_LIST {ZYNQMP_USB0_XHCI_BASEADDR, \
- ZYNQMP_USB1_XHCI_BASEADDR}
-
-#define COUNTER_FREQUENCY 4000000
-
-#include <configs/xilinx_zynqmp.h>
-
-#endif /* __CONFIG_ZYNQMP_EP_H */
projects / platform / kernel / u-boot.git / commitdiff